NL17SH125 Non-Inverting 3-State Buffer The NL17SH125 MiniGatet is an advanced high-speed CMOS non-inverting buffer in ultra-small footprint. The NL17SH125 requires the 3-state control input (OE) to be set High to place the output in the high impedance state. The NL17SH125 input structures provide protection when voltages up to 7.0 V are applied, regardless of the supply voltage. http://onsemi.com MARKING DIAGRAM Features High Speed: tPD = 3.8 ns (Typ) at VCC = 5.0 V Low Power Dissipation: ICC = 1.0 mA (Max) at TA = 25C SOT-953 CASE 527AE Power Down Protection Provided on Inputs Balanced Propagation Delays These are Pb-Free and Halide-Free Devices T M T * * * * * M 1 = Specific Device Code (Rotated 90) = Month Code PIN ASSIGNMENT IN A GND OE 5 1 VCC 2 4 3 1 IN A 2 GND 3 OE 4 OUT Y 5 VCC OUT Y FUNCTION TABLE Figure 1. Pinout (Top View) OE EN IN A OUT Y Input A Input OE Output Y L H X L L H L H Z Figure 2. Logic Symbol ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 4 of this data sheet. (c) Semiconductor Components Industries, LLC, 2012 September, 2012 - Rev. 0 1 Publication Order Number: NL17SH125/D NL17SH125 MAXIMUM RATINGS Symbol Parameter VCC DC Supply Voltage VIN DC Input Voltage VOUT DC Input Diode Current IOK DC Output Diode Current IOUT DC Output Source/Sink Current ICC DC Supply Current per Supply Pin IGND DC Ground Current per Ground Pin TSTG Storage Temperature Range Unit -0.5 to +7.0 V -0.5 to +7.0 V -0.5 to VCC + 0.5 V VIN < GND -20 mA VOUT < GND, VOUT > VCC 20 mA 12.5 mA 25 mA DC Output Voltage IIK Value 25 mA -65 to +150 C TL Lead Temperature, 1 mm from Case for 10 Seconds 260 C TJ Junction Temperature Under Bias +150 C MSL Moisture Sensitivity FR Flammability Rating VESD ILATCHUP Level 1 Oxygen Index: 28 to 34 ESD Withstand Voltage UL 94 V-0 @ 0.125 in Human Body Model (Note 2) Machine Model (Note 3) Charged Device Model (Note 4) Latchup Performance Above VCC and Below GND at 125C (Note 5) >3000 >150 N/A V 100 mA Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. Measured with minimum pad spacing on an FR4 board, using 10 mm-by-1 inch, 2-ounce copper trace with no air flow. 2. Tested to EIA/JESD22-A114-A. 3. Tested to EIA/JESD22-A115-A. 4. Tested to JESD22-C101-A. 5. Tested to EIA/JESD78. RECOMMENDED OPERATING CONDITIONS Symbol Characteristics Min Max Unit VCC Positive DC Supply Voltage 1.65 5.5 V VIN Digital Input Voltage 0.0 5.5 V Output Voltage 0.0 VCC V -55 +125 C 0 0 100 20 ns/V VOUT TA Dt / DV Operating Temperature Range Input Transition Rise or Fail Rate VCC = 3.3 V 0.3 V VCC = 5.0 V 0.5 V http://onsemi.com 2 NL17SH125 DC ELECTRICAL CHARACTERISTICS TA = 255C VCC Symbol VIH VIL VOH VOL Parameter Test Conditions High-Level Input Voltage Low-Level Input Voltage High-Level Output Voltage Low-Level Output Voltage TA v 855C (V) Min Typ Max Min 1.65 to 2.0 0.75 x VCC 0.75 x VCC 2.3 to 5.5 0.70 x VCC 0.70 x VCC Max *555C to 1255C Min Max V 1.65 to 2.0 0.25 x VCC 0.25 x VCC 0.25 x VCC 2.3 to 5.5 0.30 x VCC 0.30 x VCC 0.30 x VCC VIN = VIH or VIL IOH = -50 mA 2.0 3.0 4.5 1.9 2.9 4.4 VIN = VIH or VIL IOH = -4 mA IOH = -8 mA 3.0 4.5 2.58 3.94 VIN = VIH or VIL IOL = 50 mA 2.0 3.0 4.5 VIN = VIH or VIL IOL = 4 mA IOL = 8 mA 2.0 3.0 4.5 0.0 0.0 0.0 Unit 1.9 2.9 4.4 1.9 2.9 4.4 2.48 3.80 2.34 3.66 V V 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 3.0 4.5 0.36 0.36 0.44 0.44 0.52 0.52 V IIN Input Leakage Current 0 VIN 5.5 V 0 to 5.5 $0.1 $1.0 $1.0 mA ICC Quiescent Supply Current 0 VIN VCC 5.5 1.0 10 40 mA IOZ 3-State Leakage Current VIN = VIH or VIL VOUT = VCC or GND 0.0 $0.25 $2.5 $2.5 mA AC ELECTRICAL CHARACTERISTICS (Input tr = tf = 3.0 ns) Symbol tPLH, tPHL tPZL, tPZH tPLZ, tPHZ Parameter Propagation Delay, A to Y Output Enable Time, OE to Y Output Enable Time, OE to Y CIN Input Capacitance CPD Power Dissipation Capacitance (Note 6) VCC (V) TA = 255C Test Conditions Min TA v 855C *555C to 1255C Typ Max Min Max Max Unit 3.0 to 3.6 CL = 15 pF CL = 50 pF 5.6 8.1 8.0 11.5 1.0 1.0 9.5 13.0 12.0 16.0 ns 4.5 to 5.5 CL = 15 pF CL = 50 pF 3.8 5.3 5.5 7.5 1.0 1.0 6.5 8.5 8.5 10.5 3.0 to 3.6 CL = 15 pF CL = 50 pF 5.4 7.9 8.0 11.5 1.0 1.0 9.5 13.0 11.5 15.0 4.5 to 5.5 CL = 15 pF CL = 50 pF 3.6 5.1 5.1 7.1 1.0 1.0 6.0 8.0 7.5 9.5 3.0 to 3.6 CL = 15 pF CL = 50 pF 6.5 8.0 9.7 13.2 1.0 1.0 11.5 15.0 14.5 18.5 4.5 to 5.5 CL = 15 pF CL = 50 pF 4.8 7.0 6.8 8.8 1.0 1.0 8.0 10 10.0 12.0 5.5 10 10 10 5.0 11 Min ns ns pF pF 6. CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation: ICC(OPR) = CPD VCC fin + ICC. CPD is used to determine the no-load dynamic power consumption; PD = CPD VCC2 fin + ICC VCC. http://onsemi.com 3 NL17SH125 ORDERING INFORMATION Device NL17SH125P5T5G Package Shipping SOT-953 (Pb-Free) 8000 / Tape & Reel For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. A or B VCC 50% Y tPLH tPLZ 50% VCC Y tPZH tPHZ 50% VCC Figure 3. Switching Waveform HIGH IMPEDANCE VOL + 0.3V VOH - 0.3V 50% VCC Y HIGH IMPEDANCE Figure 4. TEST POINT TEST POINT 1 kW OUTPUT DEVICE UNDER TEST GND tPZL GND tPHL VCC 50% DEVICE UNDER TEST CL* *Includes all probe and jig capacitance. CL* Connect to VCC when testing tPLZ and tPZL. Connect to GND when testing tPHZ and tPZH. *Includes all probe and jig capacitance. Figure 5. Test Circuit Figure 6. Test Circuit INPUT Figure 7. Input Equivalent Circuit http://onsemi.com 4 NL17SH125 PACKAGE DIMENSIONS SOT-953 CASE 527AE ISSUE E X D Y PIN ONE INDICATOR 5 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF THE BASE MATERIAL. 4. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. A 4 HE E 1 2 3 DIM A b C D E e HE L L2 L3 C TOP VIEW SIDE VIEW e L 5X 5X L3 MILLIMETERS MIN NOM MAX 0.34 0.37 0.40 0.10 0.15 0.20 0.07 0.12 0.17 0.95 1.00 1.05 0.75 0.80 0.85 0.35 BSC 0.95 1.00 1.05 0.175 REF 0.05 0.10 0.15 --- --- 0.15 SOLDERING FOOTPRINT* 5X 0.35 5X 0.20 5X L2 5X BOTTOM VIEW b PACKAGE OUTLINE 0.08 X Y 1.20 1 0.35 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. MiniGate is a trademark of Semiconductor Components Industries, LLC (SCILLC). ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5817-1050 http://onsemi.com 5 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NL17SH125/D