TSC2000 TSC 200 0 (R) SBAS257 - FEBRUARY 2002 PDA ANALOG INTERFACE CIRCUIT FEATURES APPLICATIONS PERSONAL DIGITAL ASSISTANTS CELLULAR PHONES MP3 PLAYERS 4-WIRE TOUCH SCREEN INTERFACE RATIOMETRIC CONVERSION SINGLE 2.7V TO 3.6V SUPPLY SERIAL INTERFACE INTERNAL DETECTION OF SCREEN TOUCH PROGRAMMABLE 8-, 10-, OR 12-BIT RESOLUTION PROGRAMMABLE SAMPLING RATES DESCRIPTION DIRECT BATTERY MEASUREMENT (0.5V to 6V) ON-CHIP TEMPERATURE MEASUREMENT TOUCH-PRESSURE MEASUREMENT FULL POWER-DOWN CONTROL TSSOP-20 PACKAGE The TSC2000 is a complete PDA analog interface circuit. It contains a complete 12-bit, Analog-to-Digital (A/D) resistive touch screen converter including drivers, the control to measure touch pressure, and an 8-bit Digital-to-Analog (D/A) converter output for LCD contrast control. The TSC2000 interfaces to the host controller through a standard SPITM serial interface. The TSC2000 offers programmable resolution and sampling rates from 8- to 12-bits and up to 125kHz to accommodate different screen sizes. The TSC2000 also offers two battery-measurement inputs, one of which is capable of reading battery voltages up to 6V while operating at only 2.7V. It also has an on-chip temperature sensor capable of reading 0.3C resolution. The TSC2000 is available in a TSSOP-20 package. SPI is a registered trademark of Motorola. US Patent No. 624639. MISO X+ X- Y+ Y- SS Clock Touch Panel Drivers Serial Interface and Control Logic Temp Sensor SCLK MOSI A/D Converter VBAT1 Battery Monitor VBAT2 Battery Monitor DAV MUX PENIRQ AUX1 AUX2 Internal 2.5V Reference VREF ARNG AOUT D/A Converter Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright (c) 2002, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. www.ti.com ABSOLUTE MAXIMUM RATINGS(1) ELECTROSTATIC DISCHARGE SENSITIVITY VDD to GND ........................................................................... -0.3V to +6V Digital Input Voltage to GND ................................... -0.3V to VDD + 0.3V Operating Temperature Range ...................................... -40C to +105C Storage Temperature Range ......................................... -65C to +150C Junction Temperature (TJ Max) .................................................... +150C TSSOP Package Power Dissipation .................................................... (TJ Max - TA)/JA JA Thermal Impedance .......................................................... 93C/W Lead Temperature, Soldering Vapor Phase (60s) ............................................................ +215C Infrared (15s) ..................................................................... +220C This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. NOTE: (1) Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. Exposure to absolute maximum conditions for extended periods may affect device reliability. INTEGRAL LINEARITY PACKAGE ERROR (LSB) PACKAGE-LEAD DESIGNATOR(1) PRODUCT SPECIFIED TEMPERATURE RANGE PACKAGE MARKING ORDERING NUMBER(2) TRANSPORT MEDIA, QUANTITY TSC2000IPW 2 TSSOP-20 PW -40C to +85C TSC2000I TSC2000IPW Rails, 70 " " " " " " TSC2000IPWR Tape and Reel, 2000 NOTES: (1) For the most current specifications and package information, refer to our web site at www.ti.com. (2) Models labeled with "R" indicates large quantity tape and reel. PIN DESCRIPTION PIN CONFIGURATION Top View TSSOP +VDD 1 20 AUX1 X+ 2 19 AUX2 Y+ 3 18 ARNG X- 4 17 AOUT Y- 5 16 PENIRQ TSC2000 2 GND 6 15 MISO VBAT1 7 14 DAV VBAT2 8 13 MOSI VREF 9 12 SS NC 10 11 SCLK PIN NAME 1 2 3 VDD X+ Y+ 4 5 6 7 8 9 10 11 12 X- Y- GND VBAT1 VBAT2 VREF NC SCLK SS 13 MOSI 14 15 DAV MISO 16 PENIRQ 17 18 19 20 AOUT ARNG AUX2 AUX1 DESCRIPTION Power Supply X+ Position Input Y+ Position Input X- Position Input Y- Position Input Ground Battery Monitor Input 1 Battery Monitor Input 2 Voltage Reference Input/Output No Connection Serial Clock Input Slave Select Input (Active LOW). Data will not be clocked in to MOSI unless SS is LOW. When SS is HIGH, MISO is high impedance. Serial Data Input. Data is clocked in at SCLK falling edge. Data Available (Active LOW) Serial Data Output. Data is clocked out at SCLK falling edge. High impedance when SS is HIGH. Pen Interrupt Analog Output Current from D/A Converter D/A Converter Analog Output Range Set Auxiliary A/D Converter Input 2 Auxiliary A/D Converter Input 1 TSC2000 www.ti.com SBAS257 ELECTRICAL CHARACTERISTICS At -40C to +85C, +VDD = +2.7V, internal VREF = +2.5V, conversion clock = 2MHz, 12-bit mode, unless otherwise noted. TSC2000IPW PARAMETER CONDITIONS AUXILIARY ANALOG INPUT Input Voltage Range Input Capacitance Input Leakage Current BATTERY MONITOR INPUT Input Voltage Range Input Voltage Range Input Capacitance Input Leakage Current Accuracy D/A CONVERTER Output Current Range Resolution Integral Linearity VOLTAGE REFERENCE Voltage Range Reference Drift External Reference Input Range Current Drain DIGITAL INPUT/OUTPUT Internal Clock Frequency Logic Family Logic Levels: VIH VIL VOH VOL POWER-SUPPLY REQUIREMENTS Power-Supply Voltage, +VDD Quiescent Current TYP 0 MAX UNITS +VREF V pF A 6.0 3.0 V V pF A % 25 1 VBAT1 VBAT2 0.5 0.5 25 1 -3 TEMPERATURE MEASUREMENT Temperature Range Temperature Resolution Accuracy A/D CONVERTER Resolution No Missing Codes Integral Linearity Offset Error Gain Error Noise Power-Supply Rejection MIN +3 -40 +85 C C C 12 2 6 6 Bits Bits LSB LSB LSB Vrms dB 8 A Bits LSB 0.3 2 Programmable: 8-, 10-, or 12-Bits 12-Bit Resolution 11 Excluding Reference Error 30 80 Set by Resistor from ARNG to GND 650 2 Internal 2.5V Internal 1.25V 2.45 1.225 2.5 1.25 20 1.0 External Reference 2.55 1.275 VDD 20 8 CMOS IIH = +5A IIL = +5A IOH = 2 TTL Loads IOL = 2 TTL Loads 0.7VDD -0.3 0.8VDD Specified Performance See Note (1) See Note (2) Power Down 2.7 TEMPERATURE RANGE Specified Performance MHz 0.3VDD 0.4 1.25 500 -40 V V ppm/C V A 3.6 2.3 V V V V 3 V mA A A +85 C NOTES: (1) AUX1 conversion, no averaging, no REF power down, 50s conversion. (2) AUX1 conversion, no averaging, external reference, 50s conversion. TSC2000 SBAS257 www.ti.com 3 TIMING CHARACTERISTICS(1)(2) At -40C to +85C, +VDD = +2.7V, VREF = +2.5V, unless otherwise noted. TSC2000 PARAMETER SCLK Period Enable Lead Time Enable Lag Time Sequential Transfer Delay Data Setup Time Data Hold Time (inputs) Data Hold Time (outputs) Slave Access Time Slave DOUT Disable Time DataValid Rise Time Fall Time CONDITIONS MIN tsck tLead tLag ttd tsu thi tho ta tdis tv tr tf 30 15 15 30 10 10 0 TYP MAX UNITS 15 15 10 30 30 ns ns ns ns ns ns ns ns ns ns ns ns NOTES: (1) All input signals are specified with tr = tf = 5ns (10% to 90% of VDD) and timed from a voltage level of (VIL + VIH)/2. (2) See timing diagram below. TIMING DIAGRAM All specifications typical at -40C to +85C, +VDD = +2.7V. SS ttd tLag tsck tLead twsck tf tr twsck SCLK tv tho MSB OUT MISO tdis BIT 6 ... 1 LSB OUT BIT 6 ... 1 LSB IN ta tsu MOSI 4 MSB IN thi TSC2000 www.ti.com SBAS257 TYPICAL CHARACTERISTICS At TA = +25C, +VDD = +2.7V, conversion clock = 2MHz, 12-bit mode. Internal VREF = +2.5V, unless otherwise noted. CONVERSION SUPPLY CURRENT vs TEMPERATURE (AUX1 Conversion, No Averaging, No REF Power-Down, 20s Conversion) POWER-DOWN SUPPLY CURRENT vs TEMPERATURE 7 2 6 1.95 1.9 IDD (nA) IDD (mA) 5 1.85 4 3 2 1.8 1 0 1.75 -60 -40 -20 0 20 40 60 80 -60 100 -40 -20 POWER-DOWN SUPPLY CURRENT vs SUPPLY VOLTAGE 40 60 80 100 INTERNAL OSCILLATOR FREQUENCY vs VDD Internal Oscillator Frequency (MHz) 0.11 0.1 0.09 0.08 0.07 8.25 8.2 8.15 8.1 8.05 8 7.95 7.9 7.85 7.8 0.06 2.5 2.9 2.7 3.1 3.3 3.5 2.5 3.7 2.7 3.1 2.9 Supply Voltage (V) 3.3 3.5 3.7 VDD (V) CHANGE IN GAIN ERROR vs TEMPERATURE CHANGE IN OFFSET ERROR vs TEMPERATURE 0.5 0.5 0.4 0.4 0.3 0.3 Change in Offset (LSB) Change in Gain Error (LSB) 20 8.3 0.12 Power-Down Current (nA) 0 Temperature (C) Temperature (C) 0.2 0.1 0 -0.1 -0.2 -0.3 0.2 0.1 0 -0.1 -0.2 -0.3 -0.4 -0.4 -0.5 -0.5 -60 -40 -20 0 20 40 60 80 -60 100 TSC2000 SBAS257 -40 -20 0 20 40 60 80 100 Temperature (C) Temperature (C) www.ti.com 5 TYPICAL CHARACTERISTICS (Cont.) At TA = +25C, +VDD = +2.7V, conversion clock = 2MHz, 12-bit mode. Internal VREF = +2.5V, unless otherwise noted. INTERNAL REFERENCE vs VDD INTERNAL REFERENCE vs TEMPERATURE 2.55 1.275 2.54 1.27 2.54 1.27 2.53 1.265 2.53 1.265 1.26 2.52 VREF (V) 2.51 1.255 2.5 1.25 2.5V Reference 2.49 1.245 1.26 1.25V Reference 2.51 1.25 2.5V Reference 2.49 1.245 2.48 1.24 2.48 1.24 2.47 1.235 2.47 1.235 2.46 1.23 2.46 1.23 1.225 2.45 2.45 -60 -40 -20 0 20 40 60 80 2.7 2.9 3.3 3.5 3.7 VDD (V) INTERNAL OSCILLATOR FREQUENCY vs TEMPERATURE TOUCHSCREEN DRIVER ON-RESISTANCE vs TEMPERATURE 8 7.5 8.2 7 8 7.8 7.6 6.5 6 5.5 5 7.4 4.5 7.2 4 -60 -40 -20 0 20 40 60 80 100 -60 -40 -20 Temperature (C) 0 20 40 60 80 100 Temperature (C) TEMP1 DIODE VOLTAGE vs TEMPERATURE TOUCH SCREEN DRIVER ON-RESISTANCE vs VDD 7 800 6.9 750 6.8 700 6.7 Voltage (mV) On-Resistance () 3.1 Temperature (C) Resistance () Internal Oscillator Frequency (MHz) 1.225 2.5 100 8.4 6.6 6.5 6.4 650 600 550 6.3 500 6.2 450 6.1 400 2.5 2.7 2.9 3.1 3.3 3.5 3.7 -60 Supply Voltage (V) 6 1.255 2.5 -40 -20 0 20 40 60 80 100 Temperature (C) TSC2000 www.ti.com SBAS257 VREF (V) 1.25V Reference 2.52 VREF (V) 1.275 VREF (V) 2.55 TYPICAL CHARACTERISTICS (Cont.) At TA = +25C, +VDD = +2.7V, conversion clock = 2MHz, 12-bit mode. Internal VREF = +2.5V, unless otherwise noted. TEMP1 DIODE VOLTAGE vs VDD TEMP2 DIODE VOLTAGE vs TEMPERATURE 900 612.0 611.8 611.6 TEMP1 Voltage (mV) Voltage (mV) 800 700 600 611.4 611.2 611.0 610.8 610.6 610.4 610.2 500 -60 610.0 -40 -20 0 20 40 60 80 100 2.5 2.7 3.1 2.9 TEMP2 DIODE VOLTAGE vs VDD 3.5 3.7 DAC OUTPUT CURRENT vs TEMPERATURE 740 1 738 0.95 DAC Output Current (mA) 736 Temp2 Voltage (mV) 3.3 VDD (V) Temperature (C) 734 732 730 728 726 724 0.9 0.85 0.8 0.75 0.7 0.65 722 720 0.6 2.5 2.7 2.9 3.1 3.5 3.3 3.7 -60 -40 -20 0 VDD (V) 20 40 60 80 100 Temperature (C) DAC MAX CURRENT vs VDD 0.91 DAC Output Current (mA) 0.905 0.9 0.895 0.89 0.885 0.88 0.875 2.5 2.7 2.9 3.1 3.3 3.5 3.7 VDD (V) TSC2000 SBAS257 www.ti.com 7 OVERVIEW The TSC2000 is an analog interface circuit for human interface devices. A register-based architecture eases integration with microprocessor-based systems through a standard SPI bus. All peripheral functions are controlled through the registers and onboard state machines. The TSC2000 consists of the following blocks (refer to the block diagram on the front page): * Touch Screen Interface Control of the TSC2000 and its functions is accomplished by writing to different registers in the TSC2000. A simple command protocol is used to address the 16-bit registers. Registers control the operation of the A/D converter and D/A converter. The result of measurements made will be placed in the TSC2000's memory map and may be read by the host at any time. Three signals are available from the TSC2000 to indicate that data is available for the host to read. The DAV output indicates that an A/D conversion has completed and that data is available. The PENIRQ output indicates that a touch has been detected on the touch screen. A typical application of the TSC2000 is shown in Figure 1. * Battery Monitors * Auxiliary Inputs * Temperature Monitor * Current Output D/A Converter Voltage Regulator 1F + to 10F (Optional) +2.7V to +3.3V LCD Contrast 0.1F Touch Screen 1F + to 10F (Optional) Communication to the TSC2000 is via a standard SPI serial interface. This interface requires that the Slave Select signal be driven LOW to communicate with the TSC2000. Data is then shifted into or out of the TSC2000 under control of the host microprocessor, which also provides the serial data clock. 0.1F Main Battery TSC2000 1 +VDD AUX1 20 Auxiliary Input 2 X+ AUX2 19 Auxiliary Input 3 Y+ ARNG 18 4 X- AOUT 17 5 Y- PENIRQ 16 Pen Interrupt Request 6 GND MISO 15 Serial Data Out 7 VBAT1 DAV 14 Data Available 8 VBAT2 MOSI 13 Serial Data In 9 VREF SS 12 Slave Select 10 NC SCLK 11 Serial Clock Secondary Battery RRNG FIGURE 1. Typical Circuit Configuration. 8 TSC2000 www.ti.com SBAS257 OPERATION--TOUCH SCREEN A resistive touch screen works by applying a voltage across a resistor network and measuring the change in resistance at a given point on the matrix where a screen is touched by an input stylus, pen, or finger. The change in the resistance ratio marks the location on the touch screen. The TSC2000 supports the resistive 4-wire configurations (see Figure 1). The circuit determines location in two coordinate pair dimensions, although a third dimension can be added for measuring pressure. fore, the 8-bit resolution mode is recommended (however, calculations will be shown with the 12-bit resolution mode). There are several different ways of performing this measurement. The TSC2000 supports two methods. The first method requires knowing the X-plate resistance, measurement of the X-position, and two additional cross panel measurements (Z2 and Z1) of the touch screen, as seen in Figure 3. Using Equation 1 will calculate the touch resistance: RTOUCH = RX-Plate * X-Position Z2 -1 4096 Z1 THE 4-WIRE TOUCH SCREEN COORDINATE PAIR MEASUREMENT (1) Measure X-Position X+ A 4-wire touch screen is constructed as shown in Figure 2. It consists of two transparent resistive layers separated by insulating spacers. Y+ Touch X-Position Conductive Bar Transparent Conductor (ITO) Top Side Y- X- Transparent Conductor (ITO) Bottom Side Y+ Measure Z1-Position Y+ X+ X+ Touch Z1-Position X- Silver Ink Y- X- Y+ X+ Y- Touch Insulating Material (Glass) Z2-Position ITO = Indium Tin Oxide X- Y- Measure Z2-Position FIGURE 2. 4-Wire Touch Screen Construction. The 4-wire touch screen panel works by applying a voltage across the vertical or horizontal resistive network. The A/D converter converts the voltage measured at the point the panel is touched. A measurement of the Y-position of the pointing device is made by connecting the X+ input to a data converter chip, turning on the Y+ and Y- drivers, and digitizing the voltage seen at the X+ input. The voltage measured is determined by the voltage divider developed at the point of touch. For this measurement, the horizontal panel resistance in the X+ lead does not affect the conversion due to the high input impedance of the A/D converter. Voltage is then applied to the other axis, and the A/D converter converts the voltage representing the X-position on the screen. This provides the X- and Y-coordinates to the associated processor. Measuring touch pressure (Z) can also be done with the TSC2000. To determine pen or finger touch, the pressure of the "touch" needs to be determined. Generally, it is not necessary to have very high performance for this test, there- FIGURE 3. Pressure Measurement. The second method requires knowing both the X-plate and Y-plate resistance, measurement of X-position and Y-position, and Z1. Using Equation 2 will also calculate the touch resistance: (2) RTOUCH = RX-Plate * When the touch panel is pressed or touched, and the drivers to the panel are turned on, the voltage across the touch panel will often overshoot and then slowly settle (decay) down to a stable DC value. This is due to mechanical bouncing which is caused by vibration of the top layer sheet of the touch panel when the panel is pressed. This settling time must be accounted for, or else the converted value will be in error. Therefore, a delay must be introduced between the time the driver for a particular measurement is turned on, and the time measurement is made. TSC2000 SBAS257 X-Position 4096 Y-Position -1 -R Y-Plate * 4096 Z1 4096 www.ti.com 9 In some applications, external capacitors may be required across the touch screen for filtering noise picked up by the touch screen; i.e., noise generated by the LCD panel or back-light circuitry. The value of these capacitors will provide a low-pass filter to reduce the noise, but will cause an additional settling time requirement when the panel is touched. Several solutions to this problem are available in the TSC2000. A programmable delay time is available which sets the delay between turning the drivers on and making a conversion. This is referred to as the Panel Voltage Stabilization time, and is used in some of the modes available in the TSC2000. In other modes, the TSC2000 can be commanded to turn on the drivers only without performing a conversion. Time can then be allowed before a conversion is started. +VDD TEMP1 The TSC2000 touch screen interface can measure position (X and Y) and pressure (Z). Determination of these coordinates is possible under three different modes of the A/D converter: conversion controlled by the TSC2000, initiated by detection of a touch; conversion controlled by the TSC2000, initiated by the host responding to the PENIRQ signal; or conversion completely controlled by the host processor. A/D CONVERTER The analog inputs of the TSC2000 are shown in Figure 4. The analog inputs (X, Y, and Z touch panel coordinates, battery voltage monitors, chip temperature, and auxiliary inputs) are provided via a multiplexer to the Successive Approximation Register (SAR) A/D converter. The A/D converter architecture is based on capacitive redistribution architecture which inherently includes a sample-and-hold function. VREF TEMP0 X+ X- Ref ON/OFF Y+ +IN Y- +REF Converter 2.5V Reference -IN -REF 7.5k VBAT1 2.5k VBAT2 2.5k 2.5k Battery On Battery On AUX1 AUX2 GND FIGURE 4. Simplified Diagram of the Analog Input Section. 10 TSC2000 www.ti.com SBAS257 A unique configuration of low on-resistance switches allows an unselected A/D converter input channel to provide power and an accompanying pin to provide ground for driving the touch panel. By maintaining a differential input to the converter and a differential reference input architecture, it is possible to negate errors caused by the driver switch onresistances. The A/D converter is controlled by an A/D Converter Control Register. Several modes of operation are possible, depending upon the bits set in the control register. Channel selection, scan operation, averaging, resolution, and conversion rate may all be programmed through this register. These modes are outlined in the sections below for each type of analog input. The results of conversions made are stored in the appropriate result register. Data Format The TSC2000 output data is in Straight Binary format, as shown in Figure 5. This figure shows the ideal output code for the given input voltage and does not include the effects of offset, gain, or noise. FS = Full-Scale Voltage = VREF(1) 1LSB = VREF(1)/4096 1LSB 11...111 Output Code 11...110 11...101 ing the conversions at lower resolutions reduces the amount of time it takes for the A/D converter to complete its conversion process, which lowers power consumption. Conversion Clock and Conversion Time The TSC2000 contains an internal 8MHz clock, which is used to drive the state machines inside the device that perform the many functions of the part. This clock is divided down to provide a clock to run the A/D converter. The division ratio for this clock is set in the A/D Converter Control Register. The ability to change the conversion clock rate allows the user to choose the optimal value for resolution, speed, and power. If the 8MHz clock is used directly, the A/D converter is limited to 8-bit resolution; using higher resolutions at this speed will not result in accurate conversions. Using a 4MHz conversion clock is suitable for 10-bit resolution; 12-bit resolution requires that the conversion clock run at 1MHz or 2MHz. Regardless of the conversion clock speed, the internal clock will run nominally at 8MHz. The conversion time of the TSC2000 is dependent upon several functions. While the conversion clock speed plays an important role in the time it takes for a conversion to complete, a certain number of internal clock cycles is needed for proper sampling of the signal. Moreover, additional times, such as the Panel Voltage Stabilization time, can add significantly to the time it takes to perform a conversion. Conversion time can vary depending upon the mode in which the TSC2000 is used. Throughout this data sheet, internal and conversion clock cycles will be used to describe the times that many functions take. In considering the total system design, these times must be taken into account by the user. Touch Detect 00...010 The pen interrupt (PENIRQ) output function is detailed in Figure 6. While in the power-down mode, the Y- driver is ON and connected to GND and the PENIRQ output is connected to the X+ input. When the panel is touched, the X+ input is 00...001 00...000 FS - 1LSB 0V Input Voltage(2) (V) NOTES: (1) Reference voltage at converter: +REF - (-REF). See Figure 4. (2) Input voltage at converter, after multiplexer: +IN - (-IN). See Figure 4. PENIRQ VDD VDD FIGURE 5. Ideal Input Voltages and Output Codes. TEMP1 TEMP2 50k Reference Y+ The TSC2000 has an internal voltage reference that can be set to 1.25V or 2.5V, through the Reference Control Register. HIGH Except when TEMP1, TEMP2 Activated TEMP DIODE X+ The internal reference voltage is only used in the singleended mode for battery monitoring, temperature measurement, and for utilizing the auxiliary inputs. Optimal touch screen performance is achieved when using a ratiometric conversion, thus all touch screen measurements are done automatically in the differential mode. An external reference can also be applied to the VREF pin, and the internal reference can be turned off. Y- ON Y+ or X+ Drivers On, or TEMP1, TEMP2 Measurements Activated. Variable Resolution The TSC2000 provides three different resolutions for the A/D converter: 8-, 10-, or 12-bits. Lower resolutions are often practical for measurements such as touch pressure. Perform- FIGURE 6. PENIRQ Functional Block Diagram. TSC2000 SBAS257 www.ti.com 11 pulled to ground through the touch screen and PENIRQ output goes LOW due to the current path through the panel to GND, initiating an interrupt to the processor. During the measurement cycles for the X- and Y-positions, the X+ input will be disconnected from the PENIRQ pull-down transistor to eliminate any leakage current from the pull-up resistor to flow through the touch screen, thus causing no errors. In modes where the TSC2000 needs to detect if the screen is still touched (for example, when doing a PENIRQ-initiated X, Y, and Z conversion), the TSC2000 must reset the drivers so that the 50k resistor is connected again. Due to the high value of this pull-up resistor, any capacitance on the touch screen inputs will cause a long delay time, and may prevent the detection from occurring correctly. To prevent this, the TSC2000 has a circuit which allows any screen capacitance to be "precharged", so that the pull-up resistor doesn't have to be the only source for the charging current. The time allowed for this precharge, as well as the time needed to sense if the screen is still touched, can be set in the Configuration Control register. This illustrates the need to use the minimum capacitor values possible on the touch screen inputs. These capacitors may be needed to reduce noise, but too large a value will increase the needed precharge and sense times, as well as panel voltage stabilization time. The idle state of the serial clock for the TSC2000 is LOW, which corresponds to a clock polarity setting of 0 (typical microprocessor SPI control bit CPOL = 0). The TSC2000 interface is designed so that with a clock phase bit setting of 1 (typical microprocessor SPI control bit CPHA = 1), the master begins driving its MOSI pin and the slave begins driving its MISO pin on the first serial clock edge. The SS pin should idle HIGH between transmissions. The TSC2000 will only interpret command words which are transmitted after the falling edge of SS. TSC2000 COMMUNICATION PROTOCOL The TSC2000 is entirely controlled by registers. Reading and writing these registers is accomplished by the use of a 16-bit command, which is sent prior to the data for that register. The command is constructed as shown in Table I. The command word begins with a R/W bit, which specifies the direction of data flow on the serial bus. The following four bits specify the page of memory this command is directed to, as shown in Table II. The next six bits specify the register address on that page of memory to which the data is directed. The last five bits are reserved for future use. PG3 PG2 PG1 PG0 PAGE ADDRESSED 0 0 0 0 0 0 0 0 1 1 0 0 1 0 Reserved 0 0 1 1 Reserved 0 1 0 0 Reserved 0 1 0 1 Reserved 0 1 1 0 Reserved 0 1 1 1 Reserved 1 0 0 0 Reserved 1 0 0 1 Reserved 1 0 1 0 Reserved 1 0 1 1 Reserved 1 1 0 0 Reserved 1 1 0 1 Reserved 1 1 1 0 Reserved 1 1 1 1 Reserved DIGITAL INTERFACE The TSC2000 communicates through a standard SPI bus. The SPI allows full-duplex, synchronous, serial communication between a host processor (the master) and peripheral devices (slaves). The SPI master generates the synchronizing clock and initiates transmissions. The SPI slave devices depend on a master to start and synchronize transmissions. A transmission begins when initiated by a master SPI. The byte from the master SPI begins shifting in on the slave MOSI pin under the control of the master serial clock. As the byte shifts in on the MOSI pin, a byte shifts out on the MISO pin to the master shift register. TABLE II. Page Addressing. MSB BIT 15 BIT 14 BIT 13 BIT 12 BIT 11 BIT 10 BIT 9 BIT 8 BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 LSB BIT 0 R/W PG3 PG2 PG1 PG0 ADDR5 ADDR4 ADDR3 ADDR2 ADDR1 ADDR0 X X X X X TABLE I. TSC2000 Command Word. 12 TSC2000 www.ti.com SBAS257 To read all the first page of memory, for example, the host processor must send the TSC2000 the command 8000H--this specifies a read operation beginning at Page 0, Address 0. The processor can then start clocking data out of the TSC2000. The TSC2000 will automatically increment its address pointer to the end of the page; if the host processor continues clocking data out past the end of a page, the TSC2000 will simply send back the value FFFFH. PAGE 0: DATA REGISTERS PAGE 1: CONTROL REGISTERS ADDR REGISTER ADDR REGISTER 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F X Y Z1 Z2 Reserved BAT1 BAT2 AUX1 AUX2 TEMP1 TEMP2 DAC Reserved Reserved Reserved Reserved ZERO Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F ADC Reserved DACCTL REF RESET CONFIG Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Likewise, writing to Page 1 of memory would consist of the processor writing the command 0800H, which would specify a write operation, with PG0 set to 1, and all the ADDR bits set to 0. This would result in the address pointer pointing at the first location in memory on Page 1. See the TSC2000 Memory Map section for details of register locations. Figure 7 shows an example of a complete data transaction between the host processor and the TSC2000. TSC2000 MEMORY MAP The TSC2000 has several 16-bit registers which allow control of the device as well as providing a location for results from the TSC2000 to be stored until read by the host microprocessor. These registers are separated into two pages of memory in the TSC2000: a Data page (Page 0) and a Control page (Page 1). The memory map is shown in Table III. TABLE III. TSC2000 Memory Map. Read Operation Write Operation SS SCLK MOSI Command Word Data Command Word MISO Data Data FIGURE 7. Write and Read Operation of TSC2000 Interface. TSC2000 SBAS257 www.ti.com 13 TSC2000 CONTROL REGISTERS the TSC2000, bits in control registers may refer to slightly different functions depending upon if you are reading the register or writing to it. A summary of all registers and bit locations is shown in Table IV. This section will describe each of the registers that were shown in the memory map of Table III. The registers are grouped according to the function they control. Note that in PAGE ADDR (HEX) REGISTER NAME D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 RESET VALUE (HEX) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F X Y Z1 Z2 Reserved BAT1 BAT2 AUX1 AUX2 TEMP1 TEMP2 DAC Reserved Reserved Reserved Reserved ZERO Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved ADC Reserved DACCTL REF RESET CONFIG Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved 0 0 0 0 0 0 0 0 0 0 0 X 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 PSM 0 DPD X 1 1 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 X 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 STS 1 0 X 0 1 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 X 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 AD3 0 0 X 1 1 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 X 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 AD2 0 0 X 1 1 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 R11 R11 R11 R11 0 R11 R11 R11 R11 R11 R11 X 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 AD1 0 0 X 1 1 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 R10 R10 R10 R10 0 R10 R10 R10 R10 R10 R10 X 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 AD0 0 0 X 0 1 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 R9 R9 R9 R9 0 R9 R9 R9 R9 R9 R9 X 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 RS1 0 0 X 1 1 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 R8 R8 R8 R8 0 R8 R8 R8 R8 R8 R8 X 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 RS0 0 0 X 1 1 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 R7 R7 R7 R7 0 R7 R7 R7 R7 R7 R7 D7 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 AV1 0 0 X X 1 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 R6 R6 R6 R6 0 R6 R6 R6 R6 R6 R6 D6 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 AV0 0 0 X X 1 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 R5 R5 R5 R5 0 R5 R5 R5 R5 R5 R5 D5 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 CL1 0 0 X X PR2 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 R4 R4 R4 R4 0 R4 R4 R4 R4 R4 R4 D4 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 CL0 0 0 INT X PR1 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 R3 R3 R3 R3 0 R3 R3 R3 R3 R3 R3 D3 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 PV2 0 0 DL1 X PR0 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 R2 R2 R2 R2 0 R2 R2 R2 R2 R2 R2 D2 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 PV1 0 0 DL0 X SN2 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 R1 R1 R1 R1 0 R1 R1 R1 R1 R1 R1 D1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 PV0 0 0 PND X SN1 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 R0 R0 R0 R0 0 R0 R0 R0 R0 R0 R0 D0 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 x 0 0 RFV X SN0 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 007F FFFF FFFF FFFF FFFF 0000 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 4000 4000 8000 0002 FFFF FFC0 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF 0000 FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF FFFF NOTE: X = Don't Care. TABLE IV. Register Summary for TSC2000. 14 TSC2000 www.ti.com SBAS257 TSC2000 A/D CONVERTER CONTROL REGISTER (PAGE 1, ADDRESS 00H) The A/D converter in the TSC2000 is shared between all the different functions. A control register determines which input is selected, as well as other options. The result of the conversion is placed in one of the result registers in Page 0 of memory, depending upon the function selected. lifted or the process is stopped. Continuous scans or conversions can be stopped by writing a 1 to this bit. This will immediately halt a conversion (even if the pen is still down) and cause the A/D converter to power down. The default state is continuous conversions, but if this bit is read after a reset or power-up, it will read 1. STS The A/D Converter Control Register controls several aspects of the A/D converter. The register is formatted as shown in Table VI. Bit 15: PSM--Pen Status/Control Mode. Reading this bit allows the host to determine if the screen is touched. Writing to this bit determines the mode used to read coordinates: host controlled, or under control of the TSC2000 responding to a screen touch. When reading, the PENSTS bit indicates if the pen is down or not. When writing to this register, this bit determines if the TSC2000 controls the reading of coordinates, or if the coordinate conversions are host-controlled. The default state is host-controlled conversions (0). Read Read Write Write VALUE 0 1 0 1 VALUE Read Read Write Write 0 1 0 1 DESCRIPTION Converter is Busy Conversions are Complete, Data is Available Normal Operation Stop Conversion and Power Down TABLE VII. STS Bit Operation. Bits [13:10]: AD3-AD0--A/D Converter Function Select Bits. These bits control which input is to be converted, and what mode the converter is placed in. These bits are the same whether reading or writing. A complete listing of how these bits are used is shown in Table VIII. Bits[9:8]: RS1, RS0--Resolution Control. The A/D converter resolution is specified with these bits. A description of these bits is shown in Table IX. These bits are the same whether reading or writing. PSM READ/WRITE READ/WRITE DESCRIPTION No Screen Touch Detected Screen Touch Detected Conversions Controlled by Host Conversions Controlled by TSC2000 TABLE V. PSM Bit Operation. Bit 14: STS--A/D Converter Status. When reading this bit indicates if the converter is busy, or if conversions are complete and data is available. Writing a 0 to this bit will cause touch screen scans to continue until either the pen is RS1 RS0 FUNCTION 0 0 12-Bit Resolution. Power up and reset default. 0 1 8-Bit Resolution 1 0 10-Bit Resolution 1 1 12-Bit Resolution TABLE IX. A/D Converter Resolution Control. MSB BIT 15 BIT 14 BIT 13 BIT 12 BIT 11 BIT 10 BIT 9 BIT 8 BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 LSB BIT 0 PSM STS AD3 AD2 AD1 AD0 RS1 RS0 AV1 AV0 CL1 CL0 PV2 PV1 PV0 X TABLE VI. A/D Converter Control Register. A/D3 A/D2 A/D1 A/D0 0 0 0 0 0 0 0 1 0 0 1 0 0 0 0 0 0 1 1 1 1 0 1 1 1 1 0 0 0 0 1 0 0 1 1 0 0 1 1 1 0 1 0 1 0 1 0 1 1 1 0 0 1 1 1 1 1 1 0 1 1 1 0 1 FUNCTION Invalid. No registers will be updated. This is the default state after a reset. Touch screen scan function: X and Y coordinates converted and the results returned to X and Y data registers. Scan continues until either the pen is lifted or a stop bit is sent. Touch screen scan function: X, Y, Z1, and Z2 coordinates converted and the results returned to X, Y, Z1, and Z2 data registers. Scan continues until either the pen is lifted or a stop bit is sent. Touch screen scan function: X coordinate converted and the results returned to X data register. Touch screen scan function: Y coordinate converted and the results returned to Y data register. Touch screen scan function: Z1 and Z2 coordinates converted and the results returned to Z1 and Z2 data registers. Battery Input 1 converted and the results returned to the BAT1 data register. Battery Input 2 converted and the results returned to the BAT2 data register. Auxiliary Input 1 converted and the results returned to the AUX1 data register. Auxiliary Input 2 converted and the results returned to the AUX2 data register. A temperature measurement is made and the results returned to the temperature measurement 1 data register. Port scan function: Battery Input 1, Battery Input 2, Auxiliary Input 1, and a Auxiliary Input measurements are made and the results returned to the appropriate data registers. A differential temperature measurement is made and the results returned to the temperature measurement 2 data register. Turn on X+, X- drivers. Turn on Y+, Y- drivers. Turn on Y+, X- drivers. TABLE VIII. A/D Converter Function Select. TSC2000 SBAS257 www.ti.com 15 Bits[7:6]: AV1, AV0 = Converter Averaging Control. These two bits allow you to specify the number of averages the converter will perform, as shown in Table X. Note that when averaging is used, the STS bit and the DAV output will indicate that the converter is busy until all conversions necessary for the averaging are complete. The default state for these bits is 00, selecting no averaging. These bits are the same whether reading or writing. AV1 AV0 0 0 1 1 0 1 0 1 D/A CONVERTER CONTROL REGISTER (PAGE 1, ADDRESS 02H) The single bit in this register controls the power down control of the on-board D/A converter. This register is formatted as shown in Table XIII. Bit 15: DPD = D/A Converter Power Down. This bit controls whether the D/A converter is powered up and operational, or powered down. If the D/A converter is powered down, the AOUT pin will neither sink nor source current. FUNCTION None 4 Data Averages 8 Data Averages 16 Data Averages DPD VALUE 0 1 TABLE X. A/D Conversion Averaging Control. DESCRIPTION D/A Converter is Powered and Operational D/A Converter is Powered Down TABLE XIV. DPD Bit Operation. Bits[5:4]: CL1, CL0 = Conversion Clock Control. These two bits specify the internal clock rate which the A/D converter uses when performing a single conversion, as shown in Table XI. These bits are the same whether reading or writing. CL1 CL0 0 0 1 1 0 1 0 1 FUNCTION 8MHz Internal Clock Rate--8-Bit Resolution Only 4MHz Internal Clock Rate--10-Bit Resolution Only 2MHz Internal Clock Rate. 1MHz Internal Clock Rate. TABLE XI. A/D Converter Clock Control. Bits [3:1]: PV2 - PV0 = Panel Voltage Stabilization Time control. These bits allow you to specify a delay time from the time a pen touch is detected to the time a conversion is started. This allows you to select the appropriate settling time for the touch panel used. Table XII shows the settings of these bits. The default state is 000, indicating a 0ms stabilization time. These bits are the same whether reading or writing. Bit 0: This bit is not used, and is a "don't care" when writing. It will always read as a zero. PV2 PV1 PV0 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 FUNCTION 0s Stabilization Time 100s Stabilization Time 500s Stabilization Time 1ms Stabilization Time 5ms Stabilization Time 10ms Stabilization Time 50ms Stabilization Time 100ms Stabilization Time REFERENCE REGISTER (PAGE 1, ADDRESS 03H) The TSC2000 has a register to control the operation of the internal reference. This register is formatted as shown in Table XV. Bit 4: INT = Internal Reference Mode. If this bit is written to a 1, the TSC2000 will use its internal reference; if this bit is a zero, the part will assume an external reference is being supplied. The default state for this bit is to select an external reference (0). This bit is the same whether reading or writing. INT VALUE 0 1 DESCRIPTION External Reference Selected Internal Reference Selected TABLE XVI. INT Bit Operation. Bits [3:2]: DL1, DL0 = Reference Power-Up Delay. When the internal reference is powered up, a finite amount of time is required for the reference to settle. If measurements are made before the reference has settled, these measurements will be in error. These bits allow for a delay time for measurements to be made after the reference powers up, thereby assuring that the reference has settled. Longer delays will be necessary depending upon the capacitance present at the REF pin (see Typical Characteristics). See Table XVII for the delays. The default state for these bits is 00, selecting a 0ms delay. These bits are the same whether reading or writing. TABLE XII. Panel Voltage Stabilization Time Control. MSB BIT 15 BIT 14 BIT 13 BIT 12 BIT 11 BIT 10 BIT 9 BIT 8 BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 LSB BIT 0 DPD X X X X X X X X X X X X X X X TABLE XIII. D/A Converter Control Register. MSB BIT 15 BIT 14 BIT 13 BIT 12 BIT 11 BIT 10 BIT 9 BIT 8 BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 LSB BIT 0 X X X X X X X X X X X INT DL1 DL0 PDN RFV TABLE XV. Reference Register. 16 TSC2000 www.ti.com SBAS257 DL1 DL0 0 0 1 1 0 1 0 1 TSC2000 CONFIGURATION CONTROL REGISTER (PAGE 1, ADDRESS 05H) DELAY TIME 0s 100s 500s 1000s This control register controls the configuration of the precharge and sense times for the touch detect circuit. The register is formatted as shown in Table XXI. TABLE XVII. Reference Power-Up Delay Settings. Bit 1: PDN = Reference Power Down. If a 1 is written to this bit, the internal reference will be powered down between conversions. If this bit is a zero, the internal reference will be powered at all times. The default state is to power down the internal reference, so this bit will be a 1. This bit is the same whether reading or writing. Bits [5:3]: PRE[2:0] = Precharge Time Selection Bits. These bits set the amount of time allowed for precharging any pin capacitance on the touch screen prior to sensing if a screen touch is happening. PRE[2:0] PRE2 PRE1 PRE0 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 PDN VALUE DESCRIPTION 0 1 Internal Reference is Powered at All Times Internal Reference is Powered Down Between Conversions TABLE XVIII. PDN Bit Operation. TIME 20s 84s 276s 340s 1.044ms 1.108ms 1.300ms 1.364ms TABLE XXII. Precharge Times. Note that the PDN bit, in concert with the INT bit, creates a few possibilities for reference behavior. These are detailed in Table XIX. INT PDN REFERENCE BEHAVIOR 0 0 External Reference Used, Internal Reference Powered Down 0 1 External Reference Used, Interenal Reference Powered Down 1 1 0 1 Internal Reference Used, Always Powered Up Internal Reference Used, Will Power Up During Conversions Bits [2:0]: SNS[2:0] = Sense Time Selection Bits. These bits set the amount of time the TSC2000 will wait to sense a screen touch between coordinate axis conversions in PENIRQ-controlled mode. SNS[2:0] SNS2 SNS1 SNS0 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 and Then Power Down TABLE XIX. Reference Behavior Possibilities. Bit 0: RFV = Reference Voltage control. This bit selects the internal reference voltage, either 1.25V or 2.5V. The default value is 1.25V. This bit is the same whether reading or writing. TIME 32s 96s 544s 608s 2.080ms 2.144ms 2.592ms 2.656ms TABLE XXIII. Sense Times. RFV VALUE DESCRIPTION 0 1 1.25V Reference Voltage 2.5V Reference Voltage TABLE XX. RFV Bit Operation. MSB BIT 15 BIT 14 BIT 13 BIT 12 BIT 11 BIT 10 BIT 9 BIT 8 BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 LSB BIT 0 X X X X X X X X X X PRE2 PRE1 PRE0 SNS2 SNS1 SNS0 TABLE XXI. Configuration Control Register. TSC2000 SBAS257 www.ti.com 17 RESET REGISTER (PAGE 1, ADDRESS 04H) ZERO REGISTER (PAGE 0, ADDRESS 10H) The TSC2000 has a special register, the RESET register, which allows a software reset of the device. Writing the code BBXXH, as shown in Table XXIV, to this register will cause the TSC2000 to reset all its registers to their default, power-up values. This is a reserved data register, but instead of reading all 1's (FFFFH), when read will return all 0's (0000H). Writing any other values to this register will do nothing. Reading this register or any reserved register will result in reading back all 1's, or FFFFH. As noted previously in the discussion of the A/D converter, several operating modes can be used, which allow great flexibility for the host processor. These different modes will now be examined. TSC2000 DATA REGISTERS Conversion Controlled by TSC2000 Initiated at Touch Detect The data registers of the TSC2000 hold data results from conversions or keypad scans, or the value of the D/A converter output current. All of these registers default to 0000H upon reset, except the D/A converter register, which is set to 0080H, representing the midscale output of the D/A converter. X, Y, Z1, Z2, BAT1, BAT2, AUX1, AUX2, TEMP1, AND TEMP2 REGISTERS The results of all A/D conversions are placed in the appropriate data register, see Tables III and VIII. The data format of the result word, R, of these registers is right-justified, as shown in Table XXV. D/A CONVERTER DATA REGISTER (PAGE 0, ADDRESS 0BH) The data to be written to the D/A converter is written into the D/A converter data register, which is formatted as shown in Table XXVI. OPERATION--TOUCH SCREEN MEASUREMENTS In this mode, the TSC2000 will detect when the touch panel is touched and cause the PENIRQ line to go LOW. At the same time, the TSC2000 will start up its internal clock. It will then turn on the Y-drivers, and after a programmed Panel Voltage Stabilization time, power up the A/D converter and convert the Y-coordinate. If averaging is selected, several conversions may take place; when data averaging is complete, the Ycoordinate result will be stored in the Y-register. If the screen is still touched at this time, the X-drivers will be enabled, and the process will repeat, but instead measuring the X-coordinate and storing the result in the X-register. If only X- and Y-coordinates are to be measured, then the conversion process is complete. See Figure 8 for a flowchart for this process. The time it takes to go through this process depends upon the selected resolution, internal conversion clock rate, averaging selected, panel voltage stabilization time, and precharge and sense times. MSB BIT 15 BIT 14 BIT 13 BIT 12 BIT 11 BIT 10 BIT 9 BIT 8 BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 LSB BIT 0 1 0 1 1 1 0 1 1 X X X X X X X X LSB BIT 0 TABLE XXIV. Reset Register. MSB BIT 15 BIT 14 BIT 13 BIT 12 BIT 11 BIT 10 BIT 9 BIT 8 BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 0 0 0 0 R11 MSB R10 R9 R8 R7 R6 R5 R4 R3 R2 R1 R0 LSB TABLE XXV. Result Data Format. MSB BIT 15 BIT 14 BIT 13 BIT 12 BIT 11 BIT 10 BIT 9 BIT 8 BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 LSB BIT 0 X X X X X X X X D7 D6 D5 D4 D3 D2 D1 D0 TABLE XXVI. D/A Converter Register. 18 TSC2000 www.ti.com SBAS257 The time needed to get a complete X/Y-coordinate reading can be calculated by: (3) 1 tCOORDINATE = 2.5 s + 2( tPVS + tPRE + tSNS ) + 2NAVG NBITS * + 4.4s fCONV where, tCOORDINATE = time to complete X/Y-coordinate reading tPVS = Panel Voltage Stabilization time, see Table XII tPRE = precharge time, see Table XXII NBITS = number of bits of resolution, see Table IX fCONV = A/D converter clock frequency, see Table XI If the pressure of the touch is also to be measured, the process will continue in the same way, but measuring the Z1 and Z2 values, and placing them in the Z1 and Z2 registers, see Figure 9. As before, this process time depends upon the settings described above. The time for a complete X, Y, Z1, and Z2 coordinate reading is given by: (4) 1 tCOORDINATE = 4.75s + 3( tPVS + tPRE + tSNS ) + 4NAVG NBITS * + 4.4s fCONV tSNS = sense time, see Table XXIII NAVG = number of averages, see Table X; for no averaging, NAVG = 1 Touch Screen Scan X and Y PENIRQ Initiated Screen Touch Turn On Drivers: X+, X- Issue Interrupt PENIRQ No No Is PSM = 1 Go to Host-Controlled Conversion Is Panel Voltage Stabilization Done Yes Power Up A/D Converter Yes Start Clock Convert X-Coordinates Turn On Drivers: Y+, Y- No No Is Panel Voltage Stabilization Done Yes Is Data Averaging Done Yes Store X-Coordinates in X-Register Power Up A/D Converter Convert Y-Coordinates Power Down A/D Converter No Issue Data Available Is Data Averaging Done Yes Yes Store Y-Coordinates in Y-Register Is Screen Touched No Power Down A/D Converter Is Screen Touched No Turn Off Clock Turn Off Clock Reset PENIRQ and Scan Trigger Reset PENIRQ and Scan Trigger Done Done Yes FIGURE 8. X- and Y-Coordinate Touch Screen Scan, Initiated by Touch. TSC2000 SBAS257 www.ti.com 19 Turn On Drivers: Y+, X- Touch Screen Scan X, Y, and Z PENIRQ Initiated No Screen Touch Is Panel Voltage Stabilization Done Yes Turn On Drivers: X+, X- Issue Interrupt PENIRQ Power Up A/D Converter No Is PSM = 1 No Go to Host-Controlled Conversion Is Panel Voltage Stabilization Done Convert Z1-Coordinates Yes Yes No Start Clock Power Up A/D Converter Turn On Drivers: Y+, Y- Convert X-Coordinates Is Data Averaging Done Yes Store Z1-Coordinates in Z1-Register No Is Panel Voltage Stabilization Done No Is Data Averaging Done Convert Z2-Coordinates Yes Yes Power Up A/D Converter No Store X-Coordinates in X-Register Convert Y-Coordinates Is Data Averaging Done Yes Power Down A/D Converter Turn Off Clock Store Z2-Coordinates in Z2-Register No Is Data Averaging Done Is Screen Touched Reset PENIRQ and Scan Trigger Power Down A/D Converter Yes Done Store Y-Coordinates in Y-Register Issue Data Available Power Down A/D Converter Is Screen Touched Turn Off Clock No Yes Reset PENIRQ and Scan Trigger Is Screen Touched No Turn Off Clock Done Yes Reset PENIRQ and Scan Trigger Done FIGURE 9. X-, Y-, and Z-Coordinate Touch Screen Scan, Initiated by Touch. 20 TSC2000 www.ti.com SBAS257 Conversion Controlled by TSC2000 Initiated By Host Responding to PENIRQ scan functions. The conversion process then proceeds as described above, and as outlined in Figures 10 through 14. In this mode, the TSC2000 will detect when the touch panel is touched and cause the PENIRQ line to go LOW. The host will recognize the interrupt request, and then write to the A/D Converter Control register to select one of the touch screen The main difference between this mode and the previous mode is that the host, not the TSC2000, decides when the touch screen scan begins. Screen Touch Touch Screen Scan X and Y Host Initiated Issue Interrupt PENIRQ No Is PSM = 1 Go to Host-Controlled Conversion Done Host Writes A/D Converter Control Register Turn On Drivers: X+, X- Reset PENIRQ No Is Panel Voltage Stabilization Done Start Clock Yes Power Up A/D Converter Turn On Drivers: Y+, Y- Convert X-Coordinates No Is Panel Voltage Stabilization Done Yes No Is Data Averaging Done Power Up A/D Converter Yes Convert Y-Coordinates Store X-Coordinates in X-Register No Is Data Averaging Done Power Down A/D Converter Yes Issue Data Available Store Y-Coordinates in Y-Register Yes Power Down A/D Converter Is Screen Touched Turn Off Clock No Is Screen Touched No Reset PENIRQ and Scan Trigger Turn Off Clock Done Done Yes FIGURE 10. X- and Y-Coordinate Touch Screen Scan, Initiated by Host. TSC2000 SBAS257 www.ti.com 21 Screen Touch Touch Screen Scan X, Y, and Z Host Initiated Issue Interrupt PENIRQ Turn On Drivers: Y+, X- No No Is PSM = 1 Go to Host-Controlled Conversion Turn On Drivers: X+, X- Is Panel Voltage Stabilization Done Yes Power Up A/D Converter Done No Host Writes A/D Converter Control Register Is Panel Voltage Stabilization Done Convert Z1-Coordinates Yes Reset PENIRQ Power Up A/D Converter No Is Data Averaging Done Start Clock Convert X-Coordinates Yes Store Z1-Coordinates in Z1-Register Turn On Drivers: Y+, Y- No No Is Data Averaging Done Convert Z2-Coordinates Is Panel Voltage Stabilization Done Yes Store X-Coordinates in X-Register Yes No Is Data Averaging Done Power Up A/D Converter Power Down A/D Converter Yes Turn Off Clock Convert Y-Coordinates Store Z2-Coordinates in Z2-Register Is Screen Touched No No Reset PENIRQ and Scan Trigger Is Data Averaging Done Power Down A/D Converter Yes Done Yes Issue Data Available Store Y-Coordinates in Y-Register Yes Power Down A/D Converter Is Screen Touched Turn Off Clock No Is Screen Touched No Turn Off Clock Reset PENIRQ and Scan Trigger Done Done Yes FIGURE 11. X-, Y-, and Z-Coordinate Touch Screen Scan, Initiated by Host. 22 TSC2000 www.ti.com SBAS257 Screen Touch Touch Screen Scan X-Coordinate Host Initiated Issue Interrupt PENIRQ No Is PSM = 1 Go to Host-Controlled Conversion Convert X-Coordinates Done No Host Writes A/D Converter Control Register Is Data Averaging Done Yes Reset PENIRQ Store X-Coordinates in X-Register No Start Clock Are Drivers On Yes Turn On Drivers: X+, X- Power Down A/D Converter Issue Data Available Turn Off Clock Start Clock No Is Panel Voltage Stabilization Done Done Yes Power Up A/D Converter FIGURE 12. X-Coordinate Reading Initiated by Host. TSC2000 SBAS257 www.ti.com 23 Screen Touch Touch Screen Scan Y-Coordinate Host Initiated Issue Interrupt PENIRQ No Is PSM = 1 Go to Host-Controlled Conversion Store Y-Coordinates in Y-Register Done Power Down A/D Converter Host Writes A/D Converter Control Register Issue Data Available Reset PENIRQ Turn Off Clock Are Drivers On Done No Start Clock Yes Turn On Drivers: Y+, Y- Start Clock No Power Up A/D Converter Is Panel Voltage Stabilization Done Yes Convert Y-Coordinates No Is Data Averaging Done Yes FIGURE 13. Y-Coordinate Reading Initiated by Host. 24 TSC2000 www.ti.com SBAS257 Screen Touch Touch Screen Scan Z-Coordinate Host Initiated Issue Interrupt PENIRQ No Is PSM = 1 Go to Host-Controlled Conversion Convert Z2-Coordinates Done Host Writes A/D Converter Control Register No Reset PENIRQ Are Drivers On Is Data Averaging Done Yes Store Z2-Coordinates in Z2-Register No Start Clock Power Down A/D Converter Turn On Drivers: Y+, X- Yes Issue Data Available Start Clock No Is Panel Voltage Stabilization Done Yes Power Up A/D Converter Turn Off Clock Done Convert Z1-Coordinates No Is Data Averaging Done Yes Store Z1-Coordinates in Z1-Register FIGURE 14. Z-Coordinate Reading Initiated by Host. TSC2000 SBAS257 www.ti.com 25 Conversion Controlled by the Host In this mode, the TSC2000 will detect when the touch panel is touched and cause the PENIRQ line to go LOW. The host will recognize the interrupt request. Instead of starting a sequence in the TSC2000 which then reads each coordinate in turn, the host now must control all aspects of the conversion. Generally, upon receiving the interrupt request, the host will turn on the Y-drivers. After waiting for the settling time, the host will then address the TSC2000 again, this time requesting an X-coordinate conversion. The process is then repeated for Y- and Z-coordinates. The processes are outlined in Figures 15 through 17. The time needed to convert any single coordinate under host control (not including the time needed to send the command over the SPI bus) is given by: (5) 1 tCOORDINATE = 2.125s + tPVS + NAVG NBITS * + 4.4s fCONV Host-Controlled X-Coordinate Screen Touch Host Writes A/D ConverterControl Register Issue Interrupt PENIRQ No Start Clock No Is PSM = 1 Go to Host-Controlled Conversion Are Drivers On Yes Turn On Drivers: X+, X- Start Clock Done Host Writes A/D Converter Control Register Is Panel Voltage Stabilization Done Yes Power Up A/D Converter Convert X-Coordinates No Reset PENIRQ Turn On Drivers: X+, X- No Done Is Data Averaging Done Yes Store X-Coordinates in X-Register Power Down A/D Converter Issue Data Available Turn Off Clock Done FIGURE 15. X-Coordinate Reading Controlled by Host. 26 TSC2000 www.ti.com SBAS257 Host-Controlled Y-Coordinate Screen Touch Host Writes A/D Converter Control Register Issue Interrupt PENIRQ No Start Clock No Is PSM = 1 Go to Host-Controlled Conversion Are Drivers On Yes Turn On Drivers: Y+, Y- Start Clock Done Host Writes A/D Converter Control Register Is Panel Voltage Stabilization Done Yes Power Up A/D Converter Convert Y-Coordinate No Reset PENIRQ Turn On Drivers: Y+, Y- No Done Is Data Averaging Done Yes Store Y-Coordinates in Y-Register Power Down A/D Converter Issue Data Available Turn Off Clock Done FIGURE 16. Y-Coordinate Reading Controlled by Host. TSC2000 SBAS257 www.ti.com 27 Screen Touch Host-Controlled Z-Coordinate Issue Interrupt PENIRQ No Is PSM = 1 Convert Z2-Coordinates Go to Host-Controlled Conversion Done No Host Writes A/D Converter Control Register Is Data Averaging Done Yes Reset PENIRQ Store Z2-Coordinates in Z2-Register Turn On Drivers: Y+, X- Power Down A/D Converter Done Issue Data Available Host Writes A/D Converter Control Register Turn Off Clock Reset PENIRQ Done Is Data Averaging Done No Start Clock Turn On Drivers: Y+, X- Yes Start Clock No Is Panel Voltage Stabilization Done Yes Power Up A/D Converter Convert Z1-Coordinates No Is Data Averaging Done Yes Store Z1-Coordinates in Z1-Register FIGURE 17. Z-Coordinate Reading Controlled by Host. 28 TSC2000 www.ti.com SBAS257 OPERATION--TEMPERATURE MEASUREMENT In some applications, such as battery recharging, a measurement of ambient temperature is required. The temperature measurement technique used in the TSC2000 relies on the characteristics of a semiconductor junction operating at a fixed current level. The forward diode voltage (VBE) has a well-defined characteristic versus temperature. The ambient temperature can be predicted in applications by knowing the 25C value of the VBE voltage and then monitoring the delta of that voltage as the temperature changes. The TSC2000 offers two modes of temperature measurement. The first mode requires calibration at a known temperature, but only requires a single reading to predict the ambient temperature. A diode, as shown in Figure 18, is used during this measurement cycle. This voltage is typically 600mV at +25C with a 20A current through it. The absolute value of this diode voltage can vary a few millivolts; the temperature coefficient (TC) of this voltage is very consistent at -2.1mV/C. During the final test of the end product, the diode voltage would be stored at a known room temperature, in system memory, for calibration purposes by the user. The result is an equivalent temperature measurement resolution of 0.3C/LSB. This measurement of what is referred to as Temperature 1 is illustrated in Figure 19. Host Writes A/D Converter Control Register Temperature Input 1 Start Clock Power Up Reference Power Up A/D Converter Convert Temperature Input 1 No Is Data Averaging Done Yes Store Temperature Input 1 in TEMP1 Register Power Down A/D Converter Power Down Reference Issue Data Available Turn Off Clock Done FIGURE 19. Single Temperature Measurement Mode. X+ MUX A/D Converter Host Writes A/D Converter Control Register Temperature Input 2 Start Clock Temperature Select TEMP1 TEMP2 Power Up Reference FIGURE 18. Functional Block Diagram of Temperature Measurement Mode. Power Up A/D Converter The second mode does not require a test temperature calibration, but uses a two-measurement (differential) method to eliminate the need for absolute temperature calibration and for achieving 2C/LSB accuracy. This mode requires a second conversion with a 91 times larger current. The voltage difference between the first (TEMP1) and second (TEMP2) conversion, using 91 times the bias current, will be represented by kT/q *ln (N), where N is the current ratio = 91, k = Boltzmann's constant (1.38054 * 10-23 electrons volts/degrees Kelvin), q = the electron charge (1.602189 * 10-19 C), and T = the temperature in degrees Kelvin. This method can provide much improved absolute temperature measurement, but less resolution of 2C/LSB. The resultant equation for solving for K is: K = where, q * V k * ln(N) V = V(I91) - V(I1) (6) Convert Temperature Input 2 No Is Data Averaging Done Yes Store Temperature Input 2 in TEMP2 Register Power Down A/D Converter Power Down Reference Issue Data Available Turn Off Clock Done FIGURE 20. Additional Temperature Measurement for Differential Temperature Reading. (in mV) K = 2.573VK/mV C = 2.573 * V(mV) - 273K See Figure 20 for the Temperature 2 measurement. TSC2000 SBAS257 www.ti.com 29 OPERATION--BATTERY MEASUREMENT Host Writes A/D Converter Control Register An added feature of the TSC2000 is the ability to monitor the battery voltage on the other side of a voltage regulator (DC/ DC converter), as shown in Figure 21. The VBAT1 input is divided down by 4 so that an input range of 0.5V to 6.0V can be measured. Because of the division by 4, this input range would be represented as 0.125V to 1.5V to the A/D converter. Battery Input 1 Start Clock Power Up Reference Power Up A/D Converter Power Down A/D Converter 2.7V DC/DC Converter Battery 0.5V + to 6.0V Convert Battery Input 1 Power Down Reference VDD No Issue Data Available Is Data Averaging Done Turn Off Clock Yes 0.125V to 1.5V VBAT1 Store Battery Input 1 in BAT1 Register 7.5k Done 2.5k FIGURE 22. VBAT1 Measurement Process. Host Writes A/D Converter Control Register FIGURE 21. Battery Measurement Functional Block Diagram. Battery Input 2 The VBAT2 input is divided down by 2, so it accommodates an input range of 0.5V to 3.0V, which is represented to the A/D converter as 0.25V to 1.5V. This smaller divider ratio allows for increased resolution. Note that the VBAT2 input pin can withstand up to 6V, but this input will only provide accurate measurements within the 0.5V to 3.0V range. Start Clock Power Up Reference Power Up A/D Converter For both battery inputs, the dividers are ON only during the sampling of the battery input, in order to minimize power consumption. Convert Battery Input 2 Flowcharts which detail the process of making a battery input reading are shown in Figures 22 and 23. The time needed to make temperature, auxiliary, or battery measurements is given by: (7) tREADING = 2.625s + tREF No 1 + NAVG NBITS * + 4.4s f CONV Power Down A/D Converter Power Down Reference Is Data Averaging Done Yes Store Battery Input 2 in BAT2 Register where tREF is the reference delay time as given in Table XVII. Issue Data Available Turn Off Clock Done FIGURE 23. VBAT2 Measurement Process. 30 TSC2000 www.ti.com SBAS257 OPERATION--AUXILIARY MEASUREMENT OPERATION--PORT SCAN The two auxiliary voltage inputs can be measured in much the same way as the battery inputs, as shown in Figures 24 and 25. Applications might include external temperature sensing, ambient light monitoring for controlling the backlight, or sensing the current drawn from the battery. If making measurements of all the analog inputs (except the touch screen) is desired on a periodic basis, the Port Scan mode can be used. This mode causes the TSC2000 to sample and convert both battery inputs and both auxiliary inputs. At the end of this cycle, the battery and auxiliary result registers will contain the latest values. Thus, with one write to the TSC2000, the host can cause four different measurements to be made. Host Writes A/D Converter Control Register The flowchart for this process is shown in Figure 26. The time needed to make a complete port scan is given by: Auxiliary Input 1 Start Clock tREADING = 7.5s + tREF + 4NAVG NBITS Power Up Reference * 1 fCONV + 4.4s (8) Power Up A/D Converter Port Scan Power Down A/D Converter Convert Auxiliary Input 1 Power Down Reference No Is Data Averaging Done Convert Auxiliary Input 1 Host Writes A/D Converter Control Register Issue Data Available Start Clock No Turn Off Clock Yes Is Data Averaging Done Power Up Reference Store Auxiliary Input 1 in AUX1 Register Yes Done Power Up A/D Converter Store Auxiliary Input 1 in AUX1 Register Convert Battery Input 1 FIGURE 24. AUX1 Measurement Process. Host Writes A/D Converter Control Register No Is Data Averaging Done Auxiliary Input 2 Convert Auxiliary Input 2 No Is Data Averaging Done Yes Start Clock Yes Power Up Reference Store Battery Input 1 in BAT1 Register Power Up A/D Converter Convert Battery Input 2 Power Down A/D Converter Convert Auxiliary Input 2 No Power Down Reference Is Data Averaging Done Store Auxiliary Input 2 in AUX2 Register Power Down A/D Converter Power Down Reference Issue Data Available No Is Data Averaging Done Yes Store Auxiliary Input 2 in AUX2 Register FIGURE 25. AUX2 Measurement Process. Issue Data Available Yes Store Battery Input 2 in BAT2 Register Turn Off Clock Done Done FIGURE 26. Port Scan Mode. TSC2000 SBAS257 Turn Off Clock www.ti.com 31 OPERATION--D/A CONVERTER The TSC2000 has an on-board 8-bit D/A converter, configured as shown in Figure 27. This configuration yields a current sink (AOUT) controlled by the value of a resistor connected between the ARNG pin and ground. The D/A converter has a control register, which controls whether or not the converter is powered up. The 8-bit data is written to the D/A converter through the D/A converter data register. 0.9 IOUT (Full-Scale) (mA) 0.8 V+ 0.7 0.6 0.5 0.4 0.3 0.2 0.1 R1 0 10k VBIAS 1M 10M 100M ARNG Resistor () R2 FIGURE 28. D/A Converter Output Current Range versus RRNG Resistor Value. AOUT 8 Bits 100k D/A Converter For example, consider an LCD that has a contrast control voltage VBIAS that can range from 2V to 4V, that draws 400A when used, and an available +5V supply. Note that this is higher than the TSC2000 supply voltage, but it is within the absolute maximum ratings. ARNG RRNG The maximum VBIAS voltage is 4V, and this occurs when the D/A converter current is 0, so only the 400A load current ILOAD will be flowing from 5V to VBIAS. This means 1V will be dropped across R1, so R1 = 1V/400A = 2.5k. FIGURE 27. D/A Converter Configuration. This circuit is designed for flexibility in the output voltage at the VBIAS point shown in Figure 27 to accommodate the widely varying requirements for LCD contrast control bias. V+ can be a higher voltage than the supply voltage for the TSC2000. The only restriction is that the voltage on the AOUT pin can never go above the absolute maximum ratings for the device, and should stay above 1.5V for linear operation. The minimum VBIAS is 2V, which occurs when the D/A converter current is at its full scale value, IMAX. In this case, 5V - 2V = 3V will be dropped across R1, so the current through R1 will be 3V/2.5K = 1.2mA. This current is IMAX + ILOAD = IMAX + 400uA, so IMAX must be set to 800A. Looking at Figure 28, this means that RRNG should be around 1M. The D/A converter has an output sink range which is limited to 1mA. This range can be adjusted by changing the value of RRNG shown in Figure 27. As this D/A converter is not designed to be a precision device, the actual output current range can vary as much as 20%. Furthermore, the current output will change due to variations in temperature; the D/A converter has a temperature coefficient of approximately -2A/C. To set the full-scale current, RRNG can be determined from the graph shown in Figure 28. Since the voltage at the AOUT pin should not go below 1.5V, this limits the voltage at the bottom of R2 to be 1.5V minimum; this occurs when the D/A converter is providing its maximum current, IMAX. In this case, IMAX +ILOAD flows through R1, and IMAX flows through R2. Thus, 32 R2IMAX + R1(IMAX + ILOAD) = 5V - 1.5V = 3.5V We already have found R1 = 2.5k, IMAX = 800A, ILOAD = 400A, so we can solve this for R2 and find that it should be 625. TSC2000 www.ti.com SBAS257 In the previous example, when the D/A converter current is zero, the voltage on the AOUT pin will rise above the TSC2000 supply voltage. This is not a problem, however, since V+ was within the absolute maximum ratings of the TSC2000, so no special precautions are necessary. Many LCD displays require voltages much higher than the absolute maximum ratings of the TSC2000. In this case, the addition of an NPN transistor, as shown in Figure 29, will protect the AOUT pin from damage. V+ R1 VBIAS R2 VSUPPLY With this in mind, power to the TSC2000 should be clean and well bypassed. A 0.1F ceramic bypass capacitor should be placed as close to the device as possible. A 1F to 10F capacitor may also be needed if the impedance of the connection between +VDD and the power supply is HIGH. A bypass capacitor is generally not needed on the reference pin because the reference is buffered by an internal op amp. If an external reference voltage originates from an op amp, make sure that it can drive any bypass capacitor that is used without oscillation. The TSC2000 architecture offers no inherent rejection of noise or voltage variation in regards to using an external reference input. This is of particular concern when the reference input is tied to the power supply. Any noise and ripple from the supply will appear directly in the digital results. While high frequency noise can be filtered out, voltage variation due to line frequency (50Hz or 60Hz) can be difficult to remove. AOUT 8 Bits result. Such glitches might originate from switching power supplies, nearby digital logic, and high power devices. The degree of error in the digital output depends on the reference voltage, layout, and the exact timing of the external event. The error can change if the external event changes in time with respect to the SCL input. D/A Converter ARNG RRNG FIGURE 29. D/A Converter Circuit when Using V+ Higher than VSUPPLY. LAYOUT The following layout suggestions should provide optimum performance from the TSC2000. However, many portable applications have conflicting requirements concerning power, cost, size, and weight. In general, most portable devices have fairly "clean" power and grounds because most of the internal components are very low power. This situation would mean less bypassing for the converter's power and less concern regarding grounding. Still, each situation is unique and the following suggestions should be reviewed carefully. For optimum performance, care should be taken with the physical layout of the TSC2000 circuitry. The basic SAR architecture is sensitive to glitches or sudden changes on the power supply, reference, ground connections, and digital inputs that occur just prior to latching the output of the analog comparator. Therefore, during any single conversion for an `n-bit' SAR converter, there are n `windows' in which large external transient voltages can easily affect the conversion The GND pin should be connected to a clean ground point. In many cases, this will be the "analog" ground. Avoid connections which are too near the grounding point of a microcontroller or digital signal processor. If needed, run a ground trace directly from the converter to the power supply entry or battery connection point. The ideal layout will include an analog ground plane dedicated to the converter and associated analog circuitry. In the specific case of use with a resistive touch screen, care should be taken with the connection between the converter and the touch screen. Since resistive touch screens have fairly low resistance, the interconnection should be as short and robust as possible. Loose connections can be a source of error when the contact resistance changes with flexing or vibrations. As indicated previously, noise can be a major source of error in touch screen applications (e.g., applications that require a back-lit LCD panel). This EMI noise can be coupled through the LCD panel to the touch screen and cause "flickering" of the converted data. Several things can be done to reduce this error, such as utilizing a touch screen with a bottom-side metal layer connected to ground. This will couple the majority of noise to ground. Additionally, filtering capacitors, from Y+, Y-, X+, and X- to ground, can also help. Note, however, that the use of these capacitors will increase screen settling time and require longer panel voltage stabilization times, as well as increased precharge and sense times for the PENIRQ circuitry of the TSC2000. TSC2000 SBAS257 www.ti.com 33 PACKAGE OPTION ADDENDUM www.ti.com 21-May-2010 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp TSC2000IPW ACTIVE TSSOP PW 20 70 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TSC2000IPWG4 ACTIVE TSSOP PW 20 70 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TSC2000IPWR ACTIVE TSSOP PW 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TSC2000IPWRG4 ACTIVE TSSOP PW 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM (3) Samples (Requires Login) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device TSC2000IPWR Package Package Pins Type Drawing TSSOP PW 20 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 2000 330.0 16.4 Pack Materials-Page 1 6.95 B0 (mm) K0 (mm) P1 (mm) 7.1 1.6 8.0 W Pin1 (mm) Quadrant 16.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TSC2000IPWR TSSOP PW 20 2000 367.0 367.0 38.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated