Product specifi cations in this catalog are subject to change without notice.Request our product specifi cations before purchase and/or use. Please use our products based on the information contained in this catalog and product specifi cations.
PXE
Series
NPCAP
TM
-
CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
◆SPECIFICATIONS
(at 20℃, 120Hz)
(at 105℃)
(at 20℃ after 2 minutes)
(at 20℃, 120Hz)
(at 100kHz)
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Surge Voltage
Leakage Current
Dissipation Factor
(tanδ)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
Bias Humidity
Surge Voltage
Failure Rate
Items
-
55 to +105℃
2.5 to 16Vdc
±20% (M)
Rated voltage×1.15
Shall not exceed values shown in STANDARD RATINGS.
0.12 max.
Z(
-
25℃)/Z(+20℃)
≦
1.1 5
Z(
-
55℃)/Z(+20℃)
≦
1.25
The following specifications shall be satisfied when the capacitors are restored to 20℃ after the rated voltage is applied for 2,000 hours
at 105℃.
Appearance No significant damage
Capacitance change
≦±20% of the initial value
DF (tanδ)
≦
150% of the initial specified value
ESR
≦
150% of the initial specified value
Leakage current
≦
The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjecting them to the DC rated voltage at
60℃, 90 to 95% RH for 1,000 hours.
Appearance No significant damage
Capacitance change
≦±
20% of the initial value
DF (tanδ)
≦
150% of the initial specified value
ESR
≦
150% of the initial specified value
Leakage current
≦
The initial specified value
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105℃ for 30 seconds
through a protective resistor(R=1kΩ) and discharge for 5 minutes 30 seconds.
Appearance No significant damage
Capacitance change
≦±
20% of the initial value
DF (tanδ)≦
150% of the initial specified value
ESR
≦
150% of the initial specified value
Leakage current
≦
The initial specified value
0.5% per 1,000 hours maximum (Confidence level 60% at 105℃)
Characteristics
◆PART NUMBERING SYSTEM
◆DIMENSIONS [mm]
φ
D
±
0.5
B±
0.2
C±
0.2
L
±
0.3 (Note)
(Note) L
±
0.5 for HA0, HC0, JA0, JC0
0.3max. A
±
0.2
W
P
Size Code
E61
F61
F80
H70
H80
HA0
HC0
J80
JA0
JC0
φ
D
5
6.3
6.3
8
8
8
8
10
10
10
L
5.8
5.8
7.7
6.7
7.7
10.0
12.0
7.7
10.0
12.2
A
5.3
6.6
6.6
8.3
8.3
8.3
8.3
10.3
10.3
10.3
B
5.3
6.6
6.6
8.3
8.3
8.3
8.3
10.3
10.3
10.3
C
5.9
7.2
7.2
9.0
9.0
9.0
9.0
11.0
11.0
11.0
W
0.5 to 0.8
0.5 to 0.8
0.5 to 0.8
0.7 to 1.1
0.7 to 1.1
0.7 to 1.1
0.7 to 1.1
0.7 to 1.1
0.7 to 1.1
0.7 to 1.1
P
1.4
1.9
1.9
3.1
3.1
3.1
3.1
4.5
4.5
4.5
◆MARKING
E
49A
390
2.5
V
EX) 2.5V390µF
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105
℃
.
●Terminal Code : A
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 47μF:470,100μF:101)
Taping code
Terminal code
Voltage code (ex. 6.3V:6R3,10V:100)
Series code
Category
APX E A R A GM
1342 6 7 8 9 10 1312518171611 1514
Please refer to "Product code guide (conductive polymer type)"
Lower ESR
PXE
Lower ESR
PXA
PXF
(1/2)
Surface Mount
●Super low ESR, impedance and high heat resistance have been obtained by using
conductive polymer as electrolyte.
(ESR and rated ripple current values are improved from PXA series.)
●Rated voltage range : 2.5 to 16Vdc, Capacitance range : 33 to 2,700µF
●Suitable for DC-DC converters, voltage regulators and decoupling applications used on
computer motherboards etc.
●RoHS Compliant
●Halogen Free
CAT. No. E1001M