ADC081C027CIMKX/NOPB - Texas Instruments High-Performance Analog

ADC081C021, ADC081C027

www.ti.com

SNAS447C –FEBRUARY 2008–REVISED MARCH 2013

ADC081C021/ADC081C027 I

C-Compatible, 8-Bit Analog-to-Digital Converter with Alert

Function

Check for Samples: ADC081C021,ADC081C027

1FEATURES DESCRIPTION

The ADC081C021 is a low-power, monolithic, 8-bit,

23• I2C-Compatible 2-Wire Interface Which analog-to-digital converter (ADC) that operates from a

Supports Standard (100kHz), Fast (400kHz), +2.7 to 5.5V supply. The converter is based on a

and High Speed (3.4MHz) Modes successive approximation register architecture with

• Extended Power Supply Range (+2.7V to an internal track-and-hold circuit that can handle input

+5.5V) frequencies up to 11MHz. The ADC081C021

operates from a single supply which also serves as

• Up to Nine Pin-Selectable Chip Addresses the reference. The device features an I2C-compatible

(VSSOP-8 only) serial interface that operates in all three speed

• Out-of-Range Alert Function modes, including high speed mode (3.4MHz).

• Automatic Power-Down Mode While Not The ADC's Alert feature provides an interrupt that is

Converting activated when the analog input violates a

• Very Small SOT-6 and VSSOP-8 Packages programmable upper or lower limit value. The device

features an automatic conversion mode, which frees

• ±8kV HBM ESD Protection (SDA, SCL) up the controller and I2C interface. In this mode, the

ADC continuously monitors the analog input for an

APPLICATIONS "out-of-range" condition and provides an interrupt if

• System Monitoring the measured voltage goes out-of-range.

• Peak Detection The ADC081C021 comes in two packages: a small

• Portable Instruments SOT-6 package with an alert output, and an VSSOP-

8 package with an alert output and two address

• Medical Instruments selection inputs. The ADC081C027 comes in a small

• Test Equipment SOT-6 package with an address selection input. The

ADC081C027 provides three pin-selectable

KEY SPECIFICATIONS addresses while the VSSOP-8 version of the

ADC081C021 provides nine pin-selectable

• Resolution: 8 bits; No Missing Codes addresses. Pin-compatible alternatives to the SOT-6

• Conversion Time 1 µs (Typ) options are available with additional address options.

• INL & DNL: ±0.2 LSB (Max) Normal power consumption using a +3V or +5V

• Throughput Rate: 188.9 ksps (Max) supply is 0.26mW or 0.78mW, respectively. The

• Power Consumption (at 22ksps): automatic power-down feature reduces the power

consumption to less than 1µW while not converting.

– 3V Supply: 0.26 mW (Typ) Operation over the industrial temperature range of

– 5V Supply: 0.78 mW (Typ) −40°C to +105°C is ensured. Their low power

consumption and small packages make this family of

ADCs an excellent choice for use in battery operated

equipment.

The ADC081C021 and ADC081C027 are part of a

family of pin-compatible ADCs that also provide 10-

and 12-bit resolution. For 10-bit ADCs see the

ADC101C021 and ADC101C027. For 12-bit ADCs

see the ADC121C021 and ADC121C027.

1Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of

Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

2I2C is a registered trademark of Phillips Corporation..

3All other trademarks are the property of their respective owners.

Products conform to specifications per the terms of the Texas

Instruments standard warranty. Production processing does not

necessarily include testing of all parameters.

ALERT

SCL

SDA

VIN

GND SOT

ADC081C021

ADDR

SCL

SDA

VIN

GND SOT

ADC081C027

ALERT

SDA

ADR1

GND

VSSOP

SCL

VIN

ADC081C021

ADR0

ADC081C021, ADC081C027

SNAS447C –FEBRUARY 2008–REVISED MARCH 2013

www.ti.com

Table 1. Pin-Compatible AlternativesAll devices are fully pin and function compatible.

Resolution SOT-6 (Alert only) and VSSOP-8 SOT-6 (Addr only)

12-bit ADC121C021 ADC121C027

10-bit ADC101C021 ADC101C027

8-bit ADC081C021 ADC081C027

Connection Diagrams

Figure 1. SOT (Alert Only) – See Figure 2. SOT (Addr Only) – See Figure 3. VSSOP – See Package

Package Number DDC Package Number DDC Number DGK

Product Folder Links: ADC081C021 ADC081C027

SDA

SCL

Lowest Conversion

Configuration

I2C Serial Interface

ADC081C021/

ADC081C027

Conversion Result

High Limit

Low Limit

Pointer

and

Decode

Logic

Alert

Set-Point

Comparator

ADDR*

Highest Conversion

8-Bit

Successive

Approximation

ADC

GND

Hysteresis

VIN

Alert Status

ALERT*

T/H

Oscillator

REF

* Note: The ADC081C021 has the ALERT pin but no ADDR pin.

The ADC081C027 has the ADDR pin but no ALERT pin.

ADC081C021, ADC081C027

www.ti.com

SNAS447C –FEBRUARY 2008–REVISED MARCH 2013

Block Diagram

PIN DESCRIPTIONS

Symbol Type Equivalent Circuit Description

Power and unbufferred reference voltage. VAmust be free

VASupply of noise and decoupled to GND.

GND Ground Ground for all on-chip circuitry.

VIN Analog Input See Figure 22 Analog input. This signal can range from GND to VA.

Product Folder Links: ADC081C021 ADC081C027

Snap

Back

GND

V+

2.1k 41.5k

41.5k

Snap

Back

GND

ADC081C021, ADC081C027

SNAS447C –FEBRUARY 2008–REVISED MARCH 2013

www.ti.com

PIN DESCRIPTIONS (continued)

Symbol Type Equivalent Circuit Description

Alert output. Can be configured as active high or active low.

ALERT Digital Output This is an open drain data line that must be pulled to the

supply (VA) with an external pull-up resistor.

Serial Clock Input. SCL is used together with SDA to control

the transfer of data in and out of the device. This is an open

drain data line that must be pulled to the supply (VA) with an

SCL Digital Input external pull-up resistor. This pin's extended ESD tolerance(

8kV HBM) allows extension of the I2C bus across multiple

boards without extra ESD protection.

Serial Data bi-directional connection. Data is clocked into or

out of the internal 16-bit register with SCL. This is an open

Digital drain data line that must be pulled to the supply (VA) with an

SDA Input/Output external pull-up resistor. This pin's extended ESD tolerance(

8kV HBM) allows extension of the I2C bus across multiple

boards without extra ESD protection.

Tri-level Address Selection Input. Sets Bits A0 & A1 of the

ADDR0 7-bit slave address. (see Table 2)

Digital Input,

three levels Tri-level Address Selection Input. Sets Bits A2 & A3 of the

ADDR1 7-bit slave address. (see Table 2)

Package Pinouts

VAGND VIN ALERT SCL SDA ADR0 ADR1

ADC081C021 (SOT-6) 1 2 3 4 5 6 N/A N/A

ADC081C027 (SOT-6) 1 2 3 N/A 5 6 4 N/A

ADC081C021 (VSSOP-8) 57421836

These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam

during storage or handling to prevent electrostatic damage to the MOS gates.

Product Folder Links: ADC081C021 ADC081C027

I/O

GND

TO INTERNAL

CIRCUITRY

ADC081C021, ADC081C027

www.ti.com

SNAS447C –FEBRUARY 2008–REVISED MARCH 2013

Absolute Maximum Ratings(1)(2)(3)

Supply Voltage, VA(4) -0.3V to +6.5V

Voltage on any Analog Input Pin to GND −0.3V to (VA+0.3V)

Voltage on any Digital Input Pin to GND −0.3V to 6.5V

Input Current at Any Pin(5) ±15 mA

Package Input Current(5) ±20 mA

Power Dissipation at TA= 25°C See(6)

Human Body Model 2500V

VA, GND, VIN, ALERT, ADR pins Machine Model 250V

ESD Susceptibility(7) Charged Device Model (CDM) 1250V

Human Body Model 8000V

SDA, SCL pins Machine Model 400V

Junction Temperature +150°C

Storage Temperature −65°C to +150°C

(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for

which the device is functional, but do not ensure specific performance limits. For ensured specifications and test conditions, see the

Electrical Characteristics. The ensured specifications apply only for the test conditions listed. Some performance characteristics may

degrade when the device is not operated under the listed test conditions. Operation of the device beyond the maximum Operating

Ratings is not recommended.

(2) All voltages are measured with respect to GND = 0V, unless otherwise specified.

(3) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and

specifications.

(4) To ensure accuracy, it is required that VAbe well bypassed and free of noise.

(5) When the input voltage at any pin exceeds 5.5V or is less than GND, the current at that pin should be limited per the Absolute Maximum

Ratings. The maximum package input current rating limits the number of pins that can safely exceed the power supplies.

(6) The absolute maximum junction temperature (TJmax) for this device is 150°C. The maximum allowable power dissipation is dictated by

TJmax, the junction-to-ambient thermal resistance (θJA), and the ambient temperature (TA), and can be calculated using the formula

PDMAX = (TJmax −TA) / θJA. The values for maximum power dissipation will be reached only when the device is operated in a severe

fault condition (e.g., when input or output pins are driven beyond the operating ratings, or the power supply polarity is reversed).

(7) Human body model is a 100 pF capacitor discharged through a 1.5 kΩresistor. Machine model is a 220 pF capacitor discharged

through 0 Ω. Charged device model simulates a pin slowly acquiring charge (such as from a device sliding down the feeder in an

automated assembler) then rapidly being discharged.

Operating Ratings(1)(2)

Operating Temperature Range −40°C ≤TA≤+105°C

Supply Voltage, VA+2.7V to 5.5V

Analog Input Voltage, VIN 0V to VA

Digital Input Voltage(3) 0V to 5.5V

Sample Rate up to 188.9 ksps

(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for

which the device is functional, but do not ensure specific performance limits. For ensured specifications and test conditions, see the

Electrical Characteristics. The ensured specifications apply only for the test conditions listed. Some performance characteristics may

degrade when the device is not operated under the listed test conditions. Operation of the device beyond the maximum Operating

Ratings is not recommended.

(2) All voltages are measured with respect to GND = 0V, unless otherwise specified.

(3) The inputs are protected as shown below. Input voltage magnitudes up to 5.5V, regardless of VA, will not cause errors in the conversion

result. For example, if VAis 3V, the digital input pins can be driven with a 5V logic device.

Product Folder Links: ADC081C021 ADC081C027

ADC081C021, ADC081C027

SNAS447C –FEBRUARY 2008–REVISED MARCH 2013

www.ti.com

Package Thermal Resistances(1)(2)

Package θJA

6-Lead SOT 250°C/W

8-Lead VSSOP 200°C/W

(1) Soldering process must comply with Reflow Temperature Profile specifications. Refer to www.ti.com/packaging.

(2) Reflow temperature profiles are different for lead-free packages.

Electrical Characteristics

The following specifications apply for VA= +2.7V to +5.5V, GND = 0V, fSCL up to 3.4MHz, fIN = 1kHz for fSCL up to 400kHz, fIN

= 10kHz for fSCL = 3.4MHz unless otherwise noted. Boldface limits apply for TA= TMIN to TMAX: all other limits TA= 25°C

unless otherwise noted.

Symbol Parameter Conditions Typical(1) Limits(1) Units (Limits)

STATIC CONVERTER CHARACTERISTICS

Resolution with No Missing Codes 8Bits

VA= +2.7V to +3.6V ±0.04 ±0.2 LSB (max)

Integral Non-Linearity (End Point

INL Method) VA= +2.7V to +5.5V. fSCL up to 400kHz(2) ±0.1 ±0.25 LSB (max)

VA= +2.7V to +3.6V +0.04 ±0.2 LSB (max)

DNL Differential Non-Linearity VA= +2.7V to +5.5V. fSCL up to 400kHz(2) ±0.08 ±0.25 LSB (max)

VA= +2.7V to +3.6V +0.26 ±0.5 LSB (max)

VOFF Offset Error VA= +2.7V to +5.5V. fSCL up to 400kHz(2) +0.25 ±0.5 LSB (max)

GE Gain Error -0.01 ±0.4 LSB (max)

DYNAMIC CONVERTER CHARACTERISTICS

ENOB Effective Number of Bits 7.98 7.8 Bits (min)

SNR Signal-to-Noise Ratio 49.8 49 dB (min)

THD Total Harmonic Distortion −70.6 −64 dB (max)

SINAD Signal-to-Noise Plus Distortion Ratio 49.8 49 dB (min)

SFDR Spurious-Free Dynamic Range -68.8 65 dB (min)

Intermodulation Distortion, Second

IMD VA= +3.0V, fa= 1.035 kHz, fb= 1.135 kHz −75.5 dB

Order Terms (IMD2)

Intermodulation Distortion, Third VA= +3.0V, fa= 1.035 kHz, fb= 1.135 kHz −71.8 dB

Order Terms (IMD3)VA= +3.0V 8 MHz

FPBW Full Power Bandwidth (−3dB) VA= +5.0V 11 MHz

ANALOG INPUT CHARACTERISTICS

VIN Input Range 0 to VAV

IDCL DC Leakage Current(3) ±1 µA (max)

Track Mode 30 pF

CINA Input Capacitance Hold Mode 3 pF

SERIAL INTERFACE INPUT CHARACTERISTICS (SCL, SDA)

VIH Input High Voltage 0.7 x VAV (min)

VIL Input Low Voltage 0.3 x VAV (max)

IIN Input Current(3) ±1 µA (max)

CIN Input Pin Capacitance 3 pF

VHYST Input Hysteresis 0.1 x VAV (min)

ADDRESS SELECTION INPUT CHARACTERISTICS (ADDR)

VIH Input High Voltage VA- 0.5V V (min)

VIL Input Low Voltage 0.5 V (max)

(1) Typical figures are at TJ= 25°C, and represent most likely parametric norms. Test limits are specified to AOQL (Average Outgoing

Quality Level).

(2) The ADC will meet Minimum/Maximum specifications for fSCL up to 3.4MHz and VA= 2.7V to 3.6V when operating in the QUIET

INTERFACE MODE.

(3) This parameter is specified by design and/or characterization and is not tested in production.

Product Folder Links: ADC081C021 ADC081C027

ADC081C021, ADC081C027

www.ti.com

SNAS447C –FEBRUARY 2008–REVISED MARCH 2013

Electrical Characteristics (continued)

The following specifications apply for VA= +2.7V to +5.5V, GND = 0V, fSCL up to 3.4MHz, fIN = 1kHz for fSCL up to 400kHz, fIN

= 10kHz for fSCL = 3.4MHz unless otherwise noted. Boldface limits apply for TA= TMIN to TMAX: all other limits TA= 25°C

unless otherwise noted.

Symbol Parameter Conditions Typical(1) Limits(1) Units (Limits)

IIN Input Current(3) ±1 µA (max)

LOGIC OUTPUT CHARACTERISTICS, OPEN-DRAIN (SDA, ALERT)

ISINK = 3 mA 0.4 V (max)

VOL Output Low Voltage ISINK = 6 mA 0.6 V (max)

High-Impedence Output Leakage

IOZ ±1 µA (max)

Current(3)

Output Coding Straight (Natural) Binary

POWER REQUIREMENTS

Supply Voltage Minimum 2.7 V (min)

VASupply Voltage Maximum 5.5 V (max)

Continuous Operation Mode -- 2-wire interface active. VA= 2.7V to 3.6V 0.08 0.14 mA (max)

fSCL=400kHz VA= 4.5V to 5.5V 0.16 0.30 mA (max)

INSupply Current VA= 2.7V to 3.6V 0.37 0.55 mA (max)

fSCL=3.4MHz VA= 4.5V to 5.5V 0.74 0.99 mA (max)

VA= 3.0V 0.26 mW

fSCL=400kHz VA= 5.0V 0.78 mW

PNPower Consumption VA= 3.0V 1.22 mW

fSCL=3.4MHz VA= 5.0V 3.67 mW

Automatic Conversion Mode -- 2-wire interface stopped and quiet (SCL = SDA = VA). fSAMPLE = TCONVERT * 32

VA= 2.7V to 3.6V 0.41 0.59 mA (max)

IASupply Current VA= 4.5V to 5.5V 0.78 1.2 mA (max)

VA= 3.0V 1.35 mW

PAPower Consumption VA= 5.0V 3.91 mW

Power Down Mode (PD1) -- 2-wire interface stopped and quiet. (SCL = SDA = VA).(4)

IPD1 Supply Current 0.1 0.2 µA (max)

PPD1 Power Consumption 0.5 0.9 µW (max)

Power Down Mode (PD2) -- 2-wire interface active. Master communicating with a different device on the bus.

VA= 2.7V to 3.6V 13 45 µA (max)

fSCL=400kHz VA= 4.5V to 5.5V 27 80 µA (max)

IPD2 Supply Current VA= 2.7V to 3.6V 89 150 µA (max)

fSCL=3.4MHz VA= 4.5V to 5.5V 168 250 µA (max)

VA= 3.0V 0.04 mW

fSCL=400kHz VA= 5.0V 0.14 mW

PPD2 Power Consumption VA= 3.0V 0.29 mW

fSCL=3.4MHz VA= 5.0V 0.84 mW

(4) This parameter is specified by design and/or characterization and is not tested in production.

Product Folder Links: ADC081C021 ADC081C027

ADC081C021, ADC081C027

SNAS447C –FEBRUARY 2008–REVISED MARCH 2013

www.ti.com

A.C. and Timing Characteristics

The following specifications apply for VA= +2.7V to +5.5V. Boldface limits apply for TMIN ≤TA≤TMAX and all other limits are

at TA= 25°C, unless otherwise specified. Units

Symbol Parameter Conditions(1) Typical(2) Limits(1)(2) (Limits)

CONVERSION RATE

Conversion Time 1 µs

fSCL = 100kHz 5.56 ksps

fSCL = 400kHz 22.2 ksps

fCONV Conversion Rate fSCL = 1.7MHz 94.4 ksps

fSCL = 3.4MHz 188.9 ksps

DIGITAL TIMING SPECS (SCL, SDA)

Standard Mode 100 kHz (max)

Fast Mode 400 kHz (max)

fSCL Serial Clock Frequency High Speed Mode, Cb= 100pF 3.4 MHz (max)

High Speed Mode, Cb= 400pF 1.7 MHz (max)

Standard Mode 4.7 us (min)

Fast Mode 1.3 us (min)

tLOW SCL Low Time High Speed Mode, Cb= 100pF 160 ns (min)

High Speed Mode, Cb= 400pF 320 ns (min)

Standard Mode 4.0 us (min)

Fast Mode 0.6 us (min)

tHIGH SCL High Time High Speed Mode, Cb= 100pF 60 ns (min)

High Speed Mode, Cb= 400pF 120 ns (min)

Standard Mode 250 ns (min)

tSU;DAT Data Setup Time Fast Mode 100 ns (min)

High Speed Mode 10 ns (min)

0us (min)

Standard Mode(3) 3.45 us (max)

0us (min)

Fast Mode(3) 0.9 us (max)

tHD;DAT Data Hold Time 0ns (min)

High Speed Mode, Cb= 100pF 70 ns (max)

0ns (min)

High Speed Mode, Cb= 400pF 150 ns (max)

Standard Mode 4.7 us (min)

Setup time for a start or a repeated

tSU;STA Fast Mode 0.6 us (min)

start condition High Speed Mode 160 ns (min)

Standard Mode 4.0 us (min)

Hold time for a start or a repeated start

tHD;STA Fast Mode 0.6 us (min)

condition High Speed Mode 160 ns (min)

Bus free time between a stop and start Standard Mode 4.7 us (min)

tBUF condition Fast Mode 1.3 us (min)

Standard Mode 4.0 us (min)

tSU;STO Setup time for a stop condition Fast Mode 0.6 us (min)

High Speed Mode 160 ns (min)

Standard Mode 1000 ns (max)

20+0.1Cbns (min)

Fast Mode 300 ns (max)

trDA Rise time of SDA signal 10 ns (min)

High Speed Mode, Cb= 100pF 80 ns (max)

20 ns (min)

High Speed Mode, Cb= 400pF 160 ns (max)

(1) Cbrefers to the capacitance of one bus line. Cbis expressed in pF units.

(2) Typical figures are at TJ= 25°C, and represent most likely parametric norms. Test limits are specified to AOQL (Average Outgoing

Quality Level).

(3) The ADC081C021 will provide a minimum data hold time of 300ns to comply with the I2C Specification.

Product Folder Links: ADC081C021 ADC081C027

SCL

SDA

tHD;STA

tLOW

tHD;DAT tHIGH

tSU;DAT

tSU;STA tSU;STO

START REPEATED

START STOP

tHD;STA

START

tSP

trtBUF

ADC081C021, ADC081C027

www.ti.com

SNAS447C –FEBRUARY 2008–REVISED MARCH 2013

A.C. and Timing Characteristics (continued)

The following specifications apply for VA= +2.7V to +5.5V. Boldface limits apply for TMIN ≤TA≤TMAX and all other limits are

at TA= 25°C, unless otherwise specified. Units

Symbol Parameter Conditions(1) Typical(2) Limits(1)(2) (Limits)

Standard Mode 250 ns (max)

20+0.1Cbns (min)

Fast Mode 250 ns (max)

tfDA Fall time of SDA signal 10 ns (min)

High Speed Mode, Cb= 100pF 80 ns (max)

20 ns (min)

High Speed Mode, Cb= 400pF 160 ns (max)

Standard Mode 1000 ns (max)

20+0.1Cbns (min)

Fast Mode 300 ns (max)

trCL Rise time of SCL signal 10 ns (min)

High Speed Mode, Cb= 100pF 40 ns (max)

20 ns (min)

High Speed Mode, Cb= 400pF 80 ns (max)

Standard Mode 1000 ns (max)

20+0.1Cbns (min)

Fast Mode 300 ns (max)

Rise time of SCL signal after a

trCL1 repeated start condition and after an 10 ns (min)

High Speed Mode, Cb= 100pF

acknowledge bit. 80 ns (max)

20 ns (min)

High Speed Mode, Cb= 400pF 160 ns (max)

Standard Mode 300 ns (max)

20+0.1Cbns (min)

Fast Mode 300 ns (max)

tfCL Fall time of a SCL signal 10 ns (min)

High Speed Mode, Cb= 100pF 40 ns (max)

20 ns (min)

High Speed Mode, Cb= 400pF 80 ns (max)

Capacitive load for each bus line (SCL

Cb400 pF (max)

and SDA) Fast Mode 50 ns (max)

tSP Pulse Width of spike suppressed(4) High Speed Mode 10 ns (max)

(4) Spike suppression filtering on SCL and SDA will suppress spikes that are less than 50ns for standard and fast modes, and less than

10ns for hs-mode.

Timing Diagrams

Figure 4. Serial Timing Diagram

Product Folder Links: ADC081C021 ADC081C027

A++A

logTHD = 20 /

ADC081C021, ADC081C027

SNAS447C –FEBRUARY 2008–REVISED MARCH 2013

www.ti.com

Specification Definitions

ACQUISITION TIME is the time required for the ADC to acquire the input voltage. During this time, the hold

capacitor is charged by the input voltage.

APERTURE DELAY is the time between the start of a conversion and the time when the input signal is internally

acquired or held for conversion.

CONVERSION TIME is the time required, after the input voltage is acquired, for the ADC to convert the input

voltage to a digital word.

DIFFERENTIAL NON-LINEARITY (DNL) is the measure of the maximum deviation from the ideal step size of 1

LSB.

EFFECTIVE NUMBER OF BITS (ENOB, or EFFECTIVE BITS) is another method of specifying Signal-to-Noise

and Distortion or SINAD. ENOB is defined as (SINAD - 1.76) / 6.02 and says that the converter is equivalent to a

perfect ADC of this (ENOB) number of bits.

FULL POWER BANDWIDTH is a measure of the frequency at which the reconstructed output fundamental

drops 3 dB below its low frequency value for a full scale input.

GAIN ERROR is the deviation of the last code transition (111...110) to (111...111) from the ideal (VREF - 1.5

LSB), after adjusting for offset error.

INTEGRAL NON-LINEARITY (INL) is a measure of the deviation of each individual code from a line drawn from

negative full scale (½ LSB below the first code transition) through positive full scale (½ LSB above the last code

transition). The deviation of any given code from this straight line is measured from the center of that code value.

INTERMODULATION DISTORTION (IMD) is the creation of additional spectral components as a result of two

sinusoidal frequencies being applied to an individual ADC input at the same time. It is defined as the ratio of the

power in both the second and third order intermodulation products to the power in one of the original frequencies.

Second order products are fa± fb, where faand fbare the two sine wave input frequencies. Third order products

are (2fa± fb) and (fa± 2fb). IMD is usually expressed in dB.

MISSING CODES are those output codes that will never appear at the ADC output. The ADC081C021 is

ensured not to have any missing codes.

OFFSET ERROR is the deviation of the first code transition (000...000) to (000...001) from the ideal (i.e. GND +

0.5 LSB).

SIGNAL TO NOISE RATIO (SNR) is the ratio, expressed in dB, of the rms value of the input signal to the rms

value of the sum of all other spectral components below one-half the sampling frequency, not including

harmonics or d.c.

SIGNAL TO NOISE PLUS DISTORTION (S/N+D or SINAD) Is the ratio, expressed in dB, of the rms value of the

input signal to the rms value of all of the other spectral components below half the clock frequency, including

harmonics but excluding d.c.

SPURIOUS FREE DYNAMIC RANGE (SFDR) is the difference, expressed in dB, between the desired signal

amplitude to the amplitude of the peak spurious spectral component, where a spurious spectral component is

any signal present in the output spectrum that is not present at the input and may or may not be a harmonic.

TOTAL HARMONIC DISTORTION (THD) is the ratio, expressed in dBc, of the rms total of the first n harmonic

components at the output to the rms level of the input signal frequency as seen at the output. THD is calculated

(1)

where Af1 is the RMS power of the input frequency at the output and Af2 through Afn are the RMS power in the

first n harmonic frequencies.

THROUGHPUT TIME is the minimum time required between the start of two successive conversions. It is the

acquisition time plus the conversion time.

LEAST SIGNIFICANT BIT (LSB) is the bit that has the smallest value or weight of all bits in a word. This value is

LSB = VA/ 2n(2)

Product Folder Links: ADC081C021 ADC081C027

ADC081C021, ADC081C027

www.ti.com

SNAS447C –FEBRUARY 2008–REVISED MARCH 2013

where VAis the supply voltage for this product, and "n" is the resolution in bits, which is 8 for the ADC081C021.

MOST SIGNIFICANT BIT (MSB) is the bit that has the largest value or weight of all bits in a word. Its value is

1/2 of VA.

Product Folder Links: ADC081C021 ADC081C027

ADC081C021, ADC081C027

SNAS447C –FEBRUARY 2008–REVISED MARCH 2013

www.ti.com

Typical Performance Characteristics

fSCL = 400kHz, fSAMPLE = 22ksps, fIN = 1kHz, VA= 5.0V, TA= +25°C, unless otherwise stated.

INL vs. Code - VA=3V DNL vs. Code - VA=3V

Figure 5. Figure 6.

INL vs. Code - VA=5V DNL vs. Code - VA=5V

Figure 7. Figure 8.

INL vs. Supply DNL vs. Supply

Figure 9. Figure 10.

Product Folder Links: ADC081C021 ADC081C027

ADC081C021, ADC081C027

www.ti.com

SNAS447C –FEBRUARY 2008–REVISED MARCH 2013

Typical Performance Characteristics (continued)

fSCL = 400kHz, fSAMPLE = 22ksps, fIN = 1kHz, VA= 5.0V, TA= +25°C, unless otherwise stated.

ENOB vs. Supply SINAD vs. Supply

Figure 11. Figure 12.

FFT Plot - VA=3V FFT Plot - VA=3V

Figure 13. Figure 14.

Offset Error vs. Temperature Gain Error vs. Temperature

Figure 15. Figure 16.

Product Folder Links: ADC081C021 ADC081C027

ADC081C021, ADC081C027

SNAS447C –FEBRUARY 2008–REVISED MARCH 2013

www.ti.com

Typical Performance Characteristics (continued)

fSCL = 400kHz, fSAMPLE = 22ksps, fIN = 1kHz, VA= 5.0V, TA= +25°C, unless otherwise stated.

Continuous Operation Supply Current vs. VAAutomatic Conversion Supply Current vs. VA

Figure 17. Figure 18.

Power Down (PD1) Supply Current vs. VA

Figure 19.

Product Folder Links: ADC081C021 ADC081C027

VIN

AGND

SAMPLING

CAPACITOR

SW1 -

+CONTROL

LOGIC

SW2

VA/2

CHARGE

REDISTRIBUTION

DAC

VIN

AGND

SAMPLING

CAPACITOR

SW1 -

+CONTROL

LOGIC

SW2

VA/2

CHARGE

REDISTRIBUTION

DAC

ADC081C021, ADC081C027

www.ti.com

SNAS447C –FEBRUARY 2008–REVISED MARCH 2013

Functional Description

The ADC081C021 and the ADC081C027 are successive-approximation analog-to-digital converters designed

around a charge-redistribution digital-to-analog converter. Unless otherwise stated, references to the

ADC081C021 in this section will apply to both the ADC081C021 and the ADC081C027.

CONVERTER OPERATION

Simplified schematics of the ADC081C021 in both track and hold operation are shown in Figure 20 and

Figure 21 respectively. In Figure 20, the ADC081C021 is in track mode. SW1 connects the sampling capacitor to

the analog input channel and SW2 equalizes the comparator inputs. The ADC is in this state for approximately

0.4µs at the beginning of every conversion cycle, which begins at the ACK fall of SDA. Conversions occur when

the conversion result register is read and when the ADC is in automatic conversion mode. (see AUTOMATIC

CONVERSION MODE).

Figure 21 shows the ADC081C021 in hold mode. SW1 connects the sampling capacitor to ground and SW2

unbalances the comparator. The control logic then instructs the charge-redistribution DAC to add or subtract

fixed amounts of charge to or from the sampling capacitor until the comparator is balanced. When the

comparator is balanced, the digital word supplied to the DAC is also the digital representation of the analog input

voltage. This digital word is stored in the conversion result register and read via the 2-wire interface.

In the Normal (non-Automatic) Conversion mode, a new conversion is started after the previous conversion result

is read. In the Automatic Mode, conversions are started at set intervals, as determined by bits D7 through D5 of

the Configuration Register. The intent of the Automatic mode is to provide a "watchdog" function to ensure that

the input voltage remains within the limits set in the Alert Limit Registers. The minimum and maximum

conversion results can then be read from the Lowest Conversion Register and the Highest Conversion Register,

as described in INTERNAL REGISTERS.

Figure 20. ADC081C021 in Track Mode Figure 21. ADC081C021 in Hold Mode

ANALOG INPUT

An equivalent circuit for the input of the ADC081C021 is shown in Figure 22. The diodes provide ESD protection

for the analog input. The operating range for the analog input is 0 V to VA. Going beyond this range will cause

the ESD diodes to conduct and result in erratic operation. For this reason, these diodes should NOT be used to

clamp the input signal.

The capacitor C1 in Figure 22 has a typical value of 3 pF and is mainly the package pin capacitance. Resistor R1

is the on resistance (RON) of the multiplexer and track / hold switch and is typically 500Ω. Capacitor C2 is the

ADC081C021 sampling capacitor, and is typically 30 pF. The ADC081C021 will deliver best performance when

driven by a low-impedance source (less than 100Ω). This is especially important when using the ADC081C021 to

sample dynamic signals. A buffer amplifier may be necessary to limit source impedance. Use a precision op-amp

to maximize circuit performance. Also important when sampling dynamic signals is a band-pass or low-pass filter

to reduce noise at the input.

Product Folder Links: ADC081C021 ADC081C027

0V +VA - 1.5 LSB

0.5 LSB ANALOG INPUT

1 LSB = VA/256

ADC CODE

111...111

111...110

111...000

011...111

000...010

000...001

000...000

VIN

30 pF

3 pF

Conversion Phase - Switch Open

Track Phase - Switch Closed

ADC081C021, ADC081C027

SNAS447C –FEBRUARY 2008–REVISED MARCH 2013

www.ti.com

Figure 22. Equivalent Input Circuit

The analog input is sampled for eight internal clock cycles, or for typically 400 ns, after the fall of SDA for

acknowledgement. This time could be as long as about 530 ns. The sampling switch opens and the conversion

begins this time after the fall of ACK. This time are typical at room temperature and may vary with temperature.

ADC TRANSFER FUNCTION

The output format of the ADC081C021 is straight binary. Code transitions occur midway between successive

integer LSB values. The LSB width for the ADC081C021 is VA/ 256. The ideal transfer characteristic is shown in

Figure 23. The transition from an output code of 0000 0000 0000 to a code of 0000 0000 0001 is at 1/2 LSB, or a

voltage of VA/ 512. Other code transitions occur at intervals of 1 LSB.

Figure 23. Ideal Transfer Characteristic

REFERENCE VOLTAGE

The ADC081C021 uses the supply (VA) as the reference, so VAmust be treated as a reference. The analog-to-

digital conversion will only be as precise as the reference (VA), so the supply voltage should be free of noise. The

reference should be driven by a low output impedance voltage source.

The Applications section provides recommended ways to provide the supply voltage appropriately. Refer to

TYPICAL APPLICATION CIRCUIT for details.

Product Folder Links: ADC081C021 ADC081C027

SDA

SCL

I2C Serial Interface

Conversion Result

Pointer = 00000000

Pointer

(selects

read from

or write to)

Pointer Address

Highest Conversion

Pointer = 00000111

Lowest Conversion

Pointer = 00000110

Configuration

Pointer = 00000010

Alert Status

Pointer = 00000001

Hysteresis

Pointer = 00000101

High Limit

Pointer = 00000100

Low Limit

Pointer = 00000011

Data

ADC081C021, ADC081C027

www.ti.com

SNAS447C –FEBRUARY 2008–REVISED MARCH 2013

POWER-ON RESET

An internal power-on reset (POR) occurs when the supply voltage transitions above the power-on reset

threshold. Each of the registers contains a defined value upon POR and this data remains there until any of the

following occurs:

• The first conversion is completed, causing the Conversion Result and Status registers to be updated.

• A different data word is written to a writeable register.

• The ADC is powered down.

The internal registers will lose their contents if the supply voltage goes below 2.4V. Should this happen, it is

important that the VAsupply be lowered to a maximum of 200mV before the supply is raised again to properly

reset the device and ensure that the ADC performs as specified.

INTERNAL REGISTERS

The ADC081C021 has 8 internal data registers and one address pointer. The registers provide additional ADC

functions such as storing minimum and maximum conversion results, setting alert threshold levels, and storing

data to configure the operation of the device. Figure 24 shows all of the registers and their corresponding

address pointer values. All of the registers are read/write capable except the conversion result register which is

read-only.

Figure 24. Register Structure

Product Folder Links: ADC081C021 ADC081C027

ADC081C021, ADC081C027

SNAS447C –FEBRUARY 2008–REVISED MARCH 2013

www.ti.com

Address Pointer Register

The address pointer determines which of the data registers is accessed by the I2C interface. The first data byte

of every write operation is stored in the address pointer register. This value selects the register that the following

data bytes will be written to or read from. Only the three LSBs of this register are variable. The other bits must

always be written to as zeros. After a power-on reset, the pointer register defaults to all zeros (conversion result

Default Value: 00h

P7 P6 P5 P4 P3 P2 P1 P0

0 0 0 0 0 Register Select

P2 P1 P0 REGISTER

0 0 0 Conversion Result (read only)

0 0 1 Alert Status (read/write)

0 1 0 Configuration (read/write)

0 1 1 Low Limit (read/write)

1 0 0 High Limit (read/write)

1 0 1 Hysteresis (read/write)

1 1 0 Lowest Conversion (read/write)

1 1 1 Highest Conversion (read/write)

Conversion Result Register

This register holds the result of the most recent conversion. In the normal mode, a new conversion is started

whenever this register is read. The conversion result data is in straight binary format with the MSB at D11.

Pointer Address 00h (Read Only)

Default Value: 0000h

D15 D14 D13 D12 D11 D10 D9 D8

Alert Flag Reserved Conversion Result [7:4]

D7 D6 D5 D4 D3 D2 D1 D0

Conversion Result [3:0] Reserved

Bits Name Description

15 Alert Flag This bit indicates when an alert condition has occurred. When the Alert Bit Enable is set in the

Configuration Register, this bit will be high if either alert flag is set in the Alert Status Register.

Otherwise, this bit is a zero. The I2C controller will typically read the Alert Status register and other data

registers to determine the source of the alert.

14:12 Reserved Always reads zeros.

11:4 Conversion Result The Analog-to-Digital conversion result. The Conversion result data is a 8-bit data word in straight

binary format. The MSB is D11.

3:0 Reserved Always reads zeros.

Product Folder Links: ADC081C021 ADC081C027

ADC081C021, ADC081C027

www.ti.com

SNAS447C –FEBRUARY 2008–REVISED MARCH 2013

Alert Status Register

This register indicates if a high or a low threshold has been violated. The bits of this register are active high. That

is, a high indicates that the respective limit has been violated.

Pointer Address 01h (Read/Write)

Default Value: 00h

D7 D6 D5 D4 D3 D2 D1 D0

Reserved Over Range Under Range

Alert Alert

Bits Name Description

7:2 Reserved Always reads zeros. Zeros must be written to these bits.

1 Over Range Bit is set to 1 when the measured voltage exceeds the VHIGH limit stored in the programmable VHIGH

Alert Flag limit register. Flag is reset to 0 when one of the following two conditions is met: (1) The controller writes

a one to this bit. (2) The measured voltage decreases below the programmed VHIGH limit minus the

programmed VHYST value (See Figure 27) . The alert will only self-clear if the Alert Hold bit is cleared in

the Configuration register. If the Alert Hold bit is set, the only way to clear an over range alert is to write

a one to this bit.

0 Under Range Bit is set to 1 when the measured voltage falls below the VLOW limit stored in the programmable VLOW

Alert Flag limit register. Flag is reset to 0 when one of the following two conditions is met: (1) The controller writes

a one to this bit. (2) The measured voltage increases above the programmed VLOW limit plus the

programmed VHYST value. The alert will only self-clear if the Alert Hold bit is cleared in the

Configuration register. If the Alert Hold bit is set, the only way to clear an under range alert is to write a

one to this bit.

Configuration Register

Pointer Address 02h (Read/Write)

Default Value: 00h

D7 D6 D5 D4 D3 D2 D1 D0

Cycle Time [2:0] Alert Hold Alert Flag Enable Alert Pin Enable 0 Polarity

Cycle Time[2:0] Conversion Typical fconvert

Interval (ksps)

D7 D6 D5

0 0 0 Mode Disabled 0

0 0 1 Tconvert x 32 27

0 1 0 Tconvert x 64 13.5

0 1 1 Tconvert x 128 6.7

1 0 0 Tconvert x 256 3.4

1 0 1 Tconvert x 512 1.7

1 1 0 Tconvert x 1024 0.9

1 1 1 Tconvert x 2048 0.4

Product Folder Links: ADC081C021 ADC081C027

ADC081C021, ADC081C027

SNAS447C –FEBRUARY 2008–REVISED MARCH 2013

www.ti.com

Bits Name Description

7:5 Cycle Time Configures Automatic Conversion mode. When these bits are set to zeros, the automatic conversion

mode is disabled. This is the case at power-up.

When these bits are set to a non-zero value, the ADC will begin operating in automatic conversion

mode. (See AUTOMATIC CONVERSION MODE). The Cycle Time table shows how different values

provide various conversion intervals.

4 Alert Hold 0: Alerts will self-clear when the measured voltage moves within the limits by more than the hysteresis

1: Alerts will not self-clear and are only cleared when a one is written to the alert high flag or the alert

low flag in the Alert Status register.

3 Alert Flag Enable 0: Disables alert status bit [D15] in the Conversion Result register.

1: Enables alert status bit [D15] in the Conversion Result register.

2 Alert Pin Enable 0: Disables the ALERT output pin. The ALERT output will TRI-STATE when the pin is disabled.

1: Enables the ALERT output pin.

*This bit does not apply to the ADC081C027.

1 Reserved Always reads zeros. Zeros must be written to these bits.

0 Polarity This bit configures the active level polarity of the ALERT output pin.

0: Sets the ALERT pin to active low.

1: Sets the ALERT pin to active high.

*This bit does not apply to the ADC081C027.

VLOW -- Alert Limit Register - Under Range

This register holds the lower limit threshold used to determine the alert condition. If the conversion moves lower

than this limit, a VLOW alert is generated.

Pointer Address 03h (Read/Write)

Default Value: 0000h

D15 D14 D13 D12 D11 D10 D9 D8

Reserved VLOW Limit [7:4]

D7 D6 D5 D4 D3 D2 D1 D0

VLOW Limit [3:0] Reserved

Bits Name Description

15:12 Reserved Always reads zeros. Zeros must be written to these bits.

11:4 VLOW Limit Sets the lower limit threshold used to determine the alert condition. If the conversion moves lower than

this limit, a VLOW alert is generated.

3:0 Reserved Always reads zeros. Zeros must be written to these bits.

VHIGH -- Alert Limit Register - Over Range

This register holds the upper limit threshold used to determine the alert condition. If the conversion moves higher

than this limit, a VHIGH alert is generated.

Pointer Address 04h (Read/Write)

Default Value: 0FFFh

D15 D14 D13 D12 D11 D10 D9 D8

Reserved VHIGH Limit [7:4]

D7 D6 D5 D4 D3 D2 D1 D0

VHIGH Limit [3:0] Reserved

Product Folder Links: ADC081C021 ADC081C027

ADC081C021, ADC081C027

www.ti.com

SNAS447C –FEBRUARY 2008–REVISED MARCH 2013

Bits Name Description

15:12 Reserved Always reads zeros. Zeros must be written to these bits.

11:4 VHIGH Limit Sets the upper limit threshold used to determine the alert condition. If the conversion moves higher

than this limit, a VHIGH alert is generated.

3:0 Reserved Always reads zeros. Zeros must be written to these bits.

VHYST -- Alert Hysteresis Register

This register holds the hysteresis value used to determine the alert condition. After a VHIGH or VLOW alert occurs,

the conversion result must move within the VHIGH or VLOW limit by more than this value to clear the alert

condition. Note: If the Alert Hold bit is set in the configuration register, alert conditions will not self-clear.

Pointer Address 05h (Read/Write)

Default Value: 0000h

D15 D14 D13 D12 D11 D10 D9 D8

Reserved Hysteresis [7:4]

D7 D6 D5 D4 D3 D2 D1 D0

Hysteresis [3:0] Reserved

Bits Name Description

15:12 Reserved Always reads zeros. Zeros must be written to these bits.

11:4 Hysteresis Hysteresis value. D11 is MSB.

3:0 Reserved Always reads zeros. Zeros must be written to these bits.

VMIN -- Lowest Conversion Register

This register holds the Lowest Conversion result when in the automatic conversion mode. Each conversion result

is compared against the contents of this register. If the value is lower, it becomes the lowest conversion and

replaces the current value. If the value is higher, the register contents remain unchanged. The lowest conversion

value can be cleared at any time by writing 0FFFh to this register. The value of this register will update

automatically when the automatic conversion mode is enabled, but is NOT updated in the normal mode.

Pointer Address 06h (Read/Write)

Default Value: 0FFFh

D15 D14 D13 D12 D11 D10 D9 D8

Reserved Lowest Conversion [7:4]

D7 D6 D5 D4 D3 D2 D1 D0

Lowest Conversion [3:0] Reserved

Bits Name Description

15:12 Reserved Always reads zeros. Zeros must be written to these bits.

11:4 Lowest Conversion Lowest conversion result data. D11 is MSB.

3:0 Reserved Always reads zeros. Zeros must be written to these bits.

Product Folder Links: ADC081C021 ADC081C027

ADC081C021, ADC081C027

SNAS447C –FEBRUARY 2008–REVISED MARCH 2013

www.ti.com

VMAX -- Highest Conversion Register

This register holds the Highest Conversion result when in the Automatic mode. Each conversion result is

compared against the contents of this register. If the value is higher, it replaces the previous value. If the value is

lower, the register contents remain unchanged. The highest conversion value can be cleared at any time by

writing 0000h to this register. The value of this register will update automatically when the automatic conversion

mode is enabled, but is NOT updated in the normal mode.

Pointer Address 07h (Read/Write)

Default Value: 0000h

D15 D14 D13 D12 D11 D10 D9 D8

Reserved Highest Conversion [7:4]

D7 D6 D5 D4 D3 D2 D1 D0

Highest Conversion [3:0] Reserved

Bits Name Description

15:12 Reserved Always reads zeros. Zeros must be written to these bits.

11:4 Highest Conversion Highest conversion result data. D11 is MSB.

3:0 Reserved Always reads zeros. Zeros must be written to these bits.

SERIAL INTERFACE

The I2C-compatible interface operates in all three speed modes. Standard mode (100kHz) and Fast mode

(400kHz) are functionally the same and will be referred to as Standard-Fast mode in this document. High-Speed

mode (3.4MHz) is an extension of Standard-Fast mode and will be referred to as Hs-mode in this document.

The following diagrams describe the timing relationships of the clock (SCL) and data (SDA) signals. Pull-up

resistors or current sources are required on the SCL and SDA busses to pull them high when they are not being

driven low. A logic zero is transmitted by driving the output low. A logic high is transmitted by releasing the output

and allowing it to be pulled-up externally. The appropriate pull-up resistor values will depend upon the total bus

capacitance and operating speed. The ADC081C021 offers extended ESD tolerance (8kV HBM) for the I2C bus

pins (SCL & SDA) allowing extension of the bus across multiple boards without extra ESD protection.

Basic I2C Protocol

The I2C interface is bi-directional and allows multiple devices to operate on the same bus. The bus consists of

master devices and slave devices which can communicate back and forth over the I2C interface. Master devices

control the bus and are typically microcontrollers, FPGAs, DSPs, or other digital controllers. Slave devices are

controlled by a master and are typically peripheral devices such as the ADC081C021. To support multiple

devices on the same bus, each slave has a unique hardware address which is referred to as the "slave address."

To communicate with a particular device on the bus, the controller (master) sends the slave address and listens

for a response from the slave. This response is referred to as an acknowledge bit. If a slave on the bus is

addressed correctly, it acknowledges (ACKs) the master by driving the SDA bus low. If the address doesn't

match a device's slave address, it not-acknowledges (NACKs) the master by letting SDA be pulled high. ACKs

also occur on the bus when data is being transmitted. When the master is writing data, the slave ACKs after

every data byte is successfully received. When the master is reading data, the master ACKs after every data

byte is received to let the slave know it wants to receive another data byte. When the master wants to stop

reading, it NACKs after the last data byte and creates a stop condition on the bus.

All communication on the bus begins with either a Start condition or a Repeated Start condition. The protocol for

starting the bus varies between Standard-Fast mode and Hs-mode. In Standard-Fast mode, the master

generates a Start condition by driving SDA from high to low while SCL is high. In Hs-mode, starting the bus is

more complicated. Please refer to High-Speed (Hs) Mode for the full details of a Hs-mode Start condition.

A Repeated Start is generated to address a different device or register, or to switch between read and write

modes. The master generates a Repeated Start condition by driving SDA low while SCL is high. Following the

Repeated Start, the master sends out the slave address and a read/write bit as shown in Figure 25. The bus

continues to operate in the same speed mode as before the Repeated Start condition.

Product Folder Links: ADC081C021 ADC081C027

SCL

SDA

START or

REPEATED

START

STOP

1 2 6 7 891 2 89

MSB

7-bit Slave Address R/W

Direction

BitAcknowledge

from the Device

MSB

Data Byte

*Acknowledge

or Not-ACK

ACK N/ACK

Repeated for the Lower Data Byte

and Additional Data Transfers

LSB LSB

*Note: In continuous mode, this bit must be an ACK from

the data receiver. Immediately preceding a STOP

condition, this bit must be a NACK from the master.

ADC081C021, ADC081C027

www.ti.com

SNAS447C –FEBRUARY 2008–REVISED MARCH 2013

All communication on the bus ends with a Stop condition. In either Standard-Fast mode or Hs-Mode, a Stop

condition occurs when SDA is pulled high while SCL is high. After a Stop condition, the bus remains idle until a

master generates another Start condition.

Please refer to the Philips I2C®Specification (Version 2.1 Jan, 2000) for a detailed description of the serial

interface.

Figure 25. Basic Operation.

Standard-Fast Mode

In Standard-Fast mode, the master generates a start condition by driving SDA from high to low while SCL is

high. The start condition is always followed by a 7-bit slave address and a Read/Write bit. After these 8 bits have

been transmitted by the master, SDA is released by the master and the ADC081C021 either ACKs or NACKs the

address. If the slave address matches, the ADC081C021 ACKs the master. If the address doesn't match, the

ADC081C021 NACKs the master.

For a write operation, the master follows the ACK by sending the 8-bit register address pointer to the ADC. Then

the ADC081C021 ACKs the transfer by driving SDA low. Next, the master sends the upper 8-bits to the

ADC081C021. Then the ADC081C021 ACKs the transfer by driving SDA low. For a single byte transfer, the

master should generate a stop condition at this point. For a 2-byte write operation, the lower 8-bits are sent by

the master. The ADC081C021 then ACKs the transfer, and the master either sends another pair of data bytes,

generates a Repeated Start condition to read or write another register, or generates a Stop condition to end

communication.

Aread operation can take place either of two ways:

If the address pointer is pre-set before the read operation, the desired register can be read immediately following

the slave address. In this case, the upper 8-bits of the register, set by the pre-set address pointer, are sent out

by the ADC. For a single byte read operation, the Master sends a NACK to the ADC and generates a Stop

condition to end communication after receiving 8-bits of data. For a 2-Byte read operation, the Master continues

the transmission by sending an ACK to the ADC. Then, the ADC sends out the lower 8-bits of the ADC register.

At this point, the master either sends; an ACK to receive more data or, a NACK followed by a Stop or Repeated

Start. If the master sends an ACK, the ADC sends the next upper data byte, and the read cycle repeats.

If the ADC081S021 address pointer needs to be set, the master needs to write to the device and set the address

pointer before reading from the desired register. This type of read requires a start, the slave address, a write bit,

the address pointer, a Repeated Start (if appropriate), the slave address, and a read bit (refer to Figure 30).

Following this sequence, the ADC sends out the upper 8-bits of the register. For a single byte read operation, the

Master must then send a NACK to the ADC and generate a Stop condition to end communication. For a 2-Byte

write operation, the Master sends an ACK to the ADC. Then, the ADC sends out the lower 8-bits of the ADC

Repeated Start. If the master sends an ACK, the ADC sends another pair of data bytes, and the read cycle will

repeat. The number of data words that can be read is unlimited.

Product Folder Links: ADC081C021 ADC081C027

SCL

SDA

START

1 2 6 7 89

8-ELW0DVWHUFRGH³00001[[[´

Not-Acknowledge

from the Device

NACK

Standard-Fast Mode Hs-Mode

Repeated

START

1 2

MSB

7-bit Slave

Address

ADC081C021, ADC081C027

SNAS447C –FEBRUARY 2008–REVISED MARCH 2013

www.ti.com

High-Speed (Hs) Mode

For Hs-mode, the sequence of events to begin communication differs slightly from Standard-Fast mode.

Figure 26 describes this in further detail. Initially, the bus begins running in Standard-Fast mode. The master

generates a Start condition and sends the 8-bit Hs master code (00001XXX) to the ADC081C021. Next, the

ADC081C021 responds with a NACK. Once the SCL line has been pulled to a high level, the master switches to

Hs-mode by increasing the bus speed and generating a second Repeated Start condition (driving SDA low while

SCL is pulled high). At this point, the master sends the slave address to the ADC081C021, and communication

continues as shown above in the "Basic Operation" Diagram (see Figure 25).

When the master generates a Repeated Start condition while in Hs-mode, the bus stays in Hs-mode awaiting the

slave address from the master. The bus continues to run in Hs-mode until a Stop condition is generated by the

master. When the master generates a Stop condition on the bus, the bus must be started in Standard-Fast mode

again before increasing the bus speed and switching to Hs-mode.

Figure 26. Beginning Hs-Mode Communication

I2C Slave (Hardware) Address

The ADC has a seven-bit hardware address which is also referred to as a slave address. For the VSSOP-8

version of the ADC081C021, this address is configured by the ADR0 and ADR1 addres selection inputs. For the

ADC081C027, the address is configured by the ADR0 address selection input. ADR0 and ADR1 can be

grounded, left floating, or tied to VA. If desired, ADR0 can be set to VA/2 rather than left floating. The state of

these inputs sets the hardware address that the ADC responds to on the I2C bus (see Table 2). For the SOT-6

version of the ADC081C021, the hardware address is not pin-configurable and is set to 1010100. The diagrams

in COMMUNICATING WITH THE ADC081C021 describe how the I2C controller should address the ADC via the

I2C interface.

Pin compatible alternatives that provide additional address options to the SOT-6 version of the ADC081C021 and

the ADC081C027 are available.

Table 2. Slave Addresses

ADC081C027 ADC081C021 ADC081C021

(SOT-6) (SOT-6) (VSSOP-8)

Slave Address

[A6 - A0] ADR0 ALERT ADR1 ADR0

1010000 Floating ----------------- Floating Floating

1010001 GND ----------------- Floating GND

1010010 VA----------------- Floating VA

1010100 ----------------- Single Address GND Floating

1010101 ----------------- ----------------- GND GND

1010110 ----------------- ----------------- GND VA

1011000 ----------------- ----------------- VAFloating

1011001 ----------------- ----------------- VAGND

1011010 ----------------- ----------------- VAVA

Product Folder Links: ADC081C021 ADC081C027

TIME

VOLTAGE

VHIGH Limit

VHIGH - VHYST

ALERT pin

(Active Low)

Measured Voltage

Over Range Alert

)ODJVHWWR³1´

TIME

VOLTAGE

Measured Voltage

VHIGH Limit

VHIGH - VHYST

ALERT pin

(Active Low)

ADC081C021, ADC081C027

www.ti.com

SNAS447C –FEBRUARY 2008–REVISED MARCH 2013

ALERT FUNCTION

The ALERT function is an "out-of-range" indicator. At the end of every conversion, the measured voltage is

compared to the values in the VHIGH and VLOW registers. If the measured voltage exceeds the value stored in

VHIGH or falls below the value stored in VLOW, an alert condition occurs. The Alert condition is indicated in up to

three places. First, the alert condition always causes either or both of the alert flags in the Alert Status register to

go high. If the measured voltage exceeds the VHIGH limit, the Over Range Alert Flag is set. If the measured

voltage falls below the VLOW limit, the Under Range Alert Flag is set. Second, if the Alert Flag Enable bit is set in

the Configuration register, the alert condition also sets the MSB of the Conversion Result register. Third, if the

Alert Pin Enable bit is set in the Configuration register, the ALERT output becomes active (see Figure 27). The

ALERT output (ADC081S021 only) can be configured as an active high or active low output via the Polarity bit in

the Configuration register. If the Polarity bit is cleared, the ALERT output is configured as active low. If the

Polarity bit is set, the ALERT output is configured as active high.

The Over Range Alert condition is cleared when one of the following two conditions is met:

1. The controller writes a one to the Over Range Alert Flag bit.

2. The measured voltage goes below the programmed VHIGH limit minus the programmed VHYST value and the

Alert Hold bit is cleared in the Configuration register. (see Figure 27). If the Alert Hold bit is set, the alert

condition persists and only clears when a one is written to the Over Range Alert Flag bit.

The Under Range Alert condition is cleared when one of the following two conditions is met:

1. The controller writes a one to the Under Range Alert Flag bit.

2. The measured voltage goes above the programmed VLOW limit plus the programmed VHYST value and the

Alert Hold bit is cleared in the Configuration register. If the Alert Hold bit is set, the alert condition persists

and only clears when a one is written to the Under Range Alert Flag bit.

If the alert condition has been cleared by writing a one to the alert flag while the measured voltage still violates

the VHIGH or VLOW limits, an alert condition will occur again after the completion of the next conversion (see

Figure 28).

Alert conditions only occur if the input voltage exceeds the VHIGH limit or falls below the VLOW limit at the sample-

hold instant. The input voltage can exceed the VHIGH limit or fall below the VLOW limit briefly between conversions

without causing an alert condition.

Figure 27. Alert condition cleared when measured voltage crosses VHIGH - VHYST

Figure 28. Alert condition cleared by writing a "1" to the Alert Flag.

Product Folder Links: ADC081C021 ADC081C027

D7 D6 D5 D4 D3 D2 D1 D0

1 9 1 9

ACK

ADC

Start by

Master N/ACK*

Master

SCL

SDA Stop

Master

1 9

D15 D14 D13 D12 D11 D10 D9 D8 ACK

Master

Frame 1

Address Byte

from Master

Frame 2

Data Byte from

ADC

Frame 3

Data Byte from

ADC

R/W

A2 A0A1

A3A4A5A6

Repeat Frames

2 & 3 for

Continuous Mode

*Note: In continuous mode, this bit must be an ACK. Immediately

preceding a STOP condition, this bit must be a NACK.

ADC081C021, ADC081C027

SNAS447C –FEBRUARY 2008–REVISED MARCH 2013

www.ti.com

AUTOMATIC CONVERSION MODE

The automatic conversion mode configures the ADC to continually perform conversions without receiving "read"

instructions from the controller over the I2C interface. The mode is activated by writing a non-zero value into the

Cycle Time bits - D[7:5] - of the Configuration register (see Configuration Register). Once the ADC081C021

enters this mode, the internal oscillator is always enabled. The ADC's control logic samples the input at the

sample rate set by the cycle time bits. Although the conversion result is not transmitted by the 2-wire interface, it

is stored in the conversion result register and updates the various status registers of the device.

In automatic conversion mode, the out-of-range alert function is active and updates after every conversion. The

ADC can operate independently of the controller in automatic conversion mode. When the input signal goes "out-

of-range", an alert signal is sent to the controller. The controller can then read the status registers and determine

the source of the alert condition. Also, comparison and updating of the VMIN and VMAX registers occurs after every

conversion in automatic conversion mode. The controller can occasionally read the VMIN and/or VMAX registers to

determine the sampled input extremes. These register values persist until the user resets the VMIN and VMAX

registers. These two features are useful in system monitoring, peak detection, and sensing applications.

COMMUNICATING WITH THE ADC081C021

The ADC081C021's data registers are selected by the address pointer (see Address Pointer Register). To

read/write a specific data register, the pointer must be set to that register's address. The pointer is always written

at the beginning of a write operation. When the pointer needs to be updated for a read cycle, a write operation

must precede the read operation to set the pointer address correctly. On the other hand, if the pointer is preset

correctly, a read operation can occur without writing the address pointer register. The following timing diagrams

describe the various read and write operations supported by the ADC.

Reading from a 2-Byte ADC Register

The following diagrams indicate the sequence of actions required for a 2-Byte read from an ADC081C021

Figure 29. (a) Typical Read from a 2-Byte ADC Register with Preset Pointer

Product Folder Links: ADC081C021 ADC081C027

1 9 1 9

Ack

ADC

Start by

Master

R/W Ack

ADC

Frame 1

Address Byte

from Master

Frame 2

Pointer Byte

from Master

0 0 0 0 P2 P1 P0

D7 D6 D5 D4 D3 D2 D1 D0

1 9

ACK

ADC

NACK

Master

Stop

Master

1 9

Frame 3

Address Byte

from Master

Frame 4

Data Byte from

ADC

R/W

A2 A0A1

A3A4A5A6

Repeat

Start by

Master

A2 A0A1A3A4A5A6

SCL

SDA 0

SCL

(continued)

SDA

(continued)

D7 D6 D5 D4 D3 D2 D1 D0

1 9

ACK

ADC

Start by

Master NACK

Master

SCL

SDA Stop

Master

1 9

Frame 1

Address Byte

from Master

Frame 2

Data Byte from

ADC

R/W

A2 A0A1

A3A4A5A6

1 9 1 9

Ack

ADC

Start by

Master

R/W Ack

ADC

Frame 1

Address Byte

from Master

Frame 2

Pointer Byte

from Master

0 0 0 0 P2 P1 P0

D7 D6 D5 D4 D3 D2 D1 D0

1 9 1 9

ACK

ADC

N/ACK*

Master

Stop

Master

1 9

D15 D14 D13 D12 D11 D10 D9 D8 ACK

Master

Frame 3

Address Byte

from Master

Frame 4

Data Byte from

ADC

Frame 5

Data Byte from

ADC

R/W

A2 A0A1

A3A4A5A6

Repeat Frames

4 & 5 for

Continuous Mode

*Note: In continuous mode, this bit must be an ACK. Immediately

preceding a STOP condition, this bit must be a NACK.

Repeat

Start by

Master

A2 A0A1A3A4A5A6

SCL

SDA 0

SCL

(continued)

SDA

(continued)

ADC081C021, ADC081C027

www.ti.com

SNAS447C –FEBRUARY 2008–REVISED MARCH 2013

Figure 30. (b) Typical Pointer Set Followed by Immediate Read of a 2-Byte ADC Register

Reading from a 1-Byte ADC Register

The following diagrams indicate the sequence of actions required for a single Byte read from an ADC081C021

Figure 31. (a) Typical Read from a 1-Byte ADC Register with Preset Pointer

Figure 32. (b) Typical Pointer Set Followed by Immediate Read of a 1-Byte ADC Register

Product Folder Links: ADC081C021 ADC081C027

1 9 1 9

Ack

ADC

Start by

Master

R/W Ack

ADC

Frame 1

Address Byte

from Master

Frame 2

Pointer Byte

from Master

0 0 0 0 P2 P1 P0

D7 D6 D5 D4 D3 D2 D1 D0

1 9

ACK

ADC

NACK

Master

Stop

Master

1 9

Frame 3

Data Byte

from Master

Frame 4

Data Byte

from Master

A2 A0A1A3A4A5A6

SCL

SDA 0

SCL

(continued)

SDA

(continued) D15 D14 D13 D12 D11 D10 D9 D8

1 9 1 9

Start by

Master

R/W

Frame 1

Address Byte

from Master

D7 D6 D5 D4 D3 D2 D1 D0

1 9

Frame 3

Data Byte

from Master

Stop by

Master

SCL

SDA

Frame 2

Pointer Byte

from Master

ACK

ADC

ACK

ADC

ACK

ADC

A2 A0A1

A3A4A5A6 0 0 0 0 P2 P1 P00

ADC081C021, ADC081C027

SNAS447C –FEBRUARY 2008–REVISED MARCH 2013

www.ti.com

Writing to an ADC Register

The following diagrams indicate the sequence of actions required for writing to an ADC081C021 Register.

Figure 33. (a) Typical Write to a 1-Byte ADC Register

Figure 34. (b) Typical Write to a 2-Byte ADC Register

QUIET INTERFACE MODE

To improve performance at High Speed, operate the ADC in Quiet Interface Mode. This mode provides improved

INL and DNL performance in I2C Hs-Mode (3.4MHz). The Quiet Interface mode provides a maximum throughput

rate of 162ksps. Figure 35 describes how to read the conversion result register in this mode. Basically, the

Master needs to release SCL for at least 1µs before the MSB of every upper data byte. The diagram assumes

that the address pointer register is set to its default value.

Quiet Interface mode will only improve INL and DNL performance in Hs-Mode. Standard and Fast mode

performance is unaffected by the Quiet Interface mode.

Product Folder Links: ADC081C021 ADC081C027

1 9

ACK

ADC

Start by

Master

R/W

ACK

Master

Frame 1

Address Byte

from Master

D7 D6 D5 D4 D3 D2 D1 D0

1 9

NACK

Master

Stop

Master

1 9

D15 D14 D13 D12 D11 D10 D9 D8 ACK

Master

Frame 4

Upper Data Byte

from ADC

Frame 5

Lower Data Byte

from ADC

Repeat Frames

4 and 5 for

Continuous Mode

A2 A0A1A3A4A5A6

SCL

SDA

SCL

(continued)

SDA

(continued) D7 D6 D5 D4 D3 D2 D1 D0

1 9

D15 D14 D13 D12 D11 D10 D9 D8 ACK

Master

Frame 2

Upper Data Byte

from ADC

Frame 3

Lower Data Byte

from ADC

Interface Delay

tQuiet 8 1us

Interface Delay

tQuiet 8 1us

ADC081C021, ADC081C027

www.ti.com

SNAS447C –FEBRUARY 2008–REVISED MARCH 2013

Figure 35. Reading in Quiet Interface Mode

Product Folder Links: ADC081C021 ADC081C027

VIN

SCL

SDA

ADC081C021

0.1 PF

GND

4.7 PF

22:

INPUT

470 pF

ALERT

5 k:RPRP

Regulated Supply

VDD

Controller

SCL

SDA

INTERRUPT

I2C BUS ...

ADC081C021, ADC081C027

SNAS447C –FEBRUARY 2008–REVISED MARCH 2013

www.ti.com

APPLICATIONS INFORMATION

TYPICAL APPLICATION CIRCUIT

A typical application circuit is shown in Figure 36. The analog supply is bypassed with a capacitor network

located close to the ADC081C021. The ADC uses the analog supply (VA) as its reference voltage, so it is very

important that VAbe kept as clean as possible. Due to the low power requirements of the ADC081C021, it is

possible to use a precision reference as a power supply.

The bus pull-up resistors (RP) should be powered by the controller's supply. It is important that the pull-up

resistors are pulled to the same voltage potential as VA. This will ensure that the logic levels of all devices on the

bus are compatible. If the controller's supply is noisy, an appropriate bypass capacitor should be added between

the controller's supply pin and the pull-up resistors. For Hs-mode applications, this bypass capacitance will

improve the accuracy of the ADC.

The value of the pull-up resistors (RP) depends upon the characteristics of each particular I2C bus. The I2C

specification describes how to choose an appropriate value. As a general rule-of-thumb, we suggest using a 1kΩ

resistor for Hs-mode bus configurations and a 5kΩresistor for Standard or Fast Mode bus configurations.

Depending upon the bus capacitance, these values may or may not be sufficient to meet the timing requirements

of the I2C bus specification. Please see the I2C specification for further information.

Figure 36. Typical Application Circuit

BUFFERED INPUT

A buffered input application circuit is shown in Figure 37. The analog input is buffered by a TI LMP7731. The

non-inverting amplifier configuration provides a buffered gain stage for a single ended source. This application

circuit is good for single-ended sensor interface. The input must have a DC bias level that keeps the ADC input

signal from swinging below GND or above the supply (+5V in this case).

The LM4132, with its 0.05% accuracy over temperature, is an excellent choice as a reference source for the

ADC081C021.

Product Folder Links: ADC081C021 ADC081C027

TIME

VOLTAGE

Measured

Battery

Voltage

VLOW Limit

ALERT pin

(Active Low)

DISCHARGE CYCLE

VIN SCL

GND

ADC081C021

REF

[LP2980-2.8] R

120 nF

20 kÖ

SDA

ALERT

Low

Battery

Indicator

VBATT

To Controller...

20 kÖ

TIME

VOLTAGE

Measured

Battery

Voltage

VHigh Limit

ALERT pin

(Active Low)

RECHARGE CYCLE

VIN

SCL

SDA

ADDR

ADC081C027

0.1 PF

GND

4.7 PF

INPUT

Unregulated

Supply

LMP7731

LM4132

4.7 PF

ADC081C021, ADC081C027

www.ti.com

SNAS447C –FEBRUARY 2008–REVISED MARCH 2013

Figure 37. Buffered Input Circuit

INTELLIGENT BATTERY MONITOR

The ADC081C021 is easily used as an intelligent battery monitor. The simple circuit shown in Figure 38, uses

the ADC081C021, the LP2980 fixed reference, and a resistor divider to implement an intelligent battery monitor

with a window supervisory feature. The window supervisory feature is implemented by the "out of range" alert

function. When the battery is recharging, the Over Range Alert will indicate that the charging cycle is complete

(see Figure 39). When the battery is nearing depletion, the Under Range Alert will indicate that the battery is low

(see Figure 40).

Figure 38. Intelligent Battery Monitor Circuit Figure 39. Recharge Cycle

Figure 40. Discharge Cycle

In addition to the window supervisory feature, the ADC081C021 will allow the controller to read the battery

voltage at any time during operation.

Product Folder Links: ADC081C021 ADC081C027

TIME

VOLTAGE

Measured

Battery Voltage

VLOW Limit

ALERT pin

(Active Low)

VLOW+VHYST

ADC081C021, ADC081C027

SNAS447C –FEBRUARY 2008–REVISED MARCH 2013

www.ti.com

The accurate voltage reading and the alert feature will allow a controller to improve the efficiency of a battery-

powered device. During the discharge cycle, the controller can switch to a low-battery mode, safely suspend

operation, or report a precise battery level to the user. During the recharge cycle, the controller can implement an

intelligent recharge cycle, decreasing the charge rate when the battery charge nears capacity.

Trickle Charge Controller

While a battery is discharging, the ADC081C021 can be used to control a trickle charge to keep the battery near

full capacity (see Figure 41). When the alert output is active, the battery will recharge. An intelligent recharge

cycle will prevent over-charging and damaging the battery. With a trickle charge, the battery powered device can

be disconnected from the charger at any time with a full charge.

Figure 41. Trickle Charge

LAYOUT, GROUNDING, AND BYPASSING

For best accuracy and minimum noise, the printed circuit board containing the ADC081C021 should have

separate analog and digital areas. The areas are defined by the locations of the analog and digital power planes.

Both of these planes should be located on the same board layer. A single, solid ground plane is preferred if

digital return current does not flow through the analog ground area. Frequently a single ground plane design will

utilize a "fencing" technique to prevent the mixing of analog and digital ground currents. Separate ground planes

should only be utilized when the fencing technique is inadequate. The separate ground planes must be

connected in one place, preferably near the ADC121C021. Special care is required to ensure that signals do not

pass over power plane boundaries. Return currents must always have a continuous return path below their

traces.

The ADC081C021 power supply should be bypassed with a 4.7µF and a 0.1µF capacitor as close as possible to

the device with the 0.1µF right at the device supply pin. The 4.7µF capacitor should be a tantalum type and the

0.1µF capacitor should be a low ESL type. The power supply for the ADC081C021 should only be used for

analog circuits.

Avoid crossover of analog and digital signals and keep the clock and data lines on the component side of the

board. The clock and data lines should have controlled impedances.

Product Folder Links: ADC081C021 ADC081C027

ADC081C021, ADC081C027

www.ti.com

SNAS447C –FEBRUARY 2008–REVISED MARCH 2013

REVISION HISTORY

Changes from Revision B (March 2013) to Revision C Page

• Changed layout of National Data Sheet to TI format .......................................................................................................... 32

Product Folder Links: ADC081C021 ADC081C027

PACKAGE OPTION ADDENDUM

www.ti.com 11-Apr-2013

Addendum-Page 1

PACKAGING INFORMATION

Orderable Device Status

(1)

Package Type Package

Drawing Pins Package

Qty Eco Plan

(2)

Lead/Ball Finish MSL Peak Temp

(3)

Op Temp (°C) Top-Side Markings

(4)

Samples

ADC081C021CIMK/NOPB ACTIVE SOT DDC 6 1000 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 105 X34C

ADC081C021CIMKX/NOPB ACTIVE SOT DDC 6 3000 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 105 X34C

ADC081C021CIMM/NOPB ACTIVE VSSOP DGK 8 1000 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM X36C

ADC081C021CIMMX/NOPB ACTIVE VSSOP DGK 8 3500 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM X36C

ADC081C027CIMK/NOPB ACTIVE SOT DDC 6 1000 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 105 X35C

ADC081C027CIMKX/NOPB ACTIVE SOT DDC 6 3000 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 105 X35C

(1) The marketing status values are defined as follows:

ACTIVE: Product device recommended for new designs.

LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.

NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.

PREVIEW: Device has been announced but is not in production. Samples may or may not be available.

OBSOLETE: TI has discontinued the production of the device.

(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability

information and additional product content details.

TBD: The Pb-Free/Green conversion plan has not been defined.

Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that

lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.

Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between

the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.

Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight

in homogeneous material)

(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

(4) Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a

continuation of the previous line and the two combined represent the entire Top-Side Marking for that device.

PACKAGE OPTION ADDENDUM

www.ti.com 11-Apr-2013

Addendum-Page 2

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information

provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and

continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.

TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device Package

Type Package

Drawing Pins SPQ Reel

Diameter

(mm)

Reel

Width

W1 (mm)

(mm) B0

(mm) K0

(mm) P1

(mm) W

(mm) Pin1

Quadrant

ADC081C021CIMK/NOPB SOT DDC 6 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3

ADC081C021CIMKX/NOP

BSOT DDC 6 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3

ADC081C021CIMM/NOP

BVSSOP DGK 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1

ADC081C021CIMMX/NO

PB VSSOP DGK 8 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1

ADC081C027CIMK/NOPB SOT DDC 6 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3

ADC081C027CIMKX/NOP

BSOT DDC 6 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3

PACKAGE MATERIALS INFORMATION

www.ti.com 26-Mar-2013

Pack Materials-Page 1

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)

ADC081C021CIMK/NOPB SOT DDC 6 1000 210.0 185.0 35.0

ADC081C021CIMKX/NOP

BSOT DDC 6 3000 210.0 185.0 35.0

ADC081C021CIMM/NOPB VSSOP DGK 8 1000 210.0 185.0 35.0

ADC081C021CIMMX/NOP

BVSSOP DGK 8 3500 367.0 367.0 35.0

ADC081C027CIMK/NOPB SOT DDC 6 1000 210.0 185.0 35.0

ADC081C027CIMKX/NOP

BSOT DDC 6 3000 210.0 185.0 35.0

PACKAGE MATERIALS INFORMATION

www.ti.com 26-Mar-2013

Pack Materials-Page 2

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other

changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest

issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and

complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale

supplied at the time of order acknowledgment.

TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms

and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary

to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily

performed.

TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and

applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide

adequate design and operating safeguards.

TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or

other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information

published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or

endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the

third party, or a license from TI under the patents or other intellectual property of TI.

Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration

and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered

documentation. Information of third parties may be subject to additional restrictions.

Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service

voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.

TI is not responsible or liable for any such statements.

Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements

concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support

that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which

anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause

harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use

of any TI components in safety-critical applications.

In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to

help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and

requirements. Nonetheless, such components are subject to these terms.

No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties

have executed a special agreement specifically governing such use.

Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in

military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components

which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and

regulatory requirements in connection with such use.

TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of

non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.

Products Applications

Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive

Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications

Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers

DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps

DSP dsp.ti.com Energy and Lighting www.ti.com/energy

Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial

Interface interface.ti.com Medical www.ti.com/medical

Logic logic.ti.com Security www.ti.com/security

Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense

Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video

RFID www.ti-rfid.com

OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com

Wireless Connectivity www.ti.com/wirelessconnectivity

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265