e ADVANCED LINEAR DEVICES, INC. EN APPLICATIONS ALD110808A/ALD110808/ALD110908A/ALD110908 are monolithic quad/ dual N-Channel MOSFETs matched at the factory using ALD's proven EPAD(R) CMOS technology. These devices are intended for low voltage, small signal applications. * Precision current mirrors * Precision current sources * Voltage choppers * Differential amplifier input stage * Voltage comparator * Voltage bias circuits * Sample and Hold * Analog inverter * Level shifters * Source followers and buffers * Current multipliers * Analog switches / multiplexers These MOSFET devices are built on the same monolithic chip, so they exhibit excellent temperature tracking characteristics. They are versatile as circuit elements and are useful design component for a broad range of analog applications. They are basic building blocks for current sources, differential amplifier input stages, transmission gates, and multiplexer applications. For most applications, connect V- and N/C pins to the most negative voltage potential in the system and V+ pin to the most positive voltage potential (or left open unused). All other pins must have voltages within these voltage limits. ALD110808/ALD110908 devices are built for minimum offset voltage and differential thermal response, and they are suited for switching and amplifying applications in +1.0V to +10V (+/- 5 V) systems where low input bias current, low input capacitance and fast switching speed are desired. As these are MOSFET devices, they feature very large (almost infinite) current gain in a low frequency, or near DC, operating environment. These devices are suitable for use in precision applications which require very high current gain, beta, such as current mirrors and current sources. The high input impedance and the high DC current gain of the Field Effect Transistors result from extremely low current loss through the control gate. The DC current gain is limited by the gate input leakage current, which is specified at 30pA at room temperature. For example, DC beta of the device at a drain current of 3mA and input leakage current of 30pA at 25C is = 3mA/30pA = 100,000,000. PIN CONFIGURATION ALD110808 N/C* 1 GN1 2 DN1 3 S12 4 V- 5 DN4 6 FEATURES GN4 7 * Enhancement-mode (normally off) * Standard Gate Threshold Voltages: +0.8V * Matched MOSFET to MOSFET characteristics * Tight lot to lot parametric control * Low input capacitance * VGS(th) match to 2mV and 10mV * High input impedance -- 1012 typical * Positive,zero, and negative VGS(th) temperature coefficient * DC current gain >108 * Low input and output leakage currents N/C* 8 N/C* 1 ORDERING INFORMATION GN1 2 Operating Temperature Range* 0C to +70C 0C to +70C ALD110808APC ALD110808 PC AB LE D VGS(th)= +0.8V GENERAL DESCRIPTION 16-Pin SOIC Package (R) ALD110808/ALD110808A/ALD110908/ALD110908A QUAD/DUAL N-CHANNEL ENHANCEMENT MODE EPAD(R) MATCHED PAIR MOSFET ARRAY 16-Pin Plastic Dip Package TM EPAD 8-Pin Plastic Dip Package 8Pin SOIC Package ALD110808ASC ALD110908APA ALD110908ASA ALD110808SC ALD110908PA ALD110908SA V- V- M1 M2 V+ VM4 M3 V- V- 16 N/C* 15 GN2 14 DN2 13 V+ 12 S34 11 DN3 10 GN3 9 N/C* 8 N/C* 7 GN2 6 DN2 5 V- PC, SC PACKAGES ALD110908 DN1 3 S12 4 V- V- M1 M2 V- PA, SA PACKAGES *N/C pins are internally connected. Connect to V- to reduce noise * Contact factory for industrial or military temp. ranges or user-specified threshold voltage values. Rev 1.0-0506 (c)2 005 Advanced Linear Devices, Inc. 415 Tasman Drive, Sunnyvale, California 94089-1706 Tel: (408) 747-1155 Fax: (408) 747-1286 www.aldinc.com ABSOLUTE MAXIMUM RATINGS Drain-Source voltage, VDS Gate-Source voltage, VGS Power dissipation Operating temperature range PA, SA, PC, SC package Storage temperature range Lead temperature, 10 seconds 10.6V 10.6V 500 mW 0C to +70C -65C to +150C +260C OPERATING ELECTRICAL CHARACTERISTICS V+ = +5V (or open) V- = GND TA = 25C unless otherwise specified CAUTION: ESD Sensitive Device. Use static control procedures in ESD controlled environment. ALD110808A / ALD110908A Parameter Symbol Min 0.78 Typ ALD110808/ ALD110908 Max Min Typ 0.80 0.82 0.78 0.80 0.82 2 3 10 Gate Threshold Voltage VGS(th) Offset Voltage VGS1-VGS2 VOS 1 VGS1-VGS2 Tempco VOS 5 GateThreshold Tempco VGS(th) On Drain Current IDS (ON) Forward Transconductance Max 5 -1.7 0.0 +1.6 -1.7 0.0 +1.6 12.0 3.0 12.0 3.0 GFS 1.4 Transconductance Mismatch GFS Output Conductance GOS Drain Source On Resistance Unit Test Condition V IDS =1A VDS = 0.1V mV IDS=1A V/ C VDS1= VDS2 mV/ C ID= 1A ID= 20A VDS = 0.1V ID= 40A mA VGS= +10.3V VGS= +4.8V VDS= +5V 1.4 mmho VGS = +4.8V VDS = +9.8V 1.8 1.8 % 68 68 mho VGS =+4.8V VDS = +9.8V RDS (ON) 500 500 VDS = 0.1V VGS = +4.8V Drain Source On Resistance Mismatch RDS (ON) 0.5 0.5 % Drain Source Breakdown Voltage BVDSX Drain Source Leakage Current1 IDS (OFF) Gate Leakage Current1 10 10 V IDS = 1.0A VGS = -0.2V 10 100 4 10 100 4 pA nA VGS = -0.2V VDS =10V, TA = 125C IGSS 3 30 1 3 30 1 pA nA VDS = 0V VGS = 10V TA =125C Input Capacitance CISS 2.5 2.5 pF Transfer Reverse Capacitance CRSS 0.1 0.1 pF Turn-on Delay Time ton 10 10 ns V+ = 5V RL= 5K Turn-off Delay Time toff 10 10 ns V+ = 5V RL= 5K 60 60 dB f = 100KHz Crosstalk Notes: 1 Consists of junction leakage currents ALD110808/ALD110808A/ALD110908/ALD110908A Advanced Linear Devices 2