MAX9012EUA+T - Maxim Integrated

General Description

The MAX9010/MAX9011/MAX9013 single and MAX9012

dual, high-speed comparators operate from a single

4.5V to 5.5V power supply and feature low-current con-

sumption. They have precision differential inputs and

TTL outputs. They feature short propagation delay (5ns,

typ), low-supply current, and a wide common-mode

input range that includes ground. They are ideal for low-

power, high-speed, single-supply applications.

The comparator outputs remain stable through the linear

region when driven with slow-moving or low input-over-

drive signals, eliminating the output instability common

to other high-speed comparators. The input voltage

range extends to 200mV below ground with no output

phase reversal. The MAX9013 features complementary

outputs and both the MAX9011/MAX9013 have a latch

enable input (LE). The MAX9013 is an improved plug-in

replacement for the industry-standard MAX913 and

LT1016/LT1116, offering lower power and higher speed

when used in a single 5V supply application.

For space-critical designs, the single MAX9010 is avail-

able in the tiny 6-pin SC70 package. The single

MAX9011 is available in a space-saving 6-pin SOT23

package. The dual MAX9012 and the single MAX9013

are available in 8-pin µMAX and 8-pin SO packages. All

products in the family are guaranteed over the extended

temperature range of -40°C to +85°C.

Applications

High-Speed Signal Squaring

Zero-Crossing Detectors

High-Speed Line Receivers

High-Speed Sampling Circuits

High-Speed Triggers

Fast Pulse-Width/Height Discriminators

____________________________Features

♦Ultra-Fast, 5ns Propagation Delay

♦Low Quiescent Current:

900µA (MAX9010/MAX9011)

1.3mA (MAX9013)

2.4mA (MAX9012)

♦Single-Supply 4.5V to 5.5V Applications

♦Input Range Extends Below Ground

♦No Minimum Input Signal Slew-Rate Requirement

♦No Supply-Current Spikes During Switching

♦Stable when Driven with Slow-Moving Inputs

♦No Output Phase Reversal for Overdriven Inputs

♦TTL-Compatible Outputs (Complementary for

MAX9013)

♦Latch Function Included (MAX9011/MAX9013)

♦High-Precision Comparators

0.7mV Input Offset Voltage

3.0V/mV Voltage Gain

♦Available in Tiny 6-Pin SC70 and SOT23 Packages

MAX9010–MAX9013

SC70, 5ns, Low-Power, Single-Supply,

Precision TTL Comparators

________________________________________________________________ Maxim Integrated Products 1

TOP VIEW

GND

IN-IN+

16V

OUT

SC70

GND

IN-IN+

16V

5LE

OUT

SOT23

MAX9011

+ –

MAX9010

+ – OUTB

GNDINB-

VCC

OUTAINA-

INB+

INA+

SO/µMAX

GND

LEN.C.

7 OUTIN+

IN-

VCC

SO/µMAX

MAX9012

MAX9013

OUT

Pin Configurations

19-1932; Rev 1; 1/02

Ordering Information

PART TEMP RANGE PIN-

PACKAGE

TOP

MARK

MAX9010EXT-T -40°C to +85°C 6 SC70-6 AAA

MAX9011EUT-T -40°C to +85°C 6 SOT23-6 AADD

MAX9012EUA -40°C to +85°C 8 µMAX —

MAX9012ESA -40°C to +85°C 8 SO —

MAX9013EUA -40°C to +85°C 8 µMAX —

MAX9013ESA -40°C to +85°C 8 SO —

Selector Guide appears at end of data sheet.

For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at

1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.

MAX9010–MAX9013

SC70, 5ns, Low-Power, Single-Supply,

Precision TTL Comparators

2 _______________________________________________________________________________________

ABSOLUTE MAXIMUM RATINGS

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional

operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to

absolute maximum rating conditions for extended periods may affect device reliability.

Power Supply (VCC to GND) ...................................-0.3V to +6V

Analog Input (IN+ or IN-) to GND...............-0.3V to (VCC + 0.3V)

Input Current (IN+ or IN-) .................................................±30mA

LE to GND ..................................................-0.3V to (VCC + 0.3V)

Continuous Output Current...............................................±40mA

Continuous Power Dissipation (TA= +70°C)

6-Pin SC70 (derate 3.1mW/°C above +70°C).............245mW

6-Pin SOT23 (derate 8.7mW/°C above +70°C)...........696mW

8-Pin µMAX (derate 4.5mW/°C above +70°C) ............362mW

8-Pin SO (derate 5.9mW/°C above +70°C).................471mW

Operating Temperature Range ...........................-40°C to +85°C

Junction Temperature......................................................+150°C

Storage Temperature Range .............................-65°C to +150°C

Lead Temperature (soldering, 10s) .................................+300°C

ELECTRICAL CHARACTERISTICS (MAX9010/MAX9011)

(VCC = 5V, VLE = 0 (MAX9011 only), VCM = 0, TA= TMIN to TMAX, unless otherwise noted. Typical values are at TA= +25°C.) (Note 1)

PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS

Supply Voltage Range VCC Inferred from VOS tests 4.5 5.5 V

Power-Supply Current (Note 2) ICC 0.90 2.1 mA

TA = +25°C±1±5

Input Offset Voltage

(Note 3) VOS TA = TMIN to TMAX ±7 mV

Input Offset-Voltage Drift ∆VOS/∆T±2 µV /°C

Input Bias Current IB±0.5 ±2 µA

Input Offset Current IOS ±40 ±200 nA

Differential Input Resistance

(Note 4) RIN

(

D IFF

)

VIN(DIFF) = ±10mV 250 kΩ

Common-Mode Input

Resistance (Note 4) RIN

(

)

-0.2V ≤ VCM ≤ (VCC - 1.9V) 1 MΩ

Common-Mode Input Voltage

Range (Note 4) VCM Inferred from VOS tests -0.2 VCC - 1.9 V

Common-Mode Rejection

Ratio CMRR -0.2V ≤ VCM ≤ (VCC - 1.9V) 95 dB

Power-Supply Rejection Ratio PSRR VCC = 4.5V to 5.5V 82 dB

Small-Signal Voltage Gain AV1V ≤ VOUT ≤ 2V 3000 V/V

ISINK = 0 0.3 0.5

Output Low Voltage VOL VIN ≥ 100mV ISINK = 4mA 0.5 0.6 V

ISOURCE = 0 2.7 3.3

Output High Voltage VOH VIN ≥ 100mV,

VCC = 4.5V ISOURCE = 4mA 2.4 2.9 V

Sinking 20

Output Short-Circuit Current IOUT Sourcing 30 mA

Latch Enable Pin High Input

Voltage VIH MAX9011 only 2 V

Latch Enable Pin Low Input

Voltage VIL MAX9011 only 0.8 V

Latch Enable Pin Bias Current IIH, IIL MAX9011 only,

VLE = 0 and VLE = 5V ±25 µA

MAX9010–MAX9013

SC70, 5ns, Low-Power, Single-Supply,

Precision TTL Comparators

_______________________________________________________________________________________ 3

ELECTRICAL CHARACTERISTICS (MAX9010/MAX9011) (continued)

(VCC = 5V, VLE = 0 (MAX9011 only), VCM = 0, TA= TMIN to TMAX, unless otherwise noted. Typical values are at TA= +25°C.) (Note 1)

PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS

Latch Setup Time (Note 8) tSU MAX9011 only 2 0 ns

Latch Hold Time (Note 8) tHMAX9011 only 2 0.5 ns

Latch Propagation Delay

(Note 8) tLPD MAX9011 only 5 ns

Input Noise-Voltage Density enf = 100kHz 6 nV/√Hz

VOVERDRIVE = 100mV 5 8

CLOAD = 5pF,

TA = +25°CVOVERDRIVE = 5mV 5.5 9

VOVERDRIVE = 100mV 9

Propagation Delay (Note 6) tPD+, tPD- CLOAD = 5pF,

TA = TMIN to TMAX VOVERDRIVE = 5mV 10

Output Rise Time tR0.5V ≤ VOUT ≤ 2.5V 3 ns

Output Fall Time tF2.5V ≥ VOUT ≥ 0.5V 2 ns

MAX9010EXT 0.8

Input Capacitance CIN MAX9011EUT 1.2 pF

Power-Up Time tON 1µs

ELECTRICAL CHARACTERISTICS (MAX9012/MAX9013)

(VCC = 5V, VLE = 0 (MAX9013 only), VCM = 0, TA= TMIN to TMAX, unless otherwise noted. Typical values are at TA= +25°C.) (Note 1)

PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS

Supply Voltage Range VCC Inferred from PSRR test 4.5 5.5 V

MAX9012 2.4 4.2

Power-Supply Current (Note 2) ICC MAX9013 1.3 2.3 mA

TA = +25°C ±0.7 ±3

Input Offset Voltage

(Note 5) VOS TA = TMIN to TMAX ±5.5 mV

Input Offset-Voltage Drift ∆VOS/∆T±2µV /°C

Input Bias Current IB±0.5 ±2 µA

Input Offset Current IOS ±40 ±200 nA

Differential Input Resistance

(Note 4) RIN

(

D IFF

)

VIN(DIFF) = ±10mV 250 kΩ

Common-Mode Input

Resistance (Note 4) RIN

(

)

-0.2V ≤ VCM ≤ (VCC - 1.9V) 1 MΩ

Common-Mode Input Voltage

Range (Note 4) VCM Inferred from CMRR test -0.2 VCC - 1.9 V

Common-Mode Rejection

Ratio CMRR -0.2V ≤ VCM ≤ (VCC - 1.9V) 75 95 dB

Power-Supply Rejection Ratio PSRR VCC = 4.5V to 5.5V 63 82 dB

MAX9010–MAX9013

SC70, 5ns, Low-Power, Single-Supply,

Precision TTL Comparators

4 _______________________________________________________________________________________

ELECTRICAL CHARACTERISTICS (MAX9012/MAX9013) (continued)

(VCC = 5V, VLE = 0 (MAX9013 only), VCM = 0, TA= TMIN to TMAX, unless otherwise noted. Typical values are at TA= +25°C.) (Note 1)

PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS

Small-Signal Voltage Gain AV1V ≤ VOUT ≤ 2V 1000 3000 V/V

ISINK = 0 0.3 0.5

Output Low Voltage VOL VIN ≥ 100mV ISINK = 4mA 0.5 0.6 V

ISOURCE = 0 2.7 3.3

Output High Voltage VOH VIN ≥ 100mV,

VCC = 4.5V ISOURCE = 4mA 2.4 2.9 V

Sinking 20

Output Short-Circuit Current IOUT Sourcing 30 mA

Latch Enable Pin High Input

Voltage VIH MAX9013 only 2 V

Latch Enable Pin Low Input

Voltage VIL MAX9013 only 0.8 V

Latch Enable Pin Bias Current IIH, IIL MAX9013 only

VLE = 0 and VLE = 5V ±25 µA

Input Noise-Voltage Density enf = 100kHz 6 nV/√Hz

VOVERDRIVE = 100mV 5 8

CLOAD = 5pF,

TA = +25°CVOVERDRIVE = 5mV 5.5 9

VOVERDRIVE = 100mV 9

Propagation Delay (Note 6) tPD+, tPD- CLOAD = 5pF,

TA = TMIN to TMAX VOVERDRIVE = 5mV 10

Differential Propagation Delay

(Notes 6, 7) ∆tPD± VIN = 100mV step, CLOAD = 5pF,

VOD = 5mV 23ns

Channel-to-Channel

Propagation Delay (Note 6) ∆tPD

(

ch-ch

)

MAX9012 only, VIN = 100mV step,

CLOAD = 5pF, VOD = 5mV 500 ps

Output Rise Time tR0.5V ≤ VOUT ≤ 2.5V 3 ns

Output Fall Time tF2.5V ≥ VOUT ≥ 0.5V 2 ns

Latch Setup Time (Note 8) tSU MAX9013 only 2 0 ns

Latch Hold Time (Note 8) tHMAX9013 only 2 0.5 ns

Latch Propagation Delay

(Note 8) tLPD MAX9013 only 5 ns

MAX9012EUA/MAX9013EUA 1.5

Input Capacitance CIN MAX9012ESA/MAX9013ESA 2 pF

Power-Up Time tON 1µs

Note 1: All specifications are 100% tested at TA= +25°C; temperature limits are guaranteed by design.

Note 2: Quiescent Power-Supply Current is slightly higher with the comparator output at VOL. This parameter is specified with the worst-

case condition of VOUT = VOL for the MAX9010/MAX9011 and both outputs at VOL for the MAX9012. For the MAX9013, which

has complementary outputs, the power-supply current is specified with either OUT = VOL, OUT = VOH or OUT = VOH, OUT =

VOL (power-supply current is equal in either case).

Note 3: Input Offset Voltage is tested and specified with the Input Common-Mode Voltage set to either extreme of the Input Common-

Mode Voltage Range (-0.2V to (VCC - 1.9V)) and with the Power-Supply Voltage set to either extreme of the Power-Supply

Voltage Range (4.5V to 5.5V).

MAX9010–MAX9013

SC70, 5ns, Low-Power, Single-Supply,

Precision TTL Comparators

_______________________________________________________________________________________ 5

Note 4: Although Common-Mode Input Voltage Range is restricted to -0.2V ≤VCM ≤(VCC - 1.9V), either or both inputs can go to either

absolute maximum voltage limit, i.e., from -0.3V to (VCC + 0.3V), without damage. The comparator will make a correct (and fast)

logic decision provided that at least one of the two inputs is within the specified common-mode range. If both inputs are outside

the common-mode range, the comparator output state is indeterminate.

Note 5: For the MAX9012, Input Offset Voltage is defined as the input voltage(s) required to make the OUT output voltage(s) remain

stable at 1.4V. For the MAX9013, it is defined as the average of two input offset voltages, measured by forcing first the OUT

output, then the OUT output to 1.4V.

Note 6: Propagation delay for these high-speed comparators is guaranteed by design because it cannot be accurately measured

with low levels of input overdrive voltage using automatic test equipment in production. Note that for low overdrive

conditions, VOS is added to the overdrive.

Note 7: Differential Propagation Delay, measured either on a single output of the MAX9012/MAX9013 (or between OUT and OUT

outputs on the MAX9013) is defined as: ∆tPD(±) = |(tPD+) - (tPD-)|.

Note 8: Latch times are guaranteed by design. Latch setup time (tSU) is the interval in which the input signal must be stable prior to

asserting the latch signal. The hold time (tH) is the interval after the latch is asserted in which the input signal must remain

stable. Latch propagation delay (tLPD) is the delay time for the output to respond when the latch enable pin is deasserted

(see Figure 1).

t = 5ns/div

RESPONSE TO -5mV OVERDRIVE

IN: 50mV/div

OUT: 1V/div

+100mV

MAX9010–13 toc02

OUT

6.0

3.5

1 10 100

4.0

MAX9010–13 toc03

OVERDRIVE (mV)

PROPAGATION DELAY (ns)

4.5

5.0

5.5

PROPAGATION DELAY

vs. INPUT OVERDRIVE

3.0

tPD(+)

tPD(-)

t = 5ns/div

RESPONSE TO +5mV OVERDRIVE

IN: 50mV/div

OUT: 1V/div

-100mV

MAX9010–13 toc01

OUT

Typical Operating Characteristics

(VCC = 5V, CL= 15pF, TA = +25°C, unless otherwise noted.)

MAX9010–MAX9013

SC70, 5ns, Low-Power, Single-Supply,

Precision TTL Comparators

6 _______________________________________________________________________________________

Typical Operating Characteristics (continued)

(VCC = 5V, CL= 15pF, TA = +25°C, unless otherwise noted.)

10 10k1k100

PROPAGATION DELAY

vs. SOURCE RESISTANCE

MAX9010–13 toc04

SOURCE RESISTANCE (Ω)

PROPAGATION DELAY (ns)

tPD(+)

tPD(-)

4.0

4.5

5.0

5.5

6.0

6.5

7.0

7.5

8.0

10 20 30 40 50 60

PROPAGATION DELAY

vs. LOAD CAPACITANCE

MAX9010–13 toc05

LOAD CAPACITANCE (pF)

PROPAGATION DELAY (ns)

tPD(+)

tPD(-)

6.0

3.5

1 10 100

4.0

MAX9010–13 toc03

OVERDRIVE (mV)

PROPAGATION DELAY (ns)

4.5

5.0

5.5

PROPAGATION DELAY

vs. INPUT OVERDRIVE

3.0

tPD(+)

tPD(-)

RESPONSE TO 50MHz ±10mV

SINE WAVE

MAX9010–13 toc07

10ns/div

A: Input, 10mV/div

B: Output, 2V/div

RESPONSE TO 10kHz TRIANGLE WAVE

MAX9010–13 toc08

20µs/div

A: Input, 20mV/div

B: Output, 2V/div

-0.9

-0.7

-0.8

-0.5

-0.6

-0.4

-0.3

-40 10-15 35 60 85

OFFSET VOLTAGE

vs. TEMPERATURE

MAX9010–13 toc09

TEMPERATURE (°C)

OFFSET VOLTAGE (mV)

0.5

1.5

1.0

2.0

2.5

-3 -1 0-2 1 2 3

OUTPUT VOLTAGE vs.

DIFFERENTIAL INPUT VOLTAGE

DIFFERENTIAL INPUT VOLTAGE (mV)

OUTPUT VOLTAGE (V)

MAX9010–13 toc12

TA = +25°C

TA = +85°C

TA = -40°C

0.2

0.3

0.5

0.4

0.6

0.7

-40 10 35-15 60 85

INPUT BIAS CURRENT vs. TEMPERATURE

MAX9010–13 toc11

TEMPERATURE (°C )

INPUT BIAS CURRENT (µA)

VCM = -0.2V

VCM = 3.1V

SUPPLY CURRENT vs. SUPPLY VOLTAGE

(PER COMPARATOR)

MAX9010–13 toc10

VCC (V)

ICC (mA)

5.755.505.255.004.75

0.5

1.0

1.5

2.0

2.5

3.0

4.50 6.00

TA = +85°CTA = +25°C

TA = -40°C

MAX9010–MAX9013

SC70, 5ns, Low-Power, Single-Supply,

Precision TTL Comparators

_______________________________________________________________________________________ 7

Detailed Description

These high-speed comparators have a unique design

that prevents oscillation when the comparator is in its

linear region, so no minimum input slew rate is required.

Many high-speed comparators oscillate in their linear

region. One common way to overcome this oscillation is

to add hysteresis, but it results in a loss of resolution

and bandwidth.

Latch Function

The MAX9011/MAX9013 provide a TTL-compatible latch

function that holds the comparator output state (Figure 1).

With LE driven to a TTL low or grounded, the latch is

transparent and the output state is determined by the

input differential voltage. When LE is driven to a TTL high,

the existing output state is latched, and the input differen-

tial voltage has no further effect on the output state.

Input Amplifier

A comparator can be thought of as having two sec-

tions: an input amplifier and a logic interface. The input

amplifiers of these devices are fully differential, with

input offset voltages typically 0.7mV at +25°C. Input

common-mode range extends from 200mV below

ground to 1.9V below the positive power-supply rail. The

total common-mode range is 3.3V when operating from a

5V supply. The amplifiers have no built-in hysteresis. For

highest accuracy, do not add hysteresis. Figure 2 shows

how hysteresis degrades resolution.

Input Voltage Range

Although the common-mode input voltage range is

restricted to -0.2V to (VCC - 1.9V), either or both inputs

can go to either absolute maximum voltage limit, i.e.,

from -0.3V to (VCC + 0.3V), without damage. The com-

parator will make a correct (and fast) logic decision

provided that at least one of the two inputs is within the

specified common-mode range. If both inputs are out-

side the common-mode range, the comparator output

state is indeterminate.

Resolution

A comparator’s ability to resolve a small-signal differ-

ence, its resolution, is affected by various factors. As

with most amplifiers and comparators, the most signifi-

cant factors are the input offset voltage (VOS) and the

common-mode and power-supply rejection ratios

(CMRR, PSRR). If source impedance is high, input off-

set current can be significant. If source impedance is

unbalanced, the input bias current can introduce

another error. For high-speed comparators, an addi-

MAX9010 MAX9011 MAX9012 MAX9013 NAME FUNCTION

11—7 OUT Comparator Output. OUT is high when IN+ is more

positive than IN-.

2 2 5 6 GND Ground

33—2 IN+ Noninverting Input

44—3 IN- Inverting Input

5, 6 6 8 1 VCC

Positive Power-Supply Voltage. Pins 5 and 6 of the

MAX9010 must BOTH be connected to the power-

supply rail. Bypass with a 0.1µF capacitor.

—5—5 LE Latch Enable Input

—— 1—INA+ Noninverting Input, Channel A

—— 2—INA- Inverting Input, Channel A

—— 3—INB+ Noninverting Input, Channel B

—— 4—INB- Inverting Input, Channel B

—— 6—OUTB Comparator Output, Channel B

—— 7—OUTA Comparator Output, Channel A

——— 4 N.C. No Connection. Not internally connected. Connect to

GND for best results.

——— 8OUT Comparator Complementary Output

Pin Description

MAX9010–MAX9013

SC70, 5ns, Low-Power, Single-Supply,

Precision TTL Comparators

8 _______________________________________________________________________________________

tional factor in resolution is the comparator’s stability in

its linear region. Many high-speed comparators are

useless in their linear region because they oscillate.

This makes the differential input voltage region around

zero unusable. Hysteresis helps to cure the problem

but reduces resolution (Figure 2). The devices do not

oscillate in the linear region and require no hysteresis,

which greatly enhances their resolution.

Applications Information

Power Supplies, Bypassing, and

Board Layout

These products operate over a supply voltage range of

4.5V to 5.5V. Bypass VCC to GND with a 0.1µF surface-

mount ceramic capacitor. Mount the ceramic capacitor

as close as possible to the supply pin to minimize lead

inductance.

As with all high-speed components, careful attention to

board layout is essential for best performance. Use a

PC board with an unbroken ground plane. Pay close

attention to the bandwidth of bypass components and

place them as close as possible to the device.

Minimize the trace length and area at the comparator

inputs. If the source impedance is high, take the utmost

care in minimizing its susceptibility to pickup of unwant-

ed signals.

Input Slew Rate

Most high-speed comparators have a minimum input

slew-rate requirement. If the input signal does not

transverse the region of instability within a propagation

delay of the comparator, the output can oscillate. This

makes many high-speed comparators unsuitable for

processing either slow-moving signals or fast-moving

signals with low overdrive. The design of these devices

eliminates the minimum input slew-rate requirement.

They are excellent for circuits from DC up to 200MHz,

even with very low overdrive, where small signals need

to be resolved.

Figure 1. Timing Diagram

tSU

tPD+

VIN

(DIFFERENTIAL)

LATCH

ENABLE (LE)

OUT

Figure 2. Effect of Hysteresis on Input Resolution

HYSTERESIS

BAND*

WITH HYSTERESIS

IDEAL (WITHOUT HYSTERESIS)

* WHEN HYSTERESIS IS ADDED, A COMPARATOR CANNOT RESOLVE ANY INPUT SIGNAL WITHIN THE HYSTERESIS BAND.

OUT

IN-

IN+

Chip Information

MAX9010 TRANSISTOR COUNT: 106

MAX9011 TRANSISTOR COUNT: 137

MAX9012 TRANSISTOR COUNT: 212

MAX9013 TRANSISTOR COUNT: 145

PROCESS: Bipolar

MAX9010–MAX9013

SC70, 5ns, Low-Power, Single-Supply,

Precision TTL Comparators

_______________________________________________________________________________________ 9

Package Information

SC70, 6L.EPS

Selector Guide

PART COMPARATORS LATCH COMPLEMENTARY

OUTPUTS

MAX9010 1 No No

MAX9011 1 Yes No

MAX9012 2 No No

MAX9013 1 Yes Yes

MAX9010–MAX9013

SC70, 5ns, Low-Power, Single-Supply,

Precision TTL Comparators

10 ______________________________________________________________________________________

Package Information (continued)

6LSOT.EPS

MAX9010–MAX9013

SC70, 5ns, Low-Power, Single-Supply,

Precision TTL Comparators

______________________________________________________________________________________ 11

Package Information (continued)

8LUMAXD.EPS

MAX9010–MAX9013

SC70, 5ns, Low-Power, Single-Supply,

Precision TTL Comparators

Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are

implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.

12 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600

Package Information (continued)

SOICN.EPS

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Maxim Integrated:

MAX9012EUA+ MAX9010EXT+T MAX9011EUT+T MAX9012ESA+ MAX9012ESA+T MAX9012EUA+T

MAX9013ESA+ MAX9013ESA+T MAX9013EUA+ MAX9013EUA+T MAX9012EUA MAX9012EUA-T MAX9013ESA

MAX9013ESA-T MAX9013EUA MAX9013EUA-T