GLS85VM1004A / 1008A / 1016A / 1032A Industrial Temp eMMC NANDriveTM Fact Sheet 03.000 June 2016 Features * Industry Standard Embedded MultiMediaCard (eMMC) Host Interface - JEDEC/MMC Standard Version 4.4 JESD84-A44 compliant - Backward compatible with eMMC 4.3 * Performance - eMMC clock speed: Up to 52MHz (Support x1/x4/x8 bus and Dual Data Rate mode) - Sequential data read: Up to 60 MByte/sec * - Sequential data write: Up to 30 MByte/sec * * Expanded Data Protection - Hardware Write Protection pin * Latency Management - Reduce latencies due to background operation during time critical read/write operations * Integrated Voltage Detector - Detects supply voltage fluctuations and generates reset during power-up and powerdown to prevent inadvertent writes * Robust Built-in ECC * NAND Configuration - 2 bits per cell (MLC) * Temperature Range - Industrial: -40C to 85C * 100-ball LBGA Package - 14.0 mm x 18.0 mm x 1.40 mm, 100-ball, 1.0 mm ball pitch, LFWE (GLS85VM1004A/8A/16A/32A) * All Devices are RoHS Compliant * measured using 128 Kbyte transfer size * Power Management - 3.3V power supply - 3.3V or 1.8V eMMC IO voltage - Immediate disabling of unused circuitry without Host intervention * Power Specifications - Active mode 180mA typical (GLS85VM1032A) 150mA typical (GLS85VM1016A) 120mA typical (GLS85VM1008A) 120mA typical (GLS85VM1004A) - Sleep mode 200A typical Product Description The GLS85VM1004A / 1008A / VM1016A / VM1032A eMMC NANDriveTM devices (referred to as "eMMC NANDrive" in this datasheet) are fully integrated solid state drives. They combine an advanced Greenliant NAND controller and 4, 8, 16 or 32 GByte of NAND flash memory in a multi-chip package. These products are ideal for solid state mass storage in embedded and portable applications that require small formfactor, energy efficient and reliable data storage. The integrated NAND flash controller with built-in advanced NAND management firmware communicates with the Host through the standard eMMC protocol. It does not require any additional or proprietary software such as the Flash File System (FFS) and Memory Technology Driver (MTD). eMMC NANDrive's advanced NAND management technology enhances data security, improves endurance and accurately tracks the usage of the NAND flash. This innovative technology combines robust error correction capabilities with advanced wear-leveling algorithms and bad block management to extend the life of the product. eMMC solid state drives are widely used in GPS and telematics, in-vehicle infotainment, portable and industrial computers, handheld data collection scanners, point-of-sale terminals, networking and telecommunications equipment, robotics, audio and video recorders, monitoring devices and set-top boxes. eMMC NANDrive supports Dual Data Rate (DDR) mode, boot, multiple partitions, permanent and partial write protect, Replay Protected Memory Block (RPMB) access, Secure erase and TRIM, hardware reset and other features detailed in the eMMC 4.4 standard specification. It is fully backward compatible with the eMMC 4.3 standard. eMMC NANDrive provides complete eMMC solid state drive (SSD) functionality and compatibility in a 14mm x 18mm BGA package for easy, space saving mounting to a system motherboard. With its small size, low power consumption, strong security, reliability and ruggedness, eMMC NANDrive surpasses removable storage and discrete NAND-based products. These specifications are subject to change without notice. (c) 2016 Greenliant Systems 1 06/15/2016 S71425-F GLS85VM1004A / 1008A / 1016A / 1032A Industrial Temp eMMC NANDriveTM Fact Sheet 03.000 June 2016 1.0 GENERAL DESCRIPTION Each eMMC NANDrive contains an integrated eMMC NAND flash memory controller and NAND flash die in a BGA package. Refer to Figure 2-1 for the eMMC NANDrive block diagram. 1.1 1.1.5 Error Correction Code (ECC) High performance is achieved through optimized hardware error detection and correction. Optimized eMMC NANDrive The heart of the eMMC NANDrive is the eMMC NAND flash memory controller, which translates standard eMMC signals into flash media data and control signals. The following components contribute to the eMMC NANDrive's operation. 1.1.6 Serial Communication Interface (SCI) The Serial Communication Interface (SCI) is designed for error reporting. During the product development stage, it is recommended to provide the SCI port on the PCB to aid in design validation. 1.1.1 Microcontroller Unit (MCU) The MCU transfers the eMMC commands into data and control signals required for flash media operation. 1.1.7 Multi-tasking Interface The multi-tasking interface enables fast, sequential write performance by allowing concurrent Read, Program and Erase operations to multiple flash media. 1.1.2 Internal Direct Memory Access (DMA) The eMMC NANDrive uses internal DMA allowing instant data transfer from/to buffer to/from flash media. This implementation eliminates microcontroller overhead associated with the traditional, firmwarebased approach, thereby increasing the data transfer rate. 1.2 SMT Reflow Consideration The eMMC NANDrive family utilizes standard NAND flash for data storage. Because the high temperature in a surface-mount soldering reflow process may alter the content on NAND flash, it is recommended to program the eMMC NANDrive after the reflow process. 1.1.3 Power Management Unit (PMU) The PMU controls the power consumption of the eMMC NANDrive. The PMU dramatically reduces the power consumption of the eMMC NANDrive by putting the part of the circuitry that is not in operation into sleep mode. 1.3 Advanced NAND Management The eMMC NANDrive's integrated controller uses advanced wear-leveling algorithms to substantially increase the longevity of NAND flash media. Wear caused by data writes is evenly distributed in all or select blocks in the device that prevents "hot spots" in locations that are programmed and erased extensively. This effective wear-leveling technique results in optimized device endurance, enhanced data retention and higher reliability required by long-life applications. The Flash File System handles inadvertent power interrupts and has auto-recovery capability to ensure the eMMC NANDrive's data integrity. 1.1.4 Embedded Flash File System The embedded flash file system is an integral part of the eMMC NANDrive. It contains MCU firmware that performs the following tasks: 1. Translates host side signals into flash media writes and reads 2. Provides flash media wear leveling to spread flash writes across all memory address space to increase the longevity of flash media 3. Keeps track of the data file structure 4. Manages system security for the selected protection zones These specifications are subject to change without notice. (c) 2016 Greenliant Systems 2 06/15/2016 S71425-F GLS85VM1004A / 1008A / 1016A / 1032A Industrial Temp eMMC NANDriveTM Fact Sheet 03.000 June 2016 2.0 FUNCTIONAL BLOCKS eMMC NANDrive NAND Controller MCU eMMC HOST I/F SRAM Buffer Memory Channel I/F eMMC Flash Media I/F NAND I/F I/F ECC Internal DMA PMU NAND NAND NAND NAND NAND Chips Chips Chips Chips Flash SCI Figure 2-1: eMMC NANDrive Block Diagram These specifications are subject to change without notice. (c) 2016 Greenliant Systems 3 06/15/2016 S71425-F GLS85VM1004A / 1008A / 1016A / 1032A Industrial Temp eMMC NANDriveTM Fact Sheet 03.000 June 2016 3.0 PRODUCT ORDERING INFORMATION GLS 85 VM 1 0xx A - M - I - LFW E - NDxxx XX XX X XXX X - X - X - XXXX - XXXXX 1) Ordering Code NDxxx = NANDrive Revision EDxxx = Evaluation Board Revision Environmental Attribute E = non-Pb solder (RoHS Compliant) Package Modifier W = 100-ball positions Package Type LF = LBGA (max. package height 1.40mm) Operation Temperature I = Industrial: -40C to +85C NAND Configuration M = 2 bits per cell Generation / Product Configuration A = First generation Capacity 004 = 4 GByte 008 = 8 GByte 016 = 16 GByte 032 = 32 GByte MByte or GByte Designator 0 = MByte 1 = GByte Interface M = eMMC Voltage V = 2.7V to 3.3V Product Series 85 = NANDrive 1) Note that the top side marking on the package typically does not include ordering codes (e.g. NDxxx), unless it is a special C-SPEC (custom specification) which is required by the end-customer to be marked on the device. These specifications are subject to change without notice. (c) 2016 Greenliant Systems 4 06/15/2016 S71425-F GLS85VM1004A / 1008A / 1016A / 1032A Industrial Temp eMMC NANDriveTM Fact Sheet 03.000 June 2016 Valid Combinations Valid product combinations are those that are in the mass production or will be in the mass production. Consult your Greenliant sales representative to confirm availability of the valid combinations and to determine availability of new product combinations. Table 3-1: eMMC NANDrive Product Valid Ordering Numbers Capacity Operating Temperature Part Number Package 4GB Industrial (-40C to 85C) GLS85VM1004A-M-I-LFWE-ND206 LFWE, 14x18x1.40mm 4GB Industrial (-40C to 85C) GLS85VM1004A-M-I-LFWE-ND209 LFWE, 14x18x1.40mm 8GB Industrial (-40C to 85C) GLS85VM1008A-M-I-LFWE-ND206 LFWE, 14x18x1.40mm 8GB Industrial (-40C to 85C) GLS85VM1008A-M-I-LFWE-ND209 LFWE, 14x18x1.40mm 16GB Industrial (-40C to 85C) GLS85VM1016A-M-I-LFWE-ND206 LFWE, 14x18x1.40mm 16GB Industrial (-40C to 85C) GLS85VM1016A-M-I-LFWE-ND209 LFWE, 14x18x1.40mm 32GB Industrial (-40C to 85C) GLS85VM1032A-M-I-LFWE-ND206 LFWE, 14x18x1.40mm 32GB Industrial (-40C to 85C) GLS85VM1032A-M-I-LFWE-ND209 LFWE, 14x18x1.40mm Table 3-2: eMMC Evaluation Board Valid Ordering Numbers Capacity Operating Temperature Part Number 4GB Industrial (-40C to 85C) GLS85VM1004A-M-I-E2-ED209 Form Factor JEDEC MO-277 8GB Industrial (-40C to 85C) GLS85VM1008A-M-I-E2-ED209 JEDEC MO-277 16GB Industrial (-40C to 85C) GLS85VM1016A-M-I-E2-ED209 JEDEC MO-277 32GB Industrial (-40C to 85C) GLS85VM1032A-M-I-E2-ED209 JEDEC MO-277 These specifications are subject to change without notice. (c) 2016 Greenliant Systems 5 06/15/2016 S71425-F GLS85VM1004A / 1008A / 1016A / 1032A Industrial Temp eMMC NANDriveTM Fact Sheet 03.000 June 2016 3.1 Package Diagram Note: All linear dimensions are in millimeters. Untoleranced dimensions are nominal target values. Coplanarity: 0.12 mm Ball diameter is 0.45 mm ( 0.05 mm) Ball opening size is 0.38 mm ( 0.05 mm), SMD type Figure 3-1: eMMC NANDrive 100-Ball, Ball Grid Array (BGA) Greenliant Package Code: LFWE These specifications are subject to change without notice. (c) 2016 Greenliant Systems 6 06/15/2016 S71425-F GLS85VM1004A / 1008A / 1016A / 1032A Industrial Temp eMMC NANDriveTM Fact Sheet 03.000 June 2016 Revision History Number 01.000 02.000 03.000 Description Initial release as Fact Sheet Added GLS85VM1004A-M-I-LFWE Added Ordering Codes ND206/ND209/ED209, Removed ND202 Date March 22, 2013 August 26, 2013 June 15, 2016 (c) 2016 Greenliant Systems. All rights reserved. Greenliant and the Greenliant logo are registered trademarks, and NANDrive is a trademark of Greenliant Systems. All other trademarks and registered trademarks are the property of their respective owners. Specifications are subject to change without notice. Memory sizes denote raw storage capacity; actual usable capacity may be less. Greenliant makes no warranty for the use of its products other than those expressly contained in the Greenliant Terms and Conditions of Sale. www.greenliant.com These specifications are subject to change without notice. (c) 2016 Greenliant Systems 7 06/15/2016 S71425-F Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Greenliant: GLS85VM1016A-M-I-E1-ED202 GLS85VM1008A-M-I-LFWE-ND202 GLS85VM1008A-M-I-E1-ED202 GLS85VM1032A-M-I-LFWE-ND202 GLS85VM1004A-M-I-E2-ED202 GLS85VM1016A-M-I-LFWE-ND202 GLS85VM1004A-M-I-LFWE-ND202 GLS85VM1008A-M-I-E2-ED202 GLS85VM1016A-M-I-E2-ED202 GLS85VM1032A-M-I-LFWE-ND209 GLS85VM1004A-M-I-LFWE-ND209 GLS85VM1008A-M-I-LFWE-ND209 GLS85VM1016A-M-I-LFWE-ND209