93AA46A/B/C, 93LC46A/B/C, 93C46A/B/C 93AA56A/B/C, 93LC56A/B/C, 93C56A/B/C 93AA66A/B/C, 93LC66A/B/C, 93C66A/B/C 93AA76A/B/C, 93LC76A/B/C, 93C76A/B/C 93AA86A/B/C, 93LC86A/B/C, 93C86A/B/C 1K-16K Microwire Compatible Serial EEPROMs Features: Description: * Densities from 1 Kbits through 16 Kbits * Low-power CMOS technology * Available with or without ORG function: Microchip Technology Inc. supports the 3-wire Microwire bus with low-voltage serial Electrically Erasable PROMs (EEPROM) that range in density from 1 Kbits up to 16 Kbits. Each density is available with and without the ORG functionality, and selected by the part number ordered. Advanced CMOS technology makes these devices ideal for low-power, nonvolatile memory applications. The entire series of Microwire devices are available in the standard 8-lead PDIP and SOIC packages, as well as the more advanced packaging such as the 8-lead MSOP, 8-lead TSSOP, 6-lead SOT-23, and 8-lead DFN (2x3). All packages are Pb-free. With ORG function: - ORG pin at Logic Low: 8-bit word - ORG pin at Logic High: 16-bit word Without ORG function: * * * * * * * * * * * - `A' version: 8-bit word - `B' version: 16-bit word Program Enable pin: - Write-protect for entire array (93XX76C and 93XX86C only) Self-timed Erase/Write cycles (including auto-erase) Automatic ERAL before WRAL Power-on/off data protection circuitry Industry standard 3-wire serial I/O Device Status signal (Ready/Busy) Sequential Read function 1,000,000 E/W cycles Data retention > 200 years Pb-free and RoHS compliant Temperature ranges supported: - Industrial (I) -40C to +85C - Automotive (E) -40C to +125C Pin Diagrams (not to scale) PDIP/SOIC (P, SN) (1,3) 1 8 VCC CLK 2 7 PE CS NC 1 8 ORG VCC 2 7 VSS CS 3 6 DO CLK 4 5 DI (2,3) (1,3) DI 3 6 ORG DO 4 5 VSS DFN (MC) CS CLK DI DO 1 2 3 4 8 7 6 5 VCC PE(2,3) ORG(1,3) VSS TSSOP/MSOP (ST, MS) Pin Function Table Name ROTATED SOIC (ex: 93LC46BX) Function CS CLK 1 2 3 4 8 7 6 5 SOT-23 (OT) VCC DO PE(2,3) V SS ORG(1,3) DI VSS 1 6 VCC 2 5 CS 3 4 CLK CS Chip Select CLK Serial Data Clock DI Serial Data Input DO Serial Data Output VSS Ground 2: PE pin: Only on 93XX76C/86C. PE Program Enable 3: ORG/PE: No internal connections on 93XXA/B. ORG Memory Configuration VCC Power Supply Note: DI DO Note 1: ORG pin: Only on 93XX46C/56C/66C/76C/86C. ORG and PE functionality not available in all products. See Table 1-1, Device Selection Table. (c) 2007 Microchip Technology Inc. DS21929D-page 1 93XX46X/56X/66X/76X/86X TABLE 1-1: DEVICE SELECTION TABLE Density (Kbits) VCC Range ORG Pin Organization (Words) PE Pin Temp Range Packages 93AA46A 1 1.8-5.5 No 128 x 8 bits No I P, SN, ST, MS, OT, MC 93AA46B 1 1.8-5.5 No 64 x 16 bits No I P, SN, ST, MS, OT, MC 93AA46C 1 1.8-5.5 Yes Selectable x8 or x16 No I P, SN, ST, MS, MC 93LC46A 1 2.5-5.5 No 128 x 8 bits No I, E P, SN, ST, MS, OT, MC 93LC46B 1 2.5-5.5 No 64 x 16 bits No I, E P, SN, ST, MS, OT, MC 93LC46C 1 2.5-5.5 Yes Selectable x8 or x16 No I, E P, SN, ST, MS, MC 93C46A 1 4.5-5.5 No 128 x 8 bits No I, E P, SN, ST, MS, OT, MC 93C46B 1 4.5-5.5 No 64 x 16 bits No I, E P, SN, ST, MS, OT, MC 93C46C 1 4.5-5.5 Yes Selectable x8 or x16 No I, E P, SN, ST, MS, MC Part Number 93XX46A/B/C 93AA46AX/BX/CX, 93LC46AX/BX/CX, 93C46AX/BX/CX (Alternate pinout with die rotated 90) 93AA46AX 1 1.8-5.5 93AA46BX 1 1.8-5.5 93AA46CX 1 1.8-5.5 93LC46AX 1 2.5-5.5 93LC46BX 1 2.5-5.5 No 128 x 8 bits No I P, SN, ST, MS, OT, MC No 64 x 16 bits No I P, SN, ST, MS, OT, MC Yes Selectable x8 or x16 No I P, SN, ST, MS, MC No 128 x 8 bits No I, E P, SN, ST, MS, OT, MC No 64 x 16 bits No I, E P, SN, ST, MS, OT, MC 93LC46CX 1 2.5-5.5 Yes Selectable x8 or x16 No I, E P, SN, ST, MS, MC 93C46AX 1 4.5-5.5 No 128 x 8 bits No I, E P, SN, ST, MS, OT, MC 93C46BX 1 4.5-5.5 No 64 x 16 bits No I, E P, SN, ST, MS, OT, MC 93C46CX 1 4.5-5.5 Yes Selectable x8 or x16 No I, E P, SN, ST, MS, MC 93AA56A 2 1.8-5.5 No 256 x 8 bits No I 93AA56B 2 1.8-5.5 No 128 x 16 bits No I P, SN, ST, MS, OT, MC 93AA56C 2 1.8-5.5 Yes Selectable x8 or x16 No I P, SN, ST, MS, MC 93LC56A 2 2.5-5.5 No 256 x 8 bits No I, E P, SN, ST, MS, OT, MC 93LC56B 2 2.5-5.5 No 128 x 16 bits No I, E P, SN, ST, MS, OT, MC 93LC56C 2 2.5-5.5 Yes Selectable x8 or x16 No I, E P, SN, ST, MS, MC 93C56A 2 4.5-5.5 No 256 x 8 bits No I, E P, SN, ST, MS, OT, MC 93C56B 2 4.5-5.5 No 128 x 16 bits No I, E P, SN, ST, MS, OT, MC 93C56C 2 4.5-5.5 Yes Selectable x8 or x16 No I, E P, SN, ST, MS, MC 93AA66A 4 1.8-5.5 No 512 x 8 bits No I 93AA66B 4 1.8-5.5 No 256 x 16 bits No I P, SN, ST, MS, OT, MC 93AA66C 4 1.8-5.5 Yes Selectable x8 or x16 No I P, SN, ST, MS, MC 93LC66A 4 2.5-5.5 No 512 x 8 bits No I, E P, SN, ST, MS, OT, MC 93LC66B 4 2.5-5.5 No 256 x 16 bits No I, E P, SN, ST, MS, OT, MC 93LC66C 4 2.5-5.5 Yes Selectable x8 or x16 No I, E P, SN, ST, MS, MC 93C66A 4 4.5-5.5 No 512 x 8 bits No I, E P, SN, ST, MS, OT, MC 93C66B 4 4.5-5.5 No 256 x 16 bits No I, E P, SN, ST, MS, OT, MC 93C66C 4 4.5-5.5 Yes Selectable x8 or x16 No I, E P, SN, ST, MS, MC 93XX56A/B/C P, SN, ST, MS, OT, MC 93XX66A/B/C DS21929D-page 2 P, SN, ST, MS, OT, MC (c) 2007 Microchip Technology Inc. 93XX46X/56X/66X/76X/86X TABLE 1-1: Part Number DEVICE SELECTION TABLE (CONTINUED) Density (Kbits) VCC Range ORG Pin Organization (Words) PE Pin Temp Range 8 1.8-5.5 No 1024 x 8 bits No I Packages 93XX76A/B/C 93AA76A OT 93AA76B 8 1.8-5.5 No 512 x 16 bits No I OT 93AA76C 8 1.8-5.5 Yes Selectable x8 or x16 Yes I P, SN, ST, MS, MC 93LC76A 8 2.5-5.5 No 1024 x 8 bits No I, E OT 93LC76B 8 2.5-5.5 No 512 x 16 bits No I, E OT 93LC76C 8 2.5-5.5 Yes Selectable x8 or x16 Yes I, E P, SN, ST, MS, MC 93C76A 8 4.5-5.5 No 1024 x 8 bits No I, E OT 93C76B 8 4.5-5.5 No 512 x 16 bits No I, E OT 93C76C 8 4.5-5.5 Yes Selectable x8 or x16 Yes I, E P, SN, ST, MS, MC 93AA86A 16 1.8-5.5 No 2048 x 8 bits No I 93AA86B 16 1.8-5.5 No 1024 x 16 bits No I OT 93AA86C 16 1.8-5.5 Yes Selectable x8 or x16 Yes I P, SN, ST, MS, MC 93XX86A/B/C OT 93LC86A 16 2.5-5.5 No 2048 x 8 bits No I, E OT 93LC86B 16 2.5-5.5 No 1024 x 16 bits No I, E OT 93LC86C 16 2.5-5.5 Yes Selectable x8 or x16 Yes I, E P, SN, ST, MS, MC 93C86A 16 4.5-5.5 No 2048 x 8 bits No I, E OT 93C86B 16 4.5-5.5 No 1024 x 16 bits No I, E OT 93C86C 16 4.5-5.5 Yes Selectable x8 or x16 Yes I, E P, SN, ST, MS, MC (c) 2007 Microchip Technology Inc. DS21929D-page 3 93XX46X/56X/66X/76X/86X 2.0 ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings() VCC .............................................................................................................................................................................7.0V All inputs and outputs w.r.t. VSS ......................................................................................................... -0.6V to VCC +1.0V Storage temperature ...............................................................................................................................-65C to +150C Ambient temperature with power applied ................................................................................................-40C to +125C ESD protection on all pins ...................................................................................................................................................... 4 kV NOTICE: Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. TABLE 2-1: DC CHARACTERISTICS All parameters apply over the specified ranges unless otherwise noted. Param. Symbol No. Parameter VCC = 1.8V to 5.5V Industrial (I): TA = -40C to +85C Automotive (E): TA = -40C to +125C Min. Typ. Max. Units Conditions D1 VIH1 VIH2 High-level input voltage 2.0 0.7 VCC -- -- VCC +1 VCC +1 V V VCC 2.7V VCC < 2.7V D2 VIL1 VIL2 Low-level input voltage -0.3 -0.3 -- -- 0.8 0.2 VCC V V VCC 2.7V VCC < 2.7V D3 VOL1 VOL2 Low-level output voltage -- -- -- -- 0.4 0.2 V V IOL = 2.1 mA, VCC = 4.5V IOL = 100 A, VCC = 2.5V D4 VOH1 VOH2 High-level output voltage 2.4 VCC-0.2 -- -- -- -- V V IOH = -400 A, VCC = 4.5V IOH = -100 A, VCC = 2.5V D5 ILI Input leakage current -- -- 1 A VIN = VSS to VCC D6 ILO Output leakage current -- -- 1 A VOUT = VSS to VCC D7 CIN, COUT Pin capacitance (all inputs/outputs) -- -- 7 pF VIN/VOUT = 0V (Note 1) TA = 25C, FCLK = 1 MHz D8 ICC write Write current -- -- 2 mA FCLK = 3 MHz, VCC = 5.5V (93XX46X/56X/66X) -- -- 3 mA -- 500 -- A FCLK = 3 MHz, VCC = 5.5V (93XX76X/86X) FCLK = 2 MHz, VCC = 2.5V D9 ICC read Read current -- -- -- -- -- 100 1 500 -- mA A A FCLK = 3 MHz, VCC = 5.5V FCLK = 2 MHz, VCC = 3.0V FCLK = 2 MHz, VCC = 2.5V D10 ICCS Standby current -- -- -- -- 1 5 A A I-Temp (Note 2, 3) E-Temp CLK = Cs = 0V ORG = DI = VSS or VCC D11 VPOR VCC voltage detect -- -- 1.5V 3.8V -- -- V V 93AAX6A/B/C, 93LCX6A/B/C, 93CX6A/B/C (Note 1) Note 1: 2: 3: This parameter is periodically sampled and not 100% tested. ORG and PE pins not available on `A' or `B' versions. Ready/Busy status must be cleared from DO, see Section 4.4 "Data Out (DO)". DS21929D-page 4 (c) 2007 Microchip Technology Inc. 93XX46X/56X/66X/76X/86X TABLE 2-2: AC CHARACTERISTICS All parameters apply over the specified ranges unless otherwise noted. Param. Symbol No. Parameter VCC = 1.8V to 5.5V Industrial (I): TA = -40C to +85C Automotive (E): TA = -40C to +125C Min. Max. Units Conditions A1 FCLK Clock frequency -- 3 2 1 MHz MHz MHz 4.5V VCC < 5.5V 2.5V VCC < 4.5V 1.8V VCC < 2.5V A2 TCKH Clock high time 200 250 450 -- ns ns ns 4.5V VCC < 5.5V 2.5V VCC < 4.5V 1.8V VCC < 2.5V A3 TCKL Clock low time 100 200 450 -- ns ns ns 4.5V VCC < 5.5V 2.5V VCC < 4.5V 1.8V VCC < 2.5V A4 TCSS Chip Select setup time 50 100 250 -- ns ns ns 4.5V VCC < 5.5V 2.5V VCC < 4.5V 1.8V VCC < 2.5V A5 TCSH Chip Select hold time 0 -- ns 1.8V VCC < 5.5V A6 TCSL Chip Select low time 250 -- ns 1.8V VCC < 5.5V A7 TDIS Data input setup time 50 100 250 -- ns ns ns 4.5V VCC < 5.5V 2.5V VCC < 4.5V 1.8V VCC < 2.5V A8 TDIH Data input hold time 50 100 250 -- ns ns ns 4.5V VCC < 5.5V 2.5V VCC < 4.5V 1.8V VCC < 2.5V A9 TPD Data output delay time -- 100 ns 4.5V VCC < 5.5V, CL = 100 pF (93C76X/86X) -- 200 250 400 ns ns ns 4.5V VCC < 5.5V, CL = 100 pF 2.5V VCC < 4.5V, CL = 100 pF 1.8V VCC < 2.5V, CL = 100 pF A10 TCZ Data output disable time -- 100 200 ns ns 4.5V VCC < 5.5V, (Note 1) 1.8V VCC < 4.5V, (Note 1) A11 TSV Status valid time -- 200 300 500 ns ns ns 4.5V VCC < 5.5V, CL = 100 pF 2.5V VCC < 4.5V, CL = 100 pF 1.8V VCC < 2.5V, CL = 100 pF A12 TWC Program cycle time -- 5 ms Erase/Write mode 93XX76X/86X (AA and LC versions) -- 6 ms 93XX46X/56X/66X (AA and LC versions) A13 TWC A14 TEC A15 TWL A16 -- Note 1: 2: -- 2 ms 93C46X/56X/66X/76X/86X Program cycle time -- 6 ms ERAL mode, 4.5V VCC 5.5V -- 15 ms WRAL mode, 4.5V VCC 5.5V Endurance 1M -- cycles 25C, VCC = 5.0V, (Note 2) This parameter is periodically sampled and not 100% tested. This application is not tested but ensured by characterization. For endurance estimates in a specific application, please consult the Total EnduranceTM Model which may be downloaded from Microchip's web site at www.microchip.com. (c) 2007 Microchip Technology Inc. DS21929D-page 5 93XX46X/56X/66X/76X/86X FIGURE 2-1: CS SYNCHRONOUS DATA TIMING VIH TCSS VIL TCKH TCKL TCSH VIH CLK VIL TDIS TDIH VIH DI VIL TPD TPD DO (Read) VOH VOL TCZ TSV DO VOH (Program) VOL Note: TCZ Status Valid Status Valid Time (TSV) is relative to CS. DS21929D-page 6 (c) 2007 Microchip Technology Inc. 93XX46X/56X/66X/76X/86X TABLE 2-3: INSTRUCTION SET FOR 93XX46A/B/C Instruction SB Opcode Address 93XX46B OR 93XX46C WITH ORG = 1 Data Out Req. CLK Cycles -- (RDY/BSY) 9 Data In (16-BIT WORD ORGANIZATION) ERASE 1 11 A5 A4 A3 A2 A1 A0 ERAL 1 00 1 0 x x x x -- (RDY/BSY) 9 EWDS 1 00 0 0 x x x x -- High-Z 9 EWEN 1 00 1 1 x x x x -- High-Z 9 READ 1 10 A5 A4 A3 A2 A1 A0 -- D15-D0 25 WRITE 1 01 A5 A4 A3 A2 A1 A0 D15-D0 (RDY/BSY) 25 WRAL 1 00 D15-D0 (RDY/BSY) 25 0 93XX46A OR 93XX46C WITH ORG = 0 1 x x x (8-BIT WORD ORGANIZATION) ERASE 1 11 ERAL 1 00 1 0 x x x x EWDS 1 00 0 0 x x x EWEN 1 00 1 1 x x x READ 1 10 WRITE 1 01 WRAL 1 00 TABLE 2-4: x A6 A5 A4 A3 A2 A1 A0 -- (RDY/BSY) 10 x -- (RDY/BSY) 10 x x -- High-Z 10 x x -- High-Z 10 A6 A5 A4 A3 A2 A1 A0 -- D7-D0 18 A6 A5 A4 A3 A2 A1 A0 D7-D0 (RDY/BSY) 18 D7-D0 (RDY/BSY) 18 Data In Data Out Req. CLK Cycles -- (RDY/BSY) 11 0 1 x x x x x INSTRUCTION SET FOR 93XX56A/B/C Instruction SB Opcode Address 93XX56B OR 93XX56C WITH ORG = 1 (16-BIT WORD ORGANIZATION) ERASE 1 11 x ERAL 1 00 1 0 x x x x x x -- (RDY/BSY) 11 EWDS 1 00 0 0 x x x x x x -- High-Z 11 EWEN 1 00 1 1 x x x x x x -- High-Z 11 READ 1 10 x A6 A5 A4 A3 S2 A1 A0 D15-D0 27 WRITE 1 01 x A6 A5 A4 A3 S2 A1 A0 D15-D0 (RDY/BSY) 27 WRAL 1 00 0 D15-D0 (RDY/BSY) 27 -- (RDY/BSY) 12 -- (RDY/BSY) 12 93XX56A OR 93XX56C WITH ORG = 0 ERASE 1 11 x ERAL 1 00 1 A6 A5 A4 A3 A2 A1 A0 1 x x x x x x -- (8-BIT WORD ORGANIZATION) A7 A6 A5 A4 A3 A2 A1 A0 0 x x x x x x x EWDS 1 00 0 0 x x x x x x x -- High-Z 12 EWEN 1 00 1 1 x x x x x x x -- High-Z 12 READ 1 10 x A7 A6 A5 A4 A3 A2 A1 A0 -- D7-D0 20 WRITE 1 01 x A7 A6 A5 A4 A3 A2 A1 A0 D7-D0 (RDY/BSY) 20 WRAL 1 00 0 D7-D0 (RDY/BSY) 20 (c) 2007 Microchip Technology Inc. 1 x x x x x x x DS21929D-page 7 93XX46X/56X/66X/76X/86X TABLE 2-5: INSTRUCTION SET FOR 93XX66A/B/C Instruction SB Opcode Address 93XX66B OR 93XX66C WITH ORG = 1 Data Out Req. CLK Cycles -- (RDY/BSY) 11 Data In (16-BIT WORD ORGANIZATION) ERASE 1 11 A7 A6 A5 A4 A3 A2 A1 A0 ERAL 1 00 1 0 x x x x x x -- (RDY/BSY) 11 EWDS 1 00 0 0 x x x x x x -- High-Z 11 EWEN 1 00 1 1 x x x x x x -- High-Z 11 READ 1 10 A7 A6 A5 A4 A3 A2 A1 A0 -- D15-D0 27 WRITE 1 01 A7 A6 A5 A4 A3 A2 A1 A0 D15-D0 (RDY/BSY) 27 WRAL 1 00 D15-D0 (RDY/BSY) 27 -- (RDY/BSY) 12 0 93XX66A OR 93XX66C WITH ORG = 0 1 x x x x x x (8-BIT WORD ORGANIZATION) ERASE 1 11 ERAL 1 00 1 0 x x x x x x x -- (RDY/BSY) 12 EWDS 1 00 0 0 x x x x x x x -- High-Z 12 EWEN 1 00 1 1 x x x x x x x -- High-Z 12 READ 1 10 A8 A7 A6 A5 A4 A3 A2 A1 A0 -- D7-D0 20 WRITE 1 01 A8 A7 A6 A5 A4 A3 A2 A1 A0 D7-D0 (RDY/BSY) 20 WRAL 1 00 D7-D0 (RDY/BSY) 20 Data In Data Out Req. CLK Cycles -- (RDY/BSY) 13 TABLE 2-6: A8 A7 A6 A5 A4 A3 A2 A1 A0 0 1 x x x x x x x INSTRUCTION SET FOR 93XX76A/B/C Instruction SB Opcode Address 93XX76B OR 93XX76C WITH ORG = 1 (16-BIT WORD ORGANIZATION) ERASE 1 11 x A8 A7 A6 A5 A4 A3 A2 A1 A0 ERAL 1 00 1 0 x x x x x x x x -- (RDY/BSY) 13 EWDS 1 00 0 0 x x x x x x x x -- High-Z 13 EWEN 1 00 1 1 x x x x x x x x -- High-Z 13 READ 1 10 x A8 A7 A6 A5 A4 A3 A2 A1 A0 -- D15-D0 29 WRITE 1 01 x A8 A7 A6 A5 A4 A3 A2 A1 A0 D15-D0 (RDY/BSY) 29 WRAL 1 00 0 D15-D0 (RDY/BSY) 29 -- (RDY/BSY) 14 -- (RDY/BSY) 14 1 x 93XX76A OR 93XX76C WITH ORG = 0 ERASE 1 11 x ERAL 1 00 1 x x x x x x x (8-BIT WORD ORGANIZATION) A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 0 x x x x x x x x x EWDS 1 00 0 0 x x x x x x x x x -- High-Z 14 EWEN 1 00 1 1 x x x x x x x x x -- High-Z 14 READ 1 10 x A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 -- D7-D0 22 WRITE 1 01 x A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 D7-D0 (RDY/BSY) 22 WRAL 1 00 0 D7-D0 (RDY/BSY) 22 DS21929D-page 8 1 x x x x x x x x x (c) 2007 Microchip Technology Inc. 93XX46X/56X/66X/76X/86X TABLE 2-7: Instruction INSTRUCTION SET FOR 93XX86A/B/C SB Opcode Address 93XX86B OR 93XX86C WITH ORG = 1 Data Out Req. CLK Cycles -- (RDY/BSY) 13 Data In (16-BIT WORD ORGANIZATION) ERASE 1 11 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 ERAL 1 00 1 0 x x x x x x x x -- (RDY/BSY) 13 EWDS 1 00 0 0 x x x x x x x x -- High-Z 13 EWEN 1 00 1 1 x x x x x x x x -- High-Z 13 READ 1 10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 -- D15-D0 29 WRITE 1 01 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 D15-D0 (RDY/BSY) 29 WRAL 1 00 D15-D0 (RDY/BSY) 29 -- (RDY/BSY) 14 0 1 x 93XX86A OR 93XX86C WITH ORG = 0 x x x x x x x (8-BIT WORD ORGANIZATION) ERASE 1 11 ERAL 1 00 1 0 x x x x x x x x x -- (RDY/BSY) 14 EWDS 1 00 0 0 x x x x x x x x x -- High-Z 14 EWEN 1 00 1 1 x x x x x x x x x -- High-Z 14 READ 1 10 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 -- D7-D0 22 WRITE 1 01 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 D7-D0 (RDY/BSY) 22 WRAL 1 00 D7-D0 (RDY/BSY) 22 (c) 2007 Microchip Technology Inc. A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 0 1 x x x x x x x x x DS21929D-page 9 93XX46X/56X/66X/76X/86X 3.0 FUNCTIONAL DESCRIPTION When the ORG pin is connected to VCC, the (x16) organization is selected. When it is connected to ground, the (x8) organization is selected. Instructions, addresses and write data are clocked into the DI pin on the rising edge of the clock (CLK). The DO pin is normally held in a High-Z state except when reading data from the device, or when checking the Ready/Busy status during a programming operation. The Ready/Busy status can be verified during an Erase/Write operation by polling the DO pin; DO low indicates that programming is still in progress, while DO high indicates the device is ready. DO will enter the High-Z state on the falling edge of CS. 3.1 Start Condition The Start bit is detected by the device if CS and DI are both high with respect to the positive edge of CLK for the first time. Before a Start condition is detected, CS, CLK and DI may change in any combination (except to that of a Start condition), without resulting in any device operation (Read, Write, Erase, EWEN, EWDS, ERAL or WRAL). As soon as CS is high, the device is no longer in Standby mode. An instruction following a Start condition will only be executed if the required opcode, address and data bits for any particular instruction are clocked in. Note: 3.2 When preparing to transmit an instruction, either the CLK or DI signal levels must be at a logic low as CS is toggled active high. 3.3 Data Protection All modes of operation are inhibited when VCC is below a typical voltage of 1.5V for `93AAXX' and `93LCXX' devices or 3.8V for `93CXX' devices. The EWEN and EWDS commands give additional protection against accidentally programming during normal operation. Note: For added protection, an EWDS command should be performed after every write operation and an external 10 k pull-down protection resistor should be added to the CS pin. After power-up, the device is automatically in the EWDS mode. Therefore, an EWEN instruction must be performed before the initial ERASE or WRITE instruction can be executed. Note: To prevent accidental writes to the array in the 93XX76C/86C devices, set the PE pin to a logic low. Block Diagram VCC VSS I/O Control Logic HV Generator Memory Control Logic X EEPROM Array Dec Byte Latches Data In/Data Out (DI/DO) It is possible to connect the Data In and Data Out pins together. However, with this configuration it is possible for a "bus conflict" to occur during the "dummy zero" that precedes the read operation, if A0 is a logic high level. Under such a condition the voltage level seen at Data Out is undefined and will depend upon the relative impedances of Data Out and the signal source driving A0. The higher the current sourcing capability of the driver, the higher the voltage at the Data Out pin. In order to limit this current, a resistor should be connected between DI and DO. DS21929D-page 10 Y Decoder DI DO CS CLK ORG(1) PE(2) Sense Amp. R/W Control Note 1: ORG pin: Only on 93XX46C/56C/66C/76C/86C. 2: PE pin: Only on 93XX76C/86C. (c) 2007 Microchip Technology Inc. 93XX46X/56X/66X/76X/86X 3.4 ERASE The DO pin indicates the Ready/Busy status of the device if CS is brought high after a minimum of 250 ns low (TCSL). DO at logical `0' indicates that programming is still in progress. DO at logical `1' indicates that the register at the specified address has been erased and the device is ready for another instruction. The ERASE instruction forces all data bits of the specified address to the logical `1' state. CS is brought low following the loading of the last address bit. This falling edge of the CS pin initiates the self-timed programming cycle, except on `93CXX' devices where the rising edge of CLK before the last address bit initiates the write cycle. FIGURE 3-1: Note: After the Erase cycle is complete, issuing a Start bit and then taking CS low will clear the Ready/Busy status from DO. ERASE TIMING FOR 93AAXX AND 93LCXX DEVICES TCSL Check Status CS CLK 1 DI 1 1 AN AN-1 AN-2 *** A0 TSV DO High-Z BUSY TCZ Ready High-Z TWC FIGURE 3-2: ERASE TIMING FOR 93CXX DEVICES TCSL Check Status CS CLK 1 DI 1 1 AN AN-1 AN-2 *** A0 TSV DO High-Z Busy TCZ Ready High-Z TWC (c) 2007 Microchip Technology Inc. DS21929D-page 11 93XX46X/56X/66X/76X/86X 3.5 ERASE ALL (ERAL) The DO pin indicates the Ready/Busy status of the device, if CS is brought high after a minimum of 250 ns low (TCSL). The Erase All (ERAL) instruction will erase the entire memory array to the logical `1' state. The ERAL cycle is identical to the Erase cycle, except for the different opcode. The ERAL cycle is completely self-timed and commences at the falling edge of the CS, except on `93CXX' devices where the rising edge of CLK before the last data bit initiates the write cycle. Clocking of the CLK pin is not necessary after the device has entered the ERAL cycle. FIGURE 3-3: VCC must be 4.5V for proper operation of ERAL. Note: After the ERAL command is complete, issuing a Start bit and then taking CS low will clear the Ready/Busy status from DO. ERAL TIMING FOR 93AAXX AND 93LCXX DEVICES TCSL Check Status CS CLK 1 DI 0 0 1 0 X *** X TSV DO High-Z TCZ Busy Ready High-Z TEC Vcc must be 4.5V for proper operation of ERAL. FIGURE 3-4: ERAL TIMING FOR 93CXX DEVICES TCSL CS Check Status CLK 1 DI 0 0 1 0 X *** X TSV DO High-Z Busy TCZ Ready High-Z TEC DS21929D-page 12 (c) 2007 Microchip Technology Inc. 93XX46X/56X/66X/76X/86X 3.6 ERASE/WRITE DISABLE And ENABLE (EWDS/EWEN) The 93XX series devices power-up in the Erase/Write Disable (EWDS) state. All programming modes must be preceded by an Erase/Write Enable (EWEN) instruction. Once the EWEN instruction is executed, programming remains enabled until an EWDS instruction is executed or VCC is removed from the device. To protect against accidental data disturbance, the EWDS instruction can be used to disable all Erase/Write functions and should follow all programming operations. Execution of a READ instruction is independent of both the EWEN and EWDS instructions. FIGURE 3-5: EWDS TIMING TCSL CS CLK DI 1 FIGURE 3-6: 0 0 0 0 x *** x EWEN TIMING TCSL CS CLK DI 1 0 (c) 2007 Microchip Technology Inc. 0 1 1 x *** x DS21929D-page 13 93XX46X/56X/66X/76X/86X 3.7 READ The READ instruction outputs the serial data of the addressed memory location on the DO pin. A dummy zero bit precedes the 8-bit (If ORG pin is low or A-version devices) or 16-bit (If ORG pin is high or B-version devices) output string. The output data bits will toggle on the rising edge of the CLK and are stable after the specified time delay (TPD). Sequential read is possible when CS is held high. The memory data will automatically cycle to the next register and output sequentially. FIGURE 3-7: READ TIMING CS CLK 1 DI DO High-Z DS21929D-page 14 1 0 An *** A0 0 Dx *** D0 Dx *** D0 Dx *** D0 (c) 2007 Microchip Technology Inc. 93XX46X/56X/66X/76X/86X 3.8 WRITE The DO pin indicates the Ready/Busy status of the device, if CS is brought high after a minimum of 250 ns low (TCSL). DO at logical `0' indicates that programming is still in progress. DO at logical `1' indicates that the register at the specified address has been written with the data specified and the device is ready for another instruction. The WRITE instruction is followed by 8 bits (If ORG is low or A-version devices) or 16 bits (If ORG pin is high or B-version devices) of data which are written into the specified address. For 93AAXX and 93LCXX devices, after the last data bit is clocked into DI, the falling edge of CS initiates the self-timed auto-erase and programming cycle. For 93CXX devices, the self-timed autoerase and programming cycle is initiated by the rising edge of CLK on the last data bit. FIGURE 3-8: Note: For devices with PE functionality such as the 93XX76C or 93XX86C, the write sequence requires a logic high signal on the PE pin prior to the rising edge of clock on the last data bit. Note: After the Write cycle is complete, issuing a Start bit and then taking CS low will clear the Ready/Busy status from DO. WRITE TIMING FOR 93AAXX AND 93LCXX DEVICES TCSL CS CLK DI 1 0 1 An *** A0 Dx *** D0 TSV High-Z DO Busy TCZ Ready High-Z Twc FIGURE 3-9: WRITE TIMING FOR 93CXX DEVICES TCSL CS CLK DI 1 0 1 An *** A0 Dx *** D0 TSV DO High-Z Busy TCZ Ready High-Z Twc (c) 2007 Microchip Technology Inc. DS21929D-page 15 93XX46X/56X/66X/76X/86X 3.9 WRITE ALL (WRAL) The DO pin indicates the Ready/Busy status of the device if CS is brought high after a minimum of 250 ns low (TCSL). The Write All (WRAL) instruction will write the entire memory array with the data specified in the command. For 93AAXX and 93LCXX devices, after the last data bit is clocked into DI, the falling edge of CS initiates the self-timed auto-erase and programming cycle. For 93CXX devices, the self-timed auto-erase and programming cycle is initiated by the rising edge of CLK on the last data bit. Clocking of the CLK pin is not necessary after the device has entered the WRAL cycle. The WRAL command does include an automatic ERAL cycle for the device. Therefore, the WRAL instruction does not require an ERAL instruction, but the chip must be in the EWEN status. FIGURE 3-10: VCC must be 4.5V for proper operation of WRAL. Note: For devices with PE functionality such as the 93XX76C or 93XX86C, the write sequence requires a logic high signal on the PE pin prior to the rising edge of clock on the last data bit. Note: After the Write All cycle is complete, issuing a Start bit and then taking CS low will clear the Ready/Busy status from DO. WRAL TIMING FOR 93AAXX AND 93LCXX DEVICES TCSL CS CLK DI 1 0 0 0 1 X *** x Dx *** D0 TSV High-Z DO Busy TCZ Ready HIGH-Z TWL VCC must be 4.5V for proper operation of WRAL. FIGURE 3-11: WRAL TIMING FOR 93CXX DEVICES TCSL CS CLK DI 1 0 0 0 1 X *** x Dx *** D0 TSV DO High-Z Busy TCZ Ready HIGH-Z TWL DS21929D-page 16 (c) 2007 Microchip Technology Inc. 93XX46X/56X/66X/76X/86X 4.0 PIN DESCRIPTIONS TABLE 4-1: PIN DESCRIPTIONS Name SOIC/PDIP/MSOP/ TSSOP/DFN SOT-23 CS 1 5 Chip Select CLK 2 4 Serial Clock DI 3 3 Data In DO 4 1 Data Out VSS 5 2 Ground 6 N/A 7 N/A 8 6 ORG NC(1) PE NC(1) VCC Function Organization (93XX46C/56C/66C/76C/86C) No connect on 93XXA/B devices Program Enable (93XX76C/86C) No connect on 93XXA/B devices Power Supply Note 1: With no internal connection, logic levels on NC pins are "don't cares." 4.1 Chip Select (CS) A high level selects the device; a low level deselects the device and forces it into Standby mode. However, a programming cycle which is already in progress will be completed, regardless of the Chip Select (CS) input signal. If CS is brought low during a program cycle, the device will go into Standby mode as soon as the programming cycle is completed. After detection of a Start condition the specified number of clock cycles (respectively low-to-high transitions of CLK) must be provided. These clock cycles are required to clock in all required opcode, address and data bits before an instruction is executed. CLK and DI then become "don't care" inputs waiting for a new Start condition to be detected. 4.3 Data In (DI) CS must be low for 250 ns minimum (TCSL) between consecutive instructions. If CS is low, the internal control logic is held in a Reset status. Data In (DI) is used to clock in a Start bit, opcode, address and data synchronously with the CLK input. 4.2 4.4 Serial Clock (CLK) The Serial Clock is used to synchronize the communication between a master device and the 93XX series device. Opcodes, address and data bits are clocked in on the positive edge of CLK. Data bits are also clocked out on the positive edge of CLK. CLK can be stopped anywhere in the transmission sequence (at high or low level) and can be continued anytime with respect to Clock High Time (TCKH) and Clock Low Time (TCKL). This gives the controlling master freedom in preparing opcode, address and data. CLK is a "don't care" if CS is low (device deselected). If CS is high, but the Start condition has not been detected (DI = 0), any number of clock cycles can be received by the device without changing its status (i.e., waiting for a Start condition). CLK cycles are not required during the self-timed Write (i.e., auto Erase/Write) cycle. (c) 2007 Microchip Technology Inc. Data Out (DO) Data Out (DO) is used in the Read mode to output data synchronously with the CLK input (TPD after the positive edge of CLK). This pin also provides Ready/Busy status information during Erase and Write cycles. Ready/Busy status information is available on the DO pin if CS is brought high after being low for minimum Chip Select Low Time (TCSL) and an erase or write operation has been initiated. The Status signal is not available on DO, if CS is held low during the entire Erase or Write cycle. In this case, DO is in the High-Z mode. If status is checked after the Erase/Write cycle, the data line will be high to indicate the device is ready. Note: After the Read cycle is complete, issuing a Start bit and then taking CS low will clear the Ready/Busy status from DO. DS21929D-page 17 93XX46X/56X/66X/76X/86X 4.5 Organization (ORG) 4.6 When the ORG pin is connected to VCC or Logic HI, the (x16) memory organization is selected. When the ORG pin is tied to VSS or Logic LO, the (x8) memory organization is selected. For proper operation, ORG must be tied to a valid logic level. A logic level on the PE pin will enable or disable the ability to write data to the memory array in only the 8-lead 93XX76C and 93XX86C devices. For all other devices the PE function is not present and the PE pin is a no connect. When driving the PE pin to a logic High, the device can be programmed, but when the PE pin is driven Low, programming is inhibited. This pin is used in parallel with the EWEN/EWDS latch to protect the memory array from inadvertent writes, as shown in Table 4-2. For devices without the ORG functionality, there is no internal connection to the ORG pin. In these devices the functionality has been set at the factory to support a single word size. `A' series devices - x8 organization In either the 93XX76C or 93XX86C devices, the PE pin must be tied to a specific logic level and cannot be floated. In all other devices without the PE function, the PE pin has no internal connections and programming is always enabled. `B' series devices - x16 organization TABLE 4-2: Program Enable (PE) WRITE PROTECTION SCHEME EWEN/EWDS Latch PE Pin* Array WRITE Enabled 1 Yes Disabled 1 No Enabled 0 No Disabled 0 No * PE pin level does not alter the state of the EWEN/EWDS latch. Note: For devices with PE functionality such as 93XX76C or 93XX86C, the write sequence requires a logic high signal on the PE pin prior to the rising edge of clock on the last data bit. DS21929D-page 18 (c) 2007 Microchip Technology Inc. 93XX46X/56X/66X/76X/86X APPENDIX A: REVISION HISTORY Revision A Original release of document. Combined all the 93-Series Microwire Serial EEPROM device data sheets. Revision B Revised 2x3 (MC) DFN package drawing. Revision C Correction to Table 2-6, 93XX76A (EWDS). Revision D (03/2007) Revised Description; Delete Pb-free notes; Replaced Package Drawings; Revised Product ID System. (c) 2007 Microchip Technology Inc. DS21929D-page 19 93XX46X/56X/66X/76X/86X 5.0 PACKAGING INFORMATION 5.1 Package Marking Information Example: Pb-free 8-Lead PDIP 93LC46A I/P e3 IL7 0528 XXXXXXXX TXXXXNNN YYWW 3-Wire 8-Lead PDIP Package Marking Part Line 1 Marking Part Line 1 Marking Part Line 1 Marking 93AA46A 93AA46A 93LC46A 93LC46A 93C46A 93C46A 93AA46B 93AA46B 93LC46B 93LC46B 93C46B 93C46B 93AA46C 93AA46C 93LC46C 93LC46C 93C46C 93C46C 93AA56A 93AA56A 93LC56A 93LC56A 93C56A 93C56A 93AA56B 93AA56B 93LC56B 93LC56B 93C56B 93C56B 93AA56C 93AA56C 93LC56C 93LC56C 93C56C 93C56C 93AA66A 93AA66A 93LC66A 93LC66A 93C66A 93C66A 93AA66B 93AA66B 93LC66B 93LC66B 93C66B 93C66B 93AA66C 93AA66C 93LC66C 93LC66C 93C66C 93C66C 93AA76A 93AA76A 93LC76A 93LC76A 93C76A 93C76A 93AA76B 93AA76B 93LC76B 93LC76B 93C76B 93C76B 93AA76C 93AA76C 93LC76C 93LC76C 93C76C 93C76C 93AA86A 93AA86A 93LC86A 93LC86A 93C86A 93C86A 93AA86B 93AA86B 93LC86B 93LC86B 93C86B 93C86B 93AA86C 93LC86C 93LC86C 93C86C 93C86C 93AA86C Note: Temperature range on second line. Legend: XX...X T Y YY WW NNN e3 Part number or part number code Temperature (I, E) Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week `01') Alphanumeric traceability code (2 characters for small packages) Pb-free JEDEC designator for Matte Tin (Sn) Note: For very small packages with no room for the Pb-free JEDEC designator e3 , the marking will only appear on the outer carton or reel label. Note: In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. DS21929D-page 20 (c) 2007 Microchip Technology Inc. 93XX46X/56X/66X/76X/86X Example: Pb-free 8-Lead SOIC 93LC46AI SN e3 0528 1L7 XXXXXXXT XXXXYYWW NNN 3-Wire 8-Lead SOIC (SN) Package Marking Part Line 1 Marking 93AA46A Part 93AA46AT 93LC46A 93AA46B 93AA46BT 93AA46C 93AA46CT 93AA56A 93AA56AT 93AA56B 93AA56BT 93AA56C 93AA66A Line 1 Marking Part Line 1 Marking 93LC46AT 93C46A 93LC46B 93LC46BT 93C46B 93C46BT 93LC46C 93LC46CT 93C46C 93C46CT 93LC56A 93LC56AT 93C56A 93C56AT 93LC56B 93LC56BT 93C56B 93C56BT 93AA56CT 93LC56C 93LC56CT 93C56C 93C56CT 93AA66AT 93LC66A 93LC66AT 93C66A 93C66AT 93AA66B 93AA66BT 93LC66B 93LC66BT 93C66B 93C66BT 93AA66C 93AA66CT 93LC66C 93LC66CT 93C66C 93C66CT 93AA76A 93AA76AT 93LC76A 93LC76AT 93C76A 93C76AT 93AA76B 93AA76BT 93LC76B 93LC76BT 93C76B 93C76BT 93AA76C 93AA76CT 93LC76C 93LC76CT 93C76C 93C76CT 93AA86A 93AA86AT 93LC86A 93LC86AT 93C86A 93C86AT 93AA86B 93AA86BT 93LC86B 93LC86BT 93C86B 93C86BT 93AA86C 93AA86CT 93LC86C 93LC86CT 93C86C 93C86CT Note: 93C46AT T = Temperature Range: I = Industrial, E = Extended Legend: XX...X T Y YY WW NNN e3 Part number or part number code Temperature (I, E) Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week `01') Alphanumeric traceability code (2 characters for small packages) Pb-free JEDEC designator for Matte Tin (Sn) Note: For very small packages with no room for the Pb-free JEDEC designator e3 , the marking will only appear on the outer carton or reel label. Note: In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. (c) 2007 Microchip Technology Inc. DS21929D-page 21 93XX46X/56X/66X/76X/86X Example: 8-Lead 2x3 DFN 304 506 L7 XXX YWW NN 3-Wire 2x3 DFN Package Marking Industrial Line 1 Marking E-Temp Line 1 Marking 93AA46A 301 302 93LC46A 304 305 93C46A 307 308 93AA46B 311 312 93LC46B 314 315 93C46B 317 318 93AA46C 321 322 93LC46C 324 325 93C46C 327 328 93AA56A 331 332 93LC56A 334 335 93C56A 337 338 93AA56B 341 342 93LC56B 344 345 93C56B 347 348 93AA56C 351 352 93LC56C 354 355 93C56C 357 358 93AA66A 361 362 93LC66A 364 365 93C66A 367 368 93AA66B 371 372 93LC66B 374 375 93C66B 377 378 93AA66C 381 382 93LC66C 384 385 93C66C 387 388 93AA76C 3B1 3B2 93LC76C 3B4 3B5 93C76C 3B7 3B8 93AA86C 3E1 3E2 93LC86C 3E4 3E5 93C86C 3E7 3E8 Part Legend: XX...X T Y YY WW NNN e3 Part Industrial Line 1 Marking E-Temp Line 1 Marking Part Industrial Line 1 Marking Part number or part number code Temperature (I, E) Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week `01') Alphanumeric traceability code (2 characters for small packages) Pb-free JEDEC designator for Matte Tin (Sn) Note: For very small packages with no room for the Pb-free JEDEC designator e3 , the marking will only appear on the outer carton or reel label. Note: In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. DS21929D-page 22 E-Temp Line 1 Marking (c) 2007 Microchip Technology Inc. 93XX46X/56X/66X/76X/86X Example: 6-Lead SOT-23 1EL7 XXNN 3-Wire 6-Lead SOT-23 Package Marking Part Industrial Line 1 Marking E-Temp Line 1 Marking 93AA46A 1BNN 1CNN 93LC46A 1ENN 1FNN 93C46A 1HNN 1JNN 93AA46B 1LNN 1MNN 93LC46B 1PNN 1RNN 93C46B 1TNN 1UNN 93AA56A 2BNN 2CNN 93LC56A 2ENN 2FNN 93C56A 2HNN 2JNN 93AA56B 2LNN 2MNN 93LC56B 2PNN 2RNN 93C56B 2TNN 2UNN 93AA66A 3BNN 3CNN 93LC66A 3ENN 3FNN 93C66A 3HNN 3JNN 93AA66B 3LNN 3MNN 93LC66B 3PNN 3RNN 93C66B 3TNN 3UNN 93AA76A 4BNN 4CNN 93LC76A 4ENN 4FNN 93C76A 4HNN 4JNN 93AA76B 4LNN 4MNN 93LC76B 4PNN 4RNN 93C76B 4TNN 4UNN 93AA86A 5BNN 5CNN 93LC86A 5ENN 5FNN 93C86A 5HNN 5JNN 93AA86B 5LNN 5MNN 93LC86B 5PNN 5RNN 93C86B 5TNN 5UNN Legend: XX...X T Y YY WW NNN e3 Part Industrial Line 1 Marking E-Temp Line 1 Marking Part Industrial Line 1 Marking Part number or part number code Temperature (I, E) Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week `01') Alphanumeric traceability code (2 characters for small packages) Pb-free JEDEC designator for Matte Tin (Sn) Note: For very small packages with no room for the Pb-free JEDEC designator e3 , the marking will only appear on the outer carton or reel label. Note: In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. (c) 2007 Microchip Technology Inc. E-Temp Line 1 Marking DS21929D-page 23 93XX46X/56X/66X/76X/86X 8-Lead MSOP (150 mil) Example: 3L46AI 5281L7 XXXXXXT YWWNNN 3-Wire 8-Lead MSOP Package Marking Part Line 1 Marking 93AA46A 3A46AT Part 93LC46A Line 1 Marking 3L46AT Part Line 1 Marking 93C46A 3C46AT 93AA46B 3A46BT 93LC46B 3L46BT 93C46B 3C46BT 93AA46C 3A46CT 93LC46C 3L46CT 93C46C 3C46CT 93AA56A 3A56AT 93LC56A 3L56AT 93C56A 3C56AT 93AA56B 3A56BT 93LC56B 3L56BT 93C56B 3C56BT 93AA56C 3A56CT 93LC56C 3L56CT 93C56C 3C56CT 93AA66A 3A66AT 93LC66A 3L66AT 93C66A 3C66AT 93AA66B 3A66BT 93LC66B 3L66BT 93C66B 3C66BT 93AA66C 3A66CT 93LC66C 3L66CT 93C66C 3C66CT 93AA76A 3A76AT 93LC76A 3L76AT 93C76A 3C76AT 93AA76B 3A76BT 93LC76B 3L76BT 93C76B 3C76BT 93AA76C 3A76CT 93LC76C 3L76CT 93C76C 3C76CT 93AA86A 3A86AT 93LC86A 3L86AT 93C86A 3C86AT 93AA86B 3A86BT 93LC86B 3L86BT 93C86B 3C86BT 93AA86C 3A86CT 93LC86C 3L86CT 93C86C 3C86CT Note: T = Temperature Range: I = Industrial, E = Extended Legend: XX...X T Y YY WW NNN e3 Part number or part number code Temperature (I, E) Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week `01') Alphanumeric traceability code (2 characters for small packages) Pb-free JEDEC designator for Matte Tin (Sn) Note: For very small packages with no room for the Pb-free JEDEC designator e3 , the marking will only appear on the outer carton or reel label. Note: In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. DS21929D-page 24 (c) 2007 Microchip Technology Inc. 93XX46X/56X/66X/76X/86X Example: 8-Lead TSSOP L46A I528 1L7 XXXX TYWW NNN 3-Wire 8-Lead TSSOP Package Marking Part Line 1 Marking Part Line 1 Marking Part Line 1 Marking 93AA46A A46A 93LC46A L46A 93C46A C46A 93AA46B A46B 93LC46B L46B 93C46B C46B 93AA46C A46C 93LC46C L46C 93C46C C46C 93AA56A A56A 93LC56A L56A 93C56A C56A 93AA56B A56B 93LC56B L56B 93C56B C56B 93AA56C A56C 93LC56C L56C 93C56C C56C 93AA66A A66A 93LC66A L66A 93C66A C66A 93AA66B A66B 93LC66B L66B 93C66B C66B 93AA66C A66C 93LC66C L66C 93C66C C66C 93AA76A A76A 93LC76A L76A 93C76A C76A 93AA76B A76B 93LC76B L76B 93C76B C76B 93AA76C A76C 93LC76C L76C 93C76C C76C 93AA86A A86A 93LC86A L86A 93C86A C86A 93AA86B A86B 93LC86B L86B 93C86B C86B A86C 93LC86C L86C 93C86C C86C 93AA86C Note: Temperature range on second line. Legend: XX...X T Y YY WW NNN e3 Part number or part number code Temperature (I, E) Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week `01') Alphanumeric traceability code (2 characters for small packages) Pb-free JEDEC designator for Matte Tin (Sn) Note: For very small packages with no room for the Pb-free JEDEC designator e3 , the marking will only appear on the outer carton or reel label. Note: In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. (c) 2007 Microchip Technology Inc. DS21929D-page 25 93XX46X/56X/66X/76X/86X 8-Lead Plastic Dual In-Line (P or PA) - 300 mil Body [PDIP] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging N NOTE 1 E1 1 3 2 D E A2 A L A1 c e eB b1 b Units Dimension Limits Number of Pins INCHES MIN N NOM MAX 8 Pitch e Top to Seating Plane A - - .210 Molded Package Thickness A2 .115 .130 .195 Base to Seating Plane A1 .015 - - Shoulder to Shoulder Width E .290 .310 .325 Molded Package Width E1 .240 .250 .280 Overall Length D .348 .365 .400 Tip to Seating Plane L .115 .130 .150 Lead Thickness c .008 .010 .015 b1 .040 .060 .070 b .014 .018 .022 eB - - Upper Lead Width Lower Lead Width Overall Row Spacing .100 BSC .430 Notes: 1. Pin 1 visual index feature may vary, but must be located with the hatched area. 2. Significant Characteristic. 3. Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" per side. 4. Dimensioning and tolerancing per ASME Y14.5M. BSC: Basic Dimension. Theoretically exact value shown without tolerances. Microchip Technology Drawing C04-018B DS21929D-page 26 (c) 2007 Microchip Technology Inc. 93XX46X/56X/66X/76X/86X 8-Lead Plastic Small Outline (SN or OA) - Narrow, 3.90 mm Body [SOIC] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging D e N E E1 NOTE 1 1 2 3 h b h A2 A c L A1 L1 Units Dimension Limits Number of Pins MILLIMETERS MIN N NOM MAX 8 Pitch e Overall Height A - 1.27 BSC - Molded Package Thickness A2 1.25 - - Standoff A1 0.10 - 0.25 Overall Width E Molded Package Width E1 3.90 BSC Overall Length D 4.90 BSC 1.75 6.00 BSC Chamfer (optional) h 0.25 - 0.50 Foot Length L 0.40 - 1.27 Footprint L1 1.04 REF Foot Angle 0 - 8 Lead Thickness c 0.17 - 0.25 Lead Width b 0.31 - 0.51 Mold Draft Angle Top 5 - 15 Mold Draft Angle Bottom 5 - 15 Notes: 1. Pin 1 visual index feature may vary, but must be located within the hatched area. 2. Significant Characteristic. 3. Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.15 mm per side. 4. Dimensioning and tolerancing per ASME Y14.5M. BSC: Basic Dimension. Theoretically exact value shown without tolerances. REF: Reference Dimension, usually without tolerance, for information purposes only. Microchip Technology Drawing C04-057B (c) 2007 Microchip Technology Inc. DS21929D-page 27 93XX46X/56X/66X/76X/86X 8-Lead Plastic Dual Flat, No Lead Package (MC) - 2x3x0.9 mm Body [DFN] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging D e b N N L K E2 E EXPOSED PAD NOTE 1 2 1 NOTE 1 1 2 D2 BOTTOM VIEW TOP VIEW A A3 A1 NOTE 2 Units Dimension Limits Number of Pins MILLIMETERS MIN N NOM MAX 8 Pitch e Overall Height A 0.80 0.90 1.00 Standoff A1 0.00 0.02 0.05 Contact Thickness A3 0.20 REF Overall Length D 2.00 BSC Overall Width E Exposed Pad Length D2 1.30 - Exposed Pad Width E2 1.50 - 1.90 b 0.18 0.25 0.30 Contact Length L 0.30 0.40 0.50 Contact-to-Exposed Pad K 0.20 - - Contact Width 0.50 BSC 3.00 BSC 1.75 Notes: 1. Pin 1 visual index feature may vary, but must be located within the hatched area. 2. Package may have one or more exposed tie bars at ends. 3. Package is saw singulated. 4. Dimensioning and tolerancing per ASME Y14.5M. BSC: Basic Dimension. Theoretically exact value shown without tolerances. REF: Reference Dimension, usually without tolerance, for information purposes only. Microchip Technology Drawing C04-123B DS21929D-page 28 (c) 2007 Microchip Technology Inc. 93XX46X/56X/66X/76X/86X 6-Lead Plastic Small Outline Transistor (CH or OT) [SOT-23] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging b 4 N E E1 PIN 1 ID BY LASER MARK 1 2 3 e e1 D A A2 c L A1 L1 Units Dimension Limits Number of Pins MILLIMETERS MIN N NOM MAX 6 Pitch e 0.95 BSC Outside Lead Pitch e1 1.90 BSC Overall Height A 0.90 - Molded Package Thickness A2 0.89 - 1.45 1.30 Standoff A1 0.00 - 0.15 Overall Width E 2.20 - 3.20 Molded Package Width E1 1.30 - 1.80 Overall Length D 2.70 - 3.10 Foot Length L 0.10 - 0.60 Footprint L1 0.35 - 0.80 Foot Angle 0 - 30 Lead Thickness c 0.08 - 0.26 Lead Width b 0.20 - 0.51 Notes: 1. Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.127 mm per side. 2. Dimensioning and tolerancing per ASME Y14.5M. BSC: Basic Dimension. Theoretically exact value shown without tolerances. Microchip Technology Drawing C04-028B (c) 2007 Microchip Technology Inc. DS21929D-page 29 93XX46X/56X/66X/76X/86X 8-Lead Plastic Micro Small Outline Package (MS or UA) [MSOP] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging D N E E1 NOTE 1 1 2 e b A2 A c L L1 A1 Units Dimension Limits Number of Pins MILLIMETERS MIN N NOM MAX 8 Pitch e Overall Height A - 0.65 BSC - Molded Package Thickness A2 0.75 0.85 0.95 Standoff A1 0.00 - 0.15 Overall Width E Molded Package Width E1 3.00 BSC Overall Length D 3.00 BSC Foot Length L Footprint L1 1.10 4.90 BSC 0.40 0.60 0.80 0.95 REF Foot Angle 0 - 8 Lead Thickness c 0.08 - 0.23 Lead Width b 0.22 - 0.40 Notes: 1. Pin 1 visual index feature may vary, but must be located within the hatched area. 2. Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.15 mm per side. 3. Dimensioning and tolerancing per ASME Y14.5M. BSC: Basic Dimension. Theoretically exact value shown without tolerances. REF: Reference Dimension, usually without tolerance, for information purposes only. Microchip Technology Drawing C04-111B DS21929D-page 30 (c) 2007 Microchip Technology Inc. 93XX46X/56X/66X/76X/86X 8-Lead Plastic Thin Shrink Small Outline (ST) - 4.4 mm Body [TSSOP] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging D N E E1 NOTE 1 1 2 b e c A A2 A1 L L1 Units Dimension Limits Number of Pins MILLIMETERS MIN N NOM MAX 8 Pitch e Overall Height A - 0.65 BSC - Molded Package Thickness A2 0.80 1.00 1.05 Standoff A1 0.05 - 0.15 1.20 Overall Width E Molded Package Width E1 4.30 6.40 BSC 4.40 Molded Package Length D 2.90 3.00 3.10 Foot Length L 0.45 0.60 0.75 Footprint L1 4.50 1.00 REF Foot Angle 0 - 8 Lead Thickness c 0.09 - 0.20 Lead Width b 0.19 - 0.30 Notes: 1. Pin 1 visual index feature may vary, but must be located within the hatched area. 2. Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.15 mm per side. 3. Dimensioning and tolerancing per ASME Y14.5M. BSC: Basic Dimension. Theoretically exact value shown without tolerances. REF: Reference Dimension, usually without tolerance, for information purposes only. Microchip Technology Drawing C04-086B (c) 2007 Microchip Technology Inc. DS21929D-page 31 93XX46X/56X/66X/76X/86X NOTES: DS21929D-page 32 (c) 2007 Microchip Technology Inc. 93XX46X/56X/66X/76X/86X THE MICROCHIP WEB SITE CUSTOMER SUPPORT Microchip provides online support via our WWW site at www.microchip.com. This web site is used as a means to make files and information easily available to customers. Accessible by using your favorite Internet browser, the web site contains the following information: Users of Microchip products can receive assistance through several channels: * Product Support - Data sheets and errata, application notes and sample programs, design resources, user's guides and hardware support documents, latest software releases and archived software * General Technical Support - Frequently Asked Questions (FAQ), technical support requests, online discussion groups, Microchip consultant program member listing * Business of Microchip - Product selector and ordering guides, latest Microchip press releases, listing of seminars and events, listings of Microchip sales offices, distributors and factory representatives * * * * * Distributor or Representative Local Sales Office Field Application Engineer (FAE) Technical Support Development Systems Information Line Customers should contact their distributor, representative or field application engineer (FAE) for support. Local sales offices are also available to help customers. A listing of sales offices and locations is included in the back of this document. Technical support is available through the web site at: http://support.microchip.com CUSTOMER CHANGE NOTIFICATION SERVICE Microchip's customer notification service helps keep customers current on Microchip products. Subscribers will receive e-mail notification whenever there are changes, updates, revisions or errata related to a specified product family or development tool of interest. To register, access the Microchip web site at www.microchip.com, click on Customer Change Notification and follow the registration instructions. (c) 2007 Microchip Technology Inc. DS21929D-page 33 93XX46X/56X/66X/76X/86X READER RESPONSE It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip product. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our documentation can better serve you, please FAX your comments to the Technical Publications Manager at (480) 792-4150. Please list the following information, and use this outline to provide us with your comments about this document. To: Technical Publications Manager RE: Reader Response Total Pages Sent ________ From: Name Company Address City / State / ZIP / Country Telephone: (_______) _________ - _________ FAX: (______) _________ - _________ Application (optional): Would you like a reply? Y N Device: 93XX46X/56X/66X/76X/86X Literature Number: DS21929D Questions: 1. What are the best features of this document? 2. How does this document meet your hardware and software development needs? 3. Do you find the organization of this document easy to follow? If not, why? 4. What additions to the document do you think would enhance the structure and subject? 5. What deletions from the document could be made without affecting the overall usefulness? 6. Is there any incorrect or misleading information (what and where)? 7. How would you improve this document? DS21929D-page 34 (c) 2007 Microchip Technology Inc. 93XX46X/56X/66X/76X/86X PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. EEPROM Voltage Series Density Word Size Temp Range Tape & Reel Package 93 AA = 1.8V-5.5V LC = 2.5V-5.5V C = 4.5V-5.5V 46 = 1 Kbit 56 = 2 Kbit 66 = 4 Kbit 76 = 8 Kbit 86 = 16 Kbit A = x8 bit B = x16 bit C = Selectable Blank = Std Pkg T = Tape & Reel I = -40C to +85C E = -40C to +125C Examples: a) b) c) d) e) f) g) h) i) P = 8-Lead PDIP SN = 8-Lead SOIC (3.90 mm) MC = 8-Lead 2x3 DFN CH or OT = 6-Lead SOT-23 MS = 8-Lead MSOP ST = 8-Lead TSSOP 93AA46A-I/MS: 1K, 128x8 Serial EEPROM, Industrial Temperature, MSOP package, 1.8V 93AA46BT-I/OT: 1K, 64x16 Serial EEPROM, SOT-23 package, tape and reel, 1.8V 93AA46CT-I/MS: 1K, 128x8 or 64x16 Serial EEPROM, MSOP package, tape and reel, 1.8V 93AA46BX-I/SN: 1K, 128x8 Serial EEPROM, Industrial temperature, SOIC package (alternate pinout), tape and reel package, 1.8V 93LC66A-I/MS: 4K, 512x8 Serial EEPROM, MSOP package, 2.5V 93LC66BT-I/OT: 4K, 256x16 Serial EEPROM, SOT-23 package, tape and reel, 2.5V 93C86AT-I/OT: 16K, 2048x8 Serial EEPROM, SOT-23 package, tape and reel, 5.0V 93C86BT-I/OT: 16K, 1024x16 Serial EEPROM, SOT-23 package, tape and reel, 5.0V 93C86CT-I/MC: 16K, 2048x8 or 1024x16 Serial EEPROM, DFN Industrial temperature, tape and reel package, 5.0V (c) 2007 Microchip Technology Inc. DS21929D-page 35 93XX46X/56X/66X/76X/86X NOTES: DS21929D-page 36 (c) 2007 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: * Microchip products meet the specification contained in their particular Microchip Data Sheet. * Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. * There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip's Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. * Microchip is willing to work with the customer who is concerned about the integrity of their code. * Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as "unbreakable." Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip's code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer's risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, Accuron, dsPIC, KEELOQ, KEELOQ logo, microID, MPLAB, PIC, PICmicro, PICSTART, PRO MATE, PowerSmart, rfPIC, and SmartShunt are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. AmpLab, FilterLab, Linear Active Thermistor, Migratable Memory, MXDEV, MXLAB, PS logo, SEEVAL, SmartSensor and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Analog-for-the-Digital Age, Application Maestro, CodeGuard, dsPICDEM, dsPICDEM.net, dsPICworks, ECAN, ECONOMONITOR, FanSense, FlexROM, fuzzyLAB, In-Circuit Serial Programming, ICSP, ICEPIC, Mindi, MiWi, MPASM, MPLAB Certified logo, MPLIB, MPLINK, PICkit, PICDEM, PICDEM.net, PICLAB, PICtail, PowerCal, PowerInfo, PowerMate, PowerTool, REAL ICE, rfLAB, rfPICDEM, Select Mode, Smart Serial, SmartTel, Total Endurance, UNI/O, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. (c) 2007, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. Microchip received ISO/TS-16949:2002 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona, Gresham, Oregon and Mountain View, California. The Company's quality system processes and procedures are for its PIC(R) MCUs and dsPIC(R) DSCs, KEELOQ(R) code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip's quality system for the design and manufacture of development systems is ISO 9001:2000 certified. (c) 2007 Microchip Technology Inc. DS21929D-page 37 WORLDWIDE SALES AND SERVICE AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://support.microchip.com Web Address: www.microchip.com Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Habour City, Kowloon Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 India - Bangalore Tel: 91-80-4182-8400 Fax: 91-80-4182-8422 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 India - Pune Tel: 91-20-2566-1512 Fax: 91-20-2566-1513 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Japan - Yokohama Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Farmington Hills, MI Tel: 248-538-2250 Fax: 248-538-2260 Kokomo Kokomo, IN Tel: 765-864-8360 Fax: 765-864-8387 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Santa Clara Santa Clara, CA Tel: 408-961-6444 Fax: 408-961-6445 Toronto Mississauga, Ontario, Canada Tel: 905-673-0699 Fax: 905-673-6509 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8528-2100 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 Korea - Gumi Tel: 82-54-473-4301 Fax: 82-54-473-4302 China - Fuzhou Tel: 86-591-8750-3506 Fax: 86-591-8750-3521 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 China - Hong Kong SAR Tel: 852-2401-1200 Fax: 852-2401-3431 Malaysia - Penang Tel: 60-4-646-8870 Fax: 60-4-646-5086 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 Taiwan - Hsin Chu Tel: 886-3-572-9526 Fax: 886-3-572-6459 China - Shenzhen Tel: 86-755-8203-2660 Fax: 86-755-8203-1760 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 China - Shunde Tel: 86-757-2839-5507 Fax: 86-757-2839-5571 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 UK - Wokingham Tel: 44-118-921-5869 Fax: 44-118-921-5820 China - Xian Tel: 86-29-8833-7250 Fax: 86-29-8833-7256 12/08/06 DS21929D-page 38 (c) 2007 Microchip Technology Inc.