MY4F-AC220/240 - Omron - Product.Network

■Designed small, 2- and 3-pole types

break 5 A loads and 4-pole type, 3 A load

■High reliability, long life

■Ultra-high sensitivity with quick response

■High vibration/shock resistance

■3- and 4-pole types have an arc barrier

■UL and CSA approved

■Withstands dielectric strength of 2,000 V

■Relays with high-capacity, LED indicator,

diode surge suppression, push-to-test

button, or RC circuit are available

■Changes due to aging are negligible

because of use of special magnetic mate-

rials, thus ensuring long continuous hold-

ing time

■Little change in characteristics such as

contact follow, contact pressure, etc.,

throughout long life

Gener al Purpose Rela y MY

Ordering Information

To Order: Select the part number and add the desired coil voltage rating (e.g., MY4-

DC6

Part number

Single contact Bifurcated contact

Standard Upper Lower Standard Upper Lower

Contact bracket mounting mounting bracket mounting mounting

Type Terminal form Construction mounting bracket bracket mounting bracket bracket

Standard Plug-in/solder DPDT Unsealed MY2 MY2F MY2S MY2Z MY2ZF MY2ZS

3PDT MY3 MY3F MY3S — — —

4PDT MY4 MY4F MY4S MY4Z MY4ZF MY4ZS

PCB DPDT MY2-02 — — MY2Z-02 — —

3PDT MY3-02 —————

4PDT MY4-02 — — MY2Z-02 — —

Plug-in/solder 4PDT Sealed MYQ4 — — MYQ4Z — —

PCB 4PDT MYQ4-02 — — MYQ4Z-02 — —

Plug-in/solder 4PDT Hermetically MY4H — — MY4ZH — —

PCB 4PDT Sealed MY4H-0 — — MY4ZH-0 — —

Note: 1. For SEV approved type, order the following: MY4-

-DC6. (Lloyd's Register approval. See “Approvals” section.)

2. To order connecting sockets and mounting tracks, see “Accessories” section.

3. AgCdO contacts are also available (MY2E, MY3E, MY4E). Contact your OMRON sales representative for details.

MY MY

Ordering information (continued)

■ACCESSORIES

Connecting Sockets

To Order: Select the appropriate part numbers for sockets, clips, and mounting tracks (if required) from the available types char t.

Available T ypes

Track mounted sockets

Relay hold-down clip

Relay Socket* Standard RC circuit Mounting track

DPDT PYF08A-E PYC-A1 Y92-H3 PFP-100N/PFP-50N &

3PDT PYF11A PFP-M or PFP-100N2

4PDT PYF14A-E PFP-S (Optional spacer)

* Track mounted socket can be used as a front connecting socket.

Part number

Single contact Bifurcated contact

Standard Upper Lower Standard Upper Lower

Contact bracket mounting mounting bracket mounting mounting

Type Terminal form Construction mounting bracket bracket mounting bracket bracket

LED indicator Plug-in/solder DPDT MY2N — — MY2ZN — —

3PDT MY3N — — — — —

4PDT MY4N — — MY4ZN — —

High-capacity DPDT w/o LED MY2-Y — — — — —

indicator

LED indicator

MY2N-Y — — — — —

Diode surge DPDT MY2-D — — MY2Z-D — —

suppression* 3PDT MY3-D — — — — —

4PDT MY4-D — — MY4Z-D — —

LED indicator DPDT MY2N-D2 — —

MY2ZN-D2

——

and diode surge 3PDT MY3N-D2 — — — — —

suppression* 4PDT MY4N-D2 — — MY4ZN-D2 — —

RC circuit** DPDT w/o LED MY2-CR — — MY2Z-CR — —

3PDT indicator MY3-CR — — — — —

4PDT MY4-CR — — MY4Z-CR — —

DPDT LED indicator

MY2N-CR — — — — —

4PDT MY4N-CR — — — — —

Push-to-test DPDT MY214 — — MY2Z12 — —

button 4PDT MY414 — — MY4Z12 — —

LED indicator DPDT MY214N — — MY2Z12N — —

and RC circuit 4PDT MY414N — — MY4Z12N — —

Note: 1. For SEV approved type, order as the following: MY4-

-DC6. (Lloyd's Register approval. See “Approvals” section.)

2. To order connecting sockets and mounting tracks, see “Accessories” section.

3. AgCdO contacts are also available. Contact your OMRON sales representative for details.

4. * DC coils only

** AC coils only

Type Terminal Contact form Part number

Latching Plug-in DPDT MY2K-US

PC board MY2K-02-US

MY MY

Solder

Wire wrap

terminal terminal Relay hold-down clip Socket Mounting Plate

Relay socket socket Standard

Push-to-test

RC circuit Mtg. plate 1 18 36

DPDT PY08 PY08QN PYC-P PYC-P2 PYC-1 PYC-S PYP-1 PYP-18 PYP-36

3PDT PY11 PY11QN

4PDT PY14 PY14QN

Back connecting sockets

Note: Types PYP-18, PTP-12 and PTP-10 may be cut to any desired length.

PC terminal Relay hold-down clip

Relay socket Standard Push-to-test RC circuit

DPDT PY08-02 PYC-P PYC-P2 PYC-1

3PDT PY11-02

4PDT PY14-02

Specifications

DPDT, 3PDT 4DPT High-capacity

Resistive load Inductive load Resistive load Inductive load Resistive load Inductive load

(p.f. = 1) (p.f. = 0.4) (p.f. = 1) (p.f. = 0.4) (p.f. = 1) (p.f. = 0.4)

Load (L/R = 7 ms) (L/R = 7 ms) (L/R = 7 ms)

Rated load 5 A at 220 VAC 2 A at 220 VAC 3 A at 220 VAC 0.8 A at 220 VAC 7 A 220 VAC 3.5 A 220 VAC

5 A at 24 VDC 2 A at 24 VDC 3 A at 24 VDC 1.5 A at 24 VDC 7 A 24 VDC 3.5 A 24 VDC

Contact material Ag Ag (Au Flash) AgCdO

Carry current 5 A 3 A 1 A 3 A 7 A

Max. operating 250 VAC

voltage 125 VDC

Max. operating 5 A 1 A 3 A 7 A

current

Max. switching 1,100 VA 440 VA 660 VA 176 VA 1,540 V A 770 VA

capacity 120 W 48 W 72 W 36 W 168 W 84 W

Min. permissib le Standard type: 1 mA, 5 VDC Standard and high sensitivity types: 100 µA, 1 VDC

1 mA, 1 VDC

load (see note) Bifurcated type: 100 µA, 1 VDC

■CONTACT DATA

Non-latching – Unsealed

Sealed, 4PDT Hermetically sealed, 4DPT

Resistive load Inductive load Resistive load Inductive load

(p.f. = 1) (p.f. = 0.4) (p.f. = 1) (p.f. = 0.4)

Load (L/R = 7 ms) (L/R = 7 ms)

Rated load 1 A at 220 VAC 0.5 A at 220 VAC 3 A at 110 VAC 0.8 A at 110 VAC

1 A at 24 VDC 0.5 A at 24 VDC 3 A at 24 VDC 1.5 A at 24 VDC

Contact material Ag (Au Flash)

Carry current 1 A 3 A

Max. operating 250 VAC 125 VAC

voltage 125 VDC 125 VDC

Max. operating 1 A 3 A

current

Max. switching 220 V A 110 VA 330 VA 88 VA

capacity 24 W 12 W 72 W 36 W

Min. permissible Standard and high sensitivity types: 1 mA, 1 VDC

load (see note) Bifurcated type: 100 µA, 1 VDC

Non-latching – Sealed/Hermetically sealed

Note: P level: λ60 = 0.1 x 10-6/operation

MY MY

Rated Rated current (mA) Pick-up Dropout Maximum Power consumption

voltage Set coil

Reset coil

Coil resistance (Ω) voltage voltage voltage (V A, W)

(V) 50 Hz 60 Hz 50/60 Hz Set coil Reset coil (% of rated voltage) Set coil Reset coil

6 146 142 68 13 32 80% max. 80% max. 110% max. Approx. Approx.

12 57 56 39 72 130 0.60 to 0.90 0.20 to 0.50

24 27.40 26.40 18.60 320 550

50 14 13.40 3.50 1,400 3,000

120 15.80 5.60 3.50 8,300 3,000

Latching – AC

Coil inductance

Coil (ref. value) (H) Pick-up Dropout Maximum Power

Rated Rated current (mA) resistance Armature Armature voltage voltage voltage consumption

voltage (V) 50 Hz 60 Hz (Ω)OFF ON (% of rated voltage) (VA, W)

6 214.10 183 12.20 0.04 0.08 80% max. 30% min. 110% max. Approx.

12 106.50 91 46 0.17 0.33 1.00 to 1.20

24 53.80 46 180 0.69 1.30

50 25.70 22 788 3.22 5.66

100/110 11.70/12.90 10/11 3,750 14.54 24.60 Approx.

110/120 9.90/10.80 8.40/9.20 4,430 19.20 32.10 0.90 to 1.10

200/220 6.20/6.80 5.30/5.80 12,950 54.75 94.07

220/240 4.80/5.30 4.20/4.60 18,790 83.50 136.40

■COIL DATA

Non-latching – AC

Note: 1. The rated current and coil resistance are measured at a coil temperature of 23°C (73°F) with tolerances of +15%, -20% for

AC rated current, and ±15% for DC rated coil resistance.

2. The AC coil resistance and inductance are reference values at 60 Hz.

3. The performance characteristics are measured at a coil temperature of 23°C (73°F).

4. Because the coil is designed for low power consumption, connect a bleeder (if necessary after confirming the leakage

current), when the coil is driven by an SCR.

5. For AC type latching coils, the rated current values are half-wave rectified current values measured with a DC ammeter.

Coil inductance

Coil (ref. value) (H) Pick-up Dropout Maximum Power

Rated resistance Armature Armature voltage voltage voltage consumption

voltage (V) Rated current (mA) (Ω)OFF ON (% of rated voltage) (VA, W)

6 150 40 0.17 0.33 80% max. 10% min. 110% max. Approx.

12 75 160 0.73 1.37 0.90

24 36.90 650 3.20 5.72

48 18.50 2,600 10.60 21.00

100/110 9.10/10 11,000 45.60 86.20

Non-latching – DC

Rated Rated current (mA) Pick-up Dropout Maximum Power consumption

voltage Set coil Reset coil Coil resistance (Ω) voltage voltage voltage (VA, W)

(V) 50/60 Hz 50/60 Hz Set coil Reset coil (% of rated voltage) Set coil Reset coil

6 230 100 26 60 80% max. 80% max. 110% max. Approx. Approx.

12 110 50 110 235 1.30 0.06

24 52 25 470 940

Latching – DC

MY MY

Contact resistance 50 mΩ max.

Operate time 20 ms max.

Release time 20 ms max.

Operating frequency Mechanically 18,000 operations/hour

Under rated load 1,800 operations/hour

Insulation resistance 100 MΩ min. (at 500 VDC)

Dielectric strength Single contact type Unsealed: 2,000 VAC, 50/60 Hz for 1 minute

1,000 VAC, 50/60 Hz for 1 minute between contacts of same polarity

Sealed: 1,500 VAC, 50/60 Hz for 1 minute

1,000 VAC, 50/60 Hz for 1 minute between contacts of same polarity

Hermetically sealed: 1,000 VAC, 50/60 Hz for 1 minute

700 VAC, 50/60 Hz for 1 minute between contacts of same polarity

Bifurcated contact type 1,500 VAC, 50/60 Hz for 1 minute

1,000 VAC, 50/60 Hz for 1 minute between non-continuous contacts

Vibration Mechanical durability 10 to 55 Hz, 1.00 mm (0.04 in) double amplitude

Malfunction durability 10 to 55 Hz, 1.00 mm (0.04 in) double amplitude

Shock Mechanical durability 1,000 m/s2 (approx. 100 G)

Malfunction durability 200 m/s2 (approx. 20 G)

Ambient temperature Operating Unsealed: -55° to 70°C (-67° to 158°F)

Sealed: -55° to 60°C (-67° to 140°F)

Hermetically sealed: 25° to 60°C (77° to 140°F)

Humidity 35% to 85% RH

Ser vice Life Mechanically Single contact type:

AC: 50 million operations min. (at operating frequency of 18,000 operations/hour)

DC: 100 million operations min. (at operating frequency of 18,000 operations/hour)

Mechanically Bifurcated contact type:

AC: 50 million operations min.

DC: 20 million operations min. (5 million operations for the sealed/hermetically

sealed types) (at operating frequency of 1,800 operations/hour)

Electrically See “Characteristic Data”

Weight Sealed/unsealed: Approx. 35 g (1.23 oz)

Hermetically sealed: Approx. 50 g (1.76 oz)

■CHARACTERISTICS

Non-latching

Note: Data shown are of initial value.

Contact resistance 50 mΩ max.

Operate time AC: 30 ms max.; DC: 15 ms max.

Release time AC: 30 ms max.; DC: 15 ms max.

Operating frequency Mechanically 18,000 operations/hour

Under rated load 1,800 operations/hour

Insulation resistance 100 MΩ min. (at 500 VDC)

Dielectric strength 1,500 VAC, 50/60 Hz for 1 minute

1,000 VAC, 50/60 Hz for 1 minute between contacts of same polarity, and between

set and reset coils

Vibration Mechanical durability 10 to 55 Hz, 1.00 mm (0.04 in) double amplitude

Malfunction durability 10 to 55 Hz, 1.00 mm (0.04 in) double amplitude

Shock Mechanical durability 1,000 m/s2 (approx. 100 G)

Malfunction durability 200 m/s2 (approx. 20 G)

Ambient temperature Operating -55° to 70°C (-67° to 158°F)

Humidity 45% to 85% RH

Ser vice Life Mechanically 100 million operations min. (at operating frequency of 18,000 operations/hour)

Electrically See “Characteristic Data”

Weight Approx. 30 g (1.06 oz)

Latching

MY MY

■CHARACTERISTIC DATA

Maximum switching capacity – Non-latching

MY2, MY3 MY4 MY4(Z)H MYQ4(Z)H

Electrical service life

MY2, MY3 (Resistive load) MY2, MY3 (Inductive load) MY4 (Resistive load) MY4 (Inductive load)

Rated operating current (A)

Rated operating voltage (V) Rated operating voltage (V) Rated operating voltage (V) Rated operating voltage (V)

Service life (operations x 106)

Rated operating current (A) Rated operating current (A) Rated operating current (A) Rated operating current (A)

MY4H MY4Z (Resistive load) MY4Z (Inductive load) MYQ4

Service life (operations x 106)

Rated operating current (A) Rated operating current (A) Rated operating current (A) Rated operating current (A)

MY2-Y(Resistive load) MY2-Y (Inductive load)

Service life (operations x 106)

Rated operating current (A) Rated operating current (A)

MY MY

MY2 MY3 MY4

Dimensions

Unit: mm (inch)

■RELAYS

Maximum switching capacity – Latching Electrical service life

MY2K(-02)-US MY2K(-02)-US

(Resistive load) (Inductive load)

Rated operating current (A)

Service life (operations x 106)

Rated operating voltage (V) Rated operating current (A) Rated operating current (A)

MY■■-02 Mounting holes

MY■■F Mounting holes

Note: The abov e dimensioned dr awing shows the 4-pole type. The dimensions of the 2- and 3-pole types are identical to the 4-pole type.

MY MY

MY(Z)H MY4(Z)H-0

Unit: mm (inch)

■RELAYS (continued)

MY■■-5 Mounting holes Terminal arrangement

(Bottom view)

MY2 MY3

MY4, MYQ4(Z), MY4(Z)H, MY4H-0

MYQ4(Z) MYQ4(Z)-02

Note: The abov e dimensioned dr awing shows the 4-pole type. The dimensions of the 2- and

3-pole types are identical the 4-pole type.

MY2K-US MY2K-02-US Mounting holes

(Bottom view)

MY MY

■ACCESSORIES

Unit: mm (inch)

Track mounted sockets (UL File No. E87929) (CSA Report No. LR46088)

PYF08A-E Terminal arrangement/ PYF11A Terminal arrang ement/

mounting holes mounting holes

(Top view) (Top view)

PYF14A-E Terminal arrangement/ Mounting height of

mounting holes relay with socket

(Top view)

Note: 1. UL/CSA does not apply to wire wrap (Q) type sockets.

2. Value in brackets is for MY■■CR.

Back connecting socket (UL File No. E87929) (CSA Report No. LR46088) – DPDT

PY08 PY08QN PY08-02

Back connecting socket (UL File No. E87929) (CSA Report No. LR46088) – 3PDT

PY11 PY11QN PY11-02

MY MY

■ACCESSORIES (continued)

Unit: mm (inch)

Back connecting socket (UL File No. E87929) (CSA Report No. LR46088) – 4PDT

PY14 PY14QN PY14-02

Terminal arrang ement (Bottom view) Panel cutout Mounting height of

relay with socket

Mounting holes

DPDT 3PDT 4PDT

Relay hold-down clip

PYC-A1 PYC-P PYC-S

for PYF■■A socket for PY■■ socket for relay mounting plates

Note: Value in brackets is for MY■■-CR.

DPDT 3DPT 4DPT

* For types wiith suffix - 02.

MY MY

Relay hold-down clip

PYC-P2 Y92-HC PYC-1

for test button self-contained type with PY■■A socket for RC circuit for RC circuit

PFP-100N/PFP-50N mounting track

PFP-100N2 mounting track

* This dimension is 14.99 mm (0.59 in) on both ends in the case of PFP-100N, but on one end in the case of PFP-50N.

** L = Length

PFP-50N ...............L = 497.84 mm (19.60 in)

PFP-100N ...............L = 990.60 mm (39.00 in)

PFP-100N2 ...............L = 990.60 mm (39.00 in)

*** A total of twelv e 24.89 x 4.57 mm (0.98 x 0.18 in) elliptic holes are provided, with six holes cut from each end of the trac k at a pitch

of 9.91 (0.39) between holes.

PFP-M end plate PFP-S spacer

MY MY

■ACCESSORIES (continued)

Unit: mm (inch)

Socket mounting plates [t=1.52 (.06)]

PYP-1 PYP-18 PYP-36

Number of socket specs.

Socket needed 1 18 36

PY08, PY11, PY11QN, PYP-1 PYP-18 PYP-36

PY14, PY4QN

■RELAY OPTIONS

LED Indicator

Specifications and dimensions same as the standard type

with the following exception. Because an LED indicator is

employed as the operation indicator, the rated current is

approximately 3.8 mA higher in the DC types and 0.5 to 5 mA

higher in the AC types than in the standard type.

Ambient operating temperature: -55° to 60°C (-67° to 140°F).

Green LED............ DC

Red LED ............... AC

Terminal arrang ement/Internal connections (Bottom view)

MY4N

DC coil rating type AC coil rating type

Note: 1. In MY2N and MY3N, only the contact circuit is different from the illustration below. The coil terminals 10 and 11 of MY3N

become (-) and (+), respectively.

2. Pay special attention to the polarities when using the DC type.

3. The AC coil-type is provided with a self-diagnostic function that detects a breakage in the coil.

RC Circuit

Specifications and dimensions same as the standard type with the

following exceptions.

The panel cutout dimensions are the same as those of the standard type.

However, the height is higher by 17.02 mm (0.67 in).

Note: 1. The above dimensioned drawing shows the 4-pole type. The dimensions of the 2- and 3-pole types are identical to the 4-

pole type.

2. Available on AC versions only.

3. Terminal arrangement/internal connections: MY2-Y is the same as the standard type; MY2N-Y is the same as the LED

indicator type.

Terminal arrang ement/

Internal connections

(Bottom view)

MY MY

Note: 1. Pay special attention to the polarities when using the DC type.

2. The release time is somewhat longer, but satisfies the standard specifications of 25 ms.

3. The reverse-breakdown voltage of the diode is 1,000 VDC.

4. Available on DC versions only.

Diode Surge Suppression

Specifications and dimensions same as the standard

type with the following exceptions.

Terminal arrangement/internal connections: MY2(N)-

D(2) is the same as the MY4(N)-D(2) with the exception

of the contact configuration.

Ambient operating temperature: -55° to 60°C (-67° to

140°F).

Characteristic Data

Without RC circuit With RC circuit

Push-to-test button

MY■■12 Mounting holes

When mounting the relay, use the connecting socket PYC-P2 shown

in “ACCESSORIES” section. The mounting hole dimensions shown

here are applicable to the relay with mounting stud.

Note: The dimension drawings show the 4-pole type. The dimensions of the 2- and 3-pole types are identical to the 4-pole type.

Terminal arrangement/Internal connections (Bottom view)

MY4-D MY4N-D2 MY4N-D2

6, 12, 24, 48 6, 12, 24, 48 VDC 100/110 VDC

100/110 VDC

Connecting sockets

Use the standard MY4 (4PDT) sockets with the terminal arrangements listed below.

Terminal arrangement/Internal connections (Bottom view)

AC DC

Note: 1. R is a resistor for ampere-turn compensation, and is incorporated in the relays rated at 50 VAC or above.

2. Pay attention to the polarity of the set and reset coils, as incorrect connection of positive and negative terminals will res ult in

malfunctioning of the relay.

MY MY

Type Contact form Coil ratings Contact ratings

MY■■DPDT 6 to 240 VAC 5 A, 120 VAC (Resistive)

6 to 120 VDC 5 A, 28 VDC (Resistive)

5 A, 240 VAC (Inductive)

3PDT 5 A, 28 VDC (Resistive)

5 A, 240 VAC (Resistive)

4PDT 3 A, 28 VDC (Resistive)

3 A, 120 VAC (Inductive)

1.5 A, 240 VAC (Inductive)

5 A, 240 VAC (Inductive, same polarity)

5 A, 28 VDC (Resistive, same polarity)

MY2K-■■DPDT 5 to 120 VAC 3 A, 240 VAC (Resistive)

5 to 48 VDC 3 A, 28 VDC (Resistive)

■APPROVALS

UL recognized type (File No. E41515)

Note: 1. The rated values approved by each of the safety standards (e.g., UL, CSA, VDE, and SEV) may be different from the

performance characteristics individually defined in this catalog.

2. In the interest of product improvement, specifications are subject to change.

Type Contact form Coil ratings Contact ratings

MY■■DPDT 6 to 240 VAC 5 A, 28 VDC (Resistive)

3PDT 6 to 120 VDC 5 A, 240 VAC (Inductive)

4PDT 3 A, 28 VDC (Resistive)

3 A, 240 VAC (Inductive)

5 A, 240 VAC (Inductive, same polarity)

5 A, 28 VDC (Resistive, same polarity)

MY2K-■■DPDT 5 to 120 VAC 3 A, 240 VAC (General purpose)

5 to 48 VDC 3 A, 30 VDC (Resistive)

CSA certified type (File No. LR31928)

Type Contact form Coil ratings Contact ratings

MY■■DPDT 6 to 240 VAC 2 A, 30 VDC (Inductive)

4PDT 6 to 120 VDC 2 A, 200 VAC (Inductive)

1.5 A, 30 VDC (Inductive)

0.8 A, 200 VAC (Inductive)

1.5 A, 115 VAC (Inductive)

LR (Lloyd's Register) approved type (File No. 563KOB-204524)

Type Contact form Coil ratings Contact ratings

MY■■-SV DPDT 6 to 240 VAC 5 A, 220 VAC (Resistive)

3PDT 6 to 110 VDC 5 A, 24 VDC (Resistive)

4PDT

SEV listed type (File No. D791/63 [2- & 4-pole], D791/91 [3-pole])

■HINTS ON CORRECT USE

When using the relay rated at 120 VAC at a supply voltage of

240 VAC, be sure to connect exter nal resistors Rs and Rr to

the relay.

Terms and Conditions of Sale

1. Offer; Acceptance. These terms and conditions (these "Terms") are deemed

part of all quotes, agreements, purchase orders, acknowledgments, price lists,

catalogs, manuals, brochures and other documents, whether electronic or in

writing, relating to the sale of products or services (collectively, the "Products")

by Omron Electronics LLC and its subsidiary companies (“Omron”). Omron

objects to any terms or conditions proposed in Buyer’s purchase order or other

documents which are inconsistent with, or in addition to, these Terms.

2. Prices; Payment Terms. All prices stated are current, subject to change with-

out notice by Omron. Omron reserves the right to increase or decrease prices

on any unshipped portions of outstanding orders. Payments for Products are

due net 30 days unless otherwise stated in the invoice.

3. Discounts. Cash discounts, if any, will apply only on the net amount of invoices

sent to Buyer after deducting transportation charges, taxes and duties, and will

be allowed only if (i) the invoice is paid according to Omron’s payment terms

and (ii) Buyer has no past due amounts.

4. Interest. Omron, at its option, may charge Buyer 1-1/2% interest per month or

the maximum legal rate, whichever is less, on any balance not paid within the

stated terms.

5. Orders. Omron will accept no order less than $200 net billing.

6. Governmental Approvals. Buyer shall be responsible for, and shall bear all

costs involved in, obtaining any government approvals required for the impor-

tation or sale of the Products.

7. Taxes. All taxes, duties and other governmental charges (other than general

real property and income taxes), including any interest or penalties thereon,

imposed directly or indirectly on Omron or required to be collected directly or

indirectly by Omron for the manufacture, production, sale, delivery, importa-

tion, consumption or use of the Products sold hereunder (including customs

duties and sales, excise, use, turnover and license taxes) shall be charged to

and remitted by Buyer to Omron.

8. Financial. If the financial position of Buyer at any time becomes unsatisfactory

to Omron, Omron reserves the right to stop shipments or require satisfactory

security or payment in advance. If Buyer fails to make payment or otherwise

comply with these Terms or any related agreement, Omron may (without liabil-

ity and in addition to other remedies) cancel any unshipped portion of Prod-

ucts sold hereunder and stop any Products in transit until Buyer pays all

amounts, including amounts payable hereunder, whether or not then due,

which are owing to it by Buyer. Buyer shall in any event remain liable for all

unpaid accounts.

9. Cancellation; Etc. Orders are not subject to rescheduling or cancellation

unless Buyer indemnifies Omron against all related costs or expenses.

10. Force Majeure. Omron shall not be liable for any delay or failure in delivery

resulting from causes beyond its control, including earthquakes, fires, floods,

strikes or other labor disputes, shortage of labor or materials, accidents to

machinery, acts of sabotage, riots, delay in or lack of transportation or the

requirements of any government authority.

11. Shipping; Delivery. Unless otherwise expressly agreed in writing by Omron:

a. Shipments shall be by a carrier selected by Omron; Omron will not drop ship

except in “break down” situations.

b. Such carrier shall act as the agent of Buyer and delivery to such carrier shall

constitute delivery to Buyer;

c. All sales and shipments of Products shall be FOB shipping point (unless oth-

erwise stated in writing by Omron), at which point title and risk of loss shall

pass from Omron to Buyer; provided that Omron shall retain a security inter-

est in the Products until the full purchase price is paid;

d. Delivery and shipping dates are estimates only; and

e. Omron will package Products as it deems proper for protection against nor-

mal handling and extra charges apply to special conditions.

12. Claims. Any claim by Buyer against Omron for shortage or damage to the

Products occurring before delivery to the carrier must be presented in writing

to Omron within 30 days of receipt of shipment and include the original trans-

portation bill signed by the carrier noting that the carrier received the Products

from Omron in the condition claimed.

13. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that the

Products will be free from defects in materials and workmanship for a period of

twelve months from the date of sale by Omron (or such other period expressed

in writing by Omron). Omron disclaims all other warranties, express or implied.

(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION,

EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABIL-

ITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS.

BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE

PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR

INTENDED USE. Omron further disclaims all warranties and responsibility of

any type for claims or expenses based on infringement by the Products or oth-

erwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obli-

gation hereunder shall be, at Omron’s election, to (i) replace (in the form

originally shipped with Buyer responsible for labor charges for removal or

replacement thereof) the non-complying Product, (ii) repair the non-complying

Product, or (iii) repay or credit Buyer an amount equal to the purchase price of

the non-complying Product; provided that in no event shall Omron be responsi-

ble for warranty, repair, indemnity or any other claims or expenses regarding

the Products unless Omron’s analysis confirms that the Products were prop-

erly handled, stored, installed and maintained and not subject to contamina-

tion, abuse, misuse or inappropriate modification. Return of any Products by

Buyer must be approved in writing by Omron before shipment. Omron Compa-

nies shall not be liable for the suitability or unsuitability or the results from the

use of Products in combination with any electrical or electronic components,

circuits, system assemblies or any other materials or substances or environ-

ments. Any advice, recommendations or information given orally or in writing,

are not to be construed as an amendment or addition to the above warranty.

See http://www.omron247.com or contact your Omron representative for pub-

lished information.

14. Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLE

FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,

LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY

WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS

BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.

Further, in no event shall liability of Omron Companies exceed the individual

price of the Product on which liability is asserted.

15. Indemnities. Buyer shall indemnify and hold harmless Omron Companies and

their employees from and against all liabilities, losses, claims, costs and

expenses (including attorney's fees and expenses) related to any claim, inves-

tigation, litigation or proceeding (whether or not Omron is a party) which arises

or is alleged to arise from Buyer's acts or omissions under these Terms or in

any way with respect to the Products. Without limiting the foregoing, Buyer (at

its own expense) shall indemnify and hold harmless Omron and defend or set-

tle any action brought against such Companies to the extent based on a claim

that any Product made to Buyer specifications infringed intellectual property

rights of another party.

16. Property; Confidentiality. Any intellectual property in the Products is the exclu-

sive property of Omron Companies and Buyer shall not attempt to duplicate it

in any way without the written permission of Omron. Notwithstanding any

charges to Buyer for engineering or tooling, all engineering and tooling shall

remain the exclusive property of Omron. All information and materials supplied

by Omron to Buyer relating to the Products are confidential and proprietary,

and Buyer shall limit distribution thereof to its trusted employees and strictly

prevent disclosure to any third party.

17. Export Controls. Buyer shall comply with all applicable laws, regulations and

licenses regarding (i) export of products or information; (iii) sale of products to

“forbidden” or other proscribed persons; and (ii) disclosure to non-citizens of

regulated technology or information.

18. Miscellaneous. (a) Waiver. No failure or delay by Omron in exercising any right

and no course of dealing between Buyer and Omron shall operate as a waiver

of rights by Omron. (b) Assignment. Buyer may not assign its rights hereunder

without Omron's written consent. (c) Law. These Terms are governed by the

law of the jurisdiction of the home office of the Omron company from which

Buyer is purchasing the Products (without regard to conflict of law princi-

ples). (d) Amendment. These Terms constitute the entire agreement between

Buyer and Omron relating to the Products, and no provision may be changed

or waived unless in writing signed by the parties. (e) Severability

. If any provi-

sion hereof is rendered ineffective or invalid, such provision shall not invalidate

any other provision. (f) Setoff. Buyer shall have no right to set off any amounts

against the amount owing in respect of this invoice. (g) Definitions. As used

herein, “including” means “including without limitation”; and “Omron Compa-

nies” (or similar words) mean Omron Corporation and any direct or indirect

subsidiary or affiliate thereof.

Certain Precautions on Specifications and Use

1. Suitability of Use. Omron Companies shall not be responsible for conformity

with any standards, codes or regulations which apply to the combination of the

Product in the Buyer’s application or use of the Product. At Buyer’s request,

Omron will provide applicable third party certification documents identifying

ratings and limitations of use which apply to the Product. This information by

itself is not sufficient for a complete determination of the suitability of the Prod-

uct in combination with the end product, machine, system, or other application

or use. Buyer shall be solely responsible for determining appropriateness of

the particular Product with respect to Buyer’s application, product or system.

Buyer shall take application responsibility in all cases but the following is a

non-exhaustive list of applications for which particular attention must be given:

(i) Outdoor use, uses involving potential chemical contamination or electrical

interference, or conditions or uses not described in this document.

(ii) Use in consumer products or any use in significant quantities.

(iii) Energy control systems, combustion systems, railroad systems, aviation

systems, medical equipment, amusement machines, vehicles, safety equip-

ment, and installations subject to separate industry or government regulations.

(iv) Systems, machines and equipment that could present a risk to life or prop-

erty. Please know and observe all prohibitions of use applicable to this Prod-

uct.

NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS

RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT

ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO

ADDRESS THE RISKS, AND THAT THE OMRON’S PRODUCT IS PROP-

ERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE

OVERALL EQUIPMENT OR SYSTEM.

2. Programmable Products. Omron Companies shall not be responsible for the

user’s programming of a programmable Product, or any consequence thereof.

3. Performance Data. Data presented in Omron Company websites, catalogs

and other materials is provided as a guide for the user in determining suitabil-

ity and does not constitute a warranty. It may represent the result of Omron’s

test conditions, and the user must correlate it to actual application require-

ments. Actual performance is subject to the Omron’s Warranty and Limitations

of Liability.

4. Change in Specifications. Product specifications and accessories may be

changed at any time based on improvements and other reasons. It is our prac-

tice to change part numbers when published ratings or features are changed,

or when significant construction changes are made. However, some specifica-

tions of the Product may be changed without any notice. When in doubt, spe-

cial part numbers may be assigned to fix or establish key specifications for

your application. Please consult with your Omron’s representative at any time

to confirm actual specifications of purchased Product.

5. Errors and Omissions. Information presented by Omron Companies has been

checked and is believed to be accurate; however, no responsibility is assumed

for clerical, typographical or proofreading errors or omissions.

OMRON ELECTRONICS LLC •

THE AMERICAS HEADQUARTERS

Schaumburg, IL USA • 847.843.7900 • 800.556.6766 • www.omron247.com

OMRON CANADA, INC. • HEAD OFFICE

Toronto, ON, Canada • 416.286.6465 • 866.986.6766 •

www.omron247.com

OMRON ELETRÔNICA DO BRASIL LTDA • HEAD OFFICE

São Paulo, SP, Brasil • 55.11.2101.6300 • www.omron.com.br

OMRON ELECTRONICS MEXICO SA DE CV • HEAD OFFICE

Apodaca, N.L. • 52.811.156.99.10 • 001.800.556.6766 •

mela@omron.com

OMRON ARGENTINA • SALES OFFICE

Cono Sur • 54.11.4783.5300

OMRON CHILE • SALES OFFICE

Santiago • 56.9.9917.3920

OTHER OMRON LATIN AMERICA SALES

54.11.4783.5300

ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.

To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.

Note: This datasheet is provided as a guideline for selecting products. Do not use this document to operate the Unit.

Cat. No. DS_MY_GCRLY6 09/97 Specifica tions are subject to c hange witho ut notic e.