USB224x Ultra Fast USB 2.0 MultiFormat, SD/MMC, and MS Flash Media Controllers PRODUCT FEATURES Datasheet General Description The SMSC USB224x is a USB 2.0 compliant, Hi-Speed bulk only1 mass storage class peripheral controller intended for reading and writing to popular flash media from the xDPicture CardTM (xD)2, Memory Stick(R) (MS), Secure Digital (SD), and MultiMediaCardTM (MMC) families. The SMSC USB224x is a fully integrated, single chip solution capable of ultra high performance operation. Average sustained transfer rates exceeding 35 MB/s are possible if the media and host can support those rates. The USB2244/44i includes provisions to read/write secure media formats. General Features -- Targeted for applications in which single or "combo" media sockets are used Hardware-controlled data flow architecture for all selfmapped media Pipelined hardware support for access to non-selfmapped media Order number with "i" denote the products that support the industrial temperature range of -40C to 85C Support included for secure media format on a licensed, customized basis -- xD player mode operation -- Socket switch polarities, etc. 8051 8-bit microprocessor -- 60 MHz - single cycle execution -- 64 KB ROM | 14 KB RAM Supports a single external 3.3 V supply source; internal regulators provide 1.8 V internal core voltage for additional bill of materials and power savings Optimized pinout improves signal routing which eases implementation for improved signal integrity Flash Media Specification Compliance Secure Digital 2.0 -- HS-SD, SDHC -- TransFlashTM and reduced form factor media MultiMediaCard 4.2 Memory Stick Formats -- 1/4/8-bit MMC -- MS 1.43, Pro 1.02, Duo 1.10 -- Pro-HG Duo 1.01 - MS, MS Duo, HS-MS, MS Pro-HG, MS Pro Single chip flash media controller with SDIO and MMC Streaming Mode support Extended configuration options On board 24 MHz crystal driver circuit Optional external 24 MHz clock input3 Internal card power FET -- 200 mA -- "Fold-back" short circuit protection -- USB2240/40i/41/4i: multiplexed interface for use with "combo" card sockets -- USB2242/42i: MS flash media reader/writer -- USB2244/44i: SD/MMC flash media reader/writer Hardware Features xD-Picture Card 1.2 Software Features -- USB2244/44i: SD Secure -- USB2242/42i: Sony MagicGateTM -- Up to 8 GPIOs for special function use -- One GPIO with up to 200 mA drive Low pin count 36-pin QFN (6x6 mm) lead-free RoHS compliant package USB2240/40i/41/41i GPIO configuration and polarity Customizable vendor specific data Optimized for low latency interrupt handling Reduced memory footprint Applications Flash media card reader/writers Desktop and mobile PCs Printers Consumer A/V and media players/viewers Compatible with - Microsoft(R) VistaTM and Vista ReadyBoostTM - Windows(R) XP, ME, 2K SP4 - Apple Mac OSx(R) - Linux Mass Storage Class Drivers Media Activity LED 1.Bulk only is not applicable to USB2240/40i/41/41i. 2.xD-Picture Card is not applicable to USB2241/41i. 3.Only applicable to USB2240/40i/41/41i. SMSC USB224x Revision 2.0 (10-14-09) DATASHEET Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet ORDER NUMBERS: LEAD-FREE ROHS COMPLIANT PACKAGE TYPE / SIZE SD/MMC xD MS/ MS PRO/ MS PRO-HG USB2240-AEZG-XX 3 3 3 0C to 70C USB2240i-AEZG-XX 3 3 3 -40C to 85C USB2241-AEZG-XX 3 3 0C to 70C 3 3 -40C to 85C 3 0C to 70C 3 -40C to 85C ORDER NUMBERS USB2241i-AEZG-XX 36 QFN USB2242-AEZG-XX 6 x 6 x 0.5 mm USB2242i-AEZG-XX OPERATING TEMPERATURE USB2244-AEZG-XX 3 0C to 70C USB2244i-AEZG-XX 3 -40C to 85C "XX" in the order number indicates the internal ROM firmware revision level. Please contact your SMSC sales representative for more information. This product meets the halogen maximum concentration values per IEC61249-2-21 For RoHS compliance and environmental information, please visit www.smsc.com/rohs 80 ARKAY DRIVE, HAUPPAUGE, NY 11788 (631) 435-6000, FAX (631) 273-3123 Copyright (c) 2009 SMSC or its subsidiaries. All rights reserved. Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical applications. Consequently, complete information sufficient for construction purposes is not necessarily given. Although the information has been checked and is believed to be accurate, no responsibility is assumed for inaccuracies. SMSC reserves the right to make changes to specifications and product descriptions at any time without notice. Contact your local SMSC sales office to obtain the latest specifications before placing your product order. The provision of this information does not convey to the purchaser of the described semiconductor devices any licenses under any patent rights or other intellectual property rights of SMSC or others. All sales are expressly conditional on your agreement to the terms and conditions of the most recently dated version of SMSC's standard Terms of Sale Agreement dated before the date of your order (the "Terms of Sale Agreement"). The product may contain design defects or errors known as anomalies which may cause the product's functions to deviate from published specifications. Anomaly sheets are available upon request. SMSC products are not designed, intended, authorized or warranted for use in any life support or other application where product failure could cause or contribute to personal injury or severe property damage. Any and all such uses without prior written approval of an Officer of SMSC and further testing and/or modification will be fully at the risk of the customer. Copies of this document or other SMSC literature, as well as the Terms of Sale Agreement, may be obtained by visiting SMSC's website at http://www.smsc.com. SMSC is a registered trademark of Standard Microsystems Corporation ("SMSC"). Product names and company names are the trademarks of their respective holders. SMSC makes the following part-numbered device available for purchase only by customers who are xD-Picture Card licensees: USB2240/USB2240i. By purchasing or ordering any of such devices, Buyer represents, warrants, and agrees that Buyer is a duly licensed Licensee under an xD-Picture CardTM License Agreement with Fuji Photo Film Co., Ltd., Olympus Optical Co., Ltd., and Toshiba Corporation; and that Buyer will maintain in effect such xD-Picture Card license and will give SMSC reasonable advance notice of any termination or expiration of such xD-Picture Card license, but in no event less than five days advance notice. SMSC may discontinue making such devices available for purchase by Buyer and/or discontinue further deliveries of such devices if such xD-Picture Card license shall expire, terminate, or cease to be in force, or if Buyer is or becomes in default of such xD-Picture Card license. SMSC DISCLAIMS AND EXCLUDES ANY AND ALL WARRANTIES, INCLUDING WITHOUT LIMITATION ANY AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND AGAINST INFRINGEMENT AND THE LIKE, AND ANY AND ALL WARRANTIES ARISING FROM ANY COURSE OF DEALING OR USAGE OF TRADE. IN NO EVENT SHALL SMSC BE LIABLE FOR ANY DIRECT, INCIDENTAL, INDIRECT, SPECIAL, PUNITIVE, OR CONSEQUENTIAL DAMAGES; OR FOR LOST DATA, PROFITS, SAVINGS OR REVENUES OF ANY KIND; REGARDLESS OF THE FORM OF ACTION, WHETHER BASED ON CONTRACT; TORT; NEGLIGENCE OF SMSC OR OTHERS; STRICT LIABILITY; BREACH OF WARRANTY; OR OTHERWISE; WHETHER OR NOT ANY REMEDY OF BUYER IS HELD TO HAVE FAILED OF ITS ESSENTIAL PURPOSE, AND WHETHER OR NOT SMSC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Revision 2.0 (10-14-09) 2 DATASHEET SMSC USB224x Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet Table of Contents Chapter 1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Chapter 2 Acronyms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Chapter 3 Block Diagrams. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Chapter 4 Pin Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Chapter 5 Pin Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Chapter 6 Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 6.1 USB224x 36-Pin QFN Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 6.2 Buffer Type Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Chapter 7 Pin Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 7.1 Card Reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.2 System Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.2.1 EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.2.2 EEPROM Data Descriptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.2.3 EEPROM Data Descriptor Register Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.2.4 A0h-A7h: Device Power Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.2.5 Device ID Strings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.3 Default Configuration Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.3.1 External Hardware RESET_N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.3.2 USB Bus Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 25 25 25 27 32 33 35 35 36 Chapter 8 Pin Reset States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 8.1 USB2240/40i/41/41i Pin Reset States. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 8.2 USB2242/42i Pin Reset States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 8.3 USB2244/44i Pin Reset States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Chapter 9 DC Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 9.1 Maximum Guaranteed Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.2 Operating Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.3 DC Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.4 Capacitance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.5 Package Thermal Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 42 42 44 45 Chapter 10 AC Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 10.1 Oscillator/Crystal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 10.2 Ceramic Resonator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 10.3 External Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Chapter 11 GPIO Usage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Chapter 12 Package Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 SMSC USB224x 3 DATASHEET Revision 2.0 (10-14-09) Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet Table of Contents Table 5.1 USB2240/2240i 36-Pin QFN Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 5.2 USB2241/2241i 36-Pin QFN Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 5.3 USB2242/2242i 36-Pin QFN Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 5.4 USB2244/2244i 36-Pin QFN Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 6.1 USB224x 36-PiN QFN Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 6.2 Buffer Type Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 7.1 Internal Flash Media Controller Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 7.2 RESET_N Timing for EEPROM Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 8.1 Legend for Pin Reset States Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 8.2 USB2240/40i/41/41i 36-Pin Reset States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 8.3 USB2242/42i 36-Pin Reset States. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 8.4 USB2244/USB2244i 36-Pin Reset States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 9.1 Pin Capacitance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 9.2 36-Pin QFN Package Thermal Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 10.1 Crystal Circuit Legend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 11.1 USB2240/40i and USB2241/41i GPIO Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 11.2 USB2242/42i GPIO Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 11.3 USB2244/44i GPIO Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 12.1 Package Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Revision 2.0 (10-14-09) 4 DATASHEET 15 16 17 18 19 24 25 36 37 37 38 40 44 45 46 48 48 48 50 SMSC USB224x Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet List of Figures Figure 3.1 Figure 3.2 Figure 3.3 Figure 4.1 Figure 4.2 Figure 4.3 Figure 4.4 Figure 7.1 Figure 8.1 Figure 9.1 Figure 10.1 Figure 10.2 Figure 10.3 Figure 12.1 Figure 12.2 USB2240/40i/41/41i Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 USB2242/42i Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 USB2244/44i Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 USB2240/USB2240i 36-Pin QFN Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 USB2241/USB2241i 36-Pin QFN Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 USB2242/USB2242i 36-Pin QFN Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 USB2244/USB2244i 36-Pin QFN Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 RESET_N Timing for EEPROM Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Pin Reset States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Supply Rise Time Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Typical Crystal Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Capacitance Formulas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Ceramic Resonator Usage with SMSC IC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 USB224x 36-QFN, 6x6 mm Body, 0.5 mm Pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Additional Package Information and Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 SMSC USB224x 5 DATASHEET Revision 2.0 (10-14-09) Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet Chapter 1 Overview The SMSC USB224x is a flash media card reader solution fully compliant with the USB 2.0 specification. All required resistors on the USB ports are integrated into the device. This includes all series termination resistors on D+ and D- pins and all required pull-down and pull-up resistors. The over-current sense inputs for the downstream facing ports have internal pull-up resistors. Hardware Features Single chip flash media controller in low pin count 36-pin QFN, lead-free RoHS compliant package Commercial temperature products support 0C to +70C: USB2240/41, USB2242 and USB2244 Industrial temperature products support -40C to +85C: USB2240i/41i, USB2242i and USB2244i Up to 8 GPIOs - Configuration and polarity for special function use such as LED indicators, button inputs, and power control to memory devices - The number of actual GPIOs depends on the implementation configuration used One GPIO available with up to 200 mA drive and "fold-back" short circuit protection 8051 8-bit microprocessor - 60 MHz - single cycle execution - 64 KB ROM |14 KB RAM Supports a single external 3.3 V supply source; internal regulators provide 1.8 V internal core voltage for additional bill of materials and power savings Compliance with the following flash media card specifications: Secure Digital 2.0 - HS-SD and SDHC - TransFlashTM and reduced form factor media MultiMediaCard 4.2 - 1/4/8 bit MMC Memory Stick 1.43 Memory Stick Pro Format 1.02 Memory Stick Pro-HG Duo Format 1.01 - Memory Stick, MS Duo, HS-MS, MS Pro-HG, MS Pro Memory Stick Duo 1.10 xD-Picture Card 1.2 Software Features If the OEM is using an external EEPROM, the following features are available: - Customizable vendor, product, language, and device ID's - 12-hex digits maximum for the serial number string - 28-character manufacturer ID and product strings for the flash media reader/writer - LED blink interval or duration Revision 2.0 (10-14-09) 6 DATASHEET SMSC USB224x Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet Chapter 2 Acronyms ATA: Advanced Technology Attachment FET: Field Effect Transistor LUN: Logical Unit Number MMC: MultiMediaCard1 MSC: Memory Stick Controller2 PLL: Phase-Locked Loop QFN: Quad Flat No leads RoHS: Restriction of Hazardous Substances Directive RXD: Received eXchange Data SDIO: Secure Digital Input/Output SDC: Secure Digital Controller SIE: Serial Interface Engine TXD: Transmit eXchange Data UART: Universal Asynchronous Receiver-Transmitter UCHAR: Unsigned Character UINT: Unsigned Integer *Note: In order to develop, make, use, or sell readers and/or other products using or incorporating any of the SMSC devices made the subject of this document or to use related SMSC software programs, technical information and licenses under patent and other intellectual property rights from or through various persons or entities, including without limitation media standard companies, forums, and associations, and other patent holders may be required. These media standard companies, forums, and associations include without limitation the following: Sony Corporation (Memory Stick, Memory Stick Pro); SD3 LLC (Secure Digital); MultiMedia Card Association (MultiMediaCard); the SSFDC Forum (SmartMedia); the Compact Flash Association (Compact Flash); and Fuji Photo Film Co., Ltd., Olympus Optical Co., Ltd., and Toshiba Corporation (xD-Picture Card). SMSC does not make such licenses or technical information available; does not promise or represent that any such licenses or technical information will actually be obtainable from or through the various persons or entities (including the media standard companies, forums, and associations), or with respect to the terms under which they may be made available; and is not responsible for the accuracy or sufficiency of, or otherwise with respect to, any such technical information. SMSC's obligations (if any) under the Terms of Sale Agreement, or any other agreement with any customer, or otherwise, with respect to infringement, including without limitation any obligations to defend or settle claims, to reimburse for costs, or to pay damages, shall not apply to any of the devices made the subject of this document or any software programs related to any of such devices, or to any combinations involving any of them, with respect to infringement or claimed infringement of any existing or future patents related to solid state disk or other flash memory technology or applications ("Solid State Disk Patents"). By making any purchase of any of the devices made the subject of this document, the customer represents, warrants, and agrees that it has obtained all necessary licenses under then-existing Solid State Disk Patents for the manufacture, use and sale of solid state disk and other flash memory products and that the customer will timely obtain at no cost or expense to SMSC all necessary licenses under Solid State Disk Patents; that the manufacture and testing by or for SMSC of the units of any of the devices made the subject of this document which may be sold to the customer, and any sale by SMSC of such units to the customer, are valid exercises of the customer's rights and licenses under such Solid State Disk Patents; that SMSC shall have no obligation for royalties or otherwise under any Solid State Disk Patents by reason of any such manufacture, use, or sale of such units; and that SMSC shall have no obligation for any costs or expenses related to the customer's obtaining or having obtained rights or licenses under any Solid State Disk Patents. SMSC MAKES NO WARRANTIES, EXPRESS, IMPLIED, OR STATUTORY, IN REGARD TO INFRINGEMENT OR OTHER VIOLATION OF INTELLECTUAL PROPERTY RIGHTS. SMSC DISCLAIMS AND EXCLUDES ANY AND ALL WARRANTIES AGAINST INFRINGEMENT AND THE LIKE. No license is granted by SMSC expressly, by implication, by estoppel or otherwise, under any patent, trademark, copyright, mask work right, trade secret, or other intellectual property right. **To obtain this software program the appropriate SMSC Software License Agreement must be executed and in effect. Forms of these Software License Agreements may be obtained by contacting SMSC. 1.MMC, SDIO, and SDC are not applicable to USB2242/42i. 2.Not applicable to USB2244/44i. SMSC USB224x 7 DATASHEET Revision 2.0 (10-14-09) Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet Chapter 3 Block Diagrams USB2240 / 40i USB2241 / 41i* USB Host SIE CTL PHY AUTO_CBW PROC BUS INTFC BUS FMDU INTFC CTL SD/ MMC FMI Multiplexed Interface MS xD* 3.3 V EP0 TX EP0 RX 1.8 V Reg BUS INTFC VDD18 24 MHz Crystal 4K total EP1 RX EP1 TX EP2 RX EP2 TX PLL XDATA BRIDGE + BUS ARBITER VDD18PLL 3.3 V RAM 1.8 V Reg PWR_FET1 GPIOs RAM 10 KB ROM 64 KB ADDR MAP GPIO10 / CRD_PWR 8 pins Program Memory I/O Bus Clock Generation and Control SFR RAM 8051 PROCESSOR NOTE: xD-Picture Card is not applicable to USB2241/41i. Figure 3.1 USB2240/40i/41/41i Block Diagram Revision 2.0 (10-14-09) 8 DATASHEET SMSC USB224x Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet USB2242 / USB2242i USB Host SIE CTL PHY AUTO_CBW PROC BUS INTFC BUS FMDU INTFC CTL FMI Media Interface MS 3.3 V EP0 TX EP0 RX 1.8 V Reg BUS INTFC VDD18 RAM 4K total EP1 RX EP1 TX EP2 RX EP2 TX 24 MHz Crystal PLL XDATA BRIDGE + BUS ARBITER VDD18PLL 3.3 V 1.8 V Reg PWR_FET1 GPIOs RAM 10 KB ROM 64 KB ADDR MAP GPIO10 / CRD_PWR 7 pins Program Memory I/O Bus Clock Generation and Control SFR RAM 8051 PROCESSOR Figure 3.2 USB2242/42i Block Diagram SMSC USB224x 9 DATASHEET Revision 2.0 (10-14-09) Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet USB2244 / USB2244i USB Host SIE CTL PHY AUTO_CBW PROC BUS INTFC BUS FMDU INTFC CTL FMI SD/ MMC Media Interface 3.3 V EP0 TX EP0 RX 1.8 V Reg BUS INTFC VDD18 RAM 4K total EP1 RX EP1 TX EP2 RX EP2 TX 24 MHz Crystal PLL XDATA BRIDGE + BUS ARBITER VDD18PLL 3.3 V 1.8 V Reg PWR_FET1 GPIOs RAM 10 KB ROM 64 KB ADDR MAP GPIO10 / CRD_PWR 7 pins Program Memory I/O Bus Clock Generation and Control SFR RAM 8051 PROCESSOR Figure 3.3 USB2244/44i Block Diagram Revision 2.0 (10-14-09) 10 DATASHEET SMSC USB224x Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet GPIO2 / RXD / SDA GPIO15 (SD_nCD) xD_D5 / SD_D2 GPIO12 (MS_INS) xD_D6 / SD_D3 / MS_D3 VDD33 GPIO10 (CRD_PWR) xD_D7 / SD_D4 / MS_D2 GPIO14 (xD_nCD) 27 26 25 24 23 22 21 20 19 Chapter 4 Pin Configurations TEST 28 18 GPIO4 29 17 xD_nB/R xD_D4 / GPIO6 (SD_WP) / MS_SCLK 30 16 xD_nRE GPIO7 / TXD / SCK / MS_SKT_SEL 31 XTAL2 32 XTAL1 (CLKIN) 33 VDD18PLL 34 RBIAS 35 VDDA33 36 SMSC USB2240/2240i (Top View QFN-36) 1 2 3 4 5 6 7 8 9 GPIO1 (LED) USB+ USB- xD_D3 / SD_D1 / MS_D5 xD_D2 / SD_D0 / MS_D4 VDD33 xD_D1 / SD_D7 / MS_D6 xD_D0 / SD_D6 / MS_D7 xD_nWP / SD_CLK / MS_BS Ground Pad (must be connected to VSS) RESET_N 15 xD_nCE 14 VDD33 13 VDD18 12 xD_nWE 11 xD_CLE / SD_CMD / MS_D0 10 xD_ALE / SD_D5 / MS_D1 Indicates pins on the bottom of the device. Figure 4.1 USB2240/USB2240i 36-Pin QFN Diagram SMSC USB224x 11 DATASHEET Revision 2.0 (10-14-09) Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers GPIO14 VDD33 22 19 SD_D3 / MS_D3 23 GPIO10 (CRD_PWR) GPIO12 (MS_INS) 24 SD_D4 / MS_D2 SD_D2 25 20 GPIO15 (SD_nCD) 26 21 GPIO2 / RXD / SDA 27 Datasheet TEST 28 18 GPIO4 29 17 NC GPIO6 (SD_WP) / MS_SCLK 30 16 NC GPIO7 / TXD / SCK / MS_SKT_SEL 31 15 NC XTAL2 32 XTAL1 (CLKIN) 33 VDD18PLL 34 RBIAS 35 VDDA33 36 SMSC USB2241/2241i (Top View QFN-36) 4 5 6 7 8 9 VDD33 SD_D7 / MS_D6 SD_D6 / MS_D7 SD_CLK / MS_BS 3 USB- SD_D0 / MS_D4 2 USB+ SD_D1 / MS_D5 1 GPIO1 (LED) Ground Pad (must be connected to VSS) RESET_N 14 VDD33 13 VDD18 12 NC 11 SD_CMD / MS_D0 10 SD_D5 / MS_D1 Indicates pins on the bottom of the device. Figure 4.2 USB2241/USB2241i 36-Pin QFN Diagram Revision 2.0 (10-14-09) 12 DATASHEET SMSC USB224x Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers GPIO14 VDD33 22 19 MS_D3 23 GPIO10 (CRD_PWR) GPIO12 (MS_INS) 24 MS_D2 NC 25 20 GPIO15 26 21 GPIO2 / RXD / SDA 27 Datasheet TEST 28 18 RESET_N GPIO4 29 17 NC MS _SCLK 30 16 NC GPIO7 / TXD / SCK / MS_SKT_SEL 31 15 NC XTAL2 32 14 VDD33 XTAL1 (CLKIN) 33 13 VDD18 VDD18PLL 34 RBIAS 35 VDDA33 36 SMSC USB2242/2242i (Top View QFN-36) 1 2 3 4 5 6 7 8 9 GPIO1 (LED) USB+ USB- MS_D5 MS_D4 VDD33 MS_D6 MS_D7 MS_BS Ground Pad (must be connected to VSS) 12 NC 11 MS_D0 10 MS_D1 Indicates pins on the bottom of the device. Figure 4.3 USB2242/USB2242i 36-Pin QFN Diagram SMSC USB224x 13 DATASHEET Revision 2.0 (10-14-09) Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers GPIO14 VDD33 22 19 SD_D3 23 GPIO10 (CRD_PWR) GPIO12 24 SD_D4 SD_D2 25 20 GPIO15 (SD_nCD) 26 21 GPIO2 / RXD / SDA 27 Datasheet TEST 28 18 RESET_N GPIO4 29 17 NC SD _WP 30 16 NC 15 NC 5 6 7 8 9 VDD33 SD_D7 SD_D6 SD_CLK 36 SD_D0 VDDA33 Ground Pad (must be connected to VSS) 4 35 3 34 RBIAS USB- VDD18PLL SD_D1 33 2 XTAL1 (CLKIN) SMSC USB2244/2244i (Top View QFN-36) USB+ 32 1 31 XTAL2 GPIO1 (LED) GPIO7 / TXD / SCK 14 VDD33 13 VDD18 12 NC 11 SD_CMD 10 SD_D5 Indicates pins on the bottom of the device. Figure 4.4 USB2244/USB2244i 36-Pin QFN Diagram Revision 2.0 (10-14-09) 14 DATASHEET SMSC USB224x Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet Chapter 5 Pin Tables Table 5.1 USB2240/2240i 36-Pin QFN Package xD/SD/MS INTERFACE (18 PINS) xD_D3 / SD_D1 / MS_D5 xD_D2 / SD_D0 / MS_D4 xD_D1 / SD_D7 / MS_D6 xD_D0 / SD_D6 / MS_D7 xD_nWP / SD_CLK / MS_BS xD_ALE / SD_D5 / MS_D1 xD_CLE / SD_CMD / MS_D0 xD_D7 / SD_D4 / MS_D2 xD_D6 / SD_D3 / MS_D3 xD_D5 / SD_D2 xD_nRE xD_nWE xD_D4 / GPIO6 (SD_WP) / MS_SCLK xD_nB/R xD_nCE GPIO12 (MS_INS) GPIO14 (xD_nCD) GPIO15 (SD_nCD) USB INTERFACE (5 PINS) USB+ USB- XTAL1 (CLKIN) XTAL2 RBIAS MISC (7 Pins) GPIO1 (LED) GPIO2 / RXD / SDA GPIO4 GPIO10 (CRD_PWR) TEST RESET_N GPIO7 / TXD / SCK / MS_SKT_SEL DIGITAL, POWER (6 PINS) (3) VDD33 VDDA33 VDD18 VDD18PLL TOTAL 36 SMSC USB224x 15 DATASHEET Revision 2.0 (10-14-09) Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet Table 5.2 USB2241/2241i 36-Pin QFN Package SD/MS INTERFACE (14 PINS) SD_D1 / MS_D5 SD_D0 / MS_D4 SD_D7 / MS_D6 SD_D6 / MS_D7 SD_CLK / MS_BS SD_D5 / MS_D1 SD_CMD / MS_D0 SD_D4 / MS_D2 SD_D3 / MS_D3 SD_D2 GPIO6 (SD_WP) / MS_SCLK GPIO12 (MS_INS) GPIO14 GPIO15 (SD_nCD) USB INTERFACE (5 PINS) USB+ USB- XTAL1 (CLKIN) XTAL2 RBIAS MISC (11 Pins) GPIO1 (LED) GPIO2 / RXD / SDA GPIO4 GPIO7 / TXD / SCK / MS_SKT_SEL GPIO10 (CRD_PWR) TEST RESET_N (4) NC DIGITAL, POWER (6 PINS) (3) VDD33 VDDA33 VDD18 VDD18PLL TOTAL 36 Revision 2.0 (10-14-09) 16 DATASHEET SMSC USB224x Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet Table 5.3 USB2242/2242i 36-Pin QFN Package MS INTERFACE (11 PINS) MS_D0 MS_D1 MS_D2 MS_D3 MS_D4 MS_D5 MS_D6 MS_D7 MS_BS MS_SCLK GPIO12 (MS_INS) USB INTERFACE (5 PINS) USB+ USB- XTAL1 (CLKIN) XTAL2 RBIAS MISC (14 PINS) GPIO1 (LED) GPIO2 / RXD / SDA GPIO4 GPIO7 / TXD / SCK / MS_SKT_SEL GPIO10 (CRD_PWR) GPIO14 GPIO15 (5) NC TEST RESET_N DIGITAL, POWER (6 PINS) (3) VDD33 VDDA33 VDD18 VDD18PLL TOTAL 36 SMSC USB224x 17 DATASHEET Revision 2.0 (10-14-09) Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet Table 5.4 USB2244/2244i 36-Pin QFN Package SD/MMC INTERFACE (12 Pins) SD_D0 SD_D1 SD_D2 SD_D3 SD_D4 SD_D5 SD_D6 SD_D7 SD_CLK SD_CMD SD_WP GPIO15 (SD_nCD) USB INTERFACE (5 PINS) USB+ USB- XTAL1 (CLKIN) XTAL2 RBIAS MISC (13 PINS) GPIO1 (LED) GPIO2 / RXD / SDA GPIO4 GPIO7 / TXD / SCK GPIO10 (CRD_PWR) GPIO12 GPIO14 (4) NC TEST RESET_N DIGITAL, POWER (6 PINS) (3)VDD33 VDDA33 VDD18 VDD18PLL TOTAL 36 Revision 2.0 (10-14-09) 18 DATASHEET SMSC USB224x Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet Chapter 6 Pin Descriptions This section provides a detailed description of each signal. The signals are arranged in functional groups according to their associated interface. The pin descriptions are applied when using the internal default firmware and can be referenced in Chapter 7, "Pin Configurations," on page 25. Please reference Chapter 2, "Acronyms," on page 7 for a list of the acronyms used. The "n" symbol in the signal name indicates that the active, or asserted, state occurs when the signal is at a low voltage level. When "n" is not present in the signal name, the signal is asserted at the high voltage level. The terms assertion and negation are used exclusively. This is done to avoid confusion when working with a mixture of "active low" and "active high" signals. The term assert, or assertion, indicates that a signal is active, independent of whether that level is represented by a high or low voltage. The term negate, or negation, indicates that a signal is inactive. 6.1 USB224x 36-Pin QFN Pin Descriptions USB2244/44i USB2242/42i USB2241/41i SYMBOL USB2240/40i Table 6.1 USB224x 36-PiN QFN Pin Descriptions BUFFER TYPE DESCRIPTION xD-PICTURE CARD (xD) INTERFACE (APPLIES ONLY TO USB2240/USB2240i) xD_D[7:0] xD_nWP 20 23 25 30 4 5 7 8 I/O12PD 9 O12PD xD Data These bi-directional data signals have weak internal pull-down resistors. xD Write Protect This pin is an active low write protect signal for the xD device and has a weak pull-down resistor that is permanently enabled. xD_ALE 10 O12PD xD Address Strobe This pin is an active high Address Latch Enable signal for the xD device and has a weak pull-down resistor that is permanently enabled. xD_CLE 11 O12PD xD Command Strobe This pin is an active high Command Latch Enable signal for the xD device and has a weak pull-down resistor that is permanently enabled. SMSC USB224x 19 DATASHEET Revision 2.0 (10-14-09) Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet xD_nRE 16 USB2244/44i USB2242/42i USB2241/41i SYMBOL USB2240/40i Table 6.1 USB224x 36-PiN QFN Pin Descriptions (continued) BUFFER TYPE O12PU DESCRIPTION xD Read Enable This pin is an active low read strobe signal for the xD device. When using the internal FET, this pin has a weak internal pull-up resistor that is tied to the output of the internal power FET. If an external FET is used (Internal FET is disabled), then the internal pull-up is not available (external pullups must be used). xD_nWE 12 O12PU xD Write Enable This pin is an active low write strobe signal for the xD device. When using the internal FET, this pin has a weak internal pull-up resistor that is tied to the output of the internal power FET. If an external FET is used (Internal FET is disabled), then the internal pull-up is not available (external pullups must be used). xD_nB/R 17 IPU xD Busy or Data Ready This pin is connected to the BSY/RDY pin of the xD device. When using the internal FET, this pin has a weak internal pull-up resistor that is tied to the output of the internal power FET. If an external FET is used (Internal FET is disabled), then the internal pull-up is not available (external pullups must be used). GPIO14 (xD_nCD) 19 I/O12 xD Card Detection GPIO This is a GPIO designated by the default firmware as the xD-Picture card detection pin. xD_nCE 15 O12PU xD Chip Enable This pin is the active low chip enable signal to the xD device. When using the internal FET, this pin has a weak internal pull-up resistor that is tied to the output of the internal power FET. If an external FET is used (Internal FET is disabled), then the internal pull-up is not available (external pullups must be used). Revision 2.0 (10-14-09) 20 DATASHEET SMSC USB224x Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet USB2244/44i USB2242/42i USB2241/41i SYMBOL USB2240/40i Table 6.1 USB224x 36-PiN QFN Pin Descriptions (continued) BUFFER TYPE DESCRIPTION MEMORY STICK (MS) INTERFACE MS_D[7:0] 8 7 4 5 23 20 10 11 I/O12PD MS System Data In/Out These pins are the bi-directional data signals for the MS device. MS_D0, MS_D2, and MS_D3 have weak pull-down resistors. In serial mode, the most significant bit (MSB) of each byte is transmitted first by either MSC or MS device on MS_D0. In parallel mode, MS_D1 has a pull-down resistor, otherwise it is disabled. In 4- or 8-bit parallel mode, there is a weak pull-down resistor on all MS_D7 - 0 signals. MS_BS 9 O12 MS Bus State This pin is connected to the bus state (BS) pin of the MS device. It is used to control the bus states 0, 1, 2 and 3 (BS0, BS1, BS2 and BS3) of the MS device. 30 MS_SCLK O12 MS System CLK This pin is an output clock signal to the MS device. The clock frequency is software configurable. GPIO12 (MS_INS) 24 IPU MS Card Insertion GPIO This is a GPIO designated by the default firmware as the Memory Stick card detection pin. SECURE DIGITAL (SD) / MULTIMEDIACARD (MMC) INTERFACE SD_D[7:0] SD_CLK 7 8 10 20 23 25 4 5 7 8 10 20 23 25 4 5 I/O12PU 9 9 O12 SD Data The pins are bi-directional data signals SD_D0 SD_D7 and have weak pull-up resistors. SD Clock This is an output clock signal to SD/MMC device. The clock frequency is software configurable. SD_CMD 11 11 I/O12PU SD Command This is a bi-directional signal that connects to the CMD signal of the SD/MMC device and has a weak internal pull-up resistor. SMSC USB224x 21 DATASHEET Revision 2.0 (10-14-09) Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet GPIO6 (SD_WP) 30 GPIO15 (SD_nCD) 26 USB2244/44i USB2242/42i USB2241/41i SYMBOL USB2240/40i Table 6.1 USB224x 36-PiN QFN Pin Descriptions (continued) BUFFER TYPE I/O12 DESCRIPTION SD Write Protect Detection GPIO This is a GPIO designated by the default firmware as the Secure Digital card mechanical write protect detection pin. I/O12 SD Card Detect GPIO This is a GPIO designated by the default firmware as the Secure Digital card detection pin. USB INTERFACE USB+ USB- 2 3 I/O-U RBIAS 35 I-R USB Bus Data These pins connect to the USB bus data signals. USB Transceiver Bias A 12.0 k, 1.0% resistor is attached from VSS to this pin in order to set the transceiver's internal bias currents. XTAL1 (CLKIN) 33 ICLKx 24 MHz Crystal (External clock input) This pin can be connected to one terminal of the crystal or can be connected to an external 24 MHz clock when a crystal is not used. XTAL2 32 OCLKx 24 MHz Crystal This is the other terminal of the crystal, or it is left open when an external clock source is used to drive XTAL1(CLKIN). It may not be used to drive any external circuitry other than the crystal circuit. VDDA33 36 3.3 V Analog Power VDD18PLL 34 1.8 V PLL Power +1.8 V Filtered analog power for internal PLL. This pin must have a 1.0 F(or greater) 20% (ESR <0.1 ) capacitor to VSS. MISC GPIO1 (LED) 1 I/O12 General Purpose I/O (GPIO): This pin may be used either as input, edge sensitive interrupt input, or output. Custom firmware is required to activate this function. LED: GPIO1 can be used as an LED output. Revision 2.0 (10-14-09) 22 DATASHEET SMSC USB224x Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet GPIO2 / USB2244/44i USB2242/42i USB2241/41i SYMBOL USB2240/40i Table 6.1 USB224x 36-PiN QFN Pin Descriptions (continued) DESCRIPTION I/O12 GPIO: This pin may be used either as input, edge sensitive interrupt input, or output. Custom firmware is required to activate this function. RXD / I RXD: This signal can be used as input to the RXD of UART in the device. Custom firmware is required to activate this function. SDA I/O12 SDA: This is the data pin when used with an external serial EEPROM. I/O12 GPIO: This pin may be used either as input, edge sensitive interrupt input, or output. Custom firmware is required to activate this function. GPIO4 27 BUFFER TYPE 29 For the USB2240/USB2240i only, this pin can be used as the xD-Picture card detection pin. GPIO7 / 31 TXD / SCK / MS_SKT_SEL I/O12 GPIO: This pin may be used either as input, edge sensitive interrupt input, or output. Custom firmware is required to activate this function. O12 TXD: The GPIO7 can be used as an output TXD of UART in the device. Custom firmware is required to activate this function. O12 SCK: This is the clock output when used with an external EEPROM. I MS_SKT_SEL: On the positive edge of RESET_N, this pin is sampled to determined the Memory Stick socket size. 1 = 8-bit 0 = 4-bit GPIO10 21 I/O200 GPIO: This pin may be used either as input, edge sensitive interrupt input, or output. Custom firmware is required to activate this function. (CRD_PWR) CRD_PWR: Card power drive of 3.3 V at either 100 mA or 200 mA. RESET_N 18 IS RESET Input: This active low signal is used by the system to reset the chip. The active low pulse should be at least 1 s wide. TEST 28 I TEST Input: Tie this pin to ground for normal operation. I/O12 This pin may be used either as input, edge sensitive interrupt input, or output. I/O12 This pin may be used either as input, edge sensitive interrupt input, or output. I/O12 This pin may be used either as input, edge sensitive interrupt input, or output. GPIO12 24 GPIO14 GPIO15 SMSC USB224x 19 26 23 DATASHEET Revision 2.0 (10-14-09) Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet USB2242/42i USB2244/44i NC USB2241/41i SYMBOL USB2240/40i Table 6.1 USB224x 36-PiN QFN Pin Descriptions (continued) 12 15 16 17 12 15 16 17 25 12 15 16 17 BUFFER TYPE DESCRIPTION No Connect. No trace or signal should be routed/attached to these pins. DIGITAL / POWER VDD18 13 +1.8 V core power. This pin must have a 1.0 F (or greater) 20% (ESR <0.1 ) capacitor to VSS. VDD33 6 14 22 3.3 V Power and Regulator Input VSS ePad 6.2 Ground Pad. Buffer Type Descriptions Table 6.2 Buffer Type Descriptions BUFFER DESCRIPTION I Input. IPU Input with internal weak pull-up resistor. IS Input with Schmitt trigger. I/O12 Input/Output buffer with 12 mA sink and 12 mA source. I/O200 Input/Output buffer 12 mA with FET disabled, 100/200 mA source only when the FET is enabled. I/O12PD Input/Output buffer with 12 mA sink and 12 mA source with an internal weak pull-down resistor. I/O12PU Input/Output buffer with 12 mA sink and 12 mA source with a pull-up resistor. O12 Output buffer with 12 mA source. O12PU Output buffer with 12 mA sink and 12 mA source, with a pull-up resistor. O12PD Output buffer with 12 mA sink and 12 mA source, with a pull-down resistor. ICLKx XTAL clock input. OCLKx XTAL clock output. I/O-U Analog Input/Output as defined in the USB 2.0 Specification. I-R RBIAS. Revision 2.0 (10-14-09) 24 DATASHEET SMSC USB224x Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet Chapter 7 Pin Configurations 7.1 Card Reader The SMSC USB224x is fully compliant with the following flash media card reader specifications: Secure Digital 2.0 - HS-SD and SDHC - TransFlashTM and reduced form factor media MultiMediaCard 4.2 - 1/4/8 bit MMC Memory Stick 1.43 Memory Stick Pro Format 1.02 Memory Stick Pro-HG Duo Format 1.01 - Memory Stick, MS Duo, HS-MS, MS Pro-HG, MS Pro Memory Stick Duo 1.10 xD-Picture Card 1.2 7.2 System Configurations 7.2.1 EEPROM The USB224x can be configured via a 2-wire (I2C) EEPROM (512x8) flash device containing the options for the USB224x. If an external configuration device does not exist the internal default values will be used. If one of the external devices is used for configuration, the OEM can update the values through the USB interface. The device will then "attach" to the upstream USB host. The USBDM tool set is available in the USB224x/USB225x Card Reader software release package. To download the software package from SMSC's website, please visit: https://www2.smsc.com/mkt/CW_SFT_PUB.nsf/Agreements/OBJ+Card+Reader to go to the OBJ Card Reader Software Download Agreement. Review the license, and if you agree, check the "I agree" box and then select "Confirm". You will then be able to download the USB224x/USB225x Card reader combo release package zip file containing the USBDM tool set. Please note that the following applies to the system values and descriptions when used: 7.2.2 N/A = Not applicable to this part Reserved = For internal use EEPROM Data Descriptor Table 7.1 Internal Flash Media Controller Configurations ADDRESS REGISTER NAME DESCRIPTION INTERNAL DEFAULT VALUE 00h USB_SER_LEN USB Serial String Descriptor Length 1Ah 01h USB_SER_TYP USB Serial String Descriptor Type 03h 02h-19h USB_SER_NUM USB Serial Number "000000225001" (See Note 7.1) SMSC USB224x 25 DATASHEET Revision 2.0 (10-14-09) Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet Table 7.1 Internal Flash Media Controller Configurations (continued) ADDRESS REGISTER NAME DESCRIPTION INTERNAL DEFAULT VALUE 1Ah-1Bh USB_VID USB Vendor Identifier 0424 1Ch-1Dh USB_PID USB Product Identifier 2240 1Eh USB_LANG_LEN USB Language String Descriptor Length 04h 1Fh USB_LANG_TYP USB Language String Descriptor Type 03h 20h USB_LANG_ID_LSB USB Language Identifier Least Significant Byte 09h (See Note 7.2) 21h USB_LANG_ID_MSB USB Language Identifier Most Significant Byte 04h (See Note 7.2) 22h USB_MFR_STR_LEN USB Manufacturer String Descriptor Length 10h 23h USB_MFR_STR_TYP USB Manufacturer String Descriptor Type 03h 24h-31h USB_MFR_STR USB Manufacturer String "Generic" (See Note 7.1) 32h-5Dh Reserved - 00h 5Eh USB_PRD_STR_LEN USB Product String Descriptor Length 24h 5Fh USB_PRD_STR_TYP USB Product String Descriptor Type 03h 60h-99h USB_PRD_STR USB Product String "Ultra Fast Media Reader" (See Note 7.1) 9Ah USB_BM_ATT USB BmAttribute 80h 9Bh USB_MAX_PWR USB Max Power 30h (96 mA) 9Ch ATT_LB Attribute Lo byte 40h (Reverse SD_WP only) 9Dh ATT_HLB Attribute Hi Lo byte 00h 9Eh ATT_LHB Attribute Lo Hi byte 00h 9Fh ATT_HB Attribute Hi byte 00h A0h MS_PWR_LB Memory Stick Device Power Lo byte 08h A1h MS_PWR_HB Memory Stick Device Power Hi byte 00h A2h Reserved - 80h A3h Reserved - 00h A4h xD_PWR_LB xD-Picture Card Device Power Lo byte 00h A5h xD_PWR_HB xD-Picture Card Device Power Hi byte 08h Revision 2.0 (10-14-09) 26 DATASHEET SMSC USB224x Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet Table 7.1 Internal Flash Media Controller Configurations (continued) ADDRESS REGISTER NAME DESCRIPTION INTERNAL DEFAULT VALUE A6h SD_PWR_LB Secure Digital Device Power Lo byte 00h A7h SD_PWR_HB Secure Digital Device Power Hi byte 80h A8h LED_BLK_INT LED Blink Interval 02h A9h LED_BLK_DUR LED Blink After Access 28h AAh - B0h DEV0_ID_STR Device 0 Identifier String "COMBO" B1h - B7h DEV1_ID_STR Device 1 Identifier String "MS" B8h - BEh DEV2_ID_STR Device 2 Identifier String "SM" (See Note 7.3) BFh - C5h DEV3_ID_STR Device 3 Identifier String "SD/MMC" C6h - CDh INQ_VEN_STR Inquiry Vendor String "Generic" CEh-D2h INQ_PRD_STR Inquiry Product String 2240 D3h DYN_NUM_LUN Dynamic Number of LUNs FFh D4h - D7h DEV_LUN_MAP Device to LUN Mapping FFh, FFh, FFh, FFh D8h - DAh Reserved - 00h, 03h, 07h DBh - DDh Reserved - 5Ch, 56h, 97h DEh-FBh Not Applicable - 00h FCh-FFh NVSTORE_SIG Non-Volatile Storage Signature "ATA2" Note 7.1 This value is a UNICODE UTF-16LE encoded string value that meets the USB 2.0 specification (Revision 2.0, 2000). Values in double quotations without this note are ASCII values. Note 7.2 For a list of the most current 16-bit language ID's defined by the USB-IF, please visit http://www.unicode.org or consult The Unicode Standard, Worldwide Character Encoding, (Version 4.0), The Unicode Consortium, Addison-Wesley Publishing Company, Reading, Massachusetts. Note 7.3 The "SM" value will be overridden with "xD" once an xD-Picture Card has been identified. 7.2.3 EEPROM Data Descriptor Register Descriptions 7.2.3.1 00h: USB Serial String Descriptor Length BYTE NAME DESCRIPTION 0 USB_SER_LEN USB serial string descriptor length as defined by Section 9.6.7 "String" of the USB 2.0 Specification (Revision 2.0, 2000). This field is the "bLength" which describes the size of the string descriptor (in bytes). SMSC USB224x 27 DATASHEET Revision 2.0 (10-14-09) Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet 7.2.3.2 01h: USB Serial String Descriptor Type BYTE NAME DESCRIPTION 1 USB_SER_TYP USB serial string descriptor type as defined by Section 9.6.7 "String" of the USB 2.0 Specification (Revision 2.0, 2000). This field is the "bDescriptorType" which is a constant value associated with a string descriptor type. 7.2.3.3 02h-19h: USB Serial Number Option BYTE NAME 25:2 USB_SER_NUM 7.2.3.4 Maximum string length is 12 hex digits. Must be unique to each device. 1Ah-1Bh: USB Vendor ID Option BYTE NAME 1:0 USB_VID 7.2.3.5 DESCRIPTION DESCRIPTION This ID is unique for every vendor. The vendor ID is assigned by the USB Implementer's Forum. 1Ch-1Dh: USB Product ID Option BYTE NAME DESCRIPTION 1:0 USB_PID This ID is unique for every product. The product ID is assigned by the vendor. 7.2.3.6 1Eh: USB Language Identifier Descriptor Length BYTE NAME DESCRIPTION 0 USB_LANG_LEN USB language ID string descriptor length as defined by Section 9.6.7 "String" of the USB 2.0 Specification (Revision 2.0, 2000). This field is the "bLength" which describes the size of the string descriptor (in bytes). 7.2.3.7 1Fh: USB Language Identifier Descriptor Type BYTE NAME DESCRIPTION 1 USB_LANG_TYP USB language ID string descriptor type as defined by Section 9.6.7 "String" of the USB 2.0 Specification (Revision 2.0, 2000). This field is the "bDescriptorType" which is a constant value associated with a string descriptor type. 7.2.3.8 20h: USB Language Identifier Least Significant Byte BYTE NAME 2 USB_LANG_ID _LSB Revision 2.0 (10-14-09) DESCRIPTION English language code = `0409'. See Note 7.2 to reference additional language ID's defined by the USB-IF. 28 DATASHEET SMSC USB224x Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet 7.2.3.9 21h: USB Language Identifier Most Significant Byte BYTE NAME 3 USB_LANG_ID _MSB 7.2.3.10 DESCRIPTION English language code = `0409'. See Note 7.2 to reference additional language ID's defined by the USB-IF. 22h: USB Manufacturer String Descriptor Length BYTE NAME DESCRIPTION 0 USB_MFR_STR _LEN USB manufacturer string descriptor length as defined by Section 9.6.7 "String" of the USB 2.0 Specification (Revision 2.0, 2000). This field is the "bLength" which describes the size of the string descriptor (in bytes). 7.2.3.11 23h: USB Manufacturer String Descriptor Type BYTE NAME DESCRIPTION 1 USB_MFR_STR _TYP USB manufacturer string descriptor type as defined by Section 9.6.7 "String" of the USB 2.0 Specification (Revision 2.0, 2000). This field is the "bDescriptorType" which is a constant value associated with a string descriptor type. 7.2.3.12 24h-31h: USB Manufacturer String Option BYTE NAME 15:2 USB_MFR_STR 7.2.3.13 NAME 59:16 Reserved DESCRIPTION Reserved. 5Eh: USB Product String Descriptor Length BYTE NAME 0 USB_PRD_STR _LEN 7.2.3.15 The maximum string length is 29 characters. 32h-5Dh: Reserved BYTE 7.2.3.14 DESCRIPTION DESCRIPTION USB product string descriptor length as defined by Section 9.6.7 "String" of the USB 2.0 Specification (Revision 2.0, 2000). This field is the "bLength" which describes the size of the string descriptor (in bytes). Maximum string length is 29 characters 5Fh: USB Product String Descriptor Type BYTE NAME DESCRIPTION 1 USB_PRD_STR _TYP USB product string descriptor type as defined by Section 9.6.7 "String" of the USB 2.0 Specification (Revision 2.0, 2000). This field is the "bDescriptorType" which is a constant value associated with a string descriptor type. SMSC USB224x 29 DATASHEET Revision 2.0 (10-14-09) Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet 7.2.3.16 60h-99h: USB Product String Option BYTE NAME 59:2 USB_PRD_STR 7.2.3.17 DESCRIPTION This string will be used during the USB enumeration process in the Windows(R) operating system. Maximum string length is 29 characters. 9Ah: USB BmAttribute (1 byte) BIT NAME 7:0 USB_BM_ATT DESCRIPTION Self- or Bus-Power: Selects between self- and bus-powered operation. The hub is either self-powered (draws less than 2 mA of upstream bus power) or bus-powered (limited to a 100 mA maximum of upstream power prior to being configured by the host controller). When configured as a bus-powered device, the SMSC device consumes less than 100 mA of current prior to being configured. After configuration, the bus-powered SMSC device (along with all associated device circuitry, any embedded devices if part of a compound device, and 100 mA per externally available downstream port) must consume no more than 500 mA of upstream VBUS current. The current consumption is system dependent, and the OEM must ensure that the USB 2.0 Specification is not violated. When configured as a self-powered device, <1 mA of upstream VBUS current is consumed and all ports are available, with each port being capable of sourcing 500 mA of current. 80 = Bus-powered operation (default) C0 = Self-powered operation A0 = Bus-powered operation with remote wake-up E0 = Self-powered operation with remote wake-up 7.2.3.18 9Bh: USB MaxPower (1 byte) BIT NAME 7:0 USB_MAX_PWR Revision 2.0 (10-14-09) DESCRIPTION USB Max Power per the USB 2.0 Specification. Do NOT set this value greater than 100 mA. 30 DATASHEET SMSC USB224x Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet 7.2.3.19 9Ch-9Fh: Attribute Byte Descriptions BYTE BYTE NAME BIT 0 ATT_LB 3:0 4 DESCRIPTION Always reads `0'. Inquire Manufacturer and Product ID Strings `1' - Use the Inquiry Manufacturer and Product ID Strings. `0' (default) - Use the USB Descriptor Manufacturer and Product ID Strings. 5 Always reads `0'. 6 Reverse SD Card Write Protect Sense `1' (default) - SD cards will be write protected when SW_nWP is high, and writable when SW_nWP is low. `0' - SD cards will be write protected when SW_nWP is low, and writable when SW_nWP is high. 7 1 ATT_HLB 3:0 4 Reserved. Always reads `0'. Activity LED True Polarity `1' - Activity LED to Low True. `0' (default) - Activity LED polarity to High True. 5 Common Media Insert / Media Activity LED `1' - The activity LED will function as a common media inserted/media access LED. `0' (default) - The activity LED will remain in its idle state until media is accessed. 2 ATT_LHB 6 Always reads `0'. 7 Reserved. 0 Attach on Card Insert / Detach on Card Removal `1' - Attach on Insert is enabled. `0' (default) - Attach on Insert is disabled. 1 Always reads `0'. 2 Enable Device Power Configuration `1' - Custom Device Power Configuration stored in the NVSTORE is used. `0' (default) - Default Device Power Configuration is used. 3 ATT_HB SMSC USB224x 7:3 Always reads `0'. 6:0 Always reads `0'. 7 xD Player Mode 31 DATASHEET Revision 2.0 (10-14-09) Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet 7.2.4 A0h-A7h: Device Power Configuration The USB224x has one internal FET which can be utilized for card power. This section describes the default internal configuration. The settings are stored in NVSTORE and provide the following features: 1. A card can be powered by an external FET or by an internal FET. 2. The power limit can be set to 100 mA or 200 mA (Default) for the internal FET. Each media uses two bytes to store its device power configuration. Bit 3 selects between internal or external card power FET options. For internal FET card power control, bits 0 through 2 are used to set the power limit. The "Device Power Configuration" bits are ignored unless the "Enable Device Power Configuration" bit is set. See Section 7.2.3.19, "9Ch-9Fh: Attribute Byte Descriptions," on page 31. 7.2.4.1 A0h-A1h: Memory Stick Device Power Configuration FET TYPE BITS 0 FET Lo Byte MS_PWR_LB 3:0 Low Nibble 7:4 High Nibble 3:0 Low Nibble 0000b 0001b 1000b 1010b 7:4 High Nibble 0000b Disabled 1 2 FET Hi Byte MS_PWR_HB 3 7.2.4.2 DESCRIPTION 0000b Disabled Disabled External FET enabled Internal FET with 100 mA power limit Internal FET with 200 mA power limit A2h-A3h: Not Applicable BYTE NAME 1:0 Not Applicable 7.2.4.3 BIT TYPE DESCRIPTION Not applicable. A4h-A5h: xD-Picture Card Device Power Configuration When applicable, the "SM" value will be overridden with "xD" once an xD-Picture Card has been identified. FET TYPE BITS 0 FET Lo Byte xD_PWR_LB 3:0 Low Nibble 7:4 High Nibble 3:0 Low Nibble 0000b 0001b 1000b 1010b 7:4 High Nibble 0000b Disabled 1 2 FET Hi Byte xD_PWR_HB 3 Revision 2.0 (10-14-09) BIT TYPE DESCRIPTION 0000b Disabled 32 DATASHEET Disabled External FET enabled Internal FET with 100 mA power limit Internal FET with 200 mA power limit SMSC USB224x Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet 7.2.4.4 A6h-A7h: Secure Digital Device Power Configuration FET TYPE BITS 0 FET Lo Byte SD_PWR_LB 3:0 Low Nibble 7:4 High Nibble 3:0 Low Nibble 0000b 0001b 1000b 1010b 7:4 High Nibble 0000b Disabled 1 2 FET Hi Byte SD_PWR_HB 3 7.2.4.5 BIT TYPE DESCRIPTION 0000b Disabled Disabled External FET enabled Internal FET with 100 mA power limit Internal FET with 200 mA power limit A8h: LED Blink Interval BYTE NAME DESCRIPTION 0 LED_BLK_INT The blink rate is programmable in 50 ms intervals. The high bit (7) indicates an idle state: `0' - Off `1' - On The remaining bits (6:0) are used to determine the blink interval up to a max of 128 x 50 ms. 7.2.4.6 A9h: LED Blink Duration BYTE NAME 1 LED_BLK_DUR 7.2.5 DESCRIPTION LED Blink After Access. This byte is used to designate the number of seconds that the GPIO1 LED will continue to blink after a drive access. Setting this byte to "05" will cause the GPIO 1 LED to blink for 5 seconds after a drive access. Device ID Strings These bytes are used to specify the LUN descriptor returned by the device. These bytes are used in combination with the device to LUN mapping bytes in applications where the OEM wishes to reorder and rename the LUNs. If multiple devices are mapped to the same LUN (a COMBO LUN), then the CLUN#_ID_STR will be used to name the COMBO LUN instead of the individual device strings. When applicable, the "SM" value will be overridden with xD once an xD-Picture Card has been identified. 7.2.5.1 AAh-B0h: Device 0 Identifier String BYTE NAME 6:0 DEV0_ID_STR 7.2.5.2 DESCRIPTION Not applicable. B1h-B7h: Device 1 Identifier String BYTE NAME 6:0 DEV1_ID_STR SMSC USB224x DESCRIPTION This ID string is associated with the Memory Stick device. 33 DATASHEET Revision 2.0 (10-14-09) Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet 7.2.5.3 B8h-BEh: Device 2 Identifier String BYTE NAME 6:0 DEV2_ID_STR 7.2.5.4 DESCRIPTION This ID string is associated with the xD-Picture Card device. BFh-C5h: Device 3 Identifier String BYTE NAME DESCRIPTION 6:0 DEV3_ID_STR This ID string is associated with the Secure Digital / MultiMediaCard device. 7.2.5.5 C6h-CDh: Inquiry Vendor String BYTE NAME 7:0 INQ_VEN_STR 7.2.5.6 If bit 4 of the 1st attribute byte is set, the device will use these strings in response to a USB inquiry command, instead of the USB descriptor manufacturer and product ID strings. CEh-D2h: Inquiry Product String BYTE NAME 4:0 INQ_PRD_STR 7.2.5.7 DESCRIPTION DESCRIPTION If bit 4 of the 1st attribute byte is set, the device will use these strings in response to a USB inquiry command, instead of the USB descriptor manufacturer and product ID strings. D3h: Dynamic Number of LUNs BIT NAME DESCRIPTION 7:0 DYN_NUM_LUN These bytes are used to specify the number of LUNs the device exposes to the host. These bytes are also used for icon sharing by assigning more than one LUN to a single icon. This is used in applications where the device utilizes a combo socket and the OEM wishes to have only a single icon displayed for one or more interfaces. If this field is set to "FF", the program assumes that you are using the default value and icons will be configured per the default configuration. 7.2.5.8 D4h-D7h: Device to LUN Mapping BYTE NAME DESCRIPTION 3:0 DEV_LUN_MAP These registers map a device controller (SD/MMC, SM, and MS) to a Logical Unit Number (LUN). The device reports the mapped LUNs to the USB host in the USB descriptor during enumeration. The icon installer associates custom icons with the LUNs specified in these fields. Setting a register to "FF" indicates that the device is not mapped. Setting all of the DEV_LUN_MAP registers for all devices to "FF" forces the use of the default mapping configuration. Not all configurations are valid. Valid configurations depend on the hardware, packaging, and OEM board layout. The number of unique LUNs mapped must match the value in the Section 7.2.5.7, "D3h: Dynamic Number of LUNs," on page 34. Revision 2.0 (10-14-09) 34 DATASHEET SMSC USB224x Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet 7.2.5.9 D8h-FBh: Not Applicable BYTE NAME 35:0 Not Applicable 7.2.5.10 DESCRIPTION Not Applicable. FCh-FFh: Non-Volatile Storage Signature BYTE NAME DESCRIPTION 3:0 NVSTORE_SIG This signature is used to verify the validity of the data in the first 256 bytes of the configuration area. The signature must be set to `ATA2' for USB224x. 7.3 Default Configuration Option The SMSC device can be configured via its internal default configuration. Please see Section 7.2.2, "EEPROM Data Descriptor" for specific details on how to enable default configuration. Please refer to Table 7.1 for the internal default values that are loaded when this option is selected. 7.3.1 External Hardware RESET_N A valid hardware reset is defined as assertion of RESET_N for a minimum of 1 s after all power supplies are within operating range. While reset is asserted, the device (and its associated external circuitry) consumes less than 500 A of current from the upstream USB power source. Assertion of RESET_N (external pin) causes the following: 1. The PHY is disabled and the differential pair will be in a high-impedance state. 2. All transactions immediately terminate; no states are saved. 3. All internal registers return to the default state. 4. The external crystal oscillator is halted. 5. The PLL is halted. 6. The processor is reset. 7. All media interfaces are reset. 7.3.1.1 RESET_N for EEPROM Configuration Hardware reset asserted Device Recovery/ Stabilization 8051 Sets Configuration Registers Attach USB Upstream USB Reset recovery Idle Start completion request response t4 t1 t2 t3 t5 t6 t7 RESET_N VSS Figure 7.1 RESET_N Timing for EEPROM Mode SMSC USB224x 35 DATASHEET Revision 2.0 (10-14-09) Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet Table 7.2 RESET_N Timing for EEPROM Mode NAME DESCRIPTION MIN t1 RESET_N asserted t2 Device recovery/stabilization t3 8051 programs device configuration t4 USB attach t5 Host acknowledges attach and signals USB reset t6 USB idle t7 Ready to handle requests (with or without data) TYP MAX UNITS sec 1 20 500 sec 50 msec 100 msec 100 msec Undefined msec 5 msec Note: All power supplies must have reached the operating levels mandated in Chapter 9, DC Parameters, prior to (or coincident with) the assertion of RESET_N. 7.3.2 USB Bus Reset In response to the upstream port signaling a reset to the device, the device does the following: 1. Sets default address to `0'. 2. Sets configuration to: Unconfigured. 3. All transactions are stopped. 4. Processor reinitializes and restarts. 5. All media interfaces are disabled. Revision 2.0 (10-14-09) 36 DATASHEET SMSC USB224x Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet Chapter 8 Pin Reset States Hardware Initialization Voltage Signal (v) Firmware Operational RESET RESET VDD33 Time (t) VSS Figure 8.1 Pin Reset States Table 8.1 Legend for Pin Reset States Table 8.1 SYMBOL DESCRIPTION 0 Output driven low 1 Output driven high IP Input enabled PU Hardware enables pull-up PD Hardware enables pull-down -- Hardware disables function Z Hardware disables pad. Both output driver and input buffers are disabled. USB2240/40i/41/41i Pin Reset States Table 8.2 USB2240/40i/41/41i 36-Pin Reset States RESET STATE SMSC USB224x PIN PIN NAME FUNCTION INPUT/ OUTPUT PU/ PD 8 xD_D0 / SD_D6 / MS_D7 none z -- 7 xD_D1 / SD_D7 / MS_D6 none z -- 5 xD_D2 / SD_D0 / MS_D4 none z -- 4 xD_D3 / SD_D1 / MS_D5 none z -- 30 xD_D4 / GPIO6 (SD_WP) / MS_SCLK SD_WP 0 -- 25 xD_D5 / SD_D2 none z -- 26 GPIO15 (SD_nCD) GPIO IP pu 37 DATASHEET Revision 2.0 (10-14-09) Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet Table 8.2 USB2240/40i/41/41i 36-Pin Reset States (continued) RESET STATE PIN PIN NAME FUNCTION INPUT/ OUTPUT PU/ PD 24 GPIO12 (MS_INS) GPIO IP pu 23 xD_D6 / SD_D3 / MS_D3 none z -- 20 xD_D7 / SD_D4 / MS_D2 none z -- 9 xD_nWP / SD_CLK / MS_BS none z -- 10 xD_ALE / SD_D5 / MS_D1 none z -- 11 xD_CLE / SD_CMD / MS_D0 none z -- 19 GPIO14 (xD_nCD) GPIO IP pu 1 GPIO1 (LED) GPIO 0 -- 16 xD_nRE none z -- 27 GPIO2 / RXD / SDA GPIO 0 -- 29 GPIO4 GPIO 0 -- 31 GPIO7 / TXD / SCK / MS_SKT_SEL GPIO 0 -- 21 GPIO10 (CRD_PWR) GPIO z -- 28 TEST TEST IP -- 18 RESET_N RESET_N IP -- 12 xD_nWE none z -- 17 xD_nB/R none z -- 15 xD_nCE none z -- 2 USB+ USB+ z -- 3 USB- USB- z -- Note: xD signals only apply to USB2240/USB2240i. 8.2 USB2242/42i Pin Reset States Table 8.3 USB2242/42i 36-Pin Reset States POST-RESET STATE MS MODE RESET STATE PIN PIN NAME FUNCTION INPUT / OUTPUT PU/ PD FUNCTION OUTPUT PU/ PD INPUT 8 MS_D7 none z -- MS_D7 hw pd yes Revision 2.0 (10-14-09) 38 DATASHEET SMSC USB224x Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet POST-RESET STATE MS MODE RESET STATE PIN PIN NAME FUNCTION INPUT / OUTPUT PU/ PD FUNCTION OUTPUT PU/ PD INPUT 7 MS_D6 none z -- MS_D6 hw pd yes 5 MS_D4 none z -- MS_D4 hw pd yes 4 MS_D5 none z -- MS_D5 hw hw yes 30 MS_SCLK SD_WP 0 -- MS_SCLK hw hw -- 25 NC none z -- none z -- -- 23 MS_D3 none z -- MS_D3 hw pd yes 20 MS_D2 none z -- MS_D2 hw pd yes 9 MS_BS none z -- MS_BS hw hw -- 10 MS_D1 none z -- MS_D1 hw hw yes 11 MS_D0 none z -- MS_D0 hw pd yes 19 GPIO14 GPIO IP pu 26 GPIO15 GPIO IP pu 24 GPIO12 (MS_INS) GPIO IP pu 27 GPIO2 / RXD / SDA GPIO 0 -- 29 GPIO4 GPIO 0 -- 31 GPIO7 / TXD / SCK / MS_SKT_SEL GPIO 0 -- 21 GPIO10 (CRD_PWR) GPIO z -- 28 TEST TEST IP -- 18 RESET_N RESET_N IP -- 1 GPIO1 (LED) GPIO 0 -- 16 NC none z -- none z -- -- 12 NC none z -- none z -- -- 17 NC none z -- none z -- -- 15 NC none z -- none z -- -- 2 USB+ USB+ z -- 3 USB- USB- z -- 35 RBIAS 33 XTAL1 (CLKIN) 32 XTAL2 SMSC USB224x 39 DATASHEET Revision 2.0 (10-14-09) Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet 8.3 USB2244/44i Pin Reset States Table 8.4 USB2244/USB2244i 36-Pin Reset States Post-Reset State SD Mode RESET STATE PIN NAME FUNCTION INPUT / OUTPUT PU/ PD FUNCTION OUTPUT PU/ PD INPUT 8 SD_D6 none z -- SD_D6 hw pu yes 7 SD_D7 none z -- SD_D7 hw pu yes 5 SD_D0 none z -- SD_D0 hw pu yes 4 SD_D1 none z -- SD_D1 hw pu yes 30 SD_WP SD_WP 0 -- SD_WP (fw) (fw) (fw) 25 SD_D2 none z -- SD_D2 hw pu yes 23 SD_D3 none z -- SD_D3 hw pu yes 20 SD_D4 none z -- SD_D4 hw pu yes 9 SD_CLK none z -- SD_CLK hw -- yes 10 SD_D5 none z -- SD_D5 hw pu yes 11 SD_CMD none z -- SD_CMD hw pu yes 19 GPIO14 GPIO IP pu 26 GPIO15 (SD_nCD) GPIO IP pu 24 GPIO12 GPIO IP pu 27 GPIO2 / RXD / SDA GPIO 0 -- RXD z pu yes 29 GPIO4 GPIO 0 -- 31 GPIO7 / TXD / SCK GPIO 0 -- TXD hw -- -- 21 GPIO10 (CRD_PWR) GPIO z -- PWR VDD -- -- 28 TEST TEST IP -- 18 RESET_N RESET_N IP -- 1 GPIO1 (LED) GPIO 0 -- 17:15 NC none z -- none z -- -- 12 NC none z -- none z -- -- 2 USB+ USB+ z -- 3 USB- USB- z -- 35 RBIAS 33 XTAL1 (CLKIN) 32 XTAL2 PIN Revision 2.0 (10-14-09) 40 DATASHEET SMSC USB224x Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet Chapter 9 DC Parameters 9.1 Maximum Guaranteed Ratings PARAMETER SYMBOL MIN Storage Temperature TA -55 MAX UNITS 150 C Lead Temperature C 3.3 V supply voltage VDD33 COMMENTS -0.5 4.0 V Voltage on USB+ and USB- pins -0.5 (3.3 V supply voltage + 2) 6 V Voltage on GPIO10 -0.5 VDD33 + 0.3 V Voltage on any signal pin -0.5 VDD33 + 0.3 V Voltage on XTAL1 -0.5 3.6 V Voltage on XTAL2 -0.5 VDD18 + 0.3 V Please refer to JEDEC specification J-STD-020D. When internal power FET operation of this pin is enabled, this pin may be simultaneously shorted to ground or any voltage up to 3.63 V indefinitely, without damage to the device as long as VDD33 and VDDA33 are less than 3.63 V and TA is less than 70oC. Note 9.1 Stresses above the specified parameters may cause permanent damage to the device. This is a stress rating only and functional operation of the device at any condition above those indicated in the operation sections of this specification is not implied. Note 9.2 When powering this device from laboratory or system power supplies, it is important that the absolute maximum ratings not be exceeded or device failure can result. Some power supplies exhibit voltage spikes on their outputs when the AC power is switched on or off. In addition, voltage transients on the AC power line may appear on the DC output. When this possibility exists, it is suggested that a clamp circuit be used. Voltage tRT VDD33 3.3 V 100% 90% VSS 10% t90% t10% Time Figure 9.1 Supply Rise Time Model SMSC USB224x 41 DATASHEET Revision 2.0 (10-14-09) Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet 9.2 Operating Conditions PARAMETER SYMBOL MIN MAX UNITS COMMENTS Commercial Part TA 0 70 C Operating Temperature Industrial Part TA -40 85 C Ambient temperature in still air. 3.3 V supply voltage VDD33 3.0 3.6 V (Note 9.3) 3.3 V supply rise time tRT 0 400 s -0.3 5.5 V Voltage on USB+ and USB- pins If any 3.3 V supply voltage drops below 3.0 V, then the MAX becomes: (3.3 V supply voltage) + 0.5 5.5 Voltage on any signal pin -0.3 VDD33 V Voltage on XTAL1 -0.3 VDD33 V Voltage on XTAL2 -0.3 VDD18 V Note 9.3 9.3 A 3.3 V regulator with an output tolerance of 1% must be used if the output of the internal power FETs must support a 5% tolerance. DC Electrical Characteristics PARAMETER SYMBOL MIN TYP MAX UNITS 0.8 V COMMENTS I, IPU, IPD Type Input Buffer Low Input Level VILI High Input Level VIHI Pull Down PD 72 A Pull Up PU 58 A 2.0 TTL Levels V IS Type Input Buffer Low Input Level VILI High Input Level VIHI Hysteresis 0.8 2.0 VHYSI V TTL Levels V 420 mV ICLK Input Buffer Low Input Level VILCK High Input Level VIHCK 1.4 IIL -10 Input Leakage Revision 2.0 (10-14-09) 0.5 42 DATASHEET V V +10 A VIN = 0 to VDD33 SMSC USB224x Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet PARAMETER SYMBOL MIN Low Input Leakage IIL High Input Leakage IIH TYP MAX UNITS COMMENTS -10 +10 A VIN = 0 -10 +10 A VIN = VDD33 0.4 V IOL = 12 mA @ VDD33= 3.3 V V IOH = -12 mA @ VDD33= 3.3 V +10 A VIN = 0 to VDD33 (Note 9.4) 0.4 V IOL = 12 mA @ VDD33= 3.3 V V IOH = -12 mA @ VDD33= 3.3 V A VIN = 0 to VDD33 (Note 9.4) Input Leakage (All I and IS buffers) O12 Type Buffer Low Output Level VOL High Output Level VOH VDD33 - 0.4 Output Leakage IOL -10 I/O12, I/O12PU & I/O12PD Type Buffer Low Output Level VOL High Output Level VOH VDD33 - 0.4 Output Leakage IOL -10 Pull Down PD 72 A Pull Up PU 58 A +10 IO-U (Note 9.5) I-R (Note 9.6) I/O200 Integrated Power FET for GPIO10 High Output Current Mode IOUT 200 mA VdropFET = 0.46 V Low Output Current Mode (Note 9.7) IOUT 100 mA VdropFET = 0.23 V On Resistance (Note 9.7) RDSON 2.1 IFET = 70 mA Output Voltage Rise Time tDSON 800 s CLOAD = 10 F SMSC USB224x 43 DATASHEET Revision 2.0 (10-14-09) Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet PARAMETER SYMBOL TYP MAX UNITS ICCINIT 80 90 mA ICC 110 140 mA ICC 135 165 mA Supply Current Suspend ICSBY 350 700 A Industrial Temperature Suspend ICSBYI 350 900 A Supply Current Unconfigured Supply Current Active Full Speed High Speed 9.4 MIN COMMENTS Note 9.4 Output leakage is measured with the current pins in high impedance. Note 9.5 See The USB 2.0 Specification, Chapter 7, for USB DC electrical characteristics Note 9.6 RBIAS is a 3.3 V tolerant analog pin. Note 9.7 Output current range is controlled by program software, software disables FET during short circuit condition. Note 9.8 The assignment of each Integrated Card Power FET to a designated Card Connector is controlled by both firmware and the specific board implementation. Firmware will default to the settings listed in Table 11.1, "USB2240/40i and USB2241/41i GPIO Usage," on page 48. Note 9.9 The 3.3 V supply should be at least at 75% of its operating condition before the 1.8 V supply is allowed to ramp up. Capacitance TA = 25C; fc = 1 MHz; VDD, VDDP = 1.8 V Table 9.1 Pin Capacitance LIMITS PARAMETER Clock Input Capacitance Input Capacitance Output Capacitance Revision 2.0 (10-14-09) SYMBOL MIN TYP MAX UNIT TEST CONDITION CXTAL 2 pF All pins (except USB pins and pins under test) are tied to AC ground. CIN 10 pF COUT 20 pF 44 DATASHEET SMSC USB224x Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet 9.5 Package Thermal Specifications Table 9.2 36-Pin QFN Package Thermal Parameters PARAMETER Thermal Resistance VELOCITY (meters/sec) SYMBOL UNIT 33.2 0 JA 1 Junction-to-Top-of-Package VALUE 29 2 26 0 2.6 JT 1 2 2.6 C/W C/W 2.6 Note 9.10 Thermal parameters are measured or estimated for devices with the exposed pad soldered to thermal vias in a multilayer 2S2P PCB per JESD51. Thermal resistance is measured from the die to the ambient air. SMSC USB224x 45 DATASHEET Revision 2.0 (10-14-09) Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet Chapter 10 AC Specifications 10.1 Oscillator/Crystal Parallel Resonant, Fundamental Mode, 24 MHz 350 ppm. XTAL1 (CS1 = CB1 + CXTAL1 ) C1 Crystal C0 1M CL C2 XTAL2 (CS2 = CB2 + CXTAL2 ) Figure 10.1 Typical Crystal Circuit Table 10.1 Crystal Circuit Legend SYMBOL DESCRIPTION IN ACCORDANCE WITH C0 Crystal shunt capacitance CL Crystal load capacitance CB Total board or trace capacitance OEM board design CS Stray capacitance SMSC IC and OEM board design CXTAL XTAL pin input capacitance SMSC IC C1 Load capacitors installed on OEM board Calculated values based on Figure 10.2, "Capacitance Formulas" (See Note 10.2) C2 Crystal manufacturer's specification (See Note 10.1) C1 = 2 x (CL - C0) - CS1 C2 = 2 x (CL - C0) - CS2 Figure 10.2 Capacitance Formulas Note 10.1 C0 is usually included (subtracted by the crystal manufacturer) in the specification for CL and should be set to `0' for use in the calculation of the capacitance formulas in Figure 10.2, "Capacitance Formulas". However, the OEM PCB itself may present a parasitic capacitance between XTAL1 and XTAL2. For an accurate calculation of C1 and C2, take the parasitic capacitance between traces XTAL1 and XTAL2 into account. Note 10.2 Each of these capacitance values is typically approximately 18 pF. Revision 2.0 (10-14-09) 46 DATASHEET SMSC USB224x Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet 10.2 Ceramic Resonator 24 MHz 350 ppm XTAL1 24 MHz Ceramic Resonator 1M XTAL2 Figure 10.3 Ceramic Resonator Usage with SMSC IC 10.3 External Clock 50% Duty cycle 10%, 24 MHz 350 ppm, Jitter < 100 ps rms. The external clock is recommended to conform to the signaling level designated in the JESD76-2 specification on 1.8 V CMOS Logic. XTAL2 should be treated as a no connect. SMSC USB224x 47 DATASHEET Revision 2.0 (10-14-09) Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet Chapter 11 GPIO Usage Table 11.1 USB2240/40i and USB2241/41i GPIO Usage NAME ACTIVE LEVEL SYMBOL DESCRIPTION AND NOTE GPIO1 H LED LED indicator GPIO2 H RXD / SDA Receive Port of Debugger / Serial EEPROM Data GPIO4 USER GPIO User defined GPIO6 L SD_WP SD Write Protect Detection GPIO7 H TXD / SCK / MS_SKT_SEL Transmit Port of Debugger / Serial EEPROM Clock / Memory Stick Socket (1 = 8-bit; 0 = 4-bit) GPIO10 L CRD_PWR Card Power Control GPIO12 L MS_INS Memory Stick Card Insertion GPIO14 L xD_nCD xD-Picture Card detect (USB2240/40i only ) GPIO15 L SD_nCD Secure Digital card detect Table 11.2 USB2242/42i GPIO Usage NAME ACTIVE LEVEL SYMBOL DESCRIPTION AND NOTE GPIO1 H LED LED indicator GPIO2 H RXD / SDA Receive Port of Debugger / Serial EEPROM Data GPIO4 USER GPIO User defined GPIO6 L SD_WP SD Write Protect Detection GPIO7 H TXD / SCK / MS_SKT_SEL Transmit Port of Debugger / Serial EEPROM Clock / Memory Stick Socket (1 = 8-bit; 0 = 4-bit) GPIO10 L CRD_PWR Card Power Control GPIO12 L MS_INS Memory Stick Card Insertion GPIO14 USER GPIO User defined GPIO15 USER GPIO User defined Table 11.3 USB2244/44i GPIO Usage NAME ACTIVE LEVEL GPIO1 H LED LED indicator GPIO2 H RXD / SDA Receive Port of Debugger / Serial EEPROM Data Revision 2.0 (10-14-09) SYMBOL 48 DATASHEET DESCRIPTION AND NOTE SMSC USB224x Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet Table 11.3 USB2244/44i GPIO Usage (continued) GPIO4 USER GPIO User defined GPIO6 L SD_WP SD Write Protect Detection GPIO7 H TXD / SCK / MS_SKT_SEL Transmit Port of Debugger / Serial EEPROM Clock / Memory Stick Socket (1 = 8-bit; 0 = 4-bit) GPIO10 L CRD_PWR Card Power Control GPIO12 USER GPIO User defined GPIO14 USER GPIO User defined GPIO15 L SD_nCD Secure Digital card detect SMSC USB224x 49 DATASHEET Revision 2.0 (10-14-09) Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet Chapter 12 Package Outline Figure 12.1 USB224x 36-QFN, 6x6 mm Body, 0.5 mm Pitch Table 12.1 Package Parameters SYMBOL MIN NOMINAL MAX NOTE REMARKS A A1 A2 A3 D/E D1/E1 D2/E2 L b e 0.80 0 0.60 ~ 0.02 ~ 0.20 REF 6.00 ~ 4.10 0.60 0.25 0.50 BSC 1.00 0.05 0.80 2 2 - Overall Package Height Standoff Mold Thickness Leadframe Thickness X/Y Overall Body Size X/Y Mold Cap Size X/Y Exposed Pad Size Terminal Length Terminal Width Terminal Pitch 5.85 5.55 4.00 0.50 0.18 6.15 5.95 4.20 0.75 0.30 Note 12.1 All dimensions are in millimeters. Note 12.2 Position tolerance of each terminal and exposed pad is 0.05 mm at maximum material condition. Note 12.3 Dimension "b" applies to plated terminals and is measured between 0.15 mm and 0.30 mm from the terminal tip. Revision 2.0 (10-14-09) 50 DATASHEET SMSC USB224x Ultra Fast USB 2.0 Multi-Format, SD/MMC, and MS Flash Media Controllers Datasheet Note 12.4 Details of terminal #1 identifier are optional but must be located within the area indicated. Note 12.5 Coplanarity zone applies to exposed pad and terminals. Figure 12.2 Additional Package Information and Notes SMSC USB224x 51 DATASHEET Revision 2.0 (10-14-09)