Film Capacitors Metallized Polyester Film Capacitors (MKT) Series/Type: B32232 Date: May 2009 The following products presented in this data sheet are being withdrawn. Ordering Code B32232A6154J189 B32232A6154J000 B32232A6104K189 Substitute Product Date of Withdrawal 2012-08-24 2012-08-24 2012-08-24 Deadline Last Orders 2012-11-30 2012-11-30 2012-11-30 Last Shipments 2013-02-28 2013-02-28 2013-02-28 (c) EPCOS AG 2009. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. Ordering Code B32232A6104K000 B32232A6104J189 B32232A6104J000 B32232A3684K189 B32232A3684K000 B32232A3684J189 B32232A3684J000 B32232A3474K189 B32232A3474K000 B32232A3474J189 B32232A3474J000 B32232A3334K189 B32232A3334K000 B32232A3334J189 B32232A3334J000 B32232A3225K189 B32232A3225K000 B32232A3225J189 B32232A3225J000 B32232A3224K189 B32232A3224K000 B32232A3224J189 B32232A3224J000 B32232A3155K189 B32232A3155K000 B32232A3155J189 B32232A3155J000 B32232A3154K189 B32232A3154K000 B32232A3154J189 B32232A3154J000 B32232A3105K189 B32232A3105K000 B32232A3105J189 B32232A3105J000 B32232A3104K189 B32232A3104K000 B32232A3104J189 Substitute Product Date of Withdrawal 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 Deadline Last Orders 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 Last Shipments 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 Ordering Code B32232A3104J000 B32232A1684K189 B32232A1684K000 B32232A1684J189 B32232A1684J000 B32232A1475K189 B32232A1475K000 B32232A1475J189 B32232A1475J000 B32232A1474K189 B32232A1474K000 B32232A1474J189 B32232A1474J000 B32232A1335K189 B32232A1335K000 B32232A1335J189 B32232A1335J000 B32232A1334K189 B32232A1334K000 B32232A1334J189 B32232A1334J000 B32232A1225K189 B32232A1225K000 B32232A1225J189 B32232A1225J000 B32232A1224K189 B32232A1224K000 B32232A1224J189 B32232A1224J000 B32232A1155K189 B32232A1155K000 B32232A1155J189 B32232A1155J000 B32232A1154K189 B32232A1154K000 B32232A1154J189 B32232A1154J000 B32232A1105K189 Substitute Product Date of Withdrawal 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 Deadline Last Orders 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 Last Shipments 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 Ordering Code B32232A1105K000 B32232A1105J189 B32232A1105J000 B32232A1104K189 B32232A1104K000 B32232A1104J189 B32232A1104J000 B32232A8683K189 B32232A8683K000 B32232A8683J189 B32232A8683J000 B32232A8474K000 B32232A8474J000 B32232A8473K189 B32232A8473K000 B32232A8473J189 B32232A8473J000 B32232A8334K189 B32232A8334K000 B32232A8334J189 B32232A8334J000 B32232A8333K189 B32232A8333K000 B32232A8333J189 B32232A8333J000 B32232A8224K189 B32232A8224K000 B32232A8224J189 B32232A8224J000 B32232A8154K189 B32232A8154K000 B32232A8154J189 B32232A8154J000 B32232A8104K189 B32232A8104K000 B32232A8104J189 B32232A8104J000 B32232A6684K189 Substitute Product Date of Withdrawal 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 Deadline Last Orders 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 Last Shipments 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 Ordering Code B32232A6684K000 B32232A6684J189 B32232A6684J000 B32232A6474K189 B32232A6474K000 B32232A6474J189 B32232A6474J000 B32232A6334K189 B32232A6334K000 B32232A6334J189 B32232A6334J000 B32232A6224K189 B32232A6224K000 B32232A6224J189 B32232A6224J000 B32232A6154K189 B32232A6154K000 Substitute Product Date of Withdrawal 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 2012-08-24 Deadline Last Orders 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 2012-11-30 Last Shipments 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 2013-02-28 For further information please contact your nearest EPCOS sales office, which will also support you in selecting a suitable substitute. The addresses of our worldwide sales network are presented at www.epcos.com/sales. Metallized polyester film capacitors (MKT) B32232 General purpose (wound) Typical applications Smoothing Filtering Dimensional drawing Climatic Max. operating temperature: 100 C Climatic category (IEC 60068-1): 40/100/21 Construction Dielectric: polyethylene terephthalate (polyester, PET) Cylindrical winding Insulating sleeve Face ends sealed with epoxy resin Dimensions in mm Diameter d 7.0 > 7.0 Terminals Central axial wire leads, lead-free tinned Marking Manufacturer, series number, rated capacitance (coded), capacitance tolerance (code letter), rated DC voltage. date of manufacture (coded) When bending leads take care to leave a clearance of 1 mm to the capacitor body. Delivery mode Bulk (untaped) Taped (reel) For notes on taping, refer to chapter "Taping and packing". Detail specification DIN 45910-112 Please read Cautions and warnings and Important notes at the end of this document. Lead diameter d1 0.6 0.8 Page 2 of 19 B32232 General purpose (wound) Overview of available types Type B32232 VR (V DC) 100 250 400 630 VRMS (V AC) 63 160 200 200 CR (F) 0.033 0.047 0.068 0.10 0.15 0.22 0.33 0.47 0.68 1.0 1.5 2.2 3.3 4.7 6.8 Please read Cautions and warnings and Important notes at the end of this document. Page 3 of 19 B32232 General purpose (wound) Ordering codes and packing units VR VRMS CR f 60 Hz V DC V AC F 100 63 0.10 0.15 0.22 0.33 0.47 0.68 1.0 1.5 2.2 3.3 4.7 6.8 250 160 0.10 0.15 0.22 0.33 0.47 0.68 1.0 1.5 2.2 3.3 4.7 6.8 400 200 0.10 0.15 0.22 0.33 0.47 0.68 1.0 Max. dimensions dxl mm 6.0 x 14.0 6.0 x 14.0 6.0 x 14.0 6.0 x 19.0 6.5 x 19.0 7.0 x 19.0 8.5 x 19.0 8.0 x 27.0 9.5 x 27.0 11.5 x 27.0 12.0 x 32.0 14.0 x 32.0 6.0 x 14.0 7.0 x 14.0 6.0 x 19.0 7.0 x 19.0 8.0 x 19.0 8.0 x 27.0 10.0 x 27.0 10.0 x 32.0 11.0 x 32.0 14.0 x 32.0 16.5 x 32.0 16.0 x 42.0 7.0 x 19.0 8.5 x 19.0 8.0 x 27.0 9.5 x 27.0 11.0 x 27.0 11.5 x 32.0 13.5 x 32.0 Ordering code (composition see below) B32232A1104+*** B32232A1154+*** B32232A1224+*** B32232A1334+*** B32232A1474+*** B32232A1684+*** B32232A1105+*** B32232A1155+*** B32232A1225+*** B32232A1335+*** B32232A1475+*** B32232A1685+*** B32232A3104+*** B32232A3154+*** B32232A3224+*** B32232A3334+*** B32232A3474+*** B32232A3684+*** B32232A3105+*** B32232A3155+*** B32232A3225+*** B32232A3335+*** B32232A3475+000 B32232A3685+000 B32232A6104+*** B32232A6154+*** B32232A6224+*** B32232A6334+*** B32232A6474+*** B32232A6684+*** B32232A6105+*** MOQ = Minimum Order Quantity, consisting of 4 packing units. Further E series and intermediate capacitance values on request. Composition of ordering code + = Capacitance tolerance code: K = 10% J = 5% Please read Cautions and warnings and Important notes at the end of this document. *** = Packaging code: 189 = Reel 000 = Untaped Page 4 of 19 Reel Untaped pcs./MOQ 4000 4000 4000 4000 4000 4000 4000 4000 3600 2000 2000 2000 4000 4000 4000 4000 4000 4000 2000 2000 2000 2000 4000 4000 4000 3200 2000 2000 2000 pcs./MOQ 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 1000 2000 2000 2000 2000 2000 2000 2000 2000 2000 1000 1000 800 2000 2000 2000 2000 2000 2000 2000 B32232 General purpose (wound) Ordering codes and packing units VR VRMS CR f 60 Hz V DC V AC F 630 200 0.033 0.047 0.068 0.10 0.15 0.22 0.33 0.47 0.68 1.0 Max. dimensions dxl mm 6.5 x 19.0 7.5 x 19.0 8.5 x 19.0 10.5 x 19.0 10.0 x 27.0 11.5 x 27.0 13.5 x 27.0 14.5 x 32.0 15.0 x 32.0 16.0 x 32.0 Ordering code (composition see below) B32232A8333+*** B32232A8473+*** B32232A8683+*** B32232A8104+*** B32232A8154+*** B32232A8224+*** B32232A8334+*** B32232A8474+000 B32232A8684+000 B32232A8105+000 MOQ = Minimum Order Quantity, consisting of 4 packing units. Further E series and intermediate capacitance values on request. Composition of ordering code + = Capacitance tolerance code: K = 10% J = 5% Please read Cautions and warnings and Important notes at the end of this document. *** = Packaging code: 189 = Reel 000 = Untaped Page 5 of 19 Reel Untaped pcs./MOQ 4000 4000 4000 2000 2000 2000 2000 pcs./MOQ 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 B32232 General purpose (wound) Technical data Operating temperature range Max. operating temperature Top,max Upper category temperature Tmax Lower category temperature Tmin Rated temperature TR Dissipation factor tan (in 10-3) at at 20 C (upper limit values) Insulation resistance Rins or time constant = CR Rins at 20 C, rel. humidity 65% (minimum as-delivered values) DC test voltage Category voltage VC (continuous operation with VDC or VAC at f 60 Hz) Operating voltage Vop for short operating periods (VDC or VAC at f 60 Hz) Damp heat test Limit values after damp heat test CR 47 nF 47 nF < CR 1 F CR > 1 F 1 kHz 10 10 10 kHz 20 25 VR CR 0.33 F 100 V DC 3750 M 250 V DC 7500 M 10 CR > 0.33 F 1250 s 2500 s 1.4 VR, 2 s TA (C) TA 85 85<TA100 TA (C) TA 100 AC voltage derating VC,RMS = VRMS VC,RMS=VRMS (165TA)/80 AC voltage (max. hours) Vop = 1.0 VC,RMS (1000 h) DC voltage derating VC = VR VC = VR (165TA)/80 DC voltage (max. hours) Vop = 1.25 VC (2000 h) 21 days/40 C/93% relative humidity Capacitance change C/C Dissipation factor change tan Insulation resistance Rins or time constant = CR Rins Please read Cautions and warnings and Important notes at the end of this document. +100 C +100 C 40 C +85 C Page 6 of 19 5% 5 10-3 (at 1 kHz) 7 10-3 (at 10 kHz) 20% of minimum as-delivered values B32232 General purpose (wound) Pulse handling capability "dV/dt" represents the maximum permissible voltage change per unit of time for non-sinusoidal voltages, expressed in V/s. "k0" represents the maximum permissible pulse characteristic of the waveform applied to the capacitor, expressed in V2/s. Note: The values of dV/dt and k0 provided below must not be exceeded in order to avoid damaging the capacitor. dV/dt values Length of capacitor VR VRMS V DC V AC 100 63 250 160 400 200 630 200 14 mm 19 mm 27 mm 32 mm 42 mm dV/dt in V/s 6 3 10 5 7 10 2 3 4 7 1.5 2.5 3 5 2 14 mm 19 mm 27 mm 32 mm 42 mm k0 in V2/s 1 200 5 000 600 2 500 5 600 12 500 400 1 500 3 200 8 800 300 1 250 2 400 6 300 1 000 k0 values Length of capacitor VR VRMS V DC V AC 100 63 250 160 400 200 630 200 Please read Cautions and warnings and Important notes at the end of this document. Page 7 of 19 B32232 General purpose (wound) Impedance Z versus frequency f (typical values) Permissible AC voltage VRMS versus frequency f Values can be obtained on request. In specific cases please provide a scaled voltage/ time graph and state operating conditions. Please read Cautions and warnings and Important notes at the end of this document. Page 8 of 19 B32232 General purpose (wound) Mounting guidelines 1 Soldering 1.1 Solderability of leads The solderability of terminal leads is tested to IEC 60068-2-20, test Ta, method 1. Before a solderability test is carried out, terminals are subjected to accelerated ageing (to IEC 60068-2-2, test Ba: 4 h exposure to dry heat at 155 C). Since the ageing temperature is far higher than the upper category temperature of the capacitors, the terminal wires should be cut off from the capacitor before the ageing procedure to prevent the solderability being impaired by the products of any capacitor decomposition that might occur. Solder bath temperature 235 5 C Soldering time 2.0 0.5 s Immersion depth 2.0 +0/0.5 mm from capacitor body or seating plane Evaluation criteria: Visual inspection Wetting of wire surface by new solder 90%, free-flowing solder 1.2 Resistance to soldering heat Resistance to soldering heat is tested to IEC 60068-2-20, test Tb, method 1A. Conditions: Series Solder bath temperature Soldering time MKT boxed (except 2.5 x 6.5 x 7.2 mm) 260 5 C coated uncoated (lead spacing > 10 mm) MFP MKP (lead spacing > 7.5 mm) MKT boxed (case 2.5 x 6.5 x 7.2 mm) MKP (lead spacing 7.5 mm) MKT uncoated (lead spacing 10 mm) insulated (B32559) Please read Cautions and warnings and Important notes at the end of this document. Page 9 of 19 10 1 s 5 1 s <4s recommended soldering profile for MKT uncoated (lead spacing 10 mm) and insulated (B32559) B32232 General purpose (wound) Immersion depth 2.0 +0/0.5 mm from capacitor body or seating plane Shield Heat-absorbing board, (1.5 0.5) mm thick, between capacitor body and liquid solder Evaluation criteria: Visual inspection C/C0 tan Please read Cautions and warnings and Important notes at the end of this document. No visible damage 2% for MKT/MKP/MFP 5% for EMI suppression capacitors As specified in sectional specification Page 10 of 19 B32232 General purpose (wound) 1.3 General notes on soldering Permissible heat exposure loads on film capacitors are primarily characterized by the upper category temperature Tmax. Long exposure to temperatures above this type-related temperature limit can lead to changes in the plastic dielectric and thus change irreversibly a capacitor's electrical characteristics. For short exposures (as in practical soldering processes) the heat load (and thus the possible effects on a capacitor) will also depend on other factors like: Pre-heating temperature and time Forced cooling immediately after soldering Terminal characteristics: diameter, length, thermal resistance, special configurations (e.g. crimping) Height of capacitor above solder bath Shadowing by neighboring components Additional heating due to heat dissipation by neighboring components Use of solder-resist coatings The overheating associated with some of these factors can usually be reduced by suitable countermeasures. For example, if a pre-heating step cannot be avoided, an additional or reinforced cooling process may possibly have to be included. EPCOS recommends the following conditions: Pre-heating with a maximum temperature of 110 C Temperature inside the capacitor should not exceed the following limits: MKP/MFP 110 C MKT 160 C When SMD components are used together with leaded ones, the leaded film capacitors should not pass into the SMD adhesive curing oven. The leaded components should be assembled after the SMD curing step. Leaded film capacitors are not suitable for reflow soldering. Uncoated capacitors For uncoated MKT capacitors with lead spacings 10 mm (B32560/B32561) the following measures are recommended: pre-heating to not more than 110 C in the preheater phase rapid cooling after soldering Please read Cautions and warnings and Important notes at the end of this document. Page 11 of 19 B32232 General purpose (wound) 2 Cleaning To determine whether the following solvents, often used to remove flux residues and other substances, are suitable for the capacitors described, refer to the table below: Type Ethanol, isopropanol, n-propanol MKT (uncoated) MKT, MKP, MFP (coated/boxed) Suitable n-propanol-water mixtures, water with surface tension-reducing tensides (neutral) Unsuitable Solvent from table A (see next page) Suitable Suitable Solvent from table B (see next page) In part suitable Unsuitable Even when suitable solvents are used, a reversible change of the electrical characteristics may occur in uncoated capacitors immediately after they are washed. Thus it is always recommended to dry the components (e.g. 4 h at 70 C) before they are subjected to subsequent electrical testing. Table A Manufacturers' designations for trifluoro-trichloro-ethane-based cleaning solvents (selection) Trifluoro-trichloroethane Freon TF Frigen 113 TR Arklone P Kaltron 113 MDR Flugene 113 Mixtures of trifluoro-trichloro-ethane with ethanol and isopropanol Freon TE 35; Freon TP 35; Freon TES Frigen 113 TR-E; Frigen 113 TR-P; Frigen TR-E 35 Arklone A; Arklone L; Arklone K Kaltron 113 MDA; Kaltron 113 MDI; Kaltron 113 MDI 35 Flugene 113 E; Flugene 113 IPA Manufacturer Du Pont Hoechst ICI Kali-Chemie Rhone-Progil Table B (worldwide banned substances) Manufacturers' designations for unsuitable cleaning solvents (selection) Mixtures of chlorinated hydrocarbons and ketones with fluorated hydrocarbons Freon TMC; Freon TA; Freon TC Arklone E Kaltron 113 MDD; Kaltron 113 MDK Flugene 113 CM Please read Cautions and warnings and Important notes at the end of this document. Page 12 of 19 Manufacturer Du Pont ICI Kali-Chemie Rhone-Progil B32232 General purpose (wound) 3 Embedding of capacitors in finished assemblies In many applications, finished circuit assemblies are embedded in plastic resins. In this case, both chemical and thermal influences of the embedding ("potting") and curing processes must be taken into account. Our experience has shown that the following potting materials can be recommended: non-flexible epoxy resins with acid-anhydride hardeners; chemically inert, non-conducting fillers; maximum curing temperature of 100 C. Caution: Consult us first if you wish to embed uncoated types! Please read Cautions and warnings and Important notes at the end of this document. Page 13 of 19 B32232 General purpose (wound) Cautions and warnings Do not exceed the upper category temperature (UCT). Do not apply any mechanical stress to the capacitor terminals. Avoid any compressive, tensile or flexural stress. Do not move the capacitor after it has been soldered to the PC board. Do not pick up the PC board by the soldered capacitor. Do not place the capacitor on a PC board whose PTH hole spacing differs from the specified lead spacing. Do not exceed the specified time or temperature limits during soldering. Avoid external energy inputs, such as fire or electricity. Avoid overload of the capacitors. The table below summarizes the safety instructions that must always be observed. A detailed description can be found in the relevant sections of the chapters "General technical information" and "Mounting guidelines". Topic Storage conditions Flammability Resistance to vibration Safety information Reference chapter "General technical information" Make sure that capacitors are stored within the 4.5 specified range of time, temperature and humidity "Storage conditions" conditions. Avoid external energy, such as fire or electricity 5.3 (passive flammability), avoid overload of the "Flammability" capacitors (active flammability) and consider the flammability of materials. Do not exceed the tested ability to withstand 5.2 vibration. The capacitors are tested to "Resistance to vibration" IEC 60068-2-6. EPCOS offers film capacitors specially designed for operation under more severe vibration regimes such as those found in automotive applications. Consult our catalog "Film Capacitors for Automotive Electronics". Please read Cautions and warnings and Important notes at the end of this document. Page 14 of 19 B32232 General purpose (wound) Topic Safety information Soldering Do not exceed the specified time or temperature limits during soldering. Cleaning Use only suitable solvents for cleaning capacitors. Embedding of When embedding finished circuit assemblies in capacitors in plastic resins, chemical and thermal influences finished assemblies must be taken into account. Caution: Consult us first, if you also wish to embed other uncoated component types! Please read Cautions and warnings and Important notes at the end of this document. Page 15 of 19 Reference chapter "Mounting guidelines" 1 "Soldering" 2 "Cleaning" 3 "Embedding of capacitors in finished assemblies" B32232 General purpose (wound) Symbols and terms Symbol C A C C CR C C/C C/CR dt t T tan V dV/dt V/t E ESL ESR f f1 f2 fr FD FT i IC English Heat transfer coefficient Temperature coefficient of capacitance Capacitor surface area Humidity coefficient of capacitance Capacitance Rated capacitance Absolute capacitance change Relative capacitance change (relative deviation of actual value) Capacitance tolerance (relative deviation from rated capacitance) Time differential Time interval Absolute temperature change (self-heating) Absolute change of dissipation factor Absolute voltage change Time differential of voltage function (rate of voltage rise) Voltage change per time interval Activation energy for diffusion Self-inductance Equivalent series resistance Frequency Frequency limit for reducing permissible AC voltage due to thermal limits German Warmeubergangszahl Temperaturkoeffizient der Kapazitat Kondensatoroberflache Feuchtekoeffizient der Kapazitat Kapazitat Nennkapazitat Absolute Kapazitatsanderung Relative Kapazitatsanderung (relative Abweichung vom Ist-Wert) Kapazitatstoleranz (relative Abweichung vom Nennwert) Differentielle Zeit Zeitintervall Absolute Temperaturanderung (Selbsterwarmung) Absolute Anderung des Verlustfaktors Absolute Spannungsanderung Differentielle Spannungsanderung (Spannungsflankensteilheit) Spannungsanderung pro Zeitintervall Aktivierungsenergie zur Diffusion Eigeninduktivitat Ersatz-Serienwiderstand Frequenz Grenzfrequenz fur thermisch bedingte Reduzierung der zulassigen Wechselspannung Frequency limit for reducing permissible Grenzfrequenz fur strombedingte AC voltage due to current limit Reduzierung der zulassigen Wechselspannung Resonant frequency Resonanzfrequenz Thermal acceleration factor for diffusion Therm. Beschleunigungsfaktor zur Diffusion Derating factor Deratingfaktor Current (peak) Stromspitze Category current (max. continuous Kategoriestrom (max. Dauerstrom) current) Please read Cautions and warnings and Important notes at the end of this document. Page 16 of 19 B32232 General purpose (wound) Symbol IRMS iz k0 LS 0 test Pdiss Pgen Q R R Ri Rins RP RS S t T tan tan D tan P tan S TA Tmax Tmin tOL Top TR Tref tSL VAC English (Sinusoidal) alternating current, root-mean-square value Capacitance drift Pulse characteristic Series inductance Failure rate Constant failure rate during useful service life Failure rate, determined by tests Dissipated power Generated power Heat energy Density of water vapor in air Universal molar constant for gases Ohmic resistance of discharge circuit Internal resistance Insulation resistance Parallel resistance Series resistance severity (humidity test) Time Temperature Time constant Dissipation factor Dielectric component of dissipation factor Parallel component of dissipation factor Series component of dissipation factor Ambient temperature Upper category temperature Lower category temperature Operating life at operating temperature and voltage Operating temperature Rated temperature Reference temperature Reference service life AC voltage Please read Cautions and warnings and Important notes at the end of this document. German (Sinusformiger) Wechselstrom Inkonstanz der Kapazitat Impulskennwert Serieninduktivitat Ausfallrate Konstante Ausfallrate in der Nutzungsphase Experimentell ermittelte Ausfallrate Abgegebene Verlustleistung Erzeugte Verlustleistung Warmeenergie Dichte von Wasserdampf in Luft Allg. Molarkonstante fur Gas Ohmscher Widerstand des Entladekreises Innenwiderstand Isolationswiderstand Parallelwiderstand Serienwiderstand Scharfegrad (Feuchtetest) Zeit Temperatur Zeitkonstante Verlustfaktor Dielektrischer Anteil des Verlustfaktors Parallelanteil des Verlfustfaktors Serienanteil des Verlustfaktors Umgebungstemperatur Obere Kategorietemperatur Untere Kategorietemperatur Betriebszeit bei Betriebstemperatur und -spannung Beriebstemperatur Nenntemperatur Referenztemperatur Referenz-Lebensdauer Wechselspannung Page 17 of 19 B32232 General purpose (wound) Symbol VC VC,RMS English Category voltage Category AC voltage VCD Vch VDC VFB Vi Vo Vop Vp Vpp VR Corona-discharge onset voltage Charging voltage DC voltage Fly-back capacitor voltage Input voltage Output voltage Operating voltage Peak pulse voltage Peak-to-peak voltage Impedance Rated voltage Amplitude of rated AC voltage R VRMS German Kategoriespannung (Sinusformige) Kategorie-Wechselspannung Teilentlade-Einsatzspannung Ladespannung Gleichspannung Spannung (Flyback) Eingangsspannung Ausgangssspannung Betriebsspannung Impuls-Spitzenspannung Spannungshub Nennspannung Amplitude der Nenn-Wechselspannung VSC Vsn (Sinusoidal) alternating voltage, root-mean-square value S-correction voltage Snubber capacitor voltage Z Impedance Spannung bei Anwendung "S-correction" Spannung bei Anwendung "Beschaltung" Scheinwiderstand Lead spacing Rasterma Please read Cautions and warnings and Important notes at the end of this document. (Sinusformige) Wechselspannung Page 18 of 19 Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or lifesaving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. The aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products. 6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the "General Terms of Delivery for Products and Services in the Electrical Industry" published by the German Electrical and Electronics Industry Association (ZVEI). 7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSMP, CSSP, CTVS, DSSP, MiniBlue, MKK, MLSC, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks. Page 19 of 19