DATASHEET ISL21080 FN6934 Rev.5.00 Jun 23, 2014 300nA NanoPower Voltage References Features The ISL21080 analog voltage references feature low supply voltage operation at ultra-low 310nA typ, 1.5A max operating current. Additionally, the ISL21080 family features guaranteed initial accuracy as low as 0.2% and 50ppm/C temperature coefficient. * Reference output voltage . . . . . . . . 0.900V, 1.024V, 1.250V, 1.500V, 2.048V, 2.500V, 3.000V, 3.300V, 4.096V, 5.000V * Initial accuracy: These references are ideal for general purpose portable applications to extend battery life at lower cost. The ISL21080 is provided in the industry standard 3 Ld SOT-23 pinout. - The ISL21080 output voltages can be used as precision voltage sources for voltage monitors, control loops, standby voltages for low power states for DSP, FPGA, Datapath Controllers, microcontrollers and other core voltages: 0.9V, 1.024V, 1.25V, 1.5V, 2.048V, 2.5V, 3.0V, 3.3V, 4.096V and 5.0V. ISL21080-09 and -10 . . . . . . . . . . . . . . . . . . . . . . . . . ISL21080-12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ISL21080-15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ISL21080-20 and -25 . . . . . . . . . . . . . . . . . . . . . . . . . ISL21080-30, -33, -41, and -50 . . . . . . . . . . . . . . . . . 0.7% 0.6% 0.5% 0.3% 0.2% Special Note: Post-assembly x-ray inspection may lead to permanent changes in device output voltage and should be minimized or avoided. For further information, please see "Applications Information" on page 14 and AN1533, "X-Ray Effects on Intersil FGA References". * Input voltage range: - ISL21080-09 . . . . . . . . . . . . . . . . . . . . . . . . . . . - ISL21080-10, -12, -15, -20 and -25. . . . . . . . . - ISL21080-30 . . . . . . . . . . . . . . . . . . . . . . . . . . . - ISL21080-33 . . . . . . . . . . . . . . . . . . . . . . . . . . . - ISL21080-41. . . . . . . . . . . . . . . . . . . . . . . . . . . . - ISL21080-50 . . . . . . . . . . . . . . . . . . . . . . . . . . . Applications * Output voltage noise . . . . . . . . . . . . .30VP-P (0.1Hz to 10Hz) * Energy harvesting applications * Supply current . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5A (max) * Wireless sensor network applications * Tempco . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50ppm/C * Low power voltage sources for controllers, FPGA, ASICs or logic devices * Output current capability . . . . . . . . . . . . . . . . . . . . . . . . 7mA 2.0V to 5.5V 2.7V to 5.5V 3.2V to 5.5V 3.5V to 5.5V 4.5V to 8.0V 5.5V to 8.0V * Operating temperature range. . . . . . . . . . . . . -40C to +85C * Battery management/monitoring * Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Ld SOT-23 * Low power standby voltages * Pb-Free (RoHS compliant) * Portable Instrumentation Related Literature * Consumer/medical electronics * Wearable electronics * Lower cost industrial and instrumentation * See AN1494, "Reflow and PC Board Assembly Effects on Intersil FGA References" * Power regulation circuits * See AN1533, "X-Ray Effects on Intersil FGA References" * Control loops and compensation networks * See AN1761, "ISL21080XXEV1Z User's Guide" * LED/diode supply 500 UNIT 1 400 UNIT 2 IN (nA) 300 UNIT 3 200 100 0 2.7 2.9 3.1 3.3 3.5 3.7 3.9 4.1 4.3 4.5 4.7 4.9 5.1 5.3 5.5 VIN (V) FIGURE 1. IIN vs VIN, 3 UNITS FN6934 Rev.5.00 Jun 23, 2014 Page 1 of 21 ISL21080 Pin Configuration Pin Descriptions ISL21080 (3 LD SOT-23) TOP VIEW VIN 1 3 GND PIN NUMBER PIN NAME DESCRIPTION 1 VIN Input Voltage Connection. 2 VOUT Voltage Reference Output 3 GND Ground Connection VOUT 2 Ordering Information PART NUMBER (Notes 1, 2, 3) PART MARKING (Note 4) VOUT OPTION (V) GRADE (%) TEMP. RANGE (C) PACKAGE Tape & Reel (Pb-Free) PKG. DWG. # ISL21080DIH309Z-TK BCLA 0.9 0.7 -40 to +85 3 Ld SOT-23 P3.064 ISL21080DIH310Z-TK BCMA 1.024 0.7 -40 to +85 3 Ld SOT-23 P3.064 ISL21080DIH312Z-TK BCNA 1.25 0.6 -40 to +85 3 Ld SOT-23 P3.064 ISL21080CIH315Z-TK BCDA 1.5 0.5 -40 to +85 3 Ld SOT-23 P3.064 ISL21080CIH320Z-TK BCPA 2.048 0.3 -40 to +85 3 Ld SOT-23 P3.064 ISL21080CIH325Z-TK BCRA 2.5 0.3 -40 to +85 3 Ld SOT-23 P3.064 ISL21080CIH330Z-TK BCSA 3.0 0.2 -40 to +85 3 Ld SOT-23 P3.064 ISL21080CIH333Z-TK BCTA 3.3 0.2 -40 to +85 3 Ld SOT-23 P3.064 ISL21080CIH341Z-TK BCVA 4.096 0.2 -40 to +85 3 Ld SOT-23 P3.064 ISL21080CIH350Z-TK BCWA 5.0 0.2 -40 to +85 3 Ld SOT-23 P3.064 NOTES: 1. Please refer to TB347 for details on reel specifications. 2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 3. For Moisture Sensitivity Level (MSL), please see device information page for ISL21080. For more information on MSL please see techbrief TB363. 4. The part marking is located on the bottom of the part. FN6934 Rev.5.00 Jun 23, 2014 Page 2 of 21 ISL21080 Absolute Maximum Ratings Thermal Information Max Voltage VIN to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +6.5V VIN to GND (ISL21080-41 and 50 only) . . . . . . . . . . . . . . . -0.5V to +10V VOUT to GND (10s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to VOUT +1V VOUT to GND (10s) ISL21080-41 and 50 only . . . . . . . . . . . . . . . . . . . . . . -0.5V to +5.1V ESD Ratings Human Body Model (Tested to JESD22-A114) . . . . . . . . . . . . . . . . . . 5kV Machine Model (Tested to JESD22-A115) . . . . . . . . . . . . . . . . . . . . . 500V Charged Device Model (Tested to JESD22-C101) . . . . . . . . . . . . . . . . 2kV Latch Up (Tested per JESD-78B; Class 2, Level A) . . . . . . . . . . . . . . 100mA Thermal Resistance (Typical) JA (C/W) JC (C/W) 3 Lead SOT-23 (Notes 6, 7) . . . . . . . . . . . . . . 275 110 Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . .+107C Continuous Power Dissipation (TA = +85C) . . . . . . . . . . . . . . . . . . . 99mW Storage Temperature Range. . . . . . . . . . . . . . . . . . . . . . . .-65C to +150C Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see TB493 Recommended Operating Conditions Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40C to +85C Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7V to 5.5V Environmental Operating Conditions X-Ray Exposure (Note 5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10mRem CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. NOTES: 5. Measured with no filtering, distance of 10" from source, intensity set to 55kV and 70mA current, 30s duration. Other exposure levels should be analyzed for Output Voltage drift effects. See "Applications Information" on page 14. 6. JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details. 7. For JC, the "case temp" location is taken at the package top center. 8. Post-reflow drift for the ISL21080 devices will range from 100V to 1.0mV based on experimental results with devices on FR4 double sided boards. The design engineer must take this into account when considering the reference voltage after assembly. 9. Post-assembly x-ray inspection may also lead to permanent changes in device output voltage and should be minimized or avoided. Initial accuracy can change 10mV or more under extreme radiation. Most inspection equipment will not affect the FGA reference voltage, but if x-ray inspection is required, it is advisable to monitor the reference output voltage to verify excessive shift has not occurred. Electrical Specifications (ISL21080-09, VOUT = 0.9V) VIN = 3.0V, TA = -40C to +85C, IOUT = 0, unless otherwise specified. Boldface limits apply over the operating temperature range, -40C to +85C. PARAMETER DESCRIPTION VOUT Output Voltage VOA VOUT Accuracy @ TA = +25C (Notes 8, 9) TC VOUT Output Voltage Temperature Coefficient (Note 10) VIN Input Voltage Range IIN Supply Current VOUT /VIN Line Regulation VOUT/IOUT Load Regulation CONDITIONS MIN (Note 13) TYP MAX (Note 13) 0.9 -0.7 UNIT V +0.7 % 50 ppm/C 5.5 V 0.35 1.5 A 2V < VIN < 5.5V 30 350 V/V Sourcing: 0mA IOUT 10mA 6 100 V/mA Sinking: -10mA IOUT 0mA 23 350 V/mA 2.0 ISC Short Circuit Current TA = +25C, VOUT tied to GND 30 mA tR Turn-on Settling Time VOUT = 0.1% with no load 1 ms Ripple Rejection f = 120Hz -40 dB eN Output Voltage Noise 0.1Hz f 10Hz 40 VP-P VN Broadband Voltage Noise 10Hz f 1kHz 10 VRMS Noise Density f = 1kHz 1.1 V/Hz VOUT/TA Thermal Hysteresis (Note 11) TA = +125C 100 ppm VOUT/t Long Term Stability (Note 12) TA = +25C 60 ppm FN6934 Rev.5.00 Jun 23, 2014 Page 3 of 21 ISL21080 Electrical Specifications (ISL21080-10, VOUT = 1.024V) VIN = 3.0V, TA = -40C to +85C, IOUT = 0, unless otherwise specified. Boldface limits apply over the operating temperature range, -40C to +85C. PARAMETER DESCRIPTION VOUT Output Voltage VOA VOUT Accuracy @ TA = +25C (Notes 8, 9) TC VOUT Output Voltage Temperature Coefficient (Note 10) VIN Input Voltage Range CONDITIONS MIN (Note 13) TYP MAX (Note 13) 1.024 -0.7 2.7 UNIT V +0.7 % 50 ppm/C 5.5 V IIN Supply Current 0.31 1.5 A VOUT /VIN Line Regulation 2.7V < VIN < 5.5V 80 350 V/V VOUT/IOUT Load Regulation Sourcing: 0mA IOUT 7mA 25 100 V/mA Sinking: -7mA IOUT 0mA 50 350 V/mA ISC Short Circuit Current TA = +25C, VOUT tied to GND 50 mA tR Turn-on Settling Time VOUT = 0.1% with no load 4 ms Ripple Rejection f = 120Hz -40 dB eN Output Voltage Noise 0.1Hz f 10Hz 30 VP-P VN Broadband Voltage Noise 10Hz f 1kHz 52 VRMS Noise Density f = 1kHz 2.2 V/Hz VOUT/TA Thermal Hysteresis (Note 11) TA = +165C 100 ppm VOUT/t Long Term Stability (Note 12) TA = +25C 50 ppm Electrical Specifications (ISL21080-12, VOUT = 1.25V) VIN = 3.0V, TA = -40C to +85C, IOUT = 0, unless otherwise specified. Boldface limits apply over the operating temperature range, -40C to +85C. PARAMETER DESCRIPTION VOUT Output Voltage VOA VOUT Accuracy @ TA = +25C (Notes 8, 9) TC VOUT Output Voltage Temperature Coefficient (Note 10) VIN Input Voltage Range IIN Supply Current VOUT /VIN Line Regulation VOUT/IOUT Load Regulation CONDITIONS MIN (Note 13) TYP MAX (Note 13) 1.25 -0.6 UNIT V +0.6 % 50 ppm/C 5.5 V 0.31 1.5 A 2.7V < VIN < 5.5V 80 350 V/V Sourcing: 0mA IOUT 7mA 25 100 V/mA Sinking: -7mA IOUT 0mA 50 350 V/mA 2.7 ISC Short Circuit Current TA = +25C, VOUT tied to GND 50 mA tR Turn-on Settling Time VOUT = 0.1% with no load 4 ms Ripple Rejection f = 120Hz -40 dB eN Output Voltage Noise 0.1Hz f 10Hz 30 VP-P VN Broadband Voltage Noise 10Hz f 1kHz 52 VRMS Noise Density f = 1kHz 1.1 V/Hz VOUT/TA Thermal Hysteresis (Note 11) TA = +165C 100 ppm VOUT/t Long Term Stability (Note 12) TA = +25C 50 ppm FN6934 Rev.5.00 Jun 23, 2014 Page 4 of 21 ISL21080 Electrical Specifications (ISL21080-15, VOUT = 1.5V) VIN = 3.0V, TA = -40C to +85C, IOUT = 0, unless otherwise specified. Boldface limits apply over the operating temperature range, -40C to +85C. PARAMETER DESCRIPTION VOUT Output Voltage VOA VOUT Accuracy @ TA = +25C (Notes 8, 9) TC VOUT Output Voltage Temperature Coefficient (Note 10) VIN Input Voltage Range CONDITIONS MIN (Note 13) TYP MAX (Note 13) 1.5 -0.5 2.7 UNIT V +0.5 % 50 ppm/C 5.5 V IIN Supply Current 0.31 1.5 A VOUT /VIN Line Regulation 2.7V < VIN < 5.5V 80 350 V/V VOUT/IOUT Load Regulation Sourcing: 0mA IOUT 7mA 10 100 V/mA Sinking: -7mA IOUT 0mA 50 350 V/mA ISC Short Circuit Current TA = +25C, VOUT tied to GND 50 mA tR Turn-on Settling Time VOUT = 0.1% with no load 4 ms Ripple Rejection f = 120Hz -40 dB eN Output Voltage Noise 0.1Hz f 10Hz 30 VP-P VN Broadband Voltage Noise 10Hz f 1kHz 52 VRMS Noise Density f = 1kHz 1.1 V/Hz VOUT/TA Thermal Hysteresis (Note 11) TA = +165C 100 ppm VOUT/t Long Term Stability (Note 12) TA = +25C 50 ppm Electrical Specifications d (ISL21080-20, VOUT = 2.048V) VIN = 3.0V, TA = -40C to +85C, IOUT = 0, unless otherwise specified. Boldface limits apply over the operating temperature range, -40C to +85C. PARAMETER DESCRIPTION VOUT Output Voltage VOA VOUT Accuracy @ TA = +25C (Notes 8, 9) TC VOUT Output Voltage Temperature Coefficient (Note 10) VIN Input Voltage Range IIN Supply Current VOUT /VIN Line Regulation VOUT/IOUT Load Regulation CONDITIONS MIN (Note 13) TYP MAX (Note 13) 2.048 -0.3 UNIT V +0.3 % 50 ppm/C 5.5 V 0.31 1.5 A 2.7V < VIN < 5.5V 80 350 V/V Sourcing: 0mA IOUT 7mA 25 100 V/mA Sinking: -7mA IOUT 0mA 50 350 V/mA 2.7 ISC Short Circuit Current TA = +25C, VOUT tied to GND 50 mA tR Turn-on Settling Time VOUT = 0.1% with no load 4 ms Ripple Rejection f = 120Hz -40 dB eN Output Voltage Noise 0.1Hz f 10Hz 30 VP-P VN Broadband Voltage Noise 10Hz f 1kHz 52 VRMS Noise Density f = 1kHz 1.1 V/Hz VOUT/TA Thermal Hysteresis (Note 11) TA = +165C 100 ppm VOUT/t Long Term Stability (Note 12) TA = +25C 50 ppm FN6934 Rev.5.00 Jun 23, 2014 Page 5 of 21 ISL21080 Electrical Specifications (ISL21080-25, VOUT = 2.5V) VIN = 3.0V, TA = -40C to +85C, IOUT = 0, unless otherwise specified. Boldface limits apply over the operating temperature range, -40C to +85C. PARAMETER DESCRIPTION CONDITIONS MIN (Note 13) MAX (Note 13) UNIT +0.3 % 50 ppm/C 5.5 V 0.31 1.5 A TYP VOUT Output Voltage VOA VOUT Accuracy @ TA = +25C (Notes 8, 9) TC VOUT Output Voltage Temperature Coefficient (Note 10) VIN Input Voltage Range IIN Supply Current VOUT /VIN Line Regulation 2.7V < VIN < 5.5V 80 350 V/V VOUT/IOUT Load Regulation Sourcing: 0mA IOUT 7mA 25 100 V/mA Sinking: -7mA IOUT 0mA 50 350 V/mA 2.5 -0.3 2.7 V ISC Short Circuit Current TA = +25C, VOUT tied to GND 50 mA tR Turn-on Settling Time VOUT = 0.1% with no load 4 ms Ripple Rejection f = 120Hz -40 dB eN Output Voltage Noise 0.1Hz f 10Hz 30 VP-P VN Broadband Voltage Noise 10Hz f 1kHz 52 VRMS Noise Density f = 1kHz 1.1 V/Hz VOUT/TA Thermal Hysteresis (Note 11) TA = +165C 100 ppm VOUT/t Long Term Stability (Note 12) TA = +25C 50 ppm Electrical Specifications (ISL21080-30, VOUT = 3.0V) VIN = 5.0V, TA = -40C to +85C, IOUT = 0, unless otherwise specified. Boldface limits apply over the operating temperature range, -40C to +85C. PARAMETER DESCRIPTION VOUT Output Voltage VOA VOUT Accuracy @ TA = +25C (Notes 8, 9) TC VOUT Output Voltage Temperature Coefficient (Note 10) VIN Input Voltage Range IIN Supply Current VOUT /VIN Line Regulation VOUT/IOUT Load Regulation CONDITIONS MIN (Note 13) TYP MAX (Note 13) 3.0 -0.2 UNIT V +0.2 % 50 ppm/C 5.5 V 0.31 1.5 A 3.2V < VIN < 5.5V 80 350 V/V Sourcing: 0mA IOUT 7mA 25 100 V/mA Sinking: -7mA IOUT 0mA 50 350 V/mA 3.2 ISC Short Circuit Current TA = +25C, VOUT tied to GND 50 mA tR Turn-on Settling Time VOUT = 0.1% with no load 4 ms Ripple Rejection f = 120Hz -40 dB eN Output Voltage Noise 0.1Hz f 10Hz 30 VP-P VN Broadband Voltage Noise 10Hz f 1kHz 52 VRMS Noise Density f = 1kHz 1.1 V/Hz VOUT/TA Thermal Hysteresis (Note 11) TA = +165C 100 ppm VOUT/t Long Term Stability (Note 12) TA = +25C 50 ppm FN6934 Rev.5.00 Jun 23, 2014 Page 6 of 21 ISL21080 Electrical Specifications (ISL21080-33, VOUT = 3.3V) VIN = 5.0V, TA = -40C to +85C, IOUT = 0, unless otherwise specified. Boldface limits apply over the operating temperature range, -40C to +85C. PARAMETER DESCRIPTION VOUT Output Voltage VOA VOUT Accuracy @ TA = +25C (Notes 8, 9) TC VOUT Output Voltage Temperature Coefficient (Note 10) VIN Input Voltage Range IIN Supply Current VOUT /VIN Line Regulation VOUT/IOUT Load Regulation CONDITIONS MIN (Note 13) TYP MAX (Note 13) UNIT 3.3 -0.2 V +0.2 % 50 ppm/C 5.5 V 0.31 1.5 A 3.5 V < VIN < 5.5V 80 350 V/V Sourcing: 0mA IOUT 10mA 25 100 V/mA Sinking: -10mA IOUT 0mA 50 350 V/mA 3.5 ISC Short Circuit Current TA = +25C, VOUT tied to GND 50 mA tR Turn-on Settling Time VOUT = 0.1% with no load 4 ms Ripple Rejection f = 120Hz -40 dB eN Output Voltage Noise 0.1Hz f 10Hz 30 VP-P VN Broadband Voltage Noise 10Hz f 1kHz 52 VRMS Noise Density f = 1kHz 1.1 V/Hz VOUT/TA Thermal Hysteresis (Note 11) TA = +165C 100 ppm VOUT/t Long Term Stability (Note 12) TA = +25C 50 ppm Electrical Specifications (ISL21080-41 VOUT = 4.096V) VIN = 5.0V, TA = -40C to +85C, IOUT = 0, unless otherwise specified. Boldface limits apply over the operating temperature range, -40C to +85C. PARAMETER DESCRIPTION VOUT Output Voltage VOA VOUT Accuracy @ TA = +25C (Notes 8, 9) TC VOUT Output Voltage Temperature Coefficient (Note 10) VIN Input Voltage Range IIN Supply Current VOUT /VIN Line Regulation VOUT/IOUT Load Regulation CONDITIONS MIN (Note 13) TYP MAX (Note 13) 4.096 -0.2 UNIT V +0.2 % 50 ppm/C 8.0 V 0.5 1.5 A 4.5 V < VIN < 8.0V 80 350 V/V Sourcing: 0mA IOUT 10mA 10 100 V/mA Sinking: -10mA IOUT 0mA 20 350 V/mA 4.5 ISC Short Circuit Current TA = +25C, VOUT tied to GND 80 mA tR Turn-on Settling Time VOUT = 0.1% with no load 4 ms Ripple Rejection f = 120Hz -40 dB eN Output Voltage Noise 0.1Hz f 10Hz 30 VP-P VN Broadband Voltage Noise 10Hz f 1kHz 52 VRMS Noise Density f = 1kHz 1.1 V/Hz VOUT/TA Thermal Hysteresis (Note 11) TA = +165C 100 ppm VOUT/t Long Term Stability (Note 12) TA = +25C 50 ppm FN6934 Rev.5.00 Jun 23, 2014 Page 7 of 21 ISL21080 Electrical Specifications (ISL21080-50 VOUT = 5.0V) VIN = 6.5V, TA = -40C to +85C, IOUT = 0, unless otherwise specified. Boldface limits apply over the operating temperature range, -40C to +85C. PARAMETER DESCRIPTION MIN (Note 13) CONDITIONS TYP MAX (Note 13) UNIT VOUT Output Voltage VOA VOUT Accuracy @ TA = +25C (Notes 8, 9) TC VOUT Output Voltage Temperature Coefficient (Note 10) VIN Input Voltage Range IIN Supply Current VOUT /VIN Line Regulation 5.5 V < VIN < 8.0V 80 350 V/V VOUT/IOUT Load Regulation Sourcing: 0mA IOUT 10mA 10 100 V/mA Sinking: -10mA IOUT 0mA 20 350 V/mA Short Circuit Current TA = +25C, VOUT tied to GND 80 mA ISC 5.0 -0.2 5.5 0.5 V +0.2 % 50 ppm/C 8.0 V 1.5 A Turn-on Settling Time VOUT = 0.1% with no load 4 ms Ripple Rejection f = 120Hz -40 dB eN Output Voltage Noise 0.1Hz f 10Hz 30 VP-P VN Broadband Voltage Noise 10Hz f 1kHz 52 VRMS tR Noise Density f = 1kHz 1.1 V/Hz VOUT/TA Thermal Hysteresis (Note 11) TA = +165C 100 ppm VOUT/t Long Term Stability (Note 12) TA = +25C 50 ppm NOTES: 10. Over the specified temperature range. Temperature coefficient is measured by the box method whereby the change in VOUT is divided by the temperature range; in this case, -40C to +85C = +125C. 11. Thermal Hysteresis is the change of VOUT measured @ TA = +25C after temperature cycling over a specified range, TA. VOUT is read initially at TA = +25C for the device under test. The device is temperature cycled and a second VOUT measurement is taken at +25C. The difference between the initial VOUT reading and the second VOUT reading is then expressed in ppm. For TA = +125C, the device under test is cycled from +25C to +85C to -40C to +25C. 12. Long term drift is logarithmic in nature and diminishes over time. Drift after the first 1000 hours will be approximately 10ppm/1khrs. 13. Parameters with MIN and/or MAX limits are 100% tested at +25C, unless otherwise specified. Temperature limits established by characterization and are not production tested. Typical Performance Characteristics Curves VOUT = 0.9V, VIN = 3.0V, IOUT = 0mA, TA = +25C unless otherwise specified. 0.6 0.6 0.5 0.5 HIGH IIN (A) IIN (A) 0.3 LOW 0.2 TYP 0.3 0.2 -40C +25C 3.6 4.0 VIN (V) 4.4 0.1 0.1 0 2.0 +85C 0.4 0.4 2.4 2.8 3.2 3.6 4.0 VIN (V) 4.4 FIGURE 2. IIN vs VIN, 3 UNITS FN6934 Rev.5.00 Jun 23, 2014 4.8 5.2 0 2.0 2.4 2.8 3.2 4.8 5.2 FIGURE 3. IIN vs VIN OVER-TEMPERATURE Page 8 of 21 ISL21080 Typical Performance Characteristics Curves VOUT = 0.9V, VIN = 3.0V, IOUT = 0mA, TA = +25C unless otherwise specified. (Continued) 200 0.90015 150 HIGH 0.90005 0.90000 0.89995 TYP 0.89990 0.89985 0.89980 2.0 2.4 2.8 3.2 3.6 4.0 VIN (V) 4.4 4.8 +85C 100 VIN = 3.0V VOUT (V) NORMALIZED TO LOW 0.90010 0.9V AT VIN = 3.0V VOUT (V) NORMALIZED TO 0.90020 50 0 -50 -150 5.2 +25C -40C -100 2.0 2.4 2.8 3.2 3.6 4.0 VIN (V) 4.4 4.8 5.2 FIGURE 5. LINE REGULATION OVER-TEMPERATURE FIGURE 4. LINE REGULATION, 3 UNITS 200 0.9010 0.9005 100 TYP VOUT (mV) NORMALIZED TO +25C VOUT (V) 150 LOW 0.9000 HIGH VIN = +0.3V 50 0 -50 VIN = -0.3V -100 0.8995 -150 0.8990 -40 -30 -20 -10 0 10 20 30 40 50 60 70 -200 80 0 0.5 1.0 1.5 2.0 3.0 3.5 4.0 4.5 5.0 FIGURE 7. LINE TRANSIENT RESPONSE, WITH CAPACITIVE LOAD FIGURE 6. VOUT vs TEMPERATURE NORMALIZED to +25C 200 500 VIN = +0.3V 150 2.5 TIME (s) TEMPERATURE (C) +85C 50 VOUT (V) VOUT (mV) 100 0 -50 -40C VIN = -0.3V -100 +25C -150 -200 0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 TIME (s) FIGURE 8. LINE TRANSIENT RESPONSE FN6934 Rev.5.00 Jun 23, 2014 4.0 4.5 5.0 -500 -10 -9 -8 -7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 8 9 10 SINKING SOURCING LOAD (mA) FIGURE 9. LOAD REGULATION OVER-TEMPERATURE Page 9 of 21 ISL21080 Typical Performance Characteristics Curves VOUT = 0.9V, VIN = 3.0V, IOUT = 0mA, TA = +25C unless otherwise specified. (Continued) 1000 500 800 400 ILOAD = +7mA 600 200 VOUT (mV) VOUT (mV) 400 200 0 -200 100 0 -100 -400 -200 -600 -300 ILOAD = -7mA -800 -1000 ILOAD = +50A 300 0 1 2 3 4 ILOAD = -50A -400 5 6 TIME (ms) 7 8 9 -500 0 10 1 FIGURE 10. LOAD TRANSIENT RESPONSE 4 5 6 TIME (ms) 7 8 9 10 3.5 1.4 NO LOAD 3.0 7mA 1.2 2.5 LOW 1.0 VOUT (V) VOUT (V) 3 FIGURE 11. LOAD TRANSIENT RESPONSE 1.6 0.8 0.6 2.0 VDD TYP HIGH 1.5 1.0 0.4 0.5 0.2 0 1.0 1.2 2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 0 0 3.0 0.3 0.6 0.9 TIME (ms) VIN (V) 1.2 1.5 FIGURE 13. TURN-ON TIME FIGURE 12. DROPOUT Typical Performance Characteristics Curves VOUT = 1.5V, VIN = 3.0V, IOUT = 0mA, TA = +25C unless otherwise specified. 500 500 UNIT 1 400 400 +85C 300 UNIT 3 IN (nA) IN (nA) UNIT 2 200 -40C +25C 200 100 100 0 2.7 300 3.1 3.5 3.9 4.3 VIN (V) 4.7 FIGURE 14. IIN vs VIN, 3 UNITS FN6934 Rev.5.00 Jun 23, 2014 5.1 5.5 0 2.7 3.1 3.5 3.9 4.3 VIN (V) 4.7 5.1 5.5 FIGURE 15. IIN vs VIN OVER-TEMPERATURE Page 10 of 21 ISL21080 Typical Performance Characteristics Curves VOUT = 1.5V, VIN = 3.0V, IOUT = 0mA, TA = +25C unless otherwise specified. (Continued) 150 125 1.50015 VOUT (V) (NORMALIZED TO VIN = 3V) VOUT (V) (NORMAILIZED TO 1.5V AT VIN = 3V) 1.50020 1.50010 1.50005 UNIT 2 1.50000 UNIT 1 1.49995 UNIT 3 1.49990 1.49985 100 75 50 +25C 25 +85C 0 -25 -50 -75 -100 -40C -125 1.49980 2.7 3.1 3.5 3.9 4.3 VIN (V) 4.7 5.1 -150 2.7 5.5 3.1 3.5 3.9 4.3 VIN (V) 4.7 5.1 5.5 FIGURE 17. LINE REGULATION OVER-TEMPERATURE FIGURE 16. LINE REGULATION, 3 UNITS 1.5005 1.5004 C L = 500pF 1.5003 1.5001 UNIT 1 1.5000 1.4999 50mV/DIV VOUT (V) V IN = 0.3V UNIT 2 1.5002 UNIT 3 1.4998 V IN = -0.3V 1.4997 1.4996 1.4995 -40 -30 -20 -10 0 10 20 30 40 VIN (V) 50 60 70 80 1ms/DIV FIGURE 18. VOUT vs TEMPERATURE NORMALIZED to +25C FIGURE 19. LINE TRANSIENT RESPONSE, WITH CAPACITIVE LOAD 900 C L = 0pF 700 V IN = 0.3V 50mV/DIV VOUT (V) 500 +25C 300 100 0 -40C -100 V IN = -0.3V +85C -300 -500 1ms/DIV FIGURE 20. LINE TRANSIENT RESPONSE FN6934 Rev.5.00 Jun 23, 2014 -7 -6 -5 SINKING -4 -3 -2 -1 0 1 2 OUTPUT CURRENT 3 4 5 6 7 SOURCING FIGURE 21. LOAD REGULATION OVER-TEMPERATURE Page 11 of 21 ISL21080 Typical Performance Characteristics Curves VOUT = 1.5V, VIN = 3.0V, IOUT = 0mA, TA = +25C 500mV/DIV unless otherwise specified. (Continued) 100mV/DIV IL = 7mA IL = 50A IL = -50A IL = -7mA 2ms/DIV 1ms/DIV FIGURE 22. LOAD TRANSIENT RESPONSE FIGURE 23. LOAD TRANSIENT RESPONSE 3.5 1.52 NO LOAD 3.0 1.50 2.5 1.48 VOLTAGE (V) VOUT (V) 7mA LOAD 1.46 1.44 1.5 1.0 1.40 0.5 2.0 2.5 3.0 3.5 VIN (V) 4.0 4.5 5.0 0 0 5.5 1.0 1.5 2.0 2.5 3.0 TIME (ms) 3.5 4.0 4.5 5.0 NO LOAD -10 120 -20 1nF 100 PSRR (dB) ZOUT () 0.5 0 NO LOAD 140 80 10nF 60 -30 1nF 10nF -40 -50 40 100nF 20 0 UNIT 3 UNIT 2 FIGURE 25. TURN-ON TIME FIGURE 24. DROPOUT 160 UNIT 1 2.0 1.42 1.38 1.5 VIN -60 100nF 10 100 1k 10k FREQUENCY (Hz) FIGURE 26. ZOUT vs FREQUENCY FN6934 Rev.5.00 Jun 23, 2014 100k 1M -70 10 100 1k 10k FREQUENCY (Hz) 100k 1M FIGURE 27. PSRR vs FREQUENCY Page 12 of 21 ISL21080 Typical Performance Characteristics Curves 1.6 1.6 NO LOAD 7mA 1.4 1.2 1.2 1.0 1.0 VOUT (V) VOUT (V) 1.4 0.8 0.6 0.8 0.4 0.2 0.2 1.4 1.6 1.8 2.0 2.2 VIN (V) 2.4 2.6 2.8 0 3.0 1.3 FIGURE 28. DROPOUT, ISL21080-10 1.5 1.7 1.9 2.1 VIN (V) 2.3 2.5 2.7 2.9 FIGURE 29. DROPOUT, ISL21080-12 3.3 3.0 2.9 2.8 NO LOAD 3.2 7mA 2.7 NO LOAD 7mA 3.1 2.6 VOUT (V) VOUT (V) 7mA NO LOAD 0.6 0.4 0 1.2 TA = +25C unless otherwise specified. 2.5 2.4 2.3 2.2 3.0 2.9 2.8 2.1 2.0 2.5 2.7 2.9 3.1 VIN (V) 3.3 2.7 3.0 3.5 4.3 3.5 4.2 7mA 3.4 3.8 4.0 NO LOAD 7mA 4.1 VOUT (V) VOUT (V) 3.6 FIGURE 31. DROPOUT, ISL21080-30 3.6 3.3 4.0 3.2 3.9 3.1 3.8 3.0 3.3 3.4 VIN (V) FIGURE 30. DROPOUT, ISL21080-25 NO LOAD 3.2 3.5 3.7 3.9 VIN (V) 4.1 FIGURE 32. DROPOUT, ISL21080-33 FN6934 Rev.5.00 Jun 23, 2014 4.3 4.5 3.7 4.1 4.3 4.5 4.7 4.9 5.1 VIN (V) FIGURE 33. DROPOUT, ISL21080-41 Page 13 of 21 ISL21080 Typical Performance Characteristics Curves TA = +25C unless otherwise specified. (Continued) 5.3 5.2 NO LOAD 7mA VOUT (V) 5.1 5.0 4.9 4.8 4.7 5.0 5.2 5.4 5.6 5.8 6.0 VIN (V) FIGURE 34. DROPOUT, ISL21080-50 High Current Application 1.502 1.502 VIN = 5V VIN = 5V 1.500 1.498 VIN = 3.5V VREF (V) VREF (V) 1.500 1.496 1.492 0 5 10 15 20 ILOAD (mA) 25 1.496 1.494 30 35 FIGURE 35. DIFFERENT VIN AT ROOM TEMPERATURE Applications Information FGA Technology The ISL21080 series of voltage references use the floating gate technology to create references with very low drift and supply current. Essentially, the charge stored on a floating gate cell is set precisely in manufacturing. The reference voltage output itself is a buffered version of the floating gate voltage. The resulting reference device has excellent characteristics which are unique in the industry: very low temperature drift, high initial accuracy, and almost zero supply current. Also, the reference voltage itself is not limited by voltage bandgaps or zener settings, so a wide range of reference voltages can be programmed (standard voltage settings are provided, but customer-specific voltages are available). The process used for these reference devices is a floating gate CMOS process, and the amplifier circuitry uses CMOS transistors for amplifier and output transistor circuitry. While providing excellent accuracy, there are limitations in output noise level and load regulation due to the MOS device characteristics. These limitations are addressed with circuit techniques discussed in other sections. FN6934 Rev.5.00 Jun 23, 2014 VIN = 3.5V VIN = 3.3V VIN = 3.3V 1.494 1.498 1.492 0 5 10 15 20 25 30 35 ILOAD (mA) FIGURE 36. DIFFERENT VIN AT HIGH TEMPERATURE (+85C) Board Assembly Considerations FGA references provide high accuracy and low temperature drift but some PC board assembly precautions are necessary. Normal Output voltage shifts of 100V to 1mV can be expected with Pb-free reflow profiles or wave solder on multi-layer FR4 PC boards. Precautions should be taken to avoid excessive heat or extended exposure to high reflow or wave solder temperatures, this may reduce device initial accuracy. Post-assembly x-ray inspection may also lead to permanent changes in device output voltage and should be minimized or avoided. If x-ray inspection is required, it is advisable to monitor the reference output voltage to verify excessive shift has not occurred. If large amounts of shift are observed, it is best to add an X-ray shield consisting of thin zinc (300m) sheeting to allow clear imaging, yet block x-ray energy that affects the FGA reference. Special Applications Considerations In addition to post-assembly examination, there are also other X-ray sources that may affect the FGA reference long term accuracy. Airport screening machines contain X-rays and will have a cumulative effect on the voltage reference output accuracy. Carry-on luggage screening uses low level X-rays and is Page 14 of 21 ISL21080 not a major source of output voltage shift, however, if a product is expected to pass through that type of screening over 100 times, it may need to consider shielding with copper or aluminum. Checked luggage X-rays are higher intensity and can cause output voltage shift in much fewer passes, thus devices expected to go through those machines should definitely consider shielding. Note that just two layers of 1/2 ounce copper planes will reduce the received dose by over 90%. The leadframe for the device which is on the bottom also provides similar shielding. VIN = +3.0V 10F VIN VOUT ISL21080 GND 0.001F TO 0.01F REF IN If a device is expected to pass through luggage X-ray machines numerous times, it is advised to mount a 2-layer (minimum) PC board on the top, and along with a ground plane underneath will effectively shield it from 50 to 100 passes through the machine. Since these machines vary in X-ray dose delivered, it is difficult to produce an accurate maximum pass recommendation. ENABLE SERIAL BUS SCK SDAT 12 TO 24-BIT A/D CONVERTER Nanopower Operation FIGURE 37. REFERENCE INPUT FOR ADC CONVERTER Reference devices achieve their highest accuracy when powered up continuously, and after initial stabilization has taken place. This drift can be eliminated by leaving the power on continuously. The ISL21080 is the first high precision voltage reference with ultra low power consumption that makes it possible to leave power on continuously in battery operated circuits. The ISL21080 consumes extremely low supply current due to the proprietary FGA technology. Supply current at room temperature is typically 350nA, which is 1 to 2 orders of magnitude lower than competitive devices. Application circuits using battery power will benefit greatly from having an accurate, stable reference, which essentially presents no load to the battery. In particular, battery powered data converter circuits that would normally require the entire circuit to be disabled when not in use can remain powered up between conversions as shown in Figure 37. Data acquisition circuits providing 12 bits to 24 bits of accuracy can operate with the reference device continuously biased with no power penalty, providing the highest accuracy and lowest possible long term drift. ISL21080 Used as a Low Cost Precision Current Source Using an N-JET and a Nanopower voltage reference, ISL21080, a precision, low cost, high impedance current source can be created. The precision of the current source is largely dependent on the tempco and accuracy of the reference. The current setting resistor contributes less than 20% of the error. Board Mounting Considerations For applications requiring the highest accuracy, board mounting location should be reviewed. Placing the device in areas subject to slight twisting can cause degradation of the accuracy of the reference voltage due to die stresses. It is normally best to place the device near the edge of a board, or the shortest side, as the axis of bending is most limited at that location. Obviously, mounting the device on flexprint or extremely thin PC material will likewise cause loss of reference accuracy. Other reference devices consuming higher supply currents will need to be disabled in between conversions to conserve battery capacity. Absolute accuracy will suffer as the device is biased and requires time to settle to its final value, or, may not actually settle to a final value as power on time may be short. Table 1 shows an example of battery life in years for ISL21080 in various power on condition with 1.5A maximum current consumption. TABLE 1. EXAMPLE OF BATTERY LIFE IN YEARS FOR ISL21080 IN VARIOUS POWER ON CONDITIONS WITH 1.5A MAX CURRENT BATTERY RATING (mAH) CONTINUOUS 50% DUTY CYCLE 10% DUTY CYCLE 40 3 6 30* 225 16.3* 32.6* 163* NOTE: *Typical Li-ion battery has a shelf life of up to 10 years. FN6934 Rev.5.00 Jun 23, 2014 0.01F +8V TO 28V ISET = VOUT RSET IL = ISET + IRSET VIN 0.01F VOUT ISL21080-1.5 VOUT = 1.5V RSET ZOUT > 100M 10k 0.1% 10ppm/C GND ISY ~ 0.31A ISET IL AT 0.1% ACCURACY ~150.3A FIGURE 38. ISL21080 USED AS A LOW COST PRECISION CURRENT SOURCE Page 15 of 21 ISL21080 Noise Performance and Reduction Turn-On Time The output noise voltage in a 0.1Hz to 10Hz bandwidth is typically 30VP-P. This is shown in the plot in the "Typical Performance Characteristics Curves" which begin on page 10. The noise measurement is made with a bandpass filter made of a 1-pole high-pass filter with a corner frequency at 0.1Hz and a 2-pole low-pass filter with a corner frequency at 12.6Hz to create a filter with a 9.9Hz bandwidth. Noise in the 10kHz to 1MHz bandwidth is approximately 400VP-P with no capacitance on the output, as shown in Figure 39. These noise measurements are made with a 2 decade bandpass filter made of a 1-pole high-pass filter with a corner frequency at 1/10 of the center frequency and 1-pole low-pass filter with a corner frequency at 10 times the center frequency. Figure 39 also shows the noise in the 10kHz to 1MHz band can be reduced to about 50VP-P using a 0.001F capacitor on the output. Noise in the 1kHz to 100kHz band can be further reduced using a 0.1F capacitor on the output, but noise in the 1Hz to 100Hz band increases due to instability of the very low power amplifier with a 0.1F capacitance load. For load capacitances above 0.001F, the noise reduction network shown in Figure 40 is recommended. This network reduces noise significantly over the full bandwidth. As shown in Figure 39, noise is reduced to less than 40VP-P from 1Hz to 1MHz using this network with a 0.01F capacitor and a 2k resistor in series with a 10F capacitor. The ISL21080 devices have ultra-low supply current and thus, the time to bias-up internal circuitry to final values will be longer than with higher power references. Normal turn-on time is typically 7ms. This is shown in Figure 38. Since devices can vary in supply current down to >300nA, turn-on time can last up to about 12ms. Care should be taken in system design to include this delay before measurements or conversions are started. Temperature Coefficient The limits stated for temperature coefficient (tempco) are governed by the method of measurement. The overwhelming standard for specifying the temperature drift of a reference, is to measure the reference voltage at two temperatures, take the total variation, (VHIGH - VLOW), and divide by the temperature extremes of measurement (THIGH - TLOW). The result is divided by the nominal reference voltage (at T = +25C) and multiplied by 106 to yield ppm/C. This is the "Box" method for specifying temperature coefficient. NOISE VOLTAGE (VP-P) 400 CL = 0 350 CL = 0.001F 300 CL = 0.1F CL = 0.01F AND 10F + 2k 250 200 150 100 50 0 1 10 100 1k 10k 100k FIGURE 39. NOISE REDUCTION VIN = 3.0V 10F 0.1F VIN VO ISL21080 GND 2k 0.01F 10F FIGURE 40. NOISE REDUCTION NETWORK FN6934 Rev.5.00 Jun 23, 2014 Page 16 of 21 ISL21080 Typical Application Circuits VIN = 3.0V R = 200 2N2905 VIN ISL21080 VOUT 2.5V/50mA 0.001F GND FIGURE 41. PRECISION 2.5V 50mA REFERENCE 2.7V TO 5.5V 0.1F 10F VIN VOUT ISL21080 GND 0.001F VCC RH VOUT X9119 + SDA 2-WIRE BUS SCL VSS - VOUT (BUFFERED) RL FIGURE 42. 2.5V FULL SCALE LOW-DRIFT 10-BIT ADJUSTABLE VOLTAGE SOURCE 2.7V TO 5.5V 0.1F 10F VIN VOUT ISL21080 + VOUT SENSE - LOAD GND FIGURE 43. KELVIN SENSED LOAD FN6934 Rev.5.00 Jun 23, 2014 Page 17 of 21 ISL21080 Revision History The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to web to make sure you have the latest Rev. DATE REVISION June 23, 2014 FN6934.5 Converted to New Template Updated POD with following changes: In Detail A, changed lead width dimension from 0.13+/-0.05 to 0.085-0.19 Changed dimension of foot of lead from 0.31+/-0.10 to 0.38+/-0.10 In Land Pattern, added 0.4 Rad Typ dimension In Side View, changed height of package from 0.91+/-0.03 to 0.95+/-0.07 CHANGE May, 12, 2010 FN6934.4 Changed Theta JA in the "Thermal Information" on page 3 from 170 to 275. Added Theta JC and applicable note. April 29, 2010 FN6934.3 Incorrect Thermal information, needs to be re-evaluated and added at a later date when the final data is available. Removed Theta JC and applicable note from "Thermal Information" on page 3. April 14, 2010 Corrected y axis label on Figure 9 from "VOUT (V)" to "VOUT (V)" April 6, 2010 Source/sink for 0.9V option changed from 7mA to 10mA Line regulation condition for 0.9V changed from 2.7V to 2V Line regulation typical for 0.9V option changed from 10 to 30V/V TA in Thermal Hysterisis conditions of 0.9V option changed from 165C to 125C Moved "Board Assembly Considerations" and "Special Applications Considerations" to page 14. Deleted "Handling and Board Mounting" section since "Board Assembly Considerations" on page 14 contains same discussion. Added "Special Note: Post-assembly x-ray inspection may lead to permanent changes in device output voltage and should be minimized or avoided." to "ISL21080" on page 1 Figures 2 and 3 revised to show line regulation and Iin down to 2V. Figures 4 and 5 revised to show Vin down to 2V. Added "Initial accuracy can change 10mV or more under extreme radiation." to Note 9 on page 3. April 1, 2010 1. page 3: Change Vin Min from 2.7 to 2.0 2. page 3: Change Iin Typ from 0.31 to 0.35 3. page 3: Change Line Reg Typ from 80 to 10 4. page 3: Change Load Reg Condition from 7mA to 10mA and -7mA to -10mA 5. page 3: Change Load Reg Typ for Source from 25 to 6 and Sink from 50 to 23. 6. page 3: Change Isc Typ from 50 to 30 7. page 3: Change tR from 4 to 1 8. Change Ripple Rejection typ for all options from -30 to -40 9. page 3: Change eN typ from 30 to 40V 10. page 3: Change VN typ from 50 to 10V 11. page 3: Change Noise Density typ from 1.1 to 2.2 12. page 3: Change Long Term Stability from 50 to 60 13. Added Figure 2 to 13 on page 8 to page 10 for 0.9V curves. 14. Added Figure 28 to 34 on page 13 to page 14 for other options Dropout curve. 15. page 1: Change Input Voltage Range for 0.9V option from TBD to 2V to 5.5V 16. Added latch up to "Absolute Maximum Ratings" on page 3 17. Added Junction Temperature to "Thermal Information" on page 3 18. Added JEDEC standards used at the time of testing for "ESD Ratings" on page 3 19. HBM in "Absolute Maximum Ratings" on page 3 changed from 5.5kV to 5kV 20. Added Theta JC and applicable note. March 25, 2010 FN6934 Rev.5.00 Jun 23, 2014 Throughout- Converted to new format. Changes made as follows: Moved "Pin Configuration" and "Pin Descriptions" to page 2 Added "Related Literature" to page 1 Added key selling feature graphic Figure 1 to page 1 Added "Boldface limits apply..." note to common conditions of Electrical Specifications tables on page 3 through page 8. Bolded applicable specs. Added Note 13 to MIN MAX columns of all Electrical Specifications tables. Added ""Environmental Operating Conditions" to page 3 and added Note 5 Added "The process used for these reference devices is a floating gate CMOS process, and the amplifier circuitry uses CMOS transistors for amplifier and output transistor circuitry. While providing excellent accuracy, there are limitations in output noise level and load regulation due to the MOS device characteristics. These limitations are addressed with circuit techniques discussed in other sections." on page 14 Page 18 of 21 ISL21080 Revision History The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to web to make sure you have the latest Rev. DATE REVISION Oct 14,2009 FN6934.2 1. Removed "Coming Soon" on page 1 and 2 for -10, -20, -41, and -50 options. 2. Page 1. Moved "ISL21080-505.5V to 8.0V" from bullet to sub-bullet. 3. Update package outline drawing P3.064 to most recent revision. Updates to package were to add land pattern and move dimensions from table onto drawing (no change to package dimensions) Sep 04, 2009 FN6934.1 Converted to new Intersil template. Added Revision History and Products Information. Updated Ordering Information to match Intrepid, numbered all notes and added Moisture Sensitivity Note with links. Moved Pin Descriptions to page 1 to follow pinout Changed in Features Section From: Reference Output Voltage1.25V, 1.5V, 2.500V, 3.300V To: Reference Output Voltage 0.900V, 1.024V, 1.250V, 1.500V, 2.048V, 2.500V, 3.000V, 3.300V, 4.096V, 5.000V From: Initial Accuracy: 1.5V0.5% To: Initial Accuracy: ISL21080-09 and -100.7% ISL21080-12 0.6% ISL21080-150.5% ISL21080-20 and -250.3% ISL21080-30, -33, -41, and -500.2% FROM: Input Voltage Range ISL21080-12 (Coming Soon)2.7V to 5.5V ISL21080-152.7V to 5.5V ISL21080-25 (Coming Soon)2.7V to 5.5V ISL21080-33 (Coming Soon)3.5V to 5.5V TO: Input Voltage Range: ISL21080-09, -10, -12, -15, -20, and -252.7V to 5.5V ISL21080-09, -10, and 20 (Coming Soon) ISL21080-303.2V to 5.5V ISL21080-333.5V to 5.5V ISL21080-41 (Coming Soon)4.5V to 8.0V Added: ISL21080-50 (Coming Soon)5.5V to 8.0V Output Voltage Noise 30VP-P (0.1Hz to 10Hz) Updated Electrical Spec Tables by Tables with Voltage References 9, 10, 12, 20, 25, 30, 33 and 41. Added to Abs Max Ratings: VIN to GND (ISL21080-41 and 50 only-0.5V to +10V VOUT to GND (10s) (ISL21080-41 and 50 only-0.5V to +5.1V Changed Tja in Thermal information from "202.70" to "170" to match ASYD in Intrepid Added Note: Post-assembly x-ray inspection may also lead to permanent changes in device output voltage and should be minimized or avoided. Most inspection equipment will not affect the FGA reference voltage, but if x-ray inspection is required, it is advisable to monitor the reference output voltage to verify excessive shift has not occurred. Added Special Applications Considerations Section on page 12. July 28,2009 FN6934.0 Initial Release. FN6934 Rev.5.00 Jun 23, 2014 CHANGE Page 19 of 21 ISL21080 About Intersil Intersil Corporation is a leading provider of innovative power management and precision analog solutions. The company's products address some of the largest markets within the industrial and infrastructure, mobile computing and high-end consumer markets. For the most updated datasheet, application notes, related documentation and related parts, please see the respective product information page found at www.intersil.com. You may report errors or suggestions for improving this datasheet by visiting www.intersil.com/ask. Reliability reports are also available from our website at www.intersil.com/supporty (c) Copyright Intersil Americas LLC 2009-2014. All Rights Reserved. All trademarks and registered trademarks are the property of their respective owners. For additional products, see www.intersil.com/en/products.html Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted in the quality certifications found at www.intersil.com/en/support/qualandreliability.html Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com FN6934 Rev.5.00 Jun 23, 2014 Page 20 of 21 ISL21080 Package Outline Drawing P3.064 3 LEAD SMALL OUTLINE TRANSISTOR PLASTIC PACKAGE (SOT23-3) Rev 3, 3/12 2.920.12 4 DETAIL "A" C L 0.085 - 0.19 2.370.27 1.300.10 4 C L 0.950 0.4350.065 0 - 8 deg. 0.20 M C TOP VIEW 10 TYP (2 plcs) 0.25 0.950.07 GAUGE PLANE 1.000.12 SEATING PLANE C SEATING PLANE 0.10 C 0.380.10 5 0.013(MIN) 0.100(MAX) SIDE VIEW DETAIL "A" (0.60) NOTES: (2.15) 1. Dimensions are in millimeters. Dimensions in ( ) for Reference Only. 2. Dimensioning and tolerancing conform to AMSEY14.5m-1994. 3. Reference JEDEC TO-236. 4. Dimension does not include interlead flash or protrusions. Interlead flash or protrusions shall not exceed 0.25mm per side. 5. Footlength is measured at reference to gauge plane. (1.25) (0.4 RAD TYP.) (0.95 typ.) TYPICAL RECOMMENDED LAND PATTERN FN6934 Rev.5.00 Jun 23, 2014 Page 21 of 21