2.0x1.25 mm INFRARED EMITTING DIODE Part Number: APT2012SF4C-PRV Features Description z 2.0mmx1.25mm SMD LED,0.75mm thickness. SF4 Made with Gallium Aluminum Arsenide Infrared Emit- z Mechanically and spectrally matched to the phototransistor. ting diodes. z Package: 2000pcs / reel. z Moisture sensitivity level : level 3. z RoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is 0.1(0.004") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAJ1371 REV NO: V.5B DATE: JAN/04/2017 PAGE: 1 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: W.Q.Zhong ERP: 1203008893 Selection Guide Part No. APT2012SF4C-PRV Emitting Color (Material) Po (mW/sr) [2] @ 20mA Lens Type Infrared (GaAlAs) Water Clear Viewing Angle [1] Min. Typ. 21/2 0.8 1.5 160 Notes: 1. 1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Radiant Intensity/ luminous flux: +/-15%. 3. Radiant intensity value is traceable to CIE127-2007 standards. Electrical / Optical Characteristics at TA=25C Parameter P/N Symbol Typ. Max. Units Test Conditions Forward Voltage [1] SF4 VF 1.3 1.6 V IF=20mA Reverse Current SF4 IR 10 uA VR = 5V Capacitance SF4 C 90 pF VF=0V;f=1MHz Peak Spectral Wavelength SF4 P 880 nm IF=20mA Spectral Bandwidth SF4 1/2 50 nm IF=20mA Notes: 1. Forward Voltage: +/-0.1V. 2. Wavelength value is traceable to CIE127-2007 standards. 3. Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25C Parameter Symbol Values Units Power dissipation PD 80 mW DC Forward Current IF 50 mA Peak Forward Current [1] iFS 1.2 A Reverse Voltage VR 5 V Operating Temperature TA -40 To +85 C TSTG -40 To +85 C Storage Temperature Notes: 1. 1/100 Duty Cycle, 10s Pulse Width. 2. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static electricity - Ref JEDEC/JESD625-A and JEDEC/J-STD-033. SPEC NO: DSAJ1371 REV NO: V.5B DATE: JAN/04/2017 PAGE: 2 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: W.Q.Zhong ERP: 1203008893 SF4 Relative Intensity (a. u.) 100% 80% Ta = 25 C 60% 40% 20% 0% 600 650 700 750 800 850 Wavelength (nm) 900 950 1000 1050 APT2012SF4C-PRV -15 Ta = 25 C 0 -30 15 30 -45 45 60 -60 75 -75 -90 1.0 0.5 0.0 0.5 90 1.0 SPEC NO: DSAJ1371 REV NO: V.5B DATE: JAN/04/2017 PAGE: 3 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: W.Q.Zhong ERP: 1203008893 APT2012SF4C-PRV Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: 0.1) Reel Dimension Tape Specifications (Units : mm) SPEC NO: DSAJ1371 REV NO: V.5B DATE: JAN/04/2017 PAGE: 4 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: W.Q.Zhong ERP: 1203008893 PACKING & LABEL SPECIFICATIONS APT2012SF4C-PRV Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAJ1371 REV NO: V.5B DATE: JAN/04/2017 PAGE: 5 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: W.Q.Zhong ERP: 1203008893 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Kingbright: APT2012SF4C-PRV