LT8705A 80V VIN and VOUT Synchronous 4-Switch BuckBoost DC/DC Controller Features Description Single Inductor Allows VIN Above, Below, or Equal to Regulated VOUT nn V Range 2.8V (Need EXTV IN CC > 6.4V) to 80V nn V OUT Range: 1.3V to 80V nn Quad N-Channel MOSFET Gate Drivers nn Synchronous Rectification: Up to 98% Efficiency nn Input and Output Current Monitor Pins nn Synchronizable Fixed Frequency: 100kHz to 400kHz nn Integrated Input Current, Input Voltage, Output Current and Output Voltage Feedback Loops nn Improved Light Load Transition from DCM to FCM nn Improved IMON_OUT, IMON_IN Offset When Cold nn Clock Output Usable To Monitor Die Temperature The LT(R)8705A is a high performance buck-boost switching regulator controller that operates from input voltages above, below or equal to the output voltage. The part has integrated input current, input voltage, output current and output voltage feedback loops. With a wide 2.8V to 80V input and 1.3V to 80V output range, the LT8705A is compatible with most solar, automotive, telecom and battery-powered systems. The LT8705A is an improved pin compatible version of the LT8705 and is recommended for new designs. See LT8705A vs LT8705 in the Applications Information section for more information. nn The LT8705A includes a MODE pin to select among Burst Mode(R) operation, discontinuous or continuous conduction mode at light loads. Additional features include a 3.3V/12mA LDO, a synchronizable fixed operating frequency, and onboard gate drivers. Applications nn nn High Voltage Buck-Boost Converters Input or Output Current Limited Converters L, LT, LTC, LTM, Linear Technology, Burst Mode, Module and the Linear logo are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. Typical Application Telecom Voltage Stabilizer M1 x2 + 22H 4.7F x4 220F x2 M3 x2 M2 TO DIODE 0.22F 2 x2 TG1 BOOST1 SW1 BG1 CSP M4 1nF 10 1nF 10 CSN CSPOUT CSPIN CSNOUT 4.7F SRVO_FBOUT SRVO_IIN SS SRVO_IOUT 1F VC CLKOUT SYNC IMON_OUT 4 90 3 2 85 80 1 VOUT = 48V ILOAD = 2A 4 TO TO BOOST1 BOOST2 POWER LOSS (W) 4.7F SRVO_FBIN IMON_IN 4.7F 10k INTVCC GATEVCC LT8705A RT 215k 5 FBOUT SWEN 6 95 EXTVCC SHDN FBIN 20k 100 GND BG2 SW2 BOOST2 TG2 MODE 71.5k Efficiency and Power Loss 392k CSNIN LDO33 VOUT 48V 220F 5A x2 0.22F VIN 100k 4.7F x6 TO DIODE 10m 2 x2 + EFFICIENCY (%) VIN 36V TO 80V 30 40 50 60 VIN (V) 70 80 0 8705A TA01b 56.2k 1F 220pF 3.3nF 202kHz 8705A TA01 8705af For more information www.linear.com/LT8705A 1 LT8705A Absolute Maximum Ratings (Note 1) VCSP-VCSN, VCSPIN-VCSNIN, VCSPOUT-VCSNOUT...................................... -0.3V to 0.3V SS, CLKOUT, CSP, CSN Voltage.................... -0.3V to 3V VC Voltage (Note 2).................................... -0.3V to 2.2V RT, LDO33, FBOUT Voltage........................... -0.3V to 5V IMON_IN, IMON_OUT Voltage...................... -0.3V to 5V SYNC Voltage............................................. -0.3V to 5.5V INTVCC, GATEVCC Voltage............................. -0.3V to 7V VBOOST1-VSW1, VBOOST2-VSW2...................... -0.3V to 7V SWEN, MODE Voltage................................... -0.3V to 7V SRVO_FBIN, SRVO_FBOUT Voltage............ -0.3V to 30V SRVO_IIN, SRVO_IOUT Voltage.................. -0.3V to 30V FBIN, SHDN Voltage.................................... -0.3V to 30V CSNIN, CSPIN, CSPOUT, CSNOUT Voltage...-0.3V to 80V VIN, EXTVCC Voltage................................... -0.3V to 80V SW1, SW2 Voltage.......................................81V (Note 7) BOOST1, BOOST2 Voltage.......................... -0.3V to 87V BG1, BG2, TG1, TG2............................................ (Note 6) Operating Junction Temperature Range LT8705AE (Notes 3, 8)........................ -40C to 125C LT8705AI (Notes 3, 8)......................... -40C to 125C LT8705AH (Notes 3, 8)....................... -40C to 150C LT8705AMP (Notes 3, 8).................... -55C to 150C Storage Temperature Range................... -65C to 150C Lead Temperature (Soldering, 10 sec) FE Package........................................................ 300C Pin Configuration INTVCC 1 38 VIN CSNIN TOP VIEW MODE 2 37 CSPIN IMON_IN 3 36 CSNIN 38 37 36 35 34 33 32 SHDN 4 CSPIN VIN INTVCC SWEN MODE IMON_IN TOP VIEW SHDN 1 31 CSPOUT CSN 5 CSN 2 30 CSNOUT CSP 6 CSP 3 29 EXTVCC LDO33 7 FBIN 8 FBOUT 9 28 SRVO_FBOUT LDO33 4 27 SRVO_IOUT FBIN 5 FBOUT 6 26 SRVO_IIN 39 GND IMON_OUT 7 IMON_OUT 10 25 SRVO_FBIN VC 8 24 NC SS 9 23 BOOST1 CLKOUT 10 22 TG1 SYNC 11 21 SW1 VC 11 CLKOUT 13 SW2 TG2 BOOST2 BG2 GATEVCC BG1 GND 30 EXTVCC 39 GND 28 BOOST1 26 TG1 SYNC 14 RT 15 24 SW1 GND 16 13 14 15 16 17 18 19 UHF PACKAGE 38-LEAD (5mm x 7mm) PLASTIC QFN TJMAX = 125C, JA = 34C/W EXPOSED PAD (PIN 39) IS GND, MUST BE SOLDERED TO PCB 32 CSNOUT SS 12 20 NC RT 12 34 CSPOUT BG1 17 22 SW2 GATEVCC 18 21 TG2 BG2 19 20 BOOST2 FE PACKAGE VARIATION: FE38(31) 38-LEAD PLASTIC TSSOP TJMAX = 125C, JA = 25C/W EXPOSED PAD (PIN 39) IS GND, MUST BE SOLDERED TO PCB 8705af 2 For more information www.linear.com/LT8705A LT8705A Order Information http://www.linear.com/product/LT8705A#orderinfo LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LT8705AEUHF#PBF LT8705AEUHF#TRPBF 8705A 38-Lead (5mm x 7mm) Plastic QFN -40C to 125C LT8705AIUHF#PBF LT8705AIUHF#TRPBF 8705A 38-Lead (5mm x 7mm) Plastic QFN -40C to 125C LT8705AEFE#PBF LT8705AEFE#TRPBF LT8705AFE 38-Lead Plastic TSSOP -40C to 125C LT8705AIFE#PBF LT8705AIFE#TRPBF LT8705AFE 38-Lead Plastic TSSOP -40C to 125C LT8705AHFE#PBF LT8705AHFE#TRPBF LT8705AFE 38-Lead Plastic TSSOP -40C to 150C LT8705AMPFE#PBF LT8705AMPFE#TRPBF LT8705AFE 38-Lead Plastic TSSOP -55C to 150C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/. Some packages are available in 500 unit reels through designated sales channels with #TRMPBF suffix. Electrical Characteristics The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VIN = 12V, SHDN = 3V unless otherwise noted. (Note 3) PARAMETER CONDITIONS MIN TYP MAX UNITS Voltage Supplies and Regulators VIN Operating Voltage Range EXTVCC = 0V EXTVCC = 7.5V VIN Quiescent Current Not Switching, VEXTVCC = 0 VIN Quiescent Current in Shutdown VSHDN = 0V EXTVCC Switchover Voltage IINTVCC = 20mA, VEXTVCC Rising l l 5.5 2.8 4.2 mA l 6.15 0 1 A 6.4 6.6 V 0.18 Maximum Current Draw from INTVCC and LDO33 Pins Combined. Regulated from VIN or EXTVCC (12V) l INTVCC = 5.25V l INTVCC = 4.5V INTVCC Voltage Regulated from VIN, IINTVCC = 20mA Regulated from EXTVCC (12V), IINTVCC = 20mA INTVCC Load Regulation IINTVCC = 0mA to 50mA INTVCC, GATEVCC Undervoltage Lockout INTVCC Falling, GATEVCC Connected to INTVCC INTVCC, GATEVCC Undervoltage Lockout Hysteresis GATEVCC Connected to INTVCC INTVCC Regulator Dropout Voltage VIN-VINTVCC, IINTVCC = 20mA LDO33 Pin Voltage 5mA from LDO33 Pin LDO33 Pin Load Regulation ILDO33 = 0.1mA to 5mA LDO33 Pin Current Limit LDO33 Pin Undervoltage Lockout V V 2.65 EXTVCC Switchover Hysteresis INTVCC Current Limit 80 80 l l l l l LDO33 Falling V 90 28 127 42 165 55 mA mA 6.15 6.15 6.35 6.35 6.55 6.55 V V -0.5 -1.5 % 4.65 4.85 V 4.45 3.23 160 mV 245 mV 3.295 3.35 V -0.25 -1 % 12 17.25 22 mA 2.96 3.04 3.12 LDO33 Pin Undervoltage Lockout Hysteresis 35 V mV Switching Regulator Control Maximum Current Sense Threshold (VCSP - VCSN) Maximum Current Sense Threshold (VCSN - VCSP) Boost Mode, Minimum M3 Switch Duty Cycle (LT8705AE, LT8705AI) (LT8705AH, LT8705AMP) l l 102 100 117 117 132 134 mV mV Buck Mode, Minimum M2 Switch Duty Cycle (LT8705AE, LT8705AI) (LT8705AH, LT8705AMP) l l 69 67 86 86 102 104 mV mV 8705af For more information www.linear.com/LT8705A 3 LT8705A Electrical Characteristics The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VIN = 12V, SHDN = 3V unless otherwise noted. (Note 3) PARAMETER CONDITIONS Gain from VC to Maximum Current Sense Voltage (VCSP-VCSN) (A5 in the Block Diagram) Boost Mode Buck Mode SHDN Input Voltage High SHDN Rising to Enable the Device MIN TYP MAX 150 -150 l mV/V mV/V 1.184 1.234 1.284 SHDN Input Voltage High Hysteresis 50 SHDN Input Voltage Low Device Disabled, Low Quiescent Current (LT8705AE, LT8705AI) (LT8705AH, LT8705AMP) SHDN Pin Bias Current l l VSHDN = 3V VSHDN = 12V SWEN Rising Threshold Voltage (Note 5) 0 11 l 0.35 0.3 V V 1 22 A A 22 MODE Pin Forced Continuous Mode Threshold l 0.4 MODE Pin Burst Mode Range l 1.0 MODE Pin Discontinuous Mode Threshold l Soft-Start Charging Current VSS = 0.5V Soft-Start Discharge Current VSS = 0.5V 13 V mV 1.156 1.206 1.256 SWEN Threshold Voltage Hysteresis (Note 5) UNITS V mV V 19 1.7 V 2.3 V 25 A 9.5 A Voltage Regulator Loops (Refer to Block Diagram to Locate Amplifiers) Regulation Voltage for FBOUT VC = 1.2V (LT8705AE, LT8705AI) VC = 1.2V (LT8705AH, LT8705AMP) l l 1.193 1.207 1.222 1.191 1.207 1.222 V V Regulation Voltage for FBIN VC = 1.2V (LT8705AE, LT8705AI) VC = 1.2V (LT8705AH, LT8705AMP) l l 1.184 1.205 1.226 1.182 1.205 1.226 V V Line Regulation for FBOUT and FBIN Error Amp Reference Voltage VIN = 12V to 80V; Not Switching 0.002 0.005 %/V FBOUT Pin Bias Current Current Out of Pin 15 nA FBOUT Error Amp EA4 gm 315 mho FBOUT Error Amp EA4 Voltage Gain 220 V/V 10 nA FBIN Error Amp EA3 gm 130 mho FBIN Error Amp EA3 Voltage Gain 90 V/V FBIN Pin Bias Current Current Out of Pin SRVO_FBIN Activation Threshold (Note 5) (VFBIN Falling) - (Regulation Voltage for FBIN), VFBOUT = VIMON_IN = VIMON_OUT = 0V SRVO_FBIN Activation Threshold Hysteresis (Note 5) VFBOUT = VIMON_IN = VIMON_OUT = 0V SRVO_FBOUT Activation Threshold (Note 5) (VFBOUT Rising) - (Regulation Voltage for FBOUT), VFBIN = 3V, VIMON_IN = VIMON_OUT = 0V SRVO_FBOUT Activation Threshold Hysteresis (Note 5) VFBIN = 3V, VIMON_IN = 0V, VIMON_OUT = 0V SRVO_FBIN, SRVO_FBOUT Low Voltage (Note 5) I = 100A l 110 330 mV SRVO_FBIN, SRVO_FBOUT Leakage Current (Note 5) VSRVO_FBIN = VSRVO_FBOUT = 2.5V l 0 1 A l 1.187 1.208 1.229 V 0.002 0.005 %/V 56 72 89 33 -37 -29 mV mV -21 15 mV mV Current Regulation Loops (Refer to Block Diagram to Locate Amplifiers) Regulation Voltages for IMON_IN and IMON_OUT VC = 1.2V Line Regulation for IMON_IN and IMON_OUT Error Amp Reference Voltage VIN = 12V to 80V; Not Switching CSPIN, CSNIN Bias Current BOOST Capacitor Charge Control Block Not Active ICSPIN + ICSNIN, VCSPIN = VCSNIN = 12V 31 A 8705af 4 For more information www.linear.com/LT8705A LT8705A Electrical Characteristics The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VIN = 12V, SHDN = 3V unless otherwise noted. (Note 2) PARAMETER CONDITIONS MIN TYP MAX UNITS CSPIN, CSNIN Common Mode Operating Voltage Range l 1.5 80 V CSPIN, CSNIN Differential Operating Voltage Range l -100 100 mV l l 0.95 0.94 0.93 1.05 1.06 1.07 mmho mmho mmho IMON_IN Maximum Output Current l 100 IMON_IN Overvoltage Threshold l 1.55 VCSPIN-CSNIN to IMON_IN Amplifier A7 gm VCSPIN - VCSNIN = 50mV, VCSPIN = 5.025V (All Grades) (LT8705AE, LT8705AI) (LT8705AH, LT8705AMP) 1 1 1 A 1.61 1.67 V IMON_IN Error Amp EA2 gm 185 mho IMON_IN Error Amp EA2 Voltage Gain 130 V/V 45 4 A A CSPOUT, CSNOUT Bias Current BOOST Capacitor Charge Control Block Not Active ICSPOUT + ICSNOUT, VCSPOUT = VCSNOUT = 12V ICSPOUT + ICSNOUT, VCSPOUT = VCSNOUT = 1.5V CSPOUT, CSNOUT Common Mode Operating Voltage Range l 0 80 V CSPOUT, CSNOUT Differential Mode Operating Voltage Range l -100 100 mV l l 0.95 0.94 0.93 1 1 1 1.05 1.085 1.095 mmho mmho mmho l l 0.65 0.55 0.5 1 1 1 1.35 1.6 1.65 mmho mmho mmho IMON_OUT Maximum Output Current l 100 IMON_OUT Overvoltage Threshold l 1.55 VCSPOUT-CSNOUT to IMON_OUT Amplifier A6 gm VCSPOUT - VCSNOUT = 50mV, VCSPOUT = 5.025V (All Grades) (LT8705AE, LT8705AI) (LT8705AH, LT8705AMP) VCSPOUT - VCSNOUT = 5mV, VCSPOUT = 5.0025V (All Grades) (LT8705AE, LT8705AI) (LT8705AH, LT8705AMP) A 1.61 1.67 V IMON_OUT Error Amp EA1 gm 185 mho IMON_OUT Error Amp EA1 Voltage Gain 130 V/V SRVO_IIN Activation Threshold (Note 5) (VIMON_IN Rising) - (Regulation Voltage for IMON_IN), VFBIN = 3V, VFBOUT = 0V, VIMON_OUT = 0V SRVO_IIN Activation Threshold Hysteresis (Note 5) VFBIN = 3V, VFBOUT = 0V, VIMON_OUT = 0V SRVO_IOUT Activation Threshold (Note 5) (VIMON_OUT Rising) - (Regulation Voltage for IMON_ OUT), VFBIN = 3V, VFBOUT = 0V, VIMON_IN = 0V SRVO_IOUT Activation Threshold Hysteresis (Note 5) VFBIN = 3V, VFBOUT = 0V, VIMON_IN = 0V SRVO_IIN, SRVO_IOUT Low Voltage (Note 5) I = 100A l 110 330 mV SRVO_IIN, SRVO_IOUT Leakage Current (Note 5) VSRVO_IIN = VSRVO_IOUT = 2.5V l 0 1 A -60 -49 -37 22 -62 -51 mV mV -39 22 mV mV NMOS Gate Drivers TG1, TG2 Rise Time CLOAD = 3300pF (Note 4) 20 ns TG1, TG2 Fall Time CLOAD = 3300pF (Note 4) 20 ns BG1, BG2 Rise Time CLOAD = 3300pF (Note 4) 20 ns BG1, BG2 Fall Time CLOAD = 3300pF (Note 4) 20 ns TG1 Off to BG1 On Delay CLOAD = 3300pF Each Driver 100 ns BG1 Off to TG1 On Delay CLOAD = 3300pF Each Driver 80 ns TG2 Off to BG2 On Delay CLOAD = 3300pF Each Driver 100 ns 8705af For more information www.linear.com/LT8705A 5 LT8705A Electrical Characteristics The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VIN = 12V, SHDN = 3V unless otherwise noted. (Note 3) PARAMETER CONDITIONS BG2 Off to TG2 On Delay CLOAD = 3300pF Each Driver MIN TYP 80 MAX UNITS ns Minimum On-Time for Main Switch in Boost Operation (tON(M3,MIN)) Switch M3, CLOAD = 3300pF 265 ns Minimum On-Time for Synchronous Switch in Buck Operation (tON(M2,MIN)) Switch M2, CLOAD = 3300pF 260 ns Minimum Off-Time for Main Switch in Steady-State Boost Operation Switch M3, CLOAD = 3300pF 245 ns Minimum Off-Time for Synchronous Switch in Steady-State Buck Operation Switch M2, CLOAD = 3300pF 245 ns Oscillator Switch Frequency Range SYNCing or Free Running Switching Frequency, fOSC RT = 365k RT = 215k RT = 124K 100 l l l 102 170 310 SYNC High Level for Synchronization l 1.3 SYNC Low Level for Synchronization l SYNC Clock Pulse Duty Cycle VSYNC = 0V to 2V 120 202 350 kHz 142 235 400 kHz kHz kHz V 0.5 V 80 % 2.45 2.55 V 25 100 mV 20 Recommended Minimum SYNC Ratio fSYNC/fOSC 400 3/4 CLKOUT Output Voltage High 1mA Out of CLKOUT Pin CLKOUT Output Voltage Low 1mA Into CLKOUT Pin CLKOUT Duty Cycle TJ = -40C TJ = 25C TJ = 125C CLKOUT Rise Time 2.3 22.7 44.1 77 % % % CLOAD = 200pF 30 ns CLKOUT Fall Time CLOAD = 200pF 25 ns CLKOUT Phase Delay SYNC Rising to CLKOUT Rising, fOSC = 100kHz Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: Do not force voltage on the VC pin. Note 3: The LT8705AE is guaranteed to meet performance specifications from 0C to 125C junction temperature. Specifications over the -40C to 125C operating junction temperature range are assured by design, characterization and correlation with statistical process controls. The LT8705AI is guaranteed over the full -40C to 125C junction temperature range. The LT8705AH is guaranteed over the full -40C to 150C operating junction temperature range. The LT8705AMP is guaranteed over the full -55C to 150C operating junction temperature range. Operating lifetime is derated at junction temperatures greater than 125C. Note 4: Rise and fall times are measured using 10% and 90% levels. Delay times are measured using 50% levels. l 160 180 200 Deg Note 5: This specification not applicable in the FE38 package. Note 6: Do not apply a voltage or current source to these pins. They must be connected to capacitive loads only, otherwise permanent damage may occur. Note 7: Negative voltages on the SW1 and SW2 pins are limited, in an application, by the body diodes of the external NMOS devices, M2 and M3, or parallel Schottky diodes when present. The SW1 and SW2 pins are tolerant of these negative voltages in excess of one diode drop below ground, guaranteed by design. Note 8: This IC includes overtemperature protection that is intended to protect the device during momentary overload conditions. Junction temperature will exceed the maximum operating junction temperature when overtemperature protection is active. Continuous operation above the specified maximum operating junction temperature may impair device reliability. 8705af 6 For more information www.linear.com/LT8705A LT8705A Typical Performance Characteristics Efficiency vs Output Current (Boost Region-Figure 15) Efficiency vs Output Current (Buck-Boost Region-Figure 15) 100 100 90 90 80 80 70 70 70 60 50 40 VIN = 36V VOUT = 48V BURST FCM DCM 20 10 1000 100 LOAD CURRENT (mA) 10 60 50 40 VIN = 48V VOUT = 48V BURST FCM DCM 30 20 10 0 10000 1000 100 LOAD CURRENT (mA) 10 VC = 1.2V 0 1.19 IMON_OUT IMON_IN FBOUT FBIN 1.18 1.17 -55 -30 -5 VC = 1.2V 300 1.21 1.20 1.19 1.17 -45 BUCK REGION 40 20 0 20 40 60 80 M2 OR M3 DUTY CYCLE (%) 100 55 30 80 5 TEMPERATURE (C) -20 105 0 -40 -20 130 0 20 40 60 80 TEMPERATURE (C) 120 120 100 100 80 80 60 60 40 40 BUCK REGION 20 20 BOOST REGION 0 0 -20 -20 -40 -40 -60 -60 -80 0.5 1.5 1 100 120 8705A G06 Maximum Inductor Current Sense Voltage at Minimum Duty Cycle 2 -80 VC (V) 8705A G07 RT = 365k 50 8705A G08 120 BOOST REGION 100 CSP-CSN (mV) CSN-CSP (mV) 100 60 150 Inductor Current Sense Voltage at Minimum Duty Cycle 140 BOOST REGION RT = 215k 200 8705A G05 Maximum Inductor Current Sense Voltage vs Duty Cycle 80 250 100 8705A G04 120 RT = 124k 350 1.18 20 45 70 95 120 145 TEMPERATURE (C) 10000 Oscillator Frequency 400 FREQUENCY (kHz) 1.20 1000 100 LOAD CURRENT (mA) 10 8705A G03 1.22 FBOUT VOLTAGE (V) PIN VOLTAGE (V) 1.22 0 10 FBOUT Voltages (Five Parts) 1.23 1.21 VIN = 72V VOUT = 48V BURST FCM DCM 8705A G02 Feedback Voltages 1.23 50 40 20 10000 8705A G01 60 30 |CSP-CSN| (mV) 0 EFFICIENCY (%) 90 80 30 |CSP-CSN| (mV) Efficiency vs Output Current (Buck Region-Figure 15) 100 EFFICIENCY (%) EFFICIENCY (%) TA = 25C unless otherwise specified. 80 BUCK REGION 60 40 20 0 -40 -20 0 20 40 60 80 TEMPERATURE (C) 100 120 8705A G09 8705af For more information www.linear.com/LT8705A 7 LT8705A Typical Performance Characteristics Minimum Inductor Current Sense Voltage in Forced Continuous Mode INTVCC Line Regulation (EXTVCC = 0V) 0 7.0 6.5 BUCK REGION -40 6.5 -60 -80 5.5 4.5 -120 0 20 40 60 4.0 100 80 M2 OR M3 DUTY CYCLE (%) 6 4 8 10 12 14 VIN (V) 16 3.5 MAXIMUM VC (V) IIN (mA) 1.0 0.8 0.6 2.0 1.5 125C 25C -40C 0.5 0.2 0 0.2 0.4 0.6 0.8 SS (V) 1.0 1.2 0 1.4 5 15 25 35 45 VIN (V) 55 65 150 125 100 75 50 25 0 -25 -100 75 8705A G14 8705A G13 LDO33 Pin Regulation (ILDO33 = 1mA) CLKOUT Duty Cycle -50 0 50 200 100 150 CSPIN-CSNIN (mV) CSPOUT-CSNOUT (mV) 8705A G15 SHDN and SWEN Pin Thresholds vs Temperature 3.5 100 12 175 1.0 0.4 0 GATEVCC CONNECTED TO INTVCC 2.5 1.2 10 IMON Output Currents 3.0 BUCK REGION 1.4 8 EXTVCC (V) 200 IMON_OUT, IMON_IN (A) BOOST AND BUCK-BOOST REGIONS 6 8705A G12 VIN Supply Current vs Voltage (Not Switching) TJ = 25C 1.6 4 8705A G11 Maximum VC vs SS 1.8 5.5 20 18 8705A G10 2.0 EXTVCC FALLING 6.0 5.0 BOOST REGION -100 EXTVCC RISING INTVCC (V) 6.0 INTVCC (V) -|CSP-CSN| (mV) INTVCC Line Regulation (VIN = 12V) 7.0 -20 -140 TA = 25C unless otherwise specified. 1.30 60 LDO (V) DUTY CYCLE (%) 3.0 40 2.0 20 0 -50 -25 2.5 0 25 50 75 100 125 150 TEMPERATURE (C) 8705A G16 1.5 2.5 125C 25C -40C 3 3.5 4 4.5 5 5.5 6 INTVCC (V) 8705A G17 PIN THRESHOLD VOLTAGE (V) 1.28 80 1.26 1.24 1.22 RISING 1.20 1.18 FALLING 1.16 1.14 1.12 SHDN SWEN 1.10 -55 -35 -15 5 25 45 65 85 105 125 145 TEMPERATURE (C) 8705A G18 8705af 8 For more information www.linear.com/LT8705A LT8705A Typical Performance Characteristics SRVO_xx Pin Activation Thresholds Internal VIN UVLO SHDN and MODE Pin Currents 3.0 16 MODE 14 125 VPIN-VREGULATION VPIN APPROACHING VREGULATION (mV) 18 2.5 SHDN 12 VIN UVLO (V) CURRENT INTO PIN (A) TA = 25C unless otherwise specified. 10 8 6 4 2 2.0 1.5 1.0 0.5 0 -2 0 3 6 9 0 -40 -20 12 15 18 21 24 27 30 PIN VOLTAGE (V) 0 20 40 60 80 TEMPERATURE (C) 75 50 FBIN FBOUT IMON_IN IMON_OUT 25 0 -25 -50 -75 -50 -25 100 120 0 25 50 75 100 125 150 TEMPERATURE (C) 8705A G20 8705A G19 SRVO_xx Pin Activation Threshold Hysteresis PIN ACTIVATION THRESHOLD HYSTERSIS (mV) 100 8705A G21 Forced Continuous Mode (Figure 15) Discontinuous Mode (Figure 15) 50 40 SW1 20V/DIV SW1 50V/DIV 30 20 FBIN FBOUT IMON_IN IMON_OUT 10 0 -50 -25 0 SW2 20V/DIV SW2 50V/DIV IL 2A/DIV IL 2A/DIV 25 50 75 100 125 150 TEMPERATURE (C) VIN = 72V VOUT = 48V 8705A G23 5s/DIV VIN = 36V VOUT = 48V 5s/DIV 8705A G24 8705A G22 Forced Continuous Mode (Figure 14) Forced Continuous Mode (Figure 14) SW1 20V/DIV SW1 50V/DIV SW2 20V/DIV SW2 20V/DIV IL 2A/DIV IL 2A/DIV VIN = 48V VOUT = 48V 5s/DIV 8705A G25 VIN = 72V VOUT = 48V 5s/DIV 8705A G26 8705af For more information www.linear.com/LT8705A 9 LT8705A Typical Performance Characteristics Burst Mode Operation (Figure 14) TA = 25C unless otherwise specified. VOUT 500mV/DIV VOUT 100mV/DIV VOUT 100mV/DIV IL 2A/DIV IL 5A/DIV IL 1A/DIV VIN = 36V VOUT = 48V 2ms/DIV 8705A G27 VIN = 72V VOUT = 48V 8705A G28 5ms/DIV Load Step (Figure 14) VIN = 36V 500s/DIV VOUT = 48V LOAD STEP = 1A TO 3A 8705A G29 Load Step (Figure 14) VOUT 500mV/DIV VOUT 500mV/DIV IL 2A/DIV IL 2A/DIV VIN = 72V 500s/DIV VOUT = 48V LOAD STEP = 1A TO 3A 8705A G30 VIN = 48V 500s/DIV VOUT = 48V LOAD STEP = 1A TO 3A Line Transient (Figure 14) 8705A G31 Line Transient (Figure 14) VIN 36V TO 72V VIN 72V TO 36V VC 0.5V/DIV VC 0.5V/DIV VOUT 0.5V/DIV VOUT 0.5V/DIV IL 2A/DIV IL 2A/DIV 2ms/DIV Load Step (Figure 14) Burst Mode Operation (Figure 14) 8705A G32 2ms/DIV 8705A G33 8705af 10 For more information www.linear.com/LT8705A LT8705A Pin Functions (QFN/TSSOP) SHDN (Pin 1/Pin 4): Shutdown Pin. Tie high to enable device. Ground to shut down and reduce quiescent current to a minimum. Do not float this pin. RT (Pin 12/Pin 15): Timing Resistor Pin. Adjusts the switching frequency. Place a resistor from this pin to ground to set the free-running frequency. Do not float this pin. CSN (Pin 2/Pin 5): The (-) Input to the Inductor Current Sense and Reverse-Current Detect Amplifier. BG1, BG2 (Pins 14, 16/Pins 17, 19): Bottom Gate Drive. Drives the gates of the bottom N-channel MOSFETs between ground and GATEVCC. CSP (Pin 3/Pin 6): The (+) Input to the Inductor Current Sense and Reverse-Current Detect Amplifier. The VC pin voltage and built-in offsets between CSP and CSN pins, in conjunction with the RSENSE resistor value, set the current trip threshold. LDO33 (Pin 4/Pin 7): 3.3V Regulator Output. Bypass this pin to ground with a minimum 0.1F ceramic capacitor. FBIN (Pin 5/Pin 8): Input Feedback Pin. This pin is connected to the input error amplifier input. FBOUT (Pin 6/Pin 9): Output Feedback Pin. This pin connects the error amplifier input to an external resistor divider from the output. IMON_OUT (Pin 7/Pin 10): Output Current Monitor Pin. The current out of this pin is proportional to the output current. See the Operation and Applications Information sections. VC (Pin 8/Pin 11): Error Amplifier Output Pin. Tie external compensation network to this pin. SS (Pin 9/Pin 12): Soft-Start Pin. Place at least 100nF of capacitance here. Upon start-up, this pin will be charged by an internal resistor to 2.5V. CLKOUT (Pin 10/Pin 13): Clock Output Pin. Use this pin to synchronize one or more compatible switching regulator ICs to the LT8705A. CLKOUT toggles at the same frequency as the internal oscillator or as the SYNC pin, but is approximately 180 out of phase. CLKOUT may also be used as a temperature monitor since the CLKOUT duty cycle varies linearly with the part's junction temperature. The CLKOUT pin can drive capacitive loads up to 200pF. SYNC (Pin 11/Pin 14): To synchronize the switching frequency to an outside clock, simply drive this pin with a clock. The high voltage level of the clock needs to exceed 1.3V, and the low level should be less than 0.5V. Drive this pin to less than 0.5V to revert to the internal free-running clock. See the Applications Information section for more information. GATEVCC (Pin 15/Pin 18): Power Supply for Gate Drivers. Must be connected to the INTVCC pin. Do not power from any other supply. Locally bypass to GND. BOOST1, BOOST2 (Pins 23, 17/Pins 28, 20): Boosted Floating Driver Supply. The (+) terminal of the bootstrap capacitor connects here. The BOOST1 pin swings from a diode voltage below GATEVCC up to VIN + GATEVCC. The BOOST2 pin swings from a diode voltage below GATEVCC up to VOUT + GATEVCC TG1, TG2 (Pins 22, 18/Pins 26, 21): Top Gate Drive. Drives the top N-channel MOSFETs with voltage swings equal to GATEVCC superimposed on the switch node voltages. SW1, SW2 (Pins 21, 19/Pins 24, 22): Switch Nodes. The (-) terminals of the bootstrap capacitors connect here. SRVO_FBIN (Pin 25 QFN Only): Open-Drain Logic Output. This pin is pulled to ground when the input voltage feedback loop is active. SRVO_IIN (Pin 26 QFN Only): Open-Drain Logic Output. The pin is pulled to ground when the input current loop is active. SRVO_IOUT (Pin 27 QFN Only): Open-Drain Logic Output. The pin is pulled to ground when the output current feedback loop is active. SRVO_FBOUT (Pin 28 QFN Only): Open-Drain Logic Output. This pin is pulled to ground when the output voltage feedback loop is active. EXTVCC (Pin 29/Pin 30): External VCC Input. When EXTVCC exceeds 6.4V (typical), INTVCC will be powered from this pin. When EXTVCC is lower than 6.22V (typical), INTVCC will be powered from VIN. CSNOUT (Pin 30/Pin 32): The (-) Input to the Output Current Monitor Amplifier. Connect this pin to VOUT when not in use. See Applications Information section for proper use of this pin. 8705af For more information www.linear.com/LT8705A 11 LT8705A Pin Functions (QFN/TSSOP) CSPOUT (Pin 31/Pin 34): The (+) Input to the Output Current Monitor Amplifier. This pin and the CSNOUT pin measure the voltage across the sense resistor, RSENSE2, to provide the output current signals. Connect this pin to VOUT when not in use. See Applications Information section for proper use of this pin. CSNIN (Pin 32/Pin 36): The (-) Input to the Input Current Monitor Amplifier. This pin and the CSPIN pin measure the voltage across the sense resistor, RSENSE1, to provide the input current signals. Connect this pin to VIN when not in use. See Applications Information section for proper use of this pin. CSPIN (Pin 33/Pin 37): The (+) Input to the Input Current Monitor Amplifier. Connect this pin to VIN when not in use. See Applications Information section for proper use of this pin. SWEN (Pin 36 QFN Only): Switch Enable Pin. Tie high to enable switching. Ground to disable switching. Don't float this pin. This pin is internally tied to INTVCC in the TSSOP package. IMON_IN (Pin 38/Pin 3): Input Current Monitor Pin. The current out of this pin is proportional to the input current. See the Operation and Applications Information sections. MODE (Pin 37/Pin 2): Mode Pin. The voltage applied to this pin sets the operating mode of the controller. When the applied voltage is less than 0.4V, the forced continuous current mode is active. When this pin is allowed to float, Burst Mode operation is active. When the MODE pin voltage is higher than 2.3V, discontinuous mode is active. GND (Pin 13, Exposed Pad Pin 39/Pin 16, Exposed Pad Pin 39): Ground. Tie directly to local ground plane. VIN (Pin 34/Pin 38): Main Input Supply Pin. It must be locally bypassed to ground. INTVCC (Pin 35/Pin 1): Internal 6.35V Regulator Output. Must be connected to the GATEVCC pin. INTVCC is powered from EXTVCC when the EXTVCC voltage is higher than 6.4V, otherwise INTVCC is powered from VIN . Bypass this pin to ground with a minimum 4.7F ceramic capacitor. 8705af 12 For more information www.linear.com/LT8705A LT8705A Block Diagram VIN RSENSE1 RSENSE CSN SWEN CSP DB1 BOOST1 CSNIN - CSPIN + + + A7 M1 SW1 - A5 CB1 TG1 A8 M2 BUCK LOGIC - D1 (OPT) GATEVCC VIN BG1 IMON_IN GND MODE BOOST CAPACITOR CHARGE CONTROL BG2 CLKOUT SYNC OSC RT M3 SW2 BOOST LOGIC TG2 + CB2 BOOST2 A9 - DB2 2.5V OT OI_IN OI_OUT STARTUP AND FAULT LOGIC SS + CSPOUT - CSNOUT A6 FAULT_INT RSENSE2 VOUT IMON_OUT - UV_INTVCC M4 D2 (OPT) EA1 + UV_LDO33 RSHDN1 UV_VIN UV_GATEVCC 1.208V + SHDN EA2 + - RSHDN2 VIN IMON_IN - 1.234V + EXTVCC - 6.35V LDO REG EA3 + 6.4V EN FBIN EN 6.35V LDO REG 3.3V LDO REG LDO REG VIN INTVCC 1.205V + 1.207V - INTERNAL SUPPLY1 LDO33 RFBIN2 - EA4 INTERNAL SUPPLY2 FBOUT VC SRVO_IOUT SRVO_IIN SRVO_FBIN RFBIN1 RFBOUT1 RFBOUT2 SRVO_FBOUT 8705A F01 Figure 1. Block Diagram 8705af For more information www.linear.com/LT8705A 13 LT8705A Operation Refer to the Block Diagram (Figure 1) when reading the following sections about the operation of the LT8705A. Main Control Loop The LT8705A is a current mode controller that provides an output voltage above, equal to or below the input voltage. The LTC(R) proprietary topology and control architecture employs a current-sensing resistor (RSENSE) in buck or boost modes. The inductor current is controlled by the voltage on the VC pin, which is the diode-AND of error amplifiers EA1-EA4. In the simplest form, where the output is regulated to a constant voltage, the FBOUT pin receives the output voltage feedback signal, which is compared to the internal reference voltage by EA4. Low output voltages would create a higher VC voltage, and thus more current would flow into the output. Conversely, higher output voltages would cause VC to drop, thus reducing the current fed into the output. The LT8705A contains four error amplifiers (EA1-EA4) allowing it to regulate or limit the output current (EA1), input current (EA2), input voltage (EA3) and/or output voltage (EA4). In a typical application, the output voltage might be regulated using EA4, while the remaining error amplifiers are monitoring for excessive input or output current or an input undervoltage condition. In other applications, such as a battery charger, the output current regulator (EA1) can facilitate constant current charging until a predetermined voltage is reached where the output voltage (EA4) control would take over. INTVCC/EXTVCC/GATEVCC/LDO33 Power Power for the top and bottom MOSFET drivers, the LDO33 pin and most internal circuitry is derived from the INTVCC pin. INTVCC is regulated to 6.35V (typical) from either the VIN or EXTVCC pin. When the EXTVCC pin is left open or tied to a voltage less than 6.22V (typical), an internal low dropout regulator regulates INTVCC from VIN. If EXTVCC is taken above 6.4V (typical), another low dropout regulator will instead regulate INTVCC from EXTVCC. Regulating INTVCC from EXTVCC allows the power to be derived from the lowest supply voltage (highest efficiency) such as the LT8705A switching regulator output (see INTVCC Regulators and EXTVCC Connection in the Applications Information section for more details). 14 The GATEVCC pin directly powers the bottom MOSFET drivers for switches M2 and M3. GATEVCC should always be connected to INTVCC and should not be powered or connected to any other source. Undervoltage lock outs (UVLOs) monitoring INTVCC and GATEVCC disable the switching regulator when the pins are below 4.65V (typical). The LDO33 pin is available to provide power to external components such as a microcontroller and/or to provide an accurate bias voltage. Load current is limited to 17.25mA (typical). As long as SHDN is high the LDO33 output is linearly regulated from the INTVCC pin and is not affected by the INTVCC or GATEVCC UVLOs or the SWEN pin voltage. LDO33 will remain regulated as long as SHDN is high and sufficient voltage is available on INTVCC (typically > 4.0V). An undervoltage lockout, monitoring LDO33, will disable the switching regulator when LDO33 is below 3.04V (typical). Start-Up Figure 2 illustrates the start-up sequence for the LT8705A. The master shutdown pin for the chip is SHDN. When driven below 0.35V (LT8705AE, LT8705AI) or 0.3V (LT8705AH, LT8705AMP) the chip is disabled (chip off state) and quiescent current is minimal. Increasing the SHDN voltage can increase quiescent current but will not enable the chip until SHDN is driven above 1.234V (typical) after which the INTVCC and LDO33 regulators are enabled (switcher off state). External devices powered by the LDO33 pin can become active at this time if enough voltage is available on VIN or EXTVCC to raise INTVCC, and thus LDO33, to an adequate voltage. Starting up the switching regulator happens after SWEN (switcher enable) is also driven above 1.206V (typical), INTVCC and GATEVCC have risen above 4.81V (typical) and the LDO33 pin has risen above 3.08V (typical) (initialize state). The SWEN pin is not available in the TSSOP package. In this package the SWEN pin is internally connected to INTVCC. Start-Up: Soft-Start of Switch Current In the initialize state, the SS (soft-start) pin is pulled low to prepare for soft starting the regulator. If forced continuous mode is selected (MODE pin low), the part is put into discontinuous mode during soft-start to prevent current For more information www.linear.com/LT8705A 8705af LT8705A Operation SHDN < 1.184V OR VIN < 2.5V OR TJUNCTION > 165C CHIP OFF * SWITCHER OFF * LDOs OFF TYPICAL VALUES TJUNCTION < 160C AND SHDN > 1.234V AND VIN > 2.5V AND (SWEN* < 1.184V OR (INTVCC AND GATEVCC < 4.65V) OR LDO33 < 3.04V) TYPICAL VALUES SWITCHER OFF * SWITCHER DISABLED * INTVCC AND LDO33 OUTPUTS ENABLED SHDN > 1.234V AND VIN > 2.5V AND SWEN* > 1.206V AND (INTVCC AND GATEVCC > 4.81V) AND LDO33 > 3.075V TYPICAL VALUES INITIALIZE * SS PULLED LOW * FORCE DISCONTINOUS MODE UNLESS Burst Mode OPERATION SELECTED FAULT SS < 50mV SOFT-START * SS CHARGES UP * SWITCHER ENABLED FAULT DETECTED FAULT * SS CHARGES UP * SWITCHER DISABLED * CLKOUT DISABLED SS > 1.6V AND NO FAULT CONDITIONS STILL DETECTED NORMAL MODE * NORMAL OPERATION * WHEN SS > 1.6V ... * CLKOUT ENABLED * ENABLE FORCED CONTINUOUS MODE IF SELECTED FAULT FAULT POST FAULT DELAY * SS SLOWLY DISCHARGES SS < 50mV *SWEN IS CONNECTED TO INTVCC IN THE TSSOP PACKAGE FAULT = OVERVOLTAGE (IMON_IN OR IMON_OUT > 1.61V TYP) 8705A F02 Figure 2. Start-Up and Fault Sequence from being drawn out of the output and forced into the input. After SS has been discharged to less than 50mV, a soft-start of the switching regulator begins (soft-start state). The soft-start circuitry provides for a gradual ramp-up of the inductor current by gradually allowing the VC voltage to rise (refer to VC vs SS Voltage in the Typical Performance Characteristics). This prevents abrupt surges of current from being drawn out of the input power supply. An integrated 100k resistor pulls the SS pin to 2.5V. The ramp rate of the SS pin voltage is set by this 100k resistor and the external capacitor connected to this pin. Once SS gets to 1.6V, the CLKOUT pin is enabled, the part is allowed to enter forced continuous mode (if MODE is low) and an internal regulator pulls SS up quickly to 2.5V. Typical values for the external soft-start capacitor range from 100nF to 1F. A minimum of 100nF is recommended. Fault Conditions The LT8705A activates a fault sequence under certain operating conditions. If any of these conditions occur (see Figure 2) the CLKOUT pin and internal switching activity are disabled. At the same time, a timeout sequence commences where the SS pin is charged up to a minimum of 1.6V (fault detected state). The SS pin will continue 8705af For more information www.linear.com/LT8705A 15 LT8705A Operation charging up to 2.5V and be held there in the case of a fault event that persists. After the fault condition had ended and SS is greater than 1.6V, SS will then slowly discharge to 50mV (post fault delay state). This timeout period relieves the part and other downstream power components from electrical and thermal stress for a minimum amount of time as set by the voltage ramp rate on the SS pin. After SS has discharged to < 50mV, the LT8705A will enter the soft-start state and restart switching activity. is turned on first. Inductor current is sensed by amplifier A5 while switch M2 is on. A slope compensation ramp is added to the sensed voltage which is then compared by A8 to a reference that is proportional to VC. After the sensed inductor current falls below the reference, switch M2 is turned off and switch M1 is turned on for the remainder of the cycle. Switches M1 and M2 will alternate, behaving like a typical synchronous buck regulator. CLOCK Power Switch Control Figure 3 shows a simplified diagram of how the four power switches are connected to the inductor, VIN, VOUT and ground. Figure 4 shows the regions of operation for the LT8705A as a function of VOUT -VIN or switch duty cycle DC. The power switches are properly controlled so the transfer between modes is continuous. VIN TG1 M1 L M4 TG2 SW2 M2 M3 BG2 RSENSE 8705A F03 Figure 3. Simplified Diagram of the Output Switches SWITCH M3 DCMAX VOUT -VIN BOOST REGION 0 BUCK/BOOST REGION BUCK REGION M1 ON, M2 OFF PWM M3, M4 SWITCHES SWITCH M3 DCMIN SWITCH M2 DCMIN 4-SWITCH PWM M4 ON, M3 OFF PWM M1, M2 SWITCHES 8705A F04 SWITCH M2 DCMAX Figure 4. Operating Regions vs VOUT-VIN Power Switch Control: Buck Region (VIN >> VOUT) When VIN is significantly higher than VOUT, the part will run in the buck region. In this region switch M3 is always off. Also, switch M4 is always on unless reverse current is detected while in Burst Mode operation or discontinuous mode. At the start of every cycle, synchronous switch M2 16 SWITCH M2 OFF SWITCH M3 ON SWITCH M4 IL 8705A F05 Figure 5. Buck Region (VIN >> VOUT) VOUT SW1 BG1 SWITCH M1 The part will continue operating in the buck region over a range of switch M2 duty cycles. The duty cycle of switch M2 in the buck region is given by: V DC(M2,BUCK) = 1- OUT *100% VIN As VIN and VOUT get closer to each other, the duty cycle decreases until the minimum duty cycle of the converter in buck mode reaches DC(ABSMIN,M2,BUCK). If the duty cycle becomes lower than DC(ABSMIN,M2,BUCK) the part will move to the buck-boost region. DC(ABSMIN,M2,BUCK) tON(M2,MIN) * f * 100% where: tON(M2,MIN) is the minimum on-time for the synchronous switch in buck operation (260ns typical, see Electrical Characteristics). f is the switching frequency When VIN is much higher than VOUT the duty cycle of switch M2 will increase, causing the M2 switch off-time to decrease. The M2 switch off-time should be kept above 245ns (typical, see Electrical Characteristics) to maintain steady-state operation, avoid duty cycle jitter, increased output ripple and reduction in maximum output current. For more information www.linear.com/LT8705A 8705af LT8705A Operation Power Switch Control: Buck-Boost (VIN VOUT) Power Switch Control: Boost Region (VIN << VOUT) When VIN is close to VOUT, the controller enters the buckboost region. Figure 6 shows typical waveforms in this region. Every cycle, if the controller starts with switches M2 and M4 turned on, the controller first operates as if in the buck region. When A8 trips, switch M2 is turned off and M1 is turned on until the middle of the clock cycle. Next, switch M4 turns off and M3 turns on. The LT8705A then operates as if in boost mode until A9 trips. Finally switch M3 turns off and M4 turns on until the end of the cycle. When VOUT is significantly higher than VIN, the part will run in the boost region. In this region switch M1 is always on and switch M2 is always off. At the start of every cycle, switch M3 is turned on first. Inductor current is sensed by amplifier A5 while switch M3 is on. A slope compensation ramp is added to the sensed voltage which is then compared (A9) to a reference that is proportional to VC. After the sensed inductor current rises above the reference voltage, switch M3 is turned off and switch M4 is turned on for the remainder of the cycle. Switches M3 and M4 will alternate, behaving like a typical synchronous boost regulator. If the controller starts with switches M1 and M3 turned on, the controller first operates as if in the boost region. When A9 trips, switch M3 is turned off and M4 is turned on until the middle of the clock cycle. Next, switch M1 turns off and M2 turns on. The LT8705A then operates as if in buck mode until A8 trips. Finally switch M2 turns off and M1 turns on until the end of the cycle. CLOCK SWITCH M1 The part will continue operating in the boost region over a range of switch M3 duty cycles. The duty cycle of switch M3 in the boost region is given by: V DC(M3,BOOST) = 1- IN *100% VOUT As VIN and VOUT get closer to each other, the duty cycle decreases until the minimum duty cycle of the converter in boost mode reaches DC(ABSMIN,M3,BOOST). If the duty cycle becomes lower than DC(ABSMIN,M3,BOOST) the part will move to the buck-boost region: SWITCH M2 SWITCH M3 SWITCH M4 IL 8705A F06a (6a) Buck-Boost Region (VIN VOUT) DC(ABSMIN,M3,BOOST) tON(M3,MIN) * f * 100% where: tON(M3,MIN) is the minimum on-time for the main switch in boost operation (265ns typical, see Electrical Characteristics) CLOCK SWITCH M1 f is the switching frequency SWITCH M2 SWITCH M3 CLOCK SWITCH M4 ON SWITCH M1 IL 8705A F06b OFF SWITCH M2 (6b) Buck-Boost Region (VIN VOUT) SWITCH M3 Figure 6. Buck-Boost Region SWITCH M4 IL 8705A F07 Figure 7. Boost Region (VIN << VOUT) 8705af For more information www.linear.com/LT8705A 17 LT8705A Operation When VOUT is much higher than VIN the duty cycle of switch M3 will increase, causing the M3 switch off-time to decrease. The M3 switch off-time should be kept above 245ns (typical, see Electrical Characteristics) to maintain steady-state operation, avoid duty cycle jitter, increased output ripple and reduction in maximum output current. Light Load Current Operation (MODE Pin) Under light current load conditions, the LT8705A can be set to operate in discontinuous mode, forced continuous mode, or Burst Mode operation. To select forced continuous mode, tie the MODE pin to a voltage below 0.4V (i.e., ground). To select discontinuous mode, tie MODE to a voltage above 2.3V (i.e., LDO33). To select Burst Mode operation, float the MODE pin or tie it between 1.0V and 1.7V. Discontinuous Mode: When the LT8705A is in discontinuous mode, synchronous switch M4 is held off whenever reverse current in the inductor is detected. This is to prevent current draw from the output and/or feeding current to the input supply. Under very light loads, the current comparator may also remain tripped for several cycles and force switches M1 and M3 to stay off for the same number of cycles (i.e., skipping pulses). Synchronous switch M2 will remain on during the skipped cycles, but since switch M4 is off, the inductor current will not reverse. Burst Mode Operation: Burst Mode operation sets a VC level, with about 25mV of hysteresis, below which switching activity is inhibited and above which switching activity is re-enabled. A typical example is when, at light output currents, VOUT rises and forces the VC pin below the threshold that temporarily inhibits switching. After VOUT drops slightly and VC rises ~25mV the switching is resumed, initially in the buck-boost region. Burst Mode operation can increase efficiency at light load currents by eliminating unnecessary switching activity and related power losses. Burst Mode operation handles reverse-current detection similar to discontinuous mode. The M4 switch is turned off when reverse current is detected. Forced Continuous Mode: The forced continuous mode allows the inductor current to reverse directions without any switches being forced "off" to prevent this from hap- pening. At very light load currents the inductor current will swing positive and negative as the appropriate average current is delivered to the output. During soft-start, when the SS pin is below 1.6V, the part will be forced into discontinuous mode to prevent pulling current from the output to the input. After SS rises above 1.6V, forced continuous mode will be enabled. Voltage Regulation Loops The LT8705A provides two constant-voltage regulation loops, one for output voltage and one for input voltage. A resistor divider between VOUT, FBOUT and GND senses the output voltage. As with traditional voltage regulators, when FBOUT rises near or above the reference voltage of EA4 (1.207V typical, see Block Diagram), the VC voltage is reduced to command the amount of current that keeps VOUT regulated to the desired voltage. The input voltage can also be sensed by connecting a resistor divider between VIN, FBIN and GND. When the FBIN voltage falls near or below the reference voltage of EA3 (1.205V typical, see Block Diagram), the VC voltage is reduced to also reduce the input current. For applications with a high input source impedance (i.e., a solar panel), the input voltage regulation loop can prevent the input voltage from becoming too low under high output load conditions. For applications with a lower input source impedance (i.e., batteries and voltage supplies), the FBIN pin can be used to stop switching activity when the input power supply voltage gets too low for proper system operation. See the Applications Information section for more information about setting up the voltage regulation loops. Current Monitoring and Regulation The LT8705A provides two constant-current regulation loops, one for input current and one for output current. A sensing resistor close to the input capacitor, sensed by CSPIN and CSNIN, monitors the input current. A current, linearly proportional to the sense voltage (VCSPIN-VCSNIN), is forced out of the IMON_IN pin and into an external resistor. The resulting voltage VIMON_IN is therefore linearly proportional to the input current. Similarly, a sensing resistor close to the output capacitor, and sensed by 8705af 18 For more information www.linear.com/LT8705A LT8705A Operation When the input or output current causes the respective IMON_IN or IMON_OUT voltage to rise near or above 1.208V (typical), the VC pin voltage will be pulled down to maintain the desired maximum input and/or output current (see EA1 and EA2 on the Block Diagram). The input current limit function prevents overloading the DC input source, while the output current limit provides a building block for battery charger or LED driver applications. It can also serve as short-circuit protection for a constant-voltage regulator. See the Applications Information section for more information about setting up the current regulation loops. greater than their regulation voltages (1.2V typical). SRVO_FBIN is pulled low when FBIN is near or lower than its regulation voltage (1.2V typical). The SRVO pins can therefore be used as indicators of when their respective feedback loops are active. For example, the SRVO_FBOUT pin pulls low when FBOUT rises to within 29mV (typical, see Electrical Characteristics) of its regulation voltage (1.207V typical). The pull-down turns off after FBOUT falls to more than 44mV (typical) lower than its regulation voltage. As another example, the SRVO_IOUT pin can be read to determine when the output current has nearly reached its predetermined limit. A logic "1" on SRVO_IOUT indicates that the output current has not reached the current limit and a logic "0" indicates that it has. SRVO Pins CLKOUT and Temperature Sensing CSPOUT and CSNOUT will monitor the output current and generate a voltage VIMON_OUT that is linearly proportional to the output current. The QFN package has four open-drain SRVO pins: SRVO_FBIN, SRVO_FBOUT, SRVO_IIN, SRVO_IOUT. Place pull-up resistors from the desired SRVO pin(s) to a power supply less than 30V (i.e., the LDO33 pin) to enable reading of their logic states. The SRVO_FBOUT, SRVO_IIN and SRVO_IOUT pins are pulled low when their associated error amp (EA4, EA2, EA1) input voltages are near or The CLKOUT pin toggles at the LT8705A's internal clock frequency whether the internal clock is synchronized to an external source or is free-running based on the external RT resistor. The CLKOUT pin can be used to synchronize other devices to the LT8705A's switching frequency. Also, the duty cycle of CLKOUT is proportional to the die temperature and can be used to monitor the die for thermal issues. 8705af For more information www.linear.com/LT8705A 19 LT8705A Applications Information The first page shows a typical LT8705A application circuit. After the switching frequency is selected, external component selection continues with the selection of RSENSE and the inductor value. Next, the power MOSFETs are selected. Finally, CIN and COUT are selected. The following examples and equations assume continuous conduction mode unless otherwise specified. The circuit can be configured for operation up to an input and/or output voltage of 80V. LT8705 L = 6.2H VIN = 17V, VOUT = 25V MODE = 0V SS RISES > 1.6V DCM TO FCM TRANSITION OCCURS O IL 10A/DIV UNDERSHOOT LT8705A vs LT8705 The LT8705A is a pin for pin compatible, minor silicon revision of the LT8705. The LT8705A contains a few main improvements over the LT8705. The first main improvement effects the transition from DCM (discontinuous conduction mode) to FCM (forced continuous mode) operation. The most common transition from DCM to FCM occurs during soft-start while the MODE pin is driven low, thus selecting FCM operation. As illustrated in the startup sequence of Figure 2, the LT8705 and LT8705A begin operating in DCM, even if MODE is set to FCM. When the SS pin rises above 1.6V the LT8705 and LT8705A transition from DCM to FCM. The improved LT8705A reduces or eliminates the inductor current (IL) undershoot that could occur during the following operating conditions... * The operating MODE transitions from DCM to FCM and * VC is low enough to command a negative inductor current (IL) and * VOUT is near or greater than VIN at the time of the transition Figure 8 shows examples of the inductor current undershoot that has been reduced with the LT8705A (Figure 8b) as compared to the LT8705 (Figure 8a). Note that most LT8705 applications will not exhibit nearly as much undershoot as shown in Figure 8a. Conditions that reduce the amount of undershoot are... * Higher inductance * Higher frequency * Higher VC during the DCM to FCM transition * Lower VIN during the DCM to FCM transition 10s/DIV (8a) LT8705A L = 6.2H VIN = 17V, VOUT = 25V MODE = 0V SS RISES > 1.6V DCM TO FCM TRANSITION OCCURS O IL 10A/DIV 10s/DIV 8705A F08b (8b) Figure 8. LT8705 and LT8705A Inductor Current During DCM to FCM Transition The operating conditions for Figures 8a and 8b were intentionally set to maximize undershoot, including having VC at the lowest possible voltage at the time of the transition. The second main improvement effects the IMON_IN and IMON_OUT currents, typically when operating below -25C, when the respective VCSPIN - VCSNIN or VCSPOUT - VCSNOUT voltages are very close to 0mV. Using the LT8705 under these conditions, the IMON_OUT or IMON_IN output current can increase, above the expected amount, by a few A. The increased current, above the expected amount, diminishes as VCSPIN - VCSNIN or VCSPOUT - VCSNOUT increases and is typically gone when VCSPIN - VCSNIN or VCSPOUT - VCSNOUT becomes 5mV or greater. The LT8705A has been improved to eliminate the additional output current under those conditions. * Lower VOUT - VIN during the DCM to FCM transition 20 8705A F08a For more information www.linear.com/LT8705A 8705af LT8705A Applications Information Operating Frequency Selection The LT8705A uses a constant frequency architecture between 100kHz and 400kHz. The frequency can be set using the internal oscillator or can be synchronized to an external clock source. Selection of the switching frequency is a trade-off between efficiency and component size. Low frequency operation increases efficiency by reducing MOSFET switching losses, but requires more inductance and/or capacitance to maintain low output ripple voltage. For high power applications, consider operating at lower frequencies to minimize MOSFET heating from switching losses. The switching frequency can be set by placing an appropriate resistor from the RT pin to ground and tying the SYNC pin low. The frequency can also be synchronized to an external clock source driven into the SYNC pin. The following sections provide more details. Internal Oscillator The operating frequency of the LT8705A can be set using the internal free-running oscillator. When the SYNC pin is driven low (<0.5V), the frequency of operation is set by the value of a resistor from the RT pin to ground. An internally trimmed timing capacitor resides inside the IC. The oscillator frequency is calculated using the following formula: 43,750 fOSC = kHz R T +1 where fOSC is in kHz and RT is in k. Conversely, RT (in k) can be calculated from the desired frequency (in kHz) using: 43,750 RT = - 1k fOSC SYNC Pin and Clock Synchronization The operating frequency of the LT8705A can be synchronized to an external clock source. To synchronize to the external source, simply provide a digital clock signal into the SYNC pin. The LT8705A will operate at the SYNC clock frequency. The duty cycle of the SYNC signal must be between 20% and 80% for proper operation. Also, the frequency of the SYNC signal must meet the following two criteria: 1. SYNC may not toggle outside the frequency range of 100kHz to 400kHz unless it is stopped low to enable the free-running oscillator. 2. The SYNC pin frequency can always be higher than the free-running oscillator set frequency, fOSC, but should not be less than 25% below fOSC. After SYNC begins toggling, it is recommended that switching activity is stopped before the SYNC pin stops toggling. Excess inductor current can result when SYNC stops toggling as the LT8705A transitions from the external SYNC clock source to the internal free-running oscillator clock. Switching activity can be stopped by driving either the SWEN or SHDN pin low. CLKOUT Pin and Clock Synchronization The CLKOUT pin can drive up to 200pF and toggles at the LT8705A's internal clock frequency whether the internal clock is synchronized to the SYNC pin or is free-running based on the external RT resistor. The rising edge of CLKOUT is approximately 180 out of phase from the internal clock's rising edge or the SYNC pin's rising edge if it is toggling. CLKOUT toggles only in normal mode (see Figure 2). The CLKOUT pin can be used to synchronize other devices to the LT8705A's switching frequency. For example, the CLKOUT pin can be tied to the SYNC pin of another LT8705A regulator which will operate approximately 180 out of phase of the master LT8705A due to the CLKOUT phase shift. The frequency of the master LT8705A can be set by the external RT resistor or by toggling the SYNC pin. CLKOUT will begin oscillating after the master LT8705A enters normal mode (see Figure 2). Note that the RT pin of the slave LT8705A must have a resistor tied to ground. In general, use the same value RT resistor for all of the synchronized LT8705As. 8705af For more information www.linear.com/LT8705A 21 LT8705A Applications Information The duty cycle of CLKOUT is proportional to the die temperature and can be used to monitor the die for thermal issues. See the Junction Temperature Measurement section for more information. Inductor Current Sensing and Slope Compensation The LT8705A operates using inductor current mode control. As described previously in the Power Switch Control section, the LT8705A measures the peak of the inductor current waveform in the boost region and the valley of the inductor current waveform in the buck region. The inductor current is sensed across the RSENSE resistor with pins CSP and CSN. During any given cycle, the peak (boost region) or valley (buck region) of the inductor current is controlled by the VC pin voltage. Slope compensation provides stability in constantfrequency current mode control architectures by preventing subharmonic oscillations at high duty cycles. This is accomplished internally by adding a compensating ramp to the inductor current signal in the boost region, or subtracting a ramp from the inductor current signal in the buck region. At higher duty cycles, this results in a reduction of maximum inductor current in the boost region, and an increase of the maximum inductor current in the buck region. For example, refer to the Maximum Inductor Current Sense Voltage vs Duty Cycle graph in the Typical Performance Characteristics section. The graph shows that, with VC at its maximum voltage, the maximum inductor sense voltage VRSENSE is between 78mV and 117mV depending on the duty cycle. It also shows that the maximum inductor valley current in the buck region is 86mV increasing to ~130mV at higher duty cycles. RSENSE Selection and Maximum Current Start by finding the boost region duty cycle when VIN is minimum and VOUT is maximum using: VIN(MIN) *100% DC(MAX,M3,BOOST) 1- VOUT(MAX) For example, an application with a VIN range of 12V to 48V and VOUT set to 36V will have: 12V DC(MAX,M3,BOOST) 1- *100% = 67% 36V Referring to the Maximum Inductor Current Sense Voltage graph in the Typical Performance Characteristics section, the maximum RSENSE voltage at 67% duty cycle is 93mV, or: VRSENSE(MAX,BOOST, MAX) 93mV for VIN = 12V, VOUT = 36V. Next, the inductor ripple current in the boost region must be determined. If the main inductor L is not known, the maximum ripple current IL(MAX,BOOST) can be estimated by choosing IL(MAX,BOOST) to be 30% to 50% of the maximum inductor current in the boost region as follows: IL(MAX,BOOST) VOUT(MAX) *IOUT(MAX,BOOST) A 100% VIN(MIN) * - 0.5 %Ripple where: The RSENSE resistance must be chosen properly to achieve the desired amount of output current. Too much resistance can limit the output current below the application requirements. Start by determining the maximum allowed RSENSE resistance in the boost region, RSENSE(MAX,BOOST). Follow this by finding the maximum allowed RSENSE resistance in the buck region, RSENSE(MAX,BUCK). The selected RSENSE resistance must be smaller than both. 22 Boost Region: In the boost region, the maximum output current capability is the least when VIN is at its minimum and VOUT is at its maximum. Therefore RSENSE must be chosen to meet the output current requirements under these conditions. IOUT(MAX,BOOST) is the maximum output load current required in the boost region %Ripple is 30% to 50% For example, using VOUT(MAX) = 36V, VIN(MIN) = 12V, IOUT(MAX,BOOST) = 2A and %Ripple = 40% we can estimate: IL(MAX,BOOST) For more information www.linear.com/LT8705A 36V * 2A = 3A 100% 12V * - 0.5 40% 8705af LT8705A Applications Information Otherwise, if the inductor value is already known then IL(MAX,BOOST) can be more accurately calculated as follows: DC(MAX,M3,BOOST) * VIN(MIN) 100% IL(MAX,BOOST) = A f *L DC(MAX,M3,BOOST) is the maximum duty cycle percentage in the boost region as calculated previously. f is the switching frequency L is the inductance of the main inductor After the maximum ripple current is known, the maximum allowed RSENSE in the boost region can be calculated as follows: RSENSE(MAX,BOOST) = (2 *IOUT(MAX,BOOST) * VOUT(MIN) ) + (IL(MAX,BOOST) * VIN(MIN) ) where VRSENSE(MAX,BOOST,MAX) is the maximum inductor current sense voltage as discussed in the previous section. Using values from the previous examples: RSENSE(MAX,BOOST) = IL(MIN,BUCK) IOUT(MAX,BUCK) A 100% - 0.5 10% where: where: 2 * VRSENSE(MAX,BOOST,MAX) * VIN(MIN) to be 10% of the maximum inductor current in the buck region as follows: 2 * 93mV *12 = 12.4m (2 * 2A * 36V ) + (3A *12V ) Buck Region: In the buck region, the maximum output current capability is the least when operating at the minimum duty cycle. This is because the slope compensation ramp increases the maximum RSENSE voltage with increasing duty cycle. The minimum duty cycle for buck operation can be calculated using: DC(MIN,M2,BUCK) tON(M2,MIN) * f * 100% where tON(M2,MIN) is 260ns (typical value, see Electrical Characteristics) Before calculating the maximum RSENSE resistance, however, the inductor ripple current must be determined. If the main inductor L is not known, the ripple current IL(MIN,BUCK) can be estimated by choosing IL(MIN,BUCK) IOUT(MAX,BUCK) is the maximum output load current required in the buck region. If the inductor value is already known then IL(MIN,BUCK) can be calculated as follows: DC(MIN,M2,BUCK) * VOUT(MIN) 100% IL (MIN,BUCK ) = A f *L where: DC(MIN,M2,BUCK) is the minimum duty cycle percentage in the buck region as calculated previously. f is the switching frequency L is the inductance of the main inductor After the inductor ripple current is known, the maximum allowed RSENSE in the buck region can be calculated as follows: RSENSE(MAX,BUCK) = ( 2 * 86mV 2 *IOUT(MAX,BUCK) - IL(MIN,BUCK) ) Final RSENSE Value: The final RSENSE value should be lower than both RSENSE(MAX,BOOST) and RSENSE(MAX,BUCK). A margin of 30% or more is recommended. Figure 9 shows approximately how the maximum output current and maximum inductor current would vary with VIN/VOUT while all other operating parameters remain constant (frequency = 350kHz, inductance = 10H, RSENSE = 10m). This graph is normalized and accounts for changes in maximum current due to the slope compensation ramps and the effects of changing ripple current. The curve is theoretical, but can be used as a guide to predict relative changes in maximum output and inductor current over a range of VIN/VOUT voltages. 8705af For more information www.linear.com/LT8705A 23 LT8705A Applications Information the maximum average current that can be provided to the load (IOUT) while operating in the boost region. 1.0 NORMALIZED CURRENT 0.8 0.6 MAXIMUM INDUCTOR CURRENT 0.4 In order to provide adequate load current at low VIN voltages in the boost region, L should be at least: MAXIMUM OUTPUT CURRENT L(MIN1,BOOST) 0.2 0 0.1 1 VIN/VOUT (V/V) 10 8705A F09 Figure 9. Currents vs VIN/VOUT Ratio Reverse Current Limit When the forced continuous mode is selected (MODE pin low), inductor current is allowed to reverse directions and flow from the VOUT side to the VIN side. This can lead to current sinking from the output and being forced into the input. The reverse current is at a maximum magnitude when VC is lowest. The graph of Minimum Inductor Current Sense Voltage in FCM in the Typical Performance Characteristics section can help to determine the maximum reverse current capability. Inductor Selection For high efficiency, choose an inductor with low core loss, such as ferrite. Also, the inductor should have low DC resistance to reduce the I2R losses, and must be able to handle the peak inductor current without saturating. To minimize radiated noise, use a toroid, pot core or shielded bobbin inductor. The operating frequency and inductor selection are interrelated in that higher operating frequencies allow the use of smaller inductor and capacitor values. The following sections discuss several criteria to consider when choosing an inductor value. For optimal performance, choose an inductor that meets all of the following criteria. Inductor Selection: Adequate Load Current in the Boost Region Small value inductors result in increased ripple currents and thus, due to the limited peak inductor current, decrease 24 DC VIN(MIN) * (MAX,M3,BOOST) 100% V I *V 2 * f * RSENSE(MAX,BOOST,MAX) - OUT(MAX) OUT(MAX) RSENSE VIN(MIN) where: DC(MAX,M3,BOOST) is the maximum duty cycle percentage of the M3 switch (see RSENSE Selection and Maximum Current section). f is the switching frequency VRSENSE(MAX,BOOST,MAX) is the maximum current sense voltage in the boost region at maximum duty cycle (see RSENSE Selection and Maximum Current section) Negative values of L(MIN1,BOOST) indicate that the output load current IOUT can't be delivered in the boost region because the inductor current limit is too low. If L(MIN1,BOOST) is too large or is negative, consider reducing the RSENSE resistor value to increase the inductor current limit. Inductor Selection: Subharmonic Oscillations The LT8705A's internal slope compensation circuits will prevent subharmonic oscillations that can otherwise occur when VIN/VOUT is less than 0.5 or greater than 2. The slope compensation circuits will prevent these oscillations provided that the inductance exceeds a minimum value (see the earlier section Inductor Current Sensing and Slope Compensation for more information). Choose an inductance greater than all of the relevant L(MIN) limits discussed below. Negative results can be interpreted as zero. In the boost region, if VOUT can be greater than twice VIN, calculate L(MIN2,BOOST) as follows: L(MIN2,BOOST) = V *V VOUT(MAX) - IN(MIN) OUT(MAX) *RSENSE V OUT(MAX) - VIN(MIN) H 0.08 * f For more information www.linear.com/LT8705A 8705af LT8705A Applications Information In the buck region, if VIN can be greater than twice VOUT, calculate L(MIN1,BUCK) as follows: L(MIN1,BUCK) = VOUT(MAX) *RSENSE VIN(MAX) * 1- VIN(MAX) - VOUT(MIN) H 0.08 * f Inductor Selection: Maximum Current Rating The inductor must have a rating greater than its peak operating current to prevent inductor saturation resulting in efficiency loss. The peak inductor current in the boost region is: IL(MAX,BOOST) IOUT(MAX) * VOUT(MAX) VIN(MIN) DC VIN(MIN) * (MAX,M3,BOOST 100% + A 2 *L * f where DC(MAX,M3,BOOST) is the maximum duty cycle percentage of the M3 switch (see RSENSE Selection and Maximum Current section). The peak inductor current when operating in the buck region is: IL(MAX,BUCK) IOUT(MAX) DC VOUT(MIN) * (MAX,M2,BUCK 100% + A 2 *L * f where DC(MAX,M2,BUCK) is the maximum duty cycle percentage of the M2 switch in the buck region given by: V OUT(MIN) *100% DC(MAX,M2,BUCK ) 1- V IN(MAX) Note that the inductor current can be higher during load transients and if the load current exceeds the expected maximum IOUT(MAX). It can also be higher during startup if inadequate soft-start capacitance is used or during output shorts. Consider using the output current limiting to prevent the inductor current from becoming excessive. Output current limiting is discussed later in the Input/ Output Current Monitoring and Limiting section. Careful board evaluation of the maximum inductor current is recommended. Power MOSFET Selection and Efficiency Considerations The LT8705A requires four external N-channel power MOSFETs, two for the top switches (switches M1 and M4, shown in Figure 3) and two for the bottom switches (switches M2 and M3, shown in Figure 3). Important parameters for the power MOSFETs are the breakdown voltage, VBR,DSS, threshold voltage, VGS,TH, on-resistance, RDS(ON), reverse-transfer capacitance, CRSS (gate-to-drain capacitance), and maximum current, IDS(MAX). The gate drive voltage is set by the 6.35V GATEVCC supply. Consequently, logic-level threshold MOSFETs must be used in LT8705A applications. It is very important to consider power dissipation when selecting power MOSFETs. The most efficient circuit will use MOSFETs that dissipate the least amount of power. Power dissipation must be limited to avoid overheating that might damage the devices. For most buck-boost applications the M1 and M3 switches will have the highest power dissipation where M2 will have the lowest unless the output becomes shorted. In some cases it can be helpful to use two or more MOSFETs in parallel to reduce power dissipation in each device. This is most helpful when power is dominated by I2R losses while the MOSFET is "on". The additional capacitance of connecting MOSFETs in parallel can sometimes slow down switching edge rates and consequently increase total switching power losses. The following sections provide guidelines for calculating power consumption of the individual MOSFETs. From a known power dissipation, the MOSFET junction temperature can be obtained using the following formula: TJ = TA + P * RTH(JA) 8705af For more information www.linear.com/LT8705A 25 LT8705A Applications Information TJ is the junction temperature of the MOSFET TA is the ambient air temperature P is the power dissipated in the MOSFET RTH(JA) is the MOSFET's thermal resistance from the junction to the ambient air. Refer to the manufacturer's data sheet. RTH(JA) normally includes the RTH(JC) for the device plus the thermal resistance from the case to the ambient temperature RTH(JC). Compare the calculated value of TJ to the manufacturer's data sheets to help choose MOSFETs that will not overheat. Switch M1: The power dissipation in switch M1 comes from two primary components: (1) I2R power when the switch is fully turned "on" and inductor current is flowing through the drain to source connections and (2) power dissipated while the switch is turning "on" or "off". As the switch turns "on" and "off" a combination of high current and high voltage causes high power dissipation in the MOSFET. Although the switching times are short, the average power dissipation can still be significant and is often the dominant source of power in the MOSFET. Depending on the application, the maximum power dissipation in the M1 switch can happen in the buck region when VIN is highest, VOUT is highest, and switching power losses are greatest or in the boost region when VIN is smallest, VOUT is highest and M1 is always on. Switch M1 power consumption can be approximated as: PM1 = PI2R +PSWITCHING V OUT *IOUT 2 * RDS(ON) * VIN + ( VIN *IOUT * f * tRF1) W (BUCK REGION) V 2 OUT *IOUT * RDS(ON) * VIN tRF1 is the average of the SW1 pin rise and fall times. Typical values are 20ns to 40ns depending on the MOSFET capacitance and VIN voltage. is a normalization factor (unity at 25C) accounting for the significant variation in MOSFET on-resistance with temperature, typically about 0.4%/C, as shown in Figure 10. For a maximum junction temperature of 125C, using a value = 1.5 is reasonable. 2.0 NORMALIZED ON-RESISTANCE () where: 1.5 1.0 0.5 0 -50 50 100 0 JUNCTION TEMPERATURE (C) 150 8705A F10 Figure 10. Normalized MOSFET RDS(ON) vs Temperature Since the switching power (PSWITCHING) often dominates, look for MOSFETs with lower CRSS or consider operating at a lower frequency to minimize power loss and increase efficiency. Switch M2: In most cases the switching power dissipation in the M2 switch is quite small and I2R power losses dominate. I2R power is greatest in the buck region where the switch operates as the synchronous rectifier. Higher VIN and lower VOUT causes the M2 switch to be "on" for the most amount of time, leading to the highest power consumption. The M2 switch power consumption in the buck region can be approximated as: V -V P(M2,BUCK) IN OUT *IOUT(MAX)2 *RDS(ON) * W VIN Switch M3: Switch M3 operates in the boost and buck-boost regions as a control switch. Similar to the M1 switch, the power dissipation comes from I2R power and switching power. The maximum power dissipation is when VIN is the lowest and VOUT is the highest. The following expres- + 0W (BOOST REGION) where: the PSWITCHING term is 0 in the boost region 8705af 26 For more information www.linear.com/LT8705A LT8705A Applications Information sion approximates the power dissipation in the M3 switch under those conditions: PM3 =PI2R +PSWITCHING ( VOUT - VIN ) * VOUT *IOUT2 *RDS(ON) * VIN2 t + VOUT2 *IOUT * f * RF2 W VIN where the total power is 0 in the buck region. tRF2 is the average of the SW2 pin rise and fall times and, similar to tRF1, is typically 20ns to 40ns. As with the M1 switch, the switching power (PSWITCHING) often dominates. Look for MOSFETs with lower CRSS or consider operating at a lower frequency to minimize power loss and increase efficiency. Switch M4: In most cases the switching power dissipation in the M4 switch is quite small and I2R power losses dominate. I2R power is greatest in the boost region where the switch operates as the synchronous rectifier. Lower VIN and higher VOUT increases the inductor current for a given IOUT, leading to the highest power consumption. The M4 switch power consumption in the boost region can be approximated as: V P(M4,BOOST) OUT *IOUT2 * *RDS(ON) W VIN Gate Resistors: In some cases it can be beneficial to add 1 to 10 of resistance between some of the NMOS gate pins and their respective gate driver pins on the LT8705A (i.e., TG1, BG1, TG2, BG2). Due to parasitic inductance and capacitance, ringing can occur on SW1 or SW2 when low capacitance MOSFETs are turned on/off too quickly. The ringing can be of greatest concern when operating the MOSFETs or the LT8705A near the rated voltage limits. Additional gate resistance slows the switching speed, minimizing the ringing. Excessive gate resistance can have two negative side effects on performance: 1. Slowing the switch transition times can also increase power dissipation in the switch. This is described above in the Switch M1 and Switch M3 sections. 2. Capacitive coupling from the SW1 or SW2 pin to the switch gate node can turn it on when it's supposed to be off, thus increasing power dissipation. With too much gate resistance, this would most commonly happen to the M2 switch when SW1 is rising. Careful board evaluation should be performed when optimizing the gate resistance values. SW1 and SW2 pin ringing can be affected by the inductor current levels, therefore board evaluation should include measurements at a wide range of load currents. When performing PCB measurements of the SW1 and SW2 pins, be sure to use a very short ground post from the PCB ground to the scope probe ground sleeve in order to minimize false inductive voltages readings. CIN and COUT Selection Input and output capacitance is necessary to suppress voltage ripple caused by discontinuous current moving in and out of the regulator. A parallel combination of capacitors is typically used to achieve high capacitance and low ESR (equivalent series resistance). Dry tantalum, special polymer, aluminum electrolytic and ceramic capacitors are all available in surface mount packages. Capacitors with low ESR and high ripple current ratings, such as OS-CON and POSCAP are also available. Ceramic capacitors should be placed near the regulator input and output to suppress high frequency switching spikes. A ceramic capacitor, of at least 1F, should also be placed from VIN to GND as close to the LT8705A pins as possible. Due to their excellent low ESR characteristics ceramic capacitors can significantly reduce input ripple voltage and help reduce power loss in the higher ESR bulk capacitors. X5R or X7R dielectrics are preferred, as these materials retain their capacitance over wide voltage and temperature ranges. Many ceramic capacitors, particularly 0805 or 0603 case sizes, have greatly reduced capacitance at the desired operating voltage. Input Capacitance: Discontinuous input current is highest in the buck region due to the M1 switch toggling on and off. Make sure that the CIN capacitor network has low enough ESR and is sized to handle the maximum RMS current. For buck operation, the input RMS current is given by: IRMS IOUT(MAX) * VOUT VIN * -1 VIN VOUT 8705af For more information www.linear.com/LT8705A 27 LT8705A Applications Information This formula has a maximum at VIN = 2VOUT, where IRMS = IOUT(MAX)/2. This simple worst-case condition is commonly used for design because even significant deviations do not offer much relief. The maximum input ripple due to the voltage drop across the ESR is approximately: V(BUCK,ESR) VIN(MAX) *IOUT(MAX) VOUT(MIN) *ESR Output Capacitance: The output capacitance (COUT) is necessary to reduce the output voltage ripple caused by discontinuities and ripple in the output and load currents. The effects of ESR and the bulk capacitance must be considered when choosing the right capacitor for a given output ripple voltage. The steady-state output ripple due to charging and discharging the bulk output capacitance is given by the following equations: V(BOOST,CAP ) IOUT * ( VOUT - VIN ) V for VOUT > VIN COUT * VIN * f V VOUT * 1- OUT VIN V(BUCK,CAP) V for VOUT < VIN 2 8 *L * f *COUT The maximum output ripple due to the voltage drop across the ESR is approximately: V(BOOST,ESR) VOUT(MAX) *IOUT(MAX) VIN(MIN) *ESR As with CIN, multiple capacitors placed in parallel may be needed to meet the ESR and RMS current handling requirements. Schottky Diode (D1, D2) Selection The Schottky diodes, D1 and D2, shown in Figure 1, conduct during the dead time between the conduction of the power MOSFET switches. They are intended to prevent the body diodes of synchronous switches M2 and M4 from turning on and storing charge. For example, D2 significantly reduces reverse-recovery current between switch M4 turn-off and switch M3 turn-on, which improves converter efficiency, reduces switch M3 power dissipation and reduces noise in the inductor current sense resistor (RSENSE) when M3 turns on. In order for the diode to be effective, the inductance between it and the synchronous switch must be as small as possible, mandating that these components be placed adjacently. For applications with high input or output voltages (typically >40V) avoid Schottky diodes with excessive reverseleakage currents particularly at high temperatures. Some ultralow VF diodes will trade off increased high temperature leakage current for reduced forward voltage. Diode D1 can have a reverse voltage up to VIN and D2 can have a reverse voltage up to VOUT. The combination of high reverse voltage and current can lead to self heating of the diode. Besides reducing efficiency, this can increase leakage current which increases temperatures even further. Choose packages with lower thermal resistance (JA) to minimize self heating of the diodes. Topside MOSFET Driver Supply (CB1, DB1, CB2, DB2) The top MOSFET drivers (TG1 and TG2) are driven digitally between their respective SW and BOOST pin voltages. The BOOST voltages are biased from floating bootstrap capacitors CB1 and CB2, which are normally recharged through external silicon diodes DB1 and DB2 when the respective top MOSFET is turned off. The capacitors are charged to about 6.3V (about equal to GATEVCC) forcing the VBOOST1-SW1 and VBOOST2-SW2 voltages to be about 6.3V. The boost capacitors CB1 and CB2 need to store about 100 times the gate charge required by the top switches M1 and M4. In most applications, a 0.1F to 0.47F, X5R or X7R dielectric capacitor is adequate. The bypass capacitance from GATEVCC to GND should be at least ten times the CB1 or CB2 capacitance. Boost Capacitor Charge Control Block: When the LT8705A operates exclusively in the buck or boost region, one of the top MOSFETs, M1 or M4, can be constantly on. This prevents the respective bootstrap capacitor, CB1 or CB2, from being recharged through the silicon diode, DB1 or DB2. The Boost Capacitor Charge Control block (see Figure 1) keeps the appropriate BOOST pin charged in these cases. When the M1 switch is always on (boost region), 8705af 28 For more information www.linear.com/LT8705A LT8705A Applications Information current is automatically drawn from the CSPOUT and/or BOOST2 pins to charge the BOOST1 capacitor as needed. When the M4 switch is always on (buck region) current is drawn from the CSNIN and/or BOOST1 pins to charge the BOOST2 capacitor. Because of this function, CSPIN and CSNIN should be connected to a potential close to VIN. Tie both pins to VIN if they are not being used. Also, CSPOUT and CSNOUT should always be tied to a potential close to VOUT, or be tied directly to VOUT if not being used. with the internal precision voltage reference (typically 1.207V) by the error amplifier EA4. The output voltage is given by the equation: Boost Diodes DB1 and DB2: Although Schottky diodes have the benefit of low forward voltage drops, they can exhibit high reverse current leakage and have the potential for thermal runaway under high voltage and temperature conditions. Silicon diodes are thus recommended for diodes DB1 and DB2. Make sure that DB1 and DB2 have reverse breakdown voltage ratings higher than VIN(MAX) and VOUT(MAX) and have less than 1mA of reverse leakage current at the maximum operating junction temperature. Make sure that the reverse leakage current at high operating temperatures and voltages won't cause thermal runaway of the diode. By connecting a resistor divider between VIN, FBIN and GND, the FBIN pin provides a means to regulate the input voltage or to create an undervoltage lockout function. Referring to error amplifier EA3 in the Block Diagram, when FBIN is lower than the 1.205V reference VC is pulled low. For example, if VIN is provided by a relatively high impedance source (i.e., a solar panel) and the current draw pulls VIN below a preset limit, VC will be reduced, thus reducing current draw from the input supply and limiting the voltage drop. Note that using this function in forced continuous mode (MODE pin low) can result in current being drawn from the output and forced into the input. If this behavior is not desired then use discontinuous or Burst Mode operation. In some cases it is recommended that up to 5 of resistance is placed in series with DB1 and DB2. The resistors reduce surge currents in the diodes and can reduce ringing at the SW and BOOST pins of the IC. Since SW pin ringing is highly dependent on PCB layout, SW pin edge rates and the type of diodes used, careful measurements directly at the SW pins of the IC are recommended. If required, a single resistor can be placed between GATEVCC and the common anodes of DB1 and DB2 (as in the front page application) or by placing separate resistors between the cathodes of each diode and the respective BOOST pins. Excessive resistance in series with DB1 and DB2 can reduce the BOOST-SW capacitor voltage when the M2 or M3 on-times are very short and should be avoided. Output Voltage The LT8705A output voltage is set by an external feedback resistive divider carefully placed across the output capacitor. The resultant feedback signal (FBOUT) is compared R VOUT = 1.207V * 1+ FBOUT1 RFBOUT2 where RFBOUT1 and RFBOUT2 are shown in Figure 1. Input Voltage Regulation or Undervoltage Lockout To set the minimum or regulated input voltage use: R VIN(MIN) = 1.205V * 1+ FBIN1 RFBIN2 where RFBIN1 and RFBIN2 are shown in Figure 1. Make sure to select RFBIN1 and RFBIN2 such that FBIN doesn't exceed 30V (absolute maximum rating) under maximum VIN conditions. This same technique can be used to create an undervoltage lockout if the LT8705A is NOT in forced continuous mode. When in Burst Mode operation or discontinuous mode, forcing VC low will stop all switching activity. Note that this does not reset the soft-start function, therefore resumption of switching activity will not be accompanied by a soft-start. 8705af For more information www.linear.com/LT8705A 29 LT8705A Applications Information Input/Output Current Monitoring and Limiting to the Boost Capacitor Charge Control block (also see Figure 1) and can draw current in certain conditions. In addition, all four of the current sense pins can draw bias current under normal operating conditions. As such, do not place resistors in series with any of the CSxIN or CSxOUT pins. The LT8705A has independent input and output current monitor circuits that can be used to monitor and/or limit the respective currents. The current monitor circuits work as shown in Figures 11 and 12. As described in the Topside MOSFET Driver Supply section, the CSNIN and CSPOUT pins are also connected RSENSE1 FROM DC POWER SUPPLY TO REMAINDER OF SYSTEM INPUT CURRENT CSPIN LT8705A + gm = 1m A7 - FAULT CONTROL CSNIN - TO BOOST CAPACITOR CHARGE CONTROL BLOCK + 1.61V 1.208V EA2 - VC + IMON_IN RIMON_IN CIMON_IN 8705A F11 Figure 11. Input Current Monitor and Limit RSENSE2 FROM CONTROLLER VOUT TO SYSTEM VOUT OUTPUT CURRENT CSPOUT CSNOUT TO BOOST CAPACITOR CHARGE CONTROL BLOCK + gm = 1m LT8705A - A8 - FAULT CONTROL + 1.61V 1.208V EA1 - + IMON_OUT RIMON_OUT VC CIMON_OUT 8705A F12A Figure 12. Output Current Monitor and Limit 8705af 30 For more information www.linear.com/LT8705A LT8705A Applications Information Also, because of their use with the Boost Capacitor Charge Control block, tie the CSPIN and CSNIN pins to VIN and tie the IMON_IN pin to ground when the input current sensing is not in use. Similarly, the CSPOUT and CSNOUT pins should be tied to VOUT and IMON_OUT should be grounded when not in use. The remaining discussion refers to the input current monitor circuit. All discussion and equations are applicable to the output current monitor circuit, substituting pin and device names as appropriate. Current Monitoring: For input current monitoring, current flowing through RSENSE1 develops a voltage across CSPIN and CSNIN which is multiplied by 1mA/V (typical), converting it to a current that is forced out of the IMON_IN pin and into resistor RIMON_IN (Note: Negative CSPIN to CSNIN voltages are not multiplied and no current flows out of IMON_IN in that case). The resulting IMON_IN voltage is then proportional to the input current according to: A VIMON_IN =IRSENSE1 * RSENSE1 *1m *RIMON_IN V For accurate current monitoring, the CSPIN and CSNIN voltages should be kept above 1.5V (CSPOUT and CSNOUT pins should be kept above 0V). Also, the differential voltage VCSPIN-CSNIN should be kept below 100mV due to the limited amount of current that can be driven out of IMON_IN. Finally, the IMON_IN voltage must be filtered with capacitor CIMON_IN because the input current often has ripple and discontinuities depending on the LT8705A's region of operation. CIMON_IN should be chosen by the equation: 100 F CIMON_IN > f *RIMON_IN where f is the switching frequency, to achieve adequate filtering. Additional capacitance, bringing the CIMON_IN total to 0.1F to 1F, may be necessary to maintain loop stability if the IMON_IN pin is used in a constant-current regulation loop. Current Limiting: As shown in Figure 11, IMON_IN voltages exceeding 1.208V (typical) cause the VC voltage to reduce, thus limiting the inductor and input currents. RIMON_IN can be selected for a desired input current limit using: 1.208V RIMON_IN = IRSENSE(LIMIT) *1m A * RSENSE1 V For example, if RSENSE1 is chosen to be 12.5m and the desired input current limit is 4A then: RIMON_IN = 1.208V = 24.2k A 4A *1m *12.5m V Review the Electrical Characteristics and the IMON Output Currents graph in the Typical Performance Characteristics section to understand the operational limits of the IMON_ OUT and IMON_IN currents. Overcurrent Fault: If IMON_IN exceeds 1.61V (typical), a fault will occur and switching activity will stop (see Fault Conditions earlier in the data sheet). The fault current is determined by: 1.61V IRSENSE1(FAULT) = *IRSENSE1(LIMIT) A 1.208V For example, an input current limit set to 4A would have a fault current limit of 5.3A. Output Overvoltage If the output voltage is higher than the value set by the FBOUT resistor divider, the LT8705A will respond according to the mode and region of operation. In forced continuous mode, the LT8705A will sink current into the input (see the Reverse Current Limit discussion in the Applications Information section for more information). In discontinuous mode and Burst Mode operation, switching will stop and the output will be allowed to remain high. 8705af For more information www.linear.com/LT8705A 31 LT8705A Applications Information INTVCC Regulators and EXTVCC Connection The LT8705A features two PNP LDOs (low dropout regulators) that regulate the 6.35V (typical) INTVCC pin from either the VIN or EXTVCC supply pin. INTVCC powers the MOSFET gate drivers via the required GATEVCC connection and also powers the LDO33 pin regulator and much of the LT8705A's internal control circuitry. The INTVCC LDO selection is determined automatically by the EXTVCC pin voltage. When EXTVCC is lower than 6.22V (typical), INTVCC is regulated from the VIN LDO. After EXTVCC rises above 6.4V (typical), INTVCC is regulated by the EXTVCC LDO instead. Overcurrent protection circuitry typically limits the maximum current draw from either LDO to 127mA. When GATEVCC and INTVCC are below 4.65V, during start-up or during an overload condition, the typical current limit is reduced to 42mA. The INTVCC pin must be bypassed to ground with a minimum 4.7F ceramic capacitor placed as close as possible to the INTVCC and GND pins. An additional ceramic capacitor should be placed as close as possible to the GATEVCC and GND pins to provide good bypassing to supply the high transient current required by the MOSFET gate drivers. 1F to 4.7F is recommended. Power dissipated in the INTVCC LDOs must be minimized to improve efficiency and prevent overheating of the LT8705A. Since LDO power dissipation is proportional to the input voltage and VIN can be as high as 80V in some applications, the EXTVCC pin is available to regulate INTVCC from a lower input voltage. The EXTVCC pin is connected to VOUT in many applications since VOUT is often regulated to a much lower voltage than the maximum VIN. During start-up, power for the MOSFET drivers, control circuits and the LDO33 pin is derived from VIN until VOUT/ EXTVCC rises above 6.4V, after which the power is derived from VOUT/EXTVCC. This works well, for example, in a case where VOUT is regulated to 12V and the maximum VIN voltage is 40V. EXTVCC can be floated or grounded when not in use or can also be connected to an external power supply if available. The maximum current drawn through the INTVCC LDO occurs under the following conditions: 1. Large (capacitive) MOSFETs are being driven at high frequencies. 2. VIN and/or VOUT is high, thus requiring more charge to turn the MOSFET gates on and off. 3. The LDO33 pin output current is high. 4. In some applications, LDO current draw is maximum when the part is operating in the buck-boost region where VIN is close to VOUT since all four MOSFETs are switching. To check for overheating find the operating conditions that consume the most power in the LT8705A (PLT8705A). This will often be under the same conditions just listed that maximize LDO current. Under these conditions monitor the CLKOUT pin duty cycle to measure the approximate die temperature. See the Junction Temperature Measurement section for more information. Powering INTVCC from VOUT/EXTVCC can also provide enough gate drive when VIN drops as low as 2.8V. This allows the part to operate with a reduced input voltage after the output gets into regulation. The following list summarizes the three possible connections for EXTVCC: 1. EXTVCC left open (or grounded). This will cause INTVCC to be powered from VIN through the internal 6.35V regulator at the cost of a small efficiency penalty. 2. EXTVCC connected directly to VOUT (VOUT > 6.4V). This is the normal connection for the regulator and usually provides the highest efficiency. 3. EXTVCC connected to an external supply. If an external supply is available greater than 6.4V (typical) it may be used to power EXTVCC. 8705af 32 For more information www.linear.com/LT8705A LT8705A Applications Information Loop Compensation Table 1. Voltage Lockout Conditions The loop stability is affected by a number of factors including the inductor value, output capacitance, load current, VIN, VOUT and the VC resistor and capacitors. The LT8705A uses internal transconductance error amplifiers driving VC to help compensate the control loop. For most applications a 3.3nF series capacitor at VC is a good value. The parallel capacitor (from VC to GND) is typically 1/10th the value of the series capacitor to filter high frequency noise. A larger VC series capacitor value may be necessary if the output capacitance is reduced. A good starting value for the VC series resistor is 20k. Lower resistance will improve stability but will slow the loop response. Use a trim pot instead of a fixed resistor for initial bench evaluation to determine the optimum value. LDO33 Pin Regulator The LT8705A includes a low dropout regulator (LDO) to regulate the LDO33 pin to 3.3V. This pin can be used to power external circuitry such as a microcontroller or other desired peripherals. The input supply for the LDO33 pin regulator is INTVCC. Therefore INTVCC must have sufficient voltage, typically >4.0V, to properly regulate LDO33. The LDO33 and INTVCC regulators are enabled by the SHDN pin and are not affected by SWEN. The LDO33 pin regulator has overcurrent protection circuitry that typically limits the output current to 17.25mA. An undervoltage lockout monitoring LDO disables switching activity when LDO33 falls below 3.04V (typical). LDO33 should be bypassed locally with 0.1F or more. Voltage Lockouts The LT8705A contains several voltage detectors to make sure the chip is under proper operating conditions. Table 1 summarizes the pins that are monitored and also indicates the state that the LT8705A will enter if an under or overvoltage condition is detected. The conditions are listed in order of priority from top to bottom. If multiple over/undervoltage conditions are detected, the chip will enter the state listed highest on the table. PIN APPROXIMATE VOLTAGE CHIP STATE CONDITION (FIGURE 2) VIN <2.5V Chip Off SHDN <1.18V Chip Off INTVCC and GATEVCC <4.65V Switcher Off SWEN <1.18V Switcher Off LDO33 <3.04 Switcher Off IMON_IN >1.61V Fault IMON_OUT >1.61V Fault FBIN <1.205V -- READ SECTION Operation: Start-Up Operation: Fault Conditions Applications Information: Input Voltage Regulation or Undervoltage Lockout Due to their accurate thresholds, configurable undervoltage lockouts (UVLOs) can be implemented using the SHDN, SWEN and in some cases, FBIN pin. The UVLO function sets the turn on/off of the LT8705A at a desired minimum input voltage. For example, a resistor divider can be connected between VIN, SHDN and GND as shown in Figures 1 and 15. From the Electrical Characteristics, SHDN has typical rising and falling thresholds of 1.234V and 1.184V respectively. The falling threshold for turning off switching activity can be chosen using: RSHDN1 = ( RSHDN2 * V(IN,CHIP_OFF,FALLING) - 1.184V 1.184V ) For example, choosing RSHDN2 = 20k and a falling VIN threshold of 5.42V results in: RSHDN1 = 20k * (5.42V - 1.184V ) = 71.5k 1.184V The rising threshold for enabling switching activity would be: V(IN,CHIP_OFF,RISING) = V(IN,CHIP_OFF,FALLING) * 1.234V 1.184V or 5.65V in this example. 8705af For more information www.linear.com/LT8705A 33 LT8705A Applications Information Similar calculations can be used to select a resistor divider connected to SWEN that would stop switching activity during an undervoltage condition. Make sure that the divider doesn't cause SWEN to exceed 7V (absolute maximum rating) under maximum VIN conditions. Using the FBIN pin as an undervoltage lockout is discussed in the Input Voltage Regulation or Undervoltage Lockout section. Inductor Current Sense Filtering Certain applications may require filtering of the inductor current sense signals due to excessive switching noise that can appear across RSENSE. Higher operating voltages, higher values of RSENSE, and more capacitive MOSFETs will all contribute additional noise across RSENSE when the SW pins transition. The CSP/CSN sense signals can be filtered by adding one of the RC networks shown in Figures 13a and 13b. Most PC board layouts can be drawn to accommodate either network on the same board. The network should be placed as close as possible to the IC. The network in Figure 13b can reduce common mode noise seen by the CSP and CSN pins of the LT8705A at the expense of some increased ground trace noise as current passes through the capacitors. A short direct path from the capacitor grounds to the IC ground should be used on the PC board. Resistors greater than 10 should be avoided as this can increase offset voltages at the CSP/CSN pins. The RC product should be kept to less than 30ns. 10 RSENSE 10 CSP 1nF LT8705A CSN 8705A F13a (13a) 10 RSENSE 10 CSP 1nF LT8705A CSN 1nF 8705A F13b (13b) Figure 13. Inductor Current Sense Filter Junction Temperature Measurement The duty cycle of the CLKOUT signal is linearly proportional to the die junction temperature, TJ. Measure the duty cycle of the CLKOUT signal and use the following equation to approximate the junction temperature: TJ DCCLKOUT - 35.9% C 0.329% where DCCLKOUT is the CLKOUT duty cycle in % and TJ is the die junction temperature in C. The actual die temperature can deviate from the above equation by 10C Thermal Shutdown If the die junction temperature reaches approximately 165C, the part will go into thermal shutdown. The power switch will be turned off and the INTVCC and LDO33 regulators will be turned off (see Figure 2). The part will be re-enabled when the die temperature has dropped by ~5C (nominal). After re-enabling, the part will start in the switcher off state as shown in Figure 2. The part will then initialize, perform a soft-start, then enter normal operation as long as the die temperature remains below approximately 165C. Efficiency Considerations The efficiency of a switching regulator is equal to the output power divided by the input power times 100%. It is often useful to analyze individual losses to determine what is limiting the efficiency and which change would produce the most improvement. Although all dissipative elements in the circuit produce losses, four main sources account for most of the losses in LT8705A circuits: 1. Switching losses. These losses arises from the brief amount of time switch M1 or switch M3 spends in the saturated region during switch node transitions. Power loss depends upon the input voltage, load current, driver strength and MOSFET capacitance, among other factors. See the Power MOSFET Selection and Efficiency Considerations section for more details. 2. DC I2R losses. These arise from the resistances of the MOSFETs, sensing resistors, inductor and PC board traces and cause the efficiency to drop at high output currents. 8705af 34 For more information www.linear.com/LT8705A LT8705A Applications Information 3. INTVCC current. This is the sum of the MOSFET driver current, LDO33 pin current and control currents. The INTVCC regulator's input voltage times the current represents lost power. This loss can be reduced by supplying INTVCC current through the EXTVCC pin from a high efficiency source, such as the output or alternate supply if available. Also, lower capacitance MOSFETs can reduce INTVCC current and power loss. 4. CIN and COUT loss. The input capacitor has the difficult job of filtering the large RMS input current to the regulator in buck mode. The output capacitor has the more difficult job of filtering the large RMS output current in boost mode. Both CIN and COUT are required to have low ESR to minimize the AC I2R loss and sufficient capacitance to prevent the RMS current from causing additional upstream losses in fuses or batteries. 5. Other losses. Schottky diodes D1 and D2 are responsible for conduction losses during dead time and light load conduction periods. Inductor core loss occurs predominately at light loads. When making adjustments to improve efficiency, the input current is the best indicator of changes in efficiency. If one makes a change and the input current decreases, then the efficiency has increased. If there is no change in input current, then there is no change in efficiency. VIN SW1 VOUT SW2 L D1 M1 D2 M2 M3 M4 CIN COUT RSENSE LT8705 CKT GND 8705A F14a (14a) SW1 VIN VOUT SW2 L D2 M1 M4 D1 M2 M3 CIN COUT RSENSE LT8705 CKT Circuit Board Layout Checklist GND 8705A F14b The basic circuit board layout requires a dedicated ground plane layer. Also, for high current, a multilayer board provides heat sinking for power components. * The ground plane layer should not have any traces and should be as close as possible to the layer with the power MOSFETs. * The high di/dt path formed by switch M1, switch M2, D1, RSENSE and the CIN capacitor should be compact with short leads and PC trace lengths. The high di/dt path formed by switch M3, switch M4, D2 and the COUT capacitor also should be compact with short leads and PC trace lengths. Two layout examples are shown in Figures 14a and 14b. (14b) Figure 14. Switches Layout * Avoid running signal traces parallel to the traces that carry high di/dt current because they can receive inductively coupled voltage noise. This includes the SW1, SW2, TG1 and TG2 traces to the controller. * Use immediate vias to connect the components (including the LT8705A's GND pins) to the ground plane. Use several vias for each power component. * Minimize parasitic SW pin capacitance by removing GND and VIN copper from underneath the SW1 and SW2 regions. 8705af For more information www.linear.com/LT8705A 35 LT8705A Applications Information * Except under the SW pin regions, flood all unused areas on all layers with copper. Flooding with copper will reduce the temperature rise of power components. Connect the copper areas to a DC net (e.g., quiet GND). * Partition the power ground from the signal ground. The small-signal component grounds should not return to the IC GND through the power ground path. * Place switch M2 and switch M3 as close to the controller as possible, keeping the GND, BG and SW traces short. * Minimize inductance from the sources of M2 and M3 to RSENSE by making the trace short and wide. * Keep the high dV/dT nodes SW1, SW2, BOOST1, BOOST2, TG1 and TG2 away from sensitive small-signal nodes. * The output capacitor (-) terminals should be connected as closely as possible to the (-) terminals of the input capacitor. * Connect the top driver boost capacitor, CB1, closely to the BOOST1 and SW1 pins. Connect the top driver boost capacitor, CB2, closely to the BOOST2 and SW2 pins. * Connect the input capacitors, CIN, and output capacitors, COUT, closely to the power MOSFETs. These capacitors carry the MOSFET AC current in the boost and buck regions. * Connect the FBOUT and FBIN pin resistor dividers to the (+) terminals of COUT and CIN respectively. Small FBOUT/ FBIN bypass capacitors may be connected closely to the LT8705A's GND pin if needed. The resistor connections should not be along the high current or noise paths. * Route current sense traces (CSP/CSN, CSPIN/CSNIN, CSPOUT/CSNOUT) together with minimum PC trace spacing. Avoid having sense lines pass through noisy areas, such as switch nodes. The optional filter network capacitor between CSP and CSN should be as close as possible to the IC. Ensure accurate current sensing with Kelvin connections at the RSENSE resistors. * Connect the VC pin compensation network closely to the IC, between VC and the signal ground pins. The capacitor helps to filter the effects of PCB noise and output voltage ripple voltage from the compensation loop. * Connect the INTVCC and GATEVCC bypass capacitors close to the IC. The capacitors carry the MOSFET drivers' current peaks. 36 Design Example VIN = 8V to 25V VOUT = 12V IOUT(MAX) = 5A f = 350kHz Maximum ambient temperature = 60C RT Selection: Choose the RT resistor for the free-running oscillator frequency using: 43,750 43,750 RT = - 1k = - 1 = 124k 350 fOSC RSENSE Selection: Start by calculating the maximum duty cycle in the boost region: VIN(MIN) *100% DC(MAX,M3,BOOST) 1- VOUT(MAX) 8V = 1- *100% = 33% 12V Next, from the Maximum Inductor Current Sense Voltage vs Duty Cycle graph in the Typical Performance Characteristics section: VRSENSE(MAX,BOOST,MAX) 107mV Next, estimate the maximum and minimum inductor current ripple in the boost and buck regions respectively: IL(MAX,BOOST) = IL(MIN,BUCK) VOUT(MAX) *IOUT(MAX,BOOST) A 100% VIN(MIN) * - 0.5 %Ripple 12V * 5A = 3.75A 100% - 0.5 8V * 40% IOUT(MAX,BUCK) A 100% - 0.5 10% = 5A = 0.53A 100% - 0.5 10% Now calculate the maximum RSENSE values in the boost and buck regions to be: For more information www.linear.com/LT8705A 8705af LT8705A Applications Information RSENSE(MAX,BOOST) = 2 * VRSENSE(MAX,BOOST,MAX) * VIN(MIN) (2 *IOUT(MAX,BOOST) * VOUT(MIN) ) + (IL(MAX,BOOST) * VIN(MIN) ) 2 *107mV * 8V = = 11.4m (2 * 5A *12V ) + (3.75A * 8V ) RSENSE(MAX,BUCK) = = 2 * 86mV (2 * 5A ) - 0.53A ( 2 * 86mV 2 *IOUT(MAX,BUCK) - IL(MIN,BUCK) ) = 18.2m Adding an additional 30% margin, choose RSENSE to be 11.4m/1.3 = 8.7m. Inductor Selection: With RSENSE known, we can now determine the minimum inductor value that will provide adequate load current in the boost region using: L(MIN1,BOOST) VIN(MIN) * DC(MAX,M3,BOOST) 100% H V RSENSE(MAX,BOOST,MAX) IOUT(MAX) * VOUT(MAX) 2* f * - RSENSE VIN(MIN) 33% 8V * 100% = 0.8H = 107mV 5A *12V - 2 * 350kHz * 8.7m 8V To avoid subharmonic oscillations in the inductor current, choose the minimum inductance according to: V *V VOUT(MAX) - IN(MIN) OUT(MAX) *RSENSE V OUT(MAX) - VIN(MIN) L(MIN2,BOOST) = H 0.08 * f 8V *12V * 8.7m 12V - 12V - 8V = -3.7H = 0.08 * 350kHz VOUT(MAX) *RSENSE VIN(MAX) * 1- VIN(MAX) - VOUT(MIN) L(MIN1,BUCK) = 0.08 * f The inductance must be higher than all of the minimum values calculated above. We will choose a 10H standard value inductor for improved margin. MOSFET Selection: The MOSFETs are selected based on voltage rating, CRSS and RDS(ON) value. It is important to ensure that the part is specified for operation with the available gate voltage amplitude. In this case, the amplitude is 6.35V and MOSFETs with an RDS(ON) value specified at VGS = 4.5V can be used. Select M1 and M2: With 25V maximum input voltage, MOSFETs with a rating of at least 30V are used. As we do not yet know the actual thermal resistance (circuit board design and airflow have a major impact) we assume that the MOSFET thermal resistance from junction to ambient is 50C/W. If we design for a maximum junction temperature, TJ(MAX) = 125C, the maximum allowable power dissipation can be calculated. First, calculate the maximum power dissipation: PD(MAX) = PD(MAX) = TJ(MAX) - TA(MAX) R TH(JA) 125C - 60C = 1.3W 50C/W Since maximum I2R power dissipation in the boost region happens when VIN is minimum, we can determine the maximum allowable RDS(ON) for the boost region using: 2 V PM1 =PI2R OUT *IOUT *RDS(ON) * W VIN 12V 2 * 5A *RDS(ON) *1.5 W and therefore 1.3W 8V RDS(ON) < 15.4m The Fairchild FDMS7672 meets the specifications with a maximum RDS(ON) of ~6.9m at VGS = 4.5V (~10m at 125C). Checking the power dissipation in the buck region with VIN maximum and VOUT minimum yields: 12V 25V * 1- * 8.7m 25V - 12V = = 0.6H 0.08 * 350kHz 8705af For more information www.linear.com/LT8705A 37 LT8705A Applications Information PM1 = PI2R +PSWITCHING V OUT *IOUT2 * RDS(ON) * + ( VIN *IOUT * f * tRF1) W VIN 12V * 5A 2 * 6.9m * 1.5 + (25V * 5A * 350k * 20ns) PM1 25V = 0.12W + 0.88W = 1.0W The maximum switching power of 0.88W can be reduced by choosing a slower switching frequency. Since this calculation is approximate, measure the actual rise and fall times on the PCB to obtain a better power estimate. The maximum dissipation in M2 occurs at maximum input voltage when the circuit is operating in the buck region. Using the 6.9m Fairchild FDMS7672 the dissipation is: The Fairchild FDMS7672 can also be used for M3 and M4. Assuming 20ns rise and fall times, the calculated power loss at the minimum 8V input voltage is then 0.82W for M3 and 0.39W for M4 Output Voltage: Output voltage is 12V. Select RFBOUT2 as 20k. RFBOUT1 is: V RFBOUT1 = OUT - 1 *RFBOUT2 1.207V Select RFBOUT1 as 178k. Both RFBOUT1 and RFBOUT2 should have a tolerance of no more than 1%. Capacitors: A low ESR (5m) capacitor network for CIN is selected. In this mode, the maximum ripple is: V -V P(M2,BUCK) IN OUT *IOUT(MAX)2 *RDS(ON) * W VIN V(BUCK,ESR) 25V - 12V 2 P(M2,BUCK) * (5A ) * 6.9m *1.5 = 0.13W 25V V(BUCK,ESR) Select M3 and M4: With 12V output voltage we need MOSFETs with 20V or higher rating. The highest dissipation occurs in the boost region when input voltage is minimum and output current is highest. For switch M3 the dissipation is: PM3 =PI2R +PSWITCHING VIN(MAX) *IOUT(MAX) VOUT(MIN) 25V * 5A * 5m = 52mV 12V assuming ESR dominates the ripple. Having 5m of ESR for the COUT network sets the maximum output voltage ripple at: V(BOOST,ESR) V(BOOST,ESR) ( VOUT - VIN ) * VOUT *IOUT2 *RDS(ON) * 2 VIN *ESR VOUT(MAX) *IOUT(MAX) VIN(MIN) *ESR 12V * 5A * 5m = 37.5mV 8V assuming ESR dominates the ripple. t + VOUT2 *IOUT * f * RF2 W VIN as described in the Power MOSFET Selection and Efficiency Considerations section. The maximum dissipation in switch M4 is: V OUT(MAX) P(M4,BOOST ) *IOUT2 * *RDS(ON) W VIN(MIN) 8705af 38 For more information www.linear.com/LT8705A LT8705A Applications Information VIN 36V TO 80V L1 22H M1 x2 + CIN2 4.7F x4 CIN1 220F x2 M3 x2 M2 TO DIODE DB1 0.22F 2* TG1 BOOST1 SW1 BG1 CSP M4 1nF 10 1nF 10 TO DIODE DB2 392k 2** CSN GND BG2 SW2 BOOST2 TG2 CSNIN CSPOUT CSPIN CSNOUT EXTVCC SHDN FBOUT SWEN INTVCC LDO33 SRVO_IIN SS SRVO_IOUT IMON_IN 1F 4.7F VC CLKOUT IMON_OUT SYNC 1F 220pF 3.3nF 8705A F15a Efficiency vs Output Current (Buck Region) 100 VIN = 36V VOUT = 48V FCM VIN = 72V VOUT = 48V FCM 90 80 70 60 50 40 30 70 60 50 40 30 20 20 COILCRAFT SER2918H-223 WURTH 74435572200 10 0 DB2 TO TO BOOST1 BOOST2 *2 FROM TG1 TO EACH SEPERATE M1 GATE **2 FROM BG2 TO EACH SEPERATE M3 GATE EFFICIENCY (%) EFFICIENCY (%) 80 DB1 202kHz Efficiency vs Output Current (Boost Region) 90 4 56.2k CIN1, COUT2: 220F, 100V CIN2, COUT1: 4.7F, 100V, TDK C453X7S2A475M DB1, DB2: CENTRAL SEMI CMMR1U-02-LTE L1: 22H, WURTH 74435572200 OR COILCRAFT SER2918H-223 M1, M3: FAIRCHILD FDMS86104 M2, M4: FAIRCHILD FDMS86101 100 4.7F SRVO_FBOUT RT 215k 4.7F SRVO_FBIN FBIN 20k 10k GATEVCC LT8705A MODE 71.5k VOUT 48V COUT2 5A 220F x2 0.22F 10m VIN 100k + COUT1 4.7F x6 10 1000 100 LOAD CURRENT (mA) COILCRAFT SER2918H-223 WURTH 74435572200 10 10000 0 10 8705A F15b 1000 100 LOAD CURRENT (mA) 10000 8705A F15c Note: See the front page and the Typical Performance Characteristics section for more curves from this application circuit using the Coilcraft inductor. The smaller Wurth inductor is also suitable in place of the Coilcraft inductor with some loss in efficiency. Figure 15. Telecom Voltage Stabilizer 8705af For more information www.linear.com/LT8705A 39 LT8705A Typical Applications Supercapacitor Backup Supply TO LOADS DIN VIN 12V VINP + 25m L1 2.2H M1 CIN1 x2 CIN2 x3 M2 TO DIODE DB2 3m 2 TG1 BOOST1 SW1 BG1 CSP CSN GND 2 BG2 SW2 BOOST2 TG2 CSNIN CSPOUT CSPIN CSNOUT EXTVCC SHDN FBOUT SWEN INTVCC LDO33 SRVO_FBIN IMON_IN 20k 1k TO TO BOOST1 BOOST2 SRVO_IOUT 2N3904* 20k VC 124k CLKOUT IMON_OUT SYNC 24k 14.3k 4.7F 1F 15nF 220pF DB2 DB1 SRVO_IIN SS 71.5k 4.7F 4 SRVO_FBOUT RT 1F 10k 4.7F GATEVCC LT8705A FBIN 113k 1.2k x6 115k MODE 15V VOUT 15V COUT2 x2 CSC x6 0.22F VIN 1k + COUT1 x3 M3 TO DIODE DB1 0.22F 100k 25m M4 47.5k 350kHz 100nF 100nF 8705A TA02a CIN1, COUT2: 100F, 20V SANYO OS-CON 205A100M CIN2, COUT1: 22F, 25V, TDK C4532X741E226M CSC: 60F, 2.5V COOPER BUSSMAN HB1840-2R5606-R 12V INPUT DIN: APPROPRIATE 2A SCHOTTKY DIODE OR IDEAL DIODE SUCH AS LTC4358, LTC4412, LTC4352, ETC. DB1, DB2: CENTRAL SEMI CMMR1U-02-LTE L1: 2.2H, VISHAY IHLP-5050CE-01-2R2-M-01 M1-M4: FAIRCHILD FDMS7698 LOADS 12V LOADS POWER FLOW DIN 25m 113k 20k POWER FLOW DIN 25m INPUT CURRENT IN EXCESS OF 2A WILL DRAW FROM SUPER CAPS 25m 0V INPUT LIMIT CAPACITOR CHARGING CURRENT TO 1A 115k REGULATE CAPACITORS TO 15V 10k 25m CSC 1.2k CSC 1.2k 1.2k CSC 1.2k CSC 1.2k CSC 1.2k CSC 1.2k CSC 1.2k CSC 1.2k CSC 1.2k CSC 1.2k CSC 1.2k CSC Charging VOUT to 15V with 1A Current 8705A TA02b 113k REGULATE LOADS TO 8V 20k 115k 10k Remove VIN. Loads (4A Draw) Regulated to 8V from Supercaps 8705A TA02c VOUT 15V 5V/DIV VIN 5V/DIV VOUT 5V/DIV VINP 5V/DIV IL 5A/DIV 8V IL 5A/DIV 20SEC/DIV 40 *INPUT SIDE OVERVOLTAGE PROTECTION WHEN CONVERTER IS DRAWING CURRENT FROM THE SUPER CAPACITORS 8705A TA02d 3SEC/DIV For more information www.linear.com/LT8705A 8705A TA02e 8705af LT8705A Typical Applications 12V, 15A Output Converter Accepts 7.5V to 55V Input VIN 7.5V TO 55V (INCREASED VOUT RIPPLE FOR VIN > 50V) L1, 6.8H M1 + CIN2 4.7F x5 CIN1 220F x3 M2 TO DIODE DB1 0.22F 2 M3 1nF 8.2 1nF 8.2 RSENSE 3m + 0.22F CSN 102k GND BG2 SW2 BOOST2 TG2 CSNIN CSPOUT CSPIN CSNOUT EXTVCC SHDN FBOUT SWEN INTVCC LDO33 11.3k GATEVCC LT8705A MODE 4.7F SRVO_FBIN FBIN 86.6k 4.7F SRVO_FBOUT RT SRVO_IIN SS SRVO_IOUT 4 DB1 IMON_IN 1F 20k VC 226k CLKOUT SYNC DB2 TO TO BOOST1 BOOST2 IMON_OUT 10k 1F 4.7F COUT2 330F x3 2 VIN 100k COUT1 10F x3 TO DIODE DB2 5.6nF TG1 BOOST1 SW1 BG1 CSP VOUT 12V 15A M4 220pF 15nF 190kHz 8705A TA03a M1: INFINEON BSC028N06NS M2: INFINEON BSC039N06NS M3, M4: INFINEON BSC015NE2LS5I L1: COILCRAFT SER2915H-682, 6.8H CIN1: 220F, 100V CIN2: 4.7F, 100V, TDK C453X7S2A475M COUT1: 10F, 25V, TDK C4532X7R1E106M COUT2: 330F, 25V, PANASONIC 25SEPF330M RSENSE: SUSUMU 3m, KRL6432E-M-R003-F-T1 Efficiency vs Output Current 100 EFFICIENCY (%) 96 92 88 VIN = 7.5V VIN = 20V VIN = 35V VIN = 50V 84 80 Load Step 3 Input Transient (8V to 50V) VOUT 0.5V/DIV VOUT 0.2V/DIV IL 5A/DIV 9 6 LOAD CURRENT (A) 12 15 8705A TA03b Start-Up Waveforms VOUT 5V/DIV IL 5A/DIV VIN 20V/DIV 500s/DIV VIN = 12V VOUT = 12V LOAD STEP = 5A TO 10A 0 8705A TA03c ILOAD = 5A VOUT = 12V 20ms/DIV 8705A TA03d VIN = 28V 1.67 LOAD 10ms/DIV 8705A TA03e 8705af For more information www.linear.com/LT8705A 41 LT8705A Package Description Please refer to http://www.linear.com/product/LT8705A#packaging for the most recent package drawings. UHF Package 38-Lead Plastic QFN (5mm x 7mm) (Reference LTC DWG # 05-08-1701 Rev C) 0.70 0.05 5.50 0.05 5.15 0.05 4.10 0.05 3.00 REF 3.15 0.05 PACKAGE OUTLINE 0.25 0.05 0.50 BSC 5.5 REF 6.10 0.05 7.50 0.05 RECOMMENDED SOLDER PAD LAYOUT APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED 5.00 0.10 0.75 0.05 PIN 1 NOTCH R = 0.30 TYP OR 0.35 x 45 CHAMFER 3.00 REF 37 0.00 - 0.05 38 0.40 0.10 PIN 1 TOP MARK (SEE NOTE 6) 1 2 5.15 0.10 5.50 REF 7.00 0.10 3.15 0.10 (UH) QFN REF C 1107 0.200 REF 0.25 0.05 R = 0.125 TYP 0.50 BSC R = 0.10 TYP BOTTOM VIEW--EXPOSED PAD NOTE: 1. DRAWING CONFORMS TO JEDEC PACKAGE OUTLINE M0-220 VARIATION WHKD 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 42 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.20mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE For more information www.linear.com/LT8705A 8705af LT8705A Package Description Please refer to http://www.linear.com/product/LT8705A#packaging for the most recent package drawings. FE Package Package Variation: FE38 (31) 38-Lead Plastic TSSOP (4.4mm) (Reference LTC DWG # 05-08-1865 Rev B) Exposed Pad Variation AB 4.75 REF 38 9.60 - 9.80* (.378 - .386) 4.75 REF (.187) 20 6.60 0.10 4.50 REF 2.74 REF SEE NOTE 4 6.40 2.74 REF (.252) (.108) BSC 0.315 0.05 1.05 0.10 0.50 BSC RECOMMENDED SOLDER PAD LAYOUT 4.30 - 4.50* (.169 - .177) 0.50 - 0.75 (.020 - .030) 0.09 - 0.20 (.0035 - .0079) NOTE: 1. CONTROLLING DIMENSION: MILLIMETERS 2. DIMENSIONS ARE IN MILLIMETERS (INCHES) 3. DRAWING NOT TO SCALE 1 19 PIN NUMBERS 23, 25, 27, 29, 31, 33 AND 35 ARE REMOVED 0.25 REF 1.20 (.047) MAX 0 - 8 0.50 (.0196) BSC 0.17 - 0.27 (.0067 - .0106) TYP 0.05 - 0.15 (.002 - .006) FE38 (AB) TSSOP REV B 0910 4. RECOMMENDED MINIMUM PCB METAL SIZE FOR EXPOSED PAD ATTACHMENT *DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.150mm (.006") PER SIDE 8705af Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representaFor more information www.linear.com/LT8705A tion that the interconnection of its circuits as described herein will not infringe on existing patent rights. 43 LT8705A Typical Application 12V Output Converter Accepts 4V to 80V Input (5.5V Minimum to Start) M1 x2 VIN 4V TO 80V (INCREASED VOUT RIPPLE FOR VIN > 60V) + CIN2 x6 CIN1 15H M2 TO DIODE DB1 0.22F 2* TG1 BOOST1 SW1 BG1 CSP 1nF 10 1nF 10 CSN + 0.22F 4m CSPOUT CSPIN CSNOUT FBOUT SWEN INTVCC 4.7F 11.3k GATEVCC LT8705A 4.7F SRVO_FBIN FBIN 4.7F SRVO_FBOUT RT SRVO_IIN SS SRVO_IOUT 4 DB1 IMON_IN 1F VC CLKOUT SYNC CIN1: 220F, 100V CIN2: 4.7F, 100V, TDK C4532X7S2A475M COUT1A, COUT1B: 22F, 25V, TDK C4532X7R1E226M COUT2: 100F, 16V, SANYO OS-CON 16SA100M COUT3: 470F, 16V DB1, DB2: CENTRAL SEMI CMMR1U-02-LTE L1: 15H, WURTH 7443631500 M1, M2: FAIRCHILD FDMS86101 M3, M4: FAIRCHILD FDMS7692 *2 FROM TG1 TO EACH SEPARATE M1 GATE DB2 TO TO BOOST1 BOOST2 IMON_OUT 16.5k 1F 4.7F COUT2 x2 EXTVCC SHDN 215k VOUT 12V 5.0A (VIN 5.5V) COUT3 4.5A (VIN 5.0V) x3 4.0A (VIN 4.5V) 3.5A (VIN 4.0V) 102k MODE 20k + GND BG2 SW2 BOOST2 TG2 CSNIN LDO33 38.3k COUT1B x3 COUT1A x2 TO DIODE DB2 VIN 100k 7m M4 M3 x2 220pF 202kHz 10nF 26.1k 22nF 8705A TA04a Efficiency vs Output Current Input Transient (4V to 80V) 100 VOUT 200mV/DIV EFFICIENCY (%) 95 90 85 80 VIN 20V/DIV VIN = 60V VIN = 40V VIN = 20V VIN = 12V VIN = 5V 0 1 3 2 LOAD CURRENT (A) 4 5 ILOAD = 2A 10ms/DIV 8705A TA04c 8705A TA04c Related Parts PART NUMBER DESCRIPTION COMMENTS LT8390 60V Synchronous 4-Switch Buck-Boost Controller with Spread Spectrum 4V VIN 60V, 1V VOUT 60V, Regulates Output Voltage, Input or Output Current, TSSOP-28, 4mm x 5mm QFN-28 LTC3789 38V Synchronous 4-Switch Buck-Boost DC/DC Controller 4V VIN 38V, 0.8V VOUT 38V, SSOP-28, 4mm x 5mm QFN-28 LTC7813 60V, Low IQ Synchronous Boost + Buck Controller with Adjustable Gate Drive Level 5V to 10V 4.5V VIN 60V, 0.8V VOUT 60V 5mm x 5mm QFN-32 LT3758A High Input Voltage, Boost, Flyback, SEPIC and Inverting Controller 5.5V VIN 100V, Positive or Negative VOUT, 3mm x 3mm DFN-10 and MSOP-10E LTC3115-1 40V, 2A Synchronous Buck-Boost DC/DC Converter 2.7V VIN 40V, 2.7V VOUT 40V, 4mm x 5mm DFN-16, TSSOP-20 LTM 8056 58V Buck-Boost Module Regulator, Adjustable Input and Output Current Limiting 5V VIN 58V, 1.2V VOUT 48V, 15mm x 15mm x 4.92mm BGA Package (R) (R) 8705af 44 Linear Technology Corporation 1630 McCarthy Blvd., Milpitas, CA 95035-7417 For more information www.linear.com/LT8705A (408) 432-1900 FAX: (408) 434-0507 www.linear.com/LT8705A LT 1016 * PRINTED IN USA LINEAR TECHNOLOGY CORPORATION 2016