2017 Microchip Technology Inc. DS20005850B-page 1
PAC1934
Features
• High-Side Current Monitor
- 100 mV full scale range for current sense
voltage,16b resolution default setting
- Selectable bidirectional current sense capa-
bility, –100 mV to +100 mV range, 16-bit
two’s complement (signed) data format
- External sense resistor sets full scale current
range
- Very low input current simplifies routing
• Wide Bus Voltage Range for Voltage Monitor
- 0V to 32V input common-mode voltage
- 16-bit resolution for voltage measurements,
14b are used for power calculations
• Real Time Auto-Calibration of Offset and Gain
Errors for Voltage and Current, No User Adjust-
ment Required
• 1% Power Measurement Accuracy over a Wide
Dynamic Range
• On-Chip Accumulation of 28-bit Power Results for
Energy Measurement
- 48-bit power accumulator register for record-
ing accumulated power data
- 24 bit Accumulator Count
- User programmable sampling rates of 8, 64,
256 and 1024 samples per second
- 17 minutes of power data accumulation mini-
mum at 1024 S/s
- >36 hours of power data accumulation mini-
mum at 8 S/s
• 2.7V to 5.5V Supply Operation
- Separate VDD I/O pin for digital I/O
- 1.62-5.5V capable SMBus and digital I/O
- SMBus 3.0 and I2C Fast Mode Plus (1Mb/S)
• SMBus Address - 16 Options, set with Resistor
• No Input Filters Required
• ALERT Features that can be Enabled:
- ALERT on accumulator overflow
- ALERT on Conversion Complete
• 2.225 x 2.17 mm WLCSP Package
Applications
• Notebook and Tablet Computing
•Networking
• Automotive
• Cloud, Linux and Server Computing
• Industrial
• Linux Applications
Description
The PAC1934 device is a four-channel energy monitor,
with bus voltage monitor and current sense amplifiers that
feed high-resolution ADCs. Digital circuitry performs power
calculations and energy accumulation.
This enables energy monitoring with integration periods
from 1 ms up to 36 hours or longer. Bus voltage, sense
resistor voltage and accumulated proportional power are
stored in registers for retrieval by the system master or
Embedded Controller.
The sampling rate and energy integration period can be
controlled over SMBus or I
2
C. Active channel selection,
one-shot measurements and other controls are also config-
urable by SMBus or I
2
C.
The PAC1934 uses real time calibration to minimize offset
and gain errors. No input filters are required for this device.
Package Types
PAC1934 – Top View
2.225 x 2.17 mm WLCSP
For more details, see Table 3-1 and Section 7.0.
A
B
C
D
123 4
SENSE1+SENSE1-SENSE2+
SENSE2-
SENSE3+
SENSE3-
SENSE4+SENSE4-
GND
SM_DATA
SM_CLK
VDD
VDD I/O
ADDRSEL
PWRDN
SLOW/ALERT
Four Channel DC Power/Energy Monitor with Accumulator
PAC1934
DS20005850B-page 2 2017 Microchip Technology Inc.
Device Block Diagram
VDD GND
VDD I/O
ADDRS EL
SLOW/ALERT
Accumlato r
Differen tia l
VSENS E
Amplifier
VBUS
Buffer/
Divi der
SM_CLK
SM_DATA
PWRDN
I2C/SMBus
ADC/MUX Clocking &
Control
VBUS
Registers
VSENS E
Registe rs
VPOWE R
Registe rs
Accumulator
Registe rs
Control
Registe rs
Calculation
and
Calibration
16-bit
ADC
16-bit
ADC
Resistor
Decoder
SENSE 1+
SENSE 1-
SENSE 2+
SENSE 2-
SENSE 3+
SENSE 3-
SENSE 4+
SENSE 4-
VBUS1
VBUS2
High
Voltage
MUX
VBUS4
Sense1+
Sense2+
Sense1-
Sense2-
Sense3+
Sense3-
Sense4+
Sense4-
VBUS3
2017 Microchip Technology Inc. DS20005850B-page 3
PAC1934
1.0 ELECTRICAL CHARACTERISTICS
1.1 Electrical Specifications
Absolute Maximum Ratings(†)
VDD pin...........................................................................................................................................................–0.3 to 6.0V
Voltage on SENSE- and SENSE+ pins...........................................................................................................–0.3 to 40V
Voltage on any other pin to GND ........................................................................................................GND –0.3 to +6.0V
Voltage between Sense pins (|(SENSE+ – SENSE–)|).........................................................................................500 mV
Input current to any pin except VDD ....................................................................................................................±100 mA
Output short-circuit current.............................................................................................................................. Continuous
Junction to Ambient (J-A)...................................................................................................................................+78°C/W
Operating Ambient Temperature Range .................................................................................................... –40 to +150°C
Storage Temperature Range...................................................................................................................... –55 to +150°C
ESD Rating – all pins – HBM...................................................................................................................................4000V
ESD Rating – all pins – CDM ..................................................................................................................................2000V
† Notice: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device.
This is a stress rating only and functional operation of the device at those or any other conditions above those indicated
in the operation listings of this specification is not implied. Exposure above maximum rating conditions for extended peri-
ods may affect device reliability.
ESD Protection Diagram
This diagram represents the ESD protection circuitry
on the PAC1934. These pins are allowed to be at 32V
if VDD is at zero. The back to back diodes between the
Sense+ and Sense– pins have 1 kΩ resistors in series
with them.
SM_DATA SM_CLK ADDRS EL VDD I/O VDD GND
CLAMP
CIRCUIT
SENSE 1-
SENSE 1+
(Floating ESD rail)
(~40v breakdown)
SENSE 2-
SENSE 2+
SENSE 3-
SENSE 3+
SENSE 4-
SENSE 4+
PWRDN
SLOW/
ALERT
PAC1934
DS20005850B-page 4 2017 Microchip Technology Inc.
TABLE 1-1: DC CHARACTERISTICS
Electrical Characteristics: Unless otherwise specified, maximum values are at TA = –40°C to +85°C,
VDD = 2.7V to 5.5V, VDD I/O= 1.62V to 5.5V, VBUS = 0V to 32V; typical values are at TA = +25°C
VDD = VDD I/O = 3.3V, VBUS = 32V, VSENSE = (SENSE+ – SENSE–) = 0V
Characteristic Symbol Min. Typ. Max. Unit Conditions
Power Supply
VDD Range VDD 2.7 — 5.5 V
VDD I/O Range VDD I/O 1.62 — 5.5 V
VDD Pin Active
Current
IDD — 585 675 µA All 4 measurement channels
enabled. 1024 Samples/s
VDD Pin Active
Current
IDD SLOW — 16 — µA 4 channels enabled, 8 Samples/s
Minimum VDD Rise
Rate
VDD_RISE_MIN — 0.05 — V/ms 0 to 5V in 100 ms
Maximum VDD Rise
Rate
VDD_RISE — 1000 — V/ms 0 to 5V in 5 µs
VDD Sleep Current IDD_SLEEP —5—µASleep State
VDD Power-Down
Current
IDD_PWRDN — 0.1 — µA Power-Down State
VDD I/O Current IDD I/O — — 2 µA All States
Analog Input Characteristics
VBUS Voltage Range VBUS –0.2V — 32 V Common mode range for SENSE+
and SENSE– pins, referenced to
ground (negative range not tested
in production)
VSENSE Differential
Input Voltage Range
VSENSE_DIF –100 — 100 mV
SENSE+, SENSE–
Pin Input Current
ISENSE +, ISENSE- –7 0 7 µA VSENSE+ = VSENSE– = 32V
(Input current is the combined cur-
rent for the two pins)
SENSE+, SENSE–
Pin Input current
ISENSE +, ISENSE- –1 0 1 µA VSENSE = 6V, VSENSE– = 5.9V
VSENSE Measurem en t Ac c ur a cy
VSENSE Gain
Accuracy
VSENSE_
GAIN_ERR
—±0.2
±1
±0.9 %
%
At +25°C
typical, –40 to +85°C
VSENSE Offset
Accuracy, referenced
to input
VBUS_
OFFSET_ERR
— ±0.02
±0.2
±0.1 mV
mV
At +25C°
typical, –40 to +85°C
VSENSE – Unidirectional Currents
VSENSE
ADC Resolution
VSENSE_RES — — 16 Bits Straight Binary for unidirectional
currents
VSENSE
Full Scale Range
VSENSE_FSR 0 — 100 mV Unidirectional currents
VSENSE LSB Step
Size
VSENSE_LSB — 1.5 — µV Unidirectional currents
VSENSE – Bidirectional Currents
VSENSE
ADC Resolution
VSENSE_RES — — 16 bits 16-bit two’s complement (signed)
VSENSE
Full Scale Range
VSENSE_FSR –100 — 100 mV Bidirectional currents
2017 Microchip Technology Inc. DS20005850B-page 5
PAC1934
VSENSE LSB Step
Size
VSENSE_LSB — 3 — µV Bidirectional currents
VBUS Measurement Accuracy
VBUS Gain Accuracy VBUS_GAIN_ERR — ±0.02
±0.2
±0.5 %
%
At +25°C
typical, –40 to +85°C
VBUS Offset Accu-
racy, referenced to
input
VBUS_
OFFSET_ERR
—±1
±2
—LSB
LSB
At +25°C
typical, –40 to +85°C
VBUS – Unipolar Voltages
VBUS
ADC Resolution
VBUS_RES — — 16 bits Straight Binary for unidirectional
currents
VBUS Unipolar
Full-Scale Range
VBUS_FSR 0 — 32 V Unipolar voltage
VBUS LSB Step Size VBUS_LSB — 488 — µV FSR = 32V, 16-bit resolution
VBUS – Bipolar Voltages
VBUS ADC Resolution VBUS_RES — — 16 bits 16-bit two's complement (signed)
numbers are reported for VBUS
measurement result
VBUS Bipolar
Full-Scale Range
VBUS_FSR –32 — 32 V Mathematical scaling.
Physics limits the negative input
voltage to –0.2V
VBUS LSB Step Size VBUS_LSB — 976 — µV Bipolar voltages
TABLE 1-1: DC CHARACTERISTICS (CONTINUED)
Electrical Characteristics: Unless otherwise specified, maximum values are at TA = –40°C to +85°C,
VDD = 2.7V to 5.5V, VDD I/O= 1.62V to 5.5V, VBUS = 0V to 32V; typical values are at TA = +25°C
VDD = VDD I/O = 3.3V, VBUS = 32V, VSENSE = (SENSE+ – SENSE–) = 0V
Characteristic Symbol Min. Typ. Max. Unit Conditions
PAC1934
DS20005850B-page 6 2017 Microchip Technology Inc.
Power Accumulator Accuracy
Accumulator Error ACC_Err —0.2—%V
SENSE = 97 mV
Accumulator Error ACC_Err —0.2—%V
SENSE = 10 mV
Accumulator Error ACC_Err —1—%V
SENSE = 1 mV
Accumulator Error ACC_Err —3—%V
SENSE = 100 µV
Accumulator Error ACC_Err —5—%V
SENSE = 50 µV
Active Mode Timing
Pull-Up Voltage
Range
VPULLUP 1.62 — 5.5 V Pull-up voltage for I2C/SMBus pins
and digital I/O pins. Set by VDD I/O.
Time to First
Communications
tINT_T — 14.25 — ms
Transition From Sleep
State to Start of
Conversion Cycle
tSLEEP_TO_ACTIVE —3—ms
Digital I/O Pins (SM_CLK, SM_DATA, SLOW/ALERT, PWRDN)
Input High Voltage VIH VDD I/O
x 0.7
——V
Input Low Voltage VIL ——V
DD I/O
x 0.3
V
Output Low Voltage VOL — — 0.4 V Sinking 8 mA for the ALERT pin
and 20 mA for the SMCLK pin
Leakage Current ILEAK –1 — +1 µA
TABLE 1-1: DC CHARACTERISTICS (CONTINUED)
Electrical Characteristics: Unless otherwise specified, maximum values are at TA = –40°C to +85°C,
VDD = 2.7V to 5.5V, VDD I/O= 1.62V to 5.5V, VBUS = 0V to 32V; typical values are at TA = +25°C
VDD = VDD I/O = 3.3V, VBUS = 32V, VSENSE = (SENSE+ – SENSE–) = 0V
Characteristic Symbol Min. Typ. Max. Unit Conditions
2017 Microchip Technology Inc. DS20005850B-page 7
PAC1934
FIGURE 1-1: SMBus Timing.
TABLE 1-2: SMBUS MODULE SPECIFICATIONS
Electrical Characteristics: Unless otherwise specified, maximum values are at TA = –40°C to +85°C,
VDD = 2.7V to 5.5V, VBUS = 0V to 32V; Typical values are at TA = +25°C, VDD = 3.3V, VBUS = 32V,
VSENSE = (SENSE+ – SENSE–) = 0V, VDD I/O = 1.62V to 5.5V
Characteristic Sym. Min. Typ. Max. Units Conditions
SMBus Interface
Input Capacitance CIN — 4 10 pF Not tested in production
SMBus Timing
Clock Frequency fSMB .010 — 1 MHz No minimum if Time-Out is not
enabled.
Spike Suppression tSP 0—50ns
Bus Free Time Stop to
Start
tBUF 0.5 — — µs Per SMBus 3.0
Hold Time after
Repeated Start
Condition
tHD:STA 0.26 — — µs Per SMBus 3.0
Repeated Start
Condition Setup Time
tSU:STA 0.26 — — µs Per SMBus 3.0
Setup Time: Stop tSU:STO 0.26 — — µs Per SMBus 3.0
Setup Time: Start tSU:STA 0.26 — — µs
Data Hold Time tHD:DAT 0——µs
Data Setup Time tSU:DAT 50 — — ns Per SMBus 3.0 (Note 1)
Clock Low Period tLOW 0.5 — — µs Per SMBus 3.0
Clock High Period tHIGH 0.26 — 50 µs
Clock/Data Fall Time tFALL — — 120 ns Not tested in production
Clock/Data Rise Time tRISE — — 120 ns Not tested in production
Capacitive Load CLOAD — — 550 pF Per bus line,
CLOAD not tested in production
SLOW Pin Pulse Width SLOWpw — 100 — µs Pulses narrower than 100 µS
may not be detected
Note 1: A device must internally provide a hold time of at least 300 ns for the SM_DATA signal (with respect to the
VIH(min) of the SM_CLK signal) to bridge the undefined region of the falling edge of SM_CLK.
SMDATA
SMCLK
TLOW
TRISE
THIGH
TFALL
TBUF
THD:STA
PSS - Start Condition P - Stop Condition
THD:DAT TSU:DA
T
TSU:STA
THD:STA
P
TSU:STO
S
PAC1934
DS20005850B-page 8 2017 Microchip Technology Inc.
NOTES:
2017 Microchip Technology Inc. DS20005850B-page 9
PAC1934
2.0 TYPIC AL OPERATING CURVES
Note: Unless otherwise indicated, maximum values are at TA = –40°C to +85°C, VDD = 2.7V to 5.5V, VBUS = 0V to 32V;
typical values are at TA = +25°C, VDD = 3.3V, VBUS = 3.3V, VSENSE = (SENSE+ – SENSE–) = 0V, VDD I/O = 1.62 to 5.5V.
FIGURE 2-1: VSENSE Error vs. V SENSE
Input Voltage.
FIGURE 2-2: VSENSE Error vs. V SENSE
Input Voltage Bidirectional Mode.
FIGURE 2-3: VSENSE Error vs. V SENSE
Input Voltage vs. Temperature.
FIGURE 2-4: VSENSE Error vs. VSENSE
Input Voltage and Temperature.
FIGURE 2-5: VSENSE Error vs. VSENSE
Input Voltage Bidirectional Mode (Zoom View).
FIGURE 2-6: VSENSE Error vs. VSENSE
and Common Mode.
Note: The graphs and tables provided following this note are a statistical summary based on a limited number of
samples and are provided for informational purposes only. The performance characteristics listed herein
are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified
operating range (e.g., outside specified power supply range) and therefore outside the warranted range.
10uV 100uV 1mV 10mV 100mV
-10
5
0
5
10
Sense Input Voltage
Error (percen t)
3.3vDC 25
o
C
-80 -60 -40 -20 020 40 60 80
-0.025%
0.0125%
0
0.0125%
0.025%
Sense Input Voltage (mV)
Error (%FullScale)
CM3.3v 3.3vDC 25
o
C
020mV 40mV 60mV 80mV 100mV
-0.1%
-0.15%
-0.05%
0
0.05%
Sense Input Voltage
Error (%Ful lScale)
Ch1 3.3vDC -40
o
C
Ch1 3.3vDC 0
o
C
Ch1 3.3vDC 25
o
C
Ch1 3.3vDC 85
o
C
Ch1 3.3vDC 125
o
C
1uV 10uV 0.1mV 1mV 10mV 100mV
-15
-10
-5
0
5
10
15
20
25
Sense Input Voltage
Error (percen t)
3.3vDC -40
o
C
3.3vDC 0
o
C
3.3vDC 25
o
C
3.3vDC 85
o
C
3.3vDC 125
o
C
-1mV -0.5mV 00.5mV 1mV
-0.025%
0.025%
0.0125%
-0.0125%
0
Sense Input Voltage
Error (%FullScale)
CM3.3v 3.3vDC 25
o
C
020mV 40mV 60mV 80mV 100mV
0.025%
0
-0.025%
0.05%
-0.05%
Sense Input Voltage
Error (%Ful lScale)
CM1v 3.3vDC 25
o
C
CM3v 3.3vDC 25
o
C
CM5v 3.3vDC 25
o
C
CM16v 3.3vDC 25
o
C
CM32v 3.3vDC 25
o
C
PAC1934
DS20005850B-page 10 2017 Microchip Technology Inc.
FIGURE 2-7: VBUS Error vs. VBUS Input
Voltage.
FIGURE 2-8: VBUS Error vs. VBUS Input
Voltage (Zoom View).
FIGURE 2-9: VBUS Error vs. VBUS Input
Voltage.
FIGURE 2-10: VBUS Error vs. VBUS Input
Voltage vs. Temperature.
FIGURE 2-11: VBUS Error vs. VBUS Input
Voltage vs. Temperature (Zoom View).
FIGURE 2-12: VBUS Error vs. VBUS Input
Voltage vs. Temperature (Bipolar Voltage Mode).
1mV 10mV 0.1V 1V 10V
0
5
10
15
20
25
Input V oltage
Error (percen t)
3.3vDC 25
o
C
10mV 100mV 1V 10V
-2%
-1%
0
1%
2%
Input V oltage
Error (percent)
3.3vDC 25
o
C
0 5 10 15 20 25 30
-0.05%
0
0.05%
-0.1%
Input Voltage
Error (%Ful lScale)
3.3vDC 25
o
C
1mV 10mV 0.1V 1V 10V
0
5
10
15
20
25
Input V oltage
Error (percen t)
3.3vDC -40
o
C
3.3vDC 0
o
C
3.3vDC 25
o
C
3.3vDC 85
o
C
3.3vDC 125
o
C
10mV 100mV 1V 10V 32V
-2%
-1%
0
1%
2%
Input V oltage
Error (percent)
3.3vDC -40
o
C
3.3vDC 0
o
C
3.3vDC 25
o
C
3.3vDC 85
o
C
3.3vDC 125
o
C
-0.5v 0v 0.5v 1v
0.1%
0
-0.2%
-0.4%
-0.6%
-0.8%
Input V oltage
Error (%Ful lScale)
3.3vDC -40
o
C
3.3vDC 0
o
C
3.3vDC 25
o
C
3.3vDC 85
o
C
3.3vDC 125
o
C
2017 Microchip Technology Inc. DS20005850B-page 11
PAC1934
FIGURE 2-13: VBUS Error vs. VBUS Input
Voltage vs. Temperature.
FIGURE 2-14: Zero Input Histogram for
VBUS (LSBs, 8X Average Results).
FIGURE 2-15: Zero Input Histogram for
VSENSE (LSBs, 8X Average Results).
FIGURE 2-16: Input Offset for VBUS
Measurements vs. Temperature.
FIGURE 2-17: Input Offset for VSENSE
Measurements vs. Temperature.
FIGURE 2-18: I2C/SMBus Drive Current
vs. VOL.
0v 5v 10v 15v 20v 25v 30v
-0.1%
-0.2%
0.2%
0
0.1%
Input V oltage
Error (%Ful lScale)
3.3vDC -40
o
C
3.3vDC 0
o
C
3.3vDC 25
o
C
3.3vDC 85
o
C
3.3vDC 125
o
C
-40 025 55 85 125
-1
-0.8
-0.6
-0.4
-0.2
0
Temperature (
o
C)
DC Offset (LSB's 15b+sign)
-40 025 55 85 125
-1
-0.8
-0.6
-0.4
-0.2
0
Temperature (
o
C)
DC Offset (LSB's 15b+sign)
00.1 0.2 0.3 0.4 0.5 0.6 0.7
0
10
20
30
40
50
60
70
SMBUS Output Voltage (VOL)
SMBUS Drive Current (IOL) mA
VIO=1.6v VDD=2.6v
VIO=5.5v VDD=5.5v
PAC1934
DS20005850B-page 12 2017 Microchip Technology Inc.
FIGURE 2-19: IDD vs. Temperature and
Supply at 1024 Samples/Second.
FIGURE 2-20: IDD in SLOW Mode vs.
Temperature and VDD.
FIGURE 2-21: IDD for VDD I/O pin vs.
Temperature and VDD.
FIGURE 2-22: IDD vs.Temperature, VDD,
and Sample Rate.
FIGURE 2-23: IDD in SLEEP Mode vs.
Temperature and VDD.
FIGURE 2-24: IDD in Power Down Mode
vs. Temperature and VDD.
-40 025 55 85 125
520
540
560
580
600
620
640
Temperature (
o
C)
1kSps mode Current (uA)
2.6v
2.7v
3.3v
5.0v
5.5v
5.6v
-40 025 55 85 125
10
20
30
40
50
60
Temperature (
o
C)
8Sps mode Current (uA)
2.6v
2.7v
3.3v
5.0v
5.5v
5.6v
-40 025 55 85 125
0
0.05
0.1
0.15
Temperature (
o
C)
VIO Current (uA)
VDD 2.6v/VIO 1.7v
VDD 5.6v/VIO 1.7v
VDD 2.6v/VIO 5.6v
VDD 5.6v/VIO 5.6v
-40 025 55 85 125
0
100
200
300
400
500
600
700
Temperature (
o
C)
Active Current (uA)
2.6v
2.7v
3.3v
5.0v
5.5v
5.6v
1kSps
256 Sp s
16 Sp s
8 Sps
-40 025 55 85 125
0
5
10
15
20
25
30
Temperature (
o
C)
Sleep mode Current (uA)
2.6v
2.7v
3.3v
5.0v
5.5v
5.6v
-40 025 55 85 125
0
2
4
6
8
10
12
Temperature (
o
C)
PowerDown Current (uA)
2.6v
2.7v
3.3v
5.0v
5.5v
5.6v
2017 Microchip Technology Inc. DS20005850B-page 13
PAC1934
FIGURE 2-25: VSENSE Input Current -
Active Mode, 1024 Samples/Second.
FIGURE 2-26: VBUS Input Leakage Current
vs. VDD and Temperature.
FIGURE 2-27: VBUS Input Current - Active
Mode, 1024 Samples/Second.
FIGURE 2-28: VSENSE Input Leakage
Current vs. VDD and Temperature.
-40 025 55 85 125
-0.5
0
0.5
1
1.5
2
Temperature (
o
C)
Average Current 1kSps (uA)
0v CM
1v CM
5v CM
16v CM
32v CM
-40 025 55 85 125
0.03
0.04
0.05
0.06
0.07
0.08
0.09
0.1
Temperature (
o
C)
Leakage Current (uA)
0v
1v
5v
16v
32v
-40 025 55 85 125
0
0.5
1
1.5
2
2.5
Temperature (
o
C)
Average Current 1kSps (uA)
0v
1v
5v
16v
32v
-40 025 55 85 125
0
0.005
0.01
0.015
0.02
0.025
0.03
Temperature (
o
C)
Leakage Current (uA)
0v CM
1v CM
5v CM
16v CM
32v CM
PAC1934
DS20005850B-page 14 2017 Microchip Technology Inc.
3.0 PIN DESCRIPTIONS
The descriptions of the pins are listed in Table 3-1.
3.1 SenseN+/SenseN– (N=1,2,3,4)
These two pins form the differential input for measuring
voltage across a sense resistor in the application. The
positive input (SenseN+) also acts as the input pin for
bus voltage.
3.2 Ground (GND)
System ground.
3.3 SMBus Data (SM_DATA)
This is the bi-directional SMBus data pin. This pin is
open drain, and requires a pull-up resistor to VDD I/O.
3.4 SMBus Clock (SM_CLK)
This is the SMBus clock input pin.
3.5 Positive Power Supply Voltage
(VDD)
Power supply input pin for the device. 2.7-5.5V range,
bypass with 100 nF ceramic capacitor to ground near
the IC.
3.6 Digital Power Reference Voltage
(VDD I/O)
Connect this pin to the power supply voltage for the dig-
ital controller driving the SMBus pins and digital input
pins for the device, 1.62V-5.5V. Bypass with 100 nF
ceramic capacitor to ground near the IC. This pin does
not supply power, instead it acts as the VIH reference.
3.7 Address Selection (ADDR_SEL)
Connect a resistor from this pin to ground to select
SMBus address.
3.8 Enable pin (PWRDN)
Power down input pin for the device, active low.
3.9 SLOW/ALERT
In default mode, if this pin is forced high, sampling rate
is forced to 8 samples/second. When it is forced low,
the sampling rate is 1024 samples/second unless a dif-
ferent sample rate has been programmed.This pin may
be programmed to act as the ALERT pin, in ALERT
mode the pin needs a pull-up resistor to VDD I/O.
TABLE 3-1: PIN DESCRIPTIONS
PAC1934
WLCSP16 Symbol Pin Type Description
A3 SENSE1+ 32V analog in 0-32V range, Connect to supply side of sense resistor
A2 SENSE1–32V analog in 0-32V range, Connect to load side of sense resistor
A1 SENSE2+ 32V analog in 0-32V range, Connect to supply side of sense resistor
B1 SENSE2– 32V analog in 0-32V range, Connect to load side of sense resistor
D1 SENSE3+ 32V analog in 0-32V range, Connect to supply side of sense resistor
C1 SENSE3–32V analog in 0-32V range, Connect to load side of sense resistor
D3 SENSE4+ 32V analog in 0-32V range, Connect to supply side of sense resistor
D2 SENSE4–32V analog in 0-32V range, Connect to load side of sense resistor
B4 GND Ground pin Ground for the IC
D4 SM_DATA SMBus data I/O Open drain requires pull-up resistor to VDD I/O
C4 SM_CLK SMBus clock Input Clock Input pin
A4 VDD Power for IC Positive power supply voltage
B2 VDD I/O Sets VIH
reference for digital
I/O
Digital power reference level for digital I/O
C2 ADDRSEL Analog I/O pin Address selection for the SMBus Slave address
B3 PWRDN Digital input pin Voltage range is set by VDD I/O pin. Active low puts the device in
power-down state (all circuitry is powered down including SMBus).
C3 SLOW/ALERT Digital I/O pin Voltage range is set by VDD I/O pin. Default function is SLOW, may be
programmed to function as ALERT pin (Open Collector when functioning
as ALERT, requires pull-up resistor to VDD I/O).
2017 Microchip Technology Inc. DS20005850B-page 15
PAC1934
4.0 GENERAL DESCRIPTION
The PAC1934 is a four-channel, bidirectional, high-side
current-sensing device with precision voltage
measurement capabilities, DSP for power calculation
and a power accumulator. It measures the voltage
developed across an external sense resistor (VSENSE)
to represent the high-side current of a battery or
voltage regulator. The PAC1934 also measures the
SENSE+ pin voltages (VBUS). Both VBUS and VSENSE
are converted to digital results by a 16-bit ADC, and the
digital results are multiplied to give VPOWER. The
VPOWER results are accumulated on-chip, which
enables energy measurement over the accumulation
period.
The PAC1934 has an I2C/SMBus interface for digital
control and reading results. It also has digital supply
reference VDD I/O that is to be connected to the same
supply as the digital master for the I2C/SMBUS,
enabling digital I/O voltages as low as 1.62V.
A system diagram is shown in Figure 4-1.
FIGURE 4-1: PAC1934 System Diagram.
Note: VDD and VDD I/O may be connected together.
PAC1934 System
Master
SM_DATA
SM_CLK
VSOURCE 0V – 32V
Sense
Resistors
V
DD
1.62V to 5.5V
Digital Supply
GND
2.7V to 5.5V
SENSE1+
SENSE1-
SENSE2+
SENSE2-
SENSE3+
SENSE3-
SENSE4+
SENSE4-
VSOURCE 0V – 32V
V
SOURCE 0V – 32V
V
SOURCE 0V – 32V
Load
Load
Load
Load
SLOW
PWRDN
ADDRSEL
V
DD
I/O
PAC1934
DS20005850B-page 16 2017 Microchip Technology Inc.
FIGURE 4-2: PAC1934 Functional Block Diagram.
FIGURE 4-3: PCB Pattern for Sense Resistor.
Figure 4-3 shows the recommended PCB pattern for
sense resistor with wide metal for the high-current path.
The drawing shows metal, solder paste openings and
resistor outline. VSOURCE connects to the +terminal of the
high-current path, and the load connects to the –terminal
of the high-current path. Sense+ and Sense– have a Kel-
vin connection to the current sense resistor to ensure that
no metal with high current is included in the VSENSE mea-
surement path. Sense+ and Sense– are shown as a dif-
ferential pair, route them as a differential pair to the Sense
inputs at the chip.
2017 Microchip Technology Inc. DS20005850B-page 17
PAC1934
4.1 Detailed Description
A high-voltage multiplexer connects the input pins to
the VBUS and VSENSE amplifiers. The amplifier outputs
are sampled simultaneously for each channel, con-
verted by 16 bit ADCs and processed for gain and off-
set error correction. After each conversion, VBUS and
VSENSE are multiplied together to give VPOWER.
An internal oscillator and digital control signals control
the two ADCs and the mux. The mux sequentially con-
nects each channel’s amplifiers to the ADC inputs.
The PAC1934 measures the source-side voltage,
VBUS, and the voltage VSENSE across an external cur-
rent sense resistor, RSENSE.
4.1.1 INITIAL OPERATION AND ACTIVE
STATE
After POR and a start-up sequence, the device is in
the ACTIVE state and begins sampling the inputs
sequentially. Voltage and current are sampled for all
active channels and power is calculated and accumu-
lated. All active channels are sampled at 1024 sam-
ples/second by default. Sample rates of 256, 64 or 8
samples/second may be programmed over I2C or
SMBus. If the SLOW pin is asserted the sample rate is
8 samples per second. For sampling rates lower than
1024 samples/second, the device is in Sleep mode for
a portion of the conversion cycle, which results in
lower power dissipation. If fewer than four channels
are active, power is also reduced.
To read accumulator data and reset the accumulators,
the REFRESH command is used. To read the voltage,
current, power and accumulator data without resetting
the accumulators, the REFRESH_V command is
used. Changes to the control register (01h) are acti-
vated by sending either REFRESH or REFRESH_V.
When a new value is written to the Control Register
(01h), the new values take effect at the end of the next
round-robin sampling cycle following the next
REFRESH or REFRESH_V command.
4.1.2 REFRESH COMMAND
The master sends the REFRESH command after
changing the Control Register and/or before reading
accumulator data from the device. The master controls
the accumulation period in this manner.
The readable registers for the VBUS, VSENSE, Power,
accumulator outputs and accumulator count are
updated by the REFRESH command and the values
will be static until the next REFRESH command.
These readable registers will be stable within 1 mS
from sending the REFRESH command, and may be
read by the master at any time up until the next
REFRESH command is sent. The internal accumulator
values and accumulator count will be reset by the
REFRESH command, but the sampling of the inputs,
data conversion and power integration is not inter-
rupted and will continue as determined by the settings
in the control register.
Changes written to the control and configuration regis-
ters take effect 1 mS after a REFRESH command is
sent. Any new commands written within this 1 mS win-
dow will be ignored and NACKed to indicate that they
are ignored.
The values for VBUS and VSENSE measurement results
and Power calculation results respond to the
REFRESH command in the same fashion as the accu-
mulators and accumulator count. The readable regis-
ters will be stable within 1 mS from sending the
REFRESH command and may be read by the master
at any time. The internal values continue to be
updated according to the sampling plan determined by
the settings in the CONTROL register. The results that
are sent to the readable registers for VBUS, VSENSE
and Power are the values from the most recent com-
plete conversion cycle. See Register 6-1 REFRESH
Command (Address 00h).
4.1.3 REFRESH_G COMMAND
The REFRESH_G is identical in every respect to the
REFRESH command, but it is used with the I2C Gen-
eral Call address (0000 000). This allows the system
to issue a REFRESH command to all of the PAC1934
devices in the system with a single command. Then
the data from this REFRESH_G command may be
read device by device to capture a snapshot of the
system power and energy for all devices. See
Register 6-12 REFRESH_G COMMAND (Address
1Eh). Note that the REFRESH_G command can also
be used with a valid Slave Address but in this case
only the device with this Slave Address will receive the
command. In other words it has the same properties
as the REFRESH command with the possibility of
being compatible with the I2C General Call address.
4.1.4 REFRESH_V COMMAND
If the user wants to read VSENSE and VBUS results, the
most recent Power calculation, and/or the accumulator
values and count without resetting the accumulators,
the REFRESH_V command may be sent. Sending the
REFRESH_V command and waiting 1 mS ensures
that the VSENSE, VBUS, Power, accumulator and accu-
mulator count values will be stable when read by the
master. The sampling of the inputs, data conversion
and power integration are not interrupted and will con-
tinue as determined by the settings in the CONTROL
register. The data in these readable registers will
remain stable until the next REFRESH or
REFRESH_V command.The internal accumulator val-
ues and accumulator count are unaffected by the
REFRESH_V command.
Note that the REFRESH_V command may also be
used to activate changes to the CONTROL register,
just like the REFRESH command, except with the
PAC1934
DS20005850B-page 18 2017 Microchip Technology Inc.
REFRESH_V command changes to the control regis-
ter will be enacted without resetting the accumulators
or accumulator count. See Register 6-13
REFRESH_V COMMAND (Address 1Fh).
4.1.5 SLEEP STATE
The SLEEP state is a lower power state than the
ACTIVE state. While in this state, the device will draw
a supply current of ISLEEP from the VDD pin. The
device automatically goes to this state between con-
version cycles when sampling rates lower than 1,024
samples/second are selected, or if fewer than four
channels are active. All digital states and data are
retained in the SLEEP state. The device can also be
put in the SLEEP state by setting the SLEEP bit fol-
lowed by a REFRESH or REFRESH_V command, and
sampling will resume when the SLEEP bit is cleared
followed by a REFRESH of REFRESH_V command.
The device does not go into SLEEP state based on
any other condition such as static conditions on the
SMBus pins. If SMBus Timeout is enabled, it is sup-
ported in SLEEP mode or ACTIVE mode.
4.1.6 POWER-DOWN STATE
The Power-Down state is entered by pulling the
PWRDN pin low. In this state, all circuits on the chip
including the SMBus pins are inactive, and the device
is in a state of minimum power dissipation.
In the Power-Down state, no data is retained in the
chip (neither register configuration nor measurement
data). When the PWRDN pin is pulled high, integra-
tion, measurement and accumulation will begin using
the default register settings, as described in paragraph
3.1.1 above. The first measurement data may be
requested by a REFRESH or REFRESH_V command
20 ms after the PWRDN pin is pulled high.
4.1.7 PROGRAMMING THE SAMPLE
RATE AND THE SLOW PIN
The default sampling rate after power-up is 1024 sam-
ples/second. Sampling rates of 256, 64 or 8 sam-
ples/second may be programmed in the CTRL
REGISTER (Address 01h) (Register 6-2). Any time a
new sample rate is programmed, it does not take effect
until a REFRESH, RERESH_G, or REFRESH_V com-
mand is received. When any of these REFRESH com-
mands are received, any round-robin sampling cycle in
progress will complete before the new sampling rate
takes effect.
If one of these lower sample rates is used, power dissi-
pation is reduced. The round-robin sampling and con-
version cycle is exactly the same, but the device goes
into the sleep state between conversion cycles. See
Section 2.0 “Typical Operating Curves”.
If the SLOW pin is pulled high, the device will sample
at eight samples/second. No matter what the pro-
grammed sample rate, this new SLOW sample rate
will take effect on the next conversion cycle (if a
round-robin conversion cycle is in process when the
SLOW pin goes high, that conversion cycle will com-
plete before the SLOW sample rate takes effect.)
If the device is programmed for Single Shot mode, and
the SLOW pin is asserted, the first sampling will begin
within 125 ms after the SLOW pin is asserted.
If the device is in the SLEEP state, asserting the
SLOW pin will not cause sampling to start.
Whenever the SLOW pin changes state, a limited
REFRESH or REFRESH_V command may be exe-
cuted by the chip hardware (default is REFRESH).
Like any other REFRESH command, this resets the
accumulators and accumulator count for a REFRESH
command, and updates the readable registers for
either REFRESH or REFRESH_V. These are limited
REFRESH commands because no programmed
changes to the control or status registers take effect
(control and status registers means registers 01h,
1Ch, 1Dh, and 20h-26h). The readable registers are
stable with the new values within 1 ms of the SLOW
pin transition.
The SLOW register enables selection of REFRESH or
REFRESH_V on the SLOW pin transitions, which
allows this function to be disabled for either edge, and
also tracks both the state of the SLOW pin and transi-
tions on the SLOW pin. See Register 6-14, SLOW
(Address 20h).
This is the default functionality of the SLOW pin, but it
may be reconfigured to function as an ALERT pin (see
paragraph Section 4.4 “ALERT Functionality”). If
the SLOW pin is configured to serve as an ALERT pin,
the slower sampling rate of eight samples/second is
only available by programming the CONTROL register
01h.
4.2 Conversion Cycles
A conversion cycle for the device consists of analog to
digital conversion being complete for all channels
(including the real-time calibration that is part of each
conversion cycle). Immediately following the data con-
version, the power results are calculated for that chan-
nel and the power value is added to the accumulator.
Averaged values for VSENSE and VBUS are also
updated internally as part of each conversion cycle.
Data conversion and processing is performed for each
active channel in sequential fashion until all active
channels have been converted, completing the con-
version cycle for the device. The sequential sampling
of each channel, along with the calculation time and
any sleep time needed to set the overall sampling rate,
is referred to as a round-robin sampling period.
2017 Microchip Technology Inc. DS20005850B-page 19
PAC1934
4.3 Conversion Cycle Controls
4.3.1 REDUCING THE NUMBER OF
CHANNELS TO BE SAMPLED
Program Register 6-10 CHANNEL_DIS and SMBus
(Address 1Ch) to reduce the number of channels that
are active. The sample rate is unaffected, but power
dissipation is reduced if some channels are disabled.
Any or all channels may be disabled; if all channels
are disabled, the device goes into sleep mode.
4.3.2 SINGLE SHOT MODE
The Control register also allows the device to operate
in Single Shot mode. In Single Shot mode, all active
channels will sample and convert once, followed by
results being calculated. The accumulator and accu-
mulator count operate the same as for continuous con-
version mode, accumulating each single shot power
calculation and incrementing the accumulator count.
The conversion cycle will start when the REFRESH
command (or REFRESH_V or REFRESH_G) is sent.
After the single shot measurements and calculations
are complete, the device will go into SLEEP mode. A
REFRESH, REFRESH_G or REFRESH_V command
may be sent to read the data. The user needs to wait
3 ms after the REFRESH command before command-
ing another Single Shot conversion by means of send-
ing one of the REFRESH commands. This is because
a 1 ms delay is required between Refresh commands,
and coming out of Sleep requires 2 ms.
4.4 ALERT Functionality
The ALERT functionality can serve two purposes: to
notify the system that a conversion cycle for all active
channels is complete, or to notify the system that the
accumulator or accumulator count has overflowed.
4.4.1 USING THE ALERT FUNCTION
To use the ALERT function, configure the SLOW pin to
function as ALERT using the Register 6-2. For this
configuration, the ALERT pin must have a pull-up to
VDD I/O (it will function as an open drain output). If a
pull-up resistor is attached to the pin for ALERT func-
tionality, the device will power up in SLOW mode. Any
of the four sample rates can be programmed using the
CTRL Register 01h.
The ALERT function for Accumulator Overflow can
also be used without reconfiguring the SLOW pin, by
monitoring the OVF bit in the CTRL REGISTER
(Address 01h) Register 6-2.
4.4.2 ALERT AFTER COMPLETE
CONVERSION
The Register 6-2 has a bit ALERT_CC that can be
used to enable the ALERT_CC function. If this bit is
set, the ALERT pin will go low for 5 μS after each com-
plete conversion cycle is complete.
4.4.3 ALERT ON ACCUMULATOR
OVERFLOW
If the ALERT function is enabled, and any of the accu-
mulators or the accumulator count overflows, the
ALERT pin may be used to notify the system. To
enable this trigger for the ALERT pin, bit 1 in the CTRL
REGISTER (Address 01h) Register 6-2 must be set.
Note that the OVF bit in the CTRL REGISTER
(Address 01h) Register 6-2, will be set when these
overflows occur.
4.4.4 CLEARING ALERT AND OVF
When the ALERT function has been tripped by accu-
mulator or accumulator count overflow, it will remain
asserted until a REFRESH command is received.
REFRESH_G will also clear the OVF bit and the
ALERT function, but REFRESH_V will not.
PAC1934
DS20005850B-page 20 2017 Microchip Technology Inc.
4.5 Voltage Measure ment
The VBUS voltage for each channel is measured by the
SENSE+ pin for each channel. A high-voltage multi-
plexer is connected to each SENSE+ pin, and the mul-
tiplexer sequentially connects each SENSE+ input to
and ADC for conversion. The result is stored in a 16-bit
VBUS results register and the 14 MSBs are multiplied by
the VSENSE number for the VPOWER results value. The
VPOWER results are accumulated in the accumulator.
Full-Scale Voltage (FSV) is 32V by default. The device
may be programmed for bipolar VBUS measurements.
in this bipolar mode, the mathematical range for nega-
tive VBUS numbers is –32V, the actual range is limited
to about –200mV due to physical factors. This bipolar
capability for VBUS enables accurate offset measure-
ment and correction. For bipolar operation, the 16-bit
VBUS result is a twos complement (signed) number.
The measured voltage at SENSE+ can be calculated
using Equation 4-1.
EQUATION 4-1: BUS VOLTAGE
4.6 Current Measurement
The PAC1934 includes high-side current sensing cir-
cuits. These circuits measure the voltage (VSENSE)
induced across a fixed external current sense resistor
(RSENSE) and store the voltage as a 16-bit number in
the VSENSE Results registers.
The PAC1934 current sensing operates with a
Full-Scale Range (FSR) of 100 mV in unidirectional
mode (default).
When sensing unidirectional currents (the default
mode), the ADC results are presented in straight binary
format. For bidirectional current sensing, the ADC
results are in two’s complement (signed) format. For
bipolar current measurements, the range is ±100 mV,
but use FSR = 100 mV in the equations that follow. For
best accuracy on current values near zero, it is recom-
mended to use the bidirectional current mode and 8x
average current results.
4.7 Selecting RSENSE Values
RSENSE can easily be calculated if you know the maxi-
mum current you want to sense, as shown in
Equation 4-2.
Consider that you may need to select a value for IMax
that includes current peaks well beyond your nominal
current.
EQUATION 4-2: CALCULATING RSENSE
Full-Scale Current (FSC) can be calculated from
Equation 4-3.
EQUATION 4-3: FULL-SCALE CURRENT
The actual current through RSENSE can then be calcu-
lated using Equation 4-4.
EQUATION 4-4: SENSE CURRENT
VSource 32V VBUS
Denominator
-----------------------------------
=
Where:
VSOURCE = The measured voltage on the
SENSE+ pin
VBUS = The value read from the VBUS
Results Registers
Denominator = 216 for unipolar measurements
=2
15 for bipolar measurements
Rsense FSR
Imax
-------------=
Where:
FSR = Full Scale VSENSE voltage input
RSENSE = External RSENSE resistor value
IMax = Maximum current to measure
FSC 100 m V
RSENSE
----------------------=
Where:
FSC = Full-scale current
RSENSE = External sense resistor value
ISENSE FSC VSENSE
Denominator
-----------------------------------
=
Where:
ISENSE = Actual bus current
FSC = Full-scale current value (from
Equation 4-3)
VSENSE = The value read from the
VSENSE Results Registers
Denominator = 216 for unipolar measurements
=2
15 for bipolar measurements
2017 Microchip Technology Inc. DS20005850B-page 21
PAC1934
4.8 ADC Measurements, Offset, and
8x Averaging
The PAC1934 is primarily desired for energy measure-
ments where many power readings are accumulated.
This is inherently an averaging process. Individual volt-
age and current measurements can also benefit from
averaging to reduce noise and offset. Averaged values
are internally calculated for VBUS and VSENSE, with a
rolling average of the most recent eight values present
in the VBUSn_AVG (Register 6-7) and
VSENSEn_AVG (Register 6-6) registers. The average
is updated internally after every conversion cycle. The
readable registers are updated with REFRESH,
REFRESH_V, or REFRESH_G commands like all the
other readable results registers. These averaged
results should be used for the most accurate, lowest
noise and lowest offset measurements.
The ADC channels use a special offset canceling tech-
nique. If the user observes the unaveraged results for
near-zero values of VBUS and VSENSE, they may
observe a cyclical pattern of offset variation. The user
may think this is noise, but in fact it is due to internal cir-
cuitry switching through different permutations of offset
cancellation circuitry. This small variation in unaver-
aged offset is canceled in the 8x averaged result. It is
also canceled in the Power Accumulator results. The
overall effect is offset that is consistently very close to
zero LSB over supply and temperature variations.
The offset canceling technique is illustrated in
Figure 4-4. It is very difficult to accurately observe, as it
is a challenge to read the data from every conversion
cycle. The effect of capturing data points at a rate that
does not correspond exactly to the internal sampling
rate of the PAC1934 can make these permutations
appear less periodic and deterministic than they are
inside the chip. The data conversion uses one of the
permute positions 1-4 for each input on each conver-
sion, cycling through all four permutations in four con-
versions. When averaged the Permute Enabled result
shown below is realized, evenly distributed around
zero.
FIGURE 4-4: Illustration of the Four
Permute Combinations that the ADC Cycles
through and the Resulting Low Average Offset.
Each Bin Represents One Code.
Results from both the VBUS and VSENSE ADCs are 17b
two's complement (signed) internally. There is an addi-
tional bit of resolution that is not accessible from the
results register. The NEG_PWR (Address 1Dh) register
determines whether the conversion results are
reported in the readable registers as unipolar or bipolar
numbers. Using bipolar numbers can give more accu-
rate results for very small numbers that may actually be
negative for some readings, in addition to measuring
bidirectional currents (charging/discharging) and volt-
ages that can dip below ground.
Averaged values are also calculated for VBUS and
VSENSE. A rolling average of the most recent eight val-
ues is present in the VBUSn_AVG (Register 6-7) and
VSENSEn_AVG (Register 6-6) registers. These regis-
ters require eight conversion cycles after POR before
they represent an accurate value, they are updated
after every conversion cycle. The readable registers
are updated with REFRESH, REFRESH_V or
REFRESH_G commands like all the other readable
results registers.
PAC1934
DS20005850B-page 22 2017 Microchip Technology Inc.
4.9 Power and Energy
The Full-Scale Range for Power depends on the exter-
nal sense resistor used, as shown in Equation 4-5.
EQUATION 4-5: POWER FSR
CALCULATION
The device implements Power measurements by mul-
tiplying VBUS and the VSENSE to give a result VPOWER.
VPOWER values are used to calculate Proportional
Power as shown in Equation 4-6. The Proportional
Power is the fractional portion of Power FSR mea-
sured in one sample. Bipolar mode is where VBUS is
bipolar mode, VBUS is bidirectional mode, or both
VBUS and VSENSE are bipolar/bidirectional.
EQUATION 4-6: PROPORTIONAL POWER
CALCULATION
To calculate the actual power from the Proportional
Power, multiply by the Power FSR as shown in
Equation 4-7. This Actual Power number is the power
measured in one sample.
EQUATION 4-7: POWER CALCULATION
These VPOWER results are digitally accumulated on
chip, and stored in the VACCUM registers.
The energy calculation equations 4-8 and 4-9 use a
different denominator term depending on unipolar or
bipolar mode. Bipolar mode for energy applies when
bipolar/bidirectional mode is used for VBUS and/or
VSENSE. Equation 4-8 shows how to realize this using
the Accumulator results, Accumulator count and the
accumulation period, T. In this equation, T must be
known from a system clock time stamp or other accu-
rate indicator of the total accumulation period.
EQUATION 4-8: ENERGY CALCULATION
EQUATION 4-9: ENERGY CALCULATION
Equation 4-9 shows how to calculate energy using the
accumulated power and the sampling rate, fs.
P o w e r FS R 100 m V R SENSE
32V
=
Where:
RSENSE= External RSENSE resistor value
100 mV = Full-Scale VSENSE voltage input
32V = Full-Scale VBUS voltage input
3.2V2RSENSE
=
PPROP Vpower
Denominator
-----------------------------------=
Where:
Denominator =
=
228 (unipolar mode)
227 (bipolar mode)
Pactual PowerFSR PPROP
=
Energy Vaccum
Denominator
----------------------------------- PwrFSR
T
AccCount
--------------------------
=
Where:
Denominator = 228 (unipolar mode)
=2
27 (bipolar mode)
Energy Vaccum
Denominator
----------------------------------- PwrFSR
fs
--------------------------
=
Where:
Denominator = 228 (unipolar mode)
=2
27 (bipolar mode)
2017 Microchip Technology Inc. DS20005850B-page 23
PAC1934
4.9.1 ADDITIONAL ACCUMULATOR
INFORMATION
The math for the Power calculation and accumulation
inside the chip is always done in two's complement
math, no matter what the user sets the output registers
to show. VBUS and VSENSE are 17-bit two's comple-
ment (signed) numbers internally. VPOWER is the prod-
uct of VSENSE multiplied by the 14 MSBs of VBUS, and
this is a 31 bit two's complement result (signed) inter-
nally. In some cases this results in a Power result that
is not identical to the product of the VBUS results regis-
ter multiplied by the VSENSE register. However, the
Power result from the Power results register is more
accurate than the product of the VBUS register multi-
plied by the VSENSE register in these cases, as
explained below.
If VSENSE and VBUS are both programmed to be
unsigned (unipolar) in register NEG_PWR (Address
1Dh), 16b without sign are exported to VBUS and
VSENSE results registers.
If VBUS is programmed to be signed (bipolar) in
Register 6-11 NEG_PWR (Address 1Dh), the corre-
sponding data is truncated to 16-bit two's complement
(signed) for the readable results register.
If VSENSE is programmed to be signed (bipolar) in reg-
ister NEG_PWR (Address 1Dh), the corresponding
results register value is truncated to 16-bit two's com-
plement (signed), but the power calculation uses 17-bit
two's complement (signed). Therefore, a mismatch is
possible between an externally calculated power value
(VBUS times VSENSE) and the actual power value calcu-
lated internally to the chip. The internally calculated
(and accumulated) value is more accurate than the
externally calculated value in every case.
The continuous power integration periods (also called the
energy accumulation period) can range from ~1ms to
many hours, depending on the number of samples per
second selected via SMBus. The number of samples is
limited by the size of the Accumulator Count Register to
16,777,216 (224). This count corresponds to about 273
minutes at 1024 samples/second, or 582 hours at eight
samples/second. This Accumulator Count can overflow,
and it will not reset when it overflows.
When the accumulation registers reach their maximum
value, this is called accumulator overflow. The accumu-
lator outputs remain at their maximum value; they do
not roll over. The user can calculate the worst-case
time to roll over and read them at or before that time or
use the built in ALERT functions to detect rollover and
read them at that time.
Worst-case accumulator overflow time can be calcu-
lated assuming that every measurement that is accu-
mulated is a full-scale number. Since the power
numbers are 28 bits, and the accumulator is 48 bits, 220
samples can be accumulated before overflow if they
are all full-scale values. For most applications, they will
not all be full-scale numbers; this is especially true if
VBUS is not 32V. If VBUS is a lower number, the maxi-
mum number of full-scale samples that can be accumu-
lated is scaled by 32V/VBUS. This limitation can limit the
accumulation period before overflow to 17 minutes at
1024 samples/second, or 36 hours at eight sam-
ples/second, if most values are near full-scale. The
Accumulator Count limit described above will still limit
the total number of samples to 224.
PAC1934
DS20005850B-page 24 2017 Microchip Technology Inc.
5.0 SMBUS AND I2C
COMMUNICATIONS
PROTOCOL
The PAC1934 device communicates over a two-wire
bus with a controller using SMBus or I2C serial commu-
nication protocol. A detailed timing diagram is shown in
Figure 1-1.
Stretching of the SMCLK signal is supported; however,
the PAC1934 will not stretch the clock signal.
5.1 I2C/SMBus Addressing and
Control Bits
5.1.1 SMBUS ADDRESS AND RD / WR
BIT
The SMBus Address Byte consists of the 7-bit slave
address followed by a 1-bit RD / WR indicator. If this
RD / WR bit is a logic ‘0’, the SMBus master is writing
data to the slave device. If this RD / WR bit is a logic
‘1’, the SMBus master is reading data from the slave
device.
The PAC1934 I2C/SMBus address is determined by a
single pull-down resistor connected between ground
and the ADDRSEL pin as shown in Ta b l e 5 - 1 . The chip
translates the resistor value into an address on
power-up, and the value is latched until another
power-up event takes place. The address cannot be
changed on the fly.
5.1.2 SMBUS START BIT
The SMBus Start bit is defined as a transition of the
SMBus data line from a logic ‘1’ state to a logic ‘0’ state
while the SMBus Clock line is in a logic ‘1’ state.
5.1.3 SMBUS ACK AND NACK BITS
The SMBus slave will ACK (acknowledge) all data
bytes that it receives. This is done by the slave device
pulling the SMBus data line low after the eighth bit of
each byte that is transmitted.
5.1.4 SMBUS STOP BIT
The SMBus Stop bit is defined as a transition of the
SMBus data line from a logic ‘0’ state to a logic ‘1’ state
while the SMBus clock line is in a logic ‘1’ state. When
the PAC1934 detects an SMBus Stop bit, and it has
been communicating with the SMBus protocol, it will
reset its slave interface and prepare to receive further
communications.
5.1.5 SMBUS DATA BYTES
All SMBus data bytes are sent most significant bit first
and composed of 8 bits of information.
TABLE 5-1: ADDRESS SELECT
RESISTOR
RESISTOR (1%) SMBUS ADDRESS
0 (Tie to GND) 0010_000(r/w)
499 0010_001(r/w)
806 0010_010(r/w)
1,270 0010_011(r/w)
2,050 0010_100(r/w)
3,240 0010_101(r/w)
5,230 0010_110(r/w)
8,450 0010_111(r/w)
13,300 0011_000(r/w)
21,500 0011_001(r/w)
34,000 0011_010(r/w)
54,900 0011_011(r/w)
88,700 0011_100(r/w)
140,000 0011_101(r/w)
226,000 0011_110(r/w)
Tie to VDD 0011_111(r/w)
2017 Microchip Technology Inc. DS20005850B-page 25
PAC1934
5.2 SMBus Time-Out
The PAC1934 can support the SMBus Time-Out func-
tionality. This functionality is disabled by default, and
can be enabled by writing to the TIMEOUT bit (see
Register 6-10: CHANNEL_DIS and SMBus (Address
1Ch).
If Time-Out is enabled and the clock is held at logic ‘0’
for tTIMEOUT = 25-43 ms, the device will time-out and
reset the SMBus interface. Communication is restored
with a start condition.
5.3 SMBus and I2C Compatibility
The PAC1934 is compatible with SMBus 3.0 1 MHz
class and I2C Fast-mode Plus. The major differences
between SMBus and I2C devices are highlighted here.
For more information, refer to the SMBus 3.0 and I2C
specifications.
1. If Time-Out function is enabled, the minimum
frequency for SMBus communications is
10 kHz. If Time-Out function is disabled (default
condition), then there is no minimum frequency
for SMBus communications.
2. If SMBus Time-Out is enabled in Register 6-10:
CHANNEL_DIS and SMBus (Address 1Ch),the
SMBus slave protocol will reset if the clock is
held at a logic ‘0’ for tTIMEOUT
. I2C does not have
a time-out, this is the default condition.
3. I2C devices do not support the Alert Response
Address functionality (which is optional for
SMBus).The PAC1934 does not support the
Alert Response Address functionality; instead,
the ALERT is a GPIO pin that may be monitored
by the master or Embedded Controller.
4. I2C devices support Block Read and Block Write
differently. I2C protocol allows for unlimited num-
ber of bytes to be sent in either direction. The
SMBus protocol for Block Read and Block Write
requires that an additional data byte indicating
number of bytes to read/write is transmitted.
PAC1934 devices support the I2C protocol for
Block Read by default (no byte count informa-
tion is sent). If the Byte Count bit is set (see
Register 6-10: CHANNEL_DIS and SMBus
(Address 1Ch), it will be sent as the first data
byte in response to the Block Read command,
per SMBus protocol.
5.4 I2C/SMBus Protocols
The PAC1934 supports Write Byte, Read Byte, Block
Read, Send Byte and Receive Byte as valid protocols.
It will not respond to the Alert Response Address pro-
tocol. It will respond to the I2C General Call Address.
All of the protocol charts listed below use the conven-
tion in Table 5- 2 .
5.5 Auto-Incrementing Pointer
The PAC1934 has an auto-incrementing address pointer.
The pointer has two loops for auto-incrementing, a READ
loop and a WRITE loop.
The READ loop includes all of the readable registers —
all of the configuration and control registers, the results
registers, and the Product ID, Manufacturer ID and
Revision ID registers.
The WRITE loop includes only the writable control and
configuration registers.
Neither loop includes the REFRESH commands.
The READ loop will skip inactive channels, if some
channels have been disabled. This automatic channel
skipping feature can be disabled by setting the NO
SKIP bit in Register 6-10: CHANNEL_DIS and SMBus
(Address 1Ch).
If the user elects to read disabled channels, they will
return FFh and the register address will by NACKed.
See Figure 5-1 below for a graphic representation.
TABLE 5-2: PROTOCOL FORMAT
Data Sent to Device Data Sent to the Master
# of bits sent # of bits sent
PAC1934
DS20005850B-page 26 2017 Microchip Technology Inc.
FIGURE 5-1: READ and WRITE Auto Incrementing Loops.
Figure 5-1 shows how the auto-incrementing READ loop works with SKIP option on and off, for reading. It also shows
how the WRITE loop works with the REFRESH, REFRESH_V, and REFRESH_G commands.
App Read Loop App Write Loop
Don’t care if Channels
ON or OFF
REFRESH
CTRL
ACC_COUNT
VPOWER1_ACC
VPOWER2_ACC
VPOWER3_ACC
VPOWER4_ACC
VBUS1
VBUS2
VBUS3
VBUS4
VSENSE1
VSENSE2
VSENSE3
VSENSE4
VBUS1_AVG
VBUS2_AVG
VBUS3_AVG
VBUS4_AVG
VSENSE1_AVG
VSENSE2_AVG
VSENSE3_AVG
VSENSE4_AVG
VPOWER1
VPOWER2
VPOWER3
VPOWER4
CHANNEL_DIS
NEG_PWR
REFRESH_G
REFRESH_V
SLOW
CTRL_ACT
CHANNEL_DIS_ACT
NEG_PWR_ACT
CTRL_LAT
CHANNEL_DIS_LAT
NEG_PWR_LAT
REFRESH
CTRL
ACC_COUNT
VPOWER1_ACC
VPOWER2_ACC
VPOWER3_ACC
VPOWER4_ACC
VBUS1
VBUS2
VBUS3
VBUS4
VSENSE1
VSENSE2
VSENSE3
VSENSE4
VBUS1_AVG
VBUS2_AVG
VBUS3_AVG
VBUS4_AVG
VSENSE1_AVG
VSENSE2_AVG
VSENSE3_AVG
VSENSE4_AVG
VPOWER1
VPOWER2
VPOWER3
VPOWER4
CHANNEL_DIS
NEG_PWR
REFRESH_G
REFRESH_V
SLOW
CTRL_ACT
CHANNEL_DIS_ACT
NEG_PWR_ACT
CTRL_LAT
CHANNEL_DIS_LAT
NEG_PWR_LAT
PID
MID
REV
PID
MID
REV
Channels ON or
(Cha nn els OFF a nd
Skip OFF)
REFRESH
CTRL
ACC_COUNT
VPOWER1_ACC
VPOWER2_ACC
VPOWER3_ACC
VPOWER4_ACC
VBUS1
VBUS2
VBUS3
VBUS4
VSENSE1
VSENSE2
VSENSE3
VSENSE4
VBUS1_AVG
VBUS2_AVG
VBUS3_AVG
VBUS4_AVG
VSENSE1_AVG
VSENSE2_AVG
VSENSE3_AVG
VSENSE4_AVG
VPOWER1
VPOWER2
VPOWER3
VPOWER4
CHANNEL_DIS
NEG_PWR
REFRESH_G
REFRESH_V
SLOW
CTRL_ACT
CHANNEL_DIS_ACT
NEG_PWR_ACT
CTRL_LAT
CHANNEL_DIS_LAT
NEG_PWR_LAT
PID
MID
REV
Channels 1 & 4 OFF
an d Skip O N
Channels OFF and
Skip ON
REFRESH
CTRL
ACC_COUNT
VPOWER1_ACC
VPOWER2_ACC
VPOWER3_ACC
VPOWER4_ACC
VBUS1
VBUS2
VBUS3
VBUS4
VSENSE1
VSENSE2
VSENSE3
VSENSE4
VBUS1_AVG
VBUS2_AVG
VBUS3_AVG
VBUS4_AVG
VSENSE1_AVG
VSENSE2_AVG
VSENSE3_AVG
VSENSE4_AVG
VPOWER1
VPOWER2
VPOWER3
VPOWER4
CHANNEL_DIS
NEG_PWR
REFRESH_G
REFRESH_V
SLOW
CTRL_ACT
CHANNEL_DIS_ACT
NEG_PWR_ACT
CTRL_LAT
CHANNEL_DIS_LAT
NEG_PWR_LAT
PID
MID
REV
0x00
0x01
0x02
0x03
0x04
0x05
0x06
0x07
0x08
0x09
0x0A
0x0B
0x0C
0x0D
0x0E
0x0F
0x10
0x11
0x12
0x13
0x14
0x15
0x16
0x17
0x18
0x19
0x1A
0x1C
0x1D
0x1E
0x1F
0x20
0x21
0x22
0x23
0x24
0x25
0x26
0xF D
0xF E
0xF F
W
R/W
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R/W
R/W
W
W
R/W
R
R
R
R
R
R
R
R
R
1 byte
1 byte
3 bytes
6 bytes
6 bytes
6 bytes
6 bytes
2 bytes
2 bytes
2 bytes
2 bytes
2 bytes
2 bytes
2 bytes
2 bytes
2 bytes
2 bytes
2 bytes
2 bytes
2 bytes
2 bytes
2 bytes
2 bytes
4 bytes
4 bytes
4 bytes
4 bytes
1 byte
1 byte
1 byte
1 byte
1 byte
1 byte
1 byte
1 byte
1 byte
1 byte
1 byte
1 byte
1 byte
1 byte
2017 Microchip Technology Inc. DS20005850B-page 27
PAC1934
5.6 I2C/SMBus Commands
5.6.1 REFRESH AND REFRESH_V
REFRESH and REFRESH_V commands are sent
using the Send byte command, the Slave Address and
the desired command (00h for REFRESH or 1Fh for
REFRESH_V.See Table 5-3.
5.6.2 GENERAL CALL ADDRESS
RESPONSE
When the master sends the General Call address, the
PAC1934 will be able to execute the REFRESH com-
mand by means of a second version of the REFRESH
command called REFRESH_G (see REFRESH_G
COMMAND (Address 1Eh) Register 6-12.).
Just as the REFRESH command is sent using a Send
Byte command with the slave address, and the
REFRESH command (00h), the REFRESH_G com-
mand is sent using Send Byte with the General Call
address (0000 000) and the REFRESH_G command
(1Eh).
Table 5-4 shows the response to the General Call com-
mand for REFRESH_G.
5.6.3 WRITE BYTE
The Write Byte is used to write one byte of data to the
registers, as shown in Table 5-5.
5.6.4 READ BYTE
The Read Byte protocol is used to read one byte of data
from the registers, as shown in Tabl e 5 - 6 .
If an invalid register address is specified, the slave will
ACK its address but NACK the register address.
The master will NACK (not acknowledge) the data
received from the slave by holding the SMBus data line
high after the eighth data bit has been sent.
TABLE 5-3: REFRESH AND REFRESH_V COMMANDS
START Slave Address WR ACK REFRESH or
REFRESH_V
Command ACK STOP
1 0 YYYY_YYY 0 0 00h or 1Fh 0 0 1
TABLE 5-4: GENERAL CALL RESPONSE
START General Call
Address WR ACK REFRESH_G
Command ACK STOP
1 0 0000_000 0 0 1Eh 0 0 1
TABLE 5-5: WRITE BYTE PROTOCOL
START Slave
Address WR ACK Register
Address ACK Register
Data ACK STOP
1 0 YYYY_YYY 0 0 XXh 0 XXh 0 0 1
TABLE 5-6: READ BYTE PROTOCOL
START Slave
Address WR ACK Register
Address ACK START Slave Address RD ACK Register Data NACK STOP
1 0 YYYY_YYY 0 0 XXh 0 1 0 YYYY_YYY 1 0 XXh 1 0 1
PAC1934
DS20005850B-page 28 2017 Microchip Technology Inc.
5.6.5 SEND BYTE
The Send Byte protocol is used to set the internal
address register pointer to the correct address location.
No data is transferred during the Send Byte protocol,
as shown in Table 5-7 .
5.6.6 RECEIVE BYTE
The Receive Byte protocol is used to read data from a
register when the internal register address pointer is
known to be at the right location (e.g., set via Send
Byte). This is shown in Table 5-8.
When an ACK is received after the REGISTER DATA,
then the address pointer automatically increments.
When a NACK is received after the REGISTER DATA,
then the address pointer stays at the same position.
If the master wishes to continue clocking and read the
next register, the master will ACK after the register
data, instead of sending NACK followed by STOP.
If some channels are deactivated, their data registers
will be skipped by the auto-incrementing pointer. Alter-
natively, you may set bit 0 in Register 6-10 CHAN-
NEL_DIS and SMBus (Address 1Ch) and the pointer
will not skip the addresses associated with the inactive
channels. The measurement data for these inactive
channels will read FFh.
5.6.7 BLOCK READ – I2C VERSION
Block Read is used to read multiple data bytes from a
register that contains more than one byte of data, or
from a group of contiguous registers, as shown in
Table 5-9. The PAC1934 supports I2C Block Read by
default, but the SMBus format can also be supported
(see Table 5-10).
If an invalid register address is specified, the slave will
ACK its address but NACK the register address.
The master will NACK (not acknowledge) the data
received from the slave by holding the SMBus data line
high after the 8th data bit has been sent.
TABLE 5-7: SEND BYTE PROTOCOL
START Slave Address WR ACK Register Address ACK STOP
1 0 YYYY_YYY 0 0 XXh 0 0 1
TABLE 5-8: RECEIVE BYTE PROTOCOL
START Slave Address RD ACK Register Data NACK STOP
1 0 YYYY_YYY 1 0 XXh 1 0 1
TABLE 5-9: BLOCK READ PROTOCOL I2C VERSION (DEFAULT)
START Slave Address WR ACK Register
Address ACK START Slave Address RD ACK Register
Data
1 0 YYYY_YYY 0 0 XXh 0 1 0 YYYY_YYY 1 0 XXh
ACK Register Data ACK Register
Data ACK Register
Data ACK Register
Data NACK STOP
0 XXh 0 XXh 0 XXh 0 XXh 1 0 1
2017 Microchip Technology Inc. DS20005850B-page 29
PAC1934
5.6.8 BLOCK READ – SMBUS VERSION
PAC1934 can also support the SMBus version of Block
Read. If the Byte Count bit is set, Block Read will result
in the device sending the Byte Count data before the
first data byte. This protocol is shown in Table 5-10.
Also see Section 4.3 “Conversion Cycle Controls”
above and Register 6-10 CHANNEL_DIS and SMBus
(Address 1Ch).
TABLE 5-10: BLOCK READ PROTOCOL SMBUS VERSION (MUST SET BYTE COUNT BIT)
START Slave Address WR ACK Register
Address ACK START Slave Address RD ACK Byte Count
1 0 YYYY_YYY 0 0 XXh 0 1 0 YYYY_YYY 1 0 XXh = N
ACK Register Data ACK Register
Data ACK Register
Data ACK Register
Data NACK STOP
0 XXh 0 XXh 0 XXh 0 XXh 1 0 1
PAC1934
DS20005850B-page 30 2017 Microchip Technology Inc.
6.0 REGISTERS IN HEXADECIMAL
ORDER
The registers shown in Tab l e 6 - 1 are accessible
through the SMBus. In the individual register tables that
follow, an entry of ‘—’ indicates that the bit is not used
and will always read ‘0’.
Data represented by the data registers are guaranteed
to be synchronized and stable 1 ms after any of the
REFRESH commands are sent. Immediately after the
REFRESH commands are sent, the data bytes will be
changing dynamically until 1 ms has elapsed. When
new data is written to a control register, and the master
reads it back, this new data will be read back even if no
REFRESH command has been sent to cause the new
data to take effect.
Note: The letter N or n is used to represent
1,2,3,4 in the register and bit names
below, in sections that describe registers
that are grouped for all four channels.
TABLE 6-1: REGISTER SET IN HEXADECIMAL ORDER
Register
Number Description Type Bytes POR
Value
Register 6-1
REFRESH Command (Address 00h)
Send Byte for REFRESH command SEND 0 00h
Register 6-2
CTRL REGISTER (Address 01h)
Configuration controls and status R/W 1 00h
Register 6-3
ACC_COUNT Register (Address 02h)
Accumulator count for all channels Block
Read
3 000000h
Register 6-4
VPOWERN Accumulator Registers: VPOW-
ER1_ACC(03h), VPOWER2_ACC (04h),
VPOWER3_ACC (05h), VPOWER4_ACC
(06h)
Accumulator output for channel 1 Block
Read
6Note 1
Accumulator output for channel 2 Block
Read
6Note 1
Accumulator output for channel 3 Block
Read
6Note 1
Accumulator output for channel 4 Block
Read
6Note 1
Register 6-5
VBUSN Result Registers VBUS1 (07h),
VBUS2 (08h), VBUS3 (09h),VBUS4 (0Ah )
VBUS measurement for channel 1 Block
Read
2 0000h
VBUS measurement for channel 2 Block
Read
2 0000h
VBUS measurement for channel 3 Block
Read
2 0000h
VBUS measurement for channel 4 Block
Read
2 0000h
Note 1: The VPOWERN Accumulator Registers, 03h -06h, have a POR value that is all zeros: 6 bytes
000000000000h.
2017 Microchip Technology Inc. DS20005850B-page 31
PAC1934
Register 6-6
VSENSEn Result Registers: VSENSE1
(0Bh), VSENSE2 (0Ch), VSENSE3 (0Dh),
VSENSE4 (0Eh)
VSENSE measurement for channel 1 Block
Read
2 0000h
VSENSE measurement for channel 2 Block
Read
2 0000h
VSENSE measurement for channel 3 Block
Read
2 0000h
VSENSE measurement for channel 4 Block
Read
2 0000h
Register 6-7
VBUSN_AVG Result Registers
VBUS1_AVG (0Fh), VBUS2_AVG (10h),
VBUS3_AVG (11h), VBUS4_AVG (12h)
Rolling average of 8 most recent
VBUS1 measurements
Block
Read
2 0000h
Rolling average of 8 most recent
VBUS2 measurements
Block
Read
2 0000h
Rolling average of 8 most recent
VBUS3 measurements
Block
Read
2 0000h
Rolling average of 8 most recent
VBUS4 measurements
Block
Read
2 0000h
Register 6-8
VSENSEn AVG Result Register
VSENSE1_AVG (13h), VSENSE2_AVG
(14h), VSENSE3_AVG(15h),
VSENSE4_AVG (16h)
Rolling average of 8 most recent
VSENSE1 measurements
Block
Read
2 0000h
Rolling average of 8 most recent
VSENSE2 measurements
Block
Read
2 0000h
Rolling average of 8 most recent
VSENSE3 measurements
Block
Read
2 0000h
Rolling average of 8 most recent
VSENSE4 measurements
Block
Read
2 0000h
Register 6-9
VPOWERN Result Register: VPOWER1
(17h), VPOWER2 (18h), VPOWER3 (19h),
VPOWER4 (1Ah)
VSENSE x VBUS for Channel 1 Block
Read
4 00000000h
VSENSE x VBUS for Channel 2 Block
Read
4 00000000h
VSENSE x VBUS for Channel 3 Block
Read
4 00000000h
VSENSE x VBUS for Channel 4 Block
Read
4 00000000h
Register 6-10
CHANNEL_DIS and SMBus (Address 1Ch)
Disable selected channels,
activate SMBus functionality,
pointer increment
R/W 1 00h
Register 6-11
NEG_PWR (Address 1Dh)
Configuration control for
enabling bidirectional current and
bipolar voltage measurements
R/W 1 00h
Register 6-12
REFRESH_G COMMAND (Address 1Eh)
REFRESH response to
General Call Address
SEND 0 N/A
Register 6-13
REFRESH_V COMMAND (Address 1Fh)
Refreshes VBUS and VSENSE data
only,
no accumulator reset
SEND 0 N/A
Register 6-14
SLOW (Address 20h)
Status and control for
SLOW pin functions
R/W 1 15h
Register 6-15
CTRL_ACT Register (Address 21h)
Currently active value of 01h
(Control)
R 1 00h
TABLE 6-1: REGISTER SET IN HEXADECIMAL ORDER (CONTIN UED)
Register
Number Description Type Bytes POR
Value
Note 1: The VPOWERN Accumulator Registers, 03h -06h, have a POR value that is all zeros: 6 bytes
000000000000h.
PAC1934
DS20005850B-page 32 2017 Microchip Technology Inc.
Register 6-16
Channel DIS_ACT (Address 22h)
Currently active value of
1Ch (CHANNEL_DIS and SMBus)
R 1 00h
Register 6-17
NEG_PWR_ACT (Address 23h)
Currently active value of
1Dh(NEG_PWR)
R 1 00h
Register 6-18
CTRL_LAT Register (Address 24h)
Latched image of 21h (CTRL_ACT) R 1 00h
Register 6-19
Channel DIS_LAT (Address 25h)
Latched image of
22h (Channel DIS_ACT)
R 1 00h
Register 6-20
NEG_PWR _LAT (Address 26h)
Latched image of
23h (NEG_PWR_ACT)
R 1 00h
Register 6-21
Product ID Register (Address FDh)
Stores the Product ID R 1 5Bh
Register 6-22
Manufacturer ID Register (Address FEh)
Stores the Manufacturer ID R 1 5Dh
Register 6-23
Revision ID Register (Address FFh)
Stores the revision R 1 03h
TABLE 6-1: REGISTER SET IN HEXADECIMAL ORDER (CONTIN UED)
Register
Number Description Type Bytes POR
Value
Note 1: The VPOWERN Accumulator Registers, 03h -06h, have a POR value that is all zeros: 6 bytes
000000000000h.
2017 Microchip Technology Inc. DS20005850B-page 33
PAC1934
6.1 Detailed Register Information
REGISTER 6-1: REFRESH COMMAND (ADDRESS 00H)
SEND SEND SEND SEND SEND SEND SEND SEND
No Data in this command, Send Byte only
bit 7 bit 0
Legend:
R = Readable bit W = Writeable bit U = Unimplemented bit, read as ‘0’
-n = Value at POR ‘1’ = bit is set ‘0’ = Bit is cleared x = Bit is unknown
bit 7:0 This command is a SEND Byte, does not contain any data. When it is sent to the device, the REFRESH
command is executed. The accumulator data, accumulator count, VBUS, and VSENSE measurements
are all refreshed and the accumulators are reset. The master can read the accumulator data and accu-
mulator count anytime 1ms after the REFRESH command is sent, and anytime after than up until the
next REFRESH command is sent. (The master can read VBUS and VSENSE data in the same time
period. The accumulator results, accumulator count, VBUS and VSENSE data can be refreshed with the
REFRESH_V command without resetting the accumulators, see Register 5-7).
REGISTER 6-2: CTRL REGISTER (ADDRESS 01H)
RW-0 RW-0 RW-0 RW-0 RW-0 RW-0 RW-0 R-0
Sample_Rate<1:0> SLEEP SING ALERT_PIN ALERT_CC OVF ALERT OVF
bit 7 bit 0
Legend:
R = Readable bit W = Writeable bit U = Unimplemented bit, read as ‘0’
-n = Value at POR ‘1’ = bit is set ‘0’ = Bit is cleared x = Bit is unknown
bit 7:1 Write to these bits to change settings from default value
bit 7:6 Sample_Rate<1:0> - determines sample rate in Normal mode (that is, if SLOW pin is not asserted)
00b = 1024 samples/s
01b = 256 samples/s
10b = 64 samples/s
11b = 8 samples/s
bit 5 SLEEP: setting this bit to 1, followed by the REFRESH or REFRESH_V command, puts the device in
SLEEP mode. All programmed, readable, and measured digital data is stable in this mode. Clear-
ing the SLEEP bit and sending a REFRESH or REFRESH_V command causes the device
become active and start converting in the mode specified by the CONTROL registers (unless the
SLOW pin is asserted, in which case it will start converting at an 8 Hz rate). The SLEEP bit has
higher priority than the SING bit or the SLOW pin, if the SLEEP bit is set the device goes into
SLEEP mode not matter how the SING bit or the SLOW pin are set.
0 = Active mode
1 = SLEEP mode, no data conversion
bit 4 SING: setting this bit to 1 puts the device in Single-shot mode. After writing this bit and sending a
REFRESH command, the device resets the accumulators and performs one conversion cycle for
any and all active channels, then returns to sleep mode. Another REFRESH command, without
changing this bit, will perform another single-shot command. When the bit is cleared, sending a
REFRESH command resets the accumulators and causes the device to start converting in the
sequential scan mode for active channels. A REFRESH_V command may be used instead of
REFRESH to move in and out of Single Shot mode without resetting the accumulators and accu-
mulator count.
0 = Sequential scan mode
1 = Single-shot mode
PAC1934
DS20005850B-page 34 2017 Microchip Technology Inc.
bit 3 ALERT_PIN: Setting this bit to 1 causes the SLOW pin to function as an ALERT pin (active low output
pin). If this bit is set to 1, the ALERT pin can be triggered by conversion complete if bit 2 is set.
If this bit is set to 1, and the Overflow ALERT enable bit is set to 1, the ALERT pin will be triggered by
accumulator or accumulator count overflow. see bit 1 and bit 0 descriptions directly below)
Note that bit 3 only determines the functionality of this pin, SLOW or ALERT, it does not influence the
ALERT functionality. If there is a pull-up resistor connected to the pin for ALERT functionality, the
device will initially power-up in SLOW mode. Once bit 3 is set to enable ALERT functionality, the con-
version rate will change to either the default or programmed value.
0 = Disable the ALERT pin function
1 = Enable the ALERT pin function
bit 2 ALERT_CC: Setting this bit to 1 causes the ALERT pin to be asserted for 5 μS at the end of each con-
version cycle.
0 = No ALERT on Conversion Cycle Complete
1 = ALERT function asserted for 5uS on each completion of the conversion cycle
Note: If this bit and the OVF ALERT bit are set, OVF ALERT dominates. EOC alerts will not be
seen on the ALERT pin if OVF ALERT =1.
bit 1 OVF ALERT: Overflow ALERT enable. If this bit is set and any of the accumulators or the accumulator
counter overflow, the ALERT function will be triggered. This will be reflected in bit 0 of this register, and
if bit 3 is set to a 1, the ALERT pin will be triggered (sent low).
The ALERT function is cleared by REFRESH or REFRESH_G.
0 = no ALERT if accumulator or accumulator counter overflow has occurred.
1 = ALERT pin triggered if accumulator or accumulator counter has overflowed
Note: If this bit and the ALERT_CC bit are set, OVF ALERT dominates. EOC alerts will not be
seen on the ALERT pin if OVF ALERT =1.
bit 0 OVF: Overflow indication status bit, this bit will be set to 1 if any of the accumulators or the accumula-
tor counter overflows.This bit is by cleared REFRESH or REFRESH_G. These commands also clear
the ALERT function.
0 = no accumulator or accumulator counter overflow has occurred.
1 = accumulator or accumulator counter has overflowed
REGISTER 6-2: CTRL REGISTER (ADDRESS 01H) (CONTINUED)
REGISTER 6-3: ACC_COUNT REGISTER (ADDRESS 02h)
R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0
ACC_COUNT<23:16>
bit 23 bit 16
R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0
ACC_COUNT<15:8>
bit 15 bit 8
R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0
ACC_COUNT<7:0>
bit 7 bit0 bit0
Legend:
R = Readable bit W = Writeable bit U = Unimplemented bit, read as ‘0’
-n = Value at POR ‘1’ = bit is set ‘0’ = Bit is cleared x = Bit is unknown
bit 23:0 ACC_COUNT[23:0]: This register contains the count for each time a power result has been summed in
the accumulator
2017 Microchip Technology Inc. DS20005850B-page 35
PAC1934
REGISTER 6-4: VPOWERN ACCUMULATOR REGISTERS: VPOWER1_ACC(03h),
VPOWER2_ACC (04h), VPOWER3_ACC (05h), VPOWER4_ACC (06h)
R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0
VPOWERn<47:40>
bit 47 bit 40
R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0
VPOWERn<39:32>
bit 39 bit 32
R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0
VPOWERn<31:24>
bit 31 bit 24
R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0
VPOWERn<23:16>
bit 23 bit 16
R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0
VPOWERn<15:8>
bit 15 bit 8
R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0
VPOWERn<7:0>
bit 7 bit 0
Legend:
R = Readable bit W = Writeable bit U = Unimplemented bit, read as ‘0’
-n = Value at POR ‘1’ = bit is set ‘0’ = Bit is cleared x = Bit is unknown
bit 47:0 VPOWERn_ACC<47:0>: These registers contain the accumulated sum of VPOWER samples,
where n = 1 to 4, depending on device. These are 48 bit unsigned numbers unless either VBUS or
VSENSE are configured to have a bipolar range. In that case they will be 48-bit two's complement
(signed) numbers.
Note that power is always calculated and accumulated using signed numbers for VBUS and VSENSE,
but if both VBUS and VSENSE are in the default unipolar mode, power is reported as an unsigned num-
ber. This can lead to very small discrepancies between a manual comparison of the product of VBUS
and VSENSE and the results that the chip calculates and accumulates for VPOWER. The digital math in
the chip uses more bits than the reported results for VBUS and VSENSE, so the results registers for
VPOWER and Accumulated Power will in some cases have a more accurate number than calculations
using the results registers for VSENSE and VBUS will provide.
REGISTER 6-5: VBUSN RESULT REGISTERS VBUS1 (07h), VBUS2 (08h), VBUS3 (09h),VBUS4
(0Ah)
R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0
VBUSn<15:8>
bit 15 bit 8
R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0
VBUSn<7:0>
bit 7 bit 0
PAC1934
DS20005850B-page 36 2017 Microchip Technology Inc.
Legend:
R = Readable bit W = Writeable bit U = Unimplemented bit, read as ‘0’
-n = Value at POR ‘1’ = bit is set ‘0’ = Bit is cleared x = Bit is unknown
bit 15:0 VBUSn<15:0>: These registers contain the most recent digitized value of a VBUS sample, where n = 1
to 4, depending on device. These are 16 bit unsigned numbers unless VBUS is configured to have a
bipolar range. In that case they will be 16-bit two's complement (signed) numbers.
REGISTER 6-5: VBUSN RESULT REGISTERS VBUS1 (07h), VBUS2 (08h), VBUS3 (09h),VBUS4
(0Ah) (CONTIN U ED)
REGISTER 6-6: VSENSEn RESULT REGISTERS: VSENSE1 (0Bh), VSENSE2 (0Ch), VSENSE3
(0Dh), VSENSE4 (0Eh)
R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0
VSENSEn<15:8>
bit 15 bit 8
R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0
VSENSEn<7:0>
bit 7 bit 0
Legend:
R = Readable bit W = Writeable bit U = Unimplemented bit, read as ‘0’
-n = Value at POR ‘1’ = bit is set ‘0’ = Bit is cleared x = Bit is unknown
bit 15:0 VSENSEn<15:0>: These registers contain the most recent digitized value of VSENSE samples, where
n = 1 to 4, depending on device.These are 16 bit unsigned numbers unless VSENSE is configured to
have a bipolar range. In that case they will be 16-bit two's complement (signed) numbers.
REGISTER 6-7: VBUSN_AVG RESULT REGISTERS VBUS1_AVG (0FH), VBUS2_AVG (10H),
VBUS3_AVG (11H), VBUS4_AVG (12H)
R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0
VBUSn_AVG<15:8>
bit 15 bit 8
R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0
VBUSn_AVG<7:0>
bit 7 bit 0
Legend:
R = Readable bit W = Writeable bit U = Unimplemented bit, read as ‘0’
-n = Value at POR ‘1’ = bit is set ‘0’ = Bit is cleared x = Bit is unknown
bit 15:0 VBUSn_AVG<15:0>: These registers contain a rolling average of the 8 most recent VBUS measure-
ments. They have the same format as the values in the VBUS registers.
2017 Microchip Technology Inc. DS20005850B-page 37
PAC1934
REGISTER 6-8: VSENSEn A VG RESULT REGISTER VSENSE1_AVG (13H), VSENSE2_A VG (14H),
VSENSE3_AVG(15H), VSENSE4_AVG (16H)
R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0
VSENSEn_AVG<15:8>
bit 15 bit 8
R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0
VSENSEn_AVG<7:0>
bit 7 bit 0
Legend:
R = Readable bit W = Writeable bit U = Unimplemented bit, read as ‘0’
-n = Value at POR ‘1’ = bit is set ‘0’ = Bit is cleared x = Bit is unknown
bit 15:0 VSENSEn_AVG<15:0>: These registers contain a rolling average of the 8 most recent VSENSE results
They have the same format as the values in the VSENSE registers,.
REGISTER 6-9: VPOWERN RESULT REGISTER: VPOWER1 (17H), VPOWER2 (18H), VPOWER3
(19H), VPOWER4 (1AH)
R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0
VPOWERn<27:20>
bit 31 bit 24
R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0
VPOWERn<19:12>
bit 23 bit 16
R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0
VPOWERn<11:4>
bit 15 bit 8
R-0 R-0 R-0 R-0 U U U U
VPOWERn<3:0> ————
bit 7 bit 0
Legend:
R = Readable bit W = Writeable bit U = Unimplemented bit, read as ‘0’
-n = Value at POR ‘1’ = bit is set ‘0’ = Bit is cleared x = Bit is unknown
bit 31:4 VPOWERn<27:0>: These registers contain the product of VBUS (14 MSBs) and VSENSE which rep-
resents Proportional Power for each channel.These are 28 bit unsigned numbers unless either VBUS
or VSENSE are configured to have a bipolar range. In that case they will be 28-bit two's complement
(signed) numbers.These are the numbers that are accumulated in the accumulators.
Note that power is always calculated using signed numbers for VBUS and VSENSE, but if both VBUS and
VSENSE are in the default unipolar mode, power is reported as an unsigned number. This can lead to
very small discrepancies between a manual comparison of the product of VBUS and VSENSE and the
results that the chip calculates for VPOWER.The digital math in the chip uses more bits than the
reported results for VBUS and VSENSE, so the results registers for VPOWER and Accumulated Power
will in some cases have a more accurate number than calculations using the results registers for
VSENSE and VBUS will provide.
bit 3:0 Not used at this time, always reads 0
PAC1934
DS20005850B-page 38 2017 Microchip Technology Inc.
REGISTER 6-10: CHANNEL_DIS AND SMBUS (ADDRESS 1CH)
RW-0 RW-0 RW-0 RW-0 RW-0 RW-0 RW-0 U
CH1_OFF CH2_OFF CH3_OFF CH4_OFF TIMEOUT BYTE
COUNT NO SKIP —
bit 7 bit 0
Legend:
R = Readable bit W = Writeable bit U = Unimplemented bit, read as ‘0’
-n = Value at POR ‘1’ = bit is set ‘0’ = Bit is cleared x = Bit is unknown
bit 7:4 CHn_OFF<7:4> - Allows one or more channels to be inactive during the conversion cycle. These set-
tings apply for normal continuous round-robin conversion cycles or Single-Shot mode, if Single-Shot
mode is selected. Note that if a channel is set to inactive, the auto incrementing address pointer will
skip addresses associated with that channel unless the Pointer Skipping bit 1 in this register is set.
Changes to bits 7:4 do not take effect until a REFRESH, REFRESH_V, or REFRESH_G command are
sent.
Changes to bits 3:1 take place as soon as a new value is written, they are not gated by a REFRESH
command like most other control bits.
bit 7 0 = CH1 ON. Channel 1 active during conversion cycle
1 = CH1 OFF. Channel 1 inactive during conversion cycle
bit 6 0 = CH1 ON. Channel 2 active during conversion cycle
1 = CH1 OFF. Channel 2 inactive during conversion cycle
bit 5 0 = CH1 ON. Channel 3 active during conversion cycle
1 = CH1 OFF. Channel 3 inactive during conversion cycle
bit 4 0 = CH1 ON. Channel 4 active during conversion cycle
1 = CH1 OFF. Channel 4 inactive during conversion cycle
bit 3 Timeout enable bit. The SMBus timeout is disabled by default, and is enabled by setting this bit.
0 = No SMBus timeout feature
1 = SMBus timeout feature is available.
bit 2 This bit causes Byte Count data to be included in the response to the SMBus Block Read command for
each register read. This functionality is disabled by default, and Block Read corresponds to I2C Proto-
col.
0 = No Byte Count in response to a Block Read command
1 = Data in response to a Block Read command includes the Byte Count data
bit 1 NO SKIP - This bit controls the auto-incrementing of the address pointer for channels that are inactive.
0 = The auto-incrementing pointer will skip over addresses used by/for channels that are inactive.
1 = The auto-incrementing pointer will not skip over addresses used by/for channels that are inactive.
With this setting, these channels that are disabled will read 0xFF if read.
bit 0 Unimplemented bits always read 0
2017 Microchip Technology Inc. DS20005850B-page 39
PAC1934
REGISTER 6-11: NEG_PWR (ADDRESS 1DH)
RW-0 RW-0 RW-0 RW-0 RW-0 RW-0 RW-0 RW-0
CH1_BIDI CH2_BIDI CH3_BIDI CH4 BIDI CH1_BIDV CH2_BIDV CH3_BIDV CH4_BIDV
bit 7 bit 0
Legend:
R = Readable bit W = Writeable bit U = Unimplemented bit, read as ‘0’
-n = Value at POR ‘1’ = bit is set ‘0’ = Bit is cleared x = Bit is unknown
bit 7:4 These control bits allow the user to enable bidirectional current measurements for any channel, which
will result in the VSENSE voltage measurement data being in 16-bit two's complement (signed) format.
If the channel is enabled for negative current measurements, the full scale range for VSENSE is –100 mV
to +100 mV.
If these bits are enabled for any channel, that channel’s power numbers are also capable of reporting
bidirectional numbers in two’s complement format.
bit 3:0 These control bits allow the user to enable bidirectional/bipolar voltage measurements for any channel,
which will result in the VBUS voltage measurement data being in 16 bit two’s complement format.
If the channel is enabled for negative voltage measurements, the full scale range for VBUS is +32V to –
32V.Note that this range is the digital FSR, the VBUS input will not give accurate measurements if taken
more than 200 mV below ground.
If these bits are enabled for any channel, that channel’s power numbers are also capable of reporting
bidirectional numbers in two’s complement format.
bit 7 0 = Channel 1 VSENSE ADC converts 0 to +100 mV range with 16-bit straight binary output
1 = Channel 1 VSENSE ADC converts –100 mV to +100 mV range with 16-bit two’s complement output
bit 6 0 = Channel 2 VSENSE ADC converts 0 to +100 mV range with 16 bit straight binary output
1 = Channel 2 VSENSE ADC converts –100 mV to +100 mV range with 16 bit two’s complement output
bit 5 0 = Channel 3 VSENSE ADC converts 0 to +100 mV range with 16-bit straight binary output
1 = Channel 3 VSENSE ADC converts –100 mV to +100 mV range with 16-bit two’s complement output
bit 4 0 = Channel 4 VSENSE ADC converts 0 to +100 mV range with 16-bit straight binary output
1 = Channel 4 VSENSE ADC converts –100 mV to +100 mV range with 16 bit two’s complement output
bit 3 0 = Channel 1 VBUS ADC converts 0 to +32V range with 16-bit straight binary output
1 = Channel 1 VBUS ADC converts –32V to +32 range with 16-bit two’s complement output
bit 2 0 = Channel 2 VBUS ADC converts 0 to +32V range with 16-bit straight binary output
1 = Channel 2 VBUS ADC converts –32V to +32V range with 16-bit two’s complement output
bit 1 0 = Channel 3 VBUS ADC converts 0 to +32V range with 16-bit straight binary output
1 = Channel 3 VBUS ADC converts –32V to +32V range with 16-bit two’s complement output
bit 0 0 = Channel 4 VBUS ADC converts 0 to +32V range with 16-bit straight binary output
1 = Channel 4 VBUS ADC converts –32V to +32V range with 16-d1sw2fxbit two’s complement output
PAC1934
DS20005850B-page 40 2017 Microchip Technology Inc.
REGISTER 6-12: REFRESH_G COMMAND (ADDRESS 1EH)
SEND SEND SEND SEND SEND SEND SEND SEND
No Data in this command, Send Byte only
bit 7 bit 0
Legend:
R = Readable bit W = Writeable bit U = Unimplemented bit, read as ‘0’
-n = Value at POR ‘1’ = bit is set ‘0’ = Bit is cleared x = Bit is unknown
bit 7:0 This command is a SEND Byte, does not contain any data. It is exactly like the REFRESH command
but is intended for use with the General Call command.
When it is sent to the device, the REFRESH command is executed and the readable accumulator data,
readable accumulator count, VBUS, and VSENSE measurements are all refreshed and the internal
accumulators values or accumulator count are reset, exactly like the REFRESH command. The
master can read the updated data 1 ms after the REFRESH_G command is sent, and anytime
after than up until the next REFRESH, REFRESH_G, or REFRESH_V command is sent.
REGISTER 6-13: REFRESH_V COMMAND (ADDRESS 1FH)
SEND SEND SEND SEND SEND SEND SEND SEND
No Data in this command, Send Byte only
bit 7 bit 0
Legend:
R = Readable bit W = Writeable bit U = Unimplemented bit, read as ‘0’
-n = Value at POR ‘1’ = bit is set ‘0’ = Bit is cleared x = Bit is unknown
bit 7:0 This command is a SEND Byte, does not contain any data. When it is sent to the device, the
REFRESH_V command is executed.
It is similar to the REFRESH command except the accumulators and accumulator count are not reset.
The readable accumulator data, readable accumulator count, VBUS, and VSENSE measurements are
all refreshed without affecting the internal accumulators values or accumulator count. The master can
read the updated data 1 ms after the REFRESH_V command is sent, and anytime after than up until
the next REFRESH, REFRESH_G, or REFRESH_V command is sent.
2017 Microchip Technology Inc. DS20005850B-page 41
PAC1934
REGISTER 6-14: SLOW (ADDRESS 20H)
R-0 R-0 R-0 RW-1 RW-0 RW-1 RW-0 RW-1
SLOW SLOW-LH SLOW_HL R_RISE R_V_RISE R_FALL R_V_FALL POR
bit 7 bit 0
Legend:
R = Readable bit W = Writeable bit U = Unimplemented bit, read as ‘0’
-n = Value at POR ‘1’ = bit is set ‘0’ = Bit is cleared x = Bit is unknown
This register tracks the state of the SLOW pin, tracks transitions on the SLOW pin, and controls the type of limited
REFRESH command (if any) that occurs on a SLOW pin transitions. This allows software to monitor the state of the
SLOW pin and its transitions over I2C even though the SLOW pin is asynchronous to the I2C pins and may have a
different controller.
Note that if a REFRESH and REFRESH_V are both enabled for a certain SLOW pin transition, REFRESH will be exe-
cuted (REFRESH wins over REFRESH_V).
On a transition of the SLOW pin, a limited REFRESH function is executed. These limited REFRESH and REFRESH_V
functions update all of the readable results registers. For the limited REFRESH function only, it also reset the accu-
mulators and accumulator count. These are called limited REFRESH and limited REFRESH_V functions because
there is no activation of any pending changes to the control registers.
If the SLOW pin is configured to act as an ALERT pin, all of these bits are always 0. The bits are not cleared when
read, see the details on each bit for clearing information.
SLOW Control and Status Bits
bit 7 =0
bit 7 = 1
The SLOW pin is pulled low externally
The SLOW pin is pulled high externally
bit 6 = 0
bit 6 = 1
The SLOW pin has not transitioned low to high since the last REFRESH command
The SLOW pin has transitioned low to high since the last REFRESH command
The bit is reset to 0 by a REFRESH or REFRESH_G command
bit 5 = 0
bit 5 = 1
The SLOW pin has not transitioned high to low since the last REFRESH command
The SLOW pin has transitioned high to low since the last REFRESH command
The bit is reset to 0 by a REFRESH or REFRESH_G command
bit 4 = 0
bit 4 = 1
Disables a limited REFRESH function to take place on the rising edge of the SLOW pin
Enables a limited REFRESH function to take place on the rising edge of the SLOW pin
The bit is not reset automatically, it must be written to be changed.
bit 3 = 0
bit 3 = 1
Disables a limited REFRESH_V function to take place on the rising edge of the SLOW pin
Enables a limited REFRESH_V function to take place on the rising edge of the SLOW pin
The bit is not reset automatically, it must be written to be changed.
bit 2 =0
bit 2 = 1
Disables a limited REFRESH function to take place on the falling edge of the SLOW pin
Enables a limited REFRESH function to take place on the falling edge of the SLOW pin
The bit is not reset automatically, it must be written to be changed.
bit 1 = 0
bit 1 = 1
Disables a limited REFRESH_V function to take place on the falling edge of the SLOW pin
Enables a limited REFRESH_V function to take place on the falling edge of the SLOW pin
The bit is not reset automatically, it must be written to be changed.
POR Status Bit
The POR bit is a POR flag, for the purpose of enabling the system designer can clear it after POR, and then monitor
it to detect if the device was powered cycled or somehow reset since the POR. If the reset is detected in this manner,
any non-default programming can be reprogrammed.
bit 0 = 0
bit 0 = 1
this bit has been cleared over I2C since the last POR occurred.
this bit has the POR default value of 1, and has not been cleared since the last reset occurred
This bit is only reset by POR
PAC1934
DS20005850B-page 42 2017 Microchip Technology Inc.
REGISTER 6-15: CTRL_ACT REGISTER (ADDRESS 21H)
R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0
Sample_Rate<1:0> SLEEP SING ALERT_PIN ALERT_CC OVF ALERT OVF
bit 7 bit 0
Legend:
R = Readable bit W = Writeable bit U = Unimplemented bit, read as ‘0’
-n = Value at POR ‘1’ = bit is set ‘0’ = Bit is cleared x = Bit is unknown
This register contains an image of the Control register, 01h. The bits in this register reflect the current active value of
these settings, whereas the values in register 01h may have been programmed but not activated by one of the
REFRESH commands. This register allows software to determine the actual active setting.
This register is valid when the Results registers are valid, 1 ms after a REFRESH/_V/_G command (in most cases).
However, if you program a conversion rate change followed by REFRESH, the new conversion rate will not become
effective until the current conversion cycle is complete. This can cause a delay in come cases before the conversion
cycle (and the CTRL_ACT register) are updated. This delay can be variable, depending on where we are in the con-
version cycle when the REFRESH command is sent.
bit 7:6 Sample_Rate<1:0> - shows the value that is currently active since the most recent REFRESH function
was received for programmed sample rate in Normal mode (that is, if SLOW pin is not asserted)
00b = 1024 samples/s
01b = 256 samples/s
10b = 64 samples/s
11b = 8 samples/s
bit 5 SLEEP: This bit shows the value that is currently active since the most recent REFRESH function was
received for the SLEEP bit.
0 = Active mode
1 = SLEEP mode, no data conversion
bit 4 SING: this bit shows the value that is currently active since the most recent REFRESH function was
received for the single shot select bit, SING.
0 = Sequential scan mode
1 = Single-shot mode
bit 3 This bit shows the value that is currently active since the most recent REFRESH function was received
for the ALERT_PIN bit.
0 = Disable the ALERT pin function
1 = Enable the ALERT pin function
bit 2 This bit shows the value that is currently active since the most recent REFRESH function was received
for the ALERT_CC bit.
0 = No ALERT on Conversion Cycle Complete
1 = ALERT function asserted for 5uS on each completion of the conversion cycle
bit 1 This bit shows the value that is currently active since the most recent REFRESH function was received
for the OVF ALERT bit.
0 = No ALERT if accumulator or accumulator counter overflow has occurred.
1 = ALERT pin triggered if accumulator or accumulator counter has overflowed
bit 0 This bit shows the value that is currently active since the most recent REFRESH function was received
for the OVF bit.
0 = No accumulator or accumulator counter overflow has occurred.
1 = Accumulator or accumulator counter has overflowed
2017 Microchip Technology Inc. DS20005850B-page 43
PAC1934
REGISTER 6-16: CHANNEL DIS_ACT (ADDRESS 22H)
R-0 R-0 R-0 R-0 U U U U
CH1_OFF CH2_OFF CH3_OFF CH4_OFF ————
bit 7 bit 0
Legend:
R = Readable bit W = Writeable bit U = Unimplemented bit, read as ‘0’
-n = Value at POR ‘1’ = bit is set ‘0’ = Bit is cleared x = Bit is unknown
This register contains an image of the Channel Disable bits in register 1Ch.The bits in this register reflect the value
that was activated by the most recent REFRESH function, and is currently active. Whereas the values in register 1Ch
may have been programmed but not activated by one of the REFRESH commands, register 22h allows software to
determine the actual active setting. This register is valid when the Results registers are valid, 1 ms after a
REFRESH/_V/_G command.
bit <7:4> CHn_OFF<7:4> – Shows the value that is currently active for these bits
bit 7 0 = CH1 ON. Channel 1 active during conversion cycle
1 = CH1 OFF. Channel 1 inactive during conversion cycle
bit 6 0 = CH1 ON. Channel 2 active during conversion cycle
1 = CH1 OFF. Channel 2 inactive during conversion cycle
bit 5 0 = CH1 ON. Channel 3 active during conversion cycle
1 = CH1 OFF. Channel 3 inactive during conversion cycle
bit 4 0 = CH1 ON. Channel 4 active during conversion cycle
1 = CH1 OFF. Channel 4 inactive during conversion cycle
bit 3:0 Not used, always reads zero
REGISTER 6-17: NEG_PWR_ACT (ADDRESS 23H)
R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0
CH1_BIDI CH2_BIDI CH3_BIDI CH4 BIDI CH1_BIDV CH2_BIDV CH3_BIDV CH4_BIDV
bit 7 bit 0
Legend:
R = Readable bit W = Writeable bit U = Unimplemented bit, read as ‘0’
-n = Value at POR ‘1’ = bit is set ‘0’ = Bit is cleared x = Bit is unknown
This register contains an image of the NEG_PWR register, 1Dh.The bits in this register reflect the current active value
of these settings, whereas the values in register 1Dh may have been programmed but not activated by one of the
REFRESH commands. This register allows software to determine the actual active setting. This register is valid when
the Results registers are valid, 1 ms after a REFRESH/_V/_G command.
bit 7:0 These bits show the current active value of these bits
bit 7 0 = Channel 1 VSENSE ADC converts 0 to +100 mV range with 16-bit straight binary output
1 = Channel 1 VSENSE ADC converts –100 mV to +100 mV range with 16-bit two’s complement output
bit 6 0 = Channel 2 VSENSE ADC converts 0 to +100 mV range with 16-bit straight binary output
1 = Channel 2 VSENSE ADC converts –100 mV to +100 mV range with 16-bit two’s complement output
bit 5 0 = Channel 3 VSENSE ADC converts 0 to +100 mV range with 16-bit straight binary output
1 = Channel 3 VSENSE ADC converts –100 mV to +100 mV range with 16-bit two’s complement output
bit 4 0 = Channel 4 VSENSE ADC converts 0 to +100 mV range with 16-bit straight binary output
1 = Channel 4 VSENSE ADC converts –100 mV to +100 mV range with 16-bit two’s complement output
bit 3 0 = Channel 1 VBUS ADC converts 0 to +32V range with 16-bit straight binary output
1 = Channel 1 VBUS ADC converts –32V to +32V range with 16-bit two’s complement output
bit 2 0 = Channel 2 VBUS ADC converts 0 to +32V range with 16-bit straight binary output
1 = Channel 2 VBUS ADC converts –32V to +32V range with 16-bit two’s complement output
PAC1934
DS20005850B-page 44 2017 Microchip Technology Inc.
bit 1 0 = Channel 3 VBUS ADC converts 0 to +32V range with 16-bit straight binary output
1 = Channel 3 VBUS ADC converts –32V to +32V range with 16-bit two’s complement output
bit 0 0 = Channel 4 VBUS ADC converts 0 to +32V range with 16-bit straight binary output
1 = Channel 4 VBUS ADC converts –32V to +32V range with 16-bit two’s complement output
REGISTER 6-18: CTRL_LAT REGISTER (ADDRESS 24H)
R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0
Sample_Rate<1:0> SLEEP SING ALERT_PIN ALERT_CC OVF ALERT OVF
bit 7 bit 0
Legend:
R = Readable bit W = Writeable bit U = Unimplemented bit, read as ‘0’
-n = Value at POR ‘1’ = bit is set ‘0’ = Bit is cleared x = Bit is unknown
This register contains an image of the Register 6-15 CTRL_ACT Register (Address 21h). The bits in this register reflect
the value of these settings that was active before the most recent REFRESH command (including REFRESH_V and/or
REFRESH_G). The values in register 01h may have been programmed but not activated by one of the REFRESH
commands, and the values in 21h are currently active. This register allows software to determine the actual active set-
ting that was active prior to the most recent REFRESH command and therefore corresponds to the dataset that is held
in the readable registers. This register is valid when the Results registers are valid, 1 ms after a REFRESH/_V/_G
command.
bit 7:6 Sample_Rate<1:0> – shows the value of these settings that was latched prior to the most recent
REFRESH command (including REFRESH_V and/or REFRESH_G)
00b = 1024 samples/s
01b = 256 samples/s
10b = 64 samples/s
11b = 8 samples/s
bit 5 SLEEP: This bit shows the value of these settings that was latched prior to the most recent REFRESH
command (including REFRESH_V and/or REFRESH_G).
0 = Active mode
1 = SLEEP mode, no data conversion
bit 4 SING: this bit shows the value of these settings that was latched prior to the most recent REFRESH
command (including REFRESH_V and/or REFRESH_G).
0 = Sequential scan mode
1 = Single-shot mode
bit 3 the value of these settings that was latched prior to the most recent REFRESH command (including
REFRESH_V and/or REFRESH_G).
0 = Disable the ALERT pin function
1 = Enable the ALERT pin function
bit 2 This bit shows the value of these settings that was latched prior to the most recent REFRESH command
(including REFRESH_V and/or REFRESH_G) for the ALERT_CC bit.
0 = No ALERT on Conversion Cycle Complete
1 = ALERT function asserted for 5uS on each completion of the conversion cycle.
bit 1 This bit shows the value of these settings that was latched prior to the most recent REFRESH command
(including REFRESH_V and/or REFRESH_G) for the ALERT_CC bit.
0 = No ALERT if accumulator or accumulator counter overflow has occurred.
1 = ALERT pin triggered if accumulator or accumulator counter has overflowed.
bit 0 This bit shows the value of these settings that was latched prior to the most recent REFRESH command
(including REFRESH_V and/or REFRESH_G) for the OVF bit.
0 = No accumulator or accumulator counter overflow has occurred.
1 = accumulator or accumulator counter has overflowed
REGISTER 6-17: NEG_PWR_ACT (ADDRESS 23H) (CONTINUED)
2017 Microchip Technology Inc. DS20005850B-page 45
PAC1934
REGISTER 6-19: CHANNEL DIS_LAT (ADDRESS 25H)
R-0 R-0 R-0 R-0 U U U U
CH1_OFF CH2_OFF CH3_OFF CH4_OFF ————
bit 7 bit 0
Legend:
R = Readable bit W = Writeable bit U = Unimplemented bit, read as ‘0’
-n = Value at POR ‘1’ = bit is set ‘0’ = Bit is cleared x = Bit is unknown
This register contains an image of the Register 6-16 Channel DIS_ACT (Address 22h).The bits in this register reflect
the value of these settings that was active before the most recent REFRESH command (including REFRESH_V and/or
REFRESH_G). The values in register 1Ch may have been programmed but not activated by one of the REFRESH
commands, and the values in 22h are currently active. This register allows software to determine the actual active set-
ting that was active prior to the most recent REFRESH command and therefore corresponds to the dataset that is held
in the readable registers. This register is valid when the Results registers are valid, 1 ms after a REFRESH/_V/_G
command.
bit <7:4> The value of these settings that was latched prior to the most recent REFRESH command (including
REFRESH_V and/or REFRESH_G)
bit 7 0 = CH1 ON. Channel 1 active during conversion cycle
1 = CH1 OFF. Channel 1 inactive during conversion cycle
bit 6 0 = CH1 ON. Channel 2 active during conversion cycle
1 = CH1 OFF. Channel 2 inactive during conversion cycle
bit 5 0 = CH1 ON. Channel 3 active during conversion cycle
1 = CH1 OFF. Channel 3 inactive during conversion cycle
bit 4 0 = CH1 ON. Channel 4 active during conversion cycle
1 = CH1 OFF. Channel 4 inactive during conversion cycle
bit 3:0 Not used, always read 0
REGISTER 6-20: NEG_PWR _LAT (ADDRESS 26H)
R-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0
CH1_BIDI CH2_BIDI CH3_BIDI CH4 BIDI CH1_BIDV CH2_BIDV CH3_BIDV CH4_BIDV
bit 7 bit 0
Legend:
R = Readable bit W = Writeable bit U = Unimplemented bit, read as ‘0’
-n = Value at POR ‘1’ = bit is set ‘0’ = Bit is cleared x = Bit is unknown
This register contains an image of the Register 6-17 NEG_PWR_ACT (Address 23h).The bits in this register reflect
the value of these settings that was active before the most recent REFRESH command (including REFRESH_V and/or
REFRESH_G). The values in register 1Dh may have been programmed but not activated by one of the REFRESH
commands, and the values in 23h are currently active. This register allows software to determine the actual active set-
ting that was active prior to the most recent REFRESH command and therefore corresponds to the dataset that is held
in the readable registers. This register is valid when the Results registers are valid, 1 ms after a REFRESH/_V/_G
command.
bit 7:0 The value of these settings that was latched prior to the most recent REFRESH command (including
REFRESH_V and/or REFRESH_G)
bit 7 0 = Channel 1 VSENSE ADC converts 0 to +100mV range with 16-bit straight binary output
1 = Channel 1 VSENSE ADC converts –100mV to +100mV range with 16 bit two’s complement output
bit 6 0 = Channel 2 VSENSE ADC converts 0 to +100mV range with 16-bit straight binary output
1 = Channel 2 VSENSE ADC converts –100mV to +100mV range with 16-bit two’s complement output
bit 5 0 = Channel 3 VSENSE ADC converts 0 to +100mV range with 16-bit straight binary output
1 = Channel 3 VSENSE ADC converts –100mV to +100mV range with 16-bit two’s complement output
PAC1934
DS20005850B-page 46 2017 Microchip Technology Inc.
bit 4 0 = Channel 4 VSENSE ADC converts 0 to +100mV range with 16-bit straight binary output
1 = Channel 4 VSENSE ADC converts –100mV to +100mV range with 16-bit two’s complement output
bit 3 0 = Channel 1 VBUS ADC converts 0 to +32V range with 16-bit straight binary output
1 = Channel 1 VBUS ADC converts –32V to +32V range with 16-bit two’s complement output
bit 2 0 = Channel 2 VBUS ADC converts 0 to +32V range with 16-bit straight binary output
1 = Channel 2 VBUS ADC converts –32V to +32V range with 16-bit two’s complement output
bit 1 0 = Channel 3 VBUS ADC converts 0 to +32V range with 16-bit straight binary output
1 = Channel 3 VBUS ADC converts –32V to +32V range with 16-bit two’s complement output
bit 0 0 = Channel 4 VBUS ADC converts 0 to +32V range with 16-bit straight binary output
1 = Channel 4 VBUS ADC converts –32V to +32V range with 16-bit two’s complement output
REGISTER 6-21: PRODUCT ID REGISTER (ADDRESS FDh)
R-0 R-1 R-0 R-1 R-1 R-0 R-1 R-1
PID<7:0>
bit 7 bit 0
Legend:
R = Readable bit W = Writeable bit U = Unimplemented bit, read as ‘0’
-n = Value at POR ‘1’ = bit is set ‘0’ = Bit is cleared x = Bit is unknown
bit 7:0 PID<7:0>: This register contains the Product ID for the PAC1934. This register is writable only when it
is unlocked for test mode, always readable.
0101_1011 for PAC1934 (Default shown in table directly above)
REGISTER 6-22: MANUFACTURER ID REGISTER (ADDRESS FEh)
R-0 R-1 R-0 R-1 R-1 R-1 R-0 R-1
MID<7:0>
bit 7 bit 0
Legend:
R = Readable bit W = Writeable bit U = Unimplemented bit, read as ‘0’
-n = Value at POR ‘1’ = bit is set ‘0’ = Bit is cleared x = Bit is unknown
bit 7:0 MID<7:0>: The Manufacturer ID register identifies Microchip as the manufacturer of the PAC1934
This value is 5Dh.
REGISTER 6-20: NEG_PWR _LAT (ADDRESS 26H) (CONTINUED)
2017 Microchip Technology Inc. DS20005850B-page 47
PAC1934
REGISTER 6-23: REVISION ID REGISTER (ADDRESS FFh)
R-0 R-0 R-0 R-0 R-0 R-0 R-1 R-1
RID<7:0>
bit 7 bit 0
Legend:
R = Readable bit W = Writeable bit U = Unimplemented bit, read as ‘0’
-n = Value at POR ‘1’ = bit is set ‘0’ = Bit is cleared x = Bit is unknown
bit 7:0 RID<7:0>: The Revision register identifies the die revision
This register reads 03h.
PAC1934
DS20005850B-page 48 2017 Microchip Technology Inc.
7.0 PACKAGE DESCRIPTION
7.1 Package Marking Information
Legend: XX...X Customer-specific information
Y Year code (last digit of calendar year)
YY Year code (last 2 digits of calendar year)
WW Week code (week of January 1 is week ‘01’)
NNN Alphanumeric traceability code
Pb-free JEDEC® designator for Matte Tin (Sn)
*This package is Pb-free. The Pb-free JEDEC designator ( )
can be found on the outer packaging for this package.
Note: In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
3
e
3
e
WLCSP-16 Example
934
725
2017 Microchip Technology Inc. DS20005850B-page 49
PAC1934
%
$
 &
 &
 & $ %
 &
'$780%
'$780$
&
6($7,1*
3/$1(
$
%
;
7239,(:
6,'(9,(:
%277209,(:
127(
$
%
0LFURFKLS7HFKQRORJ\'UDZLQJ&5HY%6KHHWRI
;
)RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW
KWWSZZZPLFURFKLSFRPSDFNDJLQJ
1RWH
%DOO:DIHU/HYHO&KLS6FDOH3DFNDJH&6[PP%RG\>:/&63@
'
(
H(
H'
H'
&
'

&
'

;E
$$ $
 &
;
H(
3$&
PAC1934
DS20005850B-page 50 2017 Microchip Technology Inc.
0LFURFKLS7HFKQRORJ\'UDZLQJ&5HY%6KHHWRI
%DOO:DIHU/HYHO&KLS6FDOH3DFNDJH&6[PP%RG\>:/&63@
)RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW
KWWSZZZPLFURFKLSFRPSDFNDJLQJ
1RWH
2YHUDOO+HLJKW
%XPS'LDPHWHU
%XPS3LWFK
:LGWK
/HQJWK
%XPS3LWFK
$
E
0,1'LPHQVLRQ/LPLWV
'
(
H(
8QLWV
H'
0,//,0(7(56
%6&
%6&
%6&
120
%6&
0$;
 
 
'LH7KLFNQHVV $  
5()5HIHUHQFH'LPHQVLRQXVXDOO\ZLWKRXWWROHUDQFHIRULQIRUPDWLRQSXUSRVHVRQO\
%6&%DVLF'LPHQVLRQ7KHRUHWLFDOO\H[DFWYDOXHVKRZQZLWKRXWWROHUDQFHV



Notes:
7RSVLGH$LQGLFDWRULVDQHQJUDYHGILJXUH
8QGHUILOOLVUHFRPPHQGHGIRUEHVWVROGHUMRLQWUHOLDELOLW\
'LPHQVLRQLQJDQGWROHUDQFLQJSHU$60(<0
 6ROGHUGLDPHWHUDWLQWHUIDFHWRSDFNDJHERG\LVPQRPLQDO
3$&
%XPS+HLJKW $  
2017 Microchip Technology Inc. DS20005850B-page 51
PAC1934
5(&200(1'('/$1'3$77(51
0LFURFKLS7HFKQRORJ\'UDZLQJ&5HY%
%DOO:DIHU/HYHO&KLS6FDOH3DFNDJH&6[PP%RG\>:/&63@
6,/.6&5((1
%6&%DVLF'LPHQVLRQ7KHRUHWLFDOO\H[DFWYDOXHVKRZQZLWKRXWWROHUDQFHV
1RWHV
'LPHQVLRQLQJDQGWROHUDQFLQJSHU$60(<0
)RUEHVWVROGHULQJUHVXOWVWKHUPDOYLDVLIXVHGVKRXOGEHILOOHGRUWHQWHGWRDYRLGVROGHUORVVGXULQJ
UHIORZSURFHVV


)RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW
KWWSZZZPLFURFKLSFRPSDFNDJLQJ
1RWH
3$&
H'
H(
'
(
*
*
;
'
&
%
$

6SDFH%HWZHHQ&RQWDFWV
&RQWDFW'LDPHWHU
6SDFH%HWZHHQ&RQWDFWV
&RQWDFW3LWFK
2YHUDOO3LWFK
2YHUDOO3LWFK
&RQWDFW3LWFK
*
;
*


0,1'LPHQVLRQ/LPLWV
'
(
H(
8QLWV
H'
0,//,0(7(56
%6&
%6&
%6&
120
%6&
0$;
PAC1934
DS20005850B-page 52 2017 Microchip Technology Inc.
NOTES:
2017 Microchip Technology Inc. DS20005850B-page 53
PAC1934
APPENDIX A: REVISION HISTORY
Revision B (November 2017)
The following is the list of modifications:
1. Updated Section 4.5 “V olt age Measurement”,
Section 4.6 “Current Measurement”,
Section 4.7 “Selecting RSENSE Values” and
Section 4.9 “Power and Energy”.
2. Updated Register 6-10.
3. Fixed minor typographical errors.
Revision A (September 2017)
• Initial Release for Advance Data Sheet.
PAC1934
DS20005850B-page 54 2017 Microchip Technology Inc.
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
PART NO. X-X /XXX
Tape and Temperature
Device
Device: PAC1934: DC Power/Energy Monitor with Accumulator
Tape and Reel: T = Tape and Reel
Temperature
Range: I = -40C to +85C (Industrial)
Package: 6CX = 16-Ball Wafer Level Chip Scale Package,
2.225 mm x 2.17 mm (WLCSP)
J6CX = This part number is being phased out and it is identi-
cal to the 6CX package.
Reel Range Package Example:
a) PAC1934T-I/6CX: 16-lead 2.225 mm x 2.17 mm
WLCSP, shipped in a 5,000
piece Tape and Reel
Note 1: Tape and Reel identifier only appears in the
catalog part number description. This identi-
fier is used for ordering purposes and is not
printed on the device package. Check with
your Microchip Sales Office for package
availability with the Tape and Reel option.
2017 Microchip Technology Inc. DS20005850B-page 55
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights unless otherwise stated.
Trademarks
The Microchip name and logo, the Microchip logo, AnyRate, AVR,
AVR logo, AVR Freaks, BeaconThings, BitCloud, CryptoMemory,
CryptoRF, dsPIC, FlashFlex, flexPWR, Heldo, JukeBlox, KEELOQ,
KEELOQ logo, Kleer, LANCheck, LINK MD, maXStylus,
maXTouch, MediaLB, megaAVR, MOST, MOST logo, MPLAB,
OptoLyzer, PIC, picoPower, PICSTART, PIC32 logo, Prochip
Designer, QTouch, RightTouch, SAM-BA, SpyNIC, SST, SST
Logo, SuperFlash, tinyAVR, UNI/O, and XMEGA are registered
trademarks of Microchip Technology Incorporated in the U.S.A.
and other countries.
ClockWorks, The Embedded Control Solutions Company,
EtherSynch, Hyper Speed Control, HyperLight Load, IntelliMOS,
mTouch, Precision Edge, and Quiet-Wire are registered
trademarks of Microchip Technology Incorporated in the U.S.A.
Adjacent Key Suppression, AKS, Analog-for-the-Digital Age, Any
Capacitor, AnyIn, AnyOut, BodyCom, chipKIT, chipKIT logo,
CodeGuard, CryptoAuthentication, CryptoCompanion,
CryptoController, dsPICDEM, dsPICDEM.net, Dynamic Average
Matching, DAM, ECAN, EtherGREEN, In-Circuit Serial
Programming, ICSP, Inter-Chip Connectivity, JitterBlocker,
KleerNet, KleerNet logo, Mindi, MiWi, motorBench, MPASM, MPF,
MPLAB Certified logo, MPLIB, MPLINK, MultiTRAK, NetDetach,
Omniscient Code Generation, PICDEM, PICDEM.net, PICkit,
PICtail, PureSilicon, QMatrix, RightTouch logo, REAL ICE, Ripple
Blocker, SAM-ICE, Serial Quad I/O, SMART-I.S., SQI,
SuperSwitcher, SuperSwitcher II, Total Endurance, TSHARC,
USBCheck, VariSense, ViewSpan, WiperLock, Wireless DNA, and
ZENA are trademarks of Microchip Technology Incorporated in the
U.S.A. and other countries.
SQTP is a service mark of Microchip Technology Incorporated in
the U.S.A.
Silicon Storage Technology is a registered trademark of Microchip
Technology Inc. in other countries.
GestIC is a registered trademark of Microchip Technology
Germany II GmbH & Co. KG, a subsidiary of Microchip Technology
Inc., in other countries.
All other trademarks mentioned herein are property of their
respective companies.
© 2017, Microchip Technology Incorporated, All Rights Reserved.
ISBN: 978-1-5224-2393-5
Note the following details of the code protection feature on Microchip devices:
• Microchip products meet the specification contained in their particular Microchip Data Sheet.
• Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
• There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
• Microchip is willing to work with the customer who is concerned about the integrity of their code.
• Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Microchip received ISO/TS-16949:2009 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’ s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
devices, Serial EEPROMs, micro perip hera ls, n onvolat ile memory and
analog products . In add ition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
QUALITYMANAGEMENTS
YSTEM
CERTIFIEDBYDNV
== ISO/TS16949==
DS20005850B-page 56 2017 Microchip Technology Inc.
AMERICAS
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://www.microchip.com/
support
Web Address:
www.microchip.com
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Austin, TX
Tel: 512-257-3370
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Novi, MI
Tel: 248-848-4000
Houston, TX
Tel: 281-894-5983
Indianapolis
Noblesville, IN
Tel: 317-773-8323
Fax: 317-773-5453
Tel: 317-536-2380
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Tel: 951-273-7800
Raleigh, NC
Tel: 919-844-7510
New York, NY
Tel: 631-435-6000
San Jose, CA
Tel: 408-735-9110
Tel: 408-436-4270
Canada - Toronto
Tel: 905-695-1980
Fax: 905-695-2078
ASIA/PACIFIC
Australia - Sydney
Tel: 61-2-9868-6733
China - Beijing
Tel: 86-10-8569-7000
China - Chengdu
Tel: 86-28-8665-5511
China - Chongqing
Tel: 86-23-8980-9588
China - Dongguan
Tel: 86-769-8702-9880
China - Guangzhou
Tel: 86-20-8755-8029
China - Hangzhou
Tel: 86-571-8792-8115
China - Hong Kong SAR
Tel: 852-2943-5100
China - Nanjing
Tel: 86-25-8473-2460
China - Qingdao
Tel: 86-532-8502-7355
China - Shanghai
Tel: 86-21-3326-8000
China - Shenyang
Tel: 86-24-2334-2829
China - Shenzhen
Tel: 86-755-8864-2200
China - Suzhou
Tel: 86-186-6233-1526
China - Wuhan
Tel: 86-27-5980-5300
China - Xian
Tel: 86-29-8833-7252
China - Xiamen
Tel: 86-592-2388138
China - Zhuhai
Tel: 86-756-3210040
ASIA/PACIFIC
India - Bangalore
Tel: 91-80-3090-4444
India - New Delhi
Tel: 91-11-4160-8631
India - Pune
Tel: 91-20-4121-0141
Japan - Osaka
Tel: 81-6-6152-7160
Japan - Tokyo
Tel: 81-3-6880- 3770
Korea - Daegu
Tel: 82-53-744-4301
Korea - Seoul
Tel: 82-2-554-7200
Malaysia - Kuala Lumpur
Tel: 60-3-7651-7906
Malaysia - Penang
Tel: 60-4-227-8870
Philippines - Manila
Tel: 63-2-634-9065
Singapore
Tel: 65-6334-8870
Taiwan - Hsin Chu
Tel: 886-3-577-8366
Taiwan - Kaohsiung
Tel: 886-7-213-7830
Taiwan - Taipei
Tel: 886-2-2508-8600
Thailand - Bangkok
Tel: 66-2-694-1351
Vietnam - Ho Chi Minh
Tel: 84-28-5448-2100
EUROPE
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
Finland - Espoo
Tel: 358-9-4520-820
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
Germany - Garching
Tel: 49-8931-9700
Germany - Haan
Tel: 49-2129-3766400
Germany - Heilbronn
Tel: 49-7131-67-3636
Germany - Karlsruhe
Tel: 49-721-625370
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Germany - Rosenheim
Tel: 49-8031-354-560
Israel - Ra’anana
Tel: 972-9-744-7705
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Italy - Padova
Tel: 39-049-7625286
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Norway - Trondheim
Tel: 47-7289-7561
Poland - Warsaw
Tel: 48-22-3325737
Romania - Bucharest
Tel: 40-21-407-87-50
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
Sweden - Gothenberg
Tel: 46-31-704-60-40
Sweden - Stockholm
Tel: 46-8-5090-4654
UK - Wokingham
Tel: 44-118-921-5800
Fax: 44-118-921-5820
Worldwide Sales and Service
10/25/17