17More information online at bannerengineering.com
SAFETY LIGHT SCREENS
SAFETY
LIGHT SCREENS
Safety Light Screens
EZ-SCREEN® . . . . . . . . . . . . . . . . . . . . . . . .page 20
• Provides point-of-operation, area, access and perimeter
safeguarding.
• Protects personnel from injury and equipment from damage.
• Offered with 14 and 30 mm resolution, single-beam points,
or multi-beam grids.
• Requires no controller.
• Rated Type 4.
• Available with optional ESD-safe housing, pigtail connectors
and cascading on some models.
• Reduced resolution and fixed blanking on EZ-SCREEN Type 4.
MINI-SCREEN®
. . . . page 58
• Suitable for heavy-duty machine guarding
applications —extra robust housing
available.
• Features rugged, compact emitters and
receivers ranging from 114 to 1829 mm
long, depending on series and model.
• Includes floating blanking and selectable
auto power-up.
• Offers optional fixed-beam blanking and
muting.
• Offered with yellow or black housing on
emitters and receivers.
PICO-GUARD™
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 36
• Provides access and short-range perimeter guarding.
• Offers low-cost alternative to cumbersome machine guarding methods.
• Combines fiber optic and photoelectric technologies.
• Uses fiber optic technology for intrinsically safe guarding in explosive or harsh environments.
• Installs easily using inexpensive plastic fiber optics.
MICRO-SCREEN®
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 42
• Designed for light- to medium-duty production machinery.
• Features ultra-compact emitters and receivers ranging from 102 to 1829 mm long, depending on series and model.
• Offered with optional ESD-safe housing.
• Includes floating blanking and optional fixed blanking.
• Controllers offered with DeviceNet™, E-stop input and muting.
EZ-SCREEN® Type 2 . page 78
• Designed for lower-risk applications.
• Provides economical, compact optical
safeguarding.
• Meets Type 2 requirements per
IEC 61496-1/-2.
• Offered with 30 mm resolution and
15 m range.
18 More information online at bannerengineering.com
SAFETY LIGHT SCREENS
SAFETY
LIGHT SCREENS
Catalog Safety Supply Maximum
Type Model Page Category Resolution Voltage Range
SAFETY LIGHT SCREEN SELECTION
EZ-SCREEN®
Standard Systems
Page 20 4
14 & 30 mm
24V dc
18 m
Cascade Systems 14 & 30 mm 18 m
Grid & Point Systems 300 to 584 mm
(beam spacing) 70 m
PICO-GUARD™
Grid Systems
Page 36 4
300 to 584 mm
(beam spacing)
24V dc 31 m
Point Systems —
MICRO-SCREEN®
Emitters & Receivers
Page 42 4
19 mm
Supplied
by
controller
9 m
Standard Series
32 mm
V-Series
Controllers
N/A
24V dc,
115 or
230V ac
N/A
Metal Box Controllers
24V dc
DIN Module Controllers
MINI-SCREEN®
Emitters & Receivers
Page 58 4
19 & 25 mm
Supplied
by
controller
18 m
Standard Series
38 mm
Heavy-Duty Series
Controllers
N/A
24V dc,
115V ac
or
230V ac N/A
Metal Box Controllers
24V dc
DIN Module Controllers
EZ-SCREEN® Type 2
Type 2 Systems Page 78 2 30 mm 24V dc 15 m
NC = Normally Closed Relay, NO = Normally Open Relay
19More information online at bannerengineering.com
SAFETY LIGHT SCREENS
SAFETY
LIGHT SCREENS
Safety Muting Output Housing Environmental
Output Blanking Option Response Time Material Rating
2 PNP
OSSD
(Trip /Latch
Selectable)
Reduced Resolution
(floating)
2-beam
&
Fixed
Optional
Accessory
(see page 123)
9 to 56 ms
Aluminum housing
with yellow polyester
powder finish
or nickel-plated ESD
IEC IP65
11 to 56 ms
—≤ 24 ms
2 PNP
OSSD
(Trip /Latch
Selectable)
See page 108
for controller
—
Optional
Accessory
(see page 123)
13 ms
See page 108
for controller
Black aluminum housing,
tempered glass window IEC IP65
12 mm threaded barrel: Black
polycarbonate plastic housing
30 mm threaded barrel: Stainless
steel housing, glass window.
IEC IP67
—
Reduced Resolution
(floating)
1- or 2-beam
&
Fixed
—
< 38 ms
(< 48 ms for
muting)
Aluminum housing
with yellow polyester
powder finish
or
nickel-plated ESD
IEC IP65
2 NO
(Trip or Latch) Yes Welded steel box with black
polyester powder paint finish IEC IP64
2 or 4 NO
(Trip or Latch)
Optional
Accessory
(see page 123)
Gray polycarbonate IEC IP20
—
Reduced Resolution
(floating)
1- or 2-beam
&
Fixed
—
< 48 to < 72 ms
(< 58 to < 82 ms
for muting)
Aluminum housing with
black anodized or
yellow polyester painted finish
IEC IP65
2 NO
(Trip or Latch)
Yes Welded steel box with black
polyester powder paint finish IEC IP64
Optional
Accessory
(see page 123)
Gray polycarbonate IEC IP20
2 PNP
OSSD
(Trip or Latch)
—
Optional
Accessory
(see page 123)
11 to 25 ms
Aluminum housing
with yellow polyester
powder finish
IEC IP65
20 More information online at bannerengineering.com
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN®
TYPE 2
14 mm Resolution Models . . . . . . . . . . . . Page 21
30 mm Resolution Models . . . . . . . . . . . . . . . . . 22
Cascade Systems . . . . . . . . . . . . . . . . . . . . . . . . 24
14 and 30 mm Interfacing Products. . . . . . . . . . 26
14 and 30 mm Resolution Kits . . . . . . . . . . . . . . 27
Grid and Point Models . . . . . . . . . . . . . . . . . . 28
Grid and Point Interfacing Products . . . . . . . . . . 30
Grid Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Point Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
EZ-SCREEN® Systems
SAFETY LIGHT SCREENS
EZ-SCREEN
®
Safety Light Screens
• Simple, two-piece integrated system has no control box.
• High-resolution 14 and 30 mm EZ-SCREEN® point-of-operation
systems provide finger, hand and ankle detection.
• EZ-SCREEN Point and Grid systems allow one-, two-, three-
or four-beam perimeter and access guarding.
• Superior optical design and finely focused ±2.5° beam make
systems extremely easy to align and maintain.
• Status indicators and diagnostics show when alignment is
complete and if there are problems with the installation.
• Redundant microprocessor-controlled, self-checking
design exceeds control reliability requirements and is
certified per CE (Type 4/Category 4) and cULus (NIPF,
UL 61496, UL 1998).
• Unique cascading models (patent-pending) allow up to four
systems of any length and resolution to be wired together to
form a single safety device.
• Systems have ranges up to 70 m, with power and range for all
types of applications including long-range perimeter guarding.
Point of
operation.
• Finger, hand or
ankle detection
at the point of
operation.
• Use 14 or 30 mm
EZ-SCREEN.
Area.
• Mount horizontally
to eliminate safety
mats and area
scanners.
• Manually reset
Latch output when
area is clear.
Perimeter.
• Guard mulitple
sides of a
dangerous area
up to 70 m long.
• Expand guarding
with optional
corner mirrors and
mounting stands.
Long-range
single sided.
• EZ-SCREEN Grid
systems provide
2, 3 or 4 beams.
• Beam spacing
is from 300 to
584 mm.
Single point
access.
• Use with angled
mirrors to simulate
a 2-beam system.
• Use multiple units
for custom beam
patterns.
ESD applications.
• Dissipate
electrostatic
discharges.
• Ideal for
microelectronic
applications.
A complete family of machine guarding products.
QD CABLES
PAGE 176
).$)#!4/23
PAGE 187
-)22/23
PAGE
204
34!.$3
PAGE
209
,%.33()%,$3
PAGE
213
%.#,/352%3
PAGE
216
8-Pin Euro + 3- &
8-Pin Mini
BRACKETS
PAGE 190
EZ-SCREEN® Systems
21More information online at bannerengineering.com
SAFETY LIGHT SCREENS
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN
®
TYPE 2
EZ-SCREEN® Systems, 14 mm Resolution
Models* Resolution Range
Defined
Area
Housing
Length (L)
Supply
Voltage
Safety
Outputs
Response
Time
Connec-
tion**
Data
Sheet
SLSP14-150Q88†
14 mm Resolution
0.1 to 6 m
150 mm 262 mm
24V dc 2 PNP
OSSD
≤ 11 ms
8-pin
Euro QD 112852
SLSE14-150Q8
SLSR14-150Q8
SLSP14-300Q88†
300 mm 372 mm ≤ 15 msSLSE14-300Q8
SLSR14-300Q8
SLSP14-450Q88†
450 mm 522 mm ≤ 19 msSLSE14-450Q8
SLSR14-450Q8
SLSP14-600Q88†
600 mm 671 mm ≤ 23 msSLSE14-600Q8
SLSR14-600Q8
SLSP14-750Q88†
750 mm 821 mm ≤ 27 msSLSE14-750Q8
SLSR14-750Q8
SLSP14-900Q88†
900 mm 971 mm ≤ 32 ms
SLSE14-900Q8
SLSR14-900Q8
SLSP14-1050Q88†
1050 mm 1120 mm ≤ 36 ms
SLSE14-1050Q8
SLSR14-1050Q8
7-segment diagnostic display
Blocked beam zone indicators
System status and system reset
status
Integral or pigtail Euro-style QD
connection
Durable aluminum housing to
resist twisting
Metal end caps for added durability
User configurable trip or latch
outputs and Scan Code 1 or 2
Fixed or 2-beam reduced
resolution (floating) blanking
EDM input and optional TEST**
function
EZ-SCREEN® Systems
EZ-SCREEN Systems
Detailed
Dimensions
45.0 mm
L
36.0 mm
Full View of
Available Finishes
Yellow Painted
Aluminum
Nickel-Plated
ESD
Download
PDF
14 mm Resolution
* Nickel-plated emitters and receivers used for ESD safe applications are available by adding “N” in the model number (example, SLSE14-150NQ8).
** For an emitter with TEST function, replace Q8 with Q5 on emitter model numbers (example, SLSE14-150Q5) and Q88 with Q85 on pair model numbers
(example, SLSP14-150Q85). For a 300 mm Euro pigtail QD, replace “Q” with “P” in models numbers (example, SLSP14-150P88). A model with a QD requires a mating
cable (see page 176).
† A pair includes an emitter and receiver (example, SLSP14-150Q88). Emitters (example, SLSE14-150Q8) and receivers (example, SLSR14-150Q8) are also sold separately.
22 More information online at bannerengineering.com
SAFETY LIGHT SCREENS
EZ-SCREEN® Systems
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN®
TYPE 2
EZ-SCREEN® Systems, 14 mm Resolution
Models* Resolution Range
Defined
Area
Housing
Length (L)
Supply
Voltage
Safety
Outputs
Response
Time
Connec-
tion**
Data
Sheet
SLSP14-1200Q88†
14 mm Resolution
0.1 to 6 m
1200 mm 1270 mm
24V dc 2 PNP
OSSD
≤ 40 ms
8-pin
Euro QD 112852
SLSE14-1200Q8
SLSR14-1200Q8
SLSP14-1350Q88†
1350 mm 1420 mm ≤ 43 msSLSE14-1350Q8
SLSR14-1350Q8
SLSP14-1500Q88†
1500 mm 1569 mm ≤ 48 msSLSE14-1500Q8
SLSR14-1500Q8
SLSP14-1650Q88†
1650 mm 1719 mm ≤ 52 ms
SLSE14-1650Q8
SLSR14-1650Q8
SLSP14-1800Q88†
1800 mm 1869 mm ≤ 56 msSLSE14-1800Q8
SLSR14-1800Q8
EZ-SCREEN® Systems, 30 mm Resolution
Models* Resolution Range
Defined
Area
Housing
Length (L)
Supply
Voltage
Safety
Outputs
Response
Time
Connec-
tion**
Data
Sheet
SLSP30-150Q88†
30 mm Resolution
0.1 to 18 m
150 mm 262 mm
24V dc 2 PNP
OSSD
≤ 9 ms
8-pin
Euro QD 112852
SLSE30-150Q8
SLSR30-150Q8
SLSP30-300Q88†
300 mm 372 mm ≤ 11 ms
SLSE30-300Q8
SLSR30-300Q8
SLSP30-450Q88†
450 mm 522 mm ≤ 13 ms
SLSE30-450Q8
SLSR30-450Q8
SLSP30-600Q88†
600 mm 671 mm ≤ 15 ms
SLSE30-600Q8
SLSR30-600Q8
SLSP30-750Q88†
750 mm 821 mm ≤ 17 ms
SLSE30-750Q8
SLSR30-750Q8
14 mm Resolution 30 mm Resolution
* Nickel-plated emitters and receivers used for ESD safe applications are available by adding “N” in the model number (example, SLSE14-1200NQ8).
** For an emitter with TEST function, replace Q8 with Q5 on emitter model numbers (example, SLSE14-1200Q5) and Q88 with Q85 on pair model numbers
(example, SLSP14-1200Q85). For a 300 mm Euro pigtail QD, replace “Q” with “P” in models numbers (example, SLSP14-1200P88). A model with a QD requires a
mating cable (see page 176).
† A pair includes an emitter and receiver (example, SLSP14-1200Q88). Emitters (example, SLSE14-1200Q8) and receivers (example, SLSR14-1200Q8) are also sold separately.
Download
PDF
Download
PDF
(cont’d)
EZ-SCREEN® Systems
23More information online at bannerengineering.com
SAFETY LIGHT SCREENS
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN
®
TYPE 2
EZ-SCREEN® Systems, 30 mm Resolution
Models* Resolution Range
Defined
Area
Housing
Length (L)
Supply
Voltage
Safety
Outputs
Response
Time
Connec-
tion**
Data
Sheet
SLSP30-900Q88†
30 mm Resolution
0.1 to 18 m
900 mm 971 mm
24V dc 2 PNP
OSSD
≤ 19 ms
8-pin
Euro QD 112852
SLSE30-900Q8
SLSR30-900Q8
SLSP30-1050Q88†
1050 mm 1120 mm ≤ 21 msSLSE30-1050Q8
SLSR30-1050Q8
SLSP30-1200Q88†
1200 mm 1270 mm ≤ 23 msSLSE30-1200Q8
SLSR30-1200Q8
SLSP30-1350Q88†
1350 mm 1420 mm ≤ 25 ms
SLSE30-1350Q8
SLSR30-1350Q8
SLSP30-1500Q88†
1500 mm 1569 mm ≤ 27 msSLSE30-1500Q8
SLSR30-1500Q8
SLSP30-1650Q88†
165 0 mm 1719 mm ≤ 30 msSLSE30-1650Q8
SLSR30-1650Q8
SLSP30-1800Q88†
1800 mm 1869 mm ≤ 32 msSLSE30-1800Q8
SLSR30-1800Q8
30 mm Resolution
* Nickel-plated emitters and receivers used for ESD safe applications are available by adding “N” in the model number (example, SLSE30-900NQ8).
** For an emitter with TEST function, replace Q8 with Q5 on emitter model numbers (example, SLSE30-900Q5) and Q88 with Q85 on pair model numbers
(example, SLSP30-900Q85). For a 300 mm Euro pigtail QD, replace “Q” with “P” in models numbers (example, SLSP30-900P88). A model with a QD requires a mating
cable (see page 176).
† A pair includes an emitter and receiver (example, SLSP30-900Q88). Emitters (example, SLSE30-900Q8) and receivers (example, SLSR14-900Q8) are also sold separately.
Download
PDF
(cont’d)
24 More information online at bannerengineering.com
SAFETY LIGHT SCREENS
EZ-SCREEN® Systems
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN®
TYPE 2
EZ-SCREEN® Cascade Systems, 14 mm Resolution
Models* Resolution Range
Defined
Area
Housing
Length (L)
Supply
Voltage
Safety
Outputs
Response
Time**
Connec-
tion***
Data
Sheet
SLSCP14-300Q88†
14 mm Resolution
0.1 to 6 m
300 mm 372 mm
24V dc 2 PNP
OSSD
≤ 15 ms
8-pin
Euro QD 112852
SLSCE14-300Q8
SLSCR14-300Q8
SLSCP14-450Q88†
450 mm 522 mm ≤ 19 msSLSCE14-450Q8
SLSCR14-450Q8
SLSCP14-600Q88†
600 mm 671 mm ≤ 23 msSLSCE14-600Q8
SLSCR14-600Q8
SLSCP14-750Q88†
750 mm 821 mm ≤ 27 msSLSCE14-750Q8
SLSCR14-750Q8
SLSCP14-900Q88†
900 mm 971 mm ≤ 32 msSLSCE14-900Q8
SLSCR14-900Q8
SLSCP14-1050Q88†
1050 mm 1120 mm ≤ 36 msSLSCE14-1050Q8
SLSCR14-1050Q8
SLSCP14-1200Q88†
1200 mm 1270 mm ≤ 40 msSLSCE14-1200Q8
SLSCR14-1200Q8
SLSCP14-1350Q88†
1350 mm 1420 mm ≤ 43 msSLSCE14-1350Q8
SLSCR14-1350Q8
SLSCP14-1500Q88†
1500 mm 1569 mm ≤ 48 msSLSCE14-1500Q8
SLSCR14-1500Q8
SLSCP14-1650Q88†
1650 mm 1719 mm ≤ 52 msSLSCE14-1650Q8
SLSCR14-1650Q8
SLSCP14-1800Q88†
1800 mm 1869 mm ≤ 56 msSLSCE14-1800Q8
SLSCR14-1800Q8
14 mm Resolution
* Nickel-plated emitters and receivers used for ESD safe applications are available by adding “N” in the model number (example, SLSCE14-300NQ8).
** Cascading system response time: To the response time of the slowest pair, add 2 ms for each additional pair. Example: slowest pair’s response time is 15 ms, and the
system has three additional pairs (four pairs total), so the system maximum response time is 15 ms + 6 ms (3 pairs x 2 ms) = 21 ms.
*** For an emitter with TEST function, replace Q8 with Q5 on emitter model numbers (example, SLSCE14-300Q5) and Q88 with Q85 on pair model numbers
(example, SLSCP14-300Q85). For a 300 mm Euro pigtail QD, replace “Q” with “P” in models numbers (example, SLSCP14-300P88). A model with a QD requires a
mating cable (see page 176).
† A pair includes an emitter and receiver (example, SLSCP14-300Q88). Emitters (example, SLSCE14-300Q8) and receivers (example, SLSCR14-300Q8) are also sold separately.
Download
PDF
EZ-SCREEN® Systems
25More information online at bannerengineering.com
SAFETY LIGHT SCREENS
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN
®
TYPE 2
EZ-SCREEN® Cascade Systems, 30 mm Resolution
Models* Resolution Range
Defined
Area
Housing
Length (L)
Supply
Voltage
Safety
Outputs
Response
Time**
Connec-
tion***
Data
Sheet
SLSCP30-300Q88†
30 mm Resolution
0.1 to 18 m
300 mm 372 mm
24V dc 2 PNP
OSSD
≤ 11 ms
8-pin
Euro QD 112852
SLSCE30-300Q8
SLSCR30-300Q8
SLSCP30-450Q88†
450 mm 522 mm ≤ 13 msSLSCE30-450Q8
SLSCR30-450Q8
SLSCP30-600Q88†
600 mm 671 mm ≤ 15 msSLSCE30-600Q8
SLSCR30-600Q8
SLSCP30-750Q88†
750 mm 821 mm ≤ 17 msSLSCR30-750Q8
SLSCR30-750Q8
SLSCP30-900Q88†
900 mm 971 mm ≤ 19 msSLSCE30-900Q8
SLSCR30-900Q8
SLSCP30-1050Q88†
1050 mm 1120 mm ≤ 21 msSLSCE30-1050Q8
SLSCR30-1050Q8
SLSCP30-1200Q88†
1200 mm 1270 mm ≤ 23 msSLSCE30-1200Q8
SLSCR30-1200Q8
SLSCP30-1350Q88†
1350 mm 1420 mm ≤ 25 msSLSCE30-1350Q8
SLSCR30-1350Q8
SLSCP30-1500Q88†
1500 mm 1569 mm ≤ 27 msSLSCE30-1500Q8
SLSCR30-1500Q8
SLSCP30-1650Q88†
1650 mm 1719 mm ≤ 30 msSLSCE30-1650Q8
SLSCR30-1650Q8
SLSCP30-1800Q88†
1800 mm 1869 mm ≤ 32 msSLSCE30-1800Q8
SLSCR30-1800Q8
30 mm Resolution
* Nickel-plated emitters and receivers used for ESD safe applications are available by adding “N” in the model number (example, SLSCE30-300NQ8).
** Cascading system response time: To the response time of the slowest pair, add 2 ms for each additional pair. Example: slowest pair’s response time is 15 ms, and the
system has three additional pairs (four pairs total), so the system maximum response time is 15 ms + 6 ms (3 pairs x 2 ms) = 21 ms.
*** For an emitter with TEST function, replace Q8 with Q5 on emitter model numbers (example, SLSCE30-300Q5) and Q88 with Q85 on pair model numbers
(example, SLSCP30-300Q85). For a 300 mm Euro pigtail QD, replace “Q” with “P” in models numbers (example, SLSCP30-300P88). A model with a QD requires a
mating cable (see page 176).
† A pair includes an emitter and receiver (example, SLSCP30-300Q88). Emitters (example, SLSCE30-300Q8) and receivers (example, SLSCR30-300Q8) are also sold separately.
Download
PDF
26 More information online at bannerengineering.com
SAFETY LIGHT SCREENS
EZ-SCREEN® Systems
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN®
TYPE 2
EZ-SCREEN® Interfacing Products
Models Description
Product
Information
Data
Sheet
Interface Modules
IM-T-9A (3 NO)
• Interface modules provide two or three
normally open force-guided relay outputs
rated at 6 A.
• EZ-SCREEN monitors these interface modules
when they are connected to the EZ-SCREEN
External Device Monitoring (EDM) inputs.
• Convenient plug-in terminal blocks on a
22.5 mm DIN-rail mountable housing are
included.
Page 132 62822
IM-T-11A (2 NO/1 NC)
Muting Modules
MM-TA-12B • The Muting Module temporarily inhibits a
safety light screen so materials can safely
pass through the screen without stopping
the machinery.
• The module uses redundant microcontroller-
based logic.
Page 123
63517
MMD-TA-12B
116390
MMD-TA-11B
Receiver
AC Interface Boxes
EZAC-R9-QE8
• Versatile power supplies allow EZ-SCREEN
systems to connect to AC power sources.
• Models are available to accommodate
receivers only, emitters only, or both.
• Receiver models include 8 amp safety relay
output.
Page 184 120321
EZAC-R11-QE8
EZAC-R15A-QE8-QS83
EZAC-R8N-QE8-QS53
EZAC-R10N-QE8-QS53
Emitter
AC Interface Boxes
EZAC-E-QE8
EZAC-E-QE5
EZAC-E-QE8-QS3
EZAC-E-QE5-QS5
Contactors
Mechanically
Linked Contactors • Pairs of contactors create safety stop circuits
with two normally open contacts in series.
• EZ-SCREEN can monitor the circuit because of
the contacts’ force-guided mechanically linked
design.
• Contactors add 10 or 16 amp current carrying
capability to any safety system.
• Auxiliary contacts add 3 or 4 normally open
contacts.
• Suppressors extend the life of an actuating
device that uses a contactor.
• Modular design simplifies assembly and
installation.
Page 186 111881
11-BG00-31-D-024
11-BF16C01-024
Aux. Contacts
11-BGX10-40
11-G484-30
Suppressors
11-BGX77-048
11-G318-48
Download
PDF
EZ-SCREEN® Systems
27More information online at bannerengineering.com
SAFETY LIGHT SCREENS
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN
®
TYPE 2
You can purchase a kit that contains an emitter and receiver of equal length and resolution; brackets;
and optional interfacing solution and quick-disconnect cables. Detailed information about individual kit
components is as follows.
• Emitter and Receivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 21
• Interfacing Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
• Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
• Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
A partial listing of kits is listed below; see Kit Model Key to order other variations.
EZ-SCREEN® 14 & 30 mm Resolution Kits
Kit Model Number
SLSK14-600Q88-1RE25 •
No
600 mm
14 mm 6 m
24V dc 2 OSSD
Trip /
Latch
Select-
able
Integral
Euro QD
without
Test
IM-T-9A,
1 each
8 m,
2 each
SLSK30-600Q88-1RE25 30 mm 18 m
SLSK14-600NQ88-1RE25 •14 mm 6 m
SLSK30-600NQ88-1RE25 30 mm 18 m
SLSCK14-600Q88-1RE25 •
Yes*
14 mm 6 m
SLSCK30-600Q88-1RE25 30 mm 18 m
SLSCK14-600NQ88-1RE25 •14 mm 6 m
SLSCK30-600NQ88-1RE25 30 mm 18 m
* For cascading systems, order one kit; up to three additional emitter/receiver pairs; and two double-ended cables per additional emitter/receiver pair. Opposed pairs
must be the same length and resolution (see page 24).
Sensor
Housing
Cascading
Protected
Height
Resolution
Range
Supply
Voltage
No. of
Outputs
Output
Options
Emitter &
Receiver
Connection
Interfacing
Options
QD Cabling
Yellow
Nickel-
Plated
Model Style
SLS = Safety Light Screen
SLSC = Cascading Safety
Light Screen
Model Style
14SLS K 1 RE25
Kit Resolution Protected
Height QD Options Interfacing
Options QD Cabling
Length Options
SLS Resolution
14 = 14 mm
30 = 30 mm
Kit
K = Kit
Protected Height
150 mm
300 mm
450 mm
600 mm
750 mm
900 mm
1050 mm
1200 mm
1350 mm
1500 mm
1650 mm
1800 mm
NOTE: Not all combinations are possible. Contact Banner Engineering Corp. for additional information and/or verification of valid kit model numbers.
Receiver & Emitter QD Options
Q85 = Receiver with integral 8-pin Euro-style QD
Emitter with integral 5-pin Euro-style QD with Test
Q88 = Receiver with integral 8-pin Euro-style QD
Emitter with integral 8-pin Euro-style QD
P85 = Receiver with integral 8-pin Euro-style pigtail QD
Emitter with integral 5-pin Euro-style pigtail QD with Test
P88 = Receiver with integral 8-pin Euro-style pigtail QD
Emitter with integral 8-pin Euro-style pigtail QD
Interfacing Options
1 = IM-T-9A Interface Module, 1 each
2 = IM-T-11A Interface Module, 1 each
3 = 11-BG00-31-D-024 Contactors (10A), 2 each
4 = 11-BF16C01-024 Contactors (16A), 2 each
5 = EZAC-R9-QE8 = AC Interface Box (3 NO), 1 each
6 = EZAC-R11-QE8 = AC Interface Box (2 NO/1 NC), 1 each
QD Cabling Length Options
RE15 = 5 m, 2 each
RE25 = 8 m, 2 each
R15E25 = 5 m (Receiver) & 8 m (Emitter)
R25E15 = 8 m (Receiver) & 5 m (Emitter)
RE50 = 15 m, 2 each
R15E50 = 5 m (Receiver) & 15 m (Emitter)
R50E15 = 15 m (Receiver) & 5 m (Emitter)
R25E50 = 8 m (Receiver) & 15 m (Emitter)
R50E25 = 15 m (Receiver) & 8 m (Emitter)
RE75 = 23 m, 2 each
RE100 = 30 m, 2 each
600
Finish
Sensor Finish
Blank = Yellow powder coat
N = Nickel plated ESD
Q88
Kit Model Key
28 More information online at bannerengineering.com
SAFETY LIGHT SCREENS
EZ-SCREEN® Systems
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN®
TYPE 2
EZ-SCREEN® Grid & Point Systems
Models
Beam
Spacing Range
Protected
Height
Housing
Length (L)
Supply
Voltage
Safety
Outputs
Response
Time Connection*
Data
Sheet
SGP4-300Q83†
300 mm
0.8
to
20 m
900 mm 1084 mm
24V dc 2 PNP
OSSD ≤ 24 ms
Emitter, 3-pin Mini QD
Receiver, 8-pin Mini QD
68410
SGE4-300Q3 3-pin Mini QD
SGR4-300Q8 8-pin Mini QD
SGXLP4-300Q83†
15
to
70 m
Emitter, 3-pin Mini QD
Receiver, 8-pin Mini QD
SGXLE4-300Q3 3-pin Mini QD
SGR4-300Q8 8-pin Mini QD
SGP3-400Q83†
400 mm
0.8
to
20 m
800 mm 984 mm
Emitter, 3-pin Mini QD
Receiver, 8-pin Mini QD
SGE3-400Q3 3-pin Mini QD
SGR3-400Q8 8-pin Mini QD
SGXLP3-400Q83†
15
to
70 m
Emitter, 3-pin Mini QD
Receiver, 8-pin Mini QD
SGXLE3-400Q3 3-pin Mini QD
SGR3-400Q8 8-pin Mini QD
One to four beam models
for access or perimeter
guarding applications
Range from 0.8 to 20 m or
15 to 70 m, depending on
model
7-segment diagnostic
display
Bi-color status indicator
IEC 61496-1 Type 4
User configurable trip or
latch outputs and Scan
Code 1 or 2
Configuration access port
Models with integral Mini
and Euro QD, or wiring
terminal chamber
QD cables ordered separately (see
page 179)
EZ-SCREEN® Grid & Point Systems
EZ-SCREEN Grid
Detailed
Dimensions
4-Beam Grid 3-Beam Grid
* For emitters and receivers with a wiring terminal chamber, remove the Q3, Q8 or Q83 from the model number (example, SGE4-300). For an emitter with TEST function,
replace Q3 with Q5 on emitter model numbers (example, SGE4-300Q5) and Q83 with Q85 on pair model numbers (example, SGP4-300Q85). For emitters and receivers
with an 8-pin integral Euro QD, replace Q3 with Q8E on model numbers (example, SGE4-300Q8E) and Q83 with Q88E on pair model numbers (example, SGP4-300Q88E).
A model with a QD requires a mating cable (see page 178).
† A pair includes an emitter and receiver (example, SGP4-300Q83). Emitters (example, SGE4-300Q3) and receivers (example, SGR4-300Q8) are also sold separately.
EZ-SCREEN Point
Full View
EZ-SCREEN
Grid
EZ-SCREEN
Point
55.0 mm
L
52.0 mm
Download
PDF
EZ-SCREEN® Systems
29More information online at bannerengineering.com
SAFETY LIGHT SCREENS
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN
®
TYPE 2
EZ-SCREEN® Grid & Point Systems
Models
Beam
Spacing Range
Protected
Height
Housing
Length (L)
Supply
Voltage
Safety
Outputs
Response
Time Connection*
Data
Sheet
SGP3-533Q83†
533 mm
0.8
to
20 m
1066 mm 1251 mm
24V dc 2 PNP
OSSD ≤ 24 ms
Emitter, 3-pin Mini QD
Receiver, 8-pin Mini QD
68410
SGE3-533Q3 3-pin Mini QD
SGR3-533Q8 8-pin Mini QD
SGXLP3-533Q83†
15
to
70 m
Emitter, 3-pin Mini QD
Receiver, 8-pin Mini QD
SGXLE3-533Q3 3-pin Mini QD
SGR3-533Q8 8-pin Mini QD
SGP2-500Q83†
500 mm
0.8
to
20 m
500 mm 684 mm
Emitter, 3-pin Mini QD
Receiver, 8-pin Mini QD
SGE2-500Q3 3-pin Mini QD
SGR2-500Q8 8-pin Mini QD
SGXLP2-500Q83†
15
to
70 m
Emitter, 3-pin Mini QD
Receiver, 8-pin Mini QD
SGXLE2-500Q3 3-pin Mini QD
SGR2-500Q8 8-pin Mini QD
SGP2-584Q83†
584 mm
0.8
to
20 m
584 mm 768 mm
Emitter, 3-pin Mini QD
Receiver, 8-pin Mini QD
SGE2-584Q3 3-pin Mini QD
SGR2-584Q8 8-pin Mini QD
SGXLP2-584Q83†
15
to
70 m
Emitter, 3-pin Mini QD
Receiver, 8-pin Mini QD
SGXLE2-584Q3 3-pin Mini QD
SGR2-584Q8 8-pin Mini QD
SPP1Q83†
1-BEAM
0.8
to
20 m
N/A 149 mm
Emitter, 3-pin Mini QD
Receiver, 8-pin Mini QD
68413
SPE1Q3 3-pin Mini QD
SPR1Q8 8-pin Mini QD
SPXLP1Q83†
15
to
70 m
Emitter, 3-pin Mini QD
Receiver, 8-pin Mini QD
SPXLE1Q3 3-pin Mini QD
SPR1Q8 8-pin Mini QD
3-Beam Grid 2-Beam Grid 1-Beam Point
** For emitters and receivers with a wiring terminal chamber, remove the Q3, Q8 or Q83 from the model number (example, SGE3-533). For an emitter with TEST function,
replace Q3 with Q5 on emitter model numbers (example, SGE3-533Q5) and Q83 with Q85 on pair model numbers (example, SGP3-533Q85). For emitters and receivers
with an 8-pin integral Euro QD, replace Q3 with Q8E on model numbers (example, SGE3-533Q8E) and Q83 with Q88E on pair model numbers (example, SGP3-533Q88E).
A model with a QD requires a mating cable (see page 178).
† A pair includes an emitter and receiver (example, SGP3-533Q83). Emitters (example, SGE3-533Q3) and receivers (example, SGR3-533Q8) are also sold separately.
Download
PDF
(cont’d)
30 More information online at bannerengineering.com
SAFETY LIGHT SCREENS
EZ-SCREEN® Systems
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN®
TYPE 2
EZ-SCREEN® Grid & Point Interfacing Products
Models Description Product
Data
Sheet
Interface Modules
IM-T-9A (3 NO)
• Interface modules provide two or three
normally open force-guided relay outputs rated
at 6 A.
• EZ-SCREEN monitors these interface modules
when they are connected to the EZ-SCREEN
External Device Monitoring (EDM) inputs.
• Convenient plug-in terminal blocks on a 22.5 mm
DIN-rail mountable housing are included.
Page 132 62822
IM-T-11A (2 NO/1 NC)
Muting Modules
MM-TA-12B • The Muting Module temporarily inhibits a
safety light screen so materials can safely
pass through the screen without stopping the
machinery.
• The module uses redundant microcontroller-
based logic.
Page 123
63517
MMD-TA-12B
116390
MMD-TA-11B
Receiver
AC Interface Boxes
EZAC-R9-QE8
• Versatile power supplies allow EZ-SCREEN
systems to connect to AC power sources.
• Models are available to accommodate receivers
only, emitters only, or both.
• Receiver models include 8 amp safety relay
output.
Page 184 120321
EZAC-R11-QE8
EZAC-R15A-QE8-QS83
EZAC-R8N-QE8-QS53
EZAC-R10N-QE8-QS53
Emitter
AC Interface Boxes
EZAC-E-QE8
EZAC-E-QE5
EZAC-E-QE8-QS3
EZAC-E-QE5-QS5
Contactors
Mechanically
Linked Contactors • Pairs of contactors create safety stop circuits
with two normally open contacts in series.
• EZ-SCREEN can monitor the circuit because of
the contacts’ force-guided mechanically linked
design.
• Contactors add 10 or 16 amp current carrying
capability to any safety system.
• Auxiliary contacts add 3 or 4 normally open
contacts.
• Suppressors extend the life of an actuating
device that uses a contactor.
• Modular design simplifies assembly and
installation.
Page 186 111881
11-BG00-31-D-024
11-BF16C01-024
Aux. Contacts
11-BGX10-40
11-G484-30
Suppressors
11-BGX77-048
11-G318-48
Download
PDF
EZ-SCREEN® Systems
31More information online at bannerengineering.com
SAFETY LIGHT SCREENS
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN
®
TYPE 2
Kit Model Number
Beams
Beam
Spacing
Protected
Height
Range
Supply
Voltage
No. of
Outputs
Output
Options
Emitter &
Receiver
Connection
Interfacing
Options
QD Cabling
SGK4-300Q83-1RE25 4 300 mm 900 mm 20 m
24V dc 2 OSSD Trip/ Latch
Selectable
Integral
Mini QD
without Test
IM-T-9A,
1 each
8 m,
2 each
SGXLK4-300Q83-1RE25 70 m
SGK3-400Q83-1RE25
3
400 mm 800 mm 20 m
SGXLK3-400Q83-1RE25 70 m
SGK3-533Q83-1RE25 533 mm 1066 mm 20 m
SGXLK3-533Q83-1RE25 70 m
SGK2-500Q83-1RE25
2
500 mm 500 mm 20 m
SGXLK2-500Q83-1RE25 70 m
SGK2-584Q83-1RE25 584 mm 584 mm 20 m
SGXLK2-584Q83-1RE25 70 m
Model Style
SG = Safety Grid
SGXL = Safety Grid Long
Range
Model Style Kit Beam
Spacing QD Options Interfacing
Options QD Cabling
Length Options
No. of Beams
2 = two beams
3 = three beams
4 = four beams
Kit
K = Kit
Beam Spacing
300 mm
400 mm
500 mm
533 mm
584 mm
Receiver & Emitter QD Options
Blank = Receiver and emitter with wiring terminal chamber
Q85 = Receiver with integral 8-pin Mini-style QD
Emitter with integral 5-pin Mini-style QD with Test
Q83 = Receiver with integral 8-pin Mini-style QD
Emitter with integral 3-pin Mini-style QD
Q88E = Receiver and emitter with integral 8-pin Euro-style QD
Interfacing Options
1 = IM-T-9A Interface Module, 1 each
2 = IM-T-11A Interface Module, 1 each
3 = 11-BG00-31-D-024 Contactors (10A), 2 each
4 = 11-BF16C01-024 Contactors (16A), 2 each
QD Cabling Length Options
RE15 = 5 m, 2 each
RE25 = 8 m, 2 each
R15E25 = 5 m (Receiver) & 8 m (Emitter)
R25E15 = 8 m (Receiver) & 5 m (Emitter)
RE50 = 15 m, 2 each
R15E50 = 5 m (Receiver) & 15 m (Emitter)
R50E15 = 15 m (Receiver) & 5 m (Emitter)
R25E50 = 8 m (Receiver) & 15 m (Emitter)
R50E25 = 15 m (Receiver) & 8 m (Emitter)
RE75 = 23 m, 2 each
RE100 = 30 m, 2 each
EZ-SCREEN® Grid Kits
Kit Model Key
No. of Beams
SG K 1 RE25300 Q834
NOTE: Not all combinations are possible. Contact Banner Engineering Corp. for additional information and/or verification of valid kit model numbers.
You can purchase a kit that contains an emitter and receiver of equal length and beam spacing; brackets;
and optional interfacing solution and quick-disconnect cables. Detailed information about individual kit
components is as follows.
• Emitter and Receivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 28
• Interfacing Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
• Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .178 & 179
• Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
A partial listing of kits is listed below; see Kit Model Key to order other variations.
32 More information online at bannerengineering.com
SAFETY LIGHT SCREENS
EZ-SCREEN® Systems
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN®
TYPE 2
EZ-SCREEN® Point Kits
SPK1-Q83-1RE25
1N/A
20 m
24V dc 2 OSSD Trip / Latch
Selectable
Integral
Mini QD
without Test
IM-T-9A,
1 each
8 m,
2 each
SPXLK1-Q83-1RE25 70 m
Kit Model Number
Beams
Beam
Spacing
Range
Supply
Voltage
No. of
Outputs
Output
Options
Emitter &
Receiver
Connection
Interfacing
Options
QD Cabling
Model Style
SP = Safety Point
SPXL = Safety Point
Long Range
Model Style Kit QD Options Interfacing
Options QD Cabling
Length Options
No. of Beams
1 = one beam
Kit
K = Kit
Interfacing Options
1 = IM-T-9A Interface Module, 1 each
2 = IM-T-11A Interface Module, 1 each
3 = 11-BG00-31-D-024 Contactors (10A), 2 each
4 = 11-BF16C01-024 Contactors (16A), 2 each
QD Cabling Length Options
RE15 = 5 m, 2 each
RE25 = 8 m, 2 each
R15E25 = 5 m (Receiver) & 8 m (Emitter)
R25E15 = 8 m (Receiver) & 5 m (Emitter)
RE50 = 15 m, 2 each
R15E50 = 5 m (Receiver) & 15 m (Emitter)
R50E15 = 15 m (Receiver) & 5 m (Emitter)
R25E50 = 8 m (Receiver) & 15 m (Emitter)
R50E25 = 15 m (Receiver) & 8 m (Emitter)
RE75 = 23 m, 2 each
RE100 = 30 m, 2 each
Kit Model Key
No. of Beams
SP K 1 RE25Q831
You can purchase a kit that contains an emitter and receiver of equal length; brackets; and optional
interfacing solution and quick-disconnect cables. Detailed information about individual kit components is
as follows.
• Emitter and Receivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 28
• Interfacing Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
• Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .178 & 179
• Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
A partial listing of kits is listed below; see Kit Model Key to order other variations.
NOTE: Not all combinations are possible. Contact Banner Engineering Corp. for additional information and/or verification of valid kit model numbers.
Receiver & Emitter QD Options
Blank = Receiver and emitter with wiring terminal chamber
Q85 = Receiver with integral 8-pin Mini-style QD
Emitter with integral 5-pin Mini-style QD with Test
Q83 = Receiver with integral 8-pin Mini-style QD
Emitter with integral 3-pin Mini-style QD
Q88E = Receiver and emitter with integral 8-pin Euro-style QD
EZ-SCREEN® Systems
33More information online at bannerengineering.com
SAFETY LIGHT SCREENS
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN
®
TYPE 2
EZ-SCREEN® 14 & 30 mm Resolution Specifications
Supply Voltage at the Device* 24V dc ±15% (SELV), ± 10% max. ripple
Supply Current Emitter: 100 mA max.
Receiver: 275 mA max., exclusive of OSSD1 and OSSD2 loads (up to an additional 0.5A each)
Response Time 9 to 56 millesconds
Cascade Safety Stop Interface (CSSI): 40 milliseconds max.
Remote Test Input
(Optional – available only on
model SLSE..-..Q5 emitters)
Test Mode is activated either by applying a low signal (less than 3V dc) to emitter TEST #1 terminal for a
minimum of 50 milliseconds, or by opening a switch connected between TEST #1 and TEST #2 for a minimum
of 50 milliseconds. Beam scanning stops to simulate a blocked condition. A high signal at TEST #1 deactivates
Test Mode. (See p/n 112852 for more information.)
High signal: 10 to 30V dc
Low signal: 0 to 3V dc
Input current: 35 mA inrush, 10 mA max.
Wavelength of Emitter Elements Infrared LEDs, 950 nm at peak emission
EDM Input +24V dc signals from external device contacts can be monitored (one-channel, two-channel or no monitoring)
via EDM1 and EDM2 terminals in the receiver. Monitored devices must respond within 200 milliseconds of an
output change.
High signal: 10 to 30V dc at 30 mA typical
Low signal: 0 to 3V dc
Dropout time: 200 milliseconds max.
Reset Input The Reset input must be high for 0.25 to 2 seconds and then low to reset the receiver.
High signal: 10 to 30V dc at 30 mA typical
Low signal: 0 to 3V dc
Closed switch time: 0.25 to 2 seconds
Safety Outputs Two redundant solid-state 24V dc, 0.5 A max. sourcing OSSD (Output Signal Switching Device) safety outputs.
(Use optional interface modules for ac or larger dc loads.)
Capable of the Banner “Safety Handshake”.
ON-State voltage: ≥ Vin-1.5V dc
OFF-State voltage: 1.2V dc max. (0-1.2V dc)
Max. load capacitance: 1.0 µF
Max. load inductance: 10 H
Leakage current: 0.50 mA maximum
Cable resistance: 10 Ω maximum
OSSD test pulse width: 100 to 300 microseconds
OSSD test pulse period: 5 to 27 milliseconds (varies with number of beams)
Switching current: 0-0.5 A
Controls and Adjustments Emitter:
Scan Code selection: 2-position switch (code 1 or 2). Factory default position is code 1.
Receiver:
Scan Code selection: 2-position switch (code 1 or 2). Factory default position is code 1.
Trip/Latch Output selection: Redundant switches. Factory default position is T (Trip).
EDM/MPCE monitor selection: 2-position switch selects between 1- or 2-channel monitoring.
Factory default position is 2.
Reduced Resolution (2-beam Floating Blanking): Redundant switches to enable. Factory default is OFF.
Short Circuit Protection All inputs and outputs are protected from short circuits to +24V dc or dc common*
Electrical Safety Class
(IEC 61140: 1997)
III
Safety Rating Type 4 per IEC 61496-1, -2; Category 4 per ISO 13849-1 (EN 954-1)
Operating Range 14 mm models: 0.1 m to 6 m
30 mm models: 0.1 m to 18 m
Range decreases with use of mirrors and/or lens shields:
Lens shields – approximately 10% less range per shield.
Glass-surface mirrors – approximately 8% less range per mirror.
See Accessory section for more information on a specific mirror, page 204.
Ambient Light Immunity > 10,000 lux at 5° angle of incidence
Effective Aperture Angle (EAA) Meets Type 4 requirements per IEC 61496-2, ± 2.5° @ 3 m
*The external voltage supply must be capable of buffering brief mains interruptions of 20 milliseconds, as specified in IEC/EN 60204-1.
34 More information online at bannerengineering.com
SAFETY LIGHT SCREENS
EZ-SCREEN® Systems
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN®
TYPE 2
EZ-SCREEN® 14 & 30 mm Resolution Specifications
Enclosure Materials: Extruded aluminum housing with yellow polyester powder or nickel-plated finish and well-sealed,
rugged die-cast zinc end caps, acrylic lens cover, copolyester access cover
Rating: IEC IP65
Operating Conditions Temperature: 0° to +55° C Relative humidity: 95% (non-condensing)
Status Indicators Emitter:
One Bi-color (Red/Green) Status Indicator – indicates operating mode, Lockout or power OFF condition
7-segment Diagnostic Indicator (1 digit) – indicates proper operation, scan code or error code
Receiver:
Yellow Reset Indicator – indicates whether system is ready for operation or requires a reset
Bi-Color (Red/Green) Status Indicator – indicates general system and output status
Bi-Color (Red/Green) Zone Status Indicators – indicates condition (clear or blocked beam) of a defined group
of beams
7-Segment Diagnostic Indicator (3-digit) – indicates proper operation, scan code or error code, total number
of blocked beams
Mounting Hardware Emitter and receiver each are supplied with a pair of swivel end-mounting brackets. Models longer than
900 mm also include a swivel center-mount bracket. Mounting brackets are 8-gauge cold-rolled steel, black
zinc finish.
Shock and Vibration EZ-SCREEN systems have passed vibration and shock tests according to IEC 61496-1. This includes vibration
(10 cycles) of 10-55 Hz at 0.35 mm single amplitude (0.70 mm peak-to-peak) and shock of 10 g for
16 milliseconds (6,000 cycles).
Certifications For a list of certifications see page 236.
Wiring Diagrams WD001, WD002, WD003, WD004, WD009, WD010, WD011, WD012, WD013, WD014, WD015, WD016
(pp. 246-254)
EZ-SCREEN® Grid & Point Specifications
Supply Voltage (V in) 24V dc ±15%, 10% max. ripple
Supply Current Emitter: 150 mA max.
Receiver: 500 mA max., exclusive of OSSD1 and OSSD2 loads (up to an additional 0.5A each)
Short Circuit Protection All inputs and outputs are protected from short circuits to +24V dc or dc common
(except Emitter AUX power connections)
Response Time 24 milliseconds or less from interruption of light grid beam to safety outputs going to OFF-state
Safety Rating Type 4 per IEC 61496-1, -2; Category 4 per ISO 13849-1 (EN 954-1)
EDM Input +24V dc signals from external device contacts can be monitored (single-channel, dual-channel or no
monitoring) via EDM1 and EDM2 terminals in the receiver. Monitored devices must respond within
200 milliseconds of an output change.
Reset Input The Reset input must be high (10 to 30V dc at 30 mA) for 0.25 to 2 seconds and then low (less than 3V dc) to
reset the receiver.
Remote Test Input Test mode is activated either by applying a low signal (less than 3V dc) to emitter TEST1 terminal for a
minimum of 50 milliseconds, or by opening a switch connected between TEST1 and TEST2 terminals for a
minimum of 50 milliseconds. Beam scanning stops to simulate a blocked condition. A high signal
(10 to 30V dc, 35 mA inrush, 10 mA max.) at TEST1 terminal deactivates Test mode and allows the emitter to
operate normally. TEST1 and TEST2 are factory jumpered.
Safety Outputs Two diverse-redundant solid-state 24V dc, 0.5 A max. sourcing OSSD (Output Signal Switching Device) safety
outputs. (Use optional interface modules for ac or larger dc loads.)
ON-State voltage: ≥Vin-1.5V dc
OFF-State voltage: 1.2V dc max.
Max. load resistance: 1000 ohm
Max. load capacitance: 0.1 µF
Controls and Adjustments Emitter:
Scan code selection: 2-position switch (code 1 or 2). Factory default position is 1.
Receiver:
Scan code selection: 2-position switch (code 1 or 2). Factory default position is 1.
Trip/latch output selection: redundant switches. Factory default position is L (latch)
EDM/MPCE monitor selection: redundant switches select between 1- or 2-channel monitoring. Factory default
position is 2.
EZ-SCREEN® 14 & 30 mm Resolution Specifications (cont’d)
EZ-SCREEN® Systems
35More information online at bannerengineering.com
SAFETY LIGHT SCREENS
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN
®
TYPE 2
EZ-SCREEN® Grid & Point Specifications
Emitter/Receiver Operating
Range
Short-range models: 0.8 m to 20 m
Long-range models: 15 m to 70 m
Range decreases with use of mirrors and/or lens shields.
Beam Spacing Model SG...4-300: 300 mm
Model SG...3-400: 400 mm
Model SG...2-500: 500 mm
Model SG...3-533: 533.4 mm
Model SG...2-584: 584.2 mm
Beam Diameter 25 mm
Ambient Light Immunity > 10,000 lux at 5° angle of incidence
Strobe Light Immunity Totally immune to one Federal Signal Corp. “Fireball” model FB2PST strobe
Emitter Elements Infrared LEDs, 880 nm at peak emission
Effective Aperture Angle (EAA) Meets Type 4 requirements per IEC 61496-2
Short-range models: ± 2.5° @ 3 m Long-range models: ± 2.5° @ 15 m
Enclosure Materials: Extruded aluminum housings with yellow polyester powder finish and well-sealed, rugged molded
PBT end caps, acrylic lens cover
Rating: NEMA 4, 13; IEC IP65
Operating Conditions Temperature: 0° to +50° C Relative humidity: 95% (non-condensing)
Shock and Vibration EZ-SCREEN systems have passed vibration and shock tests according to IEC 61496-1 and -2. This includes
vibration (10 cycles) of 10-55 Hz at 0.35 mm single amplitude (0.70 mm peak-to-peak) and shock of 10 g for
16 milliseconds (6,000 cycles).
Status Indicators 7-Segment Diagnostic Indicators, Both Emitter and Receiver
Dash (–) = System is OK
Error Codes = See product manuals (p/n 68410 or 68413) for code definitions and
recommended action
Scan code setting = Appears during power-up or after scan code is changed.
(C1 or C2) (Temporary indication; normal display resumes within a few seconds.)
Emitter: One bi-color (red/green) Status indicator
Green steady = RUN mode
Green single flashing = TEST mode
Red single flashing = Lockout
OFF = No power to sensor
Receiver: Two System Status indicators, plus one bi-color (red/green) Beam Status indicator for each beam
Yellow Reset Indicator
ON steady = RUN mode
Double flashing = Waiting for manual reset after power-up
Single flashing = Waiting for manual latch reset
OFF = No power to sensor or system is not ready for operation
Bi-Color (Red/Green) Status Indicator
Green steady = Outputs ON
Red steady = RUN mode, outputs OFF
Red single flashing = Lockout
OFF = No power to sensor or system is not ready for operation
Bi-Color (Red/Green) Beam Status Indicators
Green steady = Clear beam, strong signal
Green flickering = Clear beam, weak signal
Red steady = Beam blocked
OFF = No power to sensor or no scanning
Mounting Hardware Emitter and receiver each are supplied with a pair of swivel end mounting brackets. Mounting brackets are
8-gauge cold-rolled steel, black zinc finish.
Cables and Connections Cables are user-supplied. Wiring terminals accommodate one 22 to 16 ga. wire or two wires up to 18 ga.;
Pg13.5 wiring chamber access port capacity varies, depending on cable gland or strain relief fitting used.
Supplied cable gland is for a cable diameter of 6 to 12 mm.
Certifications For a list of certifications see page 236.
Wiring Diagrams WD005, WD006, WD007, WD008, WD009, WD010, WD011, WD012, WD013, WD014, WD015, WD016
(pp. 248-254)
EZ-SCREEN® Grid & Point Specifications (cont’d)
36 More information online at bannerengineering.com
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN®
TYPE 2
PICO-GUARD™ Grid & Point Systems
SAFETY LIGHT SCREENS
Grid Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 37
12 mm Point Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
30 mm Point Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
PICO-GUARD
™
Grids & Points
• Fiber optic elements are for use with PICO-GUARD
Controllers and fiber optic cables in personnel safety
and equipment-protection applications.
• Choices include compact 12 or 30 mm non-contact fiber
optic Point elements, or Grid systems for perimeter and
access guarding.
• Each fiber optic channel uses one Grid or Point pair
(up to 4 pairs per controller).
• Grid system features rugged anodized aluminum
construction, with 2, 3 or 4 beams and beam spacing
from 300 to 584 mm.
• Each Point or Grid element can function as emitter or
receiver, depending on installation.
• 12 mm Point has impact-resistant polycarbonate
plastic construction.
• 30 mm Point has robust 304 stainless steel housing
with tempered glass lens window.
• Models are available for use with three types of integral
plastic optical fiber, in four lengths.
• Environmental rating is IEC IP65 for Grids and IP67
for Points.
• Grids and Points meet Type 4 per IEC 61496-2 and Safety
Category 4 per ISO 13849-1 applications when used with
a PICO-GUARD controller.
• Multiple mounting bracket options allow easy installation.
• Grid and Points are ATEX and FM approved for use in
explosive environments when used with a PICO-GUARD
controller.
BRACKETS
PAGE 190
-)22/23
PAGE
204
34!.$3
PAGE
209
#!",%',!.$3
PAGE 189
EZ-SCREEN® Systems
37More information online at bannerengineering.com
PICO-GUARD™ Grid & Point Systems
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN
®
TYPE 2
SAFETY LIGHT SCREENS
Two-, three- or four-beam models
Polished-end 7 mm PVC-coated
integral fiber cable
IEC IP65 rated
Robust black anodized housing
with field replaceable window
MEK-resistant housing for paint
booth applications
Optional MEK-resistant conduit
and cable gland (see page 189)
Interchangeable as emitter or
receiver with PICO-GUARD
controller
A complete system requires a
controller (see page 108)
PICO-GUARD™ Grid Systems
PICO-GUARD Grid
Detailed
Dimensions
PICO-GUARD™ Grid Systems
Model*
Beam
Spacing
Protected
Height
Housing
Length (L)
Fiber
Description**
Fiber
Length
Maximum
Range***
Data
Sheet
SFG4-300C8
300 mm
900 mm 1084 mm
Integral
Polished-End,
PVC Coated Fibers
7 mm diameter
2.4 m 31 m
69762
SFG4-300C15 4.5 m 27 m
SFG4-300C25 7.5 m 23 m
SFG4-300C50 15 m 15 m
SFG4-300C100 30 m 7.0 m
SFG3-400C8
400 mm
800 mm 984 mm
2.4 m 31 m
SFG3-400C15 4.5 m 27 m
SFG3-400C25 7.5 m 23 m
SFG3-400C50 15 m 15 m
SFG3-400C100 30 m 7.0 m
SFG3-533C8
533 mm
1066 mm 1251 mm
2.4 m 31 m
SFG3-533C15 4.5 m 27 m
SFG3-533C25 7.5 m 23 m
SFG3-533C50 15 m 15 m
SFG3-533C100 30 m 7.0 m
4-Beam Grid 3-Beam Grid
* Order any two Grid optical elements with the same housing length.
** MEK-resistant conduit is available to protect fiber (see page 189).
*** Maximum range is based on using an emitter and receiver with the same length fiber. Using an emitter and receiver with different length fibers may decrease or increase
range. Using corner mirrors reduces range. See specifications on page 41 for detailed range information.
55.0 mm
L
52.0 mm
Full View
Black Anodized
Aluminum
Download
PDF
38 More information online at bannerengineering.com
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN®
TYPE 2
PICO-GUARD™ Grid & Point Systems
SAFETY LIGHT SCREENS
PICO-GUARD™ Grid Systems
Model*
Beam
Spacing
Protected
Height
Housing
Length (L)
Fiber
Description**
Fiber
Length
Maximum
Range***
Data
Sheet
SFG2-500C8
500 mm
500 mm 684 mm
Integral
Polished-End,
PVC Coated Fibers
7 mm diameter
2.4 m 31 m
69762
SFG2-500C15 4.5 m 27 m
SFG2-500C25 7.5 m 23 m
SFG2-500C50 15 m 15 m
SFG2-500C100 30 m 7.0 m
SFG2-584C8
584 mm
584 mm 768 mm
2.4 m 31 m
SFG2-584C15 4.5 m 27 m
SFG2-584C25 7.5 m 23 m
SFG2-584C50 15 m 15 m
SFG2-584C100 30 m 7.0 m
2-Beam Grid
* Order any two Grid optical elements with the same housing length.
** MEK-resistant conduit is available to protect fiber (see page 189).
*** Maximum range is based on using an emitter and receiver with the same length fiber. Using an emitter and receiver with different length fibers may decrease or increase
range. Using corner mirrors reduces range. See specifications on page 41 for detailed range information.
12 or 30 mm threaded barrel fiber
optic interchangeable as emitter
or receiver with PICO-GUARD
controller
Multiple Points create customized
grid system
Polished-end coated integral fiber
Moisture and dirt
resistant
304 stainless
steel (30 mm) or
impact-resistant
polycarbonate
(12 mm) housing
Type 4 effective aperture angle
(EAA)
IEC IP67 rated
A complete system requires a
controller (see page 108)
PICO-GUARD™ Point Systems
Detailed
Dimensions
PICO-GUARD Point
(30 mm Barrel)
PICO-GUARD Point
(12 mm Barrel)
77.7 mm
ø 30.0 mm
46.4 mm
ø 12.0 mm
Download
PDF
(cont’d)
EZ-SCREEN® Systems
39More information online at bannerengineering.com
PICO-GUARD™ Grid & Point Systems
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN
®
TYPE 2
SAFETY LIGHT SCREENS
PICO-GUARD™ Point Systems
Model*
Housing
Material Orientation/Type
Fiber
Description
Fiber
Length
Maximum
Range**
Data
Sheet
SFP30SXP8
304
Stainless
Steel
Straight
30 mm Barrel
Mounting
(25 mm
beam
diameter)
Integral
Polished-End,
PVC Coated Fibers
5 mm Diameter
2.4 m 29 m
111390
SFP30SXP15 4.5 m 24 m
SFP30SXP25 7.5 m 22 m
SFP30SXP50 15 m 14 m
SFP30SXP100 30 m 8.5 m
SFP30SXT8
Integral
Polished-End,
PTFE Coated
Fibers
2.2 mm Diameter
2.4 m 29 m
SFP30SXT15 4.5 m 24 m
SFP30SXT25 7.5 m 22 m
SFP30SXT50 15 m 14 m
SFP30SXT100 30 m 8.5 m
SFP30SS8
Integral
Polished-End,
Polyetheylene
Coated Fibers
2.2 mm Diameter
2.4 m 29 m
SFP30SS15 4.5 m 24 m
SFP30SS25 7.5 m 22 m
SFP30SS50 15 m 14 m
SFP30SS100 30 m 8.5 m
SFP12PXP8
Plastic
Straight
12 mm Barrel
Mounting
(9 mm
beam
diameter)
Integral
Polished-End,
PVC Coated Fibers
5 mm Diameter
2.4 m 6.4 m
111389
SFP12PXP15 4.5 m 4.8 m
SFP12PXP25 7.5 m 3.4 m
SFP12PXP50 15 m 1.5 m
SFP12PXT8 Integral
Polished-End,
PTFE Coated Fibers
2.2 mm Diameter
2.4 m 6.4 m
SFP12PXT15 4.5 m 4.8 m
SFP12PXT25 7.5 m 3.4 m
SFP12PXT50 15 m 1.5 m
SFP12PS8 Integral
Polished-End,
Polyethylene
Coated Fibers
2.2 mm Diameter
2.4 m 6.4 m
SFP12PS15 4.5 m 4.8 m
SFP12PS25 7.5 m 3.4 m
SFP12PS50 15 m 1.5 m
* Order any two Point optical elements with the same beam diameter.
** Maximum range is based on using an emitter and receiver with the same length fiber. Using an emitter and receiver with different length fibers may decrease or
increase range. Using corner mirrors reduces range. See specifications on page 41 for detailed range information.
Download
PDF
40 More information online at bannerengineering.com
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN®
TYPE 2
PICO-GUARD™ Grid & Point Systems
SAFETY LIGHT SCREENS
PICO-GUARD™ Controller (required for a complete system)
Models Description
Product
Information
Data
Sheet
SFCDT-4A1
• The four-optical-channel controller is available
with or without auxiliary channel outputs.
• Two dual-channel Universal Safety Stop
Interface (USSI) inputs can connect to other
safeguarding devices or controllers.
• Two solid-state diverse-redundant 0.5 A
maximum safety outputs (OSSDs).
• Redundant DIP switches determine whether
power-up is auto or manual and whether
output operation is trip or latch.
• Optional external device monitoring (EDM)
allows the system to monitor the status of
external devices such as MPCEs.
• If not needed, up to three optical channels can
be disabled.
Page 108 69761
SFCDT-4A1C
PICO-GUARD™ Interfacing Products
Models Description
Product
Information
Data
Sheet
Interface Modules
IM-T-9A (3 NO)
• Interface modules provide two or three
normally open force-guided relay outputs rated
at 6 A.
• PICO-GUARD monitors these interface
modules when they are connected to the
PICO-GUARD External Device Monitoring
(EDM) inputs.
• Convenient plug-in terminal blocks on a 22.5 mm
DIN-rail mountable housing are included.
Page 132 62822
IM-T-11A (2 NO/1 NC)
Muting Modules
MM-TA-12B • The Muting Module can be used with
PICO-GUARD systems and can temporarily
inhibit a Grid or Point so materials can safely
pass through the beams without stopping the
machinery.
• The module uses redundant microcontroller-
based logic.
Page 123
63517
MMD-TA-12B
116390
MMD-TA-11B
Contactors
Mechanically
Linked Contactors • Pairs of contactors create safety stop circuits
with two normally open contacts in series.
• PICO-GUARD can monitor the circuit because of
the contacts’ force-guided mechanically linked
design.
• Contactors add 10 or 16 amp current carrying
capability to any safety system.
• Auxiliary contacts add 3 or 4 normally open
contacts.
• Suppressors extend the life of an actuating
device that uses a contactor.
• Modular design simplifies assembly and
installation.
Page 186 111881
11-BG00-31-D-024
11-BF16C01-024
Aux. Contacts
11-BGX10-40
11-G484-30
Suppressors
11-BGX77-048
11-G318-48
Download
PDF
Download
PDF
EZ-SCREEN® Systems
41More information online at bannerengineering.com
PICO-GUARD™ Grid & Point Systems
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN
®
TYPE 2
SAFETY LIGHT SCREENS
PICO-GUARD™ Grid & Point Systems Specifications
Operating Range Range information is based on use of the integral polished fibers. The use of SFA-FS Fiber Splice reduces
range by 20%. Do not cut polished fiber ends unless absolutely necessary (if the end is damaged or
contaminated, or must be cut to length). Use only the Model PFC-2 Fiber Cutter to cut fibers, when necessary.
If a polished end is cut, the excess gain is reduced, the advantage of polishing is lost, and the operating range
is reduced.
12 mm Point:
Minimum operating range: 150 mm
Maximum operating range: see table
at right
30 mm Point:
Minimum operating range: 800 mm
Maximum operating range: see table
at right
Grids:
Minimum operating range: 800 mm
Maximum operating range: see table
at right
12 mm Point Maximum Operating Range
SFP12..8 SFP12..15 SFP12..25 SFP12..50
SFP12..8 6.4 m 5.5 m 4.6 m 3 m
SFP12..15 5.5 m 4.8 m 4 m 2.7 m
SFP12..25 4.6 m 4 m 3.4 m 2.1 m
SFP12..50 3 m 2.7 m 2.1 m 1.5 m
30 mm Point Maximum Operating Range
SFP30..8 SFP30..15 SFP30..25 SFP30..50 SFP30..100
SFP30..8 28.7 m 25.9 m 23.2 m 20.1 m 13.7 m
SFP30..15 25.9 m 24.4 m 22.9 m 19.5 m 12.8 m
SFP30..25 23.2 m 22.9 m 21.9 m 17.1 m 12.2 m
SFP30..50 20.1 m 19.5 m 17.1 m 14.0 m 11.0 m
SFP30..100 13.7 m 12.8 m 12.2 m 11.0 m 8.5 m
Grid Maximum Operating Range
SFG..8 SFG..15 SFG..25 SFG..50 SFG..100
SFG..8 31.1 m 29.0 m 26.5 m 21.6 m 14.9 m
SFG..15 29.0 m 27.1 m 24.7 m 20.1 m 14.0 m
SFG..25 26.5 m 24.7 m 22.6 m 18.3 m 12.8 m
SFG..50 21.6 m 20.1 m 18.3 m 14.9 m 10.4 m
SFG..100 14.9 m 14.0 m 12.8 m 10.4 m 7.0 m
Beam Diameter 12 mm Point: 9 mm
30 mm Point: 25 mm
Grids: 25 mm
Effective Aperture Angle (EAA) Type 4 per IEC 61496-2; ±2.5° @ 3 m when used with SFCDT-..
Environmental Rating Points: IEC IP67
Grids: IEC IP65
Operating Conditions Temperature: 0° to +70° C Relative humidity: 95% (non-condensing)
Construction 12 mm Point: black polycarbonate plastic housing; polyethylene, PVC or PTFE coated fibers
30 mm Point: 304 stainless steel housing, glass window; polyethylene, PVC or PTFE coated fibers
Grids: black anodized aluminum housing and label; tempered glass window; zinc end caps; PVC coated fibers
Certifications For a list of certifications see page 236.
PICO-GUARD™ Fiber Optic Controller Specifications
See page 110.
42 More information online at bannerengineering.com
Detailed
Dimensions
MICRO-SCREEN®
Safety Light Screens
• Family is designed for light- to medium-duty
production machinery.
• Full system includes emitter, receiver, controller and
interconnecting cables. Order QD cable separately.
• Emitters and receivers feature ultra-compact
housing with 19 or 32 mm resolution.
• Optional ESD-resistant housing is available.
• System includes floating blanking (one or two
beam), selectable auto power-up, E-stop input and
optional fixed blanking with push-button TEACH
mode programming.
• Controllers offered with DeviceNet™ or muting
MICRO-SCREEN 19 mm Emitters & Receivers. . . .Page 43
MICRO-SCREEN 32 mm Emitters & Receivers. . . . . . . . 44
MICRO-SCREEN Metal Box Controllers . . . . . . . . . . . . . 45
MICRO-SCREEN DIN Module Controllers . . . . . . . . . . . . 46
MICRO-SCREEN Interfacing Products . . . . . . . . . . . . . . 48
MICRO-SCREEN® Emitters & Receivers
MICRO-SCREEN Emitters & Receivers
31.8 mm
L
25.4 mm
Full View of
Available Finishes
MICRO-SCREEN® Systems
SAFETY LIGHT SCREENS
Yellow Painted
Aluminum
Nickel-Plated
ESD
Ultra-compact housing to fit
existing machinery
Swivel bracket for easy alignment
Twelve heights for Standard Series;
seven for V Series
5-pin Euro QD connection standard
QDU-... 5-pin Euro QD cables with
“twisted pair” (see page 175)
NEMA 4, 13; IEC IP65 housing
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN®
TYPE 2
QD CABLES
PAGE 175
).$)#!4/23
PAGE 187
-)22/23
PAGE
204
34!.$3
PAGE
209
,%.33()%,$3
PAGE
213
%.#,/352%3
PAGE
217
DeviceNet™ is a trademark of Rockwell Automation.
5-Pin Euro
BRACKETS
PAGE 190
43More information online at bannerengineering.com
MICRO-SCREEN® Systems
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN
®
TYPE 2
SAFETY LIGHT SCREENS
MICRO-SCREEN® Series,
Emitters & Receivers - 19 mm Resolution
Model* Resolution Defined Area
Housing
Length (L) Range Connection**
Data
Sheet
USE424Y
19 mm Resolution
102 mm 137 mm
9 m 5-Pin Euro QD 48753
USR424Y
USE824Y 203 mm 239 mm
USR824Y
USE1224Y 305 mm 340 mm
USR1224Y
USE1624Y 406 mm 442 mm
USR1624Y
USE2024Y 508 mm 544 mm
USR2024Y
USE2424Y 610 mm 645 mm
USR2424Y
USE2824Y 711 mm 747 mm
USR2824Y
USE3224Y 813 mm 848 mm
USR3224Y
USE3624Y 914 mm 950 mm
USR3624Y
USE4024Y 1016 mm 1052 mm
USR4024Y
USE4424Y 1118 mm 1153 mm
USR4424Y
USE4824Y 1219 mm 1255 mm
USR4824Y
19 mm Resolution
* Nickel-plated emitters and receivers used for ESD safe applications are available. Replace “Y” with “N” in the model number (example, USE424N).
** For a 7.6 m integral cable, add I to model number (example, USE424YI).
For a 300 mm 5-Pin Euro Pigtail QD, add P2 to model number (example, USE424YP2). A model with a QD requires a mating cable (see page 175).
Note: Emitters (example, USE424Y) and receivers (example, USR424Y) are sold separately.
Download
PDF
44 More information online at bannerengineering.com
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN®
TYPE 2
MICRO-SCREEN® Systems
SAFETY LIGHT SCREENS
MICRO-SCREEN® V-Series,
Emitters & Receivers - 32 mm Resolution
Model* Resolution Defined Area
Housing
Length (L) Range Connection**
Data
Sheet
USE2412Y
32 mm Resolution
610 mm 645 mm
9 m 5-Pin Euro QD 48753
USR2412Y
USE3212Y 813 mm 848 mm
USR3212Y
USE4012Y 1016 mm 1052 mm
USR4012Y
USE4812Y 1219 mm 1255 mm
USR4812Y
USE5612Y 1422 mm 1458 mm
USR5612Y
USE6412Y 1626 mm 1661 mm
USR6412Y
USE7212Y 1829 mm 1864 mm
USR7212Y
32 mm Resolution
* Nickel-plated emitters and receivers used for ESD safe applications are available. Replace “Y” with “N” in the model number (example, USE2412N).
** For a 7.6 m integral cable, add I to model number (example, USE2412YI).
For a 300 mm 5-Pin Euro Pigtail QD, add P2 to model number (example, USE2412YP2). A model with a QD requires a mating cable (see page 175).
Note: Emitters (example, USE2412Y) and receivers (example, USR2412Y) are sold separately.
Download
PDF
45More information online at bannerengineering.com
MICRO-SCREEN® Systems
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN
®
TYPE 2
SAFETY LIGHT SCREENS
Welded steel box with polyester
powder paint finish
115/230V ac or 24V dc supply
voltage
One- or two-beam
floating blanking and
selectable power-up
Optional fixed
blanking, muting and
External Device
Monitoring (EDM)
Latch or trip
output
NEMA 13, IEC IP64
housing
E-stop input
MICRO-SCREEN® Metal Box Controllers
MICRO-SCREEN Metal Box Controller
(USCD-1T2 shown)
Detailed
Dimensions
MICRO-SCREEN Metal Box Controller with Muting
(USCC-1L2M shown)
MICRO-SCREEN® Series, Metal Box Controllers
Models
Supply
Voltage
Output
Type
Safety
Outputs
Output
Rating
Aux.
Outputs**
Floating
Blanking
Fixed
Blanking
Data
Sheet
USCT-2T2
24V dc Trip
2 NO
4 amps —
1- or 2-beam
Yes 51597
USCT-2T3 6 amps 1 NC Yes 51597 &
59664
USCD-1T2
115/
230V ac
Trip
4 amps — No 51597
USCD-1T3 6 amps 1 NC No 51597 &
59664
USCD-2T2 4 amps — Yes 51597
USCD-2T3 6 amps 1 NC Yes
51597 &
59664
USCD-2T3E* 6 amps 1 NC Yes
USCD-1L2
Latch
4 amps — No
67173
USCD-2L2 4 amps — Yes
NC = Normally Closed Relay, NO = Normally Open Relay
* The suffix “E” adds external device monitoring input
** All models contain one Reed Relay (see specifications page 53).
210.0 mm
210.0 mm
295.0 mm
260.0 mm
85.0 mm
84.0 mm
Download
PDF
46 More information online at bannerengineering.com
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN®
TYPE 2
MICRO-SCREEN® Systems
SAFETY LIGHT SCREENS
Polycarbonate housing with clear
cover
24V dc supply voltage
One- or two-beam floating
blanking and selectable auto
power-up
Optional fixed blanking and
External Device Monitoring
(EDM)
E-Stop input and latch or trip
output
NEMA 1; IP20 housing
DeviceNet™ compatible
Up to 4 normally open contacts to
control up to two hazards
MICRO-SCREEN® DIN Module Controllers
MICRO-SCREEN DIN Module Controller
(USDINT-1T2 shown)
Detailed
Dimensions
81.0 mm
107.0 mm
115.0 mm
Download
PDF
MICRO-SCREEN® Series, Metal Box Controllers with Muting
Models
Supply
Voltage
Output
Type
Safety
Outputs
Output
Rating
Aux.
Outputs*
Floating
Blanking
Fixed
Blanking
Data
Sheet
USCC-1T2M
115/
230V ac
or
24V dc
Trip
2 NO
4 amps —
1- or 2-beam
No 67690
USCC-1T3M 6 amps 1 NC No
67690
&
59664
USCC-2T2M 4 amps — Yes 67690
USCC-2T3M 6 amps 1 NC Yes
67690
&
59664
USCC-1L2M
Latch
4 amps — No 58764
USCC-2L2M 4 amps — Yes 58764
USCC-2L3M 6 amps 1 NC Yes
58764
&
59644
NC = Normally Closed Relay, NO = Normally Open Relay
* All models contain two Reed Relays (see specifications page 54-55).
Note: External Device Monitoring (EDM) standard on all controllers with muting.
DeviceNet™ is a trademark of Rockwell Automation.
47More information online at bannerengineering.com
MICRO-SCREEN® Systems
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN
®
TYPE 2
SAFETY LIGHT SCREENS
MICRO-SCREEN® Series, DIN Module Controllers
Models
Supply
Voltage
Output
Type
Safety
Outputs**
Output
Rating
Floating
Blanking
Fixed
Blanking
Data
Sheet
USDINT-1T2
24V dc
Trip
2 NO
4 amps 1- or 2-beam
No
48753
USDINT-1T2E* 2 NO 53229
USDINT-1T4 4 NO 48753 &
55631
USDINT-2T2 2 NO
Yes
48753
USDINT-2T4 4 NO 48753 &
55631
USDINT-1L2
Latch
2 NO
No
54202
USDINT-1L4 4 NO 54202 &
55631
USDINT-2L2 2 NO
Yes
54202
USDINT-2L4 4 NO 54202 &
55631
USDINT-1T2D
Trip
plus
DeviceNet™
2 NO
No
48753 &
51699
USDINT-1T4D 4 NO
48753,
51699 &
55631
USDINT-2T2D 2 NO
Yes
48753 &
51699
USDINT-2T4D 4 NO
48753,
51699 &
55631
USDINT-1L2D
Latch
plus
DeviceNet™
2 NO
No
54202 &
54205
USDINT-1L4D 4 NO
54202,
54205 &
55631
USDINT-2L2D 2 NO
Yes
54202 &
54205
USDINT-2L4D 4 NO
54202,
54205 &
55631
NC = Normally Closed Relay, NO = Normally Open Relay
* The suffix “E” adds external device monitoring input
** In addition to safety outputs, all models contain one non-safety Reed Relay auxiliary output (see specifications pages 55-57).
Download
PDF
DeviceNet™ is a trademark of Rockwell Automation.
48 More information online at bannerengineering.com
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN®
TYPE 2
MICRO-SCREEN® Systems
SAFETY LIGHT SCREENS
MICRO-SCREEN® Interfacing Products
Models Description
Product
Information
Data
Sheet
Muting Modules
MM-TA-12B • The Muting Module temporarily inhibits a
safety light screen so materials can safely
pass through the screen without stopping the
machinery.
• The module uses redundant microcontroller-
based logic.
Page 123
63517
MMD-TA-12B
116390
MMD-TA-11B
Contactors
Mechanically
Linked Contactors
• Pairs of contactors create safety stop circuits
with two normally open contacts in series.
• MICRO-SCREEN can monitor the circuit because
of the contacts’ force-guided mechanically
linked design.
• Contactors add 10 or 16 amp current carrying
capability to any safety system.
• Auxiliary contacts add 3 or 4 normally open
contacts.
• Suppressors extend the life of an actuating
device that uses a contactor.
• Modular design simplifies assembly and
installation.
Page 186 111881
11-BG00-31-A12060
11-BG00-31-D-024
11-BF1601-12060
11-BF16C01-024
Aux. Contacts
11-BGX10-40
11-G484-30
Suppressors
11-BGX77-048
11-BGX77-240
11-G318-48
11-G477-240
Download
PDF
49More information online at bannerengineering.com
MICRO-SCREEN® Systems
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN
®
TYPE 2
SAFETY LIGHT SCREENS
MICRO-SCREEN® Metal Box Controller Kits
Kit Model Key
USK2T24243C5Y •
610 mm
19 mm 24
9 m
24V dc
Fixed
&
Floating
Trip
2 NO
Safety
Outputs
&
1 NC Aux.
8 m,
2 each
USK2T24123C5Y 32 mm 12
USK2T24243C5N •19 mm 24
USK2T24123C5N 32 mm 12
USK2D24243C5Y •19 mm 24
115/230V ac
USK2D24123C5Y 32 mm 12
USK2D24243C5N •19 mm 24
USK2D24123C5N 32 mm 12
Kit Model Number
Sensor
Housing
Defined
Area
Resolution
Beams Per
Foot
Range
Supply
Voltage
Blanking
Output
Type
Number of
Outputs
QD Cabling
Yellow
Nickel-
Plated
Model Style
US = MICRO-SCREEN
Model
Style
24K
Kit Fixed-Beam
Blanking Supply
Voltage Output
Type QD Cables Sensor Cable
Termination
Fixed-Beam Blanking
Blank = Without
2 = With
Kit
K = Kit
Quick-Disconnect Cables
C4 = 2 x 5 m
C5 = 2 x 8 m
C6 = 1 x 5 m plus 1 x 8 m
Blank = Integral 8 m cables
Defi ned
Area
Sensor Finish
Y = Yellow polyester paint
N = Nickel plated ESD
Supply Voltage
D = 115/230V ac
T = 24V dc
2 D E
Options
12
Beams
Per Foot
3C5
Finish
P2Y
Defined Area
4 = 102 mm
8 = 203 mm
12 = 305 mm
16 = 406 mm
20 = 508 mm
24 = 610 mm
28 = 711 mm
32 = 813 mm
36 = 914 mm
40 = 1016 mm
44 = 1118 mm
48 = 1219 mm
56 = 1422 mm
64 = 1626 mm
72 = 1829 mm
Beams per Foot
24 = Standard Series
12 = V-Series
Output Type
Blank = Trip
L = Latch
Number of Outputs
Blank= 2 NO Safety Outputs
3 = 2 NO Safety Outputs &
1 NC Aux.
Sensor Cable Termination
I = Integral 8 m cable
Blank = Integral QD connector
P2 = Pigtail QD connector
No. of
Outputs
NOTE: Not all combinations are possible. Contact Banner Engineering Corp. for additional information and/or verification of valid kit model number.
US
Options
E = With External Device
Monitoring (EDM)
Blank = Without
You can purchase a kit that contains an emitter and receiver of equal length and range; standard mounting
brackets; and a pair of quick-disconnect cables. Detailed information about individual kit components is
as follows.
• Metal Box Controllers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 45
• Emitter and Receivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
• Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
• Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
A partial listing of kits is listed below; see Kit Model Key to order other variations.
NC = Normally Closed Relay, NO = Normally Open Relay
50 More information online at bannerengineering.com
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN®
TYPE 2
MICRO-SCREEN® Systems
SAFETY LIGHT SCREENS
NOTE: Not all combinations are possible. Contact Banner Engineering Corp. for additional information and/or verification of valid kit model number.
MICRO-SCREEN® Metal Box Controller with Muting Kits
Kit Model Key
USK2CM2424L3C5Y •
610 mm
19 mm 24
9 m
115/230V ac
or
24V dc
Fixed
&
Floating
Latch
2 NO
Safety
Outputs
&
1 NC Aux.
8 m,
2 each
USK2CM2412L3C5Y 32 mm 12
USK2CM2424L3C5N •19 mm 24
USK2CM2412L3C5N 32 mm 12
Kit Model Number
Sensor
Housing
Defined
Area
Resolution
Beams Per
Foot
Range
Supply
Voltage
Blanking
Output
Type
Number of
Outputs
QD Cabling
Yellow
Nickel-
Plated
Model Style
US = MICRO-SCREEN
Model
Style
24
K
Kit Fixed-Beam
Blanking Supply
Voltage Output
Type QD Cables Sensor Cable
Termination
Fixed-Beam Blanking
Blank = Without
2 = With
Kit
K = Kit
Quick-Disconnect Cables
C4 = 2 x 5 m
C5 = 2 x 8 m
C6 = 1 x 5 m plus 1 x 8 m
Blank = Integral 8 m cables
Defi ned
Area
Sensor Finish
Y = Yellow polyester paint
N = Nickel plated ESD
Supply Voltage
C = 115/230V ac or
24V dc
2C12
Beams
Per Foot
3C5
Finish
P2Y
Beams per Foot
24 = Standard Series
12 = V-Series
Output Type
Blank = Trip
L = Latch
Number of Outputs
Blank = 2 NO Safety Outputs
3 = 2 NO Safety Outputs &
1 NC Aux.
Sensor Cable Termination
I = Integral 8 m cable
Blank = Integral QD connector
P2 = Pigtail QD connector
No. of
Outputs
L
US M
Muting
Muting
M = With
You can purchase a kit that contains an emitter and receiver of equal length and range; standard mounting
brackets; and a pair of quick-disconnect cables. Detailed information about individual kit components is
as follows.
• Metal Box Controllers with Muting . . . . . . . . . . . . . . . . . . . . . . . .Page 46
• Emitter and Receivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
• Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
• Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
A partial listing of kits is listed below; see Kit Model Key to order other variations.
NC = Normally Closed Relay, NO = Normally Open Relay
Defined Area
4 = 102 mm
8 = 203 mm
12 = 305 mm
16 = 406 mm
20 = 508 mm
24 = 610 mm
28 = 711 mm
32 = 813 mm
36 = 914 mm
40 = 1016 mm
44 = 1118 mm
48 = 1219 mm
56 = 1422 mm
64 = 1626 mm
72 = 1829 mm
51More information online at bannerengineering.com
MICRO-SCREEN® Systems
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN
®
TYPE 2
SAFETY LIGHT SCREENS
MICRO-SCREEN® DIN Module Controller Kits
Kit Model Key
USDK2T2424C5Y •
610 mm
19 mm 24
9 m 24V dc
Fixed
&
Floating
Trip
2 NO
Safety
Outputs
8 m,
2 each
USDK2T2412C5Y 32 mm 12
USDK2T2424C5N •19 mm 24
USDK2T2412C5N 32 mm 12
USDK2T2424C5Y •19 mm 24
USDK2T2412C5Y 32 mm 12
USDK2T2424C5N •19 mm 24
USDK2T2412C5N 32 mm 12
Kit Model Number
Sensor
Housing
Defined
Area
Resolution
Beams Per
Foot
Range
Supply
Voltage
Blanking
Output
Type
Number of
Outputs
QD Cabling
Yellow
Nickel-
Plated
Model Style
US = MICRO-SCREEN
Model
Style
24
Kit Fixed-Beam
Blanking Supply
Voltage Output
Type QD Cables Sensor Cable
Termination
Fixed-Beam Blanking
Blank = Without
2 = With
Kit
DK = Kit
Quick-Disconnect Cables*
C4 = 2 x 5 m
C5 = 2 x 8 m
C6 = 1 x 5 m plus 1 x 8 m
Blank = Integral 8 m cables
Defi ned
Area
Sensor Finish
Y = Yellow polyester paint
N = Nickel plated ESD
Supply Voltage
T = 24V dc
2 T E
Options
12
Beams
Per Foot
C5
Finish
P2Y
Beams per Foot
24 = Standard Series
12 = V-Series
Output Type
Blank = Trip
L = Latch
Number of Outputs
Blank= 2 NO Safety Outputs
4 = 4 NO Safety Outputs
Sensor Cable Termination
I = Integral 8 m cable
Blank = Integral QD connector
P2 = Pigtail QD connector
No. of
Outputs
US
Options
E = With External Device
Monitoring (EDM)
D = With DeviceNet
Blank = Without
DK
You can purchase a kit that contains an emitter and receiver of equal length and range; standard mounting
brackets; and a pair of quick-disconnect cables. Detailed information about individual kit components is
as follows.
• Metal DIN Box Controllers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 47
• Emitter and Receivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
• Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
• Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
A partial listing of kits is listed below; see Kit Model Key to order other variations.
NOTE: Not all combinations are possible. Contact Banner Engineering Corp. for additional information and/or verification of valid kit model number.
NC = Normally Closed Relay, NO = Normally Open Relay
Defined Area
4 = 102 mm
8 = 203 mm
12 = 305 mm
16 = 406 mm
20 = 508 mm
24 = 610 mm
28 = 711 mm
32 = 813 mm
36 = 914 mm
40 = 1016 mm
44 = 1118 mm
48 = 1219 mm
56 = 1422 mm
64 = 1626 mm
72 = 1829 mm
52 More information online at bannerengineering.com
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN®
TYPE 2
MICRO-SCREEN® Systems
SAFETY LIGHT SCREENS
MICRO-SCREEN® Emitter & Receiver Specifications
Emitter/Receiver Separation 4" to 48" Emitters and Receivers: 150 mm to 9 m
56" to 72" Emitters and Receivers: 150 mm to 6 m
Minimum Object Sensitivity Standard Series:
19.1 mm floating blanking OFF
31.8 mm 1-beam floating blanking ON
44.5 mm 2-beam floating blanking ON
V-Series:
31.8 mm floating blanking OFF
57.5 mm 1-beam floating blanking ON
82.6 mm 2-beam floating blanking ON
Response Time Light Screens: Less than 38 milliseconds (less than 48 milliseconds with muting option)
E-Stop: Less than 15 milliseconds
Self-Checking Interval 20 milliseconds
Ambient Light Immunity >10,000 lux at 5° angle of incidence
Strobe Light Immunity Totally immune to one Federal Signal Corp. “Fireball” model FB2PST strobe.
Emitter Elements Infrared LEDs; 880 nm peak emission
Status Indicators Emitter: Green LED indicator for power ON indication
Receiver: Red, yellow and green status indicators with the same functions as those on the left side of the
control box (see Control Box Specifications, pages 53-57). Yellow also indicates alignment.
Indicators are visible on three sides of receiver or emitter base.
Emitter and Receiver
Enclosures
Materials: Aluminum extrusion with yellow polyester paint or nickel-plated finish
Rating: NEMA 4, 13; IEC IP65
Mounting Hardware Emitter and receiver each are supplied with a pair of swivel end mount ing brackets. (Emitters and receivers
711 to 914 mm long are supplied with one center support bracket; emitters and receivers 1016 to 1829 mm
long are supplied with two center brackets.) Mount ing brackets are 13-gauge cold-rolled black zinc chromate
fin ished steel.
Cables Emitters and Receivers with Integral Cables (USE/USRxxxxYI):
Cables are 7.6 m long and measure 8.1 mm in diameter. Conductors are 20-gauge. Cables are shielded and
PVC-jacketed.
Emitters and Receivers with Integral (USE/USRxxxxY) or Pigtail (USE/USRxxxxYP2) Quick Disconnect:
Pigtail QD connectors have a 300 mm long cable, terminated with a 5-pin Euro-style quick-disconnect fitting.
Mating interconnect cables are ordered separately (unless a MICRO-SCREEN kit is ordered, see Models and
Accessories, page 175), and are available in lengths of 4.5 m, 7.6 m, and 15 m.
NOTE: Contact factory when cable length exceeding 15 m is required. Use only Banner cables, which
incorporate a shielded “twisted pair” for noise immunity on RS485 data communications lines. Use of
other cables may result in “nuisance” trips or lockouts.
Optical Performance This system meets ± 2.5° requirements of IEC 61496-2 section 5.2.9 (Type 4)
Operating Conditions Temperature: 0° to +50° C Relative humidity: 95% maximum (non-condensing)
Certifications For a list of certifications see page 236.
53More information online at bannerengineering.com
MICRO-SCREEN® Systems
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN
®
TYPE 2
SAFETY LIGHT SCREENS
MICRO-SCREEN® Metal Box Controller Specifications
System Power Requirements USCD-.. models: 115/230V ac ±15% (50/60 Hz), 55 VA
USCT-.. models: 24V dc ±15% @ 1.5 amp max.
Fuse Rating (F2) 115V ac: 1 amp, 250V ac; 230V ac: 0.5 amp, 250V
24V dc: 2 amp, 250V
Response Time Light Screens: Less than 38 milliseconds
E-Stop: Less than 15 milliseconds
Status Indicators Control Box and Receiver:
Solid LED Flashing LED
Red BLOCKED/LATCHED LOCKOUT
Green CLEAR BLANKING ON
Yellow RESET Double Flash = Waiting for System Key RESET at Power-up
Single Flash = ALIGNMENT. Flash rate in creas es with the number of
sensing beams “made”, solid yellow when aligned and
defined area is clear
Diagnostic Indicator Two-digit numeric display indicates cause of lockout condition and total number of beams blocked.
Controls and Adjustments Keyed RESET of system lockout and latched conditions
Floating blanking selection switches and fixed blanking programming switches
Auto Power-up On-Off switches
E-Stop Switch Input The Emergency Stop switch must offer two normally closed contacts and be capable of switching
50 mA @ 30V dc. Total resistance, including wiring and all switches, must not exceed 30 Ω for proper operation.
Functional stop category 0 per NFPA 79 and EN 418, Safety Category 4 per EN 954-1. Simultaneity requirement
less than 100 milliseconds.
External Device Monitoring
(EDM) Input*
Terminals must open within 200 milliseconds of the FSD outputs closing (i.e., a clear condition) and must
close within 200 milliseconds of the FSD outputs opening (i.e., a blocked condition) or a lockout will occur. The
monitoring contacts must be forced-guided (or captive contact) to maintain control reliability of the machine
control circuit and must be capable of reliably switching 15 to 50V dc at 20 to 100 mA.
Test Input Terminals must be closed for a minimum of 0.05 seconds in order to guar an tee a test input signal. The switch-
ing device used must be capable of switching 15-50V dc at 20 to 100 mA.
Reset Input Terminals must be closed for a minimum of 0.5 seconds in order to guarantee a reset. The switching device
must be capable of switching 15-50V dc at 20-100 mA.
Auxiliary Monitor Relay Reed relay; 125V ac or dc max., 500 mA max. (10 VA max., resistive load)
Safety Outputs Forced-guided contact relay (resistive load).
USCD-..2 & USCT-..2: FSD1 & 2, SSD = 250V ac max., 4 amp max.
USCD-..3 & USCT-..3: FSD1 & 2, CNC = 250V ac max., 6 amp max.
SSD = 250V ac max., 4 amp max.
Mechanical life: 10,000,000 operations (minimum).
Electrical life: 100,000 operations (typical @ 1.0 kVA switching power).
Arc suppression is recommended when switching inductive loads.
Enclosure Material: Welded steel box with black polyester powder paint finish
Rating: NEMA 13; IEC IP64
Operating Conditions Temperature: 0° to +50° C Relative humidity: 95% maximum (non-condensing)
FMEA Tested Per re quire ments IEC 61496-1 (type 4)
Applications Notes Use of fixed blanking requires sensors with 16 or more light beams. Up to 12 beams or 30% of the total
number of beams in the array may be blanked, whichever is less. Call factory for applications assistance if a
greater number of blanked beams is required.
Certifications For a list of certifications see page 236.
Wiring Diagrams 2 FSDs, 1 SSD and Power Monitoring: WD017 (p. 255)
* External Device Monitoring (EDM) models only.
54 More information online at bannerengineering.com
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN®
TYPE 2
MICRO-SCREEN® Systems
SAFETY LIGHT SCREENS
MICRO-SCREEN® Metal Box Controller with Muting Specifications
System Power Requirements 115V ac (50/60Hz) ± 15% @ 500 mA (50 VA),
230V ac (50/60Hz) ± 15% @ 250 mA (50 VA), or
24V dc ±15%, 10% max. ripple, @ 2.5 A (60 W)
Fuse Rating (F2) 115V ac: 1.0 A ac @ 250V ac (supplied)
230V ac: 500 mA @ 250V ac
+24V dc: Internal resettable
Response Time Light Screen: Less than 48 milliseconds E-Stop: Less than 15 milliseconds
Status LED Indicators Light Screen Indicators (left column of LEDs):
Solid LED Flashing LED
Red BLOCKED/LATCHED LOCKOUT
Green CLEAR BLANKING ON
Yellow RESET Double Flash = Waiting for
Single Flash = ALIGNMENT. Flash rate in creas es with the number of
sensing beams “made”, solid yellow when aligned and
defined area is clear
System Indicators (right column of LEDs):
Solid LED Flashing LED
Red OVERRIDE LOCKOUT
Green OUTPUT ON (Not Applicable)
(FSD1 & FSD2 closed)
Yellow RESET Double Flash = Waiting for System Key Reset at Power-up
(System) Single Flash = Waiting for System Key Reset at latched condition (manual
reset of system after blockage has been removed)
Diagnostic Displays Light Screen Diagnostic Display (left window) is a two-digit numeric display that indicates the cause of
lockout conditions and total number of beams blocked.
System Diagnostic Display (right window) is a two-digit numeric display that indicates the cause of lockout
conditions and the amount of time, in seconds, remaining for the backdoor timer.
Controls and Adjustments • Light Screen Key Reset after power-up and light screen lockouts
• Selection switches to enable floating blanking
• Program switches to enable fixed blanking (USCC-2.. only)
• Light Screen and System Auto Power-up selection switches
• System Key Reset after power-up, system lockouts, and latched conditions
• Selection switches for Monitored or Non-Monitored Muting indicator
• Selection switches for One-Way or Two-Way (directional/non-directional) Muting
• Selection switches for One-Channel or Two-Channel Monitoring (EDM)
• Selection switches for Backdoor Timer settings and Mute-on-Power-Up
E-Stop Switch Input The Emergency Stop switch must offer two normally closed contacts and be capable of switching
50 mA @ 30V dc. Total resistance, including wiring and all switches, must not exceed 30 Ω for proper
operation. Functional stop category 0 per NFPA 79 and EN 418, Safety Category 4 per EN 954-1. Simultaneity
requirement less than 100 milliseconds.
Light Screen Test Input Terminals must be closed for a minimum of 0.05 seconds in order to guarantee a test. The switching device
must be capable of switching 15-50V dc at 20-100 mA.
Light Screen and
System Reset Inputs
Terminals must be closed for a minimum of 0.5 seconds in order to guarantee a reset. The switching device
must be capable of switching 15-50V dc at 20-100 mA.
External Device Monitoring
(EDM) Input(s)
Two pairs of terminals are provided to monitor the state of external devices that are being controlled by the
FSD outputs. The device must be capable of switching 15-50V dc at 20-100 mA.
Mute Enable Input Terminals must be closed in order to start a mute; opening this input after mute has begun has no effect. The
switching device must be capable of switching 15-50V dc at 20-100mA.
Override Inputs The two-channel inputs must be closed within 3 seconds of each other (simultaneity requirement) and held
closed during the 10-second Override. To initiate a subsequent Override, open both channels, wait 3 seconds,
and then re-close both channels (within 3 seconds). The switching devices must be capable of switching
15-50V dc at 20-100 mA.
Muting Device Input The muting devices work in pairs (M1 and M2, M3 and M4) and are required to be “closed” within 3 seconds of
each other (simultaneity requirement) to initiate a mute (assuming all other conditions are met). Each muting
device must be capable of switching 15-50V dc at 20-100 mA.
Light Screen and System
Aux. Monitor Relay Outputs
Reed relay; 125V ac/dc max at 500 mA max. (10 VA maximum, resistive load)
55More information online at bannerengineering.com
MICRO-SCREEN® Systems
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN
®
TYPE 2
SAFETY LIGHT SCREENS
MICRO-SCREEN® Metal Box Controller with Muting Specifications
Safety Outputs Forced-guided contact relay (resistive load).
USCC-..2: FSD1 & 2, SSD = 250V ac max., 4 amp max.
USCC-..3: FSD1 & 2, CNC = 250V ac max., 6 amp max.
SSD = 250V ac max., 4 amp max.
Mechanical life: 10,000,000 operations (minimum).
Electrical life: 100,000 operations (typical @ 1.0 kVA switching power).
Arc suppression is recommended when switching inductive loads.
Mute Lamp Output A monitored or non-monitored (selectable) sinking output. If monitoring has been selected, the current draw
must be within 10 mA to 360 mA.
Max. switching voltage: 30V dc
Max. switching current: 360 mA
Max. switching current: 10 mA
Saturation voltage: ≤ 1.5V dc
Auxiliary DC Supply Output 24V dc ± 25%, 500 mA max
Enclosure Material: Welded steel box with black polyester powder paint finish.
Rating: NEMA 13; IEC IP64
Operating Conditions Temperature: 0° to +50° C Relative humidity: 95% maximum (non-condensing)
FMEA Tested Per requirements of IEC 61496-1 (type 4)
Applications Notes Use of fixed blanking requires sensors with 16 or more light beams. Up to 12 beams or 30% of the total
number of beams in the array may be blanked, whichever is less. Call factory for applications assistance if a
greater number of blanked beams is required.
Certifications For a list of certifications see page 236.
Wiring Diagrams 2 FSDs and 2-Channel EDM: WD018 (p. 255)
MICRO-SCREEN® DIN Module Controller Specifications
System Power Requirements 24V dc ±15%, 10% max. ripple, 1.5 amps max.
Fuse Rating 2 amp, 250 V (3 AG or 5 x 20 mm slow blow)
Response Time Light Screens: Less than 38 milliseconds
E-Stop: Less than 15 milliseconds
Status Indicators
(on control module and receiver)
Control Box and Receiver:
Solid LED Flashing LED
Red BLOCKED/LATCHED LOCKOUT
Green CLEAR BLANKING ON
Yellow RESET Double Flash = Waiting for System Key Reset at Power-up
Single Flash = ALIGNMENT. Flash rate in creas es with the number of
sensing beams “made”, solid yellow when aligned and
defined area is clear
Diagnostic Indicator Two-digit numeric display indicates cause of lockout condition and total number of beams blocked.
Controls and Adjustments Keyed Reset of system lockout and latched conditions
Floating Blanking selection switches and Fixed Blanking programming switches
Auto Power-up On-Off switches
E-Stop Switch Input The Emergency Stop switch must offer two normally closed contacts and be capable of switching
50 mA @ 30V dc. Total resistance, including wiring and all switches, must not exceed 30 Ω for proper operation.
Functional stop category 0 per NFPA 79 and EN 418, Safety Category 4 per EN 954-1. Simultaneity requirement
less than 100 milliseconds.
External Device Monitoring
(EDM) Input*
Terminals must open within 200 milliseconds of the FSD outputs closing (i.e., a clear condition) and must close
within 200 milliseconds of the FSD outputs opening (i.e., a blocked condition) or a lockout will occur.
The monitoring contacts must be forced-guided (or captive contact) to maintain control reliability of the
machine control circuit and must be capable of reliably switching 15 to 50V dc at 20 to 100 mA.
Test Input (except EDM models) Terminals must be closed for a minimum of 0.05 seconds in order to guarantee a test input signal. The
switching device used must be capable of switching 15-50V dc at 20 to 100 mA.
AUX Non-Safety Output
Contact
Reed relay; 125V ac or dc max., 500 mA max. (10 VA max., resistive load)
MICRO-SCREEN® Metal Box Controller with Muting Specifications (cont’d)
* External Device Monitoring (EDM) models only.
56 More information online at bannerengineering.com
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN®
TYPE 2
MICRO-SCREEN® Systems
SAFETY LIGHT SCREENS
MICRO-SCREEN® DIN Module Controller Specifications
Safety Outputs Forced-guided contact relays (resistive load).
FSD1 & 2, SSD = 250V ac max., 4 amps max.
Mechanical life: 10,000,000 operations (minimum).
Electrical life (at full rated load): 100,000 operations (typical).
Arc suppression is recommended when switching inductive loads.
Note: Controllers with model suffix “2” have two FSD output contacts and those with model suffix “4” have
four FSD output contacts.
Enclosure Material: gray polycarbonate, clear polycarbonate cover
Rating: NEMA 1; IP20
Operating Conditions Temperature: 0° to +50° C Relative humidity: 95% maximum (non-condensing)
FMEA Tested Per requirements IEC 61496-1
Application Notes Use of fixed blanking requires sensors with 16 or more light beams. Up to 12 beams or 30% of the total
number of beams in the array may be blanked, whichever is less. Call factory for applications assistance if a
greater number of blanked beams is required.
Certifications For a list of certifications see page 236.
Wiring Diagrams 2 FSDs, 1 SSD and Power Monitoring: WD019 (p. 256)
2 FSDs, 1 SSD and 1-Channel EDM: WD020 (p. 256)
4 FSDs, 1 SSD and Power Monitoring: WD021 (p. 257)
MICRO-SCREEN® DIN Module with DeviceNet™ Specifications
Device Net Power 11 to 25V dc; 80 mA - supplied by DeviceNet BUS Network
Response Time Light Screen: Less than 38 milliseconds (all lengths)
E-Stop: Less than 15 milliseconds
Status Indicators
(on control module and receiver)
Solid LED Flashing LED
Red BLOCKED/LATCHED LOCKOUT
Green CLEAR BLANKING ON
Yellow RESET Double Flash = Waiting for System Key Reset at Power-up
Single Flash = ALIGNMENT. Flash rate in creas es with the
number of sensing beams “made”, solid yellow
when aligned and defined area is clear
Network status indicator:
A bi-color (red/green) LED visible on the control module indicates network status:
Green Steady On-line, connected to master
Flashing On-line, not connected/allocated to master; if Autobaud is
ON, address and baud rate OK
Red Steady Critical network fault or duplicate mode address detected
Flashing Connection time-out or no power to light screen
OFF No network power or off-line
Green/Red/OFF Autobaud detecting network baud rate
Diagnostic Indicator Two-digit numeric display indicates cause of lockout condition and total number of beams blocked.
Controls and Adjustments Keyed RESET of system lockout and latched conditions
Floating blanking selection switches and fixed blanking programming switches
Auto Power-up On-Off switches
E-Stop Switch Input The Emergency Stop switch must offer two normally closed contacts and be capable of switching
50 mA @ 30V dc. Total resistance, including wiring and all switches, must not exceed 30 Ω for proper
operation. Functional stop category 0 per NFPA 79 and EN 418, Safety Category 4 per EN 954-1. Simultaneity
requirement less than 100 milliseconds.
Test Input Terminals must be closed for a minimum of 0.05 seconds in order to guarantee a test input signal. The
switching device used must be capable of switching 15-50V dc at 20 to 100 mA.
MICRO-SCREEN® DIN Module Controller Specifications (cont’d)
DeviceNet™ is a trademark of Rockwell Automation.
57More information online at bannerengineering.com
MICRO-SCREEN® Systems
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN
®
TYPE 2
SAFETY LIGHT SCREENS
MICRO-SCREEN® DIN Module with DeviceNet™ Specifications
DeviceNet™ Configuration Vendor Code 12 (Banner Engineering Corp.)
Device Type 130 (Safety Light Screen)
Product Code
USDINT-1T2D/USDINT-1T4D 1
USDINT-2T2D/USDINT-2T4D 2
USDINT-1L2D/USDINT-1L4D 3
USDINT-2L2D/USDINT-2L4D 4
Connection Types Supported Explicit Message, Poll, Change of State
Network Address 0-63 (Manual Switches or Network configured)
Baud Rate Supported Autobaud or Network configured (125K, 250K, 500K)
(Factory setting is Autobaud ON)
EDS File Names
USDINT-1T2D/USDINT-1T4D 130_1_2.eds
USDINT-2T2D/USDINT-2T4D 130_2_2.eds
USDINT-1L2D/USDINT-1L4D 130_3_1.eds
USDINT-2L2D/USDINT-2L4D 130_4_1.eds
Bit Map Icon File Name 130.bmp
EDS and Bitmap files on 3.5” floppy disk supplied with controller (p/n 52243)
Poll and COS I/O
Assembly Instances
The MICRO-SCREEN device I/O assemblies consist of:
• Poll: One product specific input assembly containing operating mode, status of defined area, status of output
relays, status of inputs (Key Reset, Test, and E-Stop), noise detected, number of sensor beams, number
of beams blocked, Auto Power-up switch settings, COS trigger setting, autobaud setting, floating blanking
switch settings and number of fixed beams (Fixed Blanking models only).
• COS: One product-specific input assembly containing the operating mode and defined area status.
Auxiliary Monitor Relay Reed relay; 125V ac or dc max., 500 mA max. (10 VA max., resistive load)
Safety Outputs Forced-guided contact relays (resistive load).
FSD1 & 2, SSD = 250V ac max., 4 amps max.
Mechanical life: 10,000,000 operations (minimum).
Electrical life (at full rated load): 100,000 operations (typical).
Arc suppression is recommended when switching inductive loads.
Note: Controllers with model suffix “2” have two FSD output contacts and those with model suffix “4” have
four FSD output contacts.
Enclosure Material: gray polycarbonate, clear polycarbonate cover
Rating: NEMA 1; IP20
Operating Conditions Temperature: 0° to +50° C Relative humidity: 95% maximum (non-condensing)
FMEA Tested Per requirements IEC 61496-1
Application Notes Use of fixed blanking requires sensors with 16 or more light beams. Up to 12 beams or 30% of the total
number of beams in the array may be blanked, whichever is less. Call factory for applications assistance if a
greater number of blanked beams is required.
Certifications For a list of certifications see page 236.
Wiring Diagrams 2 FSDs, 1 SSD and Power Monitoring: WD019 (p. 256)
2 FSDs, 1 SSD and 1-Channel EDM: WD020 (p. 256)
4 FSDs, 1 SSD and Power Monitoring: WD021 (p. 257)
MICRO-SCREEN® DIN Module with DeviceNet™ Specifications (cont’d)
DeviceNet™ is a trademark of Rockwell Automation.
58 More information online at bannerengineering.com
MINI-SCREEN® Emitters & Receivers
38.1 mm
L
38.1 mm
Full View of
Available Finishes
Detailed
Dimensions
Yellow Painted
Aluminum
Black Anodized
Aluminum
MINI-SCREEN 19 mm Emitters & Receivers . . . . .Page 59
MINI-SCREEN 25 mm Emitters & Receivers . . . . . . . . . 61
MINI-SCREEN 38 mm Heavy-Duty Emitters & Receivers. . 63
MINI-SCREEN Metal Box Controllers . . . . . . . . . . . . . . . 64
MINI-SCREEN DIN Module Controllers. . . . . . . . . . . . . . 65
MINI-SCREEN Interfacing Products . . . . . . . . . . . . . . . . 66
Safety Light Screen
Systems
• Family is designed for heavy-duty production
machinery.
• Full system includes emitter, receiver, controller
and interconnecting cables. Order QD cables
separately.
• Standard or heavy-duty housing are available for
emitters and receivers.
• Emitters and receivers feature compact housing
with 19, 25 and 38 mm resolution.
• Explosion-proof enclosures are available.
• Systems include floating blanking (one- or two- beam),
selectable auto power-up and optional fixed blanking.
MINI-SCREEN®
19 mm resolution with maximum
9 m range or 25 mm resolution with
maximum 18 m range
Yellow painted or black anodized
aluminum housing with rugged
end caps
Twelve heights from 114 to 1219 mm
Status indicators
Swivel brackets for easy alignment
5-pin Mini QD connection standard
QDS-... 5-pin Mini QD cables with
“twisted pair” (see page 179)
NEMA 4, 13; IEC IP65 housing
SAFETY LIGHT SCREENS
MINI-SCREEN® Systems
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN®
TYPE 2
BRACKETS
PAGE 190
QD CABLES
PAGE 179
-)22/23
PAGE
204
34!.$3
PAGE
209
,%.33()%,$3
PAGE
213
%.#,/352%3
PAGE
217
5-Pin Mini
).$)#!4/23
PAGE 187
59More information online at bannerengineering.com
MINI-SCREEN® Systems
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN
®
TYPE 2
SAFETY LIGHT SCREENS
MINI-SCREEN®
, Emitters & Receivers - 19 mm Resolution
Model Number Housing Defined Area
Housing
Length (L) Range Connection*
Data
Sheet
MSE424Y
19 mm Resolution
114 mm 153 mm
9 m 5-Pin Mini QD 39022
MSR424Y
MSE424
19 mm Resolution
MSR424
MSE824Y
19 mm Resolution
215 mm 254 mm
MSR824Y
MSE824
19 mm Resolution
MSR824
MSE1224Y
19 mm Resolution
305 mm 356 mm
MSR1224Y
MSE1224
19 mm Resolution
MSR1224
MSE1624Y
19 mm Resolution
406 mm 457 mm
MSR1624Y
MSE1624
19 mm Resolution
MSR1624
MSE2024Y
19 mm Resolution
508 mm 558 mm
MSR2024Y
MSE2024
19 mm Resolution
MSR2024
MSE2424Y
19 mm Resolution
610 mm 659 mm
MSR2424Y
MSE2424
19 mm Resolution
MSR2424
19 mm Resolution Yellow Housing 19 mm Resolution Black Housing
* For a 305 mm 5-Pin Mini Pigtail QD, add P to model number (example, MSE424YP). A model with a QD requires a mating cable (see page 179).
Note: Emitters (example, MSE424Y) and receivers (example, MSR424Y) are sold separately.
Download
PDF
60 More information online at bannerengineering.com
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN®
TYPE 2
MINI-SCREEN® Systems
SAFETY LIGHT SCREENS
MINI-SCREEN®
, Emitters & Receivers - 19 mm Resolution
Model Number Housing Defined Area
Housing
Length (L) Range Connection*
Data
Sheet
MSE2824Y
19 mm Resolution
711 mm 761 mm
9 m 5-Pin Mini QD 39022
MSR2824Y
MSE2824
19 mm Resolution
MSR2824
MSE3224Y
19 mm Resolution
813 mm 862 mm
MSR3224Y
MSE3224
19 mm Resolution
MSR3224
MSE3624Y
19 mm Resolution
914 mm 963 mm
MSR3624Y
MSE3624
19 mm Resolution
MSR3624
MSE4024Y
19 mm Resolution
1016 mm 1064 mm
MSR4024Y
MSE4024
19 mm Resolution
MSR4024
MSE4424Y
19 mm Resolution
1118 mm 1166 mm
MSR4424Y
MSE4424
19 mm Resolution
MSR4424
MSE4824Y
19 mm Resolution
1219 mm 1267 mm
MSR4824Y
MSE4824
19 mm Resolution
MSR4824
19 mm Resolution Yellow Housing 19 mm Resolution Black Housing
* For a 305 mm 5-Pin Mini Pigtail QD, add P to model number (example, MSE2824YP). A model with a QD requires a mating cable (see page 179).
Note: Emitters (example, MSE2824Y) and receivers (example, MSR2824Y) are sold separately.
Download
PDF
(cont’d)
61More information online at bannerengineering.com
MINI-SCREEN® Systems
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN
®
TYPE 2
SAFETY LIGHT SCREENS
MINI-SCREEN®, Emitters & Receivers - 25 mm Resolution
Model Number Housing Defined Area
Housing
Length (L) Range Connection*
Data
Sheet
MSXLE424Y
25 mm Resolution
114 mm 153 mm
18 m 5-Pin Mini QD 39022
MSXLR424Y
MSXLE424
25 mm Resolution
MSXLR424
MSXLE824Y
25 mm Resolution
215 mm 254 mm
MSXLR824Y
MSXLE824
25 mm Resolution
MSXLR824
MSXLE1224Y
25 mm Resolution
305 mm 356 mm
MSXLR1224Y
MSXLE1224
25 mm Resolution
MSXLR1224
MSXLE1624Y
25 mm Resolution
406 mm 457 mm
MSXLR1624Y
MSXLE1624
25 mm Resolution
MSXLR1624
MSXLE2024Y
25 mm Resolution
508 mm 558 mm
MSXLR2024Y
MSXLE2024
25 mm Resolution
MSXLR2024
MSXLE2424Y
25 mm Resolution
610 mm 659 mm
MSXLR2424Y
MSXLE2424
25 mm Resolution
MSXLR2424
25 mm Resolution Yellow Housing 25 mm Resolution Black Housing
* For a 305 mm 5-Pin Mini Pigtail QD, add P to model number (example, MSXLE424YP). A model with a QD requires a mating cable (see page 179).
Note: Emitters (example, MSXLE424Y) and receivers (example, MSXLR424Y) are sold separately.
Download
PDF
62 More information online at bannerengineering.com
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN®
TYPE 2
MINI-SCREEN® Systems
SAFETY LIGHT SCREENS
MINI-SCREEN®, Emitters & Receivers - 25 mm Resolution
Model Number Housing Defined Area
Housing
Length (L) Range Connection*
Data
Sheet
MSXLE2824Y
25 mm Resolution
711 mm 761 mm
18 m 5-Pin Mini QD 39022
MSXLR2824Y
MSXLE2824
25 mm Resolution
MSXLR2824
MSXLE3224Y
25 mm Resolution
813 mm 862 mm
MSXLR3224Y
MSXLE3224
25 mm Resolution
MSXLR3224
MSXLE3624Y
25 mm Resolution
914 mm 963 mm
MSXLR3624Y
MSXLE3624
25 mm Resolution
MSXLR3624
MSXLE4024Y
25 mm Resolution
1016 mm 1064 mm
MSXLR4024Y
MSXLE4024
25 mm Resolution
MSXLR4024
MSXLE4424Y
25 mm Resolution
1118 mm 1166 mm
MSXLR4424Y
MSXLE4424
25 mm Resolution
MSXLR4424
MSXLE4824Y
25 mm Resolution
1219 mm 1267 mm
MSXLR4824Y
MSXLE4824
25 mm Resolution
MSXLR4824
25 mm Resolution Yellow Housing 25 mm Resolution Black Housing
* For a 305 mm 5-Pin Mini Pigtail QD, add P to model number (example, MSXLE2824YP). A model with a QD requires a mating cable (see page 179).
Note: Emitters (example, MSXLE2824Y) and receivers (example, MSXLR2824Y) are sold separately.
Download
PDF
(cont’d)
63More information online at bannerengineering.com
MINI-SCREEN® Systems
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN
®
TYPE 2
SAFETY LIGHT SCREENS
MINI-SCREEN® Heavy-Duty Emitters & Receivers - 38 mm Resolution
Model Number Resolution Defined Area
Housing
Length (L) Range Connection*
Data
Sheet
MSXLHDE2412Y
38 mm Resolution
610 mm 625 mm
18 m 5-Pin Mini QD 69018
MSXLHDR2412Y
MSXLHDE3212Y 813 mm 826 mm
MSXLHDR3212Y
MSXLHDE4012Y 1016 mm 1029 mm
MSXLHDR4012Y
MSXLHDE4812Y 1219 mm 1229 mm
MSXLHDR4812Y
MSXLHDE5612Y 1422 mm 1433 mm
MSXLHDR5612Y
MSXLHDE6412Y 1626 mm 1633 mm
MSXLHDR6412Y
MSXLHDE7212Y 1829 mm 1836 mm
MSXLHDR7212Y
38 mm Resolution
* For a 305 mm 5-Pin Mini Pigtail QD, add P to model number (example, MSXLHDE2412YP). A model with a QD requires a mating cable (see page 179).
Note: Emitters (example, MSXLHDE2412Y) and receivers (example, MSXLHDR2412Y) are sold separately.
Robust, impact-resistant housing
38 mm resolution with 18 m range
Seven heights from 610 to 1829 mm
High immunity to ambient light
interference
Status indicators
Swivel bracket for easy alignment
5-pin Mini QD connection standard
QDS-... 5-pin Mini QD with “twisted
pair” (see page 179)
NEMA 4, 13; IEC IP65 housing
MINI-SCREEN® Heavy-Duty Emitters & Receivers
MINI-SCREEN Heavy-Duty Emitters & Receivers
Detailed
Dimensions
55.0 mm
L
52.0 mm
Full View
Yellow Painted Aluminum
Downloa
d
PDF
64 More information online at bannerengineering.com
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN®
TYPE 2
MINI-SCREEN® Systems
SAFETY LIGHT SCREENS
MINI-SCREEN® Series, Metal Box Controllers
Models
Supply
Voltage
Output
Type
Safety
Outputs*
Output
Rating
Aux.
Outputs**
Floating
Blanking
Fixed
Blanking
Data
Sheet
MSCT-1
24V dc Trip
2 NO
4 amps —
2-beam No
39022
MSCT-1T3 6 amps 1 NC 59664 &
39022
MSCT-2 4 amps —
1- or 2-beam Yes
47295
MSCT-2T3 6 amps 1 NC 59664 &
47295
MSCA-1
115V ac
Trip
4 amps —
2-beam No
39022
MSCA-1T3 6 amps 1 NC 59664 &
39022
MSCA-1L2
Latch
4 amps — 55702
MSCA-1L3 6 amps 1 NC 59664 &
55702
MSCA-1L3E* 6 amps 1 NC 46904 &
55702
MSCA-1S2E* Trip /Latch
Selectable
4 amps — 39022
MSCA-1S3E* 6 amps 1 NC 39022
MSCB-1
230V ac
Trip
4 amps — 39022
MSCB-1T3 6 amps 1 NC 59664 &
39022
MSCB-1L2 Latch 4 amps — 55702
MSCD-2
115/230V ac Trip
4 amps —
1- or 2-beam Yes
47295
MSCD-2T3 6 amps 1 NC 59644 &
47295
Welded steel box with
polyester powder paint
finish
115/230V ac or 24V dc
supply voltage
Floating blanking and
selectable auto
power-up
Optional fixed
blanking, muting
and External Device
Monitoring (EDM)
Latch or trip output
NEMA 13, IEC IP64
housing
MINI-SCREEN® Metal Box Controllers
MINI-SCREEN Metal Box Controller
(MSCA-1 shown)
MINI-SCREEN Metal Box Controller with Muting
(MSCC-2T2M shown)
244.0 mm
210.0 mm
295.0 mm
260.0 mm
85.0 mm
84.0 mm
NC = Normally Closed Relay, NO = Normally Open Relay
* The suffix “E” adds external device monitoring input
** All models contain one Reed Relay (see specifications page 73)
Download
PDF
65More information online at bannerengineering.com
MINI-SCREEN® Systems
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN
®
TYPE 2
SAFETY LIGHT SCREENS
Polycarbonate housing with
removable terminal blocks and
clear cover
24V dc supply voltage
Floating blanking
and selectable auto
power-up
Latch or trip
output
Dual models
for two emitter/
receiver pairs
NEMA 1; IP20 housing
MINI-SCREEN® DIN Module Controllers
MINI-SCREEN Dual DIN Module Controller
(MDSDINT-1T2 shown)
Detailed
Dimensions
83.8 mm
149.0 mm
110.0 mm
MINI-SCREEN DIN Module Controller
(MSDINT-1 shown)
100.0 mm
75.0 mm
110.0 mm
Download
PDF
MINI-SCREEN Series, DIN Module Controllers
Models
Supply
Voltage
Output
Type
Safety
Outputs*
Output
Rating
Floating
Blanking
Fixed
Blanking
E-Stop
Input
Light Screen
Pairs/Controller
Data
Sheet
MSDINT-1
24V dc
Trip
2 NO 4 amps
2-beam
No
No
1 Pair
44895
MSDINT-1L2 Latch
MDSDINT-1T2 Trip
1- or
2-beam Yes
2 Pairs
47297 &
60159
MDSDINT-1L2 Latch
NC = Normally Closed Relay, NO = Normally Open Relay
* In addition to safety outputs, all models contain either one or two non-safety Reed Relay auxiliary outputs (see specifications pages 76-77).
MINI-SCREEN® Series, Metal Box Controllers with Muting
Models
Supply
Voltage
Output
Type
Safety
Outputs
Output
Rating
Aux.
Outputs**
Floating
Blanking
Fixed
Blanking
Data
Sheet
MSCC-2T2M 115/230V ac
or
24V dc
Trip
2 NO
4 amps —
1- or 2-beam Yes
64723
MSCC-2T3M 6 amps 1 NC
MSCC-2L2M 115/230V ac
or
24V dc
Latch
4 amps —
61409
MSCC-2L3M 6 amps 1 NC
NC = Normally Closed Relay, NO = Normally Open Relay
* All models contain two Reed Relays (see specifications pages 74-75)
Note: External Device Monitoring (EDM) standard on all controllers with muting.
Download
PDF
66 More information online at bannerengineering.com
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN®
TYPE 2
MINI-SCREEN® Systems
SAFETY LIGHT SCREENS
MINI-SCREEN® Interfacing Products
Models Description
Product
Information
Data
Sheet
Muting Modules
MM-TA-12B • The Muting Module temporarily inhibits a
safety light screen so materials can safely
pass through the screen without stopping the
machinery.
• The module uses redundant microcontroller-
based logic.
Page 123
63517
MMD-TA-12B
116390
MMD-TA-11B
Contactors
Mechanically
Linked Contactors
• Pairs of contactors create safety stop circuits
with two normally open contacts in series.
• MINI-SCREEN can monitor the circuit because of
the contacts’ force-guided mechanically linked
design.
• Contactors add 10 or 16 amp current carrying
capability to any safety system.
• Auxiliary contacts add 3 or 4 normally open
contacts.
• Suppressors extend the life of an actuating
device that uses a contactor.
• Modular design simplifies assembly and
installation.
Page 186 111881
11-BG00-31-A12060
11-BG00-31-D-024
11-BF1601-12060
11-BF16C01-024
Aux. Contacts
11-BGX10-40
11-G484-30
Suppressors
11-BGX77-048
11-BGX77-240
11-G318-48
11-G477-240
Download
PDF
67More information online at bannerengineering.com
MINI-SCREEN® Systems
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN
®
TYPE 2
SAFETY LIGHT SCREENS
MINI-SCREEN® Metal Box Controller Kits - Floating Blanking
Kit Model Key
Model Style
MS = MINI-SCREEN
Model
Style
24K
Kit Supply
Voltage Output
Type QD Cables Sensor Cable
Termination
Max. Emitter/Receiver Separation
Blank = 9 m
XL = 18 m
XLHD = Heavy-Duty 18 m
Kit
K = Kit
Quick-Disconnect Cables
C1 = 2 x 5 m
C2 = 2 x 8 m
C3 = 1 x 5 m plus 1 x 8 m
Defi ned
Area
Sensor Finish
Blank = Black anodized
Y = Yellow polyester paint
Supply Voltage
A = 115V ac
B = 230V ac
T = 24V dc
Options
E = With External Device Monitoring (EDM)
Blank = Without
A
Options
24
Beams
Per Foot
3C2
Finish
Beams per Foot
24 = Standard & Long-Range Series
12 = Heavy-Duty Series
Output Type
Blank = Trip
L = Latch
S = Trip/Latch Selectable
Output Configuration
Blank= 2 NO Safety Outputs
3 = 2 NO Safety Outputs &
1 NC Aux.
Sensor Cable Termination
Blank = Integral QD connector
P = Pigtail QD
Output
Confi guration
MS
MSKT24243C2 •
610 mm
19 mm
24
9 m
24V dc
Trip
2 NO
Safety
Outputs
&
1 NC Aux.
8 m,
2 each
MSKT24243C2Y •
MSXLKT24243C2 •25 mm 18 m
MSXLKT24243C2Y •
MSXLHDKT24123C2Y •38 mm 12 18 m
MSKA24243C2 •19 mm
24
9 m
115V ac
MSKA24243C2Y •
MSXLKA24243C2 •25 mm 18 m
MSXLKA24243C2Y •
MSXLHDKA24123C2Y •38 mm 12 18 m
MSKB24243C2 •19 mm
24
9 m
230V ac
MSKB24243C2Y •
MSXLKB24243C2 •25 mm 18 m
MSXLKB24243C2Y •
MSXLHDKB24123C2Y •38 mm 12 18 m
Kit Model Number
Sensor
Housing
Defined
Area
Resolution
Beams Per
Foot
Range
Supply
Voltage
Output Type
Number of
Outputs
QD Cabling
Yellow Black
Heavy-
Duty
Yellow
Emitter/Receiver
Separation
XL PY
You can purchase a kit that contains an emitter and receiver of equal length and range; standard mounting
brackets; and a pair of quick-disconnect cables. Detailed information about individual kit components is
as follows.
• Metal Box Controllers – Floating Blanking . . . . . . . . . . . . . . . . . .Page 64
• Emitter and Receivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59-63
• Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
• Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
A partial listing of kits is listed below; see Kit Model Key to order other variations.
Defined Area
4 = 114 mm
8 = 215 mm
12 = 305 mm
16 = 406 mm
20 = 508 mm
24 = 610 mm
28 = 711 mm
32 = 813 mm
36 = 914 mm
40 = 1016 mm
44 = 1118 mm
48 = 1219 mm
NC = Normally Closed Relay, NO = Normally Open Relay
NOTE: Not all combinations are possible. Contact Banner Engineering Corp. for additional information and/or verification of valid kit model number.
68 More information online at bannerengineering.com
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN®
TYPE 2
MINI-SCREEN® Systems
SAFETY LIGHT SCREENS
MINI-SCREEN® Metal Box Kits - Floating & Fixed Blanking
MSK2T24243C2 •
610 mm
19 mm
24
9 m
24V dc
Trip
2 NO
Safety
Outputs
&
1 NC Aux.
8 m,
2 each
MSK2T24243C2Y •
MSXLK2T24243C2 •25 mm 18 m
MSXLK2T24243C2Y •
MSXLHDK2T24123C2Y •38 mm 12 18 m
MSK2D24243C2 •19 mm
24
9 m
115/230V ac
MSK2D24243C2Y •
MSXLK2D24243C2 •25 mm 18 m
MSXLK2D24243C2Y •
MSXLHDK2D24123C2Y •38 mm 12 18 m
Kit Model Number
Sensor
Housing
Defined
Area
Resolution
Beams Per
Foot
Range
Supply
Voltage
Output Type
Number of
Outputs
QD Cabling
Yellow Black
Heavy-
Duty
Yellow
Kit Model Key
Model Style
MS = MINI-SCREEN
Model
Style
24K
Kit Blanking QD Cables Sensor Cable
Termination
Max. Emitter/Receiver Separation
Blank = 9 m
XL = 18 m
XLHD = Heavy-Duty 18 m
Kit
K = Kit
Quick-Disconnect Cables
C1 = 2 x 5 m
C2 = 2 x 8 m
C3 = 1 x 5 m plus 1 x 8 m
Defi ned
Area
Sensor Finish
Blank = Black anodized
Y = Yellow polyester paint
Supply Voltage
D = 115/230V ac
T = 24V dc
Blanking
2 = Floating & Fixed Blanking
2 D
Supply
Voltage
24
Beams
Per Foot
3C2
Finish
Beams per Foot
24 = Standard & Long-Range Series
12 = Heavy-Duty Series
Output Configuration
Blank= 2 NO Safety Outputs
3 = 2 NO Safety Outputs &
1 NC Aux.
Sensor Cable Termination
Blank = Integral QD connector
P = Pigtail QD
Output
Confi guration
MS
Emitter/Receiver
Separation
XL PY
You can purchase a kit that contains an emitter and receiver of equal length and range; standard mounting
brackets; and a pair of quick-disconnect cables. Detailed information about individual kit components is
as follows.
• Metal Box Controllers – Floating & Fixed Blanking . . . . . . . . . . .Page 64
• Emitter and Receivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59-63
• Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
• Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
A partial listing of kits is listed below; see Kit Model Key to order other variations.
Defined Area
4 = 114 mm
8 = 215 mm
12 = 305 mm
16 = 406 mm
20 = 508 mm
24 = 610 mm
28 = 711 mm
32 = 813 mm
36 = 914 mm
40 = 1016 mm
44 = 1118 mm
48 = 1219 mm
NC = Normally Closed Relay, NO = Normally Open Relay
NOTE: Not all combinations are possible. Contact Banner Engineering Corp. for additional information and/or verification of valid kit model number.
69More information online at bannerengineering.com
MINI-SCREEN® Systems
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN
®
TYPE 2
SAFETY LIGHT SCREENS
MINI-SCREEN® Metal Box with Muting Kits - Floating & Fixed Blanking
MSK2CM24243C2 •
610 mm
19 mm
24
9 m
115/230V ac
or
24V dc
Trip
2 NO
Safety
Outputs
&
1 NC Aux.
8 m,
2 each
MSK2CM24243C2Y •
MSXLK2CM24243C2 •25 mm 18 m
MSXLK2CM24243C2Y •
MSXLHDK2CM24123C2Y •38 mm 12 18 m
Kit Model Number
Sensor
Housing
Defined
Area
Resolution
Beams Per
Foot
Range
Supply
Voltage
Output Type
Number of
Outputs
QD Cabling
Yellow Black
Heavy-
Duty
Yellow
Kit Model Key
Model Style
MS = MINI-SCREEN
Model
Style
24K
Kit Blanking QD Cables Sensor Cable
Termination
Max. Emitter/Receiver Separation
Blank = 9 m
XL = 18 m
XLHD = Heavy-Duty 18 m
Kit
K = Kit
Quick-Disconnect Cables
C1 = 2 x 5 m
C2 = 2 x 8 m
C3 = 1 x 5 m plus 1 x 8 m
Defi ned
Area
Sensor Finish
Blank = Black anodized
Y = Yellow polyester paint
Supply Voltage
C = 115/230V ac or 24V dc
2 C
Supply
Voltage Beams
Per Foot
C2
Finish
Beams per Foot
24 = Standard & Long-Range Series
12 = Heavy-Duty Series
Number of Outputs
Blank= 2 NO Safety Outputs
3 = 2 NO Safety Outputs &
1 NC Aux.
Sensor Cable Termination
Blank = Integral QD connector
P = Pigtail QD
No. of
Outputs
MS
Emitter/Receiver
Separation
XL P
Y
M
Muting Output
Type
24
Output Type
Blank = Trip
L = Latch
Muting Function
M = Muting
Blanking
2 = Floating & Fixed Blanking
You can purchase a kit that contains an emitter and receiver of equal length and range; standard mounting
brackets; and a pair of quick-disconnect cables. Detailed information about individual kit components is
as follows.
• Metal Box Controllers with Muting – Floating & Floating Blanking . . . . . . . .Page 65
• Emitter and Receivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59-63
• Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
• Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
A partial listing of kits is listed below; see Kit Model Key to order other variations.
NOTE: Not all combinations are possible. Contact Banner Engineering Corp. for additional information and/or verification of valid kit model number.
NC = Normally Closed Relay, NO = Normally Open Relay
Defined Area
4 = 114 mm
8 = 215 mm
12 = 305 mm
16 = 406 mm
20 = 508 mm
24 = 610 mm
28 = 711 mm
32 = 813 mm
36 = 914 mm
40 = 1016 mm
44 = 1118 mm
48 = 1219 mm
70 More information online at bannerengineering.com
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN®
TYPE 2
MINI-SCREEN® Systems
SAFETY LIGHT SCREENS
MINI-SCREEN® DIN Module Controller Kits - Floating Blanking
MSDKT2424C2 •
610 mm
19 mm
24
9 m
24V dc Trip
2 NO
Safety
Outputs
8 m,
2 each
MSDKT2424C2Y •
MSXLDKT2424C2 •25 mm 18 m
MSXLDKT2424C2Y •
MSXLHDKT2412C2Y •38 mm 12 18 m
Kit Model Number
Sensor
Housing
Defined
Area
Resolution
Beams Per
Foot
Range
Supply
Voltage
Output Type
Number of
Outputs
QD Cabling
Yellow Black
Heavy-
Duty
Yellow
Kit Model Key
Model Style*
MS = MINI-SCREEN
Model
Style*
24
Kit QD Cables Sensor Cable
Termination
Max. Emitter/Receiver Separation
Blank = 9 m
XL = 18 m
XLHD = Heavy-Duty 18 m
Kit
DK = DIN-style
controller Kit
Quick-Disconnect Cables
C1 = 2 x 5 m
C2 = 2 x 8 m
C3 = 1 x 5 m plus 1 x 8 m
Defi ned
Area
Sensor Finish
Blank = Black anodized
Y = Yellow polyester paint
Supply Voltage
T = 24V dc
T
Supply
Voltage
24
Beams
Per Foot
C2
Finish
Beams per Foot
24 = Standard & Long-Range Series
12 = Heavy-Duty Series
Sensor Cable Termination
Blank = Integral QD connector
P = Pigtail QD
Output
Type
MS
Emitter/Receiver
Separation
XL PY
Output Type
Blank = Trip
L = Latch
DK
You can purchase a kit that contains an emitter and receiver of equal length and range; standard mounting
brackets; and a pair of quick-disconnect cables. Detailed information about individual kit components is
as follows.
• DIN Module Controllers – Floating Blanking . . . . . . . . . . . . . . . . .Page 65
• Emitter and Receivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59-63
• Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
• Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
A partial listing of kits is listed below; see Kit Model Key to order other variations.
* Kits are not available for Dual DIN Modules. A controller, two emitter/receiver pairs and the appropriate cables are sold separately (see page 179).
NOTE: Not all combinations are possible. Contact Banner Engineering Corp. for additional information and/or verification of valid kit model number.
NC = Normally Closed Relay, NO = Normally Open Relay
Defined Area
4 = 114 mm
8 = 215 mm
12 = 305 mm
16 = 406 mm
20 = 508 mm
24 = 610 mm
28 = 711 mm
32 = 813 mm
36 = 914 mm
40 = 1016 mm
44 = 1118 mm
48 = 1219 mm
71More information online at bannerengineering.com
MINI-SCREEN® Systems
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN
®
TYPE 2
SAFETY LIGHT SCREENS
MINI-SCREEN® Emitter & Receiver Specifications
Emitter/Receiver Separation 19 mm Resolution Emitters and Receivers: 150 mm to 9 m
25.4 mm Resolution Emitters and Receivers: 150 mm to 18 m
Minimum Object Sensitivity 19 mm Resolution:
19.1 mm floating blanking OFF
31.8 mm 1-beam floating blanking ON
44.5 mm 2-beam floating blanking ON
25.4 mm Resolution:
25.4 mm floating blanking OFF
38.1 mm 1-beam floating blanking ON
50.8 mm 2-beam floating blanking ON
Response Time Less than 48 milliseconds using emitter/receiver with 114 to 406 mm defined area
Less than 60 milliseconds using emitter/receiver with 508 to 813 mm defined area
Less than 72 milliseconds using emitter/receiver with 914 to 1219 mm defined area
Self-Checking Interval 20 milliseconds
Ambient Light Immunity >10,000 lux at 5° angle of incidence
Strobe Light Immunity Totally immune to one Federal Signal Corp. “Fireball” model FB2PST strobe.
Emitter Elements Infrared LEDs; 880 nm peak emission
Status Indicators Emitter: Green LED for power ON
Receiver: Red, yellow and green status indicators with the same functions as those on the left side of
the control box (see individual Control Box Specifications, pages 73-77). Yellow also indicates
alignment. Indicators are visible on three sides of receiver or emitter base.
Emitter and Receiver
Enclosures
Materials: Aluminum extrusion with black anodized or yellow polyester painted finish; acrylic lens cover
Mounting hardware supplied
Rating: NEMA 4, 13; IEC IP65
Mounting Hardware Emitter and receiver are each supplied with a pair of mounting brackets. Mounting brackets are 11-gauge cold-
rolled black zinc chromate finished steel. A set of four vibration dampening mounts is also supplied.
Cables Emitters and Receivers with Pigtail (MSE/MSRxxxxYP) Quick Disconnect:
Pigtail QD connectors have a 305 mm long cable, terminated with a 5-pin Mini-style quick-disconnect fitting.
Mating interconnect cables are ordered separately (unless a MINI-SCREEN kit is ordered, see Models and
Accessories, page 179), and are available in lengths of 4.5 m, 7.6 m, 15 m, 30 m and 45 m.
NOTE: Contact factory when cable length exceeding 53 m is required. Use only Banner cables, which
incorporate a shielded “twisted pair” for noise immunity on RS485 data communications lines. Use of
other cables may result in “nuisance” trips or lockouts.
Optical Performance This system meets ± 2.5° requirements of IEC 61496-2, section 5.2.9 (Type 4)
Operating Conditions Temperature: 0° to +50° C Relative humidity: 95% maximum (non-condensing)
Certifications For a list of certifications see page 236.
72 More information online at bannerengineering.com
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN®
TYPE 2
MINI-SCREEN® Systems
SAFETY LIGHT SCREENS
MINI-SCREEN® Heavy-Duty Emitter & Receiver Specifications
Emitter/Receiver Separation 150 mm to 18 m
Minimum Object Sensitivity 38 mm floating blanking OFF
62 mm 1-beam floating blanking ON
89 mm 2-beam floating blanking ON
Response Time Less than 48 milliseconds for 610 mm and 813 mm emitter/receiver
Less than 60 milliseconds for 1016 mm to 1626 mm emitter/receiver
Less than 72 milliseconds for 1829 mm emitter/receiver
Self-Checking Interval 20 milliseconds
Ambient Light Immunity >10,000 lux at 5° angle of incidence
Strobe Light Immunity Totally immune to one Federal Signal Corp. “Fireball” model FB2PST strobe.
Emitter Elements Infrared LEDs; 880 nm peak emission
Status Indicators Emitter: Green LED for power ON
Receiver: Red, yellow and green status indicators with the same functions as those on the left side of
the control box (see individual Control Box Specifications, pages 73-77). Yellow also indicates
alignment. Indicators are visible on three sides of receiver or emitter base.
Emitter and Receiver
Enclosures
Materials: Aluminum extrusion with yellow polyester painted finish; acrylic lens cover. Mounting hardware
supplied.
Rating: NEMA 4, 13; IEC IP65
Mounting Hardware Emitter and receiver are each supplied with a pair of mounting brackets. Mounting brackets are 8-gauge cold-
rolled black zinc chromate finished steel.
Cables Emitters and Receivers with Pigtail (MSXLHDE/MSXLHDRxxxxYP) Quick Disconnect:
Pigtail QD connectors have a 305 mm long cable, terminated with a 5-pin Mini-style quick-disconnect fitting.
Mating interconnect cables are ordered separately (unless a MINI-SCREEN kit is ordered, see Models and
Accessories, page 179), and are available in lengths of 4.5 m, 7.6 m, 15 m, 30 m and 45 m.
NOTE: Contact factory when cable length exceeding 53 m is required. Use only Banner cables, which
incorporate a shielded “twisted pair” for noise immunity on RS485 data communications lines. Use of
other cables may result in “nuisance” trips or lockouts.
Optical Performance This system meets ± 2.5° requirements of IEC 61496-2, section 5.2.9 (Type 4)
Operating Conditions Temperature: 0° to +50° C Relative humidity: 95% maximum (non-condensing)
Certifications For a list of certifications see page 236.
73More information online at bannerengineering.com
MINI-SCREEN® Systems
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN
®
TYPE 2
SAFETY LIGHT SCREENS
MINI-SCREEN® Metal Box Controller Specifications
System Power Requirements MSCA-.. models: 115V ac ± 15% (50/60 Hz), 55 VA
MSCB-.. models: 230V ac ± 15% (50/60 Hz), 55 VA
MSCT-.. models: 24V dc ±15%, 10% max. ripple, 1.5 amps max.
MSCD-.. models: 115/230V ac ±15% (50/60 Hz), 55 VA
Fuse Rating MSCA-1.. models: ½ amp, 250V (3 AG or 5x20 mm slow blow)
MSCB-1.. models: ¼ amp, 250V (3 AG or 5x20 mm slow blow)
MSCT-1.. models: 2 amp, 250V (3 AG or 5x20 mm slow blow)
MSCD-2.. models: 115V ac: 1 amp, 250V; 230V ac: 1/2 amp, 250V
MSCT-2.. models: 2 amp, 250V (all fuses 3 AG or 5x20 mm slow blow)
Response Time Standard and Long-Range Emitters/Receivers:
Less than 48 milliseconds using emitter/receiver with 114 mm to 406 mm defined area
Less than 60 milliseconds using emitter/receiver with 508 mm to 813 mm defined area
Less than 72 milliseconds using emitter/receiver with 914 mm to 1219 mm defined area
Heavy-Duty Emitters/Receivers:
Less than 48 milliseconds using emitter/receiver with 610 mm to 813 mm defined area
Less than 60 milliseconds using emitter/receiver with 1016 mm to 1626 mm defined area
Less than 72 milliseconds using emitter/receiver with 1829 mm defined area
Status Indicators
(on control box and receiver)
Solid LED Flashing LED
Red BLOCKED/LATCHED LOCKOUT
Green CLEAR BLANKING ON
Yellow RESET Double Flash = Waiting for Power-up Key Reset
Single Flash = ALIGNMENT. Flash rate increases with the number of
sensing beams “made”, solid yellow when aligned and
defined area is clear
Diagnostic Indicators MSCT-2.. & MSCD-2..:
Two-digit numeric display indicates cause of lockout condition.
Display is visible through a window in the control box cover.
MSCA-1.., MSCB-1.. & MSCT-1..:
Four LEDs indicate cause of lockout condition.
Diagnostic LEDs are visible through a window in the control box cover.
Controls and Adjustments Keyed Reset of system lockout or latched conditions
Floating Blanking selection switches and Fixed Blanking programming switches
Auto Power Up On-Off switches
Test Input Terminals must be closed for a minimum of 0.05 seconds in order to guar an tee a test input signal. The switch-
ing device used must be capable of switching 15-50V dc at 20 to 100 mA.
External Device Monitoring
(EDM) Input
Terminals must be closed before controller attempts to reset (close) the FSD outputs after clearing an
interruption of the defined area. The EDM input should open when the FSD outputs close (a clear condition),
but this is not required. The EDM input must be closed within 200 milliseconds of the FSD outputs opening (a
blocked condition) or a lockout condition will occur. The contacts of the monitored device must be capable of
switching 15-50V dc at 20 to 100 mA.
Auxiliary Monitor Relay Reed relay; 125V ac or dc max., 500 mA max. (10 VA max., resistive load)
Safety Outputs Forced-guided contact relay (resistive load).
MSC..-..2: FSD1 & 2, SSD = 250V ac max., 4 amp max.
MSC..-..3: FSD1 & 2, CNC = 250V ac max., 6 amp max.; SSD = 250V ac max., 4 amp max
Mechanical life: 10,000,000 operations (minimum).
Electrical life: 100,000 operations (typical @ 1.0 kVA switching power).
Arc suppression is recommended when switching inductive loads.
Enclosure Material: Welded steel box with black polyester powder paint finish.
Rating: NEMA 13, IEC IP64
Operating Conditions Temperature: 0° to +50° C Relative humidity: 95% maximum (non-condensing)
FMEA Tested Per requirements IEC 61496-1 (type 4)
Application Notes Use of fixed blanking requires sensors with 16 or more light beams. Up to 12 beams or 30% of the total
number of beams in the array may be blanked, whichever is less. Call factory for applications assistance if a
greater number of blanked beams is required.
Certifications For a list of certifications see page 236.
Wiring Diagrams 2 FSDs, 1 SSD and Power Monitoring: WD022 (p. 258)
74 More information online at bannerengineering.com
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN®
TYPE 2
MINI-SCREEN® Systems
SAFETY LIGHT SCREENS
MINI-SCREEN® Metal Box Controller with Muting Specifications
System Power Requirements 115V ac (50/60Hz) ± 15% @ 500 mA (50 VA),
230V ac (50/60Hz) ± 15% @ 250 mA (50 VA), or
24V dc ±15%, 10% max. ripple, @ 2.5 A (60 W)
Fuse Rating 115V ac: 1.0 A @ 250V ac (supplied)
230V ac: 500 mA @ 250V ac
+24V dc: Internal resettable
Response Time Standard and Long-Range Emitters/Receivers:
Less than 58 milliseconds using emitter/receiver with 114 mm to 406 mm defined area
Less than 70 milliseconds using emitter/receiver with 508 mm to 813 mm defined area
Less than 82 milliseconds using emitter/receiver with 914 mm to 1219 mm defined area
Heavy-Duty Emitters/Receivers:
Less than 58 milliseconds using emitter/receiver with 610 mm to 813 mm defined area
Less than 70 milliseconds using emitter/receiver with 1016 mm to 1626 mm defined area
Less than 82 milliseconds using emitter/receiver with 1829 mm defined area
Status Indicators
(on control box and receiver)
Standard models:
Light Screen Indicators (left column of LEDs):
Solid LED Flashing LED
Red BLOCKED/LATCHED LOCKOUT
Green CLEAR BLANKING ON
Yellow RESET Double Flash = Waiting for Light Screen Key Reset at Power-up
Single Flash = ALIGNMENT. Flash rate increases with the number of
sensing beams “made”, solid yellow when aligned and
defined area clear
System Indicators (right column of LEDs):
Solid LED Flashing LED
Red OVERRIDE LOCKOUT
Green OUTPUT ON (Not Applicable)
(FSD1 & FSD2 closed)
Yellow RESET Double Flash = Waiting for System Key Reset at Power-up
(System) Single Flash = Waiting for System Key Reset at latched condition (manual
reset of system after blockage has been removed)
Diagnostic Indicators Light Screen Diagnostic Display (left window) is a two-digit numeric display that indicates the cause
of lockout conditions.
System Diagnostic Display (right window) is a two-digit numeric display that indicates the cause of
lockout conditions and the amount of time, in seconds, remaining for the backdoor timer.
Controls and Adjustments • Light Screen Key Reset after power-up and light screen lockouts
• Selection switches to enable floating blanking
• Program switches to enable fixed blanking
• Light Screen and System Auto Power-up selection switches
• System Key Reset after power-up, system lockouts, and latched conditions
• Selection switches for Monitored or Non-Monitored Muting Indicator
• Selection switches for One-Way or Two-Way (directional/non-directional) Muting
• Selection switches for One-Channel, Two-Channel Monitoring or No Monitoring (EDM)
• Selection switches for Backdoor Timer settings and Mute-on-Power-Up
Light Screen and
System Reset Inputs
Terminals must be closed for a minimum of 0.05 seconds in order to guarantee a reset. The
switching device must be capable of switching 15-50V dc at 20-100 mA.
External Device Monitoring
(EDM) Input(s)
Two pairs of terminals are provided to monitor the state of external devices that are being controlled
by the FSD outputs. The device must be capable of switching 15-50V dc at 20-100 mA.
Mute Enable Input Terminals must be closed in order to start a mute; opening this input after mute has begun has no
effect. The switching device must be capable of switching 15-50V dc at 20-100 mA.
Override Inputs The two-channel inputs must be closed within 3 seconds of each other (simultaneity requirement)
and held closed during the 10-second Override. To initiate a subsequent Override, open both
channels, wait 3 seconds, and then re-close both channels (within 3 seconds). The switching devices
must be capable of switching 15-50V dc at 20-100 mA.
Muting Device Input The muting devices work in pairs (M1 and M2, M3 and M4) and are required to be “closed” within 3
seconds of each other (simultaneity requirement) to initiate a mute (assuming all other conditions are
met). Each muting device must be capable of switching 15-50V dc at 20-100 mA.
Light Screen and System
Aux. Monitor Relay Outputs
Reed relay; 125V ac/dc max. at 500 mA max. (10 VA maximum, resistive load)
75More information online at bannerengineering.com
MINI-SCREEN® Systems
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN
®
TYPE 2
SAFETY LIGHT SCREENS
MINI-SCREEN® Metal Box Controller with Muting Specifications
CNC Aux. Monitor
Relay Outputs
(Model MSCC-2T3M/-2L3M)
Forced-guided contact relay, 250V ac at 6 amps max. (resistive load)
Safety Outputs Forced-guided contact relay (resistive load).
MSCC-..2: FSD1 & 2, SSD = 250V ac max., 4 amp max.
MSCC-..3: FSD1 & 2, CNC = 250V ac max., 6 amp max.;
SSD = 250V ac max., 4 amp max.
Mechanical life: 10,000,000 operations (minimum).
Electrical life: 100,000 operations (typical @ 1.0 kVA switching power).
Arc suppression is recommended when switching inductive loads.
Mute Lamp Output A monitored or non-monitored (selectable) sinking output. If monitoring has been selected, the
current draw must be within 10 mA to 360 mA.
Max. switching voltage: 30V dc
Max. switching current: 360 mA
Min. switching current: 10 mA
Saturation voltage: ≤ 1.5V dc
Auxiliary DC Supply Output 24V dc ± 25%, 500 mA max
Enclosure Material: Welded steel box with black polyester powder paint finish.
Rating: NEMA 13; IEC IP64
Operating Conditions Temperature: 0° to +50° C Relative humidity: 95% max. (non-condensing)
FMEA Tested Per requirements IEC 61496-1 (Type 4)
Application Notes Use of fixed blanking requires sensors with 16 or more light beams. Up to 12 beams or 30% of the total
number of beams in the array may be blanked, whichever is less. Call factory for applications assistance if a
greater number of blanked beams is required.
Certifications For a list of certifications see page 236.
Wiring Diagrams 2 FSDs, 1 SSD and 2-Channel EDM: WD023 (p. 258)
MINI-SCREEN® Metal Controller Box with Muting Specifications (cont’d)
76 More information online at bannerengineering.com
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN®
TYPE 2
MINI-SCREEN® Systems
SAFETY LIGHT SCREENS
MINI-SCREEN® DIN Module Controller Specifications
System Power Requirements 24V dc ±15%, 10% max. ripple, 1.5 amps. max.
Fuse Rating 2 amp, 250V (3 AG or 5x20 mm slow blow)
Response Time Standard Emitters/Receivers:
Less than 48 milliseconds using emitter/receiver with 114 mm to 406 mm defined area
Less than 60 milliseconds using emitter/receiver with 508 mm to 813 mm defined area
Less than 72 milliseconds using emitter/receiver with 914 mm to 1219 mm defined area
Heavy-Duty Emitters/Receivers:
Less than 48 milliseconds using emitter/receiver with 610 mm to 813 mm defined area
Less than 60 milliseconds using emitter/receiver with 1016 mm to 1626 mm defined area
Less than 72 milliseconds using emitter/receiver with 1829 mm defined area
Status Indicators
(on control box and receiver)
Solid LED Flashing LED
Red BLOCKED/LATCHED LOCKOUT
Green CLEAR BLANKING ON
Yellow RESET Double Flash = Waiting for Power-up Key Reset
Single Flash = ALIGNMENT. Flash rate increases with the number of
sensing beams “made”, solid yellow when aligned and
defined area is clear
Diagnostic Indicators Four LEDs indicate cause of lockout conditions.
Diagnostic LEDs are visible through a window in the control module cover.
Controls and Adjustments Keyed Reset of system lockout and latched conditions
Blanking selection switches
Auto Power Up On-Off switches
Auxiliary Monitor or
Alarm Relay
Reed relay; 125V ac or dc max., 500 mA max. (10 VA max., resistive load)
Safety Outputs Forced-guided contact relays (resistive load)
FSD1 & 2, SSD = 250V ac max., 4 amps max.
Mechanical life: 10,000,000 operations (minimum)
Electrical life: 100,000 operations (typical @ 1.0 kVA switching power)
Arc suppression is recommended when switching inductive loads.
Enclosure Material: polycarbonate
Rating: NEMA 1; IEC IP20
Operating Conditions Temperature: 0° to +50° C Relative humidity: 95% maximum (non-condensing)
FMEA Tested Per requirements of proposed first edition of IEC 61496-1 (Type 4)
Certifications For a list of certifications see page 236.
Wiring Diagrams 2 FSDs, 1 SSD and Power Monitoring: WD024 (p. 259)
77More information online at bannerengineering.com
MINI-SCREEN® Systems
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN
®
TYPE 2
SAFETY LIGHT SCREENS
MINI-SCREEN® Dual DIN Module Controller Specifications
System Power Requirements 24V dc ±15%, 10% max. ripple, 2.5 amps max.
Fuse Rating 2 amp, 250V (3 AG or 5x20 mm slow blow)
Response Time Standard and Long-Range Emitters/Receivers:
Less than 48 milliseconds using emitter/receiver with 114 mm to 406 mm defined area
Less than 60 milliseconds using emitter/receiver with 508 mm to 813 mm defined area
Less than 72 milliseconds using emitter/receiver with 914 mm to 1219 mm defined area
Heavy-Duty Emitters/Receivers:
Less than 48 milliseconds using emitter/receiver with 610 mm to 813 mm defined area
Less than 60 milliseconds using emitter/receiver with 1016 mm to 1626 mm defined area
Less than 72 milliseconds using emitter/receiver with 1829 mm defined area
E-Stop: Less than 15 milliseconds
Status Indicators
(on control box and receiver)
Solid LED Flashing LED
Red BLOCKED/LATCHED LOCKOUT
Green CLEAR BLANKING ON
Yellow RESET Double Flash = Waiting for Power-up Key Reset
Single Flash = ALIGNMENT. Flash rate increases with the number of
sensing beams “made”, solid yellow when aligned and
defined area is clear
Diagnostic Indicator Single-digit alphanumeric display indicates cause of lockout condition.
Controls and Adjustments Keyed Reset of system lockout and latched conditions
Blanking selection switches
Auto Power Up On-Off switches
E-Stop Switch Input Emergency stop switch must offer two normally closed contacts and be capable of switching 50 mA @ 30V dc.
Simultaneity less than 100 milliseconds. Total resistance, including wiring and all switches, must not exceed 30Ω
for proper operation. Functional stop category 0 per NFPA 79 and EN 418, Safety Category 4 per EN 954-1.
Auxiliary Monitor Relay (x2) Reed relay; 125V ac or dc max., 500 mA max. (10 VA max., resistive load)
Safety Outputs Forced-guided contact relays (resistive load)
FSD1 & 2, SSD = 250V ac max., 4 amps max.
Mechanical life: 10,000,000 operations (minimum)
Electrical life: 100,000 operations (typical @ 1.0 kVA switching power)
Arc suppression is recommended when switching inductive loads.
Enclosure Material: Polycarbonate
Rating: NEMA 1; IEC IP20
Operating Conditions Temperature: 0° to +50° C Relative humidity: 95% maximum (non-condensing)
FMEA Tested Per requirements of proposed first edition of IEC 61496-1 (Type 4)
Certifications For a list of certifications see page 236.
Wiring Diagrams 2 FSDs, 1 SSD and Power Monitoring: WD025 (p. 259)
78 More information online at bannerengineering.com
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN®
TYPE 2
EZ-SCREEN® TYPE 2 Systems
SAFETY LIGHT SCREENS
BRACKETS
PAGE 190
QD CABLES
PAGE 176
-)22/23
PAGE
204
34!.$3
PAGE
209
,%.33()%,$3
PAGE
213
8-Pin Euro
).$)#!4/23
PAGE 187
EZ-SCREEN®
Type 2 Light Screens
• A low-cost solution is suited to lower-risk
applications where the result of an accident is
only a slight injury such as a bump, bruise,
knockdown or trapping (but not crushing),
minor cuts and abrasions.
• Simple two-piece system requires no
control box.
• 30 mm resolution detects narrow objects,
such as a hand or ankle across long spans
up to 15 m.
• System meets all requirements for Type 2
applications per IEC61496-1/-2 and Category
2 per EN 954-1.
• System performs internal self-tests, with
typical installations requiring additional
external safety function checks.
• Dedicated models eliminate selectable
functions, DIP switches and programming.
• Trip output model automatically resets when
the beam is cleared; Latch output model
requires a manual reset.
• Fast response times of 11 to 25 milliseconds
shutdown machinery quickly.
See page 180.
Effortless diagnostics.
Intuitive EZ-SCREEN Type 2 status LEDs
indicate
• Power ON
• Fault (flashing LED)
• Beam alignment, top and bottom
• Beam/output status: blocked or clear
Trip
Receiver
Latch
Receiver Emitter
Choosing Type 2 vs. Type 4
The international standard IEC 61496 specifi es requirements for
the design, construction and testing for two levels or “types” of light
screens to ensure the appropriate safety-related performance.
Light Screen Type 2 Type 4
Cost/features
• Lower cost
• Single microprocessor
• Two safety outputs
• Two microprocessors
• Two safety outputs
• Control reliable/Category 4
• More features and range
Functionality
• Faults detected by self-test or
periodic external test
• Fault exclusion increases the
integrity of the safety function
• Faults detected by self-test
• High levels of fault tolerance
through redundancy and
monitoring
Effective
Aperture
Angle (EAA)
• Larger ±5.0° EAA (fi eld-of-view)
• More susceptible to optical
short circuits
• Smaller ±2.5° EAA (fi eld-of-view)
• Less susceptible to optical
short circuits
Applications
• Low- to moderate-risk
applications where injury is slight
• Automated production
equipment, “table-top” robotic
work cells, “pick and place”
machines, small packaging
machines, equipment protection
and supplemental safeguarding
• High-risk applications that can
result in severe injury or death
• Primary safeguard in hazardous
situations
• Injuries that result in an OSHA
recordable incident
• Where mandated by a relevant
standard
Assessing
Risk
Conduct a risk assessment of your machine. Level of risk depends on
the severity of harm and probability of occurrence. In the USA, if severity
of harm is high, regardless of probability, you must choose a Type 4
safety light screen. See ISO 14121, ANSI B11 TR3, and ANSI/RIA
R15.06 for more specifi c information.
Q&A: Type 2 vs Type 4
79More information online at bannerengineering.com
EZ-SCREEN® TYPE 2 Systems
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN
®
TYPE 2
SAFETY LIGHT SCREENS
EZ-SCREEN® Type 2 Systems
EZ-SCREEN Type 2
31.8 mm
L
25.2 mm
Full View
Detailed
Dimensions
EZ-SCREEN® Type 2 Systems, 30 mm Resolution
Model Number Resolution Output Range
Defined
Area
Housing
Length (L)
Supply
Voltage
Safety
Outputs
Response
Time
Connec-
tion
Data
Sheet
LS2TP30-150Q88†
30 mm Resolution
Trip
15 m
150 mm 215 mm
24V dc 2 PNP
OSSD
≤ 11 ms
8-pin
Euro QD 122452
LS2E30-150Q8
LS2TR30-150Q8
LS2LP30-150Q88†
Latch
LS2E30-150Q8
LS2LR30-150Q8
LS2TP30-300Q88†
Trip
300 mm 365 mm ≤ 13 ms
LS2E30-300Q8
LS2TR30-300Q8
LS2LP30-300Q88†
LatchLS2E30-300Q8
LS2LR30-300Q8
LS2TP30-450Q88†
Trip
450 mm 515 mm ≤ 14 ms
LS2E30-450Q8
LS2TR30-450Q8
LS2LP30-450Q88†
LatchLS2E30-450Q8
LS2LR30-450Q8
Download
PDF
30 mm Resolution
† A pair includes an emitter and receiver (example, LS2TP30-150Q88). Emitters (example, LS2E30-150Q8) and receivers (example, LS2TR30-150Q8) are sold separately.
Yellow Painted Aluminum
Economical, compact optical
safeguarding
Type 2 per IEC 61496-1/-2
30 mm resolution and 15 m range
24V dc supply voltage
Latch or trip output
8-pin Euro QD connection
QD cables ordered separately
(see page 176)
IEC IP65 housing
80 More information online at bannerengineering.com
EZ-SCREEN® TYPE 2 Systems
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN®
TYPE 2
SAFETY LIGHT SCREENS
EZ-SCREEN® Type 2 Systems, 30 mm Resolution
Model Number Resolution Output Range
Defined
Area
Housing
Length (L)
Supply
Voltage
Safety
Outputs
Response
Time
Connec-
tion
Data
Sheet
LS2TP30-600Q88†
30 mm Resolution
Trip
15 m
600 mm 665 mm
24V dc 2 PNP
OSSD
≤ 16 ms
8-pin
Euro QD 122452
LS2E30-600Q8
LS2TR30-600Q8
LS2LP30-600Q88†
LatchLS2E30-600Q8
LS2LR30-600Q8
LS2TP30-750Q88†
Trip
750 mm 815 mm ≤ 17 ms
LS2E30-750Q8
LS2TR30-750Q8
LS2LP30-750Q88†
LatchLS2E30-750Q8
LS2LR30-750Q8
LS2TP30-900Q88†
Trip
900 mm 964 mm ≤ 19 ms
LS2E30-900Q8
LS2TR30-900Q8
LS2LP30-900Q88†
LatchLS2E30-900Q8
LS2LR30-900Q8
LS2TP30-1050Q88†
Trip
1050 mm 1114 mm ≤ 21 ms
LS2E30-1050Q8
LS2TR30-1050Q8
LS2LP30-1050Q88†
LatchLS2E30-1050Q8
LS2LR30-1050Q8
LS2TP30-1200Q88†
Trip
1200 mm 1264 mm ≤ 22 ms
LS2E30-1200Q8
LS2TR30-1200Q8
LS2LP30-1200Q88†
LatchLS2E30-1200Q8
LS2LR30-1200Q8
LS2TP30-1350Q88†
Trip
1350 mm 1414 mm ≤ 24 ms
LS2E30-1350Q8
LS2TR30-1350Q8
LS2LP30-1350Q88†
LatchLS2E30-1350Q8
LS2LR30-1350Q8
(cont’d)
Download
PDF
30 mm Resolution
† A pair includes an emitter and receiver (example, LS2TP30-600Q88). Emitters (example, LS2E30-600Q8) and receivers (example, LS2TR30-600Q8) are sold separately.
81More information online at bannerengineering.com
EZ-SCREEN® TYPE 2 Systems
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN
®
TYPE 2
SAFETY LIGHT SCREENS
EZ-SCREEN® Type 2 Systems, 30 mm Resolution
Model Number Resolution Output Range
Defined
Area
Housing
Length (L)
Supply
Voltage
Safety
Outputs
Response
Time
Connec-
tion
Data
Sheet
LS2TP30-1500Q88†
30 mm Resolution
Trip
15 m 1500 mm 1563 mm 24V dc 2 PNP
OSSD ≤ 25 ms 8-pin
Euro QD 122452
LS2E30-1500Q8
LS2TR30-1500Q8
LS2LP30-1500Q88†
Latch
LS2E30-1500Q8
LS2LR30-1500Q8
(cont’d)
Download
PDF
30 mm Resolution
† A pair includes an emitter and receiver (example, LS2TP30-1500Q88). Emitters (example, LS2E30-1500Q8) and receivers (example, LS2TR30-1500Q8) are sold separately.
82 More information online at bannerengineering.com
EZ-SCREEN® TYPE 2 Systems
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN®
TYPE 2
SAFETY LIGHT SCREENS
Download
PDF
EZ-SCREEN® Type 2 Interfacing Products
Models Description
Product
Information
Data
Sheet
Interface Modules
IM-T-9A (3 NO)
• Interface modules provide two or three
normally open force-guided relay outputs rated
at 6 A.
• EZ-SCREEN monitors these interface modules
when they are connected to the EZ-SCREEN
External Device Monitoring (EDM) inputs.
• Convenient plug-in terminal blocks on a 22.5 mm
DIN-rail mountable housing are included.
Page 132 62822
IM-T-11A (2 NO/1 NC)
Muting Modules
MM2-TA-12B • The Muting Module temporarily inhibits a
safety light screen so materials can safely
pass through the screen without stopping the
machinery.
• The module uses redundant microcontroller-
based logic.
Page 123
63517
MMD-TA-12B
116390
MMD-TA-11B
Contactor Products
Mechanically
Linked Contactors • Pairs of contactors create safety stop circuits
with two normally open contacts in series.
• EZ-SCREEN can monitor the circuit because of
the contacts’ force-guided mechanically linked
design.
• Contactors add 10 or 16 amp current carrying
capability to any safety system.
• Auxiliary contacts add 3 or 4 normally open
contacts.
• Suppressors extend the life of an actuating
device that uses a contactor.
• Modular design simplifies assembly and
installation.
Page 186 111881
11-BG00-31-D-024
11-BF16C01-024
Aux. Contacts
11-BGX10-40
11-G484-30
Suppressors
11-BGX77-048
11-G318-48
83More information online at bannerengineering.com
EZ-SCREEN® TYPE 2 Systems
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN
®
TYPE 2
SAFETY LIGHT SCREENS
LS2TK30-600Q88-1RE25 600 mm
30 mm 18 m 24V dc 2 OSSD
Trip
Integral
Euro QD
IM-T-9A,
1 each
8 m,
2 each
LS2LK30-600Q88-1RE25 Latch
LS2TK30-750Q88-1RE25 750 mm Trip
LS2LK30-750Q88-1RE25 Latch
EZ-SCREEN® Type 2 Kits
Model Style
LS2T = Type 2 Light
Screen (Trip)
LS2L = Type 2 Light
Screen (Latch)
Model Style Kit Protected
Height QD Options Interfacing
Options QD Cabling
Length Options
Resolution
30 = 30 mm
Kit
K = Kit
Receiver & Emitter QD Options
Q88 = Receiver with integral 8-pin Euro-style QD
Emitter with integral 8-pin Euro-style QD
QD Cabling Length Options
RE15 = 5 m, 2 each
RE25 = 8 m, 2 each
R15E25 = 5 m (Receiver) & 8 m (Emitter)
R25E15 = 8 m (Receiver) & 5 m (Emitter)
RE50 = 15 m, 2 each
R15E50 = 5 m (Receiver) & 15 m (Emitter)
R50E15 = 15 m (Receiver) & 5 m (Emitter)
R25E50 = 8 m (Receiver) & 15 m (Emitter)
R50E25 = 15 m (Receiver) & 8 m (Emitter)
RE75 = 23 m, 2 each
RE100 = 30 m, 2 each
Kit Model Key
Resolution
30K 1 RE25600 Q88
NOTE: Not all combinations are possible. Contact Banner Engineering Corp. for additional information and/or verification of valid kit model number.
LS2T
Interfacing Options
1 = IM-T-9A Interface Module, 1 each
2 = IM-T-11A Interface Module, 1 each
3 = 11-BG00-31-D-024 Contactors (10A), 2 each
4 = 11-BF16C01-024 Contactors (16A), 2 each
Protected Height
150 mm
300 mm
450 mm
600 mm
750 mm
900 mm
1050 mm
1200 mm
1350 mm
1500 mm
Kit Model Number
Protected
Height
Resolution
Range
Supply
Voltage
No. of
Outputs
Output
Type
Emitter &
Receiver
Connection
Interfacing
Options
QD Cabling
You can purchase a kit that contains an emitter and receiver of equal length; brackets; and optional
interfacing solution and quick-disconnect cables. Detailed information about individual kit components is
as follows.
• Emitter and Receivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 79
• Interfacing Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
• Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
• Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
A partial listing of kits is listed below; see Kit Model Key to order other variations.
84 More information online at bannerengineering.com
EZ-SCREEN® TYPE 2 Systems
EZ-SCREEN®
PICO-GUARD™
MICRO-SCREEN®
MINI-SCREEN®
SAFETY
LIGHT SCREENS
EZ-SCREEN®
TYPE 2
SAFETY LIGHT SCREENS
EZ-SCREEN® Type 2 Specifications
Supply Voltage at the Device* 24V dc ±20% (PELV)
Supply Current* Emitter: 50 mA max.
Receiver: 90 mA max., exclusive of OSSD1 and OSSD2 loads (up to an additional 0.5A each)
Wavelength of Emitter
Elements
Infrared LEDs, 950 nm at peak emission
Short Circuit Protection All inputs and outputs are protected from short circuits to +24V dc or dc common*
Electrical Safety Class III (per IEC 61140: 1997)
Safety Rating Type 2 per IEC 61496-1, -2; Category 2 per EN 954-1
Operating Range 0.2 m to 15 m
Range decreases with use of mirrors and/or lens shields:
Lens shields – approximately 10% less range per shield.
Glass-surface mirrors – approximately 8% less range per mirror.
See Accessory section for more information on a specific mirror, page 204.
Effective Aperture Angle (EAA) Meets Type 2 requirements per IEC 61496-2; ± 5° @ 3 m
Ambient Light Immunity > 10,000 lux at 5° angle of incidence
Strobe Light Immunity Immune as per IEC 61496-2
Response Time Dependent on number of beams; see Models table on page 79.
EDM Input “Power Monitoring” accomplished via Reset/Remote Test input
Reset Input / Remote Test
Input
Connect to +24V dc via a normally closed (NC) reset switch
Auto Rest (Trip Output) Models: Test /Reset
Manual Rest (Latch Output) Models: Test/Restart/Reset
Safety Outputs Two redundant solid-state 24V dc, 0.5 A max. sourcing OSSD (Output Signal Switching Device) safety outputs.
(Use optional interface modules for ac or larger dc loads.)
Not compatible with the Banner “Safety Handshake.”
ON-State voltage: > Vin-1.5V dc
OFF-State voltage: 0.2V dc max.
Max. load capacitance: 0.1 µF
Min. load resistance: 48 Ω
Open ground leakage current: 0.65 mA max.
OSSD test pulse width: 0.25 milliseconds
OSSD test pulse period: 500 milliseconds
Enclosure Materials: Extruded aluminum housing with yellow polyester powder finish and well-sealed, rugged die-cast
zinc end caps, acrylic lens cover
Rating: IEC IP65
Operating Conditions Temperature: 0° to +55° C Relative humidity: 95% maximum (non-condensing)
Shock and Vibration EZ-SCREEN Type 2 systems have passed vibration and shock tests according to IEC 61496-1. This includes
vibration (10 cycles) of 10-55 Hz at 0.35 mm single amplitude (0.70 mm peak-to-peak) and shock of 10 g for
16 milliseconds (6,000 cycles).
Certifications For a list of certifications see page 236.
Wiring Diagrams Emitter: WD026 (p. 260)
Receiver with 2 Solid-State OSSDs, 2 FSDs and Power Monitoring: WD027 (p. 260)
Power Monitoring of IM-T-9A Interface Module: WD028 (p. 261)
*The external voltage supply must be capable of buffering brief mains interruptions of 20 milliseconds as specified in IEC/EN 60204-1.
