PTV03020 3.3 Vin single output DC-DC CONVERTERS * * * * * * * * * * * * POLA Non-isolated 1 NEW Product 18 A output current 3.3 Vin input voltage Wide-output voltage adjust (0.8 Vdc to 2.5 Vdc) Auto-trackTM sequencing* Pre-bias start-up Efficiencies up to 96% Output ON/OFF inhibit Output voltage sense Vertical through-hole mounting Point-of-Load-Alliance (POLA) compatible Undervoltage lockout Available RoHS compliant The PTV03020 is a non-isolated dc-dc converter from Artesyn under the Point of Load Alliance (POLA) standard. The vertical mounting option of the PTV03020 module provides performance in less than 20% of the space that is required by alternative solutions. The Auto-TrackTM feature provides for sequencing between multiple modules, a function, which is becoming a necessity for powering advanced silicon including DSP's, FPGA's and ASIC's requiring controlled power-up and power-down. The PTV03020 has an input voltage of 2.95 Vdc to 3.6 Vdc and offers a wide 0.8 Vdc to 2.5 Vdc output voltage range with up to 18 A output current, which allows for maximum design flexibility and a pathway for future upgrades. 2 YEAR WARRANTY All specifications are typical at nominal input, full load at 25 C unless otherwise stated Cin = 680 F and 22 F(Ceramic), Cout = 0 F OUTPUT SPECIFICATIONS GENERAL SPECIFICATIONS Voltage adjustability (See Note 4) 0.8-2.5 Vdc Setpoint accuracy (See Note 8) 2.0% Vo Efficiency Line regulation 5 mV typ. Load regulation 5 mV typ. Approvals and standards (See Note 8) Minimum load Ripple and noise 0A 20 MHz bandwidth Temperature co-efficient -40 C to +85 C Transient response (See Note 5) 3.0% Vo 20 mV pk-pk 0.5% Vo 70 s recovery time Overshoot/undershoot 120 mV Non-isolated 250-340 kHz 300 kHz typ. EN60950 UL/cUL60950 Material flammability Dimensions UL94V-0 (L x W x H) 44.45 x 9.39 x 12.70 mm 1.75 x 0.37 x 0.50 in Weight MTBF 96% max. 5.5 g (0.19 oz) Telcordia SR-332 5,000,000 hours ENVIRONMENTAL SPECIFICATIONS INPUT SPECIFICATIONS Input voltage range (See Efficiency Table) Insulation voltage Switching frequency Total regulation SPECIFICATIONS (See Note 3) Input standby current 2.95-3.6 Vdc Thermal performance (See Note 2) 10 mA typ. Positive logic Remote ON/OFF (See Note 1) Undervoltage lockout (Increasing) 2.7 V typ. Overcurrent Track input current Pin 9 (See Notes 6, 7) -0.13 mA Overtemperature Operating ambient, temperature Non-operating -40 C to +85 C -40 C to +125 C PROTECTION Auto reset 35 A typ. Auto recovery International Safety Standard Approvals UL/cUL CAN/CSA-C22.2 No. 60950 File No. E174104 *Auto-trackTM is a trade mark of Texas Instruments TUV Product Service (EN60950) Certificate No. B 04 06 38572 044 CB Report and Certificate to IEC60950, Certificate No. US/8292/UL File Name: ptv03020w.pdf Rev (02): 19 Dec 2005 PTV03020 3.3 Vin single output DC-DC CONVERTERS POLA Non-isolated 2 For the most current data and application support visit www.artesyn.com/powergroup/products.htm NEW Product OUTPUT POWER (MAX.) INPUT VOLTAGE OUTPUT VOLTAGE OUTPUT CURRENT (MIN.) OUTPUT CURRENT (MAX.) (2) EFFICIENCY (MAX.) LINE LOAD MODEL NUMBER (9,10) 45 W 2.95-3.6 Vdc 0.8-2.5 Vdc 0A 18 A 96% 5 mV 5 mV PTV03020W Part Number System with Options REGULATION PTV03020WAH Product Family Point of Load Alliance Compatible Mounting Version V = Vertical Input Voltage 03 = 3.3 V Mounting Style (9) D = Horizontal Through-Hole (Matte Sn) H = Horizontal Through-Hole (Sn/Pb) Pin Style A = Through-Hole Std. Pin Length (0.150") Output Voltage Code W = Wide Output Current 02 = 18 A Mechanical Package Always 0 Output Voltage Adjustment of the PTV03020 Series The ultra-wide output voltage trim range offers major advantages to users who select the PTV03020. It is no longer necessary to purchase a variety of modules in order to cover different output voltages. The output voltage can be trimmed in a range of 0.8 Vdc to 2.5 Vdc. When the PTV03020 converter leaves the factory the output has been adjusted to the default voltage of 0.8 V Notes Remote ON/OFF. Positive logic ON: Pin 3 open; or V > Vin - 0.5 V OFF: Pin 3 GND; or V < 0.6 V 2 See Figure 1 for safe operating curve. 3 A 680 F electrolytic input capacitor is required for proper operation as well as a 2 2F high-frequency ceramic capacitor. The electrolytic capacitor must be rated for a minimum of 750 mA rms of ripple current. 4 An external output capacitor is not required for basic operation. Adding 33 0F of distributed capacitance at the load will improve the transient response. 5 1A/s load step, 50 to 100% Iomax, C3 = 330 F. 6 If utilized Vout will track applied voltage by 0.3 V (up to Vo set point). 7 The pre-bias start-up feature is not compatible with Auto-TrackTM. This is because when the module is under Auto-TrackTM control, it is fully active and will sink current if the output voltage is below that of a back-feeding source. Therefore to ensure a pre-bias hold-off, one of the following two techniques must be followed when input power is first applied to the module. The Auto-TrackTM function must either be disabled, or the module's output held off using the Inhibit pin. Refer to Application Note 197 for more details. 8 The set-point voltage tolerance is affected by the tolerance and stability of Rset. The stated limit is unconditionally met if Rset has a tolerance of 1% with 100/C or better temperature stability. 9 To order Pb-free (RoHS compatible) through-hole parts replace the mounting option `H' with `D', e.g. PTV03020WAD. 10 NOTICE: Some models do not support all options. Please contact your local Artesyn representative or use the on-line model number search tool at http://www.artesyn.com/powergroup/products.htm to find a suitable alternative. EFFICIENCY TABLE (IO = 12 A) 1 OUTPUT VOLTAGE EFFICIENCY Vo = 2.5 V 95 Vo = 1.8 V 92 Vo = 1.5 V 90 Vo = 1.2 V 88 Vo = 1.0 V 86 Vo = 0.8 V 83 File Name: ptv03020w.pdf Rev (02): 19 Dec 2005 PTV03020 3.3 Vin single output DC-DC CONVERTERS POLA Non-isolated 3 For the most current data and application support visit www.artesyn.com/powergroup/products.htm NEW Product 90 100 70 60 400 LFM 200 LFM 100 LFM Nat conv 50 40 30 EFFICIENCY (%) TEMPERATURE (C) 80 90 Vout 2.5V 1.5V 1.0V 0.8V 80 70 60 50 20 0 0 3 6 9 12 OUTPUT CURRENT (A) 15 3 6 9 12 15 18 18 OUTPUT CURRENT (A) Figure 1 - Safe Operating Area Vin = 3.3 V, Output Voltage = 2.5 V (See Note A) Figure 2 - Efficiency vs Load Current Vin = 3.3 V (See Note B) Notes Vo Sense A SOA curves represent the conditions at which internal components are within the Artesyn derating guidelines. B Characteristic data has been developed from actual products tested at 25 C. This data is considered typical data for the converter. Track 7 Sense 9 Track 5, 6 Vin Vin PTVxx020 Inhibit 12 10. 11 Inhibit C1 680uF (Required) C2 22uF Ceramic (Required) GND 1, 2 3, 4 Vo Vo Vo Adj 8 Rset 1% 0.05W L O A D C3 330uF Optional GND GND Figure 3 - Standard Application File Name: ptv03020w.pdf Rev (02): 19 Dec 2005 PTV03020 3.3 Vin single output DC-DC CONVERTERS POLA Non-isolated 4 For the most current data and application support visit www.artesyn.com/powergroup/products.htm SIDE VIEW NEW Product FRONT VIEW 0.370 (9.39) MAX. PCB 1.750 (44.45) 0.500 (12.7) 0.150 (3.81) 0.640 (16.26) 0.025 (0.64) Min 12 Places Plated Through Hole 1 2 3 4 5 6 7 8 9 10 11 12 0.050 (1.27) 0.650 (16.51) 0.020 (0.51) TYP. 0.100 (2.54) TYP. Dimensions in Inches (mm) Tolerances (unless otherwise specified) 2 Places 0.030 (0.76) 3 Places 0.010 (0.25) PIN CONNECTIONS PIN NO. FUNCTION 1 Ground 2 Ground 3 Vout 4 Vout 5 Vin 6 Vin 7 Vo Sense 8 Vo Adjust 9 Track 10 Ground 11 Ground 12 Inhibit Figure 4 - Mechanical Drawing and Pinout Table Datasheet (c) Artesyn Technologies(R) 2005 The information and specifications contained in this datasheet are believed to be correct at time of publication. However, Artesyn Technologies accepts no responsibility for consequences arising from printing errors or inaccuracies. The information and specifications contained or described herein are subject to change in any manner at any time without notice. No rights under any patent accompany the sale of any such product(s) or information contained herein. Please consult our website for the following items: 4 Application Note www.artesyn.com File Name: ptv03020w.pdf Rev (02): 19 Dec 2005