CLASSIFICATION SUBJECT PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 1 of 53 DATE 11.07.2014 Specification for Production Applicant / Manufacturer Hardware Panasonic Industrial Devices Europe GmbH Zeppelinstrasse 19 21337 Luneburg Germany Applicant / Manufacturer Software Software Version Please refer to chapter 32 / 32.1 Information regarding Software Versions Please refer to chapter 32 / 32.1 Information regarding Software Versions By purchase of any of products described in this document the customer accepts the document's validity and declares their agreement and understanding of its contents and recommendations. Panasonic reserves the right to make changes as required without notification. Power Electronics R&D Center Wireless Connectivity Panasonic Industrial Devices Europe GmbH APPROVED genehmigt CHECKED gepruft DESIGNED erstellt CLASSIFICATION SUBJECT PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 2 of 53 DATE 11.07.2014 TABLE OF CONTENTS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. Scope of this Document ................................................................................................ 5 History for this Document .............................................................................................. 5 Data Sheet Status ......................................................................................................... 5 Related Documents ....................................................................................................... 5 Key Features ................................................................................................................. 6 Applications for the Module ........................................................................................... 6 Wireless Local Area Network (WLAN) ........................................................................... 7 Bluetooth 4.0 ................................................................................................................. 7 Description for the Module............................................................................................. 8 Difference PAN9055 to PAN9045.................................................................................. 8 Detailed Description ...................................................................................................... 9 11.1. PAN9055 / PAN9045 Terminal Layout ................................................................. 9 11.2. PAN9055 / PAN9045 Common Terminal Pin-Configuration ............................... 10 11.3. PAN9055 / PAN9045 SDIO Specific Terminal Pin-Configuration........................ 11 11.4. PAN9045 RF-Terminal Pin-Configurations ......................................................... 11 General Features ........................................................................................................ 12 HOST Interfaces ......................................................................................................... 12 13.1. USB 2.0 Interface ............................................................................................... 12 13.2. SDIO 3.0 Interface ............................................................................................. 12 13.3. High-speed UART Interface ............................................................................... 12 Peripheral Bus Interface .............................................................................................. 13 Audio Interface Features ............................................................................................. 13 15.1. Audio Codec Interface ........................................................................................ 13 15.2. PCM Interface .................................................................................................... 13 WLAN Features........................................................................................................... 14 16.1. IEEE 802.11 / Standards .................................................................................... 14 16.2. WLAN MAC ........................................................................................................ 14 16.3. WLAN Baseband................................................................................................ 15 16.4. WLAN Radio ...................................................................................................... 15 16.5. WLAN RF Path .................................................................................................. 15 16.6. WLAN Encryption ............................................................................................... 15 Bluetooth Features ...................................................................................................... 16 17.1. General .............................................................................................................. 16 17.2. Bluetooth Classic ............................................................................................... 16 17.3. Bluetooth Low Energy (BLE) .............................................................................. 16 PAN9055 / PAN9045 Block Diagram ........................................................................... 17 18.1. PAN9055 Variant ............................................................................................... 17 18.2. PAN9045 Variant ............................................................................................... 17 Key Parts List .............................................................................................................. 18 Test Conditions ........................................................................................................... 18 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 21. 22. 23. PRODUCT SPECIFICATION PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 3 of 53 DATE 11.07.2014 General Requirements and Operation ......................................................................... 19 21.1. Absolute Maximum Ratings ................................................................................ 19 21.2. Recommended Operating Conditions................................................................. 19 21.3. Digital Pin Characteristics .................................................................................. 20 21.3.1. VIO with VDD 3.3V Operation for GPIO's ............................................... 20 21.3.2. SD_VIO 1.8V Operation for SDIO I/F .................................................... 20 21.3.1. SD_VIO 3.3V Operation for SDIO I/F .................................................... 20 21.4. Electrical characeristics ...................................................................................... 21 21.4.1. Current consumption WLAN and Bluetooth with USB I/F ...................... 21 21.4.2. Current consumption WLAN and Bluetooth with SDIO I/F ..................... 22 21.5. Internal Operating Frequencies .......................................................................... 22 21.6. Coexistence Interface Specification.................................................................... 23 21.6.1. Marvell(R) 3/4-Wire Timing Data .............................................................. 23 21.6.2. WL_ACTIVE 2/3/4-Wire Timing Data .................................................... 24 21.7. Host Interface Specification ................................................................................ 25 21.7.1. USB 2.0 Host Interface ......................................................................... 25 21.7.1.1. Common Electrical Characteristics ................................................... 25 21.7.1.2. High Speed Source Electrical Characteristics ................................... 26 21.7.1.3. Full Speed Source Electrical Characteristics ..................................... 27 21.7.1.4. Device Event Timings ....................................................................... 27 21.7.2. SDIO Host Interface .............................................................................. 29 21.7.2.1. SDIO Timing Data - Default and High Speed Modes (3.3V) ............. 29 21.7.2.2. SDIO Protocol Timing - Default Speed Mode (3.3V) ......................... 29 21.7.2.3. SDIO Protocol Timing - High Speed Mode (3.3V)............................. 29 21.7.2.4. SDIO Timing Data - SDR12, SDR25, SDR50 Modes (1.8V) ............. 30 21.7.2.5. SDIO Protocol Timing - SDR12, SDR25, SDR50 Modes (1.8V) ....... 30 21.7.3. High-Speed UART Interface.................................................................. 30 21.7.3.1. UART Baud Rates Supported ........................................................... 30 21.8. Peripheral Interface Specification ....................................................................... 31 21.8.1. GPIO ..................................................................................................... 31 21.8.1. LED Mode of LED0 and LED1 .............................................................. 31 RF Electrical Characteristics ....................................................................................... 32 22.1. WLAN Radio Specification ................................................................................. 32 22.2. WLAN RF Characteristics .................................................................................. 33 22.2.1. RF Characteristics for IEEE 802.11b ..................................................... 33 22.2.2. RF Characteristics for IEEE 802.11g ..................................................... 34 22.2.3. RF Characteristics for IEEE 802.11n (BW 20 MHz) ............................... 35 22.2.4. RF Characteristics for IEEE 802.11n (BW 40 MHz) ............................... 36 22.3. Bluetooth RF Characteristics .............................................................................. 37 Soldering Temperature-Time Profile (for reflow soldering)........................................... 38 23.1. For lead solder ................................................................................................... 38 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. PRODUCT SPECIFICATION PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 4 of 53 DATE 11.07.2014 23.2. For leadfree solder ............................................................................................. 38 PAN9055 / PAN9045 Module Dimension .................................................................... 39 PAN9055 / PAN9045 FootPrint of the Module ............................................................ 40 Case Marking .............................................................................................................. 41 26.1. Example for Marking .......................................................................................... 41 26.2. Marking Definition .............................................................................................. 41 Mechanical Requirements ........................................................................................... 41 Development of Applications ....................................................................................... 42 Reliability Tests ........................................................................................................... 42 Cautions ...................................................................................................................... 42 30.1. Design Notes ..................................................................................................... 42 30.2. Installation Notes................................................................................................ 43 30.3. Usage Conditions Notes..................................................................................... 43 30.4. Storage Notes .................................................................................................... 43 30.5. Safety Cautions .................................................................................................. 44 30.6. Other cautions .................................................................................................... 44 Packaging ................................................................................................................... 45 31.1. PAN9055 / PAN9045 Tape Dimension ............................................................... 45 31.2. Packing in Tape ................................................................................................. 45 31.3. Component Direction ......................................................................................... 46 31.4. Reel Dimension .................................................................................................. 46 31.5. Label for Package .............................................................................................. 47 31.6. Total Package .................................................................................................... 47 Ordering Information ................................................................................................... 48 32.1. Information regarding Software Versions ........................................................... 48 RoHS Declaration ....................................................................................................... 48 Regulatory Information ................................................................................................ 49 34.1. FCC for US ........................................................................................................ 49 34.1.1. FCC Notice ........................................................................................... 49 34.1.2. Caution ................................................................................................. 49 34.1.3. Labeling Requirements ......................................................................... 49 34.1.4. Antenna Warning .................................................................................. 50 34.1.5. Approved Antenna List .......................................................................... 50 34.1.6. RF Exposure PAN9055 ......................................................................... 50 34.2. Industry Canada Certification ............................................................................. 51 34.2.1. IC Notice ............................................................................................... 51 34.2.2. Labeling Requirements ......................................................................... 51 34.3. European R&TTE Declaration of Conformity ...................................................... 52 General Information..................................................................................................... 53 Life Support Policy ...................................................................................................... 53 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 1. PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 5 of 53 DATE 11.07.2014 SCOPE OF THIS DOCUMENT 2x2 MIMO (R)1 This product specification applies to Panasonic's WLAN IEEE 802.11 b/g/n and Bluetooth 4.0 High (R) Speed / Low Energy - Radio Module with series number PAN9055 / PAN9045 ( 88W8797 from Marvell ). 2. HISTORY FOR THIS DOCUMENT 3. Revision Date Modification / Remarks 0.1 July 2014 1st preliminary version DATA SHEET STATUS This data sheet contains the PRELIMINARY specification. Supplementary data will be published at a later date. Panasonic reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Please consult the most recently issued data sheet before initiating or completing a design. 4. RELATED DOCUMENTS For an update, please search in the suitable homepage. 1 [1] PAN9055 and PAN9045 Design-Guide TBP [2] Semiconductor Datasheet (R) 88W8797 from Marvell [3] Application Note Land Grid Array http://www.pideu.panasonic.de/pdf/184ext.pdf [4] REACH and RoHS Certificate http://www.pideu.panasonic.de/pdf/182ext2.jpg Bluetooth is a registered trademark of the Bluetooth Special Interest Group. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 5. PANASONIC'S CODE ENWF9101x1yF REV. 0.1 PAGE 6 of 53 DATE 11.07.2014 KEY FEATURES 6. No. DS-9055-2400-102 PRODUCT SPECIFICATION Surface Mount Type 26.0 x 13.5 x 2.4 mm Wireless Local Area Network (WLAN) and Bluetooth technology Operating in the 2.4GHz ISM band WLAN 2x2 MIMO operation Supports IEEE 802.11 IEEE 802.11b/g payload data rates IEEE 802.11n high throughput data rates IEEE 802.11i security standards AES-CCMP, WEP, TKIP, AES-CMAC and WAPI IEEE 802.11e Quality of Service (QoS) Supports Bluetooth 4.0 + HS Bluetooth Classic with BT Class 2 or Class 1.5 support Bluetooth High Speed (BT 3.0) Bluetooth Low Energy (BLE) Coexistence with cellular and other 2.4GHz on-chip radios WLAN Tx power up to +18 dBm (IEEE 802.11b CCK) and +14 dBm (IEEE 802.11g ODFM) WLAN High Rx sensitivity -98dBm (IEEE 802.11b DSSS 1Mbps) -76dBm (IEEE 802.11g OFDM 54Mbps) -74dBm (IEEE 802.11n MCS7 HT20 65Mbps) -71dBm (IEEE 802.11n MCS7 HT40 135Mbps) (R) Marvell 88W8797 WLAN / Bluetooth System-on-Chip (SoC) solution inside High performance low power CPU core Four powerful independent DMA channels Power Management Unit with internal Sleep Clock (for Power Save Mode) Internal crystal oscillator (38.4MHz) USB 2.0, SDIO 3.0 and HS-UART interface Integrated shielding to resist EMI Manufactured in conformance with RoHS APPLICATIONS FOR THE MODULE All Embedded Wireless Applications Platform Consumer Electronic Portable Application Health & Fitness Smart Energy PANASONIC INDUSTRIAL DEVICES EUROPE GMBH Game Console, Imaging Home AV Entertainment, TV, Set-top Boxes, Media Servers Handsets, AV Device, Tablet, eBook Home Gateways, Medical devices Thermostat, Control panels www.pideu.panasonic.de CLASSIFICATION SUBJECT WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 7. PRODUCT SPECIFICATION PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 7 of 53 DATE 11.07.2014 WIRELESS LOCAL AREA NETWORK (WLAN) Wireless Local Area Network (WLAN) is indicating a local radio network meant as a part of the standard IEEE 802.11 family. The IEEE 802.11 is an international standard describing the wireless network. The standard defines the lower layers of the OSI model for wireless communication with the Physical Layer (PHY) and the Data Link Layer (DLL) with its two sub-layers Logical Link Control (LLC) and Media Access Control (MAC). It makes it possible to use any protocol over a IEEE 802.11 wireless network as used at an Ethernet network. Basically WLAN networks using two operating modes for connecting station computers (STA) equipped with a wireless network adapter. The first one is the infrastructure mode where the wireless clients are connected via one or more access points (AP) to a wired network. In this case the network is configured with the same Service Set Identifier (SSID) network name in order to communicate. The second one is the Ad-hoc mode where wireless clients are connected without any access point to the internet. WLAN devices typically have a higher transmit power to cover a radio range about 100m. Furthermore WLAN is commonly used to transmit high throughput data using upon other the Orthogonal Frequency Division Multiplexing (OFDM) modulation technique. The Carrier Sense Multiple Access with Collosion Avoidance (CSMA/CA) mechanism enables the parallel access of more than one device to the media of a IEEE 802.11 network. By implementation of security mechanisms like Adavanced Encryption Standard (AES) with Counter Mode CBC-MAC Protocol (CCMP) or Cipher-Based Message Authentication Code (CMAC) and Wired Equivalent Privacy (WEP) with Temporal Key Integrity Protocol (TKIP) the network is supporting the security standard IEEE 802.11i. Video, voice and multimedia applications are supported by the IEEE 802.11e Quality of Service amendment. 8. BLUETOOTH 4.0 Bluetooth Low Energy (BLE) is a part of Bluetooth Version 4.0, which covers both BLE as well as BT Classic 2.1 and 3.0. If both are implemented in one device it is called dual mode. Dual mode chips implement the low energy specification, providing connectivity to battery applications. Dual mode combines low energy with the power of classic Bluetooth and are likely to become a de facto feature in almost all new Bluetooth enabled cellular phones, computers or portable communication nodes. Bluetooth Low Energy (BLE) is not backwards compatible with previous Bluetooth classic standards (2.1+EDR or 3.0). Dual mode Bluetooth 4.0 is backwards compatible but is not practical for low power devices but targeted to gateway products. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 9. PRODUCT SPECIFICATION PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 8 of 53 DATE 11.07.2014 DESCRIPTION FOR THE MODULE The ENWF9101x1yF is a 2.4GHz ISM band wireless radio module for implementing WLAN and Bluetooth functionality into various electronic devices. A block diagram can be found in chapter 17. The ENWF9101x1yF is a cost-effective, low-power operation, system-on-chip (SoC) solution for WLAN and Bluetooth applications. It enables wireless network adapters and cards to be built with low total bill-ofmaterial costs. The ENWF9101x1yF combines an excellent IEEE 802.11 and BT4.0 wireless radio, baseband processor, medium access controller, encryption unit, CPU, boot ROM with patching capability, internal SRAM, in-system programmable flash memory and many other powerful supporting features and peripherals. The low-power operation supporting deep sleep and standby modes by using the on-board power management unit. The ENWF9101x1yF is suitable for wireless network systems based on WLAN IEEE 802.11 b/g/n and Bluetooth BT4.0 (2.4GHz) where small form factor, highly integration, high throughput data rates and low RF expertise are required. Panasonic offers the software package supporting various Fedora Core Kernel versions. It includes the WLAN/BT SoC Firmware binary that powers the WLAN/BT SoC for client (STA), micro access point (uAP), Ad-hoc mode (Wi-Fi direct), Bluetooth Classic, High Speed and Low Energy (BLE) applications. In addition it includes the HOST Driver-Firmware Interface (API) which represents the interface between the host driver and SoC firmware. For WLAN the Driver-Firmware Interface handles all 802.11 MAC management tasks by converting standard 802.3 frames to the SoC firmware to transmit over the wireless link as 802.11 frames and processes the received 802.11 frames and converts them into 802.3 frames before forwarding them to the host driver. The HOST driver is seperated in three modules. The Standard Ethernet driver, the 802.11 Extensions and the Hardware Interface Driver. The 802.11 Extensions module extends the Standard Ethernet driver in order to view and control the state of the WLAN adapter. For Bluetooth the Driver-Firmware Interface handles the BT Baseband, Link Manager Protocol (LMP) and HCI functionality in cooperation with the CPU. The Hardware Interface Driver controls the hardware interface on the HOST side. Furtheron the software (R) package from Marvell consists of various applications, demonstrations and utilities. Refer to [1] PAN9055 and PAN9045 Design-Guide and chapter 32. Ordering Information. Please contact your local sales office for further details on additional options and services: www.panasonic.com/rfmodules for the US, http://industrial.panasonic.com/eu/i/29606/wireless_modules/wireless_modules.html for EU or write an e-mail to wireless@eu.panasonic.com. 10. DIFFERENCE PAN9055 TO PAN9045 The PAN9045 is the non antenna version with two bottom pads where the PAN9055 is the version with two antennas. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 11. PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 9 of 53 DATE 11.07.2014 DETAILED DESCRIPTION 11.1. PAN9055 / PAN9045 TERMINAL LAYOUT The USB pins are marked with a blue rectangular box. The SDIO pins are marked with a blue dashed rectangular box. The two PAN9045 antenna pins are marked with blue circles. Top View, Application PCB PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT No. DS-9055-2400-102 PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 PANASONIC'S CODE ENWF9101x1yF REV. 0.1 PAGE 10 of 53 DATE 11.07.2014 11.2. PAN9055 / PAN9045 COMMON TERMINAL PIN-CONFIGURATION No Pin Name Pin Type 1 2..7 8 9 GND ... RESETn PDn Ground Pin ... Input Signal Input Signal 10 S_CSN / CON2 Output / Input 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 GND NC GND GND GND GND NC GND 3.3V RF 3.3V RF CON0 CON1 UART_SOUT UART_SIN UART_RTS UART_CTS GPIO4 GND 3.3V 3.3V 3.3V USB USB_DMNS USB_DPLS SD_VIO Ground Pin NC Ground Pin Ground Pin Ground Pin Ground Pin NC Ground Pin Power Power Digital I/O Digital I/O Output Signal Input Signal Output Signal Input Signal Digital I/O Ground Pin Power Power Power DD+ Power A1 TMS / BT_FREQ Input Signal A2 A3 A4 A5 TDO / BT_REQ S_WB S_CLK S_DAT Output / Input Input Signal Output Signal Output Signal B1 TCK / BT_GRANTn Input / Output B2 TDI / BT_STATE Input Signal B3 B4 B5 C1 C2 C3 C4 C5 D1 D2 D3 D4 D5 E1 E2 E3 E4 E5 F1 F2 F3 F4 F5 GND GND GND CHIP_WAKEUP I2S2_LRCLK GND GND GND I2S2_DOUT I2S2_DIN PCM_SYNC GND GND I2S2_BCLK LED1 PCM_CLK GND PCM_DOUT HOST_WAKEUP LED0 PCM_DIN PCM_MCLK GND Ground Pin Ground Pin Ground Pin Digital I/O Output / Input Ground Pin Ground Pin Ground Pin Output Signal Input Signal Input / Output Ground Pin Ground Pin Input / Output Digital Output Input / Output Ground Pin Output Signal Digital I/O Digital Output Input Signal Output Signal Ground Pin Description Connect to Ground ... for SDIO specific terminals see chapter 11.3 Reset, active-low Power down, active-low S_CSN: Chip Select for external SPI EEPROM, chip select from the SoC CON2: Firmware Boot option Connect to Ground ... for PAN9045 see chapter 11.4 Connect to Ground Connect to Ground Connect to Ground Connect to Ground ... for PAN9045 see chapter 11.4 Connect to Ground 3.0V - 3.6V power supply connection 3.0V - 3.6V power supply connection CON0: Firmware Boot option see chapter CON1: Firmware Boot option see chapter Serial data output to modem, data set, or peripheral device Serial data input from modem, data set, or peripheral device Request-to-Send output to modem, data set, or peripheral device (active low) Clear-to-Send input from modem, data set, or peripheral device (active low) Port 4 - GPIO[4] Connect to Ground 3.0V - 3.6V power supply connection 3.0V - 3.6V power supply connection 3.0V - 3.6V power supply connection USB Bus Data Minus USB Bus Data Plus 1.8V or 3.3V Digital I/O SDIO Power Supply TMS: JTAG controller select BT_FREQ: Information BT using channel which overlaps WLAN channel or not TDO: JTAG test data output / BT_REQ: BT device request access to medium Serial Read/Write Control Signal input, SPI EEPROM serial data to the SoC Serial Clock Signal output, SPI EEPROM serial clock from the SoC Serial Data output, SPI EEPROM serial data from the SoC TCK: JTAG test clock BT_GRANTn: Indicate permission to transmit, low BT can transmit TDI: JTAG test data input BT_STATE: Information BT_REQ priority (1- or 2-bit) and direction BT RX/TX Connect to Ground Connect to Ground Connect to Ground Port 18 - optional GPIO[18] or Host-to-Chip wake-up I2S Audio Left/Right Clock, Master mode as output, Slave mode as input Connect to Ground Connect to Ground Connect to Ground I2S Audio output data (for playback) I2S Audio input data (for recording) PCM Sync Pulse Signal, output if PCM Master, input if PCM Slave Connect to Ground Connect to Ground I2S Audio Bit Clock, Master mode as output, Slave mode as input Port 17 - LED output with typ. 10mA drive capability PCM Clock Signal, output if PCM Master, input if PCM Slave Connect to Ground PCM Data Output Signal Port 16 - optional GPIO[16] or Chip-to-Host wake-up Port 1 - LED output with typ. 10mA drive capability PCM Data Input Signal PCM Clock Signal, optional clock used for some codec derived from PCM_CLK Connect to Ground PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT No. DS-9055-2400-102 PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 PANASONIC'S CODE ENWF9101x1yF REV. 0.1 PAGE 11 of 53 DATE 11.07.2014 11.3. PAN9055 / PAN9045 SDIO SPECIFIC TERMINAL PIN-CONFIGURATION No 2 3 4 5 6 7 Pin Name SD_CMD SD_DAT[0] SD_DAT[1] SD_DAT[2] SD_DAT[3] SD_CLK Pin Type Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O 4-bit mode Description 1-bit mode Command Line Data Line bit [0] Data Line Data Line bit [1] Interrupt Data Line bit [2] or ... Read Wait (optional) Data Line bit [3] Not used Clock Clock SPI mode Data Input Data Output Interrupt Reserved Chip Select, active low Clock 11.4. PAN9045 RF-TERMINAL PIN-CONFIGURATIONS No 12 17 Pin Name RF_B RF_A Pin Type RF Port B RF Port A Description 50 bottom pad 50 bottom pad PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 12. PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 12 of 53 DATE 11.07.2014 GENERAL FEATURES 13. PRODUCT SPECIFICATION Embedded WLAN / BT SoC with following features: Integrated CPU with maximum clock speed of 256 MHz Single-chip integration of IEEE 802.11 2x2 MIMO and BT4.0 wireless radio, baseband, MAC, CPU, memory and HOST interface SRAM for Tx frame queues and Rx data buffer Boot ROM and ROM patching capability Independent Four-Channel Direct Memory Access (DMA) Low power operation supporting deep sleep and stand-by modes Optional power management with internal sleep clock crystal unit for near zero deep sleep HOST INTERFACES 13.1. USB 2.0 INTERFACE Compliant with the Universal Serial Bus Specification, Revision 2.0 Allows HOST controller using USB cable bus and USB 2.0 device interface High/full speed operation with (480/12 Mbps) Suspend / host resume / device resume (remote wake-up) Supports Link Power Management (LPM), corresponding host resume or device resume (remote wakeup) to exit from L1 sleep state USB 2.0 device interface with integrated level shifter for 3.3V signal level 13.2. SDIO 3.0 INTERFACE Supports SDIO 3.0 Standard SDIO device interface that conforms to the industry standard SDIO Full-Speed card specification Supports SPI, 1-bit SDIO and 4-bit SDIO transfer modes at the full clock range of 0 to 100MHz Special interrupt register for information exchange Allows card to interrupt host SoC acts as a device on a SDIO bus 13.3. HIGH-SPEED UART INTERFACE Supports high-speed Universal Asynchronous Receiver / Transmitter (UART) interface Compliant with the industry standard 16550 specification High-speed baud rates are supported to provide the physical transport between the device and the host for exchanging Bluetooth data FIFO mode permanently selected for transmit and receive operations Two pins for transmit, receive and two for flow control Interrupt triggers for low-power, high throughput operation PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 14. ENWF9101x1yF REV. 0.1 PAGE 13 of 53 DATE 11.07.2014 PERIPHERAL BUS INTERFACE 15. PANASONIC'S CODE No. DS-9055-2400-102 Embedded SoC with following features: Clocked Serial Unit (CSU) 2-Wire Serial Interface (TWSI) 1-Wire Serial Interface SPI Serial (EEPROM) Interface General-Purpose I/O (GPIO) Interface User-defined GPIOs, I/O configured to either input or output GPIOs independently controlled Two GPIOs with LED output functionality LED Pulse Stretching to observe short duration of status events Two software controlled blink rates to indicate events One-Time Programmable Memory (OTP) Storing calibration data and hardware information of the device Programmed during production process of device Device performs calibration when it is powered up AUDIO INTERFACE FEATURES 15.1. AUDIO CODEC INTERFACE Class D Audio Amplifier 2 I S (Inter-IC Sound) interface for audio data connection to ADC and DAC 2 Master and slave mode for I S, MSB and LSB audio interfaces 2 Tri-state I S interface capability 15.2. PCM INTERFACE Master or slave mode PCM bit width size of 8 bits or 16 bits Up to 4 slots with configurable bit width and start positions Short frame and long frame synchronization Tri-state PCM interface capability PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 16. PRODUCT SPECIFICATION PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 14 of 53 DATE 11.07.2014 WLAN FEATURES 16.1. IEEE 802.11 / STANDARDS 802.11 data rates 1 and 2 Mbps (DSSS) 802.11b data rates 5.5 and 11 Mbps (CCK) 802.11g data rates 6, 9, 12, 18, 24, 36, 48 and 54 Mbps (OFDM) 802.11b/g performance enhancements 802.11n compliant with maximum data rates up to 145 Mbps (20 MHz channel) and 300 Mbps (40 MHz channel) 802.11d international roaming 802.11i enhanced security (WEP, WPA, WPA2) 802.11k radio resource measurement 802.11n block acknowledgement extensions 802.11r fast hand-off for AP roaming 802.11w protected management frames Fully supports clients (stations) implementing IEEE Power Save mode Wi-Fi Direct connectivity 16.2. WLAN MAC Ad-Hoc and Infrastructure Modes RTS/CTS for operation und DCF Hardware filtering of 32 multicast addresses and duplicate frame detection for up to 32 unicast addresses WLAN SoC with Tx and Rx FIFO for maximum throughput Open System and Shared Key Authentication services A-MPDU Rx (de-aggregation) and Tx (aggregation) 20/40 MHz channel coexistence Reduced Inter-Frame Spacing (RIFS) receive Management Information Base (MIB) counter Radio resource measurement counters Quality of service queues Block acknowledgement with 802.11n extensions Beamforming Supports beamforming to 802.11n MIMO and SISO devices 802.11n explicit beamformer, supports NDP and Stagger sounding 802.11n explicit beamformee, supports immediate feedback generation using un-compress and compress steering matrix or delayed feedback of all feedback types TIM frame transition Multiple-BSSID and Multiple-Station operation Transmit rate adaptation Transmit power control Long and short preamble generation on a frame-by-frame basis for 802.11b frames (R) Marvell Mobile Hotspot technology (MMH) PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 15 of 53 DATE 11.07.2014 16.3. WLAN BASEBAND 802.11n 2x2 MIMO (WLAN SoC with MIMO RF radio) Backward compatibility with legacy 802.11b/g technology WLAN / Bluetooth LNA sharing PHY data rates up to 300 Mbps (802.11n - MCS15) 20 MHz bandwidth/channel, 40 MHz bandwidth/channel, upper/lower 20 MHz packets in 40 MHz channel and 20 MHz duplicate legacy packets in 40 MHz channel mode operation Modulation and Coding Scheme MCS 0 ~ 15 and MCS 32 (duplicate 6 Mbps) Radio resource measurement Optional 802.11n MIMO features: 20/40 MHz coexistence 1 spatial stream Space-Time-Block-Coding (STBC) reception and transmission Short Guard Interval RIFS on receive path Implicit beamforming Explicit beamformer and beamformee support Greenfield Tx/Rx Power save features 16.4. WLAN RADIO 20 and 40 MHz channel bandwidth Shared WLAN / Bluetooth receive input scheme for 2.4 GHz band Embedded WLAN SoC with following features: Direct conversion radio (no SAW filter) Closed/Open loop power control (0.5 dB step increments) Optimized Tx gain distribution for linearity and noise performance Fine channel step with AFC (adaptive frequency control) 16.5. WLAN RF PATH Shared WLAN / Bluetooth receive input scheme for 2.4 GHz band Two RF pathes with following features: Two separate Front-End-Modules (FEM) for each RF path st 1 FEM with integrated 2.4GHz Tx/Rx switch, Power Amplifier (PA) and Low Noise Amplifier (LNA) path nd 2 FEM with integrated 2.4GHz Tx/Rx/BT switch, Power Amplifier (PA), Low Noise Amplifier (LNA) and RF Bypass path Gain selectable LNAs with optimized noise figure and power consumption Power Amplifiers with power control 16.6. WLAN ENCRYPTION Embedded WLAN SoC with following features: WEP 64-bit and 128-bit encryption with hardware TKIP processing (WPA) AES-CCMP hardware implementation as part of 802.11i security standard (WPA2) Enhanced AES engine performance AES-Chipher-Based Message Authentication Code (CMAC) as part of the 802.11w security standard WLAN Authentication and Privacy Infrastructure (WAPI) PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 17. PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 16 of 53 DATE 11.07.2014 BLUETOOTH FEATURES 17.1. GENERAL Supports Bluetooth 4.0 + High Speed Shared Tx/Rx path for Bluetooth 2 Digital Audio Interface including PCM interface for voice applications and I S for digital stereo applications BDR/EDR, BLE and WLAN coexistence WLAN/Bluetooth Coexistence (BCA) protocol support 17.2. BLUETOOTH CLASSIC Bluetooth Classic with BT Class 2 or Class 1.5 support Bluetooth High Speed (BT 3.0) Baseband and radio Basic Data Rate (BDR) and Enhanced Data Rate (EDR) packet types with 1Mbps (GFSK), 2Mbps (/4-DQPSK) and 3Mbps (8DPSK) Fully functional Bluetooth baseband with Adaptive Frequency Hopping (AFH), forward error correction, header error control, access code correlation, CRC, encryption bit stream generation and whitening Adaptive Frequency Hopping (AFH) including Packet Loss Rate (PLR) and RSSI Interlaced scan for faster connection setup Simultaneous active ACL connection support Automatic ACL packet type selection Full master and slave piconet support Scatternet support Standard UART and SDIO HCI transport layer SCO/eSCO links with hardware accelerated audio signal processing and hardware supported PPEC algorithm for speech quality improvement All standard SCO/eSCO voice coding All standard pairing, authentication, link key and encryption operations Standard Bluetooth power saving mechanism (i.e. hold, sniff modes and snif f-sub rating) Enhanced low power scan mode Enhanced Power Control (EPC) Channel Quality Driven (CQD) data rate SBC off load for A2DP streaming Wideband Speech (WBS) support (1 WBS link) 17.3. BLUETOOTH LOW ENERGY (BLE) Advertiser, Scanner, Initiator, Master and Slave roles support (connects up to 16 links) Shared RF with BDR/EDR Encryption AES support Hardware support for intelligent Adaptive Frequency Hopping (AFH) PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 18. PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 17 of 53 DATE 11.07.2014 PAN9055 / PAN9045 BLOCK DIAGRAM 18.1. PAN9055 VARIANT 18.2. PAN9045 VARIANT PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 19. 20. PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 18 of 53 DATE 11.07.2014 KEY PARTS LIST Part Name Material P.W.Board Glass cloth epoxide resin with gold plating Casing Material: C7521 or ZSNC S1S8 8/8, thickness 0.30mm IC part name 88W8797 (Marvell , www.marvell.com) (R) TEST CONDITIONS Measurements shall be made under operating free-air temperature range unless otherwise specified. Temperature Humidity Supply Voltage 25 10C 40 to 85%RH 3.3V PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 21. PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 19 of 53 DATE 11.07.2014 GENERAL REQUIREMENTS AND OPERATION All specifications are over temperature and process, unless indicated otherwise. 21.1. ABSOLUTE MAXIMUM RATINGS The maximum ratings may not be exceeded under any circumstances, not even momentarily and individually, as permanent damage to the module will result. Symbol Parameter Condition TSTOR Storage temperature VESD ESD robustness Min. Typ. -40 All pads, according to human-body model, JEDEC STD 22, method A114 According to charged-device model, JEDEC STD 22, method C101 Max. Units +125 C 1000 V 500 V +20 dBm PRF RF input level VDDMAX Maximum voltage Maximum power supply voltage from any pin with respect to VSS (GND) -0.3 3.9 V VIO Voltage on any digital pin GPIOs, PDn, RESETn, Coex I/F -0.3 VDDMAX V VUSBMAX USB Maximum voltage Maximum power supply voltage from any pin with respect to VSS (GND) -0.3 3.9 V -0.3 3.9 V -0.3 2.1 V 3V3 SDIO Maximum voltage VIO_SDMAX 1V8 SDIO Maximum voltage Maximum power supply voltage from any pin with respect to VSS (GND) 21.2. RECOMMENDED OPERATING CONDITIONS The maximum ratings may not be exceeded under any circumstances, not even momentarily and individually, as permanent damage to the module will result. Symbol Parameter TA Ambient operating temperature range Condition Commercial Grade (refer to chapter 32.) Extended Grade 2 VDD 3V3 Supply voltage VUSB 3V3 USB Supply voltage 2 3V3 SDIO Supply voltage 2 VIO_SD 1V8 SDIO Supply voltage 2 2 Min. (refer to chapter 32.) Voltage on pins 19 / 20 (3.3V RF), 29 / 30 (3.3V) I/O supply voltage VIO internally connected to VDD Voltage on pin 31 (3.3V USB) Supply voltage VUSB connected to 3.3V USB Voltage on pin 34 (SD_VIO) Supply voltage VIO_SD connected to SD_VIO Voltage on pin 34 (SD_VIO) Supply voltage VIO_SD connected to SD_VIO Typ. Max. Units 0 +70 C -30 +85 C 3.0 3.3 3.6 V 3.0 3.3 3.6 V 3.0 3.3 3.6 V 1.6 1.8 2.0 V The supply current must be limited to max. 1A PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 20 of 53 DATE 11.07.2014 21.3. DIGITAL PIN CHARACTERISTICS 21.3.1. VIO with VDD 3.3V Operation for GPIO's Symbol Parameter Condition VIH High level input voltage 3 3 VIL Low level input voltage VHYS Input hysteresis voltage 3 3 VOH High level output voltage VOL Low level output voltage 3 Min. Typ. Max. Units 3.3V Operation (VIO = VDD) 0.7VDD VDD+0.3 V 3.3V Operation (VIO = VDD) -0.3 0.3VDD V 3.3V Operation (VIO = VDD) 200 3.3V Operation (VIO = VDD) VDD - 0.4 mV V 3.3V Operation (VIO = VDD) 0.4 V 21.3.2. SD_VIO 1.8V Operation for SDIO I/F Symbol Parameter Condition Min. VIH High level input voltage 3 1.8V Operation (VIO_SD = 1.8V) VIL Low level input voltage 3 1.8V Operation (VIO_SD = 1.8V) VHYS Input hysteresis voltage 3 3 VOH High level output voltage VOL Low level output voltage 3 Max. Units 0.7VIO_SD VIO_SD+0.3 V -0.3 0.3VIO_SD V 1.8V Operation (VIO_SD = 1.8V) 150 1.8V Operation (VIO_SD = 1.8V) VIO_SD - 0.4 Typ. mV V 1.8V Operation (VIO_SD = 1.8V) 0.4 V 21.3.1. SD_VIO 3.3V Operation for SDIO I/F 3 Symbol Parameter Condition Min. VIH High level input voltage 3 3.3V Operation (VIO_SD = 3.3V) VIL Low level input voltage 3 3.3V Operation (VIO_SD = 3.3V) VHYS Input hysteresis voltage 3 3 VOH High level output voltage VOL Low level output voltage 3 Max. Units 0.7VIO_SD VIO_SD+0.3 V -0.3 0.3VIO_SD V 3.3V Operation (VIO_SD = 3.3V) 200 3.3V Operation (VIO_SD = 3.3V) VIO_SD - 0.4 3.3V Operation (VIO_SD = 3.3V) Typ. mV V 0.4 V The capacitive load should not be larger than 50 pF for all I/O's when using the default driver strength settings. Generally, large capacitance loads increase the overall current consumption. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT No. DS-9055-2400-102 PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 PANASONIC'S CODE ENWF9101x1yF REV. 0.1 PAGE 21 of 53 DATE 11.07.2014 21.4. ELECTRICAL CHARACERISTICS The current consumption depends on the user scenario and the setup and timing in the power modes. Assume VDD = 3.3V, Tamb = 25C if nothing else stated 21.4.1. Current consumption WLAN and Bluetooth with USB I/F Symbol Parameter Current Consumption Mode Condition Min. Typ. PTX = +18 dBm for 802.11b @ 11 Mbps TBD PTX = +14 dBm for 802.11g @ 54 Mbps ITX WLAN WLAN IRX WLAN IIEEE-PS 5 Units mA mA PTX = +13 dBm 802.11n @ MCS7 / 72Mbps / HT20 / 1x1 MIMO PTX = +13 dBm 802.11n @ MCS15 / 150Mbps / HT40 / 1x1 MIMO PTX = +13 dBm 802.11n @ MCS7 / 144.5Mbps / HT20 / 2x2 MIMO PTX = +13 dBm 802.11n @ MCS15 / 300Mbps / HT40 / 2x2 MIMO Active Transmit 4 Max. mA mA mA mA 802.11b @ 11 Mbps mA 802.11g @ 54 Mbps mA 802.11n @ MCS7 / 72Mbps / HT20 / 1x1 MIMO mA 802.11n @ MCS15 / 150Mbps / HT40 / 1x1 MIMO mA 802.11n @ MCS7 / 144.5Mbps / HT20 / 2x2 MIMO mA 802.11n @ MCS15 / 300Mbps / HT40 / 2x2 MIMO mA DTIM = 1 with beacon interval 100ms A PTX BT = +4 dBm / USB Active mA Active Receive 6 IEEE Power Save 7 ITX BT PTX BT = +4 dBm / USB Suspend 8 mA Peak BT BT (BDR) (EDR) IRX BT USB Active mA USB Suspend mA ISCAN BT Page / Inquiry Scan 1.28s @ normal mode mA ISNIFF BT ACL Sniff 1.28s mA IA2DP BT A2DP BDR / EDR @ 330 Kbps (3M baud rate) mA PTX BLE = +4 dBm mA ITX BLE Peak BLE BLE IRX BLE 4 mA 9 IPDn Power Down IDeepSleep Deep Sleep 10 WLAN and BT Grounding of PDn pin A Low-power state used in sleep state A Peak values for specified output power level and data rate with UDP traffic between the AP and Device (STA). 5 Using WLAN Client mode. Bluetooth is in Deep Sleep during this mode. 6 Peak values for specified data rate with UDP traffic between the AP and DUT. 7 In IEEE Power Save the device automatically wakes up on beacons. This is dependent on the DTIM value of the AP it is connected to. If it is a DTIM value of 1 along with a beacon interval of 100ms, the device wakes up every 100ms. 8 USB Suspend Mode is valid only for the USB Host interface. The low-power device automatically enters a suspend state after 3ms of no bus activity. 9 Power Down state can be achieved by grounding the PDn pin. All internal clocks are shut down, the registers and memory are not maintained. Upon exiting power down mode, a rest is automatically performed and a firmware re-download is required. 10 It is a low-power mode used in the deep sleep state of power save mode. In this case the external reference clock and many WLAN SoC specific blocks are switched-off. Only an internal slow sleep clock is used to maintain register and memory states. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 22 of 53 DATE 11.07.2014 21.4.2. Current consumption WLAN and Bluetooth with SDIO I/F Symbol Parameter Current Consumption Mode Condition Min. Typ. PTX = +18 dBm for 802.11b @ 11 Mbps Max. TBD mA PTX = +14 dBm for 802.11g @ 54 Mbps ITX WLAN WLAN IRX WLAN IIEEE-PS mA PTX = +13 dBm 802.11n @ MCS7 / 72Mbps / HT20 / 1x1 MIMO PTX = +13 dBm 802.11n @ MCS15 / 150Mbps / HT40 / 1x1 MIMO PTX = +13 dBm 802.11n @ MCS7 / 144.5Mbps / HT20 / 2x2 MIMO PTX = +13 dBm 802.11n @ MCS15 / 300Mbps / HT40 / 2x2 MIMO Active Transmit Units mA mA mA mA 802.11b @ 11 Mbps mA 802.11g @ 54 Mbps mA 802.11n @ MCS7 / 72Mbps / HT20 / 1x1 MIMO mA 802.11n @ MCS15 / 150Mbps / HT40 / 1x1 MIMO mA 802.11n @ MCS7 / 144.5Mbps / HT20 / 2x2 MIMO mA 802.11n @ MCS15 / 300Mbps / HT40 / 2x2 MIMO mA DTIM = 1 with beacon interval 100ms A PTX BT = +4 dBm / USB Active mA PTX BT = +4 dBm / USB Suspend mA USB Active mA USB Suspend mA Active Receive IEEE Power Save ITX BT Peak BT BT (BDR) (EDR) IRX BT ISCAN BT Page / Inquiry Scan 1.28s @ normal mode mA ISNIFF BT ACL Sniff 1.28s mA IA2DP BT A2DP BDR / EDR @ 330 Kbps (3M baud rate) mA PTX BLE = +4 dBm mA ITX BLE Peak BLE BLE IRX BLE mA IPDn Power Down IDeepSleep Deep Sleep WLAN and BT Grounding of PDn pin A Low-power state used in sleep state A 21.5. INTERNAL OPERATING FREQUENCIES Symbol fSYSCLK fREFCLK fSLEEPCLK 11 Parameter Condition CPU clock speed Refers to clock speed of WLAN SoC's CPU System / Encryption clock speed Crystal fundamental frequency Refers to clock speed of WLAN SoC's System and Encryption Unit Frequency tolerance < 10 ppm over operating temperature and process CMOS input clock signal type, 250 ppm over temperature, aging and process Sleep Clock frequency 11 Min. Typ. Max. Units 256 MHz 171 MHz 38.4 MHz 32.768 kHz Need to use module internal sleep clock crystal unit (optional) when low power operation mode near zero deep sleep is necessary. The internal sleep clock is not necessary for normal power modes. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 23 of 53 DATE 11.07.2014 21.6. COEXISTENCE INTERFACE SPECIFICATION The Coexistence Interface pins are powered from the VIO voltage supply internally connected to VDD = 3.3V. See Chapter 21.3 Digital Pin Characteristics for DC specification. 21.6.1. Marvell(R) 3/4-Wire Timing Data Symbol Parameter T1 Priority[0] info is valid in BT_STATE on and after T1 from BT_REQ rise. 0 1 100 s T2 TxRx Info is valid in BT_STATE on and after T2. The BT_STATE must hold until there is any change of direction in the next slots. 2 19 100 s T3 Time from TxRx Info valid to BCA grant decision (T3 = T7 - T4 - T2 - T8 - T1). 2 40 594 s 2 80 594 s 5 40 600 s 0 15 25 s 8 150 600 s 2 10 100 s T4 T5 T6 T7 T8 BT_GRANTn needs to be valid T4 time before the upcoming slot. BT_GRANTn indicates Tx grant, and may also indicate Rx grant. Once a slot is granted, the subsequent slots are also granted unless there is a change in direction from Rx to Tx. Rx to Tx change always re-arbitrates. TxRx Info for the next slot is valid on and after T5 to the start of the next slot. If direction remains the same for the next slot, then BT_STATE must not change during the current slot. If the direction changes for the next slot, the BT_STATE must change only after the last bit of Bluetooth data is transferred; otherwise the transfer may be disrupted. The BT_REQ signal de-asserts T6 time after last bit of Bluetooth data is transferred. Time from BT_REQ rise to first Bluetooth slot boundary. Bluetooth slot boundary is marked by first bit of Bluetooth data. Optional Priority[1] information is valid in BT_STAT on and after T8. This time parameter only exists if BCA is configured for 2-bit priority on same BT_STATE pin. Otherwise, the start of T2 would come after T1. Min. Typ. Max. Units Ttx Slot time (fixed fpr Bluetooth) 625 s Trx Slot time (fixed fpr Bluetooth) 625 s PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 24 of 53 DATE 11.07.2014 21.6.2. WL_ACTIVE 2/3/4-Wire Timing Data Symbol Parameter If WLAN can be stopped, WL_ACTIVE will de-asser prior to Bluetooth slot start (T1 < T2) If the Bluetooth device samples WL_ACTIVE before starting priority transfer, WL_ACTIVE needs to de-assert earlier than the sampling time. Min. T1 T2 Time from BT_PRIORITY rise to start of Bluetooth activity. 20 T3 Time from end of Bluetooth activity to BT_PRIORITY fall. 0 T4 Slot time (fixed fpr Bluetooth) PANASONIC INDUSTRIAL DEVICES EUROPE GMBH Typ. 0 Max. Units 499 s 50 499 s 0 499 s 625 s www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 25 of 53 DATE 11.07.2014 21.7. HOST INTERFACE SPECIFICATION 21.7.1. USB 2.0 Host Interface The USB 2.0 Host Interface pins are powered from the 3.3V_USB voltage supply with 3.3V. It supports the high / full speed operation (480 / 12 Mbps) depending on the USB bus termination. The default mode is high speed operation. 21.7.1.1. Common Electrical Characteristics Symbol Parameter Condition Min. Typ. Max. Units Input Levels for Low / Full Speed VIH Input high voltage (driven) 2.0 V VIHZ Input high voltage (floating) 2.7 VIL Input low voltage VDI Differential input sensitivity 0.2 VCM Differential common mode range 0.8 2.5 V 100 150 mV 525 625 mV 3.6 V 0.8 V V Input Levels for High Speed VHSSQ VHSDSC --VHSCM High-speed squelch detection threshold (differential signal amplitude) High-speed disconnect detection threshold (differential signal amplitude) High-speed differential input signaling levels High-speed data signaling common mode voltage range Specified by eye pattern templates; see Section 7.1.7.2 in the USB 2.0 specification -50 500 mV Output Levels for Low / Full Speed VOL Output low voltage 0.0 0.3 V VOH Output high voltage (driven) 2.8 3.6 V VOSE1 Output SE1 voltage 0.8 VCRS Output signal crossover voltage 1.3 2.0 V V Output Levels for High Speed VHSOI High-speed idle level -10 10 mV VHSOH High-speed data signaling high 360 440 mV VHSOL High-speed data signaling low -10 10 mV VCHIRPJ Chirp J level (differential voltage) 700 1100 mV VCHIRPK Chirp K level (differential voltage) -900 -500 mV PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 26 of 53 DATE 11.07.2014 17.8.1.1 Common Electrical Characteristics (continued) Symbol Parameter Condition Min. Typ. Max. Units Decoupling Capacitance CRPB Upstream facing port bypass capacitance 1 10 F 100 pF 75 pF 80 100 0.900 1.575 k 1.425 3.090 k Input Capacitance for Low / Full Speed CINUB CEDGE Upstream facing port capacitance (without cable) Transceiver edge rate control capacitance Input Impedance for High Speed --- TDR specification for high-speed termination Differential impedance Terminations RPUI RPUA ZINP VTERM Bus pull-up resistor on upstream port (idles bus) Bus pull-up resistor on upstream port (receiving) Input impedance exclusive of pull-up / pull-down (for low / full speed) Termination voltage for upstream facing port pull-up resistor (RPU) k 300 3.0 3.6 V -10 10 mV Terminations in High Speed VHSTERM Termination voltage in high speed 21.7.1.2. High Speed Source Electrical Characteristics Symbol Parameter Condition Min. Typ. Max. Units Driver Characteristics THSR Rise Time (10% - 90%) 500 ps THSF Fall Time (10% - 90%) 500 ps --- Driver waveform requirements ZHSDRV Driver output resistance (which also serves as high speed termination) Specified by eye pattern templates; see Section 7.1.2 in the USB 2.0 specification 40.5 49.5 479.76 480.24 124.9375 125.0625 Clock Timings THSDRAT High speed data rate THSFRAM Microframe interval THSRFI Mbps s 4 highspeed bit times Consecutive microframe interval difference High Speed Data Timings --- Data source jitter Specified by eye pattern templates; see Section 7.1.2.2 in the USB 2.0 specification --- Receiver jitter tolerance Specified by eye pattern templates; see Section 7.1.2.2 in the USB 2.0 specification PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 27 of 53 DATE 11.07.2014 21.7.1.3. Full Speed Source Electrical Characteristics Symbol Parameter Condition Min. Typ. Max. Units Driver Characteristics TFR Rise Time 4 20 ns TFF Fall Time 4 20 ns TFRFM Differential rise and fall time matching 90 111.11 % 11.994 12.006 Mbps 0.9995 1.0005 s 42 ms -3.5 3.5 ns -4 4 ns -2 5 ns -18.5 18.5 ns -9 9 ns 175 ns TFR / TFF Clock Timings TFDRATHS Full speed data rate TFDRATE Frame interval THSRFI Consecutive frame interval difference Average bit rate No clock adjustment Full Speed Data Timings TDJ1 TDJ2 TFDEOP Source Jitter total to next transition (including frequency tolerance) Source Jitter total to paired transitions (including frequency tolerance) Source Jitter for differential transition to SE0 transition TJR1 Receiver Jitter to next transition TJR2 Receiver Jitter to paired transition TFEOPT Source SE0 interval of EOP 160 TFEOPR Receiver SE0 interval of EOP 82 TFST Width of SE0 interval during differential transition ns 14 ns 21.7.1.4. Device Event Timings Symbol TSIGATT TATTDB T2SUSP TSUSAVGI TWTRSM Parameter Time from internal power good device pulling D+/D- beyond VIHZ (min) (signaling attach) Debounce interval provided by USB system software after attach Maximum time a device can draw power > suspend power when bus is continuously in idle state Maximum duration of suspend averaging interval Period of idle bus before device can initiate resum TDRSMUP Duration of driving resume upstream TRSMCY Resume recovery time TRSTRCYI Reset recovery time TIPD Inter-packet delay (for low/full speed) TRSPIPD1 TRSPIPD2 TDSETADDR Condition Device must be remote-wake-up enabled Min. Inter-packet delay for device response with detachable cable for low/full speed Inter-packet delay for device response with captive cable for low/full speed SetAddress() completion time PANASONIC INDUSTRIAL DEVICES EUROPE GMBH Max. Units 100 ms 100 ms 10 ms 1 s 5 1 Provided by USB system software Typ. ms 15 10 ms ms 10 2 ms bit times 6.5 bit times 7.5 bit times 50 ms www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 28 of 53 DATE 11.07.2014 17.8.1.4 Device Event Timings (continued) Symbol TDRQCMPLTND TDRETDATA1 TDRETDATAN THSRSPIPD2 Parameter Condition Min. Time to complete standard request with no data Time to deliver first and subsequent (except last) data for standard request Time to deliver last data for standard request Inter-packet delay for device response with captive cable (high speed) Typ. Max. Units 50 ms 500 ms 50 ms 192 bit times + 52ns ms Reset Handshake Protocol FFILTSE0 TWTRSTFS TWTREV TWTRSTHS TUCH TUCHEND TWTHS TWTFS Time for which a suspended high speed capable device must see a continuous SE0 before beginning the high speed detection handshake Time for which high speed capable device operating in non-suspended full speed must wait after start of SE0 before beginning the high speed detection handshake Time for which high speed capable device operating in high speed must wait after start of SE0 before reverting to full speed Time for which a device must wait after reverting to full speed before sampling the bus state for SE0 and beginning the high speed detection handshake Minimum duration of a Chirp K from a high speed capable device within the reset protocol Time after start of SE0 by which a high speed capable device is required to have completed its Chirp K within the reset protocol Time after end of upstream chirp at which device enters the high speed default state if downstream chirp is detected Time after end of upstream chirp at which device reverts to full speed default state if no downstream chirp is detected PANASONIC INDUSTRIAL DEVICES EUROPE GMBH 2.5 s 2.5 3000 s 3.0 3.125 ms 100 875 s 1.0 1.0 ms 7.01 ms 500 s 2.5 ms www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 29 of 53 DATE 11.07.2014 21.7.2. SDIO Host Interface The SDIO Host Interface pins are powered from the SD_VIO voltage supply with either 3.3V or 1.8V. See Chapter 21.3 Digital Pin Characteristics for DC specification. The SDIO electrical specifications are identical for the 1-bit SDIO and 4-bit SDIO modes. 21.7.2.1. SDIO Timing Data - Default and High Speed Modes (3.3V) Symbol Parameter fPP Clock frequency TWL TWH TISU Clock low time Clock high time Input setup time TIH Input hold time TODLY Output delay time, CL 40 pF (1 card) TOH Output hold time Condition Min. Typ. Max. Units Normal 0 25 MHz High Speed 0 50 MHz Normal 10 ns High Speed 7 ns Normal 10 ns High Speed 7 ns Normal 5 ns High Speed 6 ns Normal 5 ns High Speed 2 ns 7.33 High Speed 2.5 ns ns 21.7.2.2. SDIO Protocol Timing - Default Speed Mode (3.3V) 21.7.2.3. SDIO Protocol Timing - High Speed Mode (3.3V) PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 30 of 53 DATE 11.07.2014 21.7.2.4. SDIO Timing Data - SDR12, SDR25, SDR50 Modes (1.8V) Symbol Parameter Condition Min. Typ. Max. fPP Clock frequency SDR12 / SDR25 / SDR50 25 TIS Input setup time SDR12 / SDR25 / SDR50 3 ns TIH Input hold time SDR12 / SDR25 / SDR50 0.8 ns TCLK Clock time SDR12 / SDR25 / SDR50 10 TCR , TCF Rise time, fall time TCR , TCF < 2 ns (max) at 100 MHz CCARD = 10 pF TODLY TOH 100 Units MHz 40 ns SDR12 / SDR25 / SDR50 0.2 TCLK ns Output delay time, CL 30 pF SDR12 / SDR25 / SDR50 7.5 ns Output hold time, CL 15 pF SDR12 / SDR25 / SDR50 1.5 ns 21.7.2.5. SDIO Protocol Timing - SDR12, SDR25, SDR50 Modes (1.8V) 21.7.3. High-Speed UART Interface The UART Tx / Rx pins are powered from the VIO voltage supply internally connected to VDD = 3.3V. See Chapter 21.3 Digital Pin Characteristics for DC specification. 21.7.3.1. UART Baud Rates Supported Baud Rate 1200 2400 4800 9600 19200 38400 57600 76800 115200 230400 460800 500000 921600 1000000 1382400 1500000 1834200 2000000 2100000 2764800 3000000 3250000 3692300 4000000 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT No. DS-9055-2400-102 PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 PANASONIC'S CODE ENWF9101x1yF REV. 0.1 PAGE 31 of 53 DATE 11.07.2014 21.8. PERIPHERAL INTERFACE SPECIFICATION 21.8.1. GPIO The GPIO pins are powered from the VIO voltage supply internally connected to VDD = 3.3V. See Chapter 21.3 Digital Pin Characteristics for DC specification. GPIO Function GPIO Pin GPIO[1] Port 1 GPIO[4] Port 4 GPIO[16] Port 16 GPIO[17] Port 17 GPIO[18] Port 18 Pin LED0 GPIO4 HOST_WAKEUP LED1 CHIP_WAKEUP Input YES YES YES YES YES Output YES YES YES YES YES Chip-to-Host wake-up LED Mode Bluetooth Host-to-Chip wake-up NO YES NO General Purpose Function by firmware LED Mode WLAN LED Output YES NO The basic function of the GPIOs are set by firmware default, but can be reconfigured by software. 21.8.1. LED Mode of LED0 and LED1 The GPIO pin for LED Mode is powered from the VIO voltage supply internally connected to VDD = 3.3V. See Chapter 21.3 Digital Pin Characteristics for DC specification. Symbol Parameter Condition IOH Switching current high Tristate on pin (requires pull-up on board) IOL Switching current low @ 0.4V Min. Typ. Max. Units Tristate when driving high mA 10 mA 31 The LED Mode is independently selectable for the pin LED0 (Port1) and LED1 (Port17). PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 22. No. DS-9055-2400-102 PRODUCT SPECIFICATION PANASONIC'S CODE ENWF9101x1yF REV. 0.1 PAGE 32 of 53 DATE 11.07.2014 RF ELECTRICAL CHARACTERISTICS 22.1. WLAN RADIO SPECIFICATION Parameter Operation mode Specification IEEE 802.11 / IEEE 802.11b Standard Conformance IEEE 802.11g IEEE 802.11n Modulation IEEE 802.11b DSSS / CCK IEEE 802.11g OFDM IEEE 802.11n OFDM @ MCS0~15 and MCS32 (duplicate 6 Mbps) IEEE 802.11 1, 2 Mbps @ DSSS IEEE 802.11b 5.5, 11 Mbps @ DSSS / CCK IEEE 802.11g 6, 9, 12, 18, 24, 36, 48, 54 Mbps Physical layer data rates LGI 6.5, 13, 19.5, 26, 39, 52, 58.5, 65 Mbps SGI 7.2, 14.4, 21.7, 28.9, 43.3, 57.8, 65, 72.2 Mbps LGI 13.5, 27, 40.5, 54, 81, 108, 121.5, 135 Mbps SGI 15, 30, 45, 60, 90, 120, 135, 150 Mbps LGI 13, 26, 39, 52, 78, 104, 117, 130 Mbps SGI 14.4, 28.9, 43.3, 57.8, 86.7, 115.6, 130, 144.4 Mbps LGI 27, 54, 81, 108, 162, 216, 243, 270 Mbps SGI 30, 60, 90, 120, 180, 240, 270, 300 Mbps HT20 MCS0~7 HT40 Supported data rates IEEE 802.11n HT20 MCS8~15 HT40 MCS32 Duplicate 6 Mbps Supported bandwidth IEEE 802.11n 20, 40 MHz (BW) Supported channel mode operation IEEE 802.11n 20 MHz BW / channel, 40 MHz BW / channel, upper / lower 20 MHz BW @ 40 MHz channel, 20 MHz duplicate legacy BW @ 40 MHz channel Supported Guard Interval IEEE 802.11n 400 ns (SGI), 800 ns (LGI) Supported Spatial Streams IEEE 802.11n 2x2 MIMO IEEE 802.11g 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13 Supported channel 2.4GHz 20 MHz Channel 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13 40 MHz Channel 1-5, 2-6, 3-7, 4-8, 5-9, 6-10, 7-11 IEEE 802.11n PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 33 of 53 DATE 11.07.2014 22.2. WLAN RF CHARACTERISTICS 22.2.1. RF Characteristics for IEEE 802.11b Assume VDD = 3.3V, Tamb = 25C if nothing else stated 50 Ohm terminal load connected to the RF connector Parameter Condition RF frequency range Min. Typ. Max. Units 2400 2500 MHz Carrier frequency tolerance -25 +25 ppm Transmit output power +16 +20 dBm fC 11 MHz -30 dBr fC 22 MHz -50 +18 Spectrum mask Power-on / Power-down ramp RF Carrier suppression Error Vector Magnitude (EVM) Peak 2 s -15 dB 35 % 1 Mbps (DSSS) FER 8% -98 -86 dBm 2 Mbps (DSSS) FER 8% -95 -83 dBm 5.5 Mbps (CCK) FER 8% -91 -79 dBm 11 Mbps (CCK) FER 8% -88 -76 dBm Minimum Receive Sensitivity Maximum Input Level FER 8% -10 dBm Adjacent Channel Rejection FER 8% 35 dB PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 34 of 53 DATE 11.07.2014 22.2.2. RF Characteristics for IEEE 802.11g Assume VDD = 3.3V, Tamb = 25C if nothing else stated 50 Ohm terminal load connected to the RF connector Parameter Condition RF frequency range Min. Typ. Max. Units 2400 2500 MHz Carrier frequency tolerance -20 +20 ppm Transmit output power +12 +16 dBm fC 11 MHz -20 dBr fC 20 MHz -28 dBr fC 30 MHz -40 dBr -15 dB +2 dB BPSK, CR 1/2 (6 Mbps) -5 dB BPSK, CR 3/4 (9 Mbps) -8 dB QPSK, CR 1/2 (12 Mbps) -10 dB QPSK, CR 3/4 (18 Mbps) -13 dB 16-QAM, CR 1/2 (24 Mbps) -16 dB 16-QAM, CR 3/4 (36 Mbps) -19 dB 64-QAM, CR 2/3 (48 Mbps) -22 dB 64-QAM, CR 3/4 (54 Mbps) -25 dB Spectrum mask +14 Transmitter center frequency leakage Transmitter Spectral Flatness -2 Constellation Error (EVM) BPSK, CR 1/2 (6 Mbps) PER 10% -93 -82 dBm BPSK, CR 3/4 (9 Mbps) PER 10% -92 -81 dBm QPSK, CR 1/2 (12 Mbps) PER 10% -90 -79 dBm QPSK, CR 3/4 (18 Mbps) PER 10% -88 -77 dBm 16-QAM, CR 1/2 (24 Mbps) PER 10% -85 -74 dBm 16-QAM, CR 3/4 (36 Mbps) PER 10% -81 -70 dBm 64-QAM, CR 2/3 (48 Mbps) PER 10% -77 -66 dBm 64-QAM, CR 3/4 (54 Mbps) PER 10% -76 -65 dBm -20 dBm Minimum Receive Sensitivity PER 10% Maximum Input Level BPSK, CR 1/2 (6 Mbps) PER 10% 16 dB 64-QAM, CR 3/4 (54 Mbps) PER 10% -1 dB Adjacent channel rejection PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 35 of 53 DATE 11.07.2014 22.2.3. RF Characteristics for IEEE 802.11n (BW 20 MHz) Assume VDD = 3.3V, Tamb = 25C if nothing else stated 50 Ohm terminal load connected to the RF connector Parameter Condition RF frequency range Min. Typ. Max. Units 2400 2500 MHz Carrier frequency tolerance -20 +20 ppm Transmit output power 11 15 dBm fC 11 MHz -20 dBr fC 20 MHz -28 dBr fC 30 MHz -45 dBr -15 dB +2 dB BPSK, CR 1/2 -5 dB QPSK, CR 1/2 -10 dB QPSK, CR 3/4 -13 dB 16-QAM, CR 1/2 -16 dB 16-QAM, CR 3/4 -19 dB 64-QAM, CR 2/3 -22 dB 64-QAM, CR 3/4 -25 dB 64-QAM, CR 5/6 -28 dB Spectrum mask 13 Transmitter center frequency leakage Transmitter Spectral Flatness -2 Constellation Error (EVM) Minimum Receive Sensitivity 6.5 Mbps (MCS0) PER 10% -92 -82 dBm 13 Mbps (MCS1) PER 10% -89 -79 dBm 19.5 Mbps (MCS2) PER 10% -87 -77 dBm 26 Mbps (MCS3) PER 10% -84 -74 dBm 39 Mbps (MCS4) PER 10% -80 -70 dBm 52 Mbps (MCS5) PER 10% -76 -66 dBm 58.5 Mbps (MCS6) PER 10% -75 -65 dBm 65 Mbps (MCS7) PER 10% -74 -64 dBm -20 dBm 12 PER 10% Maximum Input Level Adjacent channel rejection 13 65 Mbps (MCS7) PER 10% -2 12 The Minimum Sensitivity levels apply only to non-STBC modes, MCS 0~15, 800 ns LGI and BCC. 13 The Adjacent Channel Rejection levels apply only to non-STBC modes, MCS 0~15, 800 ns LGI and BCC. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH dB www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 36 of 53 DATE 11.07.2014 22.2.4. RF Characteristics for IEEE 802.11n (BW 40 MHz) Assume VDD = 3.3V, Tamb = 25C if nothing else stated 50 Ohm terminal load connected to the RF connector Condition Parameter RF frequency range Min. Typ. Max. Units 2400 2500 MHz Carrier frequency tolerance -20 +20 ppm Transmit output power 11 15 dBm fC 21 MHz -20 dBr fC 40 MHz -28 dBr fC 60 MHz -45 dBr -15 dB +2 dB BPSK, CR 1/2 -5 dB QPSK, CR 1/2 -10 dB QPSK, CR 3/4 -13 dB 16-QAM, CR 1/2 -16 dB 16-QAM, CR 3/4 -19 dB 64-QAM, CR 2/3 -22 dB 64-QAM, CR 3/4 -25 dB 64-QAM, CR 5/6 -28 dB Spectrum mask 13 Transmitter center frequency leakage Transmitter Spectral Flatness -2 Constellation Error (EVM) 13.5 Mbps (MCS0) PER 10% -89 -79 dBm 27 Mbps (MCS1) PER 10% -86 -76 dBm 40.5 Mbps (MCS2) PER 10% -84 -74 dBm 54 Mbps (MCS3) PER 10% -81 -71 dBm 81 Mbps (MCS4) PER 10% -77 -67 dBm 108 Mbps (MCS5) PER 10% -73 -63 dBm 121.5 Mbps (MCS6) PER 10% -72 -62 dBm 135 Mbps (MCS7) PER 10% -71 -61 dBm -20 dBm Minimum Receive Sensitivity 12 PER 10% Maximum Input Level Adjacent channel rejection 13 135 Mbps (MCS7) PER 10% PANASONIC INDUSTRIAL DEVICES EUROPE GMBH -2 dB www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 37 of 53 DATE 11.07.2014 22.3. BLUETOOTH RF CHARACTERISTICS Assume VDD = 3.3V, Tamb = 25C if nothing else stated 50 Ohm terminal load connected to the RF connector Parameter Condition RF frequency range Min. Typ. 2400 Channel Spacing BDR, EDR RSSI range Resolution = 1 dB Output Power Class BDR, EDR Output Power BDR Minimum Receive Sensitivity BDR Spurious Emission Conducted measurement with a 50- dual-ended load. Complies with EN 300 328, EN 300 440 class 2, FCC CFR47, Part 15 and ARIB STD-T-66 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH Max. 2500 1/2 -90 Units MHz MHz 0 dBm Class 1.5 8 dBm -70 dBm dBm www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 23. PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 38 of 53 DATE 11.07.2014 SOLDERING TEMPERATURE-TIME PROFILE (FOR REFLOW SOLDERING) 23.1. FOR LEAD SOLDER 10 1s Recommended temp. profile for reflow soldering 30 +20/-10s 235C max. Temp.[C] 220 5C 200C 150 10C 90 30s Time [s] 23.2. FOR LEADFREE SOLDER Our used temp. profile for reflow soldering Temp.[C] 30 +20/-10s 230C -250C max. 220C 150C - 190C 90 30s Time [s] Reflow permissible cycle: 2 Opposite side reflow is prohibited due to module weight. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 39 of 53 DATE 11.07.2014 PAN9055 / PAN9045 MODULE DIMENSION No. Item Dimension Tolerance 1 Width 13.50 0.20 2 Length 26.00 0.20 3 Height 2.40 0.20 13 Remark With case 26 ,50 2,40 24. PRODUCT SPECIFICATION PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 25. PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 40 of 53 DATE 11.07.2014 PAN9055 / PAN9045 FOOTPRINT OF THE MODULE All dimensions are in millimeters. The outer dimensions have a tolerance of 0.2mm. Top view, Application PCB PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 26. No. DS-9055-2400-102 PRODUCT SPECIFICATION PANASONIC'S CODE ENWF9101x1yF REV. 0.1 PAGE 41 of 53 DATE 11.07.2014 CASE MARKING TBP No. Remark 1 Marking for Pin 1 (Circle 0,15 mm) 2 2D-Code, for internal usage only and can be change without any notice 3 Marking definition see below 26.1. EXAMPLE FOR MARKING P E Y S M M A N Y N A A N W W S C C 9 F W N M M 0 9 D S A A 5 1 L N C C 5 0 L S M M H W / S W 1 x 1 y F E S N A C M A C A C M A C 26.2. MARKING DEFINITION (1) Pin1 marking (2) 2D code (Serial number) (3) Marking: PAN9055 (Model Name), HW/SW (Hardware/Software version) ES (Engineering Sample marking) ENWF9101x1yF (Part Number, refer to chapter 32. Ordering Information) Lot code (YearYear, WeekWeek, Day, LotLot) Serial Number (8 digits) WLAN MAC address (12 digits) Bluetooth MAC address (12 digits) Note: For available Versions, refer to [1] PAN9055 and PAN9045 Design-Guide. and chapter 32. Ordering Information. 27. MECHANICAL REQUIREMENTS No. Item 1 Solderability 2 Resistance to soldering heat Limit Condition More than 75% of the soldering area shall be coated by solder It shall be satisfied electrical requirements and not be mechanical damage Reflow soldering with recommendable temperature profile PANASONIC INDUSTRIAL DEVICES EUROPE GMBH See chapter 23.2 www.pideu.panasonic.de CLASSIFICATION SUBJECT WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 28. No. DS-9055-2400-102 PRODUCT SPECIFICATION PANASONIC'S CODE ENWF9101x1yF REV. 0.1 PAGE 42 of 53 DATE 11.07.2014 DEVELOPMENT OF APPLICATIONS For development support please refer to [1] PAN9055 and PAN9045 Design-Guide. 29. RELIABILITY TESTS The measurement should be done after being exposed to room temperature and humidity for 1 hour. 30. No. Item Limit Condition 1 Vibration test Electrical parameter should be in specification a) Freq.:10~50Hz,Amplitude:1.5mm a) 20min. / cycle,1hrs. each of XYZ axis b) Freq.:30~100Hz, 6G b) 20min. / cycle,1hrs. each of XYZ axis 2 Shock test the same as above Dropped onto hard wood from height of 50cm for 3 times 3 Heat cycle test the same as above -40C for 30min. and +85C for 30min.; each temperature 300 cycles 4 Moisture test the same as above +60C, 90% RH, 300h 5 Low temp. test the same as above -40C, 300h 6 High temp. test the same as above +85C, 300h CAUTIONS Failure to follow the guidelines set forth in this document may result in degrading of the product's functions and damage to the product. 30.1. DESIGN NOTES (1) (2) (3) (4) (5) (6) (7) Follow the conditions written in this specification, especially the control signals of this module. The supply voltage has to be free of AC ripple voltage (for example from a battery or a low noise regulator output). For noisy supply voltages, provide a decoupling circuit (for example a ferrite in series connection and a bypass capacitor to ground of at least 47uF directly at the module). This product should not be mechanically stressed when installed. Keep this product away from heat. Heat is the major cause of decreasing the life of these products. Avoid assembly and use of the target equipment in conditions where the products' temperature may exceed the maximum tolerance. The supply voltage should not be exceedingly high or reversed. It should not carry noise and/or spikes. Keep this product away from other high frequency circuits. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 43 of 53 DATE 11.07.2014 30.2. INSTALLATION NOTES (1) Reflow soldering is possible twice based on the conditions in chapter 15. Set up the temperature at the soldering portion of this product according to this reflow profile. (2) Carefully position the products so that their heat will not burn into printed circuit boards or affect the other components that are susceptible to heat. (3) Carefully locate these products so that their temperatures will not increase due to the effects of heat generated by neighboring components. (4) If a vinyl-covered wire comes into contact with the products, then the cover will melt and generate toxic gas, damaging the insulation. Never allow contact between the cover and these products to occur. (5) This product should not be mechanically stressed or vibrated when reflowed. (6) To repair the board by hand soldering, follow the conditions set forth in this chapter. (7) Do not wash this product. (8) Refer to the recommended pattern when designing a board. (9) Pressing on parts of the metal cover or fastening objects to the metal will cause damage to the unit. (10) For more details on LGA (Land Grid Array) soldering processes refer to the application note. 30.3. USAGE CONDITIONS NOTES (1) (2) (3) (4) (5) (6) (7) Take measures to protect the unit against static electricity. If pulses or other transient loads (a large load applied in a short time) are applied to the products, check and evaluate their operation befor assembly on the final products. Do not use dropped products. Do not touch, damage or soil the pins. Follow the recommended condition ratings about the power supply applied to this product. Electrode peeling strength: Do not add pressure of more than 4.9N when soldered on PCB. Pressing on parts of the metal cover or fastening objects to the metal cover will cause damage. These products are intended for general purpose and standard use in general electronic equipment, such as home appliances, office equipment, information and communication equipment. 30.4. STORAGE NOTES (1) (2) (3) (4) (5) The module should not be stressed mechanically during storage. Do not store these products in the following conditions or the performance characteristics of the product, such as RF performance will be adversely affected: Storage in salty air or in an environment with a high concentration of corrosive gas, such as Cl2, H2S, NH3, SO2, or NOX Storage in direct sunlight Storage in an environment where the temperature may be outside the range of 5C to 35C range, or where the humidity may be outside the 45 to 85% range. Storage of the products for more than one year after the date of delivery Storage period: Please check the adhesive strength of the embossed tape and soldering after 6 months of storage. Keep this product away from water, poisonous gas and corrosive gas. This product should not be stressed or shocked when transported. Follow the specification when stacking packed crates (max. 10). PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 44 of 53 DATE 11.07.2014 30.5. SAFETY CAUTIONS These specifications are intended to preserve the quality assurance of products and individual components. Before use, check and evaluate the operation when mounted on your products. Abide by these specifications, without deviation when using the products. These products may short-circuit. If electrical shocks, smoke, fire, and/or accidents involving human life are anticipated when a short circuit occurs, then provide the following failsafe functions, as a minimum. (1) Ensure the safety of the whole system by installing a protection circuit and a protection device. (2) Ensure the safety of the whole system by installing a redundant circuit or another system to prevent a single fault causing an unsafe status. 30.6. OTHER CAUTIONS (1) (2) (3) (4) (5) (6) (7) This specification sheet is copyrighted. Please do not disclose it to a third party. Please do not use the products for other purposes than those listed. Be sure to provide an appropriate fail-safe function on your product to prevent an additional damage that may be caused by the abnormal function or the failure of the product. This product has been manufactured without any ozone chemical controlled under the Montreal Protocol. These products are not intended for other uses, other than under the special conditions shown below. Before using these products under such special conditions, check their performance and reliability under the said special conditions carefully to determine whether or not they can be used in such a manner. In liquid, such as water, salt water, oil, alkali, or organic solvent, or in places where liquid may splash. In direct sunlight, outdoors, or in a dusty environment In an environment where condensation occurs. In an environment with a high concentration of harmful gas (e.g. salty air, HCl, Cl2, SO2, H2S, NH3, and NOX) If an abnormal voltage is applied due to a problem occurring in other components or circuits, replace these products with new products because they may not be able to provide normal performance even if their electronic characteristics and appearances appear satisfactory. When you have any question or uncertainty, contact Panasonic. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 31. PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 45 of 53 DATE 11.07.2014 PACKAGING If the product has mass production status, indicated in chapter 3, we will deliver the module in the package which are described below. 31.1. PAN9055 / PAN9045 TAPE DIMENSION TBP 31.2. PACKING IN TAPE Empty spaces in component packed area shall be less than two per reel and those spaces shall not be consecutive. Top cover tape shall not be found on reel holes and shall not stick out from reel. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 46 of 53 DATE 11.07.2014 31.3. COMPONENT DIRECTION 31.4. REEL DIMENSION PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT No. DS-9055-2400-102 PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 PANASONIC'S CODE ENWF9101x1yF REV. 0.1 PAGE 47 of 53 DATE 11.07.2014 31.5. LABEL FOR PACKAGE The picture shows an example from similar product. (1T) (1P) Lot code [YYWWDLL] Example from above: YY year printed 08 WW normal calendar week printed 01 D day printed 5 (Friday) L line identifier, if more as one printed 1 L lot identifier per day printed 1 Customer Order Code, if any, otherwise company name will be printed (2P) Panasonic Order Code: ENWF9101x1yF (9D) Date code as [YYWW] (Q) Quantity [XXXX], variable max. 1500 (HW/SW) Hardware /Software Release Hardware 01 Indicates the HW revision. Software 01 Indicates the SW revision. 31.6. TOTAL PACKAGE moisture-sensitive print (already exist on barrier bag) barcode label barrier bag sealed desiccant 1) 2) moisture indicator barcode label 1) quantity of desiccant according to calculation 2) optional: desiccant placed into the corner of the barrier bag inner carton box size 340 x 340 x 41 mm PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 32. PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 48 of 53 DATE 11.07.2014 ORDERING INFORMATION Ordering part number ENWF9101A1JF (2) ENWF9101C1JF (2) ENWF9101A1EF (2) ENWF9101C1EF (2) Description PAN9055 WLAN IEEE 802.11 b/g/n 2.4GHz Radio Module with ceramic chip-antenna COMMERCIAL GRADE PAN9045 WLAN IEEE 802.11 b/g/n 2.4GHz Radio Module with 50 bottom pad COMMERCIAL GRADE PAN9055 WLAN IEEE 802.11 b/g/n 2.4GHz Radio Module with ceramic chip-antenna EXTENDED GRADE PAN9045 WLAN IEEE 802.11 b/g/n 2.4GHz Radio Module with 50 bottom pad EXTENDED GRADE MOQ (1) ES ES ES ES Notes: (1) Abbreviation for Minimum Order Quantity (MOQ). The standard MOQ for mass production is 1500 pieces, fewer only on customer demand. Samples for evaluation can be delivered at any quantity via the distribution channels. (2) Samples are available on customer demand 32.1. INFORMATION REGARDING SOFTWARE VERSIONS ENWF9101A1JF / ENWF9101C1JF / ENWF9101A1EF / ENWF9101C1EF: The modules will be delivered without any WLAN / BT Firmware but including calibration data. The WLAN / BT SoC Firmware and HOST Driver-Firmware Interface software modules taking place on the customers HOST processor and need to be programmed on their own production process. For details refer to the design guide. 33. ROHS DECLARATION Declaration of environmental compatibility for supplied products: Hereby we declare to our best present knowledge based on declaration of our suppliers that this product does not contain the following substances which are banned by Directive 2002/95/EC (RoHS) or contains a maximum concentration of 0.1% by weight in homogeneous materials for Lead and lead compounds Mercury and mercury compounds Chromium (VI) PBB (polybrominated biphenyl) category PBDE (polybrominated biphenyl ether) category And a maximum concentration of 0.01% by weight in homogeneous materials for Cadmium and cadmium compounds PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 34. PRODUCT SPECIFICATION PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 49 of 53 DATE 11.07.2014 REGULATORY INFORMATION 34.1. FCC FOR US 34.1.1. FCC Notice The device PAN9055, including the ceramic antenna (ENWF9101A1JF and ENWF9101A1EF) and PAN9045 SMD type (ENWF9101C1JF and ENWF9101C1EF), including with the antennas, which are listed in 34.1.5, complies with Part 15 of the FCC Rules. The device meets the requirements for modular transmitter approval as detailed in FCC public Notice DA00-1407.transmitter Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. The FCC identifier is FCC ID: T7V-9055 TBC. 34.1.2. Caution The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Panasonic Industrial Devices Europe GmbH may void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help 34.1.3. Labeling Requirements The Original Equipment Manufacturer (OEM) must ensure that FCC labelling requirements are met. This includes a clearly visible label (laser marking) on the outside of the OEM enclosure specifying the appropriate Panasonic FCC identifier for this product as well as the FCC Notice above. The FCC identifier is FCC ID: T7V-9055 TBC. This FCC identifier is valid for all PAN9055 modules, for details, see the Chapter 32. Ordering Information. In any case the end product must be labelled exterior with "Contains FCC ID: T7V-9055" TBC PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 50 of 53 DATE 11.07.2014 34.1.4. Antenna Warning The related part number for this device are ENWF9101C1JF and ENWF9101C1EF (PAN9045 with SMD pad). For details, see the Chapter 32. Ordering Information. These devices are tested with a standard SMA connector and with the antennas listed below. When integrated in the OEMs product, these fixed antennas require installation preventing end-users from replacing them with non-approved antennas. Any antenna not in the following table must be tested to comply with FCC Section 15.203 for unique antenna connectors and Section 15.247 for emissions. The FCC identifier for this device with the antenna listed in item 1 is the same (FCC ID: T7V-9055 TBC). 34.1.5. Approved Antenna List Note: We are able to qualify your antenna and will add to this list as that process is completed. Item Part Number Manufacturer Frequency Band Type Gain (dBi) 1 ANT2012LL13R2400A Taiyo Yuden 2.4GHz Chip-Antenna +2.72 34.1.6. RF Exposure PAN9055 To comply with FCC RF Exposure requirements, the Original Equipment Manufacturer (OEM) must ensure that the approved antenna in the previous table must be installed. The preceding statement must be included as a CAUTION statement in manuals for products operating with the approved antennas in the previous table to alert users on FCC RF Exposure compliance. Any notification to the end user of installation or removal instructions about the integrated radio module is not allowed. The radiated output power of PAN9055 with mounted ceramic chip antenna (FCC ID: T7V-9055 TBC) is far below the FCC radio frequency exposure limits. Nevertheless, the PAN9055 shall be used in such a manner that the potential for human contact during normal operation is minimized. End users may not be provided with the module installation instructions. OEM integrators and end users must be provided with transmitter operating conditions for satisfying RF exposure compliance. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 51 of 53 DATE 11.07.2014 34.2. INDUSTRY CANADA CERTIFICATION PAN9055 is licensed to meet the regulatory requirements of Industry Canada (IC), license: IC: 216Q-9055 TBC Manufacturers of mobile, fixed or portable devices incorporating this module are advised to clarify any regulatory questions and ensure compliance for SAR and/or RF exposure limits. Users can obtain Canadian information on RF exposure and compliance from www.ic.gc.ca. This device has been designed to operate with the antennas listed in Table 34.1.5 above, having a maximum gain of 2.72 dBi. Antennas not included in this list or having a gain greater than 2.72 dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. The antenna used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Due to the model size the IC identifier is displayed in the installation instruction only and can not be displayed on the modules label due to the limited size. 34.2.1. IC Notice The device PAN9055, for details refer to Chapter 32, including the antennas, which are listed in 34.1.5, complies with Canada RSS-GEN Rules. The device meets the requirements for modular transmitter approval as detailed in RSS-GEN. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 34.2.2. Labeling Requirements The Original Equipment Manufacturer (OEM) must ensure that IC labelling requirements are met. This includes a clearly visible label on the outside of the OEM enclosure specifying the appropriate Panasonic IC identifier for this product as well as the IC Notice above. The IC identifier is: 216Q-9055 TBC. This IC identifier is valid for all PAN9055 modules, for details, see the Chapter 32. Ordering Information. In any case the end product must be labelled exterior with "Contains IC: 216Q-9055" TBC Les fabricants d'equipements (OEM) doivent s'assurer que les obligations d'etiquetage du produit final sont remplies. Ces obligations incluent une etiquette clairement visible a l'exterieur de l'emballage externe, comportant l'identifiant IC du module Panasonic inclus, ainsi que la notification ci-dessus. Les identifiants IC sont: IC: 216Q-9055 TBC Ces identifiants sont valides pour tous les modules PAN9055 (Chapter 32. Ordering Information). Dans tous les cas les produits finaux doivent indiquer sur leur emballage externe une des mentions suivantes: "Contient IC: 216Q-9055" TBC PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 52 of 53 DATE 11.07.2014 34.3. EUROPEAN R&TTE DECLARATION OF CONFORMITY All modules described in this data sheet comply to the standards according R&TTE article: 3.1a Safety/Health: EN60950-1:2006+A11:2009+A1:2010+A12:2011+AC:2011 EN62311:2008; EN 62479:2010 3.1b EMC: EN 301 489-17 V2.2.1:2012-09 3.2 Radio: EN 300 328 V1.8.1:2012-06 As a result of the conformity assessment procedure described in Annex III of the Directive 1999/5/EC, the end-customer equipment should be labelled as follows: The end-customer has to assure that the device has a distance of more the 20cm from the human body under all circumstances. The end-customer equipment must meet the actual Safety/Health requirements according R&TTE. PAN9055 and their versions in the specified reference design can be used in the following countries: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Netherland, the United Kingdom, Switzerland, and Norway. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN + BT4.0 RADIO MODULE CUSTOMER'S CODE PAN9055 / PAN9045 35. PANASONIC'S CODE ENWF9101x1yF No. DS-9055-2400-102 REV. 0.1 PAGE 53 of 53 DATE 11.07.2014 GENERAL INFORMATION (c) Panasonic Industrial Devices Europe GmbH 2014. All rights reserved. This product description does not lodge the claim to be complete and free of mistakes. Please contact the related product manager in every case. If we deliver ES samples to the customer, these samples have the status Engineering Samples. This means, the design of this product is not yet concluded. Engineering Samples may be partially or fully functional, and there may be differences to be published Data Sheet. Engineering Samples are not qualified and are not to be used for reliability testing or series production. Disclaimer: Customer acknowledges that samples may deviate from the Data Sheet and may bear defects due to their status of development and the lack of qualification mentioned above. Panasonic rejects any liability or product warranty for Engineering Samples. In particular, Panasonic disclaims liability for damages caused by the use of the Engineering Sample other than for Evaluation Purposes, particularly the installation or integration in another product to be sold by Customer, deviation or lapse in function of Engineering Sample, improper use of Engineering Samples. Panasonic Industrial Devices Europe GmbH disclaimes any liability for consequential and incidental damages. In case of any questions, please contact your local sales partner or the related product manager. 36. LIFE SUPPORT POLICY This Panasonic Industrial Devices Europe GmbH product is not designed for use in life support appliances, devices, or systems where malfunction can reasonably be expected to result in a significant personal injury to the user, or as a critical component in any life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. Customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Panasonic Industrial Devices Europe GmbH for any damages resulting. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de