DS36C200
www.ti.com
SNLS111D –JUNE 1998–REVISED APRIL 2013
DS36C200 Dual High Speed Bi-Directional Differential Transceiver
Check for Samples: DS36C200
1FEATURES DESCRIPTION
The DS36C200 is a dual transceiver device optimized
2• Optimized for DSS to DVHS Interface Link for high data rate and low power applications. This
• Compatible IEEE 1394 Signaling Voltage device provides a single chip solution for a dual high
Levels speed bi-directional interface. Also, both control pins
• Operates Above 100 Mbps may be routed together for single bit control of
datastreams. Both control pins are adjacent to each
• Bi-directional Transceivers other for ease of routing them together. The
• 14-lead SOIC Package DS36C200 is compatible with IEEE 1394 physical
• Ultra Low Power Dissipation layer and may be used as an economical solution
with some considerations. Please reference the
• ±100 mV Receiver Sensitivity application information on 1394 for more information.
• Low Differential Output Swing Typical 210 mV The device is in a 14-lead small outline package. The
• High Impedance During Power Off differential driver outputs provides low EMI with its
low output swings typically 210 mV. The receiver
offers ±100 mV threshold sensitivity, in addition to
common-mode noise protection.
Connection Diagram
Note: * denotes active LOW pin
Figure 1. SOIC Package
See Package Number D (R-PDSO-G14)
Functional Diagram
1Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date. Copyright © 1998–2013, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
DS36C200
SNLS111D –JUNE 1998–REVISED APRIL 2013
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings(1)(2)
Supply Voltage (VCC)−0.3V to +6V
Enable Input Voltage
(DE, RE*) −0.3V to (VCC + 0.3V)
Voltage (DI/RO) −0.3V to +5.9V
Voltage (DO/RI±) −0.3V to +5.9V
Maximum Package Power Dissipation @+25°C
M Package 1255 mW
Derate M Package 10.04 mW/°C above +25°C
Storage Temperature Range −65°C to +150°C
Lead Temperature Range
(Soldering, 4 sec.) +260°C
ESD Rating (3)
(HBM, 1.5 kΩ, 100 pF) ≥3.5 kV
(EIAJ, 0 Ω, 200 pF) ≥300V
(1) “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be ensured. They are not meant to imply
that the devices should be operated at these limits. The table of “Electrical Characteristics” specifies conditions of device operation.
(2) If Military/Aerospace specified devices are required, please contact the TI Sales Office/Distributors for availability and specifications.
(3) ESD Rating: HBM (1.5 kΩ, 100 pF) ≥3.5 kV EIAJ (0Ω, 200 pF) ≥300V
Recommended Operating Conditions Min Typ Max Units
Supply Voltage (VCC) +4.5 +5.0 +5.5 V
Receiver Input Voltage 0 2.4 V
Operating Free Air
Temperature (TA) 0 25 70 °C
2Submit Documentation Feedback Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: DS36C200
DS36C200
www.ti.com
SNLS111D –JUNE 1998–REVISED APRIL 2013
Electrical Characteristics(1)(2)(3)
Over supply voltage and operating temperature ranges, unless otherwise specified
Symbol Parameter Conditions Pin Min Typ Max Units
DIFFERENTIAL DRIVER CHARACTERISTICS (RE* = VCC)
VOD Output Differential Voltage RL= 55Ω, (Figure 2) DO+, 172 210 285 mV
DO−
ΔVOD VOD Magnitude Change 0 4 35 mV
VOH Output High Voltage 1.36 V
VOL Output Low Voltage 1.15 V
VOS Offset Voltage 1.0 1.25 1.6 V
ΔVOS Offset Magnitude Change 0 5 25 mV
IOZD TRI-STATE Leakage VOUT = VCC or GND −10 ±1 +10 μA
IOXD Power-Off Leakage VOUT = 5.5V or GND, VCC = 0V −10 ±1 +10 μA
IOSD Output Short Circuit Current VOUT = 0V −4−9 mA
DIFFERENTIAL RECEIVER CHARACTERISTICS (DE = GND)
VTH Input Threshold High VCM = 0V to 2.3V RI+, +100 mV
RI−
VTL Input Threshold Low −100 mV
IIN Input Current VIN = +2.4V or 0V −10 ±1 +10 μA
VOH Output High Voltage IOH =−400 μA RO 3.8 4.9 V
Inputs Open 3.8 4.9 V
Inputs Terminated, Rt= 55Ω3.8 4.9 V
Inputs Shorted, VID = 0V 4.9 V
VOL Output Low Voltage IOL = 2.0 mA, VID =−200 mV 0.1 0.4 V
IOSR Output Short Circuit Current VOUT = 0V −15 −60 −100 mA
DEVICE CHARACTERISTICS
VIH Input High Voltage DI, DE 2.0 VCC V
RE*
VIL Input Low Voltage GND 0.8 V
IIH Input High Current VIN = VCC or 2.4V ±1 ±10 μA
IIL Input Low Current VIN = GND or 0.4V ±1 ±10 μA
VCL Input Clamp Voltage ICL =−18 mA −1.5 −0.8 V
ICCD Power Supply Current No Load, DE = RE* = VCC VCC 3 7 mA
RL= 55Ω, DE = RE* = VCC 11 17 mA
ICCR DE = RE* = 0V 6 10 mA
(1) Current into device pins is defined as positive. Current out of device pins is defined as negative. All voltages are referenced to ground
except VOD and VID.
(2) All typicals are given for VCC = +5.0V and TA= +25°C.
(3) The DS36C200 is a current mode device and only function with datasheet specification when a resistive load is applied to the drivers
outputs.
Copyright © 1998–2013, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: DS36C200
DS36C200
SNLS111D –JUNE 1998–REVISED APRIL 2013
www.ti.com
Switching Characteristics
Over supply voltage and operating temperature ranges, unless otherwise specified. (1) (2)
Symbol Parameter Conditions Min Typ Max Units
DIFFERENTIAL DRIVER CHARACTERISTICS
tPHLD Differential Propagation Delay High to Low RL= 55Ω, CL= 10 pF 1.0 2.5 5.5 ns
(Figure 3 and Figure 4)
tPLHD Differential Propagation Delay Low to High 1.0 2.6 5.5 ns
tSKD Differential Skew |tPHLD – tPLHD| 0 0.1 2 ns
tTLH Transition Time Low to High 0 0.5 2 ns
tTHL Transition Time High to Low 0 0.5 2 ns
tPHZ Disable Time High to Z RL= 55Ω0.3 5 20 ns
(Figure 5 and Figure 6)
tPLZ Disable Time Low to Z 0.3 5 20 ns
tPZH Enable Time Z to High 0.3 10 30 ns
tPZL Enable Time Z to Low 0.3 10 30 ns
DIFFERENTIAL RECEIVER CHARACTERISTICS
tPHLD Differential Propagation Delay High to Low CL= 10 pF, VID = 200 mV 1.5 5 9 ns
(Figure 7 and Figure 8)
tPLHD Differential Propagation Delay Low to High 1.5 4.6 9 ns
tSKD Differential Skew |tPHLD – tPLHD| 0 0.4 3 ns
trRise Time 0 1.5 5 ns
tfFall Time 0 1.5 5 ns
tPHZ Disable Time High to Z CL= 10 pF 1 5 20 ns
(Figure 9 and Figure 10)
tPLZ Disable Time Low to Z 1 5 20 ns
tPZH Enable Time Z to High 0.3 10 30 ns
tPZL Enable Time Z to Low 0.3 10 30 ns
(1) CLincludes probe and fixture capacitance.
(2) Generator waveform for all tests unless otherwise specified: f = 1 MHz, ZO= 50Ω, tr≤1 ns, tf≤1 ns (0%–100%).
4Submit Documentation Feedback Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: DS36C200
DS36C200
www.ti.com
SNLS111D –JUNE 1998–REVISED APRIL 2013
PARAMETER MEASUREMENT INFORMATION
Figure 2. Differential Driver DC Test Circuit
Figure 3. Differential Driver Propagation Delay and Transition Time Test Circuit
Figure 4. Differential Driver Propagation Delay and Transition Time Waveforms
Figure 5. Driver TRI-STATE Delay Test Circuit
Copyright © 1998–2013, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: DS36C200
DS36C200
SNLS111D –JUNE 1998–REVISED APRIL 2013
www.ti.com
Figure 6. Driver TRI-STATE Delay Waveforms
Figure 7. Receiver Propagation Delay and Transition Time Test Circuit
Figure 8. Receiver Propagation Delay and Transition Time Waveforms
Figure 9. Receiver TRI-STATE Delay Test Circuit
Figure 10. Receiver TRI-STATE Delay Waveforms
6Submit Documentation Feedback Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: DS36C200
DS36C200
www.ti.com
SNLS111D –JUNE 1998–REVISED APRIL 2013
APPLICATION INFORMATION
TRUTH TABLES
The DS36C200 has two enable pins DE and RE*, however, the driver and receiver should never be enabled
simultaneously. Enabling both could cause multiple channel contention between the receiver output and the
driving logic. It is recommended to route the enables together on the PC board. This will allow a single bit
[DE/RE*] to control the chip. This DE/RE* bit toggles the DS36C200 between Receive mode and Transmit mode.
When the bit is asserted HIGH the device is in Transmit mode. When the bit is asserted LOW the device is in
Receive mode. The mode determines the function of the I/O pins: DI/RO, DO/RI+, and DO/RI−. Please note that
some of the pins have been identified by its function in the corresponding mode in the three tables below. For
example, in Transmit mode the DO/RI+ pin is identified as DO+. This was done for clarity in the tables only and
should not be confused with the pin identification throughout the rest of this document. Also note that a logic low
on the DE/RE* bit corresponds to a logic low on both the DE pin and the RE* pin. Similarly, a logic high on the
DE/RE* bit corresponds to a logic high on both the DE pin and the RE* pin.
Table 1. Receive Mode(1)
Input(s) Input/Output
DE RE* [RI+] −[RI−] RO
L L > +100 mV H
L L < −100 mV L
L L 100 mV > & > −100 mV X
L H X Z
(1) H = Logic high level
L = Logic low level
X = Indeterminate state
Z = High impedance state
Table 2. Transmit Mode(1)
Input(s) Input/Output
DE RE* DI DO+ DO−
H H L L H
H H H H L
H H 2 > & > 0.8 X X
L H X Z Z
(1) H = Logic high level
L = Logic low level
X = Indeterminate state
Z = High impedance state
Copyright © 1998–2013, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Links: DS36C200
DS36C200
SNLS111D –JUNE 1998–REVISED APRIL 2013
www.ti.com
DEVICE PIN DESCRIPTIONS
Pin# Name Mode Description
(In mode only)
3 DE Transmit Driver Enable: When asserted low driver is disabled. And when asserted
high driver is enabled.
1, 7 DI TTL/CMOS driver input pins
10, 13 DO+ Non-inverting driver output pin
11, 12 DO−Inverting driver output pin
4 RE* Receive Receiver Enable: When asserted low receiver is enabled. And when
asserted high receiver is disabled.
1, 7 RO Receiver output pin
10, 13 RI+ Positive receiver input pin
11, 12 RI−Negative receiver input pin
5 GND Transmit and Ground pin
2 VCC Receive Positive power supply pin, +5V ± 10%
6, 8, 9, 14 NC No Connect
IEEE 1394
The DS36C200 drives and receives IEEE 1394 physical layer signal levels. The current mode driver is capable of
driving a 55Ωload with VOD between 172 mV and 285 mV. The DS36C200 is not designed to work with a link
layer controller IC requiring full 1394 physical layer compliancy to the standard. No clock generator, no
arbitration, and no encode/decode logic is provided with this device. For a 1394 link where speed sensing, bus
arbitration, and other functions are not required, a controller and the DS36C200 will provide a cost effective, high
speed dedicated link. This is shown in Figure 11. In applications that require fully compliant 1394 protocol, a link
layer controller and physical layer controller will be required as shown in Figure 11. The physical layer controller
supports up to three DC36C200 devices (not shown).
The DS36C200 drivers are current mode drivers and intended to work with a two 110Ωtermination resistors in
parallel with each other. The termination resistors should match the characteristic impedance of the transmission
media. The drivers are current mode devices therefore the resistors are required. Both resistors are required for
half duplex operation and should be placed as close to the DO/RI+ and DO/RI−pins as possible at opposite
ends of the bus. However, if your application only requires simplex operation, only one termination resistor is
required. In addition, note the voltage levels will vary from those in the datasheet due to different loading. Also,
AC or unterminated configurations are not used with this device. Multiple node configurations are possible as
long as transmission line effects are taken into account. Discontinuities are caused by mid-bus stubs,
connectors, and devices that affect signal integrity.
The differential line driver is a balanced current source design. A current mode driver, generally speaking has a
high output impedance and supplies a constant current for a range of loads (a voltage mode driver on the other
hand supplies a constant voltage for a range of loads). Current is switched through the load in one direction to
produce a logic state and in the other direction to produce the other logic state. The typical output current is mere
3.8 mA, a minimum of 3.1 mA, and a maximum of 5.2 mA. The current mode requires that a resistive
termination be employed to terminate the signal and to complete the loop as shown in Figure 12. The 3.8 mA
loop current will develop a differential voltage of 210 mV across the 55Ωtermination resistor which the receiver
detects with a 110 mV minimum differential noise margin neglecting resistive line losses (driven signal minus
receiver threshold (210 mV – 100 mV = 110 mV)). The signal is centered around +1.2V (Driver Offset, VOS) with
respect to ground as shown in Figure 8.
The current mode driver provides substantial benefits over voltage mode drivers, such as an RS-422 driver. Its
quiescent current remains relatively flat versus switching frequency. Whereas the RS-422 voltage mode driver
increases exponentially in most case between 20 MHz–50 MHz. This is due to the overlap current that flows
between the rails of the device when the internal gates switch. Whereas the current mode driver switches a fixed
current between its output without any substantial overlap current. This is similar to some ECL and PECL
devices, but without the heavy static ICC requirements of the ECL/PECL designs. LVDS requires > 80% less
current than similar PECL devices. AC specifications for the driver are a tenfold improvement over other existing
RS-422 drivers.
8Submit Documentation Feedback Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: DS36C200
DS36C200
www.ti.com
SNLS111D –JUNE 1998–REVISED APRIL 2013
Fail-safe Feature:
The LVDS receiver is a high gain, high speed device that amplifies a small differential signal (20mV) to CMOS
logic levels. Due to the high gain and tight threshold of the receiver, care should be taken to prevent noise from
appearing as a valid signal.
The receiver's internal fail-safe circuitry is designed to source/sink a small amount of current, providing fail-safe
protection (a stable known state of HIGH output voltage) for floating, terminated or shorted receiver inputs.
1. Open Input Pins. The DS36C200 is a dual transceiver device, and if an application requires only one
receiver, the unused channel inputs should be left OPEN. Do not tie the receiver inputs to ground or any
other voltages. The input is biased by internal high value pull up or pull down resistors to set the output to a
HIGH state. This internal circuitry will ensure a HIGH, stable output state for open inputs.
2. Terminated Input. If the driver is disconnected (cable unplugged), or if the driver is in a TRI-STATE or
power-off condition, the receiver output will again be in a HIGH state, even with the end of the cable 100Ω
termination resistor across the input pins. The unplugged cable can become a floating antenna which can
pick up noise. If the cable picks up more than 10mV of differential noise, the receiver may see the noise as a
valid signal and switch. To insure that any noise is seen as common-mode and not differential, a balanced
interconnect should be used. Twisted pair cable will offer better balance than flat ribbon cable.
3. Shorted Inputs. If a fault condition occurs that shorts the receiver inputs together, thus resulting in a 0V
differential input voltage, the receiver output will remain in a HIGH state. Shorted input fail-safe is not
supported across the common-mode range of the device (GND to 2.4V). It is only supported with inputs
shorted and no external common-mode voltage applied.
If there is more than 10mV of differential noise, the receiver may switch or oscillate. If this condition can happen
in your application, you may wish to add external fail-safe resistors to create a larger noise margin. External
lower value pull up and pull down resistors (for a stronger bias) may be used to boost fail-safe in the presence of
higher noise levels. The pull up and pull down resistors should be in the 5kΩto 15kΩrange to minimize loading
and waveform distortion to the driver. The common-mode bias point should be set to approximately 1.2V (less
than 1.75V) to be compatible with the internal circuitry.
Additional information on fail-safe biasing of LVDS devices may be found in AN-1194 (SNLA051).
Figure 11. (A) Dedicated IEEE 1394 Link
(B) Full IEEE 1394 Compliant Link
Copyright © 1998–2013, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Links: DS36C200
DS36C200
SNLS111D –JUNE 1998–REVISED APRIL 2013
www.ti.com
Figure 12. Typical in Home Application
Figure 13. Typical Interface Connection (1)
(1) The DS36C200 is a current mode device and only function with datasheet specification when a resistive load is applied to the drivers
outputs.
10 Submit Documentation Feedback Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: DS36C200
DS36C200
www.ti.com
SNLS111D –JUNE 1998–REVISED APRIL 2013
REVISION HISTORY
Changes from Revision C (April 2013) to Revision D Page
• Changed layout of National Data Sheet to TI format .......................................................................................................... 10
Copyright © 1998–2013, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Links: DS36C200
PACKAGE OPTION ADDENDUM
www.ti.com 7-Oct-2013
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
DS36C200M/NOPB ACTIVE SOIC D 14 55 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 DS36C200M
DS36C200MX/NOPB ACTIVE SOIC D 14 2500 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 DS36C200M
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
DS36C200MX/NOPB SOIC D 14 2500 330.0 16.4 6.5 9.35 2.3 8.0 16.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 23-Sep-2013
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
DS36C200MX/NOPB SOIC D 14 2500 367.0 367.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 23-Sep-2013
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2016, Texas Instruments Incorporated
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Texas Instruments:
DS36C200M/NOPB DS36C200MX/NOPB