5962-8766101XA - E2V Technologies (UK), Ltd.

QP27C128

April 7, 2009

2945 Oakmead Village Ct, Santa Clara, CA 95051 • Phone: (408) 737-0992 • Fax: (408) 736—8708 • Internet: www.qpsemi.com

QP27C128 – 128 Kilobit (16K x 8) CMOS EPROM

General Description

The QP27C128 is a 16Kx8 (128-Kbit), UV erasable programmable read-only memory. It operates from a single +5 V

supply, has a static standby mode, and features fast single address location programming. The QP27C128 meets the

same specification requirements and utilizes the same programming methodology as the AMD 27C128 that it replaces.

Products are available in windowed and non-windowed (OTP) ceramic hermetic packages, as well as plastic one time

programmable (OTP) packages.

Data is typically accessed in less than 45 ns, allowing high-performance microprocessors to operate without any WAIT

states. The device offers separate Output Enable ( OE ) and Chip Enable ( CE ) pins, eliminating bus contention in a

multiple bus system.

Typical power consumption is only 80 mW in active mode, and 100 μW in standby mode.

All signals are TTL levels, including programming signals. Bit locations may be programmed singly, in blocks, or at

random. The device is programmed identically to the AMD27C128 device that it replaces, using the same programming

algorithm (100 us pulses).

The QP27C128 features:

- Same programming algorithm as the AMD27C128, allowing it to be programmed using the same equipment,

data and algorithm. When programming this device select AMD as the manufacturer and 27C128 as the

devicetype.

- Speed options as fast as 45ns

- JEDEC Pinout

- Single +5V power supply

- CMOS and TTL input/output compatibility

- Two line control functions

The device/family is constructed using an advanced UV CMOS wafer fabrication process.

Block Diagram

QP27C128

QP SEMI, 2945 Oakmead Village Court, Santa Clara, CA 95051 Page 2 of 9

Pin Name Function

A0 – A13 Address Inputs

CE (E) Chip Enable Input

DQ0 – DQ7 Data Input/Output

OE (G) Output Enable Input

PGM (P) Program Enable Input

VCC V

CC Supply Voltage

VPP Program Voltage Input

Connection Diagrams

CERDIP / CERPACK / PDIP LCC / PLCC

Device Type

Functional Description

Device Erasure

In order to clear all locations of their programmed contents, the device must be exposed to an ultraviolet light source. A

dosage of 15 W seconds/cm2 is required to completely erase the device. This dosage can be obtained by exposure to

an ultraviolet lamp with a wavelength of 2537Å and an intensity of 12,000 μW/cm2 for 15 to 20 minutes. The device

should be directly under and about one inch from the source, and all filters should be removed from the UV light source

prior to erasure.

Note that all UV erasable devices will erase with light sources having wavelengths shorter than 4000Å, such as

fluorescent light and sunlight. Although the erasure process happens over a much longer time period, exposure to any

light source should be prevented for maximum system reliability. Simply cover the package window with an opaque

label or substance.

Device Programming

Upon delivery, or after each erasure, the device has all of its bits in the “ONE”, or HIGH state. “ZEROs” are loaded into

the device through the programming procedure.

The device enters the programming mode when 12.75V ± 0.25V is applied to the VPP pin, and both CE & PGM are at

VIL.

For programming, the data to be programmed is applied 8 bits in parallel to the data pins.

The programming algorithm uses a 100 μs programming pulse and gives each address only as many pulses as needed

QP27C128

QP SEMI, 2945 Oakmead Village Court, Santa Clara, CA 95051 Page 3 of 9

to reliably program the data. After each pulse is applied to a given address, the data in that address is verified. If the

data does not verify, additional pulses are given until it verifies or the maximum pulses allowed is reached. This process

is repeated while sequencing through each address of the device. This part of the algorithm is done with VCC = 6.25 V to

assure that each bit is programmed to a sufficiently high threshold voltage. After the final address is completed, the

entire EPROM memory is verified at VCC = VPP = 5.25 V.

Program Inhibit

Programming different data to multiple devices in parallel is easily accomplished. Except for CE , all like inputs of the

devices may be common. A TTL low-level program pulse applied to one device’s CE input with VPP = 12.75 V ± 0.25 V

and PGM LOW will program that particular device. A high-level CE input inhibits the other devices from being

programmed.

Program Verify

Verification should be performed on the programmed bits to determine that they were correctly programmed. Verify

should be performed with OE and CE at VIL, PGM at VIH, and VPP between 12.5 V and 13.0 V.

Autoselect Mode

The autoselect mode provides manufacturer and device identification through identifier codes on DQ0–DQ7. This mode

is primarily intended for programming equipment to automatically match a device to be programmed with its

corresponding programming algorithm. This mode is functional in the 25°C ± 5°C ambient temperature range that is

required when programming the device. To activate this mode, the programming equipment must force VH on address

line A9. Two identifier bytes may then be sequenced from the device outputs by toggling address line A0 from VIL to VIH

(that is, changing the address from 00h to 01h). All other address lines must be held at VIL during the autoselect mode.

Byte 0 (A0 = VIL) represents the manufacturer code, and Byte 1 (A0 = VIH), the device identifier code. Both codes have

odd parity, with DQ7 as the parity bit.

Read Mode

To obtain data at the device outputs, Chip Enable ( CE ) and Output Enable ( OE ) must be driven low. CE controls the

power to the device and is typically used to select the device. OE enables the device to output data, independent of

device selection. Addresses must be stable for at least tACC–tOE.

Standby Mode

The device enters the CMOS standby mode when CE is at VCC ± 0.3 V. Maximum VCC current is reduced to 100 μA.

The device enters the TTL-standby mode when CE is at VIH. Maximum VCC current is reduced to 1.0 mA. When in

either standby mode, the device places its outputs in a high-impedance state, independent of the OE input.

Output OR Connection

To accommodate multiple memory connections, a two-line control function provides:

• Low memory power dissipation

• Assurance that output bus contention will not occur.

CE should be decoded and used as the primary device selecting function, while OE be made a common connection

to all devices in the array and connected to the READ line from the system control bus. This assures that all deselected

memory devices are in their low-power standby mode and that the output pins are only active when data is desired from

a particular memory device.

System Applications

During the switch between active and standby conditions, transient current peaks are produced on the rising and falling

edges of Chip Enable. The magnitude of these transient current peaks is dependent on the output capacitance loading

of the device. As a minimum, a 0.1μF ceramic capacitor (high frequency, low inductance) should be used on each

device between VCC and VSS to minimize transient effects. In addition, to overcome the voltage drop caused by the

inductive effects of the printed circuit board traces on EPROM arrays, a 4.7μF bulk electrolytic capacitor should be used

between VCC and VSS for each eight devices. The location of the capacitor should be close to where the power supply is

connected to the array.

QP27C128

QP SEMI, 2945 Oakmead Village Court, Santa Clara, CA 95051 Page 4 of 9

MODE Select Table

Mode CE OE PGM A0 A9 VPP Outputs Notes

Read VIL V

IL X X X X DOUT \1

Output Disable X VIH X X X X High Z \1

Standby (TTL) VIH X X X X X High Z \1

Standby (CMOS) VCC±0.3V X X X X X High Z \1

Program VIL X VIL X X VPP DIN \1

Program Verify VIL V

IL V

IH X X VPP DOUT \1

Program Inhibit VIH X X X X VPP High Z \1

Manufacturer Code VIL V

IL X VIL V

H X 01h \1 \2 \3 \4

Device Code VIL V

IL X VIH V

H X 16h \1 \2 \3 \4

Notes:

\1 X = Either VIH or VIL

\2 VH = 12.0V ± 0.5V

\3 A1-A8 & A10-A12 = VIL

\4 Device Manufacture Code and Device ID match original AMD device for programming compatibility

Absolute Maximum Ratings

Stresses above the AMR may cause permanent damage, extended operation at AMR may degrade performance and affect reliability

Condition Units Notes

Power Supply (VCC) -0.6 to +6.25 Volts DC

Voltage with Respect to VSS

All pins except A9, VPP, VCC -0.6 to +6.25 Volts \5 \9

9 -0.6 to +13.5 Volts \6 \9

PP -0.6 to +14 Volts \6 \9

Storage Temperature Range -65 to +150 ºC \7

Lead Temperature (soldering, 10 seconds) +300 ºC

Junction Temperature (TJ) +150 ºC \7

Maximum Operating Temperature

Commercial Devices 0 to 70 ºC \7 \8

Industrial Devices -40 to 85 ºC \7 \8

Military Temperature Range -55 to 125 ºC \7 \8

Data Retention 10 Years, minimum

Device must not be removed from or inserted into a socket when VCC or VPP is applied.

Recommended Operating Conditions

Condition Units Notes

Supply Voltage Range (VCC) 4.5 to 5.5 Volts DC

Input or Output Voltage Range 0.0 to VCC Volts DC \5 \6

Minimum High-Level Input Voltage (VIH TTL) 2.0 Volts DC

Minimum High-Level Input Voltage (VIH CMOS) VCC ± 0.2 Volts DC

Maximum Low-Level Input Voltage (VIL TTL) 0.8 Volts DC

Maximum Low-Level Input Voltage (VIL CMOS) GND ± 0.2 Volts DC

Case Operating Range (Tc)

Commercial Devices 0 to 70 ºC \7 \8

Industrial Devices -40 to 85 ºC \7 \8

QP27C128

QP SEMI, 2945 Oakmead Village Court, Santa Clara, CA 95051 Page 5 of 9

Military Temperature Range -55 to 125 ºC \7 \8

\5 – Minimum DC Input Voltage on input or I/O pins –0.5V. During voltage transitions, the input may overshoot VSS to

–2.0V for periods of up to 20ns. Maximum DC voltage on input and I/O pins is VCC+0.5V. During transitions,

input and I/O pins may overshoot to VCC +2.0V for periods up to 20ns.

\6 – Minimum DC Input Voltage on A9 is –0.5V. During voltage transitions, A9 and VPP may overshoot VSS to –2.0V

for periods of up to 20ns. A9 and VPP must not exceed +13.5V at any time.

\7 – Do not exceed 125ºC TC or TJ for plastic package devices.

\8 – Maximum PD, Maximum TJ Are Not to Be Exceeded.

\9 – During transitions, the inputs may undershoot to –2.0 V dc for periods less than 20 ns.

\10 – VPP may be connected directly to VCC except during programming.

\11 – Qualification Only.

\12 – If not tested, shall be guaranteed to the limits specified.

\13 – For all switching characteristics and timing measurements, input pulse levels are 0.4V and 2.4V and VPP = 12.5 ±

0.5V during programming.

TABLE I – ELECTRICAL PERFORMANCE CHARACTERISTICS

Test Symbol Conditions

-55ºC ≤TA≤+125ºC

Unless Otherwise Specified

Min Max Unit

Output High Voltage VOH V

IL=0.8V,VIH=2.0V

IOL= -400 μA

2.4 V

Output Low Voltage VOL V

IL=0.8V,VIH=2.0V

IOL= 2.1mA 0.45 V

Input Current (Leakage) II V

I = 5.5V or 0.0V

All other inputs at either VCC or GND -10.0 +10.0 μA

Output Current (Leakage) IO V

O = 5.5V or 0.0V -10.0 +10.0 μA

VPP Supply Current IPP1 V

PP = VCC = 5.5V 100 μA

VPP Supply Current (during IPP2 V

PP = 13V All but 70ns 50 mA

program pulse) \12 70ns 60 mA

Operating Current (active) ICC1 V

CC = 5.5V 70ns 85 mA

CE (E) = VIL 90ns 70 mA

f = 1/tAVQV 120ns 60 mA

0-O7 = 0 mA 150ns 25 mA

170ns 25 mA

200ns 25 mA

250ns 25 mA

300ns 25 mA

QP27C128

QP SEMI, 2945 Oakmead Village Court, Santa Clara, CA 95051 Page 6 of 9

TABLE I – ELECTRICAL PERFORMANCE CHARACTERISTICS

Test Symbol Conditions

-55ºC ≤TA≤+125ºC

Unless Otherwise Specified

Min Max Unit

Standby Current, TTL ICC2 V

CC = 5.5V 70ns 200 mA

CE (E) =2.0Vdc 90ns 3.0 mA

f = 0hz 120ns 3.0 mA

150ns 3.0 mA

170ns 3.0 mA

200ns 3.0 mA

250ns 3.0 mA

300ns 3.0 mA

Standby Current, CMOS ICC3 V

CC = 5.5V 70ns 300 μA

CE (E) = VCC 90ns 300 μA

f = 0Hz 120ns 300 μA

150ns 300 μA

170ns 300 μA

200ns 300 μA

250ns 300 μA

300ns 500 μA

Input Capacitance \11 CIN V

IN = 0V, f = 1 MHz 10 pF

Output Capacitance \11 COUT V

OUT = 0V, f = 1 MHz 14 pF

Address to Output Delay TAVQV 70ns 70 ns

\13 90ns 90 ns

120ns 120 ns

150ns 150 ns

170ns 170 ns

200ns 200 ns

250ns 250 ns

300ns 300 ns

QP27C128

QP SEMI, 2945 Oakmead Village Court, Santa Clara, CA 95051 Page 7 of 9

TABLE I – ELECTRICAL PERFORMANCE CHARACTERISTICS

Test Symbol Conditions

-55ºC ≤TA≤+125ºC

Unless Otherwise Specified

Min Max Unit

Chip enable access time TELQV 70ns 70 ns

\13 90ns 90 ns

120ns 120 ns

150ns 150 ns

170ns 170 ns

200ns 200 ns

250ns 250 ns

300ns 300 ns

Output enable access time TOLQV 70ns 25 ns

\13 90ns 50 ns

120ns 50 ns

150ns 70 ns

170ns 70 ns

200ns 75 ns

250ns 100 ns

300ns 120 ns

CE or OE disable to TEHQZ, 70ns 25 ns

output in high Z TOHQZ 90ns 50 ns

\12 120ns 50 ns

150ns 50 ns

170ns 50 ns

200ns 60 ns

250ns 60 ns

300ns 105 ns

CE or OE enable to TEHQV, 70ns 0 ns

output valid TOHQV 90ns 0 ns

\12 120ns 0 ns

150ns 0 ns

170ns 0 ns

200ns 0 ns

250ns 0 ns

300ns 0 ns

QP27C128

QP SEMI, 2945 Oakmead Village Court, Santa Clara, CA 95051 Page 8 of 9

Ordering Information

Part Number Package (Mil-Std-1835) Generic

5962-8766101XA GDIP1-T28 CDIP2-T28 (DIP) QP27C128-90/XA

5962-8766101YA CQCC1-N32 (LCC) QP27C128-90/YA

5962-8766101YC CQCC1-N32 (LCC) QP27C128-90/YC

5962-8766102XA GDIP1-T28 CDIP2-T28 (DIP) QP27C128-120/XA

5962-8766102YA CQCC1-N32 (LCC) QP27C128-120/YA

5962-8766102YC CQCC1-N32 (LCC) QP27C128-120/YC

5962-8766103XA GDIP1-T28 CDIP2-T28 (DIP) QP27C128-150/XA

5962-8766103YA CQCC1-N32 (LCC) QP27C128-150/YA

5962-8766103YC CQCC1-N32 (LCC) QP27C128-150/YC

5962-8766104XA GDIP1-T28 CDIP2-T28 (DIP) QP27C128-170/XA

5962-8766104YA CQCC1-N32 (LCC) QP27C128-170/YA

5962-8766104YC CQCC1-N32 (LCC) QP27C128-170/YC

5962-8766105XA GDIP1-T28 CDIP2-T28 (DIP) QP27C128-200/XA

5962-8766105YA CQCC1-N32 (LCC) QP27C128-200/YA

5962-8766105YC CQCC1-N32 (LCC) QP27C128-200/YC

5962-8766106XA GDIP1-T28 CDIP2-T28 (DIP) QP27C128-250/XA

5962-8766106YA CQCC1-N32 (LCC) QP27C128-250/YA

5962-8766106YC CQCC1-N32 (LCC) QP27C128-250/YC

5962-8766107XA GDIP1-T28 CDIP2-T28 (DIP) QP27C128-300/XA

5962-8766107YA CQCC1-N32 (LCC) QP27C128-300/YA

5962-8766107YC CQCC1-N32 (LCC) QP27C128-300/YC

5962-8766108YA CQCC1-N32 (LCC) QP27C128-70/YA

QP Semiconductor supports Source Control Drawing (SCD), and custom package development for this product family.

QP27C128

QP SEMI, 2945 Oakmead Village Court, Santa Clara, CA 95051 Page 9 of 9

Notes:

Package outline information and specifications are defined by Mil-Std-1835 package dimension require ments.

“-MIL” products manufactured by QP Semiconductor are compliant to the assembly, burn-in, test and quality conformance

requirements of Test Methods 50 04 & 5005 of Mil-Std-883 for Class B devices. This datasheet defines the electrical test

requirements for the device(s) .

The listed drawings, Mil-PRF-38535, Mil-Std-88 3 and Mil-Std-1835 are available online at http://www.dscc.dla.mil/

Additional information is available at our website http://www.qpsemi.com