SNAP Isolated Analog Input Modules Features Description SNAP I/O isolated analog input modules provide two or more channels isolated from each other, thereby eliminating problems caused by ground loop currents. These isolated analog modules are part of Opto 22's SNAP PAC System and mount on SNAP PAC racks with an I/O processor (brain or onthe-rack controller). SNAP isolated analog input modules are compatible with all SNAP PAC brains and rack-mounted controllers, including Wired+WirelessTM. Since many SNAP analog input modules are softwareconfigurable and handle a wide variety of signal levels, a small number of modules can support a wide range of input requirements. Modules provide high resolution for precise signal levels, and all SNAP analog modules are factory calibrated. Part numbers ending in -FM are Factory Mutual approved. Dimensional drawings start on page 14. SNAP analog input modules have an on-board microprocessor to provide module-level intelligence, making them an ideal choice for original equipment manufacturers (OEMs). For more information about standalone SNAP analog modules, see the SNAP I/O Module Integration Guide (form 876). SNAP racks use a retention rail locking system that holds modules in place. In addition, Opto 22 recommends using two 4-40 by 1/2-inch standard machine screws to secure each module to the rack (recommended torque: 4 inch pounds [0.45 Newton meters]). Channel-to-channel isolation gives you complete freedom from ground-loop problems even on grounded devices connected to channels on the same module. Transformer isolation prevents ground loop currents from flowing between field devices and causing noise that produces erroneous readings. Ground loop currents are caused when two grounded field devices share a connection, and the ground potential at each device is different. Isolation also provides protection for sensitive control electronics from industrial field signals. Part Numbers Part Pg Isolated two-channel 0 to 10 amp RMS AC/DC input 2 SNAP-AIVRMS-i SNAP-AIVRMS-i-FM* Isolated two-channel 0 to 250 V RMS AC/DC input 3 SNAP-AIMA-i Isolated two-channel analog current input -20 mA to +20 mA 4 SNAP-AIMA-iSRC SNAP-AIMA-iSRC-FM* Isolated two-channel analog current input -20 mA to +20 mA, with loop sourcing 5 SNAP-AIMA2-i Isolated two-channel analog current input -1 mA to +1 mA 6 SNAP-AIRATE-HFi Isolated two-channel analog frequency input, 2 Hz to 500 kHz or 20 Hz to 500 kHz 7 SNAP-AITM-i Isolated two-channel analog type E, J, or K thermocouple or 150 mV or 75 mV input 9 SNAP-AITM2-i Isolated two-channel analog type B, C, D, G, N, T, R, or S thermocou- 10 ple or 50 mV or 25 mV input SNAP-AITM-4i Isolated four-channel analog type B, C, D, E, G, J, K, N, R, S, or T thermocouple or 150 mV, 75 mV, 50 mV, or 25 mV input 11 SNAP-AIV-i Isolated two-channel analog voltage input 10 VDC or 5 VDC 12 SNAP-AIV2-i Isolated two-channel analog voltage input 100 VDC or 50 VDC 13 DATA SHEET SNAP-AIARMS-i SNAP-AIARMS-i-FM* Isolation All SNAP analog input modules are isolated from all other modules and from the I/O processor. In addition, the modules in this data sheet have all channels isolated from each other. Description Form 1182-150113 Notes for legacy hardware: Most isolated analog input modules can be used with SNAP Simple, SNAP Ethernet, SNAP Ultimate, and SNAP mistic brains such as the serial B3000, and with M-series or B-series mounting racks. For exceptions, see individual module descriptions. SNAP Isolated Analog Input Modules SNAP Isolated Analog Input Modules Channel-to-channel isolation Rugged packaging and convenient pluggable wiring. Accepts 22 to 14 AWG wire. Factory calibrated; no user adjustment necessary Out-of-range indication Operating temperature -20 C to 70 C * Factory Mutual approved Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2006-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. PAGE 1 SNAP Isolated Analog Input Modules Isolated 0 to 10 Amp RMS AC/DC Input Module Part Number Description SNAP-AIARMS-i SNAP-AIARMS-i-FM Isolated two-channel 0 to 10 amp RMS AC/DC input Description DATA SHEET Form 1182-150113 SNAP Isolated Analog Input Modules The SNAP-AIARMS-i and SNAP-AIARMS-i-FM modules provide an input range of 0 to 10 amps RMS AC/DC. An ideal input is the 5-amp secondary of a standard current transformer used to monitor AC line current. These modules may also be used to monitor AC current to greater than a 100-amp range, using a current transformer of suitable ratio. The SNAP-AIARMS-i-FM module is Factory Mutual approved. PAGE 2 The two channels are isolated from each other; they do not share any field connection. These modules are ideal for differential current measurements. Specifications IMPORTANT: The mounting rack connector has 24 pins; the module connector has 20 pins. The extra pins on the mounting rack connector prevent misalignment of the module during installation. Input Range 0 to 10 amp RMS AC/DC Input Over Range To 11 amps Input Resistance 0.005 ohms Maximum Input 11 amps AC/DC Accuracy (AC) 8 mA and 0.2% reading Resolution 400 A DC Reversal 16 mA (0.16%) Input Response Time (Step Change) 63.2% (6.32 A) in 50 ms 99% (9.92 A) in 75 ms Data Freshness (Max) 0.025 ms DC Common Mode Rejection >-120 dB AC Common Mode Rejection >-120 dB at 60 Hz Maximum Operating Voltage Between Channels Common Mode Voltage 250 V 250 V Isolation: Optical 4000 V Isolation: Transformer 1500 V Isolation: Channel to Channel 250 V continuous (1500 V transient) Power Requirements 5 VDC (0.15 V) at 200 mA Ambient Temperature: Operating Storage -20 C to 70 C -40 C to 85 C Torque, hold-down screws 4 in-lb (0.45 N-m) Torque, connector screws 5.26 in-lb (0.6 N-m) Wire size range 22 to 14 AWG Agency Approvals CE, RoHS, DFARS FM (SNAP-AIARMS-FM only) Warranty Lifetime Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2006-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. SNAP Isolated Analog Input Modules Isolated 0 to 250 Volt RMS AC/DC Input Module Part Number Description SNAP-AIVRMS-i SNAP-AIVRMS-i-FM Isolated two-channel 0 to 250 V RMS AC/DC input Description The two channels are isolated from each other; they do not share any field connection. These modules are ideal for differential voltage measurements. Specifications 0 to 250 V RMS AC/DC Input Over Range To 275 V Input Resistance 1 megohms Accuracy 0.2 V and 0.2% reading Resolution 10 mV DC Reversal 0.2 V (0.08%) Input Response Time (Step Change) 63.2% (158 V) in 50 ms 99% (248 V) in 75 ms 25 ms DC Common Mode Rejection >-120 dB AC Common Mode Rejection >-120 dB @ 60 Hz Maximum Operating Voltage Between Channels Common Mode Voltage 250 V 250 V Isolation: Optical 4000 V Isolation: Transformer 1500 V Isolation: Channel to Channel 250 V continuous (1500 V transient) Power Requirements 5 VDC (0.15 V) at 200 mA Ambient Temperature: Operating Storage -20 C to 70 C -40 C to 85 C Torque, hold-down screws 4 in-lb (0.45 N-m) Torque, connector screws 5.26 in-lb (0.6 N-m) Wire size range 22 to 14 AWG Agency Approvals CE, RoHS, DFARS Warranty Lifetime Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2006-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. Form 1182-150113 Data Freshness DATA SHEET IMPORTANT: The mounting rack connector has 24 pins; the module connector has 20 pins. The extra pins on the mounting rack connector prevent misalignment of the module during installation. Input Range SNAP Isolated Analog Input Modules The SNAP-AIVRMS-i and SNAP-AIVRMS-i -FM modules provide an input range of 0 to 250 volts AC or DC. These modules may be used to monitor 120/240-volt AC/DC and 12/24/48-volt AC/DC system voltage. The SNAP-AIVRMS-i-FM module is Factory Mutual approved. PAGE 3 SNAP Isolated Analog Input Modules Isolated Current Input Module -20 mA to +20 mA Part Number Description SNAP-AIMA-i Isolated two-channel analog current input -20 mA to +20 mA SNAP Isolated Analog Input Modules Specifications Input Range -20 mA to +20 mA Maximum Over Range 10% (= 27500 counts) Resolution 0.8 A Input Response Time (% of span/delta I/delta time) 99.9 %/19.9 A/10 mS Data Freshness 11 ms DC Common Mode Rejection >-120 dB AC Common Mode Rejection >-120 dB @ 60 Hz Maximum Survivable Input 36 mA or 9 VDC Maximum Operating Common Mode Voltage 250 V Accuracy 0.05% (10 A) Isolation: Optical 4000 V Isolation: Transformer 1500 V Isolation: Channel to Channel 250 V continuous (1500 V transient) DRIFT: Gain Temperature Coefficient 30 PPM/ C DRIFT: Offset Temperature Coefficient 15 PPM/ C Power Requirements 5 VDC (0.15 ) @ 200 mA Input Resistance - Single Ended 200 ohms (each channel) IMPORTANT: The mounting rack connector has 24 pins; the module connector has 20 pins. The extra pins on the mounting rack connector prevent misalignment of the module during installation. Ambient Temperature: Operating Storage -20 C to 70 C -40 C to 85 C Torque, hold-down screws 4 in-lb (0.45 N-m) Torque, connector screws 5.26 in-lb (0.6 N-m) Wire size range 22 to 14 AWG Agency Approvals UL, CE, FM, RoHS, DFARS Warranty Lifetime DATA SHEET Form 1182-150113 Description PAGE 4 The SNAP-AIMA-i module provides an input range of -20mA to +20mA. The SNAP-AIMA-i has two channels that are isolated from each other. This module DOES NOT supply loop excitation current. See page 5 for a loop sourcing model. Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2006-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. SNAP Isolated Analog Input Modules Isolated Current Input Module -20mA to +20mA with Loop Sourcing Specifications Part Number Description SNAP-AIMA-iSRC SNAP-AIMA-iSRC-FM Isolated two-channel analog current input -20 mA to +20 mA, with loop sourcing 0 to +20 mA with loop sourcing -20 mA to +20 mA Description Maximum Over Range 10% (= 27500 counts) Resolution 0.8 A Input Response Time (% of span/delta I/delta time) 99.9 %/19.9 mA/10 ms Data Freshness 11 ms DC Common Mode Rejection >-120 dB AC Common Mode Rejection >-120 dB @ 60 Hz The SNAP-AIMA-iSRC and SNAP-AIMA-iSRC-FM are similar to the SNAP-AIMA-i module but include built-in loop sourcing capability. With the connection of a single 24 V power supply, these modules source 24 V for two 4-20 mA loops. The loops are internally connected to the individual inputs. The two channels and their loop sources are isolated from each other; they do not share any field connection. In addition, each loop source is current limited so that an external fault on one loop will not affect the other. Maximum Survivable Input 36 mA or 9 VDC Maximum Operating Common Mode Voltage 250 V Accuracy 0.05% (10 A) DRIFT: Gain Temperature Coefficient 30 PPM/ C DRIFT: Offset Temperature Coefficient 15 PPM/ C Isolation: Optical 4000 V Isolation: Transformer 1500 V Isolation: Channel to Channel 250 V continuous (1500 V transient) Power Requirements 5 VDC (0.15) @ 200 mA Power Requirements Loop Power (Input) From separate field connector: 24 VDC nominal (70 mA max @ 24 V input, both loops @ 20 mA), 30 VDC maximum Loop Power (Output) 24 VDC ( 1.5 V) @ 20 mA Open loop: 30 V maximum Shorted loop: 24 mA nominal LED on top of module Indicates that there is power to the 24v source supply 2-pin connector Input Resistance 200 ohms (each channel) Ambient Temperature: Operating Storage -20 C to 70 C -40 C to 85 C Torque, hold-down screws 4 in-lb (0.45 N-m) The SNAP-AIMA-iSRC-FM is Factory Mutual approved. 22 to 14 AWG Agency Approvals CE, RoHS, DFARS FM (SNAP-AIMA-iSRC-FM only) Warranty Lifetime IMPORTANT: The mounting rack connector has 24 pins; the module connector has 20 pins. The extra pins on the mounting rack connector prevent misalignment of the module during installation. Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2006-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. Form 1182-150113 5.26 in-lb (0.6 N-m) Wire size range DATA SHEET Torque, connector screws SNAP Isolated Analog Input Modules Input Range PAGE 5 SNAP Isolated Analog Input Modules Isolated Current Input Module -1 mA to +1 mA Part Number Description SNAP-AIMA2-i Isolated two-channel analog current input -1 mA to +1 mA Description SNAP Isolated Analog Input Modules The SNAP-AIMA2-i module provides an input range of -1 mA to +1 mA. The SNAP-AIMA2-i has two channels that are isolated from each other. This module DOES NOT supply loop excitation current. Specifications DATA SHEET Form 1182-150113 IMPORTANT: The mounting rack connector has 24 pins; the module connector has 20 pins. The extra pins on the mounting rack connector prevent misalignment of the module during installation. PAGE 6 Input Range -1 mA to +1mA Maximum Over Range 10% (= 27500 counts) Resolution 0.04 A Input Response Time (% of span/delta I/delta time) 99.9 %/19.9 A/10 ms Data Freshness 11 ms DC Common Mode Rejection >-120 dB AC Common Mode Rejection >-120 dB @ 60 Hz Maximum Survivable Input 11 mA or 28 VDC Maximum Operating Common Mode Voltage 250 V Accuracy 0.05% (0.05 A) DRIFT: Gain Temperature Coefficient 30 PPM/ C DRIFT: Offset Temperature Coefficient 15 PPM/ C Isolation: Optical 4000 V Isolation: Transformer 1500 V Isolation: Channel to Channel 250 V continuous (1500 V transient) Power Requirements 5 VDC (0.15 ) @ 200 mA Input Resistance 5 K ohms (each channel) Ambient Temperature: Operating Storage -20 C to 70 C -40 C to 85 C Torque, hold-down screws 4 in-lb (0.45 N-m) Torque, connector screws 5.26 in-lb (0.6 N-m) Wire size range 22 to 14 AWG Agency Approvals CE, RoHS, DFARS Warranty Lifetime Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2006-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. SNAP Isolated Analog Input Modules Isolated Frequency Input Module Part Number Description SNAP-AIRATE-HFi Isolated two-channel analog frequency input, 2 Hz-500 kHz or 20 Hz-500 kHz Specifications Description Nine volts through a 3.6 kOhm pull-up resistor is provided internally for each channel for use with devices that have open-collector outputs. This feature eliminates the need for you to provide the pull-up voltage supply and associated wiring, barrier strips, and so on. The module works with TTL, CMOS, and open-collector outputs. The two channels on the module are isolated from each other. Since these channels do not share any common connections, grounded sensors and field devices may be used with them. This module requires a SNAP PAC controller or brain with SNAP PAC firmware version 9.3c or higher. It cannot be used with legacy controllers or brains. Input Range 2 Hz - 500 kHz at 1.0 s Data Freshness 20 Hz - 500 kHz at 0.1 s Data Freshness Input Voltage Range Sine wave >= 2000 Hz Sine wave at 200 Hz Sine wave at 20 Hz Sine wave at 2 Hz Square wave Maximum survivable 3.0 V to 48 Vp-p 4.0 V to 48 Vp-p 5.0 V to 48 Vp-p 17 V to 48 Vp-p 3.0 V to 48 Vp-p 110 Vp-p Input Impedance 55 kOhms Input Coupling Single-ended AC Pull-up Voltage 6 to 9 VDC Pull-up Resistor 3.6 kOhm Minimum Pulse Width 1 microsecond Data Freshness* 100 ms at 20 Hz - 500 kHz 1.0 s at 2 Hz to 500 kHz Resolution (Hz) f / (48,000,000 * Data Freshness), where f is the current frequency measurement Accuracy +- 0.005% of input for input greater than 500 Hz. +- 0.005% of input plus an additional +- 0.1 Hz for input less than 500 Hz. Maximum Operating Common Mode Voltage 250 V Continuous 1500 V Transient DC Common Mode Rejection > -120 dB See wiring diagrams on the following page. AC Common Mode Rejection > -120 dB at 60 Hz Isolation: Channel to Channel 250 V Continuous 1500 V Transient Power Consumption 1.05 W (210 mA @ 5 V) Ambient Temperature Operating Storage -20 to 70 C -40 to 85 C Torque, hold-down screws 4 in-lb (0.45 N-m) Torque, connector screws 5.26 in-lb (0.6 N-m) Wire size range 22 to 14 AWG Agency Approvals CE, RoHS, DFARS Warranty Lifetime (c) 2006-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. Form 1182-150113 Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com DATA SHEET * User selectable. Default is 0.1 seconds. SNAP Isolated Analog Input Modules The SNAP-AIRATE-HFi module provides frequency to digital conversion. Each channel can be configured for a 0.1-second measurement interval, providing an input range of 20 Hz to 500 kHz, or a 1-second measurement interval, providing an input range of 2 Hz to 500 kHz. Data freshness is dependent upon and directly related to the measurement interval. PAGE 7 SNAP Isolated Analog Input Modules Isolated Frequency Input Module (cont'd) DATA SHEET The two channels on the module are isolated from each other. Since these channels do not share any common connections, grounded sensors and field devices may be used with them. Form 1182-150113 SNAP Isolated Analog Input Modules SNAP-AIRATE-HFi Wiring Diagrams PAGE 8 Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2006-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. SNAP Isolated Analog Input Modules Isolated Thermocouple/ Millivolt Input Module Part Number Description SNAP-AITM-i Isolated two-channel analog type E, J, or K thermocouple or -150 mV to +150 mV input or -75 mV to +75 mV input Specifications From -150 mV to +150 mV From -75 mV to +75 mV Maximum Over Range 10% (= 27500 counts) Resolution 6 V from -150 mV to +150 mV 3 V from -75 mV to +75 mV Cold Junction Temperature Compensation Automatic when used with SNAP brains Input Filtering -3 dB @ 7 Hz Input Response Time (% of span/delta V/delta time) 63.2%/95 mV/23 mS Data Freshness 65 ms for +/- 150 mV 130 ms for +/- 75 mV 130 ms for E-, J-, and K-type thermocouples DC Common Mode Rejection >-120 dB AC Common Mode Rejection >-120 dB @ 60 Hz Maximum Survivable Input 15 volts Maximum Operating Common Mode Voltage 250 V Accuracy 0.06% (90 V) @ 150 mV (full scale) 0.1% (75 V) @ 75 mV (full scale) Drift: Gain Temperature Coefficient 5 V / C Drift: Offset Temperature Coefficient 2 V / C Thermocouple Accuracy [C] From factory After user gain and offset commands 2.0 (E, J, and K) 0.8 Isolation: Optical 4000 V Isolation: Transformer 1500 V Isolation: Channel to Channel 250 V continuous (1500 V transient) Power Requirements 5 VDC (0.15) @ 200 mA Input Resistance 100 megohms (each channel) Ambient Temperature: Operating Storage -20 C to 70 C -40 C to 85 C 3 in-lb (0.34 N-m) Wire size range 22 to 14 AWG Agency Approvals CE, FM, RoHS, DFARS Warranty Lifetime Type - + Range Purple -270 C to +1,000 C E Red J Red White -210 C to +1,200 C K Red Yellow -270 C to +1,372 C IMPORTANT: The mounting rack connector has 24 pins; the module connector has 20 pins. The extra pins on the mounting rack connector prevent misalignment of the module during installation. Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2006-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. Form 1182-150113 4 in-lb (0.45 N-m) Torque, connector screws The SNAP-AITM-i module provides two channels of analog to digital conversion. Each channel on the module can be configured for -150 mV DC to +150 mV DC or -75 mV DC to +75 mV DC, or for type E, J, or K thermocouple operation. The two channels are isolated from each other. Since these channels do not share any common connections, grounded sensors and field devices may be used with them. DATA SHEET Torque, hold-down screws Description SNAP Isolated Analog Input Modules Input Range PAGE 9 SNAP Isolated Analog Input Modules SNAP Isolated Analog Input Modules Isolated Thermocouple/ Millivolt Input Module Type - + Range B RED GRAY +42 C to +1,820 C C, D, G RED WHITE 0 C to +2,320 C N RED ORANGE -270 C to +1,300 C R, S RED BLACK -50 C to +1,768 C T RED BLUE -270 C to +400 C IMPORTANT: The mounting rack connector has 24 pins; the module connector has 20 pins. The extra pins on the mounting rack connector prevent misalignment of the module during installation. DATA SHEET Form 1182-150113 Description PAGE 10 The SNAP-AITM2-i module provides an input range of 50 mV, 25 mV, or Type B, C, D, G, N, T, R, or S thermocouple. The two channels on the module are isolated from each other. Since these channels do not share any common connections, grounded sensors and field devices may be used with them. Part Number Description SNAP-AITM2-i Isolated two-channel analog type B, C, D, G, N, T, R, or S thermocouple or -50 mV to +50 mVDC input or 25 mV to +25 mVDC input Specifications Input Range From -50 mV to +50 mVDC From -25 mV to +25 mVDC Maximum Over Range 10% (= 27500 counts) Resolution 2 V from -50 mV to +50 mV 1 V from -25 mV to +25 mV Cold Junction Temperature Compensation Automatic when used with SNAP brains Input Filtering -3 dB @ 2.4 Hz Input Response Time (% of span/delta V/delta time) 63.2%/31.5 mV/66 ms Data Freshness 65 ms for +/- 50 mV 130 ms for +/- 25 mV 130 ms for B-, R-, S-, and T-type thermocouples 65 ms for C-, D-, G-, and N-type thermocouples DC Common Mode Rejection >-120 dB AC Common Mode Rejection >-120 dB @ 60 Hz Maximum Survivable Input 15 volts Maximum Operating Common Mode Voltage 250 V Accuracy 0.1% (50 V) @ 50 mV (full scale) 0.2% (50 V) @ 25 mV (full scale) Drift: Gain Temperature Coefficient 5 V / C Drift: Offset Temperature Coefficient 2 V / C Thermocouple Accuracy [C] From factory After user gain and offset commands B, R, S 5 3 C, D, G 4 2 T, N 3 2 Isolation: Optical 4000 V Isolation: Transformer 1500 V Isolation: Channel to Channel 250 V continuous (1500 V transient) Power Requirements 5 VDC (0.15 ) @ 200 mA Input Resistance 100 megohms (each channel) Ambient Temperature: Operating Storage -20 C to 70 C -40 C to 85 C Torque, hold-down screws 4 in-lb (0.45 N-m) Torque, connector screws 3 in-lb (0.34 N-m) Wire size range 22 to 14 AWG Agency Approvals CE, FM, RoHS, DFARS Warranty Lifetime Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2006-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. SNAP Isolated Analog Input Modules Isolated Thermocouple/ Millivolt Input Module Part Number Description SNAP-AITM-4i Isolated four-channel analog type B, C, D, E, G, J, K, N, R, S, or T thermocouple or 150 mV, 75 mV, 50 mV, or 25 mV input Specifications Description Maximum Over Range 10% (= 27500 counts) Resolution 6 V from -150 mV to +150 mV 3 V from -75 mV to +75 mV 2 V from -50 mV to +50 mV 1 V from -25 mV to +25 mV Cold Junction Temperature Compensation Automatic when used with SNAP PAC brains Input Filtering -3 dB @ 5 Hz Data Freshness mV input: 75 ms Thermocouple input: 140 ms The SNAP-AITM-4i module provides an input range of 150 mV, 75 mV, 50 mV, 25 mV, or Type B, C, D, E, G, J, K, N, R, S, or T thermocouple. The four channels on the module are isolated from each other. Since these channels do not share any common connections, grounded sensors and field devices may be used with them. SNAP-AITM-4i requires a SNAP PAC rack, a SNAP PAC brain or R-series controller with firmware 9.1 or newer, and PAC Project 9.1 or newer. DC Common Mode Rejection >-120 dB AC Common Mode Rejection >-120 dB @ 60 Hz Maximum Survivable Input 15 volts C, D, G Maximum Operating Common Mode Voltage 250 V E 0.06% (90 V) @ 150 mV (full scale) 0.1% (75 V) @ 75 mV (full scale) 0.1% (50 V) @ 50 mV (full scale) 0.2% (50 V) @ 25 mV (full scale) J Accuracy Drift: Gain Temperature Coefficient 5 V / C Drift: Offset Temperature Coefficient 2 V / C Thermocouple Accuracy [C] B,R,S C,D,G E,J,K N,T 4.0 2.0 3.0 3.0 2.0 0.8 2.0 Isolation: Transformer 1500 V Isolation: Channel to Channel 250 V continuous (1500 V transient) Power Requirements 5 VDC (0.15 ) @ 150 mA Input Resistance 100 megohms (each channel) Ambient Temperature: Operating Storage -20 C to 70 C -40 C to 85 C Torque, connector screws 3 in-lb (0.34 N-m) Wire size range 22 to 14 AWG Agency Approvals CE, RoHS, DFARS Warranty Lifetime + Range B Red Gray +42 C to +1,820 C Red White 0 C to +2,320 C Red Purple -270 C to +1,000 C Red White -210 C to +1,200 C K Red Yellow -270 C to +1,372 C N Red Orange -270 C to +1,300 C R, S Red Black -50 C to +1,768 C T Red Blue -270 C to +400 C CH0 + - CH1 + - CH2 + - CH3 + - Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2006-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. Form 1182-150113 5.0 - DATA SHEET From factory After user gain and offset commands Type SNAP Isolated Analog Input Modules Input Range From -150 mV to +150 mVDC From -75 mV to +75 mVDC From -50 mV to +50 mVDC From -25 mV to +25 mVDC PAGE 11 SNAP Isolated Analog Input Modules Isolated Voltage Input Module -10 VDC to +10 VDC or -5 VDC to +5 VDC Part Number Description SNAP-AIV-i Isolated two-channel analog voltage input -10 VDC to +10 VDC or -5 VDC to +5 VDC SNAP Isolated Analog Input Modules Specifications IMPORTANT: The mounting rack connector has 24 pins; the module connector has 20 pins. The extra pins on the mounting rack connector prevent misalignment of the module during installation. Description DATA SHEET Form 1182-150113 The SNAP-AIV-i module can be configured for either -10 VDC to +10 VDC or -5 VDC to +5 VDC operation on each channel. The SNAP-AIV-i provides two channels that are isolated from each other. Since these channels do not share any common connections, grounded sensors and field devices may be used with them. PAGE 12 Input Range From -10 volts to +10 volts From -5 volts to +5 volts Maximum Over Range 10% (= 27500 counts) Resolution 0.4 mV when configured -10 volts to +10 volts 0.2 mV when configured -5 volts to +5 volts Input Filtering -3 dB @ 64 Hz Input Response Time (% of span/ DV / Dt) 63.2% / 6.7 V / 10 mS Data Freshness 11 ms for +/- 10 V 18 ms for +/- 5 V DC Common Mode Rejection >-120 dB AC Common Mode Rejection >-120 dB @ 60 Hz Maximum Survivable Input 220 VAC or 300 VDC Maximum Operating Common Mode Voltage 250 V Accuracy 0.05%, 5 mV @ 10 VDC 2.5 mV @ 5 VDC Gain Temperature Coefficient 30 PPM/ C Offset Temperature Coefficient 15 PPM/ C Isolation: Optical 4000 V Isolation: Transformer 1500 V Isolation: Channel to Channel 250 V continuous (1500 V transient) Power Requirements 5 VDC (0.15) @ 200 mA Input Resistance 1 megohms (each channel) Ambient Temperature: Operating Storage -20 C to 70 C -40 C to 85 C Torque, hold-down screws 4 in-lb (0.45 N-m) Torque, connector screws 5.26 in-lb (0.6 N-m) Wire size range 22 to 14 AWG Agency Approvals CE, FM, RoHS, DFARS Warranty Lifetime Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2006-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. SNAP Isolated Analog Input Modules Isolated Voltage Input Module -100 VDC to +100 VDC or -50 VDC to +50 VDC Part Number Description SNAP-AIV2-i Isolated two-channel analog voltage input -100 VDC to +100 VDC or -50 VDC to +50 VDC Specifications From -100 volts to +100 volts From -50 volts to +50 volts Maximum Over Range 10% (= 27500 counts) Resolution 4.0 mV when configured -100 volts to +100 volts 2.0 mV when configured -50 volts to +50 volts Input Filtering -3 dB @ 64 Hz Input Response Time (% of span/ DV / Dt) 63.2% / 6.7 V / 10 mS Data Freshness 11 ms for +/- 100 V 18 ms for +/- 50 V DC Common Mode Rejection >-120 dB AC Common Mode Rejection >-120 dB @ 60 Hz Maximum Survivable Input 220 VAC or 300 VDC Maximum Operating Common Mode Voltage 250 V Accuracy 0.05%, 50 mV @ 100 VDC 25 mV @ 50 VDC Gain Temperature Coeffi30 PPM/ C cient IMPORTANT: The mounting rack connector has 24 pins; the module connector has 20 pins. The extra pins on the mounting rack connector prevent misalignment of the module during installation. Description The SNAP-AIV2-i module can be configured for either -100 VDC to +100 VDC or -50 VDC to +50 VDC operation on each channel. The SNAP-AIV2-i provides two channels that are isolated from each other. Since these channels do not share any common connections, grounded sensors and field devices may be used with them. Offset Temperature Coef15 PPM/ C ficient Isolation: Optical 4000 V Isolation: Transformer 1500 V Isolation: Channel to Channel 250 V continuous (1500 V transient) Power Requirements 5 VDC (0.15) @ 200 mA Input Resistance 1 megohms (each channel) Ambient Temperature: Operating Storage -20 C to 70 C -40 C to 85 C Torque, hold-down screws SNAP Isolated Analog Input Modules Input Range 4 in-lb (0.45 N-m) Torque, connector screws 5.26 in-lb (0.6 N-m) CE, RoHS, DFARS Warranty Lifetime Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2006-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. Form 1182-150113 22 to 14 AWG Agency Approvals DATA SHEET Wire size range PAGE 13 SNAP Isolated Analog Input Modules Dimensional Drawing DATA SHEET Form 1182-150113 SNAP Isolated Analog Input Modules All Modules Except SNAP-AITM-i, SNAP-AITM2-i, SNAP-AITM-4i, SNAP-AIMA-iSRC, and SNAP-AIMA-iSRC-FM PAGE 14 Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2006-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. SNAP Isolated Analog Input Modules Dimensional Drawing SNAP-AITM-i and SNAP-AITM2-i Modules SNAP Isolated Analog Input Modules Form 1182-150113 (c) 2006-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. DATA SHEET Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com PAGE 15 SNAP Isolated Analog Input Modules Dimensional Drawing DATA SHEET Form 1182-150113 SNAP Isolated Analog Input Modules SNAP-AITM-4i Module PAGE 16 Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2006-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. SNAP Isolated Analog Input Modules Dimensional Drawing SNAP-AIMA-iSRC and SNAP-AIMA-iSRC-FM Modules SNAP Isolated Analog Input Modules Form 1182-150113 (c) 2006-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. DATA SHEET Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com PAGE 17 SNAP Isolated Analog Input Modules Dimensional Drawing SNAP Isolated Analog Input Modules All Modules DATA SHEET Form 1182-150113 IMPORTANT: The mounting rack connector has 24 pins; the module connector has 20 pins. The extra pins on the mounting rack connector prevent misalignment of the module during installation. PAGE 18 Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2006-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. SNAP Isolated Analog Input Modules Dimensional Drawing SNAP Isolated Analog Input Modules Form 1182-150113 (c) 2006-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. DATA SHEET Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com PAGE 19 SNAP Isolated Analog Input Modules Dimensional Drawing DATA SHEET Form 1182-150113 SNAP Isolated Analog Input Modules Height on Rack: SNAP-AITMi and SNAP-AITM2-i Modules PAGE 20 Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2006-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. More About Opto 22 Products Opto 22 develops and manufactures reliable, flexible, easy-to-use hardware and software products for industrial automation, energy management, remote monitoring, and data acquisition applications. groov groov puts your system on your mobile device. With zero programming, you can build mobile operator interfaces to monitor and control systems from Allen-Bradley, Siemens, Schneider Electric, Modicon, and many more. Web-based groov puts mobile-ready gadgets at your fingertips. Tag them from your existing tag database, and they automatically scale for use on any device with a modern web browser. See groov.com for more information and your free trial. SNAP PAC System Designed to simplify the typically complex process of selecting and applying an automation system, the SNAP PAC System consists of four integrated components: * SNAP PAC controllers * PAC ProjectTM Software Suite * SNAP PAC brains * SNAP I/OTM SNAP PAC Controllers Programmable automation controllers (PACs) are multifunctional, modular controllers based on open standards. Opto 22 has been manufacturing PACs for over two decades. The standalone SNAP PAC S-series, the rack-mounted SNAP PAC Rseries, and the software-based SoftPACTM all handle a wide range of digital, analog, and serial functions for data collection, remote monitoring, process control, and discrete and hybrid manufacturing. SNAP PACs are based on open Ethernet and Internet Protocol (IP) standards, so you can build or extend a system easily, without the expense and limitations of proprietary networks and protocols. Wired+WirelessTM models are also available. PAC Project Software Suite Opto 22's PAC Project Software Suite provides full-featured, costeffective control programming, HMI (human machine interface) development and runtime, OPC server, and database connectivity software for your SNAP PAC System. Control programming includes both easy-to-learn flowcharts and optional scripting. Commands are in plain English; variables and I/ O point names are fully descriptive. PAC Project Basic offers control and HMI tools and is free for download on our website, www.opto22.com. PAC Project Professional, available for separate purchase, adds one SoftPAC, OptoOPCServer, OptoDataLink, options for controller redundancy or segmented networking, and support for legacy Opto 22 serial misticTM I/O units. SNAP PAC Brains While SNAP PAC controllers provide central control and data distribution, SNAP PAC brains provide distributed intelligence for I/O processing and communications. Brains offer analog, digital, and serial functions, including thermocouple linearization; PID loop control; and optional high-speed digital counting (up to 20 kHz), quadrature counting, TPO, and pulse generation and measurement. SNAP I/O I/O provides the local connection to sensors and equipment. Opto 22 SNAP I/O offers 1 to 32 points of reliable I/O per module, depending on the type of module and your needs. Analog, digital, and serial modules are all mixed on the same mounting rack and controlled by the same processor (SNAP PAC brain or rack-mounted controller). Quality Founded in 1974, Opto 22 has established a worldwide reputation for high-quality products. All are made in the U.S.A. at our manufacturing facility in Temecula, California. Because we test each product twice before it leaves our factory, rather than only testing a sample of each batch, we can guarantee most solid-state relays and optically isolated I/O modules for life. Free Product Support Opto 22's California-based Product Support Group offers free, comprehensive technical support for Opto 22 products. Our staff of support engineers represents decades of training and experience. Support is available in English and Spanish by phone or email, Monday-Friday, 7 a.m. to 5 p.m. PST. Additional support is always available on our website: how-to videos, OptoKnowledgeBase, self-training guide, troubleshooting and user's guides, and OptoForums. In addition, hands-on training is available for free at our Temecula, California headquarters, and you can register online. Purchasing Opto 22 Products Opto 22 products are sold directly and through a worldwide network of distributors, partners, and system integrators. For more information, contact Opto 22 headquarters at 800-3216786 or 951-695-3000, or visit our website at www.opto22.com. www.opto22.com www.opto22.com * Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * Form 1335-131203 SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2014 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.