IL710
IsoLoop is a registered trademark of NVE Corporation.
*U.S. Patent numbers 5,831,426; 6,300,617 and others.
REV. X
NVE Corporation 11409 Valley View Road, Eden Prairie, MN 55344-3617 Phone: ( 952) 829-9217 Fax: (952) 829-9189 www.IsoLoop.com ©NVE Corporation
High Speed/High Temperature Digital Isolators
Functional Diagram
OUT1
VOE
IN1
IL710
Truth Table
VI VOE VO
L L L
H L H
L H Z
H H Z
Features
• +5 V/+3.3 V CMOS / TTL Compatible
• High Speed: 150 Mbps Typical (IL710S)
• High Temperature: −40°C to +125°C (IL710T)
• 1.5 mA/Channel Typical Quiescent Current
• 300 ps Typical Pulse Width Distortion (IL710S)
• 100 ps Typical Pulse Jitter
• 2 ns Channel-to-Channel Skew
• 10 ns Typical Propagation Delay
• Low EMC Footprint
• 30 kV/μs Typical Common Mode Transient Immunity
• 2500 VRMS Isolation (1 min.)
• UL1577 and IEC 61010-2001 Approved
• 8-pin MSOP, SOIC, and PDIP Packages
Applications
•
Digital Fieldbus
•
RS-485 and RS-422
•
Multiplexed Data Transmission
•
Data Interfaces
•
Board-to-Board Communication
•
Digital Noise Reduction
•
Operator Interface
•
Ground Loop Elimination
•
Peripheral Interfaces
•
Serial Communication
•
Logic Level Shifting
Description
N
VE’s IL700 family of high-speed digital isolators are CMOS
devices manufactured with NVE’s patented* IsoLoop® spintronic
Giant Magnetoresistive (GMR) technology. The IL710S is the
world’s fastest isolator of its type, with a 150 Mbps typical data rate.
The symmetric magnetic coupling barrier provides a typical
propagation delay of only 10 ns and a pulse width distortion as low
as 300 ps (0.3 ns), achieving the best specifications of any isolator.
Typical transient immunity of 30 kV/µs is unsurpassed. The IL710 is
ideal for isolating applications such as PROFIBUS, RS-485, and
RS-422.
The IL710 is available in 8-pin MSOP, SOIC, and PDIP packages.
Standard and S-Grade parts are specified over a temperature range of
−40°C to +100°C; T-Grade parts are specified over a temperature
range of −40°C to +125°C.
IL710
2
Absolute Maximum Ratings
Parameters Symbol Min. Typ. Max. Units Test Conditions
Storage Temperature TS −55 150 °C
Ambient Operating Temperature
(
1
)
IL710T TA −55 125
135 °C
Supply Voltage VDD1, VDD2 −0.5 7 V
Input Voltage VI −0.5 VDD1+0.5 V
Input Voltage VOE −0.5 VDD2+0.5 V
Output Voltage VO −0.5 VDD2+0.5 V
Output Current Drive IO 10 mA
Lead Solder Temperature 260 °C 10 sec.
ESD 2 kV HBM
Recommended Operating Conditions
Parameters Symbol Min. Typ. Max. Units Test Conditions
Ambient Operating Temperature
IL710 and IL710S
IL710T
TA
TA
−40
−40
100
125
°C
°C
Supply Voltage VDD1, VDD2 3.0 5.5 V
Logic High Input Voltage VIH 2.4 VDD1 V
Logic Low Input Voltage VIL 0 0.8 V
Input Signal Rise and Fall Times tIR, tIF 1 μs
Insulation Specifications
Parameters Symbol Min. Typ. Max. Units Test Conditions
Creepage Distance
MSOP 3.01 mm
SOIC 4.04 mm
PDIP 7.04 mm
Leakage Current
(
5
)
0.2 μA 240 VRMS, 60 Hz
Barrier Impedance
(
5
)
>1014||3 Ω || pF
Package Characteris tics
Parameters Symbol Min. Typ. Max. Units Test Conditions
Capacitance (Input–Output)
(
5
)
C
I–O 1.1 pF f = 1 MHz
Thermal Resistance
MSOP θJC 168 °C/W
Thermocouple at center
underside of package
SOIC θJC 144 °C/W
PDIP θJC 54 °C/W
Package Power Dissipation PPD 150 mW f = 1 MHz, VDD = 5 V
Safety and Approvals
IEC61010-1
TUV Certificate Numbers: N1502812, N1502812-101
Classification as Reinfor ced Insulation
Model Package
Pollution
Degree Material
Group Max. Working
Voltage
IL710-1 MSOP II III 150 VRMS
IL710-2 PDIP II III 300 VRMS
IL710-3 SOIC II III 150 VRMS
UL 1577
Component Recognition Program File Number: E207481
Rated 2500VRMS for 1 minute
Soldering Profile
Per JEDEC J-STD-020C, MSL=2
IL710
3
IL710 Pin Connections
1 VDD1 Supply voltage
2 IN Data In
3 NC No internal connection
4 GND1 Ground return for VDD1
5 GND2 Ground return for VDD2
6 OUT Data Out
7
VOE Output enable.
Internally held low with 100 kΩ
8 VDD2 Supply voltage
VDD1 VDD2
IN VOE
NC OUT
GND1GND2
IL710
Timing Diagram
Legend
tPLH Propagation Delay, Low to High
tPHL Propagation Delay, High to Low
tPW Minimum Pulse Width
tPLZ Propagation Delay, Low to High Impedance
tPZH Propagation Delay, High Impedance to High
tPHZ Propagation Delay, High to High Impedance
tPZL Propagation Delay, High Impedance to Low
tR Rise Time
tF Fall Time
IL710
4
3.3 Volt Electrical Specifications
Electrical specifications are Tmin to Tmax unless otherwise stated.
Parameters Symbol Min. Typ. Max. Units Test Conditions
DC Specifications
Input Quiescent Supply Current IDD1 8 10
μA
Output Quiescent Supply Current IDD2 1.5 2 mA
Logic Input Current II −10 10 μA
Logic High Output Voltage VOH VDD−0.1 VDD V IO = −20 μA, VI = VIH
0.8 x VDD 0.9 x VDD I
O = −4 mA, VI = VIH
Logic Low Output Voltage VOL 0 0.1
V IO = 20 μA, VI = VIL
0.5 0.8 IO = 4 mA, VI = VIL
Switching Specifications
Maximum Data Rate
IL710 and IL710T
IL710S
100
130
110
140
Mbps
Mbps
CL = 15 pF
CL = 15 pF
Pulse Width
(
7
)
PW 10 7.5 ns 50% Points, VO
Propagation Delay Input to Output
(High to Low) tPHL 12 18 ns CL = 15 pF
Propagation Delay Input to Output
(Low to High) tPLH 12 18 ns CL = 15 pF
Propagation Delay Enable to Output
(High to High Impedance) tPHZ 3 5 ns CL = 15 pF
Propagation Delay Enable to Output
(Low to High Impedance) tPLZ 3 5 ns CL = 15 pF
Propagation Delay Enable to Output
(High Impedance to High) tPZH 3 5 ns CL = 15 pF
Propagation Delay Enable to Output
(High Impedance to Low) tPZL 3 5 ns CL = 15 pF
Pulse Width Distortion
(
2
)
IL710 and IL710T
IL710S
PWD
2
1
3
3
ns
CL = 15 pF
Pulse Jitter
(
8
)
t
J 100 ps CL = 15 pF
Propagation Delay Skew
(
3
)
t
PS
K
4 6 ns CL = 15 pF
Output Rise Time (10%–90%) tR 2 4 ns CL = 15 pF
Output Fall Time (10%–90%) tF 2 4 ns CL = 15 pF
Common Mode Transient Immunity
(Output Logic High or Logic Low)(4) |CMH|,|CML| 20 30 kV/μs VCM = 300 V
Dynamic Power Consumption
(
6
)
140 240 μA/MHz
IL710
5
5 Volt Electrical Specifications
Electrical specifications are Tmin to Tmax unless otherwise stated.
Parameters Symbol Min. Typ. Max. Units Test Conditions
DC Specifications
Input Quiescent Supply Current IDD1 10 15 μA
Output Quiescent Supply Current IDD2 2 3 mA
Logic Input Current II −10 10 μA
Logic High Output Voltage VOH VDD−0.1 VDD V IO = −20 μA, VI = VIH
0.8 x VDD 0.9 x VDD I
O = −4 mA, VI = VIH
Logic Low Output Voltage VOL 0 0.1
V IO = 20
μ
A, VI = VIL
0.5 0.8 IO = 4 mA, VI = VIL
Switching Specifications
Maximum Data Rate
IL710 and IL710T
IL710S
100
130
110
150
Mbps
Mbps
CL = 15 pF
CL = 15 pF
Pulse Width
(
7
)
PW 10 7.5 ns 50% Points, VO
Propagation Delay Input to Output
(High to Low) tPHL 10 15 ns CL = 15 pF
Propagation Delay Input to Output
(Low to High) tPLH 10 15 ns CL = 15 pF
Propagation Delay Enable to Output
(High to High Impedance) tPHZ 3 5 ns CL = 15 pF
Propagation Delay Enable to Output
(Low to High Impedance) tPLZ 3 5 ns CL = 15 pF
Propagation Delay Enable to Output
(High Impedance to High) tPZH 3 5 ns CL = 15 pF
Propagation Delay Enable to Output
(High Impedance to Low) tPZL 3 5 ns CL = 15 pF
Pulse Width Distortion
(
2
)
IL710 and IL710T
IL710S
PWD
2
0.3
3
3
ns
CL = 15 pF
Propagation Delay Skew
(
3
)
t
PS
K
4 6 ns CL = 15 pF
Output Rise Time (10%–90%) tR 1 3 ns CL = 15 pF
Output Fall Time (10%–90%) tF 1 3 ns CL = 15 pF
Common Mode Transient Immunity
(Output Logic High or Logic Low)(4) |CMH|,|CML| 20 30 kV/μs Vcm = 300 V
Dynamic Power Consumption
(
6
)
200 340 μA/MHz
Notes (apply to both 3.3 V and 5 V specifications):
1. Absolute maximum ambient operating temperature means the device will not be damaged if operated under these conditions. It does not
guarantee performance.
2. PWD is defined as |tPHL − tPLH|. %PWD is equal to PWD divided by pulse width.
3. tPSK is the magnitude of the worst-case difference in tPHL and/or tPLH between devices at 25°C.
4. CMH is the maximum common mode voltage slew rate that can be sustained while maintaining VO > 0.8 VDD2. CML is the maximum
common mode input voltage that can be sustained while maintaining VO < 0.8 V. The common mode voltage slew rates apply to both rising
and falling common mode voltage edges.
5. Device is considered a two terminal device: pins 1–4 shorted and pins 5–8 shorted.
6. Dynamic power consumption is calculated per channel and is supplied by the channel’s input side power supply.
7. Minimum pulse width is the minimum value at which specified PWD is guaranteed.
8. 66,535-bit pseudo-random binary signal (PRBS) NRZ bit pattern with no more than five consecutive 1s or 0s; 800 ps transition time.
IL710
6
80 ns
Application Information
Electrostatic Discharge Sensitivity
This product has been tested for electrostatic sensitivity to the
limits stated in the specifications. However, NVE recommends that
all integrated circuits be handled with appropriate care to avoid
damage. Damage caused by inappropriate handling or storage could
range from performance degradation to complete failure.
Electromagnetic Compatibility
IsoLoop Isolators have the lowest EMC footprint of any isolation
technology. IsoLoop Isolators’ Wheatstone bridge configuration
and differential magnetic field signaling ensure excellent EMC
performance against all relevant standards.
These isolators are fully compliant with generic EMC standards
EN50081, EN50082-1 and the umbrella line-voltage standard for
Information Technology Equipment (ITE) EN61000. NVE has
completed compliance tests in the categories below:
EN50081-1
Residential, Commercial & Light Industrial
Methods EN55022, EN55014
EN50082-2: Industrial Environment
Methods EN61000-4-2 (ESD), EN61000-4-3 (Electromagnetic
Field Immunity), EN61000-4-4 (Electrical Transient Immunity),
EN61000-4-6 (RFI Immunity), EN61000-4-8 (Power Frequency
Magnetic Field Immunity), EN61000-4-9 (Pulsed Magnetic
Field), EN61000-4-10 (Damped Oscillatory Magnetic Field)
ENV50204
Radiated Field from Digital Telephones (Immunity Test)
Immunity to external magnetic fields is even higher if the field
direction is “end-to-end” rather than to “pin-to-pin” as shown in the
diagram below:
Cross-axis Field Direction
Dynamic Power Consumption
IsoLoop Isolators achieve their low power consumption from the
way they transmit data across the isolation barrier. By detecting the
edge transitions of the input logic signal and converting these to
narrow current pulses, a magnetic field is created around the GMR
Wheatstone bridge. Depending on the direction of the magnetic
field, the bridge causes the output comparator to switch following
the input logic signal. Since the current pulses are narrow, about
2.5 ns, the power consumption is independent of mark-to-space
ratio and solely dependent on frequency. This has obvious
advantages over optocouplers, which have power consumption
heavily dependent on mark-to-space ratio.
Power Supply Decoupling
Both power supplies to these devices should be decoupled with low
ESR 47 nF ceramic capacitors. Ground planes for both GND1 and
GND2 are highly recommended for data rates above 10 Mbps.
Capacitors must be located as close as possible to the VDD pins.
Signal Status on Start-up and Shut Down
To minimize power dissipation, input signals are differentiated and
then latched on the output side of the isolation barrier to reconstruct
the signal. This could result in an ambiguous output state
depending on power up, shutdown and power loss sequencing.
Therefore, the designer should consider including an initialization
signal in the start-up circuit. Initialization consists of toggling the
input either high then low, or low then high.
Data Transmission Rates
The reliability of a transmission system is directly related to the
accuracy and quality of the transmitted digital information. For a
digital system, those parameters which determine the limits of the
data transmission are pulse width distortion and propagation delay
skew.
Propagation delay is the time taken for the signal to travel through
the device. This is usually different when sending a low-to-high
than when sending a high-to-low signal. This difference, or error, is
called pulse width distortion (PWD) and is usually in nanoseconds.
It may also be expressed as a percentage:
PWD% = Maximum Pulse Width Distortion (ns) x 100%
Signal Pulse Width (ns)
For example, with data rates of 12.5 Mbps:
PWD% = 3 ns x 100% = 3.75%
This figure is almost three times better than an y available
optocoupler with the same temperature range, and two times better
than any optocoupler regardless of published temperature range.
IsoLoop isolators exceed the 10% maximum PWD recommended
by PROFIBUS, and will run to nearly 35 Mb within the 10% limit.
Propagation delay skew is the signal propagation difference
between two or more channels. This becomes significant in clocked
systems because it is undesirable for the clock pulse to arrive
before the data has settled. Short propagation delay skew is
therefore especially critical in high data rate parallel systems for
establishing and maintaining accuracy and repeatability. Worst-
case channel-to-channel skew in an IL700 Isolator is only 3 ns,
which is ten times better than any optocoupler. IL700 Isolators
have a maximum propagation delay skew of 6 ns, which is five
times better than any optocoupler.
IL710
7
Application Diagrams
Isolated PROFIBUS / RS-485
Isolation
Boundary
IL710
IL710
IL710
ISL8485
NVE offers a unique line of PROFIBUS/RS-485 transceivers, but IL710 isolators can also be used as part of multi-chip designs using non-
isolated PROFIBUS transceivers.
Note:
VDD1 and VISO should be decoupled with
10 nF ceramic capacitors at IL710
supply pins.
RS-485 Truth Table
TXD RTS A B RXD
1 0 Z Z X
0 0 Z Z X
1 1 1 0 1
0 1 0 1 0
IL710
8
Isolated USB
+3.3V
NET2890
USPB
USBM
USBOE
ISO_USB+
ISO_USB-
3
4
27
R1
1.5k
Power supplied by USB
bus power this side of
isolation boundary
All power supplied by USB node’s
external supply on this side of
isolation boundary
5 x IL710
Isolation
Boundary
In this circuit, power is supplied by USB bus power on one side of the isolation barrier, and the USB node’s external supply on the other side of
the barrier. IL700 Isolators are specified with just 3 ns worst-case pulse width distortion.
IL710
9
Package Drawings, Dimensions and Specifications
8-pin MSOP
0.114 (2.90)
0.114 (2.90)
0.016 (0.40)
0.005 (0.13)
0.009 (0.23)
0.027 (0.70)
0.010 (0.25)
0.028 (0.70) 0.002 (0.05)
0.043 (1.10)
0.032 (0.80)
0.006 (0.15)
0.016 (0.40)
0.024 (0.60)
0.189 (4.80)
0.197 (5.00)
0.122 (3.10)
0.122 (3.10)
6˚
0˚
Pin spacing is a BASIC
dimension; tolerances
do not accumulate
NOTE:
8-pin SOIC Package
0.013 (0.33)
0.020 (0.50)
0.189 (4.8)
0.197 (5.0)
0.150 (3.8)
0.157 (4.0)
Dimensions in inches (mm)
3
2
1
0.228 (5.8)
0.244 (6.2)
0.008 (0.19)
0.010 (0.25)
0.010 (0.25)
0.020 (0.50)
x45º
0º
8º
0.016 (0.40)
0.050 (1.27)
0.040 (1.0)
0.060 (1.5)
0.054 (1.37)
0.069 (1.75)
0.004 (0.10)
0.010 (0.25)
Pin spacing is a BASIC
dimension; tolerances
do not accumulate
NOTE:
8-pin PDIP
0.36 (9.0)
0.40 (10.2)
Pin spacing is a BASIC
dimension; tolerances
do not accumulate
NOTE:
0.24 (6.1)
0.26 (6.6)
0.29 (6.4)
0.31 (7.9)
0.30 (7.6)
0.37 (9.4)
0.008 (0.2)
0.015 (0.4)
0.030 (0.76)
0.045 (1.14) 0.015 (0.38)
0.023 (0.58) 0.045 (1.14)
0.065 (1.65)
0.09 (2.3)
0.11 (2.8)
0.015 (0.38)
0.035 (0.89)
0.12 (3.05)
0.15 (3.81)
IL710
10
Ordering Information and Valid Part Numbers
IL 710 T - 3 E TR13
Bulk Packaging
Blank = Tube
TR7 = 7" Tape and Reel
TR13 = 13" Tape and Reel
Package
Blank = 80/20 Tin/Lead Plating
E = RoHS Compliant
Package T ype
-1 = MSOP
-2 = PDIP
-3 = 0.15" 8-pin SOIC
Grade
Blank = Standard
T = High Temperature
S = High Speed
Base Part Number
710 = Single Channel
Product Family
IL = Isolators
Valid Part Numbers
IL710-1E
IL710S-1E
IL710T-1E
IL710-2
IL710T-2
IL710-2E
IL710T-2E
IL710-3
IL710S-3
IL710T-3
IL710-3E
IL710S-3E
IL710T-3E
All MSOP and SOIC
parts are available on
tape and reel.
RoHS
COMPLIANT
IL710
11
ISB-DS-001-IL710-X
March 2012 Changes
• Tightened typ. output quiescent supply spec. from 1.7 mA to 1.5 mA.
• T-Series quiescent supply specs. tightened to be the same as other grades.
ISB-DS-001-IL710-W
Changes
• Update terms and conditions.
ISB-DS-001-IL710-V
Changes
• Additional cha nges to MSOP pin spaci ng on packa ge d rawing.
ISB-DS-001-IL710-U
Changes
• Changed MSOP pin spacing on package drawing.
ISB-DS-001-IL710-T Changes
• Added typical jitter specification at 5V.
ISB-DS-001-IL710-S
Changes
• Added EMC details.
ISB-DS-001-IL710-R Changes
• IEC 61010 approval for MSOP version.
ISB-DS-001-IL710-Q
Changes
• Added magnetic immunity to 3.3 and 5 volt electrical specifications.
• Added diagram showing cross-axis direction.
• Added magnetic compatibility to the applications information section.
ISB-DS-001-IL710-P Changes
• Note on all package drawings that p in-spacing tolerances are non-accumulating; change
MSOP pin-spacing dimensions and tolerance accordingly.
ISB-DS-001-IL710-O
Changes
• Corrected PWD spec. on Isolated USB application diagram (p. 8).
• Changed lower limit of length on PDIP package drawing and
tightened pin-spacing tolerance on MSOP package drawing (p. 9).
ISB-DS-001-IL710-N
Changes
• Changed IL710T output quiescent supply current specifications.
ISB-DS-001-IL710-M
Changes
• Changed ordering information to reflect that devices are now fully RoHS compliant with
no exemptions.
ISB-DS-001-IL710-L
Changes
• Eliminated soldering profile chart
ISB-DS-001-IL710-K
Changes
• Edited Profibus application
ISB-DS-001-IL710-J
Changes
• MSOP package, S- and T-Gra des added
• Order information updated
ISB-DS-001-IL710-I Changes
• Added MSOP specifications
• Updated UL and IEC numbers
IL710
12
Datasheet Limitations
The information and data provided in datasheets shall define the specification of the product as agreed between NVE and its customer, unless NVE and
customer have explicitly agreed otherwise in writing. All specifications are based on NVE test protocols. In no event however, shall an agreement be
valid in which the NVE product is deemed to offer functions and qualities beyond those described in the datasheet.
Limited Warranty and Liability
Information in this document is believed to be accurate and reliable. However, NVE does not give any representations or warranties, expressed or
implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information.
In no event shall NVE be liable for any indirect, incidental, punitive, special or consequential damages (including, without limitation, lost profits, lost
savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on
tort (including negligence), warranty, breach of contract or any other legal theory.
Right to Make Changes
NVE reserves the right to make changes to information published in this document including, without limitation, specifications and product descriptions
at any time and without notice. This document supersedes and replaces all information supplied prior to its publication.
Use in Life-Critical or Safety-Critical Applications
Unless NVE and a customer explicitly agree otherwise in writing, NVE products are not designed, authorized or warranted to be suitable for use in life
support, life-critical or safety-critical devices or equipment. NVE accepts no liability for inclusion or use of NVE products in such applications and such
inclusion or use is at the customer’s own risk. Should the customer use NVE products for such application whether authorized by NVE or not, the
customer shall indemnify and hold NVE harmless against all claims and damages.
Applications
Applications described in this datasheet are illustrative only. NVE makes no representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Customers are responsible for the design and operation of their applications and products using NVE products, and NVE accepts no liability for any
assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the NVE product is suitable and fit for
the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customers. Customers should
provide appropriate design and operating safeguards to minimize the risks associated with their applications and products.
NVE does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s
applications or products, or the application or use by customer’s third party customers. The customer is responsible for all necessary testing for the
customer’s applications and products using NVE products in order to avoid a default of the applications and the products or of the application or use by
customer’s third party customers. NVE accepts no liability in this respect.
Limiting Values
Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the
device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the recommended
operating conditions of the datasheet is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the
quality and reliability of the device.
Terms and Conditions of Sale
In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NVE hereby expressly objects to
applying the customer’s general terms and conditions with regard to the purchase of NVE products by customer.
No Offer to Sell or License
Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication
of any license under any copyrights, patents or other industrial or intellectual property rights.
Export Control
This document as well as the items described herein may be subject to export control regulations. Export might require a prior authorization from national
authorities.
Automotive Qualified Products
Unless the datasheet expressly states that a specific NVE product is automotive qualified, the product is not suitable for automotive use. It is neither
qualified nor tested in accordance with automotive testing or application requirements. NVE accepts no liability for inclusion or use of non-automotive
qualified products in automotive equipment or applications.
In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall
use the product without NVE’s warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the
product for automotive applications beyond NVE’s specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies
NVE for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NVE’s
standard warranty and NVE’s product specifications.
IL710
13
An ISO 9001 Certified Company
NVE Corporation
11409 Valley View Road
Eden Prairie, MN 55344-3617 USA
Telephone: (952) 829-9217
Fax: (952) 829-9189
www.nve.com
e-mail: iso-info@nve.com
©NVE Corporation
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.
ISB-DS-001-IL710-X March 2012
