6.0 Amps Single Phase Full Wave Bridge Rectifier
IO(AV) = 6A
VRRM = 50/ 800V
6GBU Series
1
Bulletin I2718 rev. E 05/02
www.irf.com
Features
Diode chips are glass passivated
Suitable for Universal hole mounting
Easy to assemble & install on P.C.B.
High Surge Current Capability
High Isolation between terminals and molded case (1500 VRMS)
Lead free terminals solderable as per MIL-STD-750 Method 2026
Terminals suitable for high temperature soldering at 260°C for 8-10 secs
UL E160375 approved
Description
These GBU Series of Single Phase Bridges consist
of four glass passivated silicon junction connected
as a Full Wave Bridge. These four junctions are
encapsulated by plastic molding technique. These
Bridges are mainly used in Switch Mode power
supply and in industrial and consumer equipment.
Parameters 6GBU Units
Major Ratings and Characteristics
IO6A
@ TC100 °C
IFSM @
50Hz 175 A
@ 60Hz 182 A
I2t @ 50Hz 154 A2s
@ 60Hz 138 A2s
VRRM range 50 to 800 V
TJ- 55 to 150 oC
6GBU
PART OBSOLETE - EOL18
6GBU Series
2
Bulletin I2718 rev. E 05/01
www.irf.com
IOMaximum DC output current 6.0 A TC = 100°C, Resistive & inductive load
4.8 TC = 100°C, Capacitive load
IFSM Maximum peak, one-cycle 175 t = 10ms
non-repetitive surge current,
following any rated load condition 182 t = 8.3ms TJ = 150°C
and with rated VRRM reapplied
I2t Maximum I2t for fusing, 154 A2s t = 10ms
initial TJ = TJ max 138 t = 8.3ms
VFM Maximum peak forward voltage 1.0 V TJ = 25 oC, IFM = 6A
per diode
IRM Typical peak reverse leakage 5.0 µA TJ = 2 5 oC, 100% VRRM
curren t per diode 400 TJ = 150 oC, 100% VRRM
VRRM Maximum repetitive peak 50 to 800 V
reverse voltage range
Forward Conduction
Voltage VRRM , max repetitive VRMS , max RMS IRRM max. IRRM max.
Type number Code peak rev. voltage voltage @ rated VRRM @ rated VRRM
TJ = TJ max. TJ = TJ max. TJ = 25°C TJ = 150°C
V V µA µA
6GBU 005 50 35 5 400
01 100 70 5 400
02 200 140 5 400
04 400 280 5 400
06 600 420 5 400
08 800 560 5 400
ELECTRICAL SPECIFICATIONS
Voltage Ratings
Parameters 6GBU Unit Conditions
Thermal and Mechanical Specifications
Note (1): Bridge mounted on Aluminum heat sink of dim 65 x 35 x 1.5mm, use silicon thermal compound heat
transfer and bolt down using 3mm screw
TJOperating and storage -55 to 150 oC
Tstg temperature range
RthJC Max. thermal resistance 2.2 °C/ W DC rated current through bridge (1)
junction to case
RthJA Thermal resistance, 7.4 °C/ W DC rated current through bridge (1)
junction to ambient
W Approximate weight 4 (0.14) g (oz)
T Mounting Torque 1.0 Nm Bridge to Heatsink
9.0 Lb.in
Parameters 6GBU Unit Conditions
6GBU Series
3
Bulletin I2718 rev. E 05/02
www.irf.com
1- Bridge current
2- Basic Part Number
3- Voltage Code: code x 100 = VRRM
6 GBU 08
1 2
Ordering Information Table
Device Code
Outline Table
All dimensions are in millimetres
3
6GBU Series
4
Bulletin I2718 rev. E 05/01
www.irf.com
Fig. 2 - Forward Voltage Drop Characteristics
Fig. 1 - Current Ratings Characteristics
Fig. 4 - Maximum Non-Repetitive Surge Current
Instantaneous Forward Voltage (V)
Instantaneous Forward Current (A)
Maximum Allowable Case Temperature (°C)
Average Forward Current (A)
Number of Equal Amplitude Half Cycle Current Pulses (N)
Peak Half Sine Wave Forward Current (A)
Fig. 3 - Total Power Loss Characteristics
Maximum Average Forward Power Loss (W)
Average Forward Current (A)
90
100
110
120
130
140
150
160
01234567
180˚
(Sine)
180˚
(Rect)
6GBU Series
0.1
1
10
100
1000
0.5 1 1.5 2 2.5 3
T = 25˚C
J
T = 150˚C
J
6GBU Series
0
2
4
6
8
10
12
0123456
180˚
(Sine)
180˚
(Rect)
6GBU Series
T = 150˚C
J
40
60
80
100
120
140
160
180
200
1 10 100
At Any Rated Load Condition And With
Rated Vrrm Applied Following Surge.
Initial Tj = 150˚C
@ 60 Hz 0.0083 s
@ 50 Hz 0.0100 s
6GBU Series
6GBU Series
5
Bulletin I2718 rev. E 05/02
www.irf.com
IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105
TAC Fax: (310) 252-7309
Visit us at www.irf.com for sales contact information. 05/02
Data and specifications subject to change without notice.
This product has been designed and qualified for Multiple Level.
Qualification Standards can be found on IR's Web site.
