Supercapacitors FM Series Overview Applications FM Series Supercapacitors, also known as Electric DoubleLayer Capacitors (EDLCs), are intended for high energy storage applications. Supercapacitors have characteristics ranging from traditional capacitors and batteries. As a result, supercapacitors can be used like a secondary battery when applied in a DC circuit. These devices are best suited for use in low voltage DC hold-up applications such as embedded microprocessor systems with flash memory. Benefits * Rectangular case * Wide range of temperature from -25C to +70C (all types except FMR) and -40C to +85C (FMR type) * Maintenance free * 3.5 VDC, 5.5 VDC, and 6.5 VDC * Highly reliable against liquid leakage * Lead-free and RoHS Compliant * Leads can be transverse mounted Part Number System FM Series FM FME FML FMR FMC 0H 223 Z F TP 16 Maximum Capacitance Code (F) Operating Voltage Capacitance Tolerance Environmental Tape Type Height (excluding lead) 0V = 3.5 VDC 0H = 5.5 VDC 0J = 6.5 VDC Z = -20/+80% F = Lead-free TP = AMMO L1 = Transverse mounting Blank = Bulk First two digits represent significant figures. Third digit specifies number of zeros. 16 = 16 mm 18 = 18 mm Blank = Bulk One world. One KEMET (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com S6012_FM * 3/29/2017 1 Supercapacitors - FM Series Dimensions - Millimeters B 0.5 T 0.5 A 0.5 0.4 0.1 5 1 D1 0.1 D2 0.1 5 0.5 Part Number A B T D1 D2 FM0H103ZF FM0H223ZF FM0H473ZF FM0H104ZF FM0H224ZF FM0V473ZF FM0V104ZF FM0V224ZF FM0J473ZF FME0H223ZF FME0H473ZF FML0H333ZF FMR0H473ZF FMR0H104ZF FMR0V104ZF FMC0H473ZF FMC0H104ZF FMC0H334ZF 11.5 11.5 11.5 11.5 11.5 11.5 11.5 11.5 11.5 11.5 11.5 11.5 11.5 11.5 11.5 11.5 11.5 15.0 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 14.0 5.0 5.0 5.0 6.5 6.5 5.0 5.0 6.5 6.5 5.0 5.0 5.0 6.5 6.5 6.5 5.0 6.5 9.0 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.6 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.6 For transverse mounting <L1> Lead Terminal Forming Add "L1" to the end of bulk part number for transverse mounting option (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com S6012_FM * 3/29/2017 2 Supercapacitors - FM Series Performance Characteristics Supercapacitors should not be used for applications such as ripple absorption because of their high internal resistance (several hundred m to a hundred ) compared to aluminum electrolytic capacitors. Thus, its main use would be similar to that of secondary battery such as power back-up in DC circuit. The following list shows the characteristics of supercapacitors as compared to aluminum electrolytic capacitors for power back-up and secondary batteries. Secondary Battery Capacitor NiCd Lithium Ion Aluminum Electrolytic Supercapacitor Back-up ability - - - - Eco-hazard Cd - - - -20 to +60C -20 to +50C -55 to +105C -40 to +85C (FR, FT) few hours few hours few seconds few seconds approximately 500 times approximately 500 to 1,000 times limitless (*1) limitless (*1) yes yes none none Flow Soldering not applicable not applicable applicable applicable Automatic Mounting not applicable not applicable applicable applicable (FM and FC series) leakage, explosion leakage, combustion, explosion, ignition heat-up, explosion gas emission (*2) Operating Temperature Range Charge Time Charge/Discharge Life Time Restrictions on Charge/Discharge Safety Risks (*1) Aluminum electrolytic capacitors and supercapacitors have limited lifetime. However, when used under proper conditions, both can operate within a predetermined lifetime. (*2) There is no harm as it is a mere leak of water vapor which transitioned from water contained in the electrolyte (diluted sulfuric acid). However, application of abnormal voltage surge exceeding maximum operating voltage may result in leakage and explosion. Typical Applications Intended Use (Guideline) Power Supply (Guideline) Application Examples of Equipment Series Long time back-up 500 A and below CMOS microcomputer, IC for clocks CMOS microcomputer, static RAM/DTS (digital tuning system) FM series Environmental Compliance All KEMET supercapacitors are RoHS Compliant. RoHS Compliant (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com S6012_FM * 3/29/2017 3 Supercapacitors - FM Series Table 1 - Ratings & Part Number Reference Part Number Maximum Operating Voltage (VDC) Nominal Capacitance Maximum Voltage Holding Maximum ESR Current at 30 Characteristic Weight (g) Charge Discharge at 1 kHz () Minutes (mA) Minimum (V) System (F) System (F) FM0V473ZF 3.5 0.047 0.06 200 0.042 -- FMR0V104ZF 3.5 0.10 -- 50 0.090 -- 1.3 1.6 FM0V104ZF 3.5 0.10 0.13 100 0.090 -- 1.3 FM0V224ZF 3.5 0.22 0.30 100 0.20 -- 1.6 FM0H103ZF 5.5 0.01 0.014 300 0.015 4.2 1.3 FME0H223ZF 5.5 0.022 0.028 40 0.033 -- 1.3 FM0H223ZF 5.5 0.022 0.028 200 0.033 4.2 1.3 FML0H333ZF 5.5 -- 0.033 6.5 0.050 -- 1.3 FME0H473ZF 5.5 0.047 0.06 20 0.071 -- 1.3 FMC0H473ZF 5.5 0.047 0.06 100 0.071 4.2 1.3 FM0H473ZF 5.5 0.047 0.06 200 0.071 4.2 1.3 FMR0H473ZF 5.5 0.047 0.062 200 0.071 4.2 1.6 FMR0H104ZF 5.5 0.10 -- 50 0.15 4.2 1.6 FMC0H104ZF 5.5 0.10 0.13 50 0.15 4.2 1.6 FM0H104ZF 5.5 0.10 0.13 100 0.15 4.2 1.6 FM0H224ZF 5.5 -- 0.22 100 0.33 4.2 1.6 FMC0H334ZF 5.5 -- 0.33 25 0.50 4.2 3.5 FM0J473ZF 6.5 0.047 0.062 200 0.071 -- 1.6 (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com S6012_FM * 3/29/2017 4 Supercapacitors - FM Series Specifications - All Types Except FMR Item FM 5.5 V Type, 3.5 V Type, 6.5 V Type, FMC Type FML Type, FME Type Category Temperature Range -25C to +70C -25C to +70C Maximum Operating Voltage 5.5 VDC, 3.5 VDC, 6.5 VDC 5.5 VDC Test Conditions (conforming to JIS C 5160-1) Capacitance Refer to Table 1 Refer to Table 1 Refer to "Measurement Conditions" Capacitance Allowance +80%, -20% +80%, -20% Refer to "Measurement Conditions" ESR Refer to Table 1 Refer to Table 1 Measured at 1 kHz, 10 mA; See also "Measurement Conditions" Current (30 minutes value) Refer to Table 1 Refer to Table 1 Refer to "Measurement Conditions" Surge voltage: Capacitance > 90% of initial ratings > 90% of initial ratings ESR 120% of initial ratings 120% of initial ratings Current (30 minutes value) 120% of initial ratings 120% of initial ratings Charge: Discharge: Number of cycles: Series resistance: Surge Appearance Capacitance ESR Capacitance ESR Characteristics in Different Temperature No obvious abnormality Phase 2 Phase 3 Capacitance ESR Current (30 minutes value) Phase 5 Capacitance ESR Current (30 minutes value) 50% of initial value 400% of initial value Phase 6 No obvious abnormality Phase 2 50% of initial value 400% or less than initial value Phase 3 200% of initial value Satisfy initial ratings Phase 5 1.5 CV (mA) Within 20% of initial value Satisfy initial ratings Satisfy initial ratings Within 20% of initial value Satisfy initial ratings Satisfy initial ratings Capacitance Vibration Resistance ESR Current (30 minutes value) Appearance Solderability 0 702C Conforms to 4.17 Phase 1: Phase 2: Phase 4: Phase 5: Phase 6: +252C -252C +252C +702C +252C Conforms to 4.13 Frequency: Testing Time: 10 to 55 Hz 6 hours Conforms to 4.11 Solder temp: Dipping time: +2455C 50.5 seconds 200% of initial value Satisfy initial ratings 1.5 CV (mA) Phase 6 Discharge resistance: Temperature: 4.0 V (3.5 V type) 6.3 V (5.5 V type) 7.4 V (6.5 V type) 30 seconds 9 minutes 30 seconds 1,000 0.010 F 1,500 560 0.022 F 0.033 F 510 0.047 F 300 0.068 F 240 0.10 F 150 0.22 F 56 0.33 F 51 Satisfy initial ratings Satisfy initial ratings No obvious abnormality No obvious abnormality Over 3/4 of the terminal should be covered by the new solder Over 3/4 of the terminal should be covered by the new solder 1.6 mm from the bottom should be dipped. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com S6012_FM * 3/29/2017 5 Supercapacitors - FM Series Specifications - All Types Except FMR cont'd Item FM 5.5 V Type, 3.5 V Type, 6.5 V Type, FMC Type FML Type, FME Type Capacitance Solder Heat Resistance ESR Current (30 minutes value) Appearance Satisfy initial ratings Satisfy initial ratings Conforms to 4.10 Solder temp: Dipping time: No obvious abnormality No obvious abnormality 1.6 mm from the bottom should be dipped. Satisfy initial ratings Conforms to 4.12 Temperature Condition: Capacitance Temperature Cycle High Temperature and High Humidity Resistance High Temperature Load ESR Current (30 minutes value) Test Conditions (conforming to JIS C 5160-1) Satisfy initial ratings Appearance No obvious abnormality No obvious abnormality Capacitance Within 20% of initial value Within 20% of initial value ESR 120% of initial ratings 120% of initial ratings Current (30 minutes value) 120% of initial ratings 120% of initial ratings Appearance No obvious abnormality No obvious abnormality Capacitance Within 30% of initial value Within 30% of initial value ESR < 200% of initial ratings < 200% of initial ratings Current (30 minutes value) < 200% of initial ratings < 200% of initial ratings Appearance No obvious abnormality No obvious abnormality Number of cycles: Conforms to 4.14 Temperature: Relative humidity: Testing time: Conforms to 4.15 Temperature: Voltage applied: Series protection resistance: Testing time: Charging condition Voltage applied: Self Discharge Characteristics (Voltage Holding Characteristics) 5.5 V type: between terminal leads > 4.2 V 3.5 V type: 6.5 V type: Voltage Not specified Not specified Series resistance: Charging time: -25C Room temperature +70C Room temperature 5 cycles +402C 90 to 95% RH 2408 hours +702C Maximum operating voltage 0 1,000 +48 (+48/-0) hours 5.0 VDC (Terminal at the case side must be negative) 0 24 hours Storage Let stand for 24 hours in condition described below with terminals opened. Ambient temperature: Relative humidity: (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com +26010C 101 seconds < 25C < 70% RH S6012_FM * 3/29/2017 6 Supercapacitors - FM Series Specifications - FMR Type Item FMR Type Test Conditions (conforming to JIS C 5160-1) Category Temperature Range -40C to +85C Maximum Operating Voltage 5.5 VDC, 3.5 VDC Capacitance Refer to Table 1 Refer to "Measurement Conditions" Capacitance Allowance +80%, -20% Refer to "Measurement Conditions" ESR Refer to Table 1 Measured at 1 kHz, 10 mA; See also "Measurement Conditions" Current (30 minutes value) Refer to Table 1 Refer to "Measurement Conditions" Capacitance More than 90% of initial ratings ESR Not to exceed 120% of initial ratings Current (30 minutes value) Not to exceed 120% of initial ratings Appearance No obvious abnormality Surge Capacitance ESR Capacitance ESR Characteristics in Different Temperature Phase 2 Phase 3 Phase 5 Current (30 minutes value) 700% or less than initial value Satisfy initial ratings ESR No terminal damage Conforms to 4.9 Satisfy initial ratings Conforms to 4.13 Frequency: Testing Time: 10 to 55 Hz 6 hours Conforms to 4.11 Solder temp: Dipping time: +2455C 50.5 seconds No obvious abnormality Over 3/4 of the terminal should be covered by the new solder Solderability +252C -25 2C -40 2C +25 2C +70 2C +25 2C Satisfy initial ratings Current (30 minutes value) Appearance Conforms to 4.17 Phase 1: Phase 2: Phase 3: Phase 4: Phase 5: Phase 6: 0 852C Satisfy initial ratings Capacitance Vibration Resistance Discharge resistance: Temperature: Within 20% of initial value Phase 6 Current (30 minutes value) Lead Strength (tensile) 30% or higher than initial value Charge: Discharge: Number of cycles: Series resistance: 4.0 V (3.5 V type) 6.3 V (5.5 V type) 30 seconds 9 minutes 30 seconds 1,000 0.047 F 300 0.10 F 150 1.5 CV (mA) or below Capacitance ESR 400% or less than initial value 200% or less than initial value Capacitance ESR 50% higher than initial value Surge voltage: 1.6 mm from the bottom should be dipped. Capacitance Solder Heat Resistance ESR Satisfy initial ratings Conforms to 4.10 Solder temp: Dipping time: No obvious abnormality 1.6 mm from the bottom should be dipped. Satisfy initial ratings Conforms to 4.12 Temperature Condition: Current (30 minutes value) Appearance Capacitance Temperature Cycle ESR Current (30 minutes value) Appearance No obvious abnormality (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com Number of cycles: +26010C 101 seconds -40C Room temperature +85C Room temperature 5 cycles S6012_FM * 3/29/2017 7 Supercapacitors - FM Series Specifications - FMR Type cont'd Item High Temperature and High Humidity Resistance High Temperature Load FMR Type Capacitance Within 20% of initial value ESR Not to exceed 120% of initial ratings Current (30 minutes value) Not to exceed 120% of initial ratings Appearance No obvious abnormality Capacitance Within 30% of initial value ESR Below 200% of initial ratings Current (30 minutes value) Below 200% of initial ratings Appearance No obvious abnormality 5.5 V type: Voltage between terminal leads higher than 4.2 V Self Discharge Characteristics (Voltage Holding Characteristics) 3.5 V type: Not specified Test Conditions (conforming to JIS C 5160-1) Conforms to 4.14 Temperature: Relative humidity: Testing time: Conforms to 4.15 Temperature: Voltage applied: Series protection resistance: Testing time: Charging condition Voltage applied: Series resistance: Charging time: +402C 90 to 95% RH 2408 hours +852C Maximum operating voltage 0 1,000 +48 (+48/-0) hours 5.0 VDC (Terminal at the case side must be negative) 0 24 hours Storage Let stand for 24 hours in condition described below with terminals opened. Ambient Lower than 25C temperature: Lower than 70% RH Relative humidity: Marking Negative polarity identification Nominal capacitance Maximum operating voltage 5.5V - Polarity 473 A1 + E E: FME type marking L: FML type marking R: FMR type marking C: FMC type marking Date code (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com S6012_FM * 3/29/2017 8 Supercapacitors - FM Series Packaging Quantities Part Number Bulk Quantity per Box Straight Lead Bulk Quantity per Box L1 Lead Option Ammo Pack Quantity FM0H103ZF FM0H223ZF FM0H473ZF FM0H104ZF FM0H224ZF FM0V473ZF FM0V104ZF FM0V224ZF FM0J473ZF FME0H223ZF FME0H473ZF FML0H333ZF FMR0H473ZF FMR0H104ZF FMR0V104ZF FMC0H473ZF FMC0H104ZF FMC0H334ZF 1,000 pieces 1,000 pieces 1,000 pieces 1,000 pieces 1,000 pieces 1,000 pieces 1,000 pieces 1,000 pieces 1,000 pieces 1,000 pieces 1,000 pieces 1,000 pieces 1,000 pieces 1,000 pieces 1,000 pieces 1,000 pieces 1,000 pieces 400 pieces 1,000 pieces 1,000 pieces 1,000 pieces 800 pieces 800 pieces 1,000 pieces 1,000 pieces 1,000 pieces 1,000 pieces 1,000 pieces 1,000 pieces 1,000 pieces 1,000 pieces 1,000 pieces 1,000 pieces 1,000 pieces 1,000 pieces 300 pieces 1,000 pieces 1,000 pieces 1,000 pieces 1,000 pieces 1,000 pieces 1,000 pieces 1,000 pieces 1,000 pieces 1,000 pieces 1,000 pieces 1,000 pieces 1,000 pieces 1,000 pieces 1,000 pieces 1,000 pieces 1,000 pieces 1,000 pieces 400 pieces (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com S6012_FM * 3/29/2017 9 Supercapacitors - FM Series Ammo Pack Taping Format (Except FMC0H334ZFTP) P P2 h b a c + W4 W2 F - t3 W0 W1 L P1 + H - W t2 P0 D0 t1 Ammo Pack Taping Specifications (Except FMC0H334ZFTP) Item Symbol Dimensions (mm) Component Height a 11.50.5 Component Width b 10.50.5 Component Thickness c Refer to "Dimensions" table Lead-Wire Width W4 0.50.1 Lead-Wire Thickness t3 0.40.1 Component Pitch P 12.71.0 Sprocket Hole Pitch P0 12.70.3 Sprocket Hole Center to Lead Center P1 3.850.7 Sprocket Hole Center to Component Center P2 6.350.7 Lead Spacing F 5.00.5 Component Alignment (side/side) h 2.0 Maximum Carrier Tape Width W 18.0+1.0/-0.5 Hold-Down Tape Width W0 12.5 Minimum Sprocket Hole Position W1 9.00.5 Hold-Down Tape Position W2 3.0 Maximum Height to Seating Plane (lead length) H 16.00.5/18.00.5 Sprocket Hole Diameter D0 o 4.00.2 Carrier Tape Thickness t1 0.70.2 Total Thickness (Carrier Tape, Hold-Down Tape and Lead) t2 1.5 Maximum Cut Out Length L 11.0 Maximum (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com S6012_FM * 3/29/2017 10 Supercapacitors - FM Series Ammo Pack Taping Format (FMC0H334ZFTP) P P2 h b a c - - t3 W2 W4 H F + W W0 W1 L P1 + P0 D0 t2 t1 Ammo Pack Taping Specifications (FMC0H334ZFTP) Item Symbol Dimensions (mm) Component Height a 15.00.5 Component Width b 14.00.5 Component Thickness c 9.00.5 Lead-Wire Width W4 0.60.1 Lead-Wire Thickness t3 0.60.1 Component Pitch P 25.41.0 Sprocket Hole Pitch P0 12.70.3 Sprocket Hole Center to Lead Center P1 3.850.7 Sprocket Hole Center to Component Center P2 6.350.7 Lead Spacing F 5.00.5 Component Alignment (side/side) h 2.0 Maximum Carrier Tape Width W 18.0+1.0/-0.5 Hold-Down Tape Width W0 12.5 Minimum Sprocket Hole Position W1 9.00.5 Hold-Down Tape Position W2 3.0 Maximum Height to Seating Plane (lead length) H 16.00.5/18.00.5 Sprocket Hole Diameter D0 o 4.00.2 Carrier Tape Thickness t1 0.670.2 Total Thickness (Carrier Tape, Hold-Down Tape and Lead) t2 1.7 Maximum Cut Out Length L 11.0 Maximum (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com S6012_FM * 3/29/2017 11 Supercapacitors - FM Series List of Plating & Sleeve Type By changing the solder plating from leaded solder to lead-free solder and the outer tube material of can-cased conventional supercapacitor from polyvinyl chloride to polyethylene terephthalate (PET), our supercapacitor is now even friendlier to the environment. a. Iron + copper base + lead-free solder plating (Sn-1Cu) b. SUS nickel base + copper base + reflow lead-free solder plating (100% Sn, reflow processed) Series Part Number Plating Sleeve FM All FM Series a No tube used Sn/3.5Ag/0.75Cu Recommended Pb-free solder : Sn/3.0Ag/0.5Cu Sn/0.7Cu Sn/2.5Ag/1.0Bi/0.5Cu (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com S6012_FM * 3/29/2017 12 Supercapacitors - FM Series Measurement Conditions Capacitance (Charge System) Capacitance is calculated from expression (9) by measuring the charge time constant () of the capacitor (C). Prior to measurement, the capacitor is discharged by shorting both pins of the device for at least 30 minutes. In addition, use the polarity indicator on the device to determine correct orientation of capacitor for charging. Capacitance: C= Rc Eo: 3.0 (V) Product with maximum operating voltage of 3.5 V 5.0 (V) Product with maximum operating voltage of 5.5 V 6.0 (V) Product with maximum operating voltage of 6.5 V 10.0 (V) Product with maximum operating voltage of 11 V 12.0 (V) Product with maximum operating voltage of 12 V : Time from start of charging until Vc becomes 0.632 Eo (V) (seconds) Rc: See table below (). (F) (9) Switch Rc Eo C + - Charge Resistor Selection Guide Cap 0.010 F 0.022 F 0.033 F 0.047 F 0.10 F FA FE FS FYD Vc FY FYH FYL FR FM, FME FMR, FML - - - - - 5,000 - 1,000 - 1,000 2,000 2,000 2,000 2,000 - - - - - - - 1,000 1,000 1,000 2,000 1,000 2,000 1,000 510 510 510 1,000 510 - 1,000 0.22 F 200 200 200 510 510 - 0.33 F 0.47 F 1.0 F 1.4 F 1.5 F 2.2 F 2.7 F 3.3 F 4.7 F 5.0 F 5.6 F 10.0 F 22.0 F 50.0 F 100.0 F 200.0 F - 100 51 - - - - - - - - - - - - - - - 200 200 100 100 200 - - - 100 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 100 51 - 51 - - - - - - - - - - - - 100 100 - - - - - - 100 - - - - - - FMC 5,000 - 2,000 - Discharge - 2,000 1,000 1,000 1,000 0H: Discharge 510 - 0V: 1000 - - Discharge 200 - - 100 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - FG FGR FGH FT FC, FCS HV 5,000 - - 2,000 - - - - - 2,000 - - 1,000 Discharge 510 - Discharge - - Discharge - - - - - 1,000 Discharge 200 Discharge - - - - 1,000 Discharge 100 510 Discharge 100 - - - 510 - - 200 - 51 - - - - - 51 100 - - - - - - - 20 - - - - - - - - - - - - - - - - Discharge Discharge - - - - - - - - - - - - - - - Discharge - - - Discharge - Discharge - - Discharge Discharge Discharge Discharge Discharge *Capacitance values according to the constant current discharge method. *HV Series capacitance is measured by discharge system (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com S6012_FM * 3/29/2017 13 3.3F 4.7F 5.0F 5.6F - - - - - - - - - - 100 - - - - - - - - - - - - - - - - - - - - - - - - - *Capacitance values according to the constant current discharge method. *HV series capacitance is measured by discharge system. Supercapacitors - FM Series Table 3 Capacitance measurement - 100 - - 51 - - 20 - - - - - - - - Measurement Conditions cont'd Capacitance (Discharge System) Capacitance System) In Capacitance the (Discharge diagram below, charging is performed for a duration of 30 minutes, once the voltage of the condensor terminal (Discharge System:3.5V) As shown in the diagram below, charging is performed for a duration of 30 minutes once the voltage of the capacitor reaches 5.5 V. In the diagram below, charging is performed for a duration of 30 minutes, once the voltage of the capacitor terminal reaches 3.5V. terminalThen, reaches 5.5constant V. Then,current use a load constant current load device and for measure the time for the terminal to drop use a device and measure the time the terminal voltage to drop fromvoltage 3.0 to 2.5 V upon Then, use a constant current load device and measure the time for the terminal voltage to drop from 1.8 to 1.5V upon from 3.0 to 2.5 V upon discharge at 0.22 mA per 0.22 F, for example, and calculate the static capacitance according to the discharge at 0.22 at mA F, for example, andthe calculate the static capacitance to the shown equation shown below. discharge 1 for mA0.22 per 1F, and calculate static capacitance according according to the equation below. equation shown Note: Thebelow. current value is 1 mA discharged per 1F. Ix(T2T1)Ix(T2T1) C (F) CapactanceC V1V2 V1V2 (F) 3.5V SW 5.5V V (V) SW 0.22mA(I) A A C R C V R 3.5V 5.5V V1 V1 V2 Voltage Note: The current value is 1 mA discharged per 1 F. V2 V1 : 1.8V V1 : 3.0V V2 : 1.5V V1 : 2.5V 30 min. T2 T1 Duration (sec.) T1 Time T2 (sec.) 30 minutes Capacitance (Discharge System:3.5V) Capacitance (Discharge System:3.5V) Capacitance (Discharge System:3.5V) System:3.5V) Capacitance 36 Super Capacitors (Discharge Vol.13 Capacitance (Discharge System:HVseries) Capacitance (Discharge System 3.5 V)charging In below, is for of the voltage of In the diagram below, - charging is performed for a duration of 30 minutes, once theonce voltage the capacitor terminal terminal reaches reaches 3.5V. In the the diagram diagram below, charging is performed performed for a a duration duration of 30 30 minutes, minutes, the of voltage of the the capacitor capacitor In the diagram below, charging is performed for a duration of 30 minutes, once theonce voltage of the capacitor terminal terminal reaches reaches 3.5V. In the diagram below, charging isperformed performed for aameasure duration of 30 minutes, once the voltage ofof the capacitor terminal reaches Then, use a constant current load device and measure the time for the terminal voltage to drop from 1.8 to 1.5V As shown in the diagram below, charging is for duration of 30 minutes once the voltage the capacitor Then, use a constant current load device and the time for the terminal voltage to drop from 1.8 to 1.5V upon Then, use a constant load and device and measure for the terminal drop 1.8 to 1.5V Then, use a constant current current load device measure the timethe for time the terminal voltage voltage to drop to from 1.8from to 1.5V upon Max. operating voltage. discharge at 1 mA per 1F, and calculate the static capacitance according to the equation shown below. discharge at 1 mA per 1F, and calculate the static capacitance according to the equation shown below. 3.5 V. Then, use a constant current load device and measure the time for the terminal voltage to drop from terminal reaches discharge at 1 mA per 1F, and calculate the static capacitance according to the equation shown below. discharge at 1 mA per 1F, and calculate the static capacitance according to the equation shown below. Then,discharge use a constant and measure time forthe thestatic terminal voltage to drop from 2.0totothe 1.5V upon discharge 1.8 to 1.5 V upon at 1.0current mA perload 1.0device F, for example, andthe calculate capacitance according equation (V) (V) (V) below. (V) shown at 1 mA per 1F, and calculate the static capacitance according to the equation SW SW shown below. 3.5V SW V1 : 1.8V 3.5V V1 : 1.8V SW Ix(T Ix(T2T 1) 2T T11)) Ix(T 2T 1) 2(F) C C Ix(T C (F) V V 1 V VC 2 V V2 1 2 V11V 2 Ix(T 2T1) C (F) V1V2 (F) (F)3.5V 3.5V 3.5V 3.5V V 3.5V V V SW CV CV A A A A A C R C R C 3.5V (V) V1 V1 3.5V V2 R V2 R V1 3.5V V1 V1 V2 V2 V2 R V2 : 1.5V T2 T1 T2 T1 minutes 30 minutes 30 30 minutes 30 minutes T2 T1 Capacitance (Discharge System:HVseries) Capacitance (Discharge System:HVseries) Capacitance (Discharge System:HVseries) Capacitance (Discharge System:HVseries) V1 : 1.8V V2 : 1.5V V2 : 1.5V V1 : 1.8V V2 : 1.5V V2 : 1.5V V1 : 2.0V Time (sec.) 1 T2 TTime (sec.) Time (sec.) 1 T2 TTime (sec.) Time (sec.) 30 minutes In the diagram below, charging is performed for a duration of 30 minutes, the of voltage of the capacitor In the diagram below, charging is performed for a duration of 30 minutes, once theonce voltage the capacitor terminalterminal reachesre In the diagram below, charging is performed for a duration of 30 minutes, the of voltage of the capacitor In the diagram below,resistance charging is performed for a duration of 30 minutes, once theonce voltage the capacitor terminalterminal reachesre Equivalent series (ESR) Max. operating Max. operating voltage. voltage. Max.System operating voltage. Max. operating voltage. Capacitance ESR (Discharge - HV Series) beconstant calculated from the equation below. Then, use a constant current load device and measure time for terminal voltage to drop 2.0 to upon Then,shall use a current load device measure the time the for the voltage to drop from 2.0from to 1.5V discharge Then, use a constant current loadand device and measure the timeterminal for the the terminal voltage tothe drop from 2.0 upon to 1.5V 1.5V upon disc disc Then, use a constant current load device and measure the time for minutes the terminal voltage to drop of from 2.0 to 1.5V upon discharge As shown in the diagram below, charging is performed for a duration of 30 once the voltage capacitor at 1 mA per 1F, and calculate the static capacitance according to the equation shown below. at 1 mA per 1F, and calculate the static capacitance according to the equation shown below. at 11F, mAand per calculate 1F, and calculate the static capacitance according to the equation shown below. at 1 mA per the static capacitance according to the equation shown terminal reaches maximum operating voltage. Then, use a constant current load device andbelow. measure the time for the 10mA (V) (V) V C (V) the static capacitance according (V)calculate terminal voltage to drop from 2.0 to 1.5 V upon discharge at 1.0 mA per 1.0 F, and ESR () SWV f:1kHz C SW 3.5V SW V1 : 2.0V 3.5V V1 : 2.0V SW 3.5V A V1 : 2.0V A to the equation shown0.01 below. 3.5V V1 : 2.0V A A C Ix(T Ix(T2T 1) 2T T11)) Ix(T 2T 1) 2(F) C C Ix(T C C (F)2 1V V1V2 V V1V2 V1V2 (F) (F)3.5V 3.5V 3.5V V 3.5V V CV CV Current (at 30 minutes after charging) C R C R R R V1 V1 V2 V2 V1 V1 V2 V2 V2 : 1.5V V2 : 1.5V T1 V2 : 1.5V V2 : 1.5V T2 Time (sec.) (sec.) T2 TTime T1 Time (sec.) 1 T2 Current shall be calculated from the equation below. Time (sec.) T2 T1 minutes 30 minutes 30 30 minutes 30 minutes Prior to measurement, both lead terminals must be short-circuited for a minimum of 30 minutes. series resistance TheEquivalent lead terminal connected to the metal can(ESR) case is connected to the negative side of the power supply. Equivalent series resistance (ESR) Equivalent series resistance (ESR) Equivalent series resistance (ESR) ESR be the ESR shall be shall calculated from thefrom equation below. below. ESR be calculated calculated the equation equation ESR shall be shall calculated from thefrom equation below. below. Eo2.5Vdc (HVseries 50F) VR 2.7Vdc (HVseries except 50F) SW 10mA 10mA 10mA 10mA C VC(3.5V V 3.0Vdc type) V C V C () f:1kHz f:1kHz C C ESR ESR () VC V ESR C VC RCCC ESR () 0.01 V 0.01(5.5V 5.0Vdc type)() f:1kHz f:1kHz C 0.01 0.01 EO Rc1000 (0.010F, 0.022F, 0.047F) C 100 (0.10F, 0.22F, 0.47F) 10 (1.0F, 1.5F, 2.2F, 4.7F) Current 30 after Current (at 30 minutes after Current (at 30 minutes minutes after charging) charging) Current (at(HVseries) 30 (at minutes after charging) charging) 2.2 shall be calculated from the Current Current shall be calculated from the equation below. below. be calculated the equation equation Current Current shallVbe calculated from thefrom equation below. below. R shall Prior to measurement, both lead terminals be short-circuited for of minutes. Prior to measurement, both lead terminals must bemust short-circuited for a minimum of 30 minutes. Current (A) Prior to measurement, both lead terminals be short-circuited for a a minimum minimum of 30 30S6012_FM minutes.* 3/29/2017 Prior to measurement, both lead terminals must bemust short-circuited for a minimum of 30 minutes. R*CP.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 (c) KEMET Electronics Corporation * www.kemet.com lead terminal connected to the metal can case is connected to the negative side of the power The leadThe terminal connected to the metal can case is connected to the negative side of the power The lead terminal connected to the metal can case is connected to the negative side of thesupply. power supply. supply. The lead terminal connected to the metal can case is connected to the negative side of the power supply. Self-discharge characteristic (0H: 5.5V products) Eo(HVseries 2.5Vdc (HVseries Eo2.5Vdc 50F) 50F) Eo(HVseries 2.5Vdc (HVseries Eo2.5Vdc 50F) 50F) 14 at 1 mA per 1F, and calculate the static capacitance according to the equation shown below. (V) SW SW (V) A series resistance (ESR) T1) Ix(T2Equivalent A C (F) 3.5V C R V ) 2 ESR shall be calculated Ix(T2T V11V from the equation below. Supercapacitors - FM Series C (F) 3.5V C R V V1V2 Measurement Conditions cont'd ESR VC () 3.5V V1 V1 f:1kHz C T2 V1 : 2.0VV2 : 1.5V V2 V2 : 1.5V V2 T1 10mA 0.01 Equivalent series resistance (ESR) Equivalent Series Resistance (ESR) Equivalent series resistance (ESR) ESR shall be calculated from the equation below. T1 30 minutes V1 : 2.0V 3.5V 30 minutes T1 VC T2 T2 Time (sec.) Time (sec.) 30 minutes ESR shall be calculated from the equation below. ESR shall be calculated from the equation below. Current (at 30 minutes after charging) 10mA VC Current shall be calculated from the equation below. 10mA ESR () f:1kHz C VC VC 0.01 Prior to measurement, both lead terminals must be short-circuited for a minimum of 30 minute ESR () f:1kHz C VC 0.01 The lead terminal connected to the metal can case is connected to the negative side of the po 2.5Vdc (HVseries 50F) Current (at 30Eo minutes after charging) V Current (at 30 minutes after charging) 2.7Vdc (HVseries except 50F) SW Current (at 30 minutes after charging) Current shall be calculated from the equation below. 3.0Vdc (3.5V type) Current shall be calculated from the equation below. Prior to measurement, both lead terminals must be short-circuited for Prior to measurement, boththe lead terminals must be short-circuited for a minimum of 30 minutes. Current shall be calculated from equation below. R 5.0Vdcto (5.5V type) can case is connected to the negative side of the power a minimum of 30 minutes.Prior Theto lead terminal connected thethemetal The lead terminal connected to metal is connected the negative of the power measurement, both lead terminals mustcan be case short-circuited for of 30side minutes. supply. E atominimum Rc1000 (0.010F, 0.022F, 0.047F) C supply. The lead terminal connected to the metal can case is connected to the negative side of the power supply. R C O 100 (0.10F, 0.22F, 0.47F) Eo2.5Vdc (HVseries 50F) 10 (1.0F, 1.5F, 2.2F, 4.7F) VR Eo: 2.5 VDC (HV Series 50 F) 2.7Vdc (HVseries Eo2.5Vdc (HVseries 50F) except 50F) SW 2.7 VDC (HV Series except 50 F) 2.2 (HVseries) V R 3.0Vdc (3.5Vexcept type) 50F) 2.7Vdc (HVseries SW 3.0 VDC (3.5 V type) VR RC 5.0Vdc type) 3.0Vdc (3.5V (5.5V type) 5.0 VDC (5.5 V type) Current (A) EO R C0.047F) R C Rc 1000 (0.010F, 0.022F, 5.0Vdc C Rc: 1,000 (0.010 F, 0.022 F, 0.047 F) (5.5V type) EO 100 (0.10 F, 0.22 F,Rc 0.47 F) 100 (0.10F, 0.22F,0.047F) 0.47F) 1000 (0.010F, 0.022F, C 10 (1.0 F, 1.5 F, 2.2 F, 4.7100 F) 10 Self-discharge characteristic (0H: 5.5V products) (1.0F, 1.5F,0.47F) 2.2F, 4.7F) (0.10F, 0.22F, 2.2 (HV Series) 2.2 (HVseries) The self-discharge characteristic is measured by charging a voltage of 5.0 Vdc (charge protec 10 (1.0F, 1.5F, 2.2F, 4.7F) VRto the capacitor polarity for 24 hours, then releasing between the pins for 24 hours and measu 2.2 (HVseries) (A) Self-Discharge Characteristic Current (0H - 5.5 Products) VR V R CThe test should be carried out in an environment with an ambient temperature of 25 or belo Current (A)RH The self-discharge characteristic is measured by orcharging below. a voltage of 5.0 VDC (charge protection resistance: 0 ) RC polarity for 24 hours,characteristic then releasing between pinsproducts) for 24 hours and measuring the pin-toaccording to the capacitorSelf-discharge (0H: the 5.5V pin voltage. The test should be carried out in an environment with an ambient temperature of 25 C or below and relative Su Self-discharge characteristic 5.5V products) The self-discharge characteristic(0H: is measured by charging a voltage of 5.0 Vdc (charge protection resistance humidity of 70% RH or below. to the capacitor polarity for 24 hours, thenbyreleasing for 24 hoursprotection and measuring the pin-toThe self-discharge characteristic is measured chargingbetween a voltagethe of pins 5.0 Vdc (charge resistance: 0) the soldering is checked. test should befor carried out inthen an environment with anthe ambient temperature of 25 or below relativevo to theThe capacitor polarity 24 hours, releasing between pins for 24 hours and measuring theand pin-to-pin RHshould or below. The test be carried out in an environment with an ambient temperature of 25 or below and relative humid 4. Dismantling RH or below. There is a small amount of electrolyte stored within the capacitor. Do not attempt to dismantle as direct skin contactSuper with Capacito Super V the electrolyte will cause burning. This product should be treated as industrial waste and not is not to be disposed of byCapacitors fire. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com S6012_FM * 3/29/2017 15 Supercapacitors - FM Series Notes on Using Supercapacitors or Electric Double-Layer Capacitors (EDLCs) 1. Circuitry Design 1.1 Useful life The FC Series Supercapacitor (EDLC) uses an electrolyte in a sealed container. Water in the electrolyte can evaporate while in use over long periods of time at high temperatures, thus reducing electrostatic capacity which in turn will create greater internal resistance. The characteristics of the supercapacitor can vary greatly depending on the environment in which it is used. Basic breakdown mode is an open mode due to increased internal resistance. 1.2 Fail rate in the field Based on field data, the fail rate is calculated at approximately 0.006 Fit. We estimate that unreported failures are ten times this amount. Therefore, we assume that the fail rate is below 0.06 Fit. 1.3 Exceeding maximum usable voltage Performance may be compromised and in some cases leakage or damage may occur if applied voltage exceeds maximum working voltage. 1.4 Use of capacitor as a smoothing capacitor (ripple absorption) As supercapacitors contain a high level of internal resistance, they are not recommended for use as smoothing capacitors in electrical circuits. Performance may be compromised and, in some cases, leakage or damage may occur if a supercapacitor is used in ripple absorption. 1.5 Series connections As applied voltage balance to each supercapacitor is lost when used in series connection, excess voltage may be applied to some supercapacitors, which will not only negatively affect its performance but may also cause leakage and/or damage. Allow ample margin for maximum voltage or attach a circuit for applying equal voltage to each supercapacitor (partial pressure resistor/voltage divider) when using supercapacitors in series connection. Also, arrange supercapacitors so that the temperature between each capacitor will not vary. 1.6 Case Polarity The supercapacitor is manufactured so that the terminal on the outer case is negative (-). Align the (-) symbol during use. Even though discharging has been carried out prior to shipping, any residual electrical charge may negatively affect other parts. 1.7 Use next to heat emitters Useful life of the supercapacitor will be significantly affected if used near heat emitting items (coils, power transistors and posistors, etc.) where the supercapacitor itself may become heated. 1.8 Usage environment This device cannot be used in any acidic, alkaline or similar type of environment. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com S6012_FM * 3/29/2017 16 Supercapacitors - FM Series Notes on Using Supercapacitors or Electric Double-Layer Capacitors (EDLCs) cont'd 2. Mounting 2.1 Mounting onto a reflow furnace Except for the FC series, it is not possible to mount this capacitor onto an IR / VPS reflow furnace. Do not immerse the capacitor into a soldering dip tank. 2.2 Flow soldering conditions See Recommended Reflow Curves in Section - Precautions for Use 2.3 Installation using a soldering iron Care must be taken to prevent the soldering iron from touching other parts when soldering. Keep the tip of the soldering iron under 400C and soldering time to within 3 seconds. Always make sure that the temperature of the tip is controlled. Internal capacitor resistance is likely to increase if the terminals are overheated. 2.4 Lead terminal processing Do not attempt to bend or polish the capacitor terminals with sand paper, etc. Soldering may not be possible if the metallic plating is removed from the top of the terminals. 2.5 Cleaning, Coating, and Potting Except for the FM series, cleaning, coating and potting must not be carried out. Consult KEMET if this type of procedure is necessary. Terminals should be dried at less than the maximum operating temperature after cleaning. 3. Storage 3.1 Temperature and humidity Make sure that the supercapacitor is stored according to the following conditions: Temperature: 5 - 35C (Standard 25C), Humidity: 20 - 70% (Standard: 50%). Do not allow the build up of condensation through sudden temperature change. 3.2 Environment conditions Make sure there are no corrosive gasses such as sulfur dioxide, as penetration of the lead terminals is possible. Always store this item in an area with low dust and dirt levels. Make sure that the packaging will not be deformed through heavy loading, movement and/or knocks. Keep out of direct sunlight and away from radiation, static electricity and magnetic fields. 3.3 Maximum storage period This item may be stored up to one year from the date of delivery if stored at the conditions stated above. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com S6012_FM * 3/29/2017 17 Supercapacitors - FM Series KEMET Electronic Corporation Sales Offices For a complete list of our global sales offices, please visit www.kemet.com/sales. Disclaimer All product specifications, statements, information and data (collectively, the "Information") in this datasheet are subject to change. The customer is responsible for checking and verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed. All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on KEMET Electronics Corporation's ("KEMET") knowledge of typical operating conditions for such applications, but are not intended to constitute - and KEMET specifically disclaims - any warranty concerning suitability for a specific customer application or use. The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by KEMET with reference to the use of KEMET's products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained. Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product-related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other measures may not be required. KEMET is a registered trademark of KEMET Electronics Corporation. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com S6012_FM * 3/29/2017 18