MIC2205 2MHz PWM Synchronous Buck Regulator with LDO Standby Mode General Description Features The Micrel MIC2205 is a high efficiency 2MHz PWM synchronous buck (step-down) regulator that features a LOWQTM LDO standby mode that draws only 18A of quiescent current. The MIC2205 allows an ultra-low noise, small size, and high efficiency solution for portable power applications. In PWM mode, the MIC2205 operates with a constant frequency 2MHz PWM control. Under light load conditions, such as in system sleep or standby modes, the PWM switching operation can be disabled to reduce switching losses. In this light load LOWQTM mode, the LDO maintains the output voltage and draws only 18A of quiescent current. The LDO mode of operation saves battery life while not introducing spurious noise and high ripple as experienced with pulse skipping or bursting mode regulators. The MIC2205 operates from 2.7V to 5.5V input and features internal power MOSFETs that can supply up to 600mA output current in PWM mode. It can operate with a maximum duty cycle of 100% for use in low-dropout conditions. The MIC2205 is available in the 3mm x 3mm MLF10L package with a junction operating range from -40C to +125C. Data sheets and support documentation can be found on Micrel's web site at www.micrel.com. * 2.7 to 5.5V supply voltage * Light load LOWQTM LDO mode 18A quiescent current Low noise, 75Vrms * 2MHz PWM mode Output current to 600mA >95% efficiency 100% maximum duty cycle * Adjustable output voltage option down to 1V Fixed output voltage options available * Ultra-fast transient response * Stable with 1F ceramic output capacitor * Fully integrated MOSFET switches * Micropower shutdown * Thermal shutdown and current limit protection * Pb-free 3mm x 3mm MLF-10L package * -40C to +125C junction temperature range Applications * Cellular phones * PDAs * USB peripherals ____________________________________________________________________________________________________ Typical Application C1 1F LowQ C2 0.1F 8 VIN SW 9 4 AVIN LDO 2 6 EN FB 5 7 LOWQ 3 BIAS 2.2H VOUT R1 100k R2 125k C3 100pF C4 2.2F PGND AGND GND 10 1 GND VIN = 3V VIN = 3.6V 85 80 VIN = 4.2V 75 70 65 60 55 50 Adjustable Output Buck Regulator with LOWQTM Mode 1.8V OUT Efficiency 100 95 90 EFFICIENCY (%) MIC2205 V IN 2.7V to 5.5V 0 100 200 300 400 500 600 OUTPUT CURRENT (mA) Patent Pending LOWQ is a trademark of Micrel, Inc Micrel, Inc * 2180 Fortune Drive * San Jose, Ca 95131 * USA * tel +1 (408) 944-0800 * fax +1 (408) 474-1000 * http://www.micrel.com April 2005 M9999-041105 www.micrel.com Micrel, Inc. MIC2205 Ordering Information Part Number Output Voltage(1) Junction Temp. Range Package Lead Finish MIC2205-1.3YML 1.3V -40 to +125C 3x3 MLF-10L Pb-free MIC2205-1.38YML 1.38V -40 to +125C 3x3 MLF-10L Pb-free MIC2205-1.5YML 1.5V -40 to +125C 3x3 MLF-10L Pb-free MIC2205-1.58YML 1.58V -40 to +125C 3x3 MLF-10L Pb-free MIC2205-1.8YML 1.8V -40 to +125C 3x3 MLF-10L Pb-free MIC2205-1.85YML 1.85V -40 to +125C 3x3 MLF-10L Pb-free MIC2205YML Adj. -40 to +125C 3x3 MLF-10L Pb-free Note: 1. Other Voltage options available. Contact Micrel for details. Pin Configuration 10 PGND AGND 1 LDO 2 9 SW BIAS 3 8 VIN AVIN 4 7 LOWQ FB 5 EP 6 EN 3mm x 3mm MLF-10L (ML) Pin Description Pin Number Pin Name 1 AGND 2 LDO LDO Output (Output): Connect to VOUT for LDO mode operation. 3 BIAS Internal circuit bias supply. Must be de-coupled to signal ground with a 0.1F capacitor and should not be loaded. 4 AVIN Analog Supply Voltage (Input): Supply voltage for the analog control circuitry and LDO input power. Requires bypass capacitor to GND. 5 FB Feedback. Input to the error amplifier. For the Adjustable option, connect to the external resistor divider network to set the output voltage. For fixed output voltage options, connect to VOUT and an internal resistor network sets the output voltage. 6 EN Enable (Input). Logic low will shut down the device, reducing the quiescent current to less than 5A. 7 _____ LOWQ 8 VIN Supply Voltage (Input): Supply voltage for the internal switches and drivers. 9 SW Switch (Output): Internal power MOSFET output switches. 10 PGND EP GND April 2005 Pin Function Analog (signal) Ground. Enable LDO Mode (Input): Logic low enables the internal LDO and disables the PWM operation. Logic high enables the PWM mode and disables the LDO mode. Power Ground. Ground, backside pad. 2 M9999-041105 www.micrel.com Micrel, Inc. MIC2205 Absolute Maximum Ratings(1) Operating Ratings(2) Supply Voltage (VIN) ............................................ +6V Output Switch Voltage (VSW) ............................... +6V Output Switch Current (ISW) ................................... 2A Logic Input Voltage (VEN,VLOWQ) .............. -0.3V to VIN Storage Temperature (Ts)................ -60C to +150C ESD Rating(3) ....................................................... 3kV Supply Voltage (VIN)............................+2.7V to +5.5V Logic Input Voltage (VEN,VLOWQ) .............. -0.3V to VIN Junction Temperature (TJ) .............. -40C to +125C Junction Thermal Resistance 3x3 MLF-10L (JA) ................................... 60C/W Electrical Characteristics (4) VIN = VEN = VLOWQ =3.6V; L = 2.2H; COUT = 2.2F; TA = 25C, unless noted. Bold values indicate -40C< TJ < +125C Parameter Condition Min 2.7 Supply Voltage Range Under-Voltage Lockout Threshold Typ (turn-on) 2.45 UVLO Hysteresis 2.55 Max Units 5.5 V 2.65 V 100 mV Quiescent Current, PWM mode VFB = 0.9 * VNOM (not switching) 690 900 A Quiescent Current, LDO mode VLOWQ = 0V;IOUT = 0mA 16 29 A Shutdown Current VEN = 0V 0.01 5 A [Adjustable] Feedback Voltage 1% 2% (over temperature) 0.99 0.98 1 1.01 1.02 V [Fixed Output] Voltages Nominal VOUT tolerance -1 -2 +1 +2 % FB pin input current 1 0.75 1 nA 1.85 Current Limit in PWM Mode VFB = 0.9 * VNOM Output Voltage Line Regulation VOUT > 2V; VIN = VOUT+300mV to 5.5V; ILOAD= 100mA VOUT < 2V; VIN = 2.7V to 5.5V; ILOAD= 100mA 0.13 A Output Voltage Load Regulation, PWM Mode 20mA < ILOAD < 300mA 0.2 0.5 % Output Voltage Load Regulation, LDO Mode 100A < ILOAD < 50mA VLOWQ = 0V 0.1 0.2 % Maximum Duty Cycle VFB 0.4V PWM Switch ONResistance ISW = 50mA VFB = 0.7VFB_NOM (High Side Switch) ISW = -50mA VFB = 1.1VFB_NOM (Low Side Switch) % 100 % 0.4 0.4 Oscillator Frequency 1.8 2 2.2 MHz LOWQ threshold voltage 0.5 0.85 1.3 V 0.1 2 A 0.85 1.3 V 0.1 2 A LOWQ Input Current 0.5 Enable Threshold Enable Input Current LDO Dropout Voltage April 2005 IOUT = 50mA Note 5 110 3 mV M9999-041105 www.micrel.com Micrel, Inc. MIC2205 Parameter Condition Min Output Voltage Noise LOWQ = 0V; COUT = 2.2F, 10Hz to 100kHz LDO Current Limit LOWQ = 0V; VOUT = 0V (LDO Mode) Typ Max Units 75 Vrms 120 mA Over-Temperature Shutdown 160 C Over-Temperature Hysteresis 20 C 60 Notes 1. Exceeding the absolute maximum rating may damage the device. 2. The device is not guaranteed to function outside its operating rating. 3. Devices are ESD sensitive. Handling precautions recommended. Human body model: 1.5k in series with 100pF. 4. Specification for packaged product only. 5. Dropout voltage is defined as the input-to-output differential at which the output voltage drops 2% below its nominal value that is initially measured at a 1V differential. For outputs below 2.7V, the dropout voltage is the input-to-output voltage differential with a minimum input voltage of 2.7V. April 2005 4 M9999-041105 www.micrel.com Micrel, Inc. MIC2205 Typical Characteristics - PWM Mode Bode Plot 85 70 65 60 50 70 65 60 100 200 300 400 OUTPUT CURRENT (mA) 1.0V OUT Efficiency VIN = 4.2V 70 65 60 55 50 0 60 1.95 1.9 1.85 VIN = 3.6V 1.8 -40 -20 0 20 40 60 80 100 120 TEMPERATURE (C) April 2005 VIN = 3.6V 80 VIN = 4.2V 75 70 65 60 50 100 200 300 400 OUTPUT CURRENT (mA) 0 100 200 300 400 OUTPUT CURRENT (mA) Quiescent Current vs. Supply Voltage 900 1.006 1.004 1.002 1.000 0.998 0.996 0.994 VIN = 3.6V LowQ = VIN 0.992 0 800 700 600 500 400 300 200 100 0 2.7 100 200 300 400 OUTPUT CURRENT (mA) Peak Current Limit vs. Supply Voltage CURRENT LIMIT (mA) FREQUENCY (MHz) 2 0 VIN = 3.6V VF B = 0.9V 3.4 4.1 4.8 SUPPLY VOLTAGE (V) 5.5 Enable Threshold vs. Supply Voltage 1.5 1200 2.15 2.05 VIN = 3V 85 55 1.008 Frequency vs. Temperature 2.2 2.1 VIN = 4.2V 65 0.990 100 200 300 400 500 600 OUTPUT CURRENT (mA) 100 200 300 400 500 600 OUTPUT CURRENT (mA) 1.2V OUT Efficiency Load Regulation FEEDBACK VOLTAGE (V) VIN = 3.6V 0 90 VIN = 3.6V 1.010 VIN = 3V 75 50 95 70 50 80 65 60 VIN = 3V 75 50 85 70 100 200 300 400 OUTPUT CURRENT (mA) 80 55 90 75 1.38V OUT Efficiency 85 55 0 0 90 EFFICIENCY (%) 75 VIN = 4.2V 55 95 VIN = 4.2V VIN = 3.6V 80 55 VIN = 3.6V 80 EFFICIENCY (%) 75 -18 -36 1E+6 1M 90 85 EFFICIENCY (%) 36 18 0 VIN = 4.2V 80 VIN = 3V 95 VIN = 3.6V QUIESCENT CURRENT (A) 72 54 VIN = 3V 90 EFFICIENCY (%) 90 85 1.8V OUT Efficiency 100 VIN = 3V 95 1.5V OUT Efficiency 95 EFFICIENCY (%) 108 90 2.5V OUT Efficiency ENABLE THRESHOLD (V) 30 20 VIN = 3.6V 10 VOUT = 1.8V 0 L = 2.2 H Gain COUT = 2.2 F -10 C = 120pF FF -20 1E+2 1E+3 1E+4 1E+5 100 1k 10k 100k FREQUENCY (Hz) 100 EFFICIENCY (%) Phase 60 50 40 144 126 PHASE () GAIN (dB) 80 70 1000 800 600 400 200 LowQ = VIN 0 2.7 3.4 4.1 4.8 SUPPLY VOLTAGE (V) 5 5.5 1.4 1.3 1.2 1.1 1.0 0.9 0.8 0.7 0.6 LowQ = V IN 0.5 2.7 3.4 4.1 4.8 SUPPLY VOLTAGE (V) 5.5 M9999-041105 www.micrel.com Micrel, Inc. MIC2205 Typical Characteristics - PWM Mode (cont.) Turn-On Time vs. Supply Voltage 100 TURN-ON DELAY (s) 90 80 70 60 50 40 30 20 10 V = 3.6V IN 0 2.7 3.4 4.1 4.8 SUPPLY VOLTAGE (V) April 2005 5.5 6 M9999-041105 www.micrel.com Micrel, Inc. MIC2205 Typical Characteristics - LDO Mode PSRR vs. Output Current 80 60 60 40 4.2V 3V 20 IOUT = 50mA VOUT = 1.8V 3.6V COUT = 2.2 F 0 1E-2 1E+1 1 10 1E+2 1k 0.01 1E-1 100 1E+3 0.1 1E+0 FREQUENCY (Hz) 20 VIN = 3.6 VOUT = 1.8V COUT = 2.2 F I OUT = 50mA 0 1E-2 1E+1 1 10 1E+2 1k 0.01 1E-1 100 1E+3 0.1 1E+0 FREQUENCY (Hz) 250 200 150 100 50 VOUT = 3.3V 0 Dropout Voltage vs. Temperature 80 120 140 70 80 60 40 20 LowQ = 0V 0 2.7 3.4 4.1 4.8 SUPPLY VOLTAGE (V) 120 100 80 60 40 VOUT = 3.3V IOUT = 50mA LowQ = 0V 20 0 -40 -20 0 20 40 60 80 100 120 TEMPERATURE (C) 5.5 Dropout Voltage vs. Temperature 50 40 30 20 0 -40 -20 0 20 40 60 80 100 120 TEMPERATURE (C) Dropout Voltage vs. Temperature Output Voltage vs. Temperature 35 8 1.827 25 20 15 5 VOUT = 3.3V IOUT = 10mA LowQ = 0V 0 -40 -20 0 20 40 60 80 100 120 TEMPERATURE (C) 5 4 3 2 1 0 -40 -20 0 20 40 60 80 100 120 TEMPERATURE (C) Enable Threshold Voltage vs. Supply Voltage 1.4 90 TURN-ON DELAY (s) 100 1.1 1.0 0.9 0.8 0.7 0.6 0.5 2.7 April 2005 3.4 4.1 4.8 SUPPLY VOLTAGE (V) 5.5 1.800 1.791 1.782 1.773 LowQ = 0V 1.764 -40 -20 0 20 40 60 80 100 120 TEMPERATURE (C) 60 50 40 30 20 0 2.7 Quiescent Current vs. Temperature 25 80 70 10 LowQ = 0V 1.809 Turn-On Time vs. Supply Voltage 1.5 1.3 1.2 VOUT = 3.3V IOUT = 1mA LowQ = 0V 1.818 VIN = 3.6V LowQ = 0V 3.4 4.1 4.8 5.5 SUPPLY VOLTAGE (V) 7 QUIESCENT CURRENT (A) 10 6 OUTPUT VOLTAGE (V) 1.836 7 VOUT = 3.3V IOUT = 25mA LowQ = 0V 10 9 30 20 40 60 80 100 OUTPUT CURRENT (mA) 60 40 DROPOUT VOLTAGE (mV) DROPOUT VOLTAGE (mV) DROPOUT VOLTAGE (mV) 160 100 0 Dropout Voltage vs. Temperature 140 DROPOUT VOLTAGE (mV) CURRENT LIMIT (mA) IOUT = 100 A 40 Current Limit vs. Supply Voltage ENABLE THRESHOLD (V) IOUT = 0A Dropout vs. Output Current DROPOUT VOLTAGE (mV) 80 PSRR (dB) PSRR (dB) PSRR vs. Input Voltage IOUT = 50mA 20 15 IOUT = 1mA IOUT = 100 A 10 5 VIN = 3.6V LowQ = 0V 0 -40 -20 0 20 40 60 80 100 120 TEMPERATURE (C) M9999-041105 www.micrel.com Micrel, Inc. MIC2205 Typical Characteristics - LDO Mode (cont.) Quiescent Current vs. Temperature Quiescent Current vs. Supply Voltage 20 IOUT = 60mA IOUT = 0A 15 10 5 0 LowQ = 0V 1 2 3 4 5 SUPPLY VOLTAGE (V) 0 25 24 23 22 21 20 19 18 17 16 15 2.7 IOUT = 100 A LowQ = 0V 3.4 4.1 4.8 5.5 SUPPLY VOLTAGE (V) QUIESCENT CURRENT (A) 25 IOUT = 100 A QUIESCENT CURRENT (A) QUIESCENT CURRENT (A) 25 Quiescent Current vs. Output Current 24 23 22 21 20 19 18 17 16 15 0 VIN = 3.6V LowQ = 0V 20 40 60 80 100 OUTPUT CURRENT (mA) Output Voltage vs. Output Current OUTPUT VOLTAGE (V) 1.836 1.827 1.818 1.809 1.8 1.791 1.782 1.773 1.764 0 April 2005 VIN = 3.6V VOUT =1.8V LowQ = 0V 20 40 60 80 100 OUTPUT CURRENT (mA) 8 M9999-041105 www.micrel.com Micrel, Inc. MIC2205 Functional Diagram VIN AVIN P-Channel Current Limit 6 BIAS HSD SW PWM Control VOUT Anti-Shoot Through COUT LSD N-Channel Current Limit R1 EN Enable and Control Logic LOWQ Bias, UVLO, Thermal Shutdown FB Soft Start EA R2 1.0V LDO Block LDO Current Limit EA 1.0V LDO PGND SGND MIC2205 Block Diagram April 2005 9 M9999-041105 www.micrel.com Micrel, Inc. MIC2205 Functional Characteristics Load Transient PWM Mode Output Voltage AC Coupled (50mV/div) Output Current (100mA/div) LowQ = VIN Time 20 s/div Enable Transient PWM Mode VOUT (50mV/div) ENABLE (1V/div) LowQ = 0V Time 40 s/div April 2005 10 M9999-041105 www.micrel.com Micrel, Inc. MIC2205 Functional Characteristics April 2005 11 M9999-041105 www.micrel.com Micrel, Inc. MIC2205 Functional Description for bypassing. VIN VIN provides power to the MOSFETs for the switch mode regulator section, along with the current limiting sensing. Due to the high switching speeds, a 1F capacitor is recommended close to VIN and the power ground (PGND) pin for bypassing. Please refer to layout recommendations. FB The feedback pin (FB) provides the control path to control the output. For adjustable versions, a resistor divider connecting the feedback to the output is used to adjust the desired output voltage. The output voltage is calculated as follows: R1 VOUT = VREF x + 1 R2 AVIN Analog VIN (AVIN) provides power to the LDO section and the bias through an internal 6 Ohm resistor. AVIN and VIN must be tied together. Careful layout should be considered to ensure high frequency switching noise caused by VIN is reduced before reaching AVIN. where VREF is equal to 1.0V. A feedforward capacitor is recommended for most designs using the adjustable output voltage option. To reduce battery current draw, a 100K feedback resistor is recommended from the output to the FB pin (R1). Also, a feedforward capacitor should be connected between the output and feedback (across R1). The large resistor value and the parasitic capacitance of the FB pin can cause a high frequency pole that can reduce the overall system phase margin. By placing a feedforward capacitor, these effects can be significantly reduced. Feedforward capacitance (CFF) can be calculated as follows: LDO The LDO pin is the output of the linear regulator and should be connected to the output. In LOWQ mode (LOWQ<1.5V), the LDO provides the output voltage. In PWM mode (LOWQ>1.5V) the LDO pin is high impedance. EN The enable pin provides a logic level control of the output. In the off state, supply current of the device is greatly reduced (typically <1A). Also, in the off state, the output drive is placed in a "tri-stated" condition, where both the high side P-channel Mosfet and the low-side N-channel are in an "off" or non-conducting state. Do not drive the enable pin above the supply voltage. CFF = For fixed options A feed forward capacitor from the output to the FB pin is required. Typically a 100pF small ceramic capacitor is recommended SW The switch (SW) pin connects directly to the inductor and provides the switching current nessasary to operate in PWM mode. Due to the high speed switching on this pin, the switch node should be routed away from sensitive nodes. LOWQ The LOWQ pin provides a logic level control between the internal PWM mode and the low noise linear regulator mode. With LOWQ pulled low (<0.5V), quiescent current of the device is greatly reduced by switching to a low noise linear regulator mode that has a typical IQ of 18A. In linear (LDO) mode the output can deliver 60mA of current to the output. By placing LOWQ high (>1.5V), this transitions the device into a constant frequency PWM buck regulator mode. This allows the device the ability to efficiently deliver up to 600mA of output current at the same output voltage. PGND Power ground (PGND) is the ground path for the high current PWM mode. The current loop for the power ground should be as small as possible and separate from the Analog ground (AGND) loop. Refer to the layout considerations for more details. SGND Signal ground (SGND) is the ground path for the biasing and control circuitry. The current loop for the signal ground should be separate from the Power ground (PGND) loop. Refer to the layout considerations for more details. BIAS The BIAS pin supplies the power to the internal power to the control and reference circuitry. The bias is powered from AVIN through an internal 6 resistor. A small 0.1F capacitor is recommended April 2005 1 2 x R1x 160kHz 12 M9999-041105 www.micrel.com Micrel, Inc. MIC2205 Applications Information Output Capacitor The MIC2205 is a 600mA PWM power supply that utilizes a LOWQTM light load mode to maximize battery efficiency in light load conditions. This is achieved with a LOWQ control pin that when pulled low, shuts down all the biasing and drive current for the PWM regulator, drawing only 18A of operating current. This allows the output to be regulated through the LDO output, capable of providing 60mA of output current. This method has the advantage of producing a clean, low current, ultra low noise output in LOWQTM mode. During LOWQTM mode, the SW node becomes high impedance, blocking current flow. Other methods of reducing quiescent current, such as pulse frequency modulation (PFM) or bursting techniques, create large amplitude, low frequency ripple voltages that can be detrimental to system operation. When more than 60mA is required, the LOWQ pin can be forced high, causing the MIC2205 to enter PWM mode. In this case, the LDO output makes a "hand-off" to the PWM regulator with virtually no variation in output voltage. The LDO output then turns off allowing up to 600mA of current to be efficiently supplied through the PWM output to the load. Even though the MIC2205 is optimized for a 2.2F output capacitor, output capacitance can be varied from 1F to 4.7F. The MIC2205 utilizes type III internal compensation and utilizes an internal high frequency zero to compensate for the double pole roll off of the LC filter. For this reason, larger output capacitors can create instabilities. X5R or X7R dielectrics are recommended for the output capacitor. Y5V dielectrics lose most of their capacitance over temperature and are therefore, not recommended. In addition to a 2.2F, a small 10nF is recommended close to the load for high frequency filtering. Smaller case size capacitors are recommended due to there lower ESR and ESL. Inductor Selection The MIC2205 is designed for use with a 2.2H inductor. Proper selection should ensure the inductor can handle the maximum average and peak currents required by the load. Maximum current ratings of the inductor are generally given in two methods; permissible DC current and saturation current. Permissible DC current can be rated either for a 40C temperature rise or a 10% to 20% loss in inductance. Ensure that the inductor selected can handle the maximum operating current. When saturation current is specified, make sure that there is enough margin that the peak current will not saturate the inductor. Peak inductor current can be calculated as follows: Input Capacitor A minimum 1F ceramic is recommended on the VIN pin for bypassing. X5R or X7R dielectrics are recommended for the input capacitor. Y5V dielectrics lose most of their capacitance over temperature and are therefore, not recommended. A minimum 1F is recommended close to the VIN and PGND pins for high frequency filtering. Smaller case size capacitors are recommended due to their lower ESR and ESL. Please refer to layout recommendations for proper layout of the input capacitor. April 2005 IPK = IOUT 13 V VOUT 1 - OUT VIN + 2x f xL M9999-041105 www.micrel.com Micrel, Inc. MIC2205 Layout Recommendations VOUT L1 CBIAS GND VIN LowQ MIC2205 EN CFF R1 R2 Top L1 VOUT CBIAS GND VIN LowQ MIC2205 EN CFF R1 R2 Bottom Note: The above figures demonstrate the recommended layout for the MIC2205 adjustable option. April 2005 14 M9999-041105 www.micrel.com Micrel, Inc. MIC2205 MIC2205 V IN 2.7V to 5.5V C1 1F LowQ 8 VIN SW 9 4 AVIN LDO 2 6 EN FB 5 7 LOWQ 3 BIAS C2 0.1F 2.2H VOUT R1 100k C3 100pF C4 2.2F R2 125k PGND AGND 10 GND 1 GND Adjustable Output MIC2205 V IN 2.7V to 5.5V C1 1F LowQ C2 0.1F 8 VIN SW 9 4 AVIN LDO 2 6 EN FB 5 7 LOWQ 3 BIAS 2.2H VOUT C3 100pF C4 2.2F PGND AGND GND 10 1 GND Fixed Output Item Part Number Description Manufacturer C1 06036D105MAT2 GRM185R60J105KE21D 1F Ceramic Capacitor X5R, 6.3V 0603 1F Ceramic Capacitor X5R, 6.3V 0603 AVX (4) Murata 1 C4 06036D225MAT2 GRM188R61A225KE34 2.2F Ceramic Capacitor X5R, 10V 0603 2.2uF Ceramic Capacitor X5R, 10V 0603 AVX (4) Murata 1 C3 VJ0402A101KXAA 100pF Ceramic Capacitor Vishay 1 C2 0201ZD103MAT2 GRM033R10J103KA01D 10nF Ceramic Capacitor 6.3V 0201 10nF Ceramic Capacitor 6.3V 0201 AVX (4) Murata 1 L1 LQH32CN2R2M53K CDRH2D14-2R2 2.2H Inductor 97m 3.2mmx2.5mmx1.55mm 2.2H Inductor 94m 3.2mmx3.2mmx1.55mm Murata (2) Sumida CRCW04021002F 100k 1% 0402 Vishay Dale Vishay Dale (3) Vishay Dale (3) Vishay Dale (3) Vishay Dale (3) Vishay Dale (1) R1 (1) (3) Qty (4) 1 (3) 1 (3) R2 CRCW04026652F CRCW04021243F CRCW04022003F CRCW04024023F 66.5 k 1% 0402 For 2.5VOUT 124 k 1% 0402 For 1.8 VOUT 200 k 1% 0402 For 1.5 VOUT 402 k 1% 0402 For 1.2 VOUT Open For 1.0 VOUT U1 MIC2205BML 2MHz Synchronous Buck Regulator with LOWQ Mode TM Micrel, Inc. (5) 1 Notes: 1. For adjustable version only. 2. Sumida Tel: 408-982-9660 3. Murata Tel: 949-916-4000 4. Vishay Tel: 402-644-4218 5. Micrel, Inc. Tel: 408-944-0800 April 2005 15 M9999-041105 www.micrel.com Micrel, Inc. MIC2205 Package Information 10-Lead MLFTM (ML) MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http:/www.micrel.com The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser's use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser's own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. (c) 2004 Micrel, Incorporated. April 2005 16 M9999-041105 www.micrel.com