PRV6, PARV6 Vishay Sfernice Fully Sealed Potentiometers Cermet (PRV6) Conductive Plastic (PARV6) FEATURES * PRV6 high power rating 1.5 Watt at 70 C * PARV6 0.75 Watt at 70 C RoHS * CECC 41300 COMPLIANT * Military performances * Low cost * Fully sealed and panel sealed * Compatible RV6 (MIL R 94) * Mechanical life 50 000 cycles DIMENSIONS in millimeters PRV cermet PRV6 PARV conductive plastic PARV6 Terminal options available on all types Shafts and bushings: 6 - 61 - 62 5.08 (0.200") 2 (0.079") 5.08 (0.200") CIRCUIT DIAGRAM Locking shaft H option: 61H - 62H 61LCH - 62LCH Conic nut wrench 8 (3/16") 0.8 (0.031") a c (1) (3) b 5.08 (0.200") 0.8 (0.031") CW (2) 2.4 O 12.7 (1/2") O 3.17 (1/8") O 12.7 (1/2") 0.5 .4 ) 12 90" .4 (0 O 2.5 (0.098") 1.6 x 0.3 (0.063 x 0.012) 0.8 x 0.3 (0.031" x 0.12) (0.094") B O 6.35 (1/4") 32 Threads/inch Solder lugs (0.020") A PCB pins W option L C 2 (0.79") O 6.5 (0.256") 5 (0.200") 5.08 (0.200") Panel cutout VARIATION LAWS Vs % Ve 90 % B F Shaft Dia 4 mm: 6Q - 61Q - 61QH 50 % 5 L C Od=4 O 7.2 A O4 B 20 % L 10 % 75 50 4.3 25 15 Electrical travel 270 15 O 2.6 O D = M7 x 0.75 See ordering information for quotation Mechanical travel 300 0.8 TAPERS Tapers A - L - F - are measured between the wiper (2) and the ccw terminal (1). www.vishay.com 124 For technical questions, contact: sfer@vishay.com See also: Application notes Document Number: 51035 Revision: 29-Jun-06 PRV6, PARV6 Fully Sealed Potentiometers Cermet (PRV6) Conductive Plastic (PARV6) Vishay Sfernice ELECTRICAL SPECIFICATIONS Resistive Element Electrical Travel Resistance Range PRV6 cermet 270 15 20 to 10 M 470 to 1 M 20 % 10 % 5% 1.5 W 0.75 W 100 ppm/C 350 V Linear Law (A) Non Linear Laws (F-L) Standard On Request Linear Other Tapers Tolerance Power Rating at + 70 C Temperature Coefficient Limiting Element Voltage Contact Resist. Variation CRV End Resistance (Typical) Dielectric Strength Insulation Resistance (500 VDC) 2 % or 3 1 1750 VRMS (2000 VRMS on request) 106 M MECHANICAL SPECIFICATIONS or End Stop Torque max or Tightening Torque max or POWER RATING CHART 300 5 0.5 to 2 Ncm 0.7 to 3 oz.in. 35 Ncm 3 lb.in. 150 Ncm 13 lb.in PRV6 linear law 1.50 POWER IN WATT Mechanical Travel Operating Torque ENVIRONMENTAL SPECIFICATIONS Temperature Range Climatic Category Sealing PARV6 conductive plastic 270 15 1 k to 1 M 470 to 500 k ( 20 %) 20 % 10 % (1 k to100 k ) 0.75 W 0.4 W 1000 ppm/C 350 V PRV6 PARV6 - 55 C to + 125 C - 40 C to + 125 C 55/125/56 40/125/56 fully sealed container IP67 and panel sealed PARV6 linear law PRV6 non linear law 0.75 PARV6 non linear law 0.4 0 0 40 20 60 70 80 125 100 AMBIENT TEMPERATURE IN DEGREES CELSIUS PERFORMANCE CECC 41 300 and/or MIL R 94 TESTS Load Life Climatic Sequence Long Term Damp Heat Rapid Temperature Change Vibration Shock Rotational Life Document Number: 51035 Revision: 29-Jun-06 CONDITIONS TYPICAL VALUES AND DRIFTS RT (%) REQUIREMENTS RT R1-2 (%) R1-2 RT (%) RT R1-2 (%) R1-2 1000 h at rated power 90'/30' - temperature 70 C 10 % Phase A dry heat 100 C Phase B damp heat Phase C cold - 55 C Phase D damp heat 5 cycles 10 % 10 % 0.5 % 1% 10 % 10 % 0.5 % 1% 56 days CRV < 7 % Rn 1% CRV < 3 % Rn Insulation resist. > 100 M Insulation resist. > 104 M 5 cycles - 55 C at + 125 C 3% 0.5 % 10 g 55 to 2000 Hz 2 h each direction 2% 100 g 6 ms 20 shocks 2% 50 000 cycles 10 % no CUT > 0.1 ms 5 % 5% CRV < 7 % Rn For technical questions, contact: sfer@vishay.com See also: Application notes 0.1 % 0.1 % 3% 0.2 % 0.2 % CRV < 2 % Rn www.vishay.com 125 PRV6, PARV6 Fully Sealed Potentiometers Cermet (PRV6) Conductive Plastic (PARV6) Vishay Sfernice PANEL SEALING STANDARD RESISTANCE ELEMENT DATA PRV6 LINEAR LAW STANDARD RESISMAX. MAX. MAX. TANCE POWER WORKING WIPER VALUES AT 70 C VOLTAGE CUR. 20 50 W 1.5 100 200 500 1K 2K 5K 10K 20K 50K 100K 200K 500K 1M 2M 5M 10M 1.5 1.22 0.61 0.25 0.12 0.06 0.025 0.012 V 5.48 8.66 mA 274 173 12.2 17.3 27.4 38.7 54.8 86.6 122.5 173 274 350 350 350 350 350 350 350 122 87 55 38.7 27.4 17.3 12.2 8.26 5.65 3.5 1.75 0.7 0.35 0.17 0.07 0.035 PRV6 NON-LINEAR LAWS MAX. MAX. MAX. POWER WORKING WIPER AT 70 C VOLTAGE CUR. W V mA 0.75 0.61 0.25 TCR - 55 C + 125 C SHAFTS ppm/C 0 + 200 Shaft lengths are measured from the mounting face to the free end of the shaft. Special shafts are available if the customer supplies a drawing. The shaft slot is aligned to the wiper within 10. HARDWARE 27.4 19.3 12.2 8.7 6.1 3.9 2.74 1.75 0.7 27.3 38.2 61.2 87 122 194 273 350 350 0.75 Except for dia. 4 mm shaft, an O.ring is supplied with the potentiometer. This O.ring should be placed into the groove of the body and ensures the panel sealing. For dia. 4 mm shaft please see note "P" in ordering information. Nuts, washer and O.ring are separately supplied (not mounted on the potentiometer), in a small bag placed in the packaging. PRV6 100 LOCATING PEG Except for dia. 4 mm shaft, the potentiometers are delivered with 2 opposite locating pegs orientated at 45. These 2 pegs can be easily broken-off by the customer. On request, the orientation of the pegs can be at 30 instead of 45. Order Designation: PRV6 L (see ordering information) MARKING PACKAGING VISHAY trademark, series, style, ohmic value (in , k or M), tolerance in %, taper code, manufacturing date (4 digits: 2 for year, 2 for week), terminal 1. Carton box of 50, code: BO50 ORDERING INFORMATION PRV cermet PARV conductive plastic SERIES BUSHING DIA LENGTH D B Standard C = 9.5 no code Option C = 12.1 code S BODY LENGTH SHAFT DIA d 6 6.35 6.35 3 or 3.17 61 6.35 9.5 3 or 3.17 62 6.35 12.5 3 or 3.17 6Q 7 6.5 4 61Q 7 9.5 4 6QP 7 6.5 4 61QP 7 9.5 4 Solder Lugs no code PCB pins code W TERMINALS Code H not available for 6-6Q versions LOCKING SHAFT A: standard 45 no code A: option 30 code L not available for 6Q and 61Q versions See drawing LOCATING PEGS 22 to 10 M linear law - cermet 470 to 1 M non-linear laws From mounting face cermet DIA LENGTH 1 k to 1 M CODE d L linear law conductive 9.5 3.17 *CK plastic S 470 to 500 k 12.5 3.17 CM 6 L non linear laws 16 3.17 CD 61 O conductive plastic 22 3.17 CR 62 T 470 to 100 k 9.5 3 *K 61H T non linear laws 12.5 3 M 62H E conductive plastic 22 3 R D 9.5 4 E 6Q 12.5 4 F 61Q OHMIC VALUE 22 4 G 61QH * not available with 62H option Shaft dia 3.17 and 3 are standard panel sealed Shaft dia 4: please note "P" for panel sealed option 20 % standard 10 % optional 5 % optional (cermet only) STANDARD SHAFT LENGTH SHAFTS and BUSHINGS TOLERANCE A Linear L CW Log VARIATION LAW PRV S 61 W L H 10 k CM 20 % A 0 3 PACKAGING BO50 SAP PART NUMBERING GUIDELINES P R V 6 B B L STYLE PEG BUSHING See the end of this data book for conversion tables MODEL www.vishay.com 126 B B SHAFT X LEADS B 2 PACKAGING For technical questions, contact: sfer@vishay.com See also: Application notes 5 1 M A OHMIC VALUE/TOL/LAW OR SPECIAL Document Number: 51035 Revision: 29-Jun-06 Legal Disclaimer Notice Vishay Disclaimer All product specifications and data are subject to change without notice. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any information provided herein to the maximum extent permitted by law. The product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein, which apply to these products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 18-Jul-08 www.vishay.com 1