SPECIFICATION
MODEL LCM-40DA
DC VOLTAGE RANGE
RATED POWER
OUTPUT
SETUP, RISE TIME Note.5
HOLD UP TIME (Typ.)
VOLTAGE RANGE Note.4
FREQUENCY RANGE
POWER FACTOR (Typ.)
EFFICIENCY (Typ.) Note.6
AC CURRENT (Typ.)
INPUT
INRUSH CURRENT (Typ.)
LEAKAGE CURRENT
SAFETY STANDARDS
DALI STANDARDS
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSIONOTHERS
NOTE
PACKING
2 ~ 100V 2 ~ 67V2 ~ 80V 2 ~ 57V 2 ~ 45V 2 ~ 40V
42W
700mVp-p
110V 65V
500ms, 80ms / 230VAC at rated power
180 ~ 295VAC 254 ~ 417VDC
47 ~ 63Hz
91%
Compliance to EN55015, EN61000-3-2 Class C( 40% ) ; EN61000-3-3;≧rated power GB17625.1,GB17743
Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61547 light industry level (surge 2KV), criteria A
-30 ~ +60 (Refer to "Derating Curve")℃
20 ~ 90% RH non-condensing
-40 ~ +80 , 10 ~ 95% RH℃
10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
193.6K hrs min. MIL-HDBK-217F (25 )℃
123.5*81.5*23mm (L*W*H)
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.℃
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf parallel capacitor.
3. Please see "DIP switch table".
4. Derating may be needed under low input voltage. Please check the static characteristics for more details.
5. Length of set up time is measured at first cold start. Turning ON/OFF the power supply may lead to increase of the set up time.
6. Efficiency is measured at 500mA/80V output set by DIP switch.
7. No load power consumption<0.5W(LCM-40DA) and <1.2W(LCM-40DA-AUX) is measured at 180 277VAC, with lighting fixture connected and output
~
current dimmed to 0%.
8. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the
complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
0.24Kg ; 54pcs/15Kg/1.12CUFT
40W Multiple-Stage Output Current LED Power Supply LCM-40DA series
RIPPLE & NOISE (max.) Note.2
NO LOAD OUTPUT VOLTAGE (max.)
ENVIRONMENT
SAFETY &
FUNCTION
EMC
PROTECTION
16ms/230VAC at rated power
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
I/P-O/P:3.75KVAC
UL8750, ENEC EN61347-1, EN61347-2-13, EN62384 independent, GB19510.14,GB19510.1 approved
Comply with IEC62386-101, 102, 207
I/P-O/P:>100M Ohms / 500VDC / 25 / 70% RH℃
SELECTABLE CURRENT
Note.3
350mA 600mA500mA 700mA 900mA 1050mA
CURRENT ACCURACY
EMC IMMUNITY
EMC EMISSION
SHORT CIRCUIT
OVER VOLTAGE
OVER TEMPERATURE
AUXILIARY POWER (optional)
TEMP. COMPENSATION
SYNCHRONIZATION
Constant current limiting, recovers automatically after fault condition is removed
Shut down o/p voltage, re-power on to recover
Please see "Synchronization Operation"
DIMMING Please see "Dimming Operation"
Protection type : Shutdown o/p voltage, re-power on to recover
110 ~ 130V
12V @ 50mA for driving fan; Tolerance 5%±
By external NTC(not provide with the power supply), please see "Temperature compensation operation"
TOTAL HARMONIC DISTORTION
Total harmonic distortion will be lower than 20% when output loading is 75% or higher
<0.5mA / 240VAC
0.23A/230VAC 0.2A/277VAC
RIPPLE CURRENT
Output current level selectable by DIP S.W.
180~295VAC input only
Built-in active PFC function
Protections: Short circuit / Over voltage / Over temperature
Cooling by free air convection
Fully isolated plastic case
ⅡClass power unit, no FG
Built-in DALI interface and push dimming function
Optional 12V/50mA auxiliary output (Model No.: LCM-40DA-AUX)
IP20 design
Logarithm or linear dimming curve selectable(Meet IEC62386-207)
Temperature compensation function by external NTC
No load power consumption <0.5W(<1.2W for LCM-40DA-AUX)(Note.7)
Power supplies synchronization function up to 10 units
Suitable for indoor LED lighting applications
3 years warranty
■Features :
±5%
PF 0.975/230VAC, PF 0.96/277VAC at (Please refer to "Power Factor Characteristic" curve)≧≧
rated power
COLD START 20A(t =260 s measured at 50% I ) at 230VACwidth peakμ
SELV
FMM
110
±5%
±0.03%/ (0 ~ 50 )℃℃
MAX. No. of PSUs on 16A
CIRCUIT BREAKER 26 units (circuit breaker of type B) / 44 units (circuit breaker of type C) at 230VAC
Mechanical Specification Case No.LCM-60A Unit:mm
Block Diagram
DIM+
DIM-
DETECTION
CIRCUIT
EMI FILTER
RECTIFIERS
POWER
SWITCHING
FILTER
&
RECTIFIERS
RECTIFIERS
+V
+12Vaux
-V
I/P
CONTROL
O.V.P.
&
MCU
PFC
CIRCUIT
PFC
CONTROL O.T.P.
PWM
PFC fosc : 60KHz
PWM fosc : 80KHz
TB3
TB5
2
3
4
5
1
1
2
TB1
SYN. Connector(CN101/CN100):JST B2B-XH or equivalent
Pin No. Assignment Mating Housing
JST XHP
or equivalent
Terminal
JST SXH-001T-P0.6
or equivalent
1,3
2,4
+
-
Terminal Pin No. Assignment(TB5)
Terminal Pin No. Assignment(TB1)
Pin No.
Pin No. Pin No.
1
14
2
25
3
Assignment
Assignment Assignment
+Vo
AC/L DA+
-Vo
AC/N DA-
PUSH
Terminal Pin No. Assignment(TB3)
Pin No. Pin No.
1
2
3
4
Assignment Assignment
+FAN(optional) +NTC
-NTC-FAN(optional)
Others
20
40
60
80
100
(HORIZONTAL)
-15 0 15 30
04050-30 60 70
1
3
2
4
CN100
CN101
CURRENT
LIMIT
1050mA
※T case: Max. Case Temperature.
Bottom View
O.L.P.
(optional)
LOAD (%)
INPUT VOLTAGE (V) 60Hz
180 190 200 210 220 230 240 260 270 280 295
100
90
80
70
60
50
40
LOAD (%)
Derating Curve
LOAD (%)
Derating Curve Static Characteristics
AMBIENT TEMPERATURE ( )℃
LOAD (%)
250
LOAD (%)
File Name:LCM-40DA-SPEC 2015-05-28
40W Multiple-Stage Output Current LED Power Supply LCM-40DA series
2- 4.2
6.75
6.75
68
81.5
6.75 110
123.5
6.75
39.3 65.5
2-M3
7.8 7.8
SYN.
1
2
3
4
ON
654321
4
23
Tcase
40
15
EFFICIENCY (%)
EFFICIENCY (%)
LCM-40DA series possess superior working efficiency that up to 91% can be reached in field applications.
EFFICIENCY vs LOAD
LCM-40DA is a multiple-stage output current supply, selection of output current through DIP switch as table below.
DIP Switch Table
Constant Current Mode Constant Current Mode
Io
350mA
500mA
600mA
700mA(Factory Setting)
900mA
1050mA
DIP S.W. 1
---- ----
----
----
----
----
----
----
----
----
----
----
----
----
----
----
----
----
2
ON
ON
ON
ON
ON
ON
ON
ON
ON
3
ON
ON
ON
4
ON
ON
5
ON
6
ON
ON
ON
File Name:LCM-40DA-SPEC 2015-05-28
40W Multiple-Stage Output Current LED Power Supply LCM-40DA series
LOAD
(230Vac Input)
LOAD
(277Vac Input)
Power Factor Characteristic
45.0%
50.0%
55.0%
60.0%
65.0%
70.0%
75.0%
80.0%
85.0%
90.0%
95.0%
10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
350
500
600
700
900
1050
45.0%
50.0%
55.0%
60.0%
65.0%
70.0%
75.0%
80.0%
85.0%
90.0%
95.0%
10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
350
500
600
700
900
1050
0.50
0.53
0.56
0.59
0.62
0.65
0.68
0.71
0.74
0.77
0.80
0.83
0.86
0.89
0.92
0.95
0.98
10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
350
500
600
700
900
1050
0.70
0.73
0.76
0.79
0.82
0.85
0.88
0.91
0.94
0.97
1.00
10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
350
500
600
700
900
1050
PF
PF
LOAD
(230Vac Input)
LOAD
(277Vac Input)
(40W) (40W)
10 drivers(max.) synchronization (1 master + 9 slaves)
Maximum cable length between each units : 20 meter.
LCM-40DA
(Slave 2)
LCM-40DA
------
+
+
+
+
+
+
SYN.
DA-
Push Button
AC/N
AC/L
DA+
PUSH
AC/N
AC/L
SYN. SYN.
LCM-40DA
(Master)
LCM-40DA
(Slave 1)
DIMMING OPERATION
SYNCHRONIZATION OPERATION
※PUSH dim(primary side)
Maximum number of drivers up to 10 pcs.
Maximum length of the cable, from push button to last driver is 20 meter.
Factory setting at 100%.
Warning: The pushbutton can only be connected in between the PUSH terminal of LCM-40DA andAC/L (brown or black color). It would cause short
circuit if it is connected to AC/N.
DALI protocol including 16 groups and 64 addresses.
First step is fixed at 6% of output.
※DALI interface(primary side)
Ignore <0.05 sec.To avoid reaction on AC spike
Short push 0.1~1 sec.Push to turn ON-OFF
Long push 1.5~10 sec.Dimming up or down
Reset push >11 sec.Setting light to 100%
20m 20m
NOTE Please make sure all units are set to 100% dimming setting(factory default) before synchronizing.:
File Name:LCM-40DA-SPEC 2015-05-28
40W Multiple-Stage Output Current LED Power Supply LCM-40DA series
Every long pushing action will change the dimming direction.
65
70
75
80
85
90
95
100
105
55 60 65 70 75 80 85 90 95
220KO
330KO
470KO
NTC derating curve
220KΩ
330KΩ
470KΩ
Sensed Temperature(degree)
Output Io (%)
TEMPERATURE COMPENSATION OPERATION
LCM-40DA have the built-in temperature compensation function (T ,Io ). By connecting a temperature sensor (NTC resistor) between the NTC +/-↑↓
terminal of LCM-40DAand the detecting point on the lighting system or the surrounding environment, output current of LCM-40DA could be
correspondingly changed to ensure the long life of LED.
2.
NTC resistance
220K
330K
470K
Output Current
< 60 , 100% of the rated current (corresponds to the setting current level)℃
< 70 , 100% of the rated current (corresponds to the setting current level)℃
< 80 , 100% of the rated current (corresponds to the setting current level)℃
> 60 , output current begin to reduce, details please refer to the curve.℃
> 70 , output current begin to reduce, details please refer to the curve.℃
> 80 , output current begin to reduce, details please refer to the curve.℃
3. Synchronization function of the power supply will be invalid when the "temperature compensation" function is in use.
Notes: 1. MW does not offer the NTC resistor and all the data above are measured by using THINKING TTC03 series.
2. If other brands of NTC resistor is applied,please check the temperature curve first.
File Name:LCM-40DA-SPEC 2015-05-28
40W Multiple-Stage Output Current LED Power Supply LCM-40DA series
1.LCM-40DA can still be operated well when the NTC resistor is not connected and the value of output current will be the current level that you set
through the DIP switch.
