SCALETM-2 2SP0115T2A0(C)-FF225R17ME4 2SP0115T2A0-FF225R17ME4 and 2SP0115T2A0C-FF225R17ME4 Data Sheet Compact, high-performance, plug-and-play dual-channel IGBT driver based on SCALETM-2 technology for individual and parallel-connected modules Abstract The SCALETM-2 plug-and-play driver 2SP0115T2A0-FF225R17ME4 / 2SP0115T2A0C-FF225R17ME4 (Coated version using ELPEGUARD SL 1307 FLZ/2 from Lackwerke Peters with a typical thickness of 50m) is a compact dual-channel intelligent gate driver designed for Infineon's EconoDUALTM IGBTs FF225R17ME4. The driver features an electrical interface with a built-in DC/DC power supply. For drivers adapted to other types of high-power and high-voltage IGBT modules, refer to www.power.com/gate-driver/go/plug-and-play Features Applications Plug-and-play solution Allows parallel connection of IGBT modules Shortens application development time Extremely reliable; long service life Built-in DC/DC power supply 20-pin flat cable interface Duty cycle 0... 100% Active clamping of V at turn-off IGBT short-circuit protection Monitoring of supply voltage Safe isolation to EN 50178 UL compliant Suitable for FF225R17ME4 ce Wind-power converters Industrial drives UPS Power-factor correctors Traction Railroad power supplies Welding SMPS Radiology and laser technology Research and many others EconoDUAL is a trademark of Infineon Technologies AG, Munich www.power.com/gate-driver Page 1 SCALETM-2 2SP0115T2A0(C)-FF225R17ME4 Data Sheet Safety Notice! The data contained in this data sheet is intended exclusively for technically trained staff. Handling all highvoltage equipment involves risk to life. Strict compliance with the respective safety regulations is mandatory! Any handling of electronic devices is subject to the general specifications for protecting electrostatic-sensitive devices according to international standard IEC 60747-1, Chapter IX or European standard EN 100015 (i.e. the workplace, tools, etc. must comply with these standards). Otherwise, this product may be damaged. Important Product Documentation This data sheet contains only product-specific data. For a detailed description, must-read application notes and common data that apply to the whole series, please refer to "Description & Application Manual for 2SP0115T SCALE-2 IGBT Drivers" on www.power.com/gate-driver/go/2SP0115T. When applying SCALE-2 plug-and-play drivers, please note that these drivers are specifically adapted to a particular type of IGBT module. Therefore, the type designation of SCALE-2 plug-and-play drivers also includes the type designation of the corresponding IGBT module. These drivers are not valid for IGBT modules other than those specified. Incorrect use may result in failure. Mechanical Dimensions Dimensions: Refer to "Description & Application Manual for 2SP0115T SCALE-2 IGBT Drivers" Mounting principle: Soldered onto EconoDUALTM module FF225R17ME4 Absolute Maximum Ratings Parameter Remarks Min Supply voltage VCC Logic input and output voltages SOx current Gate peak current Iout Average supply current ICC Output power per gate VCC to GND To GND Fault condition, total current Note 1 Note 2 Ambient temperature 70C (Note 3) Ambient temperature 85C (Note 3) 0 16 V -0.5 VCC+0.5 V 20 mA -8 +15 A 290 mA 1.2 W 1 W 28 kHz 5000 VAC(eff) Switching frequency f Test voltage (50Hz/1min.) Primary to secondary (Note 16) DC-link voltage |dV/dt| Operating voltage Secondary to secondary (Note 16) Note 4 Rate of change of input to output voltage Primary/secondary, secondary/secondary www.power.com/gate-driver Max Unit 4000 VAC(eff) 1200 V 50 kV/s 1700 Vpeak Page 2 SCALETM-2 2SP0115T2A0(C)-FF225R17ME4 Data Sheet Parameter Remarks Min Max Unit Operating temperature Storage temperature Surface temperature Note 20 Note 21 Only 2SP0115T2A0C-FF225R17ME4 (Note 22) -20 -40 85 50 125 C C C Recommended Operating Conditions Parameter Remarks Min Typ Max Unit Supply voltage VCC Resistance from TB to GND SOx current To GND Blocking time 0, ext. value Fault condition, 3.3V logic 14.5 128 15 15.5 4 V k mA Min Typ Max Unit Electrical Characteristics Power Supply Remarks Supply current ICC Efficiency Coupling capacitance Cio Without load Internal DC/DC converter Primary side to secondary side, total, per channel Power Supply Monitoring Remarks Min Typ Max Unit Supply threshold VCC 11.9 11.3 0.35 12.1 11.5 0.35 5 4.7 0.15 12.6 12.0 13.3 12.7 12.6 12.0 13.1 12.5 5.15 4.85 5.3 5 Monitoring hysteresis Primary side, clear fault Primary side, set fault (Note 5) Primary side, set/clear fault Secondary side, clear fault Secondary side, set fault (Note 6) Secondary side, set/clear fault Secondary side, clear fault Secondary side, set fault (Note 6) Secondary side, set/clear fault V V V V V V V V V Logic Inputs and Outputs Remarks Min Typ Max Unit Input impedance Turn-on threshold Turn-off threshold SOx output voltage V(INx) > 3V (Note 7) V(INx) (Note 8) V(INx) (Note 8) Fault condition, I(SOx) < 8mA 3.5 4.1 2.6 1.3 4.6 k V V V Monitoring hysteresis Supply threshold Visox-Veex Monitoring hysteresis Supply threshold Veex-VCOMx www.power.com/gate-driver 33 85 23 mA % pF 0.7 Page 3 SCALETM-2 2SP0115T2A0(C)-FF225R17ME4 Data Sheet Short-circuit Protection Remarks Vce-monitoring threshold Response time Delay to IGBT turn-off Blocking time Between auxiliary terminals DC-link voltage > 550V (Note 9) After the response time (Note 10) After fault (Note 11) Timing Characteristics Remarks Turn-on delay td(on) Turn-off delay td(off) Jitter of turn-on delay Jitter of turn-off delay Output rise time tr(out) Output fall time tf(out) Dead time between outputs Jitter of dead time Transmission delay of fault state Note 12 Note 12 Note 18 Note 18 Gx to Ex (Note 13) Gx to Ex (Note 13) Half-bridge mode (Note 19) Half-bridge mode Note 14 Outputs Remarks Turn-on gate resistor Rg(on) Turn-off gate resistor Rg(off) Gate voltage at turn-on Gate-voltage at turn-off Note 15 Note 15 Min Typ Max 10.2 5.4 1.4 90 Min Typ V s s ms Max 75 65 2 4 5 10 3 50 400 Min Typ Gate resistance to COMx Unit ns ns ns ns ns ns s ns ns Max 3.3 8.2 15 -9.2 -7.1 4.7 P=0W P=1.2W Unit Unit V V V k Electrical Isolation Remarks Min Typ Max Unit Test voltage (50Hz/1s) Primary to secondary side (Note 16) 5000 5050 5100 Veff Secondary to secondary side (Note 16) 4000 4050 4100 Veff Primary to secondary side (Note 17) Secondary to secondary side (Note 17) Primary to secondary side 1768 1700 12.6 Vpeak Vpeak mm Secondary to secondary side 6.6 mm Primary to NTC 6.5 mm Primary to secondary side Secondary to secondary side Primary to NTC 12.3 6.6 6.5 mm mm mm Partial discharge extinction volt. Creepage distance Clearance distance All data refer to +25C and VCC = 15V unless otherwise specified www.power.com/gate-driver Page 4 SCALETM-2 2SP0115T2A0(C)-FF225R17ME4 Data Sheet Footnotes to the Key Data 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11) 12) 13) 14) 15) 16) 17) 18) 19) 20) 21) 22) The gate current is limited by the gate resistors located on the driver. If the specified value is exceeded, this indicates a driver overload. It should be noted that the driver is not protected against overload. If the specified value is exceeded, this indicates a driver overload. It should be noted that the driver is not protected against overload. From 70C to 85C, the maximum permissible output power can be linearly interpolated from the given data. This limit is due to active clamping. Refer to the "Description & Application Manual for 2SP0115T SCALE-2 IGBT Drivers". Undervoltage monitoring of the primary-side supply voltage (VCC to GND). If the voltage drops below this limit, a fault is transmitted to the corresponding outputs and the IGBTs are switched off. Undervoltage monitoring of the secondary-side supply voltage (Visox to Veex and Veex to COMx which correspond with the approximate turn-on and turn-off gate-emitter voltages). If the corresponding voltage drops below this limit, the IGBT is switched off and a fault is transmitted to the corresponding output. The input impedance can be modified to values <18 k (customer-specific solution). Turn-on and turn-off threshold values can be increased (customer-specific solution). The resulting pulse width of the direct output of the gate drive unit for short-circuit type I (excluding the delay of the gate resistors) is the sum of response time plus delay to IGBT turn-off. The turn-off event of the IGBT is delayed by the specified time after the response time. Factory set value. The blocking time can be reduced with an external resistor. Refer to the "Description & Application Manual for 2SP0115T SCALE-2 IGBT Drivers". Measured from the transition of the turn-on or turn-off command at the driver input to direct output of the gate drive unit (excluding the delay of the gate resistors). Output rise and fall times are measured between 10% and 90% of the nominal output swing with an output load of 10 and 40nF. The values are given for the driver side of the gate resistors. The time constant of the output load in conjunction with the present gate resistors leads to an additional delay at the load side of the gate resistors. Transmission delay of the fault state from the secondary side to the primary status outputs. The gate resistors can be leaded or surface mounted. Power Integrations reserves the right to determine which type will be used. Typically, higher quantities will be produced with SMD resistors and small quantities with leaded resistors. HiPot testing (= dielectric testing) must generally be restricted to suitable components. This gate driver is suited for HiPot testing. Nevertheless, it is strongly recommended to limit the testing time to 1s slots as stipulated by EN 50178. Excessive HiPot testing at voltages much higher than 1200VAC(eff) may lead to insulation degradation. No degradation has been observed over 1min. testing at 5000VAC(eff). The transformer of every production sample shipped to customers has undergone 100% testing at the given value for 1s. Partial discharge measurement is performed in accordance with IEC 60270 and isolation coordination specified in EN 50178. The partial discharge extinction voltage between primary and either secondary side is coordinated for safe isolation to EN 50178. Jitter measurements are performed with input signals INx switching between 0V and 15V referred to GND, with a corresponding rise time and fall time of 8ns. Note that the dead time may vary from sample to sample. A tolerance of approximately 20% may be expected. If higher timing precisions are required, Power Integrations recommends using direct mode and generating the dead time externally. A version with extended operating temperature range of -40C...85C (2SP0115T2B0) can also be supplied. The storage temperature inside the original package (1) or in case the coating material of coated products may touch external parts (2) must be limited to the given value. Otherwise, it is limited to 90C. The component surface temperature, which may strongly vary depending on the operating condition, must be limited to the given value for coated driver versions to ensure long-term reliability of the coating material. www.power.com/gate-driver Page 5 SCALETM-2 2SP0115T2A0(C)-FF225R17ME4 Data Sheet Legal Disclaimer The statements, technical information and recommendations contained herein are believed to be accurate as of the date hereof. All parameters, numbers, values and other technical data included in the technical information were calculated and determined to our best knowledge in accordance with the relevant technical norms (if any). They may base on assumptions or operational conditions that do not necessarily apply in general. We exclude any representation or warranty, express or implied, in relation to the accuracy or completeness of the statements, technical information and recommendations contained herein. No responsibility is accepted for the accuracy or sufficiency of any of the statements, technical information, recommendations or opinions communicated and any liability for any direct, indirect or consequential loss or damage suffered by any person arising therefrom is expressly disclaimed. www.power.com/gate-driver Page 6 SCALETM-2 2SP0115T2A0(C)-FF225R17ME4 Data Sheet Ordering Information Our international terms and conditions of sale apply. Power Integrations Driver Type # Related IGBT 2SP0115T2A0-FF225R17ME4 (Temperature range -20C...85C) 2SP0115T2A0C-FF225R17ME4 (Temperature range -20C...85C, conformal coating) FF225R17ME4 FF225R17ME4 Product home page: www.power.com/gate-driver/go/2SP0115T Refer to www.power.com/gate-driver/go/nomenclature for information on driver nomenclature Information about Other Products For other drivers, evaluation systems product documentation and application support Please click: www.power.com (c) 2009...2019 Power Integrations Switzerland GmbH. We reserve the right to make any technical modifications without prior notice. www.power.com/gate-driver All rights reserved. Version 2.0 from 2019-04-03 Page 7 SCALETM-2 2SP0115T2A0(C)-FF225R17ME4 Data Sheet Power Integrations Sales Offices WORLD HEADQUARTERS 5245 Hellyer Avenue San Jose, CA 95138 USA Tel: +1-408-414-9200 Fax: +1-408-414-9765 Email: usasales@power.com AMERICAS EAST 7360 McGinnis Ferry Road Suite 225 Suwannee, GA 30024 USA Tel: +1-678-957-0724 Fax: +1-678-957-0784 Email: usasales@power.com AMERICAS CENTRAL 333 Sheridan Road Winnetka, IL 60093 USA Tel: +1-847-721-6293 Email: usasales@power.com AMERICAS WEST 5245 Hellyer Avenue San Jose, CA 95138 USA Tel: +1-408-414-8778 Fax: +1-408-414-3760 Email: usasales@power.com CHINA (Shanghai) Room 2410, Charity Plaza No. 88 North Caoxi Road Shanghai, 200030 China Tel: +86-21-6354-6323 Fax: +86-21-6354-6325 Email: chinasales@power.com CHINA (Shenzhen) 17/F, Hivac Building, No 2 Keji South 8th Road, Nanshan District Shenzhen, 518057 China Tel: +86-755-8672-8689 Fax: +86-755-8672-8690 Email: chinasales@power.com GERMANY (AC-DC/LED Sales) Einsteinring 24 85609 Aschheim, Germany Tel: +49-89-5527-39100 Fax: +49-89-1228-5374 Email: eurosales@power.com GERMANY (Gate Driver Sales) HellwegForum 1 59469 Ense, Germany Tel: +49-2938-64-39990 Email: gate-drivers.sales@power.com INDIA (Bangalore) #1, 14th Main Road Vasanthangar Bangalore, 560052 India Tel 1: +91-80-4113-8020 Tel 2: +91-80-4113-8028 Fax: +91-80-4113-8023 Email: indiasales@power.com INDIA (Mumbai) Unit: 106-107, Sagar Tech Plaza-B Sakinaka, Andheri Kurla Road Mumbai, Maharashtra 400072 India Tel 1: +91-22-4003-3700 Tel 2: +91-22-4003-3600 Email: indiasales@power.com INDIA (New Delhi) #45, Top Floor Okhla Industrial Area, Phase - III New Delhi, 110020 India Tel 1: +91-11-4055-2351 Tel 2: +91-11-4055-2353 Email: indiasales@power.com ITALY Via Milanese 20 20099 Sesto San Giovanni (MI), Italy Tel: +39-02-4550-8708 Email: eurosales@power.com JAPAN Kosei Dai-3 Bldg. 2-12-11, Shin-Yokohama, Kohoku-ku Yokohama-shi, Kanagawa Japan 222-0033 Tel: +81-45-471-1021 Fax: +81-45-471-3717 Email: japansales@power.com KOREA RM602, 6FL, 22 Teheran-ro 87-gil, Gangnam-gu Seoul, 06164 Korea Tel: +82-2-2016-6610 Fax: +82-2-2016-6630 Email: koreasales@power.com SINGAPORE 51 Newton Road #19-01/05 Goldhill Plaza Singapore, 308900 Tel 1: +65-6358-2160 Tel 2: +65-6358-4480 Fax: +65-6358-2015 Email: singaporesales@power.com TAIWAN 5F, No. 318, Nei Hu Rd., Sec. 1 Nei Hu Dist. Taipei, 114 Taiwan Tel: +886-2-2659-4570 Fax: +886-2-2659-4550 Email: taiwansales@power.com UNITED KINGDOM Building 5, Suite 21 The Westbrook Centre Milton Road Cambridge, CB4 1YG United Kingdom Tel: +44-7823-557-484 Email: eurosales@power.com www.power.com/gate-driver Page 8