Chip Inductors0805HS Series (2012) Ceramic body and wirewound construction provide highest SRFs available in 0805 size. These ultra- compact inductors provide exceptional Q values, even at high frequencies. Part Inductance Percent , 3 SRF Min* Roc Max Ipc Max Number nH Tolerance Q Min MHz Ohms mA 0805HS-030TMBC 3.3 @ 250 MHz 20,10,5 50 @ 1500 MHz 6000 .08 600 0805HS-060TMBC 6.8 @ 250 MHz 20,10,5 50 @ 1000 MHz 5500 14 600 0805HS-080TMBC 8.2 @ 250 MHz 20,10,5 50 @ 1000 MHz 4700 12 600 O805HS-120TMBC 12 @ 250 MHz 20,10,5 50 @ 500 MHz 4000 15 600 0805HS-150TMBC 15 @ 250 MHz 20,10,5 50 @ 500 MHz 3400 17 600 0805HS-180TMBC 18 @ 250 MHz 20,10,5 50 @ 500 MHz 3300 .20 600 0805HS-220TMBC 22 @ 250 MHz 20,10,5 55 @ 500 MHz 2600 22 500 0805HS-270TMBC 27 @ 250 MHz 20,10,5 55 @ 500 MHz 2500 25 500 0805HS-330TMBC 33 @ 250 MHz 20,10,5,2 60 @ 500 MHz 2050 OF 500 0805HS-390T MBC 39 @ 250 MHz 20,10,5,2 60 @ 500 MHz 2000 .29 500 0805HS-470TMBC 47 @ 200 MHz 20,10,5,2 60 @ 500 MHz 1650 ot 500 0805HS-560TKBC 56 @ 200 MHz 10,5,2,1 60 @ 500 MHz 1550 34 500 0805HS-680TKBC 68 @ 200 MHz 10,5,2,1 60 @ 500 MHz 1450 38 500 0805HS-820TKBC 82 @ 150 MHz 10,5,2,1 65 @ 500 MHz 1300 42 400 O0805HS-101TKBC 100 @ 150 MHz 10,5,2,1 65 @ 500 MHz 1200 46 400 0805HS-121TKBC 120 @ 150 MHz 10,5,2,1 50 @ 250 MHz 1100 51 400 0805HS-151TKBC 150 @ 100 MHz 10,5,2,1 50 @ 250 MHz 920 56 400 O805HS-181TKBC 180 @ 100 MHz 10,5,2,1 50 @ 250 MHz 870 64 400 0805HS-221TKBC 220 @ 100 MHz 10,5,2 50 @ 250 MHz 850 A) 400 1. Inductance measured using Coilcratt SMD-A fixture in HP4191A impedance 4. SRF measured using HP8753B network analyzer and Coilcraft SMD-D analyzer with Coilcraft-provided correlation pieces. For recommended test test fixture. procedures, contact Coilcraft. 5. Rec measured on Cambridge Technology micro-ohmmeter and Coilcraft 2. Bold number indicates standard tolerance. When ordering other tolerances, CCF858 test fixture. replace the third to the last letter in the part number with the proper tolerance 6. For 15'C rise. code: F=1%, Ga2%, J=5%, K=10%, M=20%. (e.g. O805HS-O30TJBC for a 5% tolerance part} 3. Q measured using HP4291A with HP16193 test fixture and on HPB753B with Coiicraft SMD-E test fixture. Document 159-1 Revised 10/24/95 1102 Silver Lake Road Cary, Illinois60013 Phone 847/639-6400 Fax 847/639-1469 E-mail info@coilcraft.com Databy Fax 800/651-6974 Web http://www.coilcraft.comO805HS Series (2012) TYPICAL Q vs FREQUENCY eat 100 aN LMM .| LLL. : Yj Yi / 7 Y SNA SY SS N NEN A NS SN ; AY iv VA a | Ae ZO eT 10 = Frequency MHz Lvs FREQUENCY 8 _ H>| 1,000 overall + be c+ + F ( +S RE Pad A i i Layout 100 F | e (ft terminal - L apron O10 58 both ends (n H ) A;/B C E F/G/H'1j| 4 | 10 Max. Max. Max. 085 060 (057 | .050 020.040 .070| .040 ; 030, [2,16 ' 1,52] 1,45 1,27 0.51 1,02 1,78 1,02 0,76 | Parts/Reel: 7 2,000; 13 7,500 Tape width: 8mm 10 100 1.000 Frequency MHz Coilcrakt Document 159-2 Revised 2/:/96 1102 Silver Lake Road Cary, Illinois60013_ Phone 847/639-6400 Fax 847/639-1469 E-mail info@coilcraft.com Databy Fax 800/651-6974 Web hitp://www.coilcraft.com