TSOP132.., TSOP134.., TSOP136..
www.vishay.com Vishay Semiconductors
Rev. 1.7, 16-Dec-2019 1Document Number: 82806
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
IR Receiver Modules for Remote Control Systems
ADDITIONAL RESOURCES
FEATURES
• Improved dark sensitivity
• Improved immunity against optical noise
• Improved immunity against Wi-Fi noise
• Low supply current
• Photo detector and preamplifier in one package
• Internal filter for PCM frequency
• Supply voltage: 2.5 V to 5.5 V
• Insensitive to supply voltage ripple and noise
• Material categorization: for definitions of
compliance please see www.vishay.com/doc?99912
MECHANICAL DATA
Pinning for TSOP13...:
1 = OUT, 2 = GND, 3 = VS
DESCRIPTION
The TSOP13... series devices are the latest generation miniaturized IR receiver modules for infrared remote control systems.
This series provides improvements in sensitivity to remote control signals in dark ambient as well as in sensitivity in the presence
of optical disturbances e.g. from CFLs. The robustness against spurious pulses originating from Wi-Fi signals has been
enhanced.
The devices contain a PIN diode and a preamplifier assembled on a lead frame. The epoxy package contains an IR filter. The
demodulated output signal can be directly connected to a microprocessor for decoding.
The TSOP132.., TSOP134.., and TSOP136.. series devices are designed to receive long burst codes (10 or more carrier cycles
per burst). The third digit designates the AGC level (AGC2, AGC4, or AGC6) and the last two digits designate the band-pass
frequency (see table below). The higher the AGC, the better noise is suppressed, but the lower the code compatibility. AGC2
provides basic noise suppression, AGC4 provides enhanced noise suppression and AGC6 provides maximized noise
suppression. Generally, we advise to select the highest AGC that satisfactorily receives the desired remote code.
These components have not been qualified to automotive specifications.
Note
• 30 kHz and 33 kHz only available on written request
23051
3
3
3
D
D
D
3
D
3D Models
PARTS TABLE
AGC BASIC NOISE SUPPRESSION
(AGC2)
ENHANCED NOISE SUPPRESSION
(AGC4)
MAXIMIZED NOISE SUPPRESSION
(AGC6)
Carrier
frequency
30 kHz TSOP13230 TSOP13430 TSOP13630
33 kHz TSOP13233 TSOP13433 TSOP13633
36 kHz TSOP13236 TSOP13436 (2)(5)(7) TSOP13636 (6)
38 kHz TSOP13238 TSOP13438 (3)(4)(10)(11) TSOP13638
40 kHz TSOP13240 (12) TSOP13440 TSOP13640
56 kHz TSOP13256 (1) TSOP13456 (9) TSOP13656 (8)
Package Minimold
Pinning 1 = OUT, 2 = GND, 3 = VS
Dimensions (mm) 5.4 W x 6.35 H x 4.9 D
Mounting Leaded
Application Remote control
Best choice for (1) Cisco (2) MCIR (3) Mitsubishi (4) NEC (5) Panasonic (6) RC-5 (7) RC-6
(8) RCA (9) r-step (10) Sejin 4PPM (11) Sharp (12) Sony
TSOP132.., TSOP134.., TSOP136..
www.vishay.com Vishay Semiconductors
Rev. 1.7, 16-Dec-2019 2Document Number: 82806
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
BLOCK DIAGRAM APPLICATION CIRCUIT
Note
• Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability
30 kΩ
2
3
1
Demo-
pass
AGCInput
PIN
Band
dulator
Control circuit
16833-13
C1
IR receiver
GND
Circuit
μC
R1
+ VS
GND
Transmitter
with
TSALxxxx VS
VO
17170-11
OUT
R1 and C1 recommended to reduce supply ripple for VS < 2.8 V
ABSOLUTE MAXIMUM RATINGS
PARAMETER TEST CONDITION SYMBOL VALUE UNIT
Supply voltage VS-0.3 to +6 V
Supply current IS3mA
Output voltage VO-0.3 to (VS + 0.3) V
Output current IO5mA
Junction temperature Tj100 °C
Storage temperature range Tstg -25 to +85 °C
Operating temperature range Tamb -25 to +85 °C
Power consumption Tamb ≤ 85 °C Ptot 10 mW
Soldering temperature t ≤ 10 s, 1 mm from case Tsd 260 °C
ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT
Supply current Ev = 0, VS = 3.3 V ISD 0.55 0.70 0.90 mA
Ev = 40 klx, sunlight ISH -0.80- mA
Supply voltage VS2.5 - 5.5 V
Transmission distance Ev = 0, test signal see Fig. 1,
IR diode TSAL6200, IF = 50 mA d-30-m
Output voltage low IOSL = 0.5 mA, Ee = 0.7 mW/m2,
test signal see Fig. 1 VOSL - - 100 mV
Minimum irradiance
Pulse width tolerance:
tpi - 3.5/f0 < tpo < tpi + 3.5/f0,
test signal see Fig. 1
Ee min. - 0.08 0.15 mW/m2
Maximum irradiance tpi - 3.5/f0 < tpo < tpi + 3.5/f0,
test signal see Fig. 1 Ee max. 30 - - W/m2
Directivity Angle of half transmission
distance ϕ1/2 -± 45- °
TSOP132.., TSOP134.., TSOP136..
www.vishay.com Vishay Semiconductors
Rev. 1.7, 16-Dec-2019 3Document Number: 82806
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
Fig. 1 - Output Delay and Pulse-Width
Fig. 2 - Pulse-Width vs. Irradiance in Dark Ambient
Fig. 3 - Test Signal
Fig. 4 - Pulse-Width vs. Irradiance in Dark Ambient
Fig. 5 - Frequency Dependence of Responsivity
Fig. 6 - Sensitivity in Bright Ambient
Ee
T
tpi (1)
t
VO
VOH
VOL
t
Optical Test Signal
(IR diode TSAL6200, IF = 0.1 A, 30 pulses, f = f0, t = 10 ms)
Output Signal
td (2) tpo (3)
(2) AGC4: 8/f0 < td < 14/f0
AGC2, AGC 6:
14/f0 < td < 20/f0
(3) tpi - 3.5/f0 < tpo < tpi + 3.5/f0
16110-15
(1) AGC4: tpi ≥ 10/f0, AGC2, AGC6: tpi ≥ 19/f0
10
100
1000
10000
0.50
0.60
0.70
0.80
0.90
1.00
0.1 10 1000
Axis Title
1st line
2nd line
2nd line
tpo - Output Pulse Width (ms)
Ee- Irradiance (mW/m2)
Output pulse width
Input burst length
λ= 950 nm,
optical test signal, Fig. 1
E
e
t
V
O
V
OH
V
OL
t
600 µs 600 µs
t = 60 ms
t
on
t
off
94 8134
Optical Test Signal
Output Signal, (see Fig. 4)
10
100
1000
10000
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.1 1 10 100 1000 10 000
Axis Title
1st line
2nd line
2nd line
ton, toff - Output Pulse Width (ms)
Ee- Irradiance (mW/m2)
ton
toff
λ= 950nm,
optical test signal, Fig. 3
10
100
1000
10000
0
0.2
0.4
0.6
0.8
1.0
1.2
0.7 0.9 1.1 1.3
Axis Title
1st line
2nd line
2nd line
Ee min./Ee- Relative Responsivity
f/f0- Relative Frequency
f = f
0
±5 %
10
100
1000
10000
0
1
2
3
0.01 0.1 1 10 100
Axis Title
1st line
2nd line
2nd line
Ee min. - Threshold Irradiance (mW/m2)
Ee- Ambient DC Irradiance (W/m2)
Correlation with ambient light sources:
10 W/m
2
= 1.4 klx (std. ilum. A, T = 2855 K)
10 W/m
2
= 8.2 klx (daylight, T = 5900 K)
Wavelength of ambient
illumination: λ = 950 nm
TSOP132.., TSOP134.., TSOP136..
www.vishay.com Vishay Semiconductors
Rev. 1.7, 16-Dec-2019 4Document Number: 82806
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Fig. 7 - Sensitivity vs. Supply Voltage Disturbances
Fig. 8 - Max. Envelope Duty Cycle vs. Burst Length
Fig. 9 - Sensitivity vs. Ambient Temperature
Fig. 10 - Relative Spectral Sensitivity vs. Wavelength
Fig. 11 - Directivity
Fig. 12 - Sensitivity vs. Supply Voltage
10
100
1000
10000
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
1101001000
Axis Title
1st line
2nd line
2nd line
Ee min. - Threshold Irradiance (mW/m2)
∆VS RMS - AC Voltage on DC Supply Voltage (mV)
f = 100 Hz
f = 10 kHz
f = 30 kHz
f = f0
10
100
1000
10000
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
0 20406080100120140
Axis Title
1st line
2nd line
2nd line
Maximum Envelope Duty Cycle
Burst Length (Number of Cycles/Burst)
TSOP134..
TSOP136..
f = 38 kHz, E
e
= 2 mW/m
2
TSOP132..
10
100
1000
10000
0
0.05
0.1
0.15
0.2
-30 -10 10 30 50 70 90
Axis Title
1st line
2nd line
2nd line
Ee min. - Threshold Irradiance (mW/m2)
Tamb - Ambient Temperature (°C)
10
100
1000
10000
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
750 850 950 1050 1150
Axis Title
1st line
2nd line
2nd line
S(λ)rel. - Relative Spectral Sensitivity
λ - Wavelength (nm)
Axis Title
2nd line
2nd line
2nd line
2nd line
drel. - Relative Transmission Distance
1.0
0.9
0.7
0.8
30°
50°
40°
80°
0.6 0.4 0.200.40.2 0.6
20°10°0°
60°
70°
10
100
1000
10000
0
0.05
0.1
0.15
0.2
1.5 2.5 3.5 4.5 5.5
Axis Title
1st line
2nd line
2nd line
Ee min. - Threshold Irradiance (mW/m2)
VS- Supply Voltage (V)
TSOP132.., TSOP134.., TSOP136..
www.vishay.com Vishay Semiconductors
Rev. 1.7, 16-Dec-2019 5Document Number: 82806
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
SUITABLE DATA FORMAT
This series is designed to suppress spurious output pulses
due to noise or disturbance signals. The devices can
distinguish data signals from noise due to differences in
frequency, burst length, and envelope duty cycle. The data
signal should be close to the device’s band-pass center
frequency (e.g. 38 kHz) and fulfill the conditions in the table
below.
When a data signal presented to the device in the
presence of a disturbance, the sensitivity of the receiver is
automatically reduced by the AGC to insure that no spurious
pulses are present at the receiver’s output. Some examples
which are suppressed are:
• DC light (e.g. from tungsten bulbs sunlight)
• Continuous signals at any frequency
• Strongly or weakly modulated patterns from fluorescent
lamps with electronic ballasts (see Fig. 13 or Fig. 14)
• 2.4 GHz and 5 GHz Wi-Fi
Fig. 13 - IR Disturbance from Fluorescent Lamp
With Low Modulation
Fig. 14 - IR Disturbance from Fluorescent Lamp
With High Modulation
Note
• For data formats with short bursts please see the datasheet for TSOP131.., TSOP133.., TSOP135..
16920
10
100
1000
10000
0
1
2
3
4
5
6
7
0 5 10 15 20
Axis Title
1st line
2nd line
2nd line
IR Signal Amplitude
Time (ms)
16921
10
100
1000
10000
-60
-40
-20
0
20
40
0 5 10 15 20
Axis Title
1st line
2nd line
2nd line
IR Signal Amplitude
Time (ms)
TSOP132.. TSOP134.. TSOP136..
Minimum burst length 19 cycles/burst 10 cycles/burst 19 cycles/burst
After each burst of length
a minimum gap time is required of
19 to 85 cycles
≥ 19 cycles
10 to 40 cycles
≥ 12 cycles
19 to 50 cycles
≥ 19 cycles
For bursts greater than
a minimum gap time in the data stream is needed of
85 cycles
> 6 x burst length
40 cycles
> 10 x burst length
50 cycles
> 10 x burst length
Maximum number of continuous short bursts/second 800 1300 800
RC-5 code Yes Preferred Preferred
RC-6 code Yes Preferred Yes
NEC code Yes Preferred Yes
r-step code Yes Preferred Yes
Sony code Preferred No No
RCA 56 kHz code Yes Yes Preferred
Suppression of interference from fluorescent lamps Fig. 13 Fig. 13 and Fig. 14 Fig. 13 and Fig. 14
TSOP132.., TSOP134.., TSOP136..
www.vishay.com Vishay Semiconductors
Rev. 1.7, 16-Dec-2019 6Document Number: 82806
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
PACKAGE DIMENSIONS in millimeters
Marking area
123
Cavity number
R2.5
R2.5
2.25
5
(3 x)
0.3 ± 0.1
(3 x) 0.6 ± 0.1
2.54 nom.
2.54 nom.
6.35
15.2 ± 0.3
0.95
(3 x) 0.85 max.
(5.05)
7.6
(0.95)
(1.1)
5.4
Drawing-No.: 6.550-5335.01-4
Issue: 2; 02.07.19
Technical drawings
according to DIN
specications
Not indicated tolerances ± 0.2
TSOP132.., TSOP134.., TSOP136..
www.vishay.com Vishay Semiconductors
Rev. 1.7, 16-Dec-2019 7Document Number: 82806
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
BULK PACKAGING
Standard shipping for minimold is in conductive plastic bags. The packing quantity is determined by weight and the number of
components per carton may vary by a maximum of ± 0.3 %.
ORDERING INFORMATION
Examples: TSOP13438
TSOP13456VI1
TSOP13438SS1F
For more information, see: www.vishay.com/doc?80076
PACKAGING QUANTITY
• 300 pieces per bag (each bag is individually boxed)
• 6 bags per carton
Legal Disclaimer Notice
www.vishay.com Vishay
Revision: 01-Jan-2021 1Document Number: 91000
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of
typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding
statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a
particular product with the properties described in the product specification is suitable for use in a particular application.
Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over
time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk.
Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for
such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document
or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
© 2021 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED
