LM48411 www.ti.com LM48411 SNAS399G - SEPTEMBER 2007 - REVISED MAY 2013 Ultra-Low EMI, Filterless, 2.5W, Stereo, Class D Audio Power Amplifier with E2S Check for Samples: LM48411 FEATURES 1 * 2 * * * * * * * * * 2 E S System Reduces EMI Preserving Audio Quality and Efficiency Output Short Circuit Protection Stereo Class D Operation No Output Filter Required for Inductive Loads Logic Selectable Gain Independent Shutdown Control Minimum External Components "Click and Pop" Suppression Circuitry Micro-Power Shutdown Mode Available in Space-Saving 0.5mm Pitch DSBGA Package APPLICATIONS * * * Mobile Phones PDAs Portable Electronic Devices KEY SPECIFICATIONS * * * * * * * * Efficiency at 3.6V, 500mW into 8 Speaker: 87% (typ) Efficiency at 3.6V, 100mW into 8 Speaker: 80% (typ) Efficiency at 5V, 1W into 8 Speaker: 88% (typ) Quiescent Current, 3.6V Supply: 4.2mA (typ) Power Output at VDD = 5V RL = 4, THD 10%: 2.5W (typ) Power Output at VDD = 5V RL = 8, THD 10%: 1.5W (typ) Total Shutdown Power Supply Current: 0.01A (typ) Single Supply Range: 2.4V to 5.5V DESCRIPTION The LM48411 is a single supply, high efficiency, 2.5W/channel Class D audio amplifier. The LM48411 features TI's Enhanced Emissions Suppression (E2S) system, that features a unique patent-pending ultra low EMI, spread spectrum, PWM architecture, that significantly reduces RF emissions while preserving audio quality and efficiency. The E2S system improves battery life, reduces external component count, board area consumption, system cost, and simplifying design. The LM48411 is designed to meet the demands of mobile phones and other portable communication devices. Operating on a single 5V supply, it is capable of delivering 2.5W/channel of continuous output power to a 4 load with less than 10% THD+N. Its flexible power supply requirements allow operation from 2.4V to 5.5V. The wide band spread spectrum architecture of the LM48411 reduces EMIradiated emissions due to the modulator frequency. The LM48411 features high efficiency compared to a conventional Class AB amplifier. The E2S system includes an advanced, patent-pending edge rate control (ERC) architecture that further reduce emissions by minimizing the high frequency component of the device output, while maintaining high quality audio reproduction and high efficiency ( = 87% at VDD = 3.6V, PO = 500mW). Four gain options are pin selectable through GAIN0 and GAIN1 pins. The LM48411 features a low-power consumption shutdown mode. Shutdown may be enabled by driving the Shutdown pin to a logic low (GND). Output short circuit protection prevents the device from being damaged during fault conditions. Superior click and pop suppression eliminates audible transients on power up/down and during shutdown. Independent left/right shutdown control maximizes power savings in mixed mono/stereo applications. 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2007-2013, Texas Instruments Incorporated LM48411 SNAS399G - SEPTEMBER 2007 - REVISED MAY 2013 www.ti.com LM48411 RF Emissions 50.0 FCC Class B Limit AMPLITUDE (dBPV/m) 45.0 40.0 35.0 30.0 LM48411TL Output Spectrum 25.0 20.0 15.0 10.0 30.0 80.0 120.0 160.0 200.0 240.0 280.0 FREQUENCY (MHz) Figure 1. RF Emissions -- 3in cable Typical Application 2.4V to 5.5V CS2 CS1 VDD AUDIO INPUT PVDD Ci INR+ OUTRA GAIN/ MODULATOR Ci H-BRIDGE INR- OUTRB SDR GAIN0 OSCILLATOR GAIN1 SDL AUDIO INPUT Ci INL+ OUTLA GAIN/ MODULATOR Ci H-BRIDGE INL- OUTLB GND PGND Figure 2. Typical Audio Amplifier Application Circuit 2 Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LM48411 LM48411 www.ti.com SNAS399G - SEPTEMBER 2007 - REVISED MAY 2013 Connection Diagram 4 OUTRB OUTRA AVDD INR+ 3 PGND AGND G0 INR- 2 SDL SDR G1 INL- 1 OUTLB OUTLA PVDD INL+ C D A B Figure 3. DSBGA - Top View See YZR0016 Package PIN DESCRIPTIONS Bump Name A1 OUTLB Function Left Channel output B A2 SDL A3 PGND Left channel active low shutdown Power GND A4 OUTRB Right channel output B B1 OUTLA Left channel output A B2 SDR B3 AGND Ground Right channel output A Right channel active low shutdown B4 OUTRA C1 PVDD C2 G1 Gain setting input 1 C3 G0 Gain setting input 0 C4 AVDD Power supply D1 INL+ Non-inverting left channel input D2 INL- Inverting left channel input D3 INR- Inverting right channel input D4 INR+ Non-inverting right channel input Power VDD These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LM48411 3 LM48411 SNAS399G - SEPTEMBER 2007 - REVISED MAY 2013 www.ti.com Absolute Maximum Ratings (1) (2) (3) Supply Voltage (1) 6.0V -65C to +150C Storage Temperature VDD + 0.3V V GND - 0.3V Voltage at Any Input Pin Power Dissipation (4) ESD Rating, all other pins Internally Limited (5) 2.0kV ESD Rating (6) 200V Junction Temperature (TJMAX) Thermal Resistance 150C JA (DSBGA) Soldering Information (1) (2) (3) (4) (5) (6) 63.6C/W See SNVA009 "microSMD Wafers Level Chip Scale Package." "Absolute Maximum Ratings" indicate limits beyond which damage to the device may occur, including inoperability and degradation of device reliability and/or performance. Functional operation of the device and/or non-degradation at the Absolute Absolute Maximum Ratings or other conditions beyond those indicated in the Recommended Operating Conditions is not implied. The Recommended Operating Conditions indicate conditions at which the device is functional and the device should not be operated beyond such conditions. All voltages are measured with respect to the ground pin, unless otherwise specified The Electrical Characteristics tables list ensured specifications under the listed Recommended Operating Conditions except as otherwise modified or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only and are not ensured. If Military/Aerospace specified devices are required, please contact the TI Sales Office/ Distributors for availability and specifications. The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX, JA, and the ambient temperature, TA. The maximum allowable power dissipation is PDMAX = (TJMAX - TA) / JA or the number given in Absolute Maximum Ratings, whichever is lower. For the LMxxxxx, see Power Derating curves for additional information. Human body model, applicable std. JESD22-A114C. Machine model, applicable std. JESD22-A115-A. Operating Ratings (1) (2) Temperature Range TMIN TA TMAX -40C TA 85C 2.4V VDD 5.5V Supply Voltage (1) (2) 4 "Absolute Maximum Ratings" indicate limits beyond which damage to the device may occur, including inoperability and degradation of device reliability and/or performance. Functional operation of the device and/or non-degradation at the Absolute Absolute Maximum Ratings or other conditions beyond those indicated in the Recommended Operating Conditions is not implied. The Recommended Operating Conditions indicate conditions at which the device is functional and the device should not be operated beyond such conditions. All voltages are measured with respect to the ground pin, unless otherwise specified The Electrical Characteristics tables list ensured specifications under the listed Recommended Operating Conditions except as otherwise modified or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only and are not ensured. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LM48411 LM48411 www.ti.com SNAS399G - SEPTEMBER 2007 - REVISED MAY 2013 Electrical Characteristics The following specifications apply for AV = 6dB, RL = 15H+8, f = 1kHz, unless otherwise specified. Limits apply for TA = 25C. VDD = 3.6V. Symbol |VOS| IDD Parameter Differential Output Offset Voltage Quiescent Power Supply Current Conditions VI = 0V, AV = 2V/V, VDD = 2.4V to 5.0V LM48411 Typical (1) 5 5.1 7.5 mA (max) 4.2 6.0 mA (max) VIN = 0V, No Load, VDD = 2.4V 3.0 4.5 mA (max) VIN = 0V, RL = 8, VDD = 5.0V 5.2 mA VIN = 0V, RL = 8, VDD = 3.6V 4.2 mA VIN = 0V, RL = 8, VDD = 2.4V 3.0 VSDR = VSDL= GND 0.01 VSDIH Shutdown voltage input high VSDIL Shutdown voltage input low RIN TWU (1) (2) (3) Input Resistance Wake Up Time mV VIN = 0V, No Load, VDD = 3.6V Shutdown Current (3) Gain Units (Limits) VIN = 0V, No Load, VDD = 5.0V ISD AV Limit (2) (3) mA 1.0 A (max) For SDR, SDL 1.4 V (min) For SDR, SDL 0.4 V (max) GAIN0, GAIN1 = GND RL = 6 60.5 dB GAIN0 = VDD, GAIN1 = GND RL = 12 120.5 dB GAIN0 = GND, GAIN1 = VDD RL = 18 180.5 dB GAIN0, GAIN1 = VDD RL = 24 240.5 dB AV = 6dB 56 k AV = 12dB 37.5 k AV = 18dB 22.5 k AV = 24dB 12.5 k VSDR/SDL = 0.4V 4.2 ms Typical values represent most likely parametric norms at TA = +25C, and at the Recommended Operation Conditions at the time of product characterization and are not specified. Datasheet min/max specification limits are not specified by test or statistical analysis. Shutdown current is measured in a normal room environment. Exposure to direct sunlight will increase ISD by a maximum of 2A. The Shutdown pin should be driven as close as possible to GND for minimal shutdown current and to VDD for the best THD performance in PLAY mode. See the Application Information section under SHUTDOWN FUNCTION for more information. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LM48411 5 LM48411 SNAS399G - SEPTEMBER 2007 - REVISED MAY 2013 www.ti.com Electrical Characteristics (continued) The following specifications apply for AV = 6dB, RL = 15H+8, f = 1kHz, unless otherwise specified. Limits apply for TA = 25C. VDD = 3.6V. Symbol Parameter Conditions LM48411 Typical (1) Limit (2) (3) Units (Limits) RL = 15H + 4 + 15H THD = 10% (max) f = 1kHz, 22kHz BW VDD = 5V 2.5 W VDD = 3.6V 1.2 W VDD = 2.5V 530 mW VDD = 5V 2 W VDD = 3.6V 1 W VDD = 2.5V 430 mW RL = 15H + 4 + 15H THD = 1% (max) f = 1kHz, 22kHz BW PO Output Power RL = 15H + 8 + 15H THD = 10% (max) f = 1kHz, 22kHz BW VDD = 5V 1.5 W VDD = 3.6V 760 mW VDD = 2.5V 330 mW VDD = 5V 1.25 W VDD = 3.6V 615 mW VDD = 2.5V 270 mW PO = 500mW, f = 1kHz, RL = 8 0.05 % PO = 300mW, f = 1kHz, RL = 8 RL = 15H + 8 + 15H THD = 1% (max) f = 1kHz, 22kHz BW THD+N PSRR Total Harmonic Distortion + Noise Power Supply Rejection Ratio (Input Referred) 0.03 % VRipple = 200mVPP Sine, fRipple = 217Hz, VDD = 3.6, 5V Inputs to AC GND, CI = 2F 78 dB VRipple = 200mVPP Sine, fRipple = 1kHz, VDD = 3.6, 5V Inputs to AC GND, CI = 2F 77 dB SNR Signal to Noise Ratio VDD = 5V, PO = 1WRMS 96 dB OUT Output Noise (Input Referred) VDD = 3.6V, A Weighted 22 VRMS CMRR Common Mode Rejection Ratio (Input Referred) VDD = 3.6V, VRipple = 1VPP Sine fRipple = 217Hz 64 dB Efficiency VDD = 5V, POUT = 1W RL = 8 88 % Xtalk Crosstalk PO = 500mW, f = kHz 84 dB 6 Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LM48411 LM48411 www.ti.com SNAS399G - SEPTEMBER 2007 - REVISED MAY 2013 Typical Performance Characteristics The performance graphs were taken using the Audio Precision AUX-0025 Switching Amplifier measurement Filter in series with the LC filter on the demo board. THD+N vs Frequency VDD = 3.6V, RL = 8, PO = 250mW/channel AV = 6dB 10 10 1 1 THD+N (%) THD+N (%) THD+N vs Frequency VDD = 2.5V, RL = 8, PO = 100mW/channel AV = 6dB 0.1 0.01 0.01 0.001 20 0.1 100 1k 0.001 20 10k 20k 100 Figure 5. THD+N vs Frequency VDD = 5.0V, RL = 8, PO = 375mW/channel AV = 6dB THD+N vs Frequency VDD = 2.5V, RL = 4, PO = 100mW/channel AV = 6dB 10 10 1 1 THD+N (%) THD+N (%) 10k 20k Figure 4. 0.1 0.001 20 0.1 0.01 0.01 100 1k 0.001 20 10k 20k 100 FREQUENCY (Hz) 1k 10k 20k FREQUENCY (Hz) Figure 6. Figure 7. THD+N vs Frequency VDD = 3.6V, RL = 4, PO = 250mW/channel AV = 6dB THD+N vs Frequency VDD = 5.0V, RL = 4, PO = 375mW/channel AV = 6dB 10 10 1 1 THD+N (%) THD+N (%) 1k FREQUENCY (Hz) FREQUENCY (Hz) 0.1 0.01 0.01 0.001 20 0.1 100 1k 10k 20k FREQUENCY (Hz) 0.001 20 100 1k 10k 20k FREQUENCY (Hz) Figure 8. Figure 9. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LM48411 7 LM48411 SNAS399G - SEPTEMBER 2007 - REVISED MAY 2013 www.ti.com Typical Performance Characteristics (continued) The performance graphs were taken using the Audio Precision AUX-0025 Switching Amplifier measurement Filter in series with the LC filter on the demo board. THD+N vs Output Power VDD = 2.5V, RL = 8, AV = 24dB 10 10 1 1 THD+N (%) THD+N (%) THD+N vs Output Power VDD = 2.5V, RL = 8, AV = 6dB 0.1 0.1 0.01 0.01 0.001 10m 100m 0.001 10m 1 Figure 11. THD+N vs Output Power VDD = 3.6V, RL = 8, AV = 6dB THD+N vs Output Power VDD = 3.6V, RL = 8, AV = 24dB 10 10 1 1 THD+N (%) THD+N (%) Figure 10. 0.1 0.01 0.001 10m 0.1 0.01 100m 0.001 10m 1 OUTPUT POWER (W) 1 OUTPUT POWER (W) Figure 13. THD+N vs Output Power VDD = 5V, RL = 8, AV = 6dB THD+N vs Output Power VDD = 5V, RL = 8, AV = 24dB 10 THD+N (%) 0.1 0.1 0.01 0.01 0.001 10m 100m Figure 12. 10 THD+N (%) 1 OUTPUT POWER (W) OUTPUT POWER (W) 100m 1 2 0.001 10m 100m 1 2 OUTPUT POWER (W) OUTPUT POWER (W) Figure 14. 8 100m Figure 15. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LM48411 LM48411 www.ti.com SNAS399G - SEPTEMBER 2007 - REVISED MAY 2013 Typical Performance Characteristics (continued) The performance graphs were taken using the Audio Precision AUX-0025 Switching Amplifier measurement Filter in series with the LC filter on the demo board. THD+N vs Output Power VDD = 2.5V, RL = 4, AV = 24dB 10 10 1 1 THD+N (%) THD+N (%) THD+N vs Output Power VDD = 2.5V, RL = 4, AV = 6dB 0.1 0.01 0.1 0.01 0.001 10m 100m 0.001 10m 1 OUTPUT POWER (W) Figure 17. THD+N vs Output Power VDD = 3.6V, RL = 4, AV = 6dB THD+N vs Output Power VDD = 3.6V, RL = 4, AV = 24dB 10 10 1 1 0.1 0.01 0.1 0.01 0.001 10m 1 100m 0.001 10m 2 OUTPUT POWER (W) 1 100m 2 OUTPUT POWER (W) Figure 18. Figure 19. THD+N vs Output Power VDD = 5.0V, RL = 4, AV = 6dB THD+N vs Output Power VDD = 5.0V, RL = 4, AV = 24dB 10 10 1 1 THD+N (%) THD+N (%) 1 Figure 16. THD+N (%) THD+N (%) OUTPUT POWER (W) 100m 0.1 0.01 0.001 10m 0.1 0.01 100m 1 2 3 OUTPUT POWER (W) 0.001 10m 100m 1 2 3 OUTPUT POWER (W) Figure 20. Figure 21. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LM48411 9 LM48411 SNAS399G - SEPTEMBER 2007 - REVISED MAY 2013 www.ti.com Typical Performance Characteristics (continued) The performance graphs were taken using the Audio Precision AUX-0025 Switching Amplifier measurement Filter in series with the LC filter on the demo board. PSRR vs Frequency VDD = 3.6V, RL = 8 CMRR vs Frequency VDD = 3.6V, RL = 8 0 0 -10 -10 -20 -20 -30 CMRR (dB) PSRR (dB) -30 -40 -50 -40 -50 -60 -60 -70 -70 -80 -90 -80 -90 20 10k 20k 100 1k FREQUENCY (Hz) 100 200 1k 2k 10k 20k FREQUENCY (Hz) Figure 22. Figure 23. Quiescent Current vs Power Supply RL = Output Power vs Supply Voltage RL = 4, f = 1kHz 3000 5 2500 OUTPUT POWER (mW) 6 4 QCURR (mA) -100 20 3 2 1 2000 THD+N=10% 1500 1000 THD+N=1% 500 0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 0 2.5 POWER SUPPLY (V) 3.0 3.5 4.0 4.5 5.0 5.5 SUPPLY VOLTAGE (V) Figure 24. Figure 25. Output Power vs Supply Voltage RL = 8, f = 1kHz 100 2000 Efficiency vs Output Power RL = 4 90 1000 EFFCIENCY (%) OUTPUT POWER (mW) 80 1500 THD+N=10% THD+N=1% VDD = 5.0V 70 VDD = 3.6V 60 VDD = 2.5V 50 40 30 20 500 10 0 0 0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 0.5 1.0 1.5 2.0 2.5 OUTPUT POWER (W) SUPPLY VOLTAGE (V) Figure 26. 10 Figure 27. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LM48411 LM48411 www.ti.com SNAS399G - SEPTEMBER 2007 - REVISED MAY 2013 Typical Performance Characteristics (continued) The performance graphs were taken using the Audio Precision AUX-0025 Switching Amplifier measurement Filter in series with the LC filter on the demo board. 100 Efficiency vs Output Power RL = 8 Crosstalk vs Frequency VDD = 3.6V, RL = 8 0 90 -10 VDD = 5.0V 70 -20 VDD = 3.6V 60 -30 CROSSTALK (dB) EFFCIENCY (%) 80 VDD = 2.5V 50 40 30 20 -40 -50 -60 -70 10 -80 0 0 0.2 0.4 0.6 0.8 1.0 -90 1.2 -100 20 OUTPUT POWER (W) 100 200 1k 2k 10k 20k FREQUENCY (Hz) Figure 28. Figure 29. Power Dissipation vs Output Power RL = 4 Power Dissipation vs Output Power RL = 8 1.40 0.50 0.45 1.00 0.80 0.60 VDD = 5.0V VDD = 2.5V 0.40 POWER DISSIPATION (W) POWER DISSIPATION (w) 1.20 0.20 0.5 1.0 1.5 2.0 2.5 VDD = 5.0V 0.35 0.30 0.25 0.20 0.15 VDD = 3.6V 0.10 0.05 VDD = 3.6V 0.00 0.0 0.40 3.0 3.5 4.0 0.00 0.0 VDD = 2.5V 1.0 2.0 3.0 4.0 5.0 OUTPUT POWER (W) OUTPUT POWER (W) Figure 30. Figure 31. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LM48411 11 LM48411 SNAS399G - SEPTEMBER 2007 - REVISED MAY 2013 www.ti.com External Components Description (Figure 2) Components Functional Description 1. CS Supply bypass capacitor which provides power supply filtering. Refer to the Power Supply Bypassing section for information concerning proper placement and selection of the supply bypass capacitor. 2. CI Input AC coupling capacitor which blocks the DC voltage at the amplifier's input terminals. APPLICATION INFORMATION GENERAL AMPLIFIER FUNCTION The LM48411 features a filterless modulation scheme. The differential outputs of the device switch at 300kHz from VDD to GND. When there is no input signal applied, the two outputs (VO1 and VO2) switch with a 50% duty cycle, with both outputs in phase. Because the outputs of the LM48411 are differential, the two signals cancel each other. This results in no net voltage across the speaker, thus there is no load current during an idle state, conserving power. With an input signal applied, the duty cycle (pulse width) of the LM48411 outputs changes. For increasing output voltages, the duty cycle of VO1 increases, while the duty cycle of VO2 decreases. For decreasing output voltages, the converse occurs, the duty cycle of VO2 increases while the duty cycle of VO1 decreases. The difference between the two pulse widths yields the differential output voltage. SPREAD SPECTRUM MODULATION The LM48411 features a fitlerless spread spectrum modulation scheme that eliminates the need for output filters, ferrite beads or chokes. The switching frequency varies by 30% about a 300kHz center frequency, reducing the wideband spectral contend, improving EMI emissions radiated by the speaker and associated cables and traces. Where a fixed frequency class D exhibits large amounts of spectral energy at multiples of the switching frequency, the spread spectrum architecture of the LM48411 spreads that energy over a larger bandwidth. The cycle-to-cycle variation of the switching period does not affect the audio reproduction of efficiency. ENHANCED EMISSIONS SUPPRESSION SYSTEM (E2S) The LM48411 features TI's patent-pending E2S system that reduces EMI, while maintaining high quality audio reproduction and efficiency. The E2S system features a synchronizable oscillator with selectable spread spectrum, and advanced edge rate control (ERC). The LM48411 ERC greatly reduces the high frequency components of the output square waves by controlling the output rise and fall times, slowing the transitions to reduce RF emissions, while maximizing THD+N and efficiency performance. POWER DISSIPATION AND EFFICIENCY In general terms, efficiency is considered to be the ratio of useful work output divided by the total energy required to produce it with the difference being the power dissipated, typically, in the IC. The key here is "useful" work. For audio systems, the energy delivered in the audible bands is considered useful including the distortion products of the input signal. Sub-sonic (DC) and super-sonic components (>22kHz) are not useful. The difference between the power flowing from the power supply and the audio band power being transduced is dissipated in the LM48411 and in the transducer load. The amount of power dissipation in the LM48411 is very low. This is because the ON resistance of the switches used to form the output waveforms is typically less than 0.25. This leaves only the transducer load as a potential "sink" for the small excess of input power over audio band output power. The LM48411 dissipates only a fraction of the excess power requiring no additional PCB area or copper plane to act as a heat sink. DIFFERENTIAL AMPLIFIER EXPLANATION As logic supply voltages continue to shrink, designers are increasingly turning to differential analog signal handling to preserve signal to noise ratios with restricted voltage swing. The LM48411 is a fully differential amplifier that features differential input and output stages. A differential amplifier amplifies the difference between the two input signals. Traditional audio power amplifiers have typically offered only single-ended inputs resulting in a 6dB reduction in signal to noise ratio relative to differential inputs. The LM48411 also offers the possibility of 12 Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LM48411 LM48411 www.ti.com SNAS399G - SEPTEMBER 2007 - REVISED MAY 2013 DC input coupling which eliminates the two external AC coupling, DC blocking capacitors. The LM48411 can be used, however, as a single ended input amplifier while still retaining it's fully differential benefits. In fact, completely unrelated signals may be placed on the input pins. The LM48411 simply amplifies the difference between the signals. A major benefit of a differential amplifier is the improved common mode rejection ratio (CMRR) over single input amplifiers. The common-mode rejection characteristic of the differential amplifier reduces sensitivity to ground offset related noise injection, especially important in high noise applications. PCB LAYOUT CONSIDERATIONS As output power increases, interconnect resistance (PCB traces and wires) between the amplifier, load and power supply create a voltage drop. The voltage loss on the traces between the LM48411 and the load results is lower output power and decreased efficiency. Higher trace resistance between the supply and the LM48411 has the same effect as a poorly regulated supply, increased ripple on the supply line also reducing the peak output power. The effects of residual trace resistance increases as output current increases due to higher output power, decreased load impedance or both. To maintain the highest output voltage swing and corresponding peak output power, the PCB traces that connect the output pins to the load and the supply pins to the power supply should be as wide as possible to minimize trace resistance. The use of power and ground planes will give the best THD+N performance. While reducing trace resistance, the use of power planes also creates parasite capacitors that help to filter the power supply line. The inductive nature of the transducer load can also result in overshoot on one or both edges, clamped by the parasitic diodes to GND and VDD in each case. From an EMI standpoint, this is an aggressive waveform that can radiate or conduct to other components in the system and cause interference. It is essential to keep the power and output traces short and well shielded if possible. Use of ground planes, beads, and micro-strip layout techniques are all useful in preventing unwanted interference. As the distance from the LM48411 and the speaker increase, the amount of EMI radiation will increase since the output wires or traces acting as antenna become more efficient with length. What is acceptable EMI is highly application specific. Ferrite chip inductors placed close to the LM48411 may be needed to reduce EMI radiation. The value of the ferrite chip is very application specific. SHUTDOWN FUNCTION In order to reduce power consumption while not in use, the LM48411 contains shutdown circuitry that reduces current draw to less than 0.01A. The trigger point for shutdown is shown as a typical value in the Electrical Characteristics Tables and in the Shutdown Hysteresis Voltage graphs found in the Typical Performance Characteristics section. It is best to switch between ground and supply for minimum current usage while in the shutdown state. While the LM48411 may be disabled with shutdown voltages in between ground and supply, the idle current will be greater than the typical 0.01A value. The LM48411 has an internal resistor connected between GND and Shutdown pins. The purpose of this resistor is to eliminate any unwanted state changes when the Shutdown pin is floating. The LM48411 will enter the shutdown state when the Shutdown pin is left floating or if not floating, when the shutdown voltage has crossed the threshold. To minimize the supply current while in the shutdown state, the Shutdown pin should be driven to GND or left floating. If the Shutdown pin is not driven to GND, the amount of additional resistor current due to the internal shutdown resistor can be found by Equation 1 below. (VSD - GND) / 300k (1) With only a 0.5V difference, an additional 1.7A of current will be drawn while in the shutdown state. AUDIO AMPLIFIER POWER SUPPLY BYPASSING FILTERING Proper power supply bypassing is critical for low noise performance and high PSRR. Place the supply bypass capacitor as close to the device as possible. Typical applications employ a voltage regulator with 10F and 0.1F bypass capacitors that increase supply stability. These capacitors do not eliminate the need for bypassing of the LM48411 supply pins. A 1F capacitor is recommended. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LM48411 13 LM48411 SNAS399G - SEPTEMBER 2007 - REVISED MAY 2013 www.ti.com AUDIO AMPLIFIER INPUT CAPACITOR SELECTION Input capacitors may be required for some applications, or when the audio source is single-ended. Input capacitors block the DC component of the audio signal, eliminating any conflict between the DC component of the audio source and the bias voltage of the LM48411. The input capacitors create a high-pass filter with the input resistance Ri. The -3dB point of the high pass filter is found using Equation 2 below. f = 1 / 2RiCi (2) The values for Ri can be found in the EC table for each gain setting. The input capacitors can also be used to remove low frequency content from the audio signal. Small speakers cannot reproduce, and may even be damaged by low frequencies. High pass filtering the audio signal helps protect the speakers. When the LM48411 is using a single-ended source, power supply noise on the ground is seen as an input signal. Setting the high-pass filter point above the power supply noise frequencies, 217 Hz in a GSM phone, for example, filters out the noise such that it is not amplified and heard on the output. Capacitors with a tolerance of 10% or better are recommended for impedance matching and improved CMRR and PSRR. AUDIO AMPLIFIER GAIN SETTING The LM48411 features four internally configured gain settings. The device gain is selected through the two logic inputs, G0 and G1. The gain settings are as shown in the following table. LOGIC INPUT GAIN G1 G0 V/V 0 0 2 dB 6 0 1 4 12 1 0 8 18 1 1 16 24 Build of Materials Designator 14 Footprint Quantity C1, C2 Ceramic Capacitor 0.1F, 50V, 10% Description 805 2 C3 - C6 Tantalum Capacitors 1F 20V, 10%, Size A 1206 4 C11 Tantalum Capacitors 10F 20V, 10% Size B 1411 1 JP1-5, JP8-11 Jumper Header Vertical Mount 2X1 0.100 9 JP6, JP7 Jumper Header Vertical Mount 3x1 0.100 2 Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LM48411 LM48411 www.ti.com SNAS399G - SEPTEMBER 2007 - REVISED MAY 2013 Demonstration Board Schematic JP1 JP6 VDD C1 1 PF SDR 1 2 VDD INR- VDD PVDD INR+ INR+ C4 1 PF + 1 2 3 C3 1 PF JP2 INRJP8 GAIN0 SDR OUTRA SDR OUTRB 1 2 3 VDD GAIN0 GAIN1 GAIN1 SDL GAIN1 JP3 1 2 C5 1 PF INL+ INL- SDL 1 2 JP9 OUTLA SDL OUTLB 1 2 INL+ C6 1 PF + JP5 1 2 GAIN0 + JP7 C11 10 PF + VDD C2 1 PF + JP4 1 2 VDD 1 2 INL- GND PGND VDD Demonstration Board Layout Figure 32. Top Silkscreen Layer Figure 33. Top Layer Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LM48411 15 LM48411 SNAS399G - SEPTEMBER 2007 - REVISED MAY 2013 www.ti.com Figure 34. Mid 1 Layer Figure 35. Mid 2 Layer Figure 36. Bottom Layer 16 Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LM48411 LM48411 www.ti.com SNAS399G - SEPTEMBER 2007 - REVISED MAY 2013 REVISION HISTORY Rev Date 1.0 09/21/07 Initial release. Description 1.1 10/01/07 Fixed few typos. 1.2 11/30/07 Added the demo boards and BOM. 1.3 12/19/07 Edited the 16-bump DSBGA package diagram and the Pin Description table. 1.4 01/08/08 Edited the 16-bump DSBGA package diagram. 1.5 06/27/08 Text edits. 1.6 07/03/08 Text edits (under SHUTDOWN FUNCTION). Changes from Revision F (May 2013) to Revision G * Page Changed layout of National Data Sheet to TI format .......................................................................................................... 16 Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LM48411 17 PACKAGE OPTION ADDENDUM www.ti.com 2-May-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (C) Top-Side Markings (3) (4) LM48411TL/NOPB ACTIVE DSBGA YZR 16 250 Green (RoHS & no Sb/Br) SNAGCU Level-1-260C-UNLIM -40 to 85 GJ2 LM48411TLX/NOPB ACTIVE DSBGA YZR 16 3000 Green (RoHS & no Sb/Br) SNAGCU Level-1-260C-UNLIM -40 to 85 GJ2 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Top-Side Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 Samples PACKAGE MATERIALS INFORMATION www.ti.com 8-May-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) LM48411TL/NOPB DSBGA YZR 16 250 178.0 8.4 LM48411TLX/NOPB DSBGA YZR 16 3000 178.0 8.4 Pack Materials-Page 1 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 2.18 2.18 0.76 4.0 8.0 Q1 2.18 2.18 0.76 4.0 8.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 8-May-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM48411TL/NOPB DSBGA YZR LM48411TLX/NOPB DSBGA YZR 16 250 210.0 185.0 35.0 16 3000 210.0 185.0 35.0 Pack Materials-Page 2 MECHANICAL DATA YZR0016xxx D 0.6000.075 E TLA16XXX (Rev C) D: Max = 2.063 mm, Min =2.003 mm E: Max = 2.014 mm, Min =1.953 mm 4215051/A NOTES: A. All linear dimensions are in millimeters. Dimensioning and tolerancing per ASME Y14.5M-1994. B. This drawing is subject to change without notice. www.ti.com 12/12 IMPORTANT NOTICE Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. TI's published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and services. Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyers and others who are developing systems that incorporate TI products (collectively, "Designers") understand and agree that Designers remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products used in or for Designers' applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will thoroughly test such applications and the functionality of such TI products as used in such applications. TI's provision of technical, application or other design advice, quality characterization, reliability data or other services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, "TI Resources") are intended to assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any way, Designer (individually or, if Designer is acting on behalf of a company, Designer's company) agrees to use any particular TI Resource solely for this purpose and subject to the terms of this Notice. TI's provision of TI Resources does not expand or otherwise alter TI's applicable published warranties or warranty disclaimers for TI products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections, enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically described in the published documentation for a particular TI Resource. Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. TI RESOURCES ARE PROVIDED "AS IS" AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM, INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949 and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements. Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use. Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S. TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product). Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications and that proper product selection is at Designers' own risk. Designers are solely responsible for compliance with all legal and regulatory requirements in connection with such selection. Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer's noncompliance with the terms and provisions of this Notice. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2017, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: LM48411TL/NOPB LM48411TLBD LM48411TLX/NOPB