NJG1512HD3
- 1 -
SPDT SWITCH GaAs MMIC
■
■■
■GENERAL DESCRIPTION ■
■■
■PACKAGE OUTLINE
NJG1512HD3 is a GaAs SPDT switch IC featuring
high isolation and low insertion loss.
This switch allows low operating voltage f rom 2. 5V at
the wide freq uency range from 1MHz to 3GHz.
The ultra small & ultra thin USB6-D3 package is
applied.
■
■■
■FEATURES
●
●●
●Single, low voltage contr o l +2.5~+5.5V
●
●●
●High isolation 44dB typ. @f=0.1~2G Hz
●
●●
●Low insertion loss 0.6dB typ. @f=1.0GHz
1.0dB typ. @f=2. 0G hz
●
●●
●Low current consumption 2uA typ
●
●●
●
Ultra small & ultra t h in package
USB6-D3 (Package size: 2.0x1.8x0. 8mm)
■
■■
■PIN CONFI GURATIO N
■
■■
■TRUTH TABLE
V
CTR1
H L
V
CTR2
L H
PC-P1 OFF ON
PC-P2 ON OFF
“H”=V
CTR (H),
“L”=V
CTR (L)
HD3 Type
(TOP VIEW)
1
2
3 4
5
6
Pin Connection
1.VCTL2
2.PC
3.VCTL1
4.P1
5.GND
6.P2
NJG1512HD3
- 2 -
■
■■
■ABSOLUTE MAXIMUM RATING S (T
a
=25°C, Z
s
=Z
l
=50Ω)
PARAMETER SYMBOL CONDITIONS RATINGS UNITS
Input Power P
in
V
CTL
=0V/2.7V
27 dBm
Control Volt age V
CTR
6.0 V
Power Dissipation P
D
200
mW
Operating Temp. T
opr
-20~+85 °C
Storag e Temp. T
stg
-40~+150 °C
■
■■
■ELECTRICAL CHARACTERISTICS
(TEST CIRCUIT : V
CTL
=0/2.7V, Z
s
=Z
o
=50Ω, T
a
=25°C)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
Control voltage (L)
V
CTL (L)
-0.2 0 0.2 V
Control voltage (H)
V
CTL (H)
2.5 2.7 5.5 V
Control curr ent
I
CTL
- 2.0 4.0 uA
Insertion loss 1 LOSS1 f= 1. 0G Hz, P
in
=0dBm
- 0.6 1.0
dB
Insertion loss 2 LOSS2 f= 2. 0G Hz, P
in
=0dBm
- 1.0 1.2
dB
Isolation 1 ISL1 f= 1. 0GHz, P
in
=0dBm
41 44 -
dB
Isolation 2 ISL2 f= 2. 0GHz, P
in
=0dBm
41 44 -
dB
Pin at 1dB
compression point P
-1dB
f=2.0GHz 19.0 22.0 - dBm
VSWR VSWR f= 0. 1~2.5GHz, ON STATE - 1.2 1.8
Switching time T
SW
f=0.1~2.5GHz - 8 - ns
NJG1512HD3
- 3 -
■
■■
■TERMINAL INFORMATION
No. SYMBOL EXPLANATION
1 VCTL2
Control port 2. The voltage of this port controls PC to P1 state. The ‘ON’ and
‘OFF’ state is toggled by controlling voltage of this terminal such as high-state
(2.5~5.5V) or low-state (-0.2~+0.2V). The voltage of 3rd pin has to be set to
opposite state. The bypass capacitor has to be chosen to reduce switching
speed delay from 10pF~1000pF range.
2 PC Common RF port. In order to block the DC bias voltage of internal circuit, an
external capacitor is required. (1~500MHz: 1uF, 0.5~2.5GHz: 56pF)
3 VCTL1
Control port 1. The voltage of this port controls PC to P1 state. The ‘ON’ and
‘OFF’ state is toggled by controlling voltage of this terminal such as high-state
(2.5~5.5V) or low-state (-0.2~+0.2V). The voltage of 1st pin has to be set to
opposite state. The bypass capacitor has to be chosen to reduce switching
speed delay from 10pF~1000pF range.
4 P1
RF port. This port is connected with PC port by controlling 1st pin (V
CTL (H)
) to
2.5~5.5V and 3rd pin (V
CTL (L)
) to -0.2~+0.2V. An external capacitor is required
to block the DC bias voltage of internal circuit. (1~500MHz: 1uF, 0.5~2.5GHz:
56pF)
5 GND Ground terminal. Please connect this terminal with ground plane as close as
possible for excellent RF performance.
6 P2
RF port. This port is connected with PC port by controlling 3rd pin (V
CTL (H)
) to
2.5~5.5V and 1st pin (V
CTL (L)
) to -0.2~+0.2V. An external capacitor is required
to block the DC bias voltage of internal circuit. (1~500MHz: 1uF, 0.5~2.5GHz:
56pF)
NJG1512HD3
- 4 -
-3.0
-2.5
-2.0
-1.5
-1.0
-0.5
0.0
0.0 0.5 1.0 1.5 2.0 2.5 3.0
Insertion Loss (dB)
Frequency (GHz)
PC-P2 Inse tion Loss v s. Frequency
( VCTL1=2.7V, VCTL2=0V, Pin=0dBm )
■
■■
■TYPICAL CHARACTERISTICS
-3.0
-2.5
-2.0
-1.5
-1.0
-0.5
0.0
0.0 0.5 1.0 1.5 2.0 2.5 3.0
Insertion Loss (dB)
Frequency (GHz)
PC-P1 Inse tion Loss v s. Frequency
( VCTL1=0V, VCTL2=2.7V, Pin=0dBm )
-60
-50
-40
-30
-20
-10
0
0.0 0.5 1.0 1.5 2.0 2.5 3.0
Isolation (dB)
Frequency (GHz)
PC- P 2 I s olation v s. Fre q uency
( VCTL1=0V, VCTL2=2.7V, Pin=0dBm )
-60
-50
-40
-30
-20
-10
0
0.0 0.5 1.0 1.5 2.0 2.5 3.0
Isolation (dB)
Frequency (GHz)
PC- P 1 I s olation v s. Fre q uency
( VCTL1=2.7V, VCTL2=0V, Pin=0dBm )
1.0
1.5
2.0
2.5
3.0
0.0 0.5 1.0 1.5 2.0 2.5 3.0
VSWR
Frequency (GHz)
P1 VSWR vs. Frequency
( VCTL1=0V, VCTL2=2.7V, Pin=0dBm )
1.0
1.5
2.0
2.5
3.0
0.0 0.5 1.0 1.5 2.0 2.5 3.0
VSWR
Frequency (GHz)
P2 VSWR vs. Frequency
( VCTL1=2.7V, VCTL2=0V, Pi n=0dBm )
NJG1512HD3
- 5 -
■
■■
■TYPICAL CHARACTERISTICS
-50
-45
-40
-35
-30
0 5 10 15 20 25 30
PC-P1
PC-P2
Isolation (dB)
Input Power (dBm)
Isolation vs. Input Power
( VCTL=0V/2.7V, f=2GHz )
-3.0
-2.5
-2.0
-1.5
-1.0
-0.5
0.0
0 5 10 15 20 25 30
PC-P1
PC-P2
Insertion Loss (dB)
Input Power (dBm)
Insertion Loss vs. Input Power
( VCTL=0V/2.7V, f=2GHz )
-1.5
-1.0
-0.5
0.0
-50 0 50 100
Insertion Loss (dB)
Ambient Te mperature (
o
C )
PC-P1 Loss vs. Ambient Temperature
( f=2GHz, Pin=0dBm, VCTL1=0V, VCTL2=2.7V )
-1.5
-1.0
-0.5
0.0
-50 0 50 100
Insertion Loss (dB)
Ambient Te mperature ( oC )
PC-P2 Loss vs. Ambient Temperature
( f=2GHz, Pin=0dBm, VCTL1=2.7V, VCTL2=0V )
-50
-45
-40
-35
-30
-50 0 50 100
Isolation (d B)
Ambient Temp erature (
o
C )
PC-P1 Isolation vs. Ambient Temperature
( f=2GHz, Pin=0dBm, VCTL1=2.7V, VCTL2=0V )
-50
-45
-40
-35
-30
-50 0 50 100
Isolation (dB)
Ambient Temp erature (
o
C )
PC-P2 Isolation vs. Ambient Temperature
( f=2GHz, Pin=0dBm, VCTL1=0V, VCTL2=2.7V )
NJG1512HD3
- 6 -
■
■■
■TYPICAL CHARACTERISTICS
1.0
1.2
1.4
1.6
1.8
2.0
-50 0 50 100
VSWR
Ambient Te mperature ( oC )
P2 VSWR vs. Ambient Temperature
( f=2GHz, Pin=0dBm, VCTL1=2.7V, VCTL2=0V )
1.0
1.2
1.4
1.6
1.8
2.0
-50 0 50 100
VSWR
Ambient Te mperature ( oC )
P1 VSWR vs. Ambient Temperature
( f=2GHz, Pin=0dBm, VCTL1=0V, VCTL2=2.7V )
0
1
2
3
4
5
-50 0 50 100
Control Current ICTL (uA)
Ambient Temp erature ( oC )
PC-P2 ICTL vs. Ambient Temperature
( f=2GHz, VCTL1= 2.7V, VCTL2=0V )
0
1
2
3
4
5
-50 0 50 100
Control Current ICTL (uA)
Ambient Temp erature ( oC )
PC-P1 ICTL vs. Ambient Temperature
( f=2GHz, VCTL1=0V, VCTL2=2.7V )
NJG1512HD3
- 7 -
-50
-45
-40
-35
-30
-50 0 50 100
Isolation (dB)
Ambient Te mperature ( oC )
PC-P2 Isolation vs. Ambient Temperature
( f=1GHz, Pin=0dBm, VCTL1=0V, VCTL2=2.7V )
■
■■
■TYPICAL CHARACTERISTICS
-50
-45
-40
-35
-30
-50 0 50 100
Isolation (dB)
Ambient Temp erature ( oC )
PC-P1 Isolation vs. Ambient Temperature
( f=1GHz, Pin=0dBm, VCTL1=2.7V, VCTL2=0V )
-1.5
-1.0
-0.5
0.0
-50 0 50 100
Insertion Loss (dB)
Ambient Te mperature ( oC )
PC-P2 Loss vs. Ambient Temperature
( f=1GHz, Pin=0dBm, VCTL1=2.7V, VCTL2=0V )
-1.5
-1.0
-0.5
0.0
-50 0 50 100
Insertion Loss (dB)
Ambient Te mperature ( oC )
PC-P1 Loss vs. Ambient Temperature
( f=1GHz, Pin=0dBm, VCTL1=0V, VCTL2=2.7V )
1.0
1.2
1.4
1.6
1.8
2.0
-50 0 50 100
VSWR
Ambient Te mperature ( oC )
P1 VSWR vs. Ambient Temperature
( f=1GHz, Pin=0dBm, VCTL1=0V, VCTL2=2.7V )
1.0
1.2
1.4
1.6
1.8
2.0
-50 0 50 100
VSWR
Ambient Te mperature ( oC )
P2 VSWR vs. Ambient Temperature
( f=1GHz, Pin=0dBm, VCTL1=2.7V, VCTL2=0V )
NJG1512HD3
- 8 -
■
■■
■APPLI CATION CIRCUIT: Sing le control signal operat ion by using C- MOS inverter
(frequency range: 0.1~2.0GHz)
■
■■
■RECOMM ENDED PCB DESIGN
PRECAUTIONS
[1] The external capacitors should be connected to the input and output RF terminals
(P
1
, P
2
, P
C
) to block DC current. Please use a 0.1uF capacitor at 1 to 500MHz, a
56pF at 500MHz to 2.0GHz.
[2] To avoid coupling between terminals, the capacitors have to be placed at the
control ter minals (V
CTR1
, V
CTR2
) as close as possible. The capacitor values of 1000pF
at 1 to 500MHz, 10pF at 500MHz to 2GHz are desired. In g eneral, t he switching tim e
is depending on the capacitor values, so please be careful choosing capacitor
values.
[3] For good isolation characteristics, the ground terminals (5pin) should be directly
connected to the ground patterns and through-holes as close as possible using
relatively wide patterns.
Test circuit 1
0.5~2GHz Test circuit 2
1~500MHz
C1~C3 56pF 0.1uF
C4, C5 10pF 1000pF
(TOP VIEW)
PCB SIZE=
19.4x14.0mm
PCB: FR-4, t=0.5mm
STRIPLINE WIDTH =1mm
CAPACITO R: size 1005
1
2
3 4
5
6
V
CTL2
(2.7V/0V)
C1
C2
C3
C4
C5
V
CTL1
(0V/2.7V)
PC
P2
P1
NJG1512HD3
- 9 -
■
■■
■ PACKAGE OUTLINE (USB10-D3)
K
P K G
R
M
1.8
2
0.038
0.5
0.5
0.8
1 0.3
0.2
0.3
45°
0.018
R0.075
A A
A-A cross section
0.8
TERMINAL TREAT :Au
PCB :FR5
Molding material : Epoxy resin
UNIT :mm
WEIGHT :13mg
Cautions on using this product
This product contains Gallium-A rs enide (GaA s) which is a harmful material.
• Do NOT eat or put into mouth.
• Do NOT dispos e i n fire or break up this product.
• Do NOT chemically make gas or powder with this produc t.
• To waste this
p
roduct
,
p
lease obe
y
the relatin
g
law of
y
ou
r
countr
y
.
This product m ay be dam aged with elec tric stat ic disc harge (ESD) or spike vol tage. Pleas e handle
with care to avoid t hese damages.
[CAUTION]
The specifications on this databook are only
given for information , without any guarantee
as regards either mistakes or omissions. The
application circuits in this databook are
described only to show representative usages
of the product and not intended for the
guarantee or permission of any right including
the industrial rights.
Please connect with G ND terminal.
