RP30-2412DEW-HC - RECOM Power

Features

Regulated

Converters

• 4:1 Wide Input Voltage Range

• 1.6kVDC Isolation

• UL Certiﬁed

• Efﬁciency up to 88%

• Six-Sided Continuous Shield

• Available as Power Module (RPM30-EW)

PD-1

REV.: 1/2016www.recom-power.com

DC/DC Converter

Description

The RP30-EW series wide input range DC/DC converters are certiﬁed to UL 60950-1 and to cUL 60950-

1. This makes them ideal for all telecom and industrial applications where approved safety standards

are required. The industry standard 2” x 1.6” package meets military standards for thermal shock and

vibration tolerance.

E196683

30 Watt

Single &

Dual

Output

RP30-EW

Selection Guide

Part Number Input Output Output Input(1) Efﬁciency(1) Max. Capacitive

Voltage Range Voltage Current Current typ. Load(2)

[VDC] [VDC] [mA] [mA] [%] [µF]

RP30-243.3SEW(3,4) 10-40 3.3 6000 948 87 19500

RP30-2405SEW(3,4) 10-40 5 6000 1437 87 10200

RP30-2412SEW(3,4) 10-40 12 2500 1437 87 3300

RP30-2415SEW(3,4) 10-40 15 2000 1420 88 1100

RP30-483.3SEW(3,4) 18-75 3.3 6000 474 87 19500

RP30-4805SEW(3,4) 18-75 5 6000 710 88 10200

RP30-4812SEW(3,4) 18-75 12 2500 718 87 3300

RP30-4815SEW(3,4) 18-75 15 2000 710 88 1100

RP30-2412DEW(3,4) 10-40 ±12 ±1250 1488 84 ±1000

RP30-2415DEW(3,4) 10-40 ±15 ±1000 1471 85 ±680

RP30-4812DEW(3,4) 18-75 ±12 ±1250 735 85 ±1000

RP30-4815DEW(3,4) 18-75 ±15 ±1000 726 86 ±680

UL60950-1 Certiﬁed

Model Numbering

Ordering Examples

RP30-2405SEW = 24V Input, 5V Output, Positive Logic CTRL pin.

RP30-4812DEW/N-HC = 48V Input, ±12V Output, Negative Logic CTRL pin, Heat-sink ﬁtted

Input Voltage

Output Voltage

Single or Dual

RP30-__ __ _EW/_ _

Package(4)

Control Logic(3)

Notes:

Note3: no sufﬁx for CTRL function with Positive Logic (1=ON, 0=OFF)

add “N” for CTRL function with Negative Logic (0=ON, 1=OFF)

Note4: add sufﬁx -HC for premounted Heat-sink and clips

Notes:

Note1: Maximum value at nominal input voltage and full load.

Note2: Test by minimum Vin and constant resistor load.

BASIC CHARACTERISTICS

Parameter Condition Min. Typ. Max.

Input Voltage Range nom. Vin = 24V

nom. Vin = 48V

10VDC

18VDC

24VDC

48VDC

40VDC

75VDC

Under Voltage Lockout (UVLO)

Vin = 24V DC-DC ON

DC-DC OFF 8VDC

10VDC

Vin = 48V DC-DC ON

DC-DC OFF 16VDC

18VDC

Input Filter(5) L-C Type

Input Reﬂected Ripple Current(6) nominal Vin and full load 20mAp-p

Input Surge Voltage Vin= 24V, 100ms max.

Vin= 48V, 100ms max.

50VDC

100VDC

Start-up time Power up

Remote ON/OFF

10ms

Operating Frequency Range 270kHz 300kHz 330kHz

Minimum Load % of full load Single

Dual

10%

Ripple and Noise measured by 20Mhz bandwidth

with a 0.1µF/50V MLCC

Others

5Vout

12Vout, 15Vout

60mVp-p

75mVp-p

100mVp-p

Remote ON/OFF(7)

Positive Logic DC-DC ON

DC-DC OFF

Open or 3.0V < Vr < 12V

Short or 0V <Vr < 1.2V

Negative Logic DC-DC ON

DC-DC OFF

Short or 0V <Vr < 1.2V

Open or 3.0V < Vr < 12V

Input current of Remote pin (CTRL) DC-DC OFF 3mA

DC-DC ON -0.5mA 0.5mA

continued on next page

PD-2 REV.: 1/2016 www.recom-power.com

DC/DC Converter

RP30-EW

Series

Speciﬁcations measured at Ta = 25°C, nominal input voltage, full load otherwise noted

Notes:

Note5: An external ﬁlter capacitor is required for normal operation. The capacitor should be capable of handling 1A

ripple current for 48V/24V models.

RECOM suggest: Nippon chemi-con KY series, 220µF/100V, ESR 90m Ω.

Note6: Simulated source impedance of 12µH. 12µH inductor in series with +Vin.

Note7: The ON/OFF control function can be positive or negative logic. The pin voltage is referenced to -Vin pin.

Efﬁciency vs. Output Current Efﬁciency vs. Input Voltage

10Vin

24Vin

40Vin

Efficiency [%]

Output Current [%]

20 40 60 80 10030 50 70 90

Efficiency [%]

Input Voltage [VDC]

16 19 25

37 4013 22 28 34

RP30-2405SE

DC/DC Converter

Speciﬁcations measured at Ta = 25°C, nominal input voltage, full load otherwise noted

REGULATIONS

Parameter Condition Value

Output Voltage Accuracy ±1%

Voltage Adjustability ±10%

Line Voltage Regulation low line to high line at full load ±0.5%

Load Voltage Regulation(8) no load to full load Single

Dual

±0.5%

±1.0%

Cross Regulation asymmetrical 25%<>100% load ±5%

Transient Response recovery time 25% load step change 250µs

continued on next page

RP30-EW

Series

PD-3

REV.: 1/2016www.recom-power.com

Notes:

Note8: The dual output required a minimum 10% loading on the output to maintain speciﬁed

regulation. Operation under no-load condition will not damage these devices, however they

may not meet all listed speciﬁcation.

Efﬁciency vs. Output Current Efﬁciency vs. Input Voltage

18Vin

48Vin

75Vin

Efficiency [%]

Output Current [%]

20 40 60 80 10030 50 70 90

Efficiency [%]

Input Voltage [VDC]

30 36 48 60 757224 42 54 66

RP30-4805SEW

External Output Trimming

Trim up 1 2 3 4 5 6 7 8 9 10 %

Vout = 3.333 3.366 3.399 3.432 3.465 3.498 3.531 3.564 3.597 3.63 Volts

RU = 57.93 26.16 15.58 10.28 7.11 4.99 3.48 2.34 1.46 0.75 KOhms

Trim down 1 2 3 4 5 6 7 8 9 10 %

Vout = 3.267 3.234 3.201 3.168 3.135 3.102 3.069 3.036 3.003 2.97 Volts

RD = 69.47 31.23 18.49 12.12 8.29 5.74 3.92 2.56 1.50 0.65 KOhms

RP30-xx3.3SEW

Output Voltage Trimming

Single output Powerline converters offer the feature of trimming the output voltage over a certain range around the nominal value by using external

trim resistors. No general equation can be given for calculating the trim resistors, but the following trimtables give typical values for chosing these

trimming resistors. If voltages between the given trim points are required, extrapolate between the two nearest given values to work out the resis tor

required or use a variable resistor to set the output voltage. Output can be externally trimmed by using the method shown below.

7(7)

8(8)

6(5)

Trim up Trim down

PD-4 REV.: 1/2016 www.recom-power.com

DC/DC Converter

Speciﬁcations measured at Ta = 25°C, nominal input voltage, full load otherwise noted

RP30-EW

Series

Trim up 1 2 3 4 5 6 7 8 9 10 %

Vout = 5.05 5.10 5.15 5.20 5.25 5.30 5.35 5.4 5.45 5.50 Volts

RU = 36.57 16.58 9.92 6.58 4.59 3.25 2.30 1.59 1.03 0.59 KOhms

Trim down 1 2 3 4 5 6 7 8 9 10 %

Vout = 4.95 4.90 4.85 4.80 4.75 4.70 4.65 4.60 4.55 4.50 Volts

RD = 45.53 20.61 12.31 8.15 5.66 4.00 2.81 1.92 1.23 0.68 KOhms

Trim up 1 2 3 4 5 6 7 8 9 10 %

Vout = 12.12 12.24 12.36 12.48 12.60 12.72 12.84 12.96 13.08 13.20 Volts

RU = 367.91 165.95 98.64 64.98 44.78 31.32 21.70 14.49 8.88 4.39 KOhms

Trim down 1 2 3 4 5 6 7 8 9 10 %

Vout = 11.88 11.76 11.64 11.52 11.40 11.28 11.16 11.04 10.92 10.8 Volts

RD = 460.99 207.95 123.60 81.42 56.12 39.25 27.20 18.16 11.13 5.51 KOhms

Trim up 1 2 3 4 5 6 7 8 9 10 %

Vout = 15.15 15.3 15.45 15.60 15.75 15.90 16.05 16.20 16.35 16.50 Volts

RU = 404.18 180.59 106.06 68.80 46.44 31.53 20.88 12.90 6.69 1.72 KOhms

Trim down 1 2 3 4 5 6 7 8 9 10 %

Vout = 14.85 14.70 14.55 14.40 14.25 14.10 13.95 13.80 13.65 13.50 Volts

RD = 499.82 223.41 131.27 85.20 57.56 39.14 25.97 16.10 8.42 2.282 KOhms

RP30-xx05SEW

RP30-xx12SEW

RP30-xx15SEW

Trim up 1 2 3 4 5 6 7 8 9 10 %

Vout = 24.24 24.48 24.72 24.96 25.20 25.44 25.68 25.92 26.16 26.40 Volts

RU = 218.21 98.10 58.07 38.05 26.04 18.03 12.32 8.03 4.69 2.02 KOhms

Trim down 1 2 3 4 5 6 7 8 9 10 %

Vout = 23.76 23.52 23.28 23.04 22.80 22.56 22.32 22.08 21.84 21.6 Volts

RD = 273.44 123.02 72.87 47.80 32.76 22.73 15.57 10.20 6.02 2.67 KOhms

Trim up 1 2 3 4 5 6 7 8 9 10 %

Vout = 30.30 30.60 30.90 31.20 31.50 31.80 32.10 32.40 32.70 33.00 Volts

RU = 268.29 120.64 71.43 46.82 32.06 22.21 15.10 9.91 5.81 2.53 KOhms

Trim down 1 2 3 4 5 6 7 8 9 10 %

Vout = 29.70 29.40 29.10 28.80 28.50 28.20 27.90 27.60 27.30 27.00 Volts

RD = 337.71 152.02 90.13 59.18 40.61 28.23 19.39 12.76 7.60 3.47 KOhms

RP30-xx12DEW

RP30-xx15DEW

Dual Output Voltage Trim Tables

DC/DC Converter

Speciﬁcations measured at Ta = 25°C, nominal input voltage, full load otherwise noted

RP30-EW

Series

PD-5

REV.: 1/2016www.recom-power.com

PROTECTIONS

Parameter Condition Value

Short Circuit Protection (SCP) continuous, automatic recovery

Over Voltage Protection (OVP) Zener Diode Clamp

3.3Vout

5Vout

12Vout

15Vout

3.9VDC

6.2VDC

15VDC

18VDC

Over Load Protection (OLP) % of Iout rated 150% max.

Over Temperature Protection (OTP) 115°C typ.

Isolation Voltage I/P to O/P

I/P to O/P to case

1.6kVDC/1minute

Isolation Resistance 500VDC 1GΩ min.

Isolation Capacitance 1000pF max.

Notes:

Note9: This power module is not internally fused. An input line fuse must always be used.

ENVIRONMENTAL

Parameter Condition

Value

Operating Temperature Range without derating

with derating

-40°C to +70°C

-40°C to +100°C

Maximum Case Temperature +100°C

Temperature Coefﬁcient ±0.02%/°C max.

Thermal Impedance(10) Natural convection (20LFM)

Natural convection (20LFM) with Heat-sink

10°C/Watt

8.24°C/Watt

Operating Humidity 5% - 95% RH

Thermal Shock MIL-STD-810F

Vibration MIL-STD-810F

MTBF MIL-HDBK-217F

Bellcore TR-NWT-000332(10)

7598 x 102 hours

1315 x 103

hours

Notes:

Note10: BELLCORE TR-NWT-000332. Case l: 50% Stress, Temperature at 40°C (Ground ﬁxed and controlled environment).

Note11: Derating graphs are valid only for the shown part numbers. If you need detailed derating-information about a part-

number not shown here please contact our technical support service at techsupportAT@recom-power.com

-40 80 100 12040200-20

100

Ambient Temperature [°C]

Output Power [%]

60 70 -40 60 75

80 100 12040

200-20

100

Ambient Temperature [°C]

Output Power [%]

RP30-483.3SEW RP30-483.3SEW with Heat-sink

Derating Graph(11)

SAFETY AND CERTIFICATIONS

Certiﬁcate Type (Safety) Report / File Number Standard

UL General Safety E196683 UL60950-1 1st. Ed.: 2003

C22.2 No. 60950 1st. Ed.: 2003

EMC Compliance Condition Standard / Criterion

EMI Standard(12) with external ﬁlter EN55022, Class A, Class B

ESD

Radiated Immunity

Fast Transient(13)

Surge(13)

Conducted Immunity

Air ±8kV and Contact ±6kC

10 V/m

±2kV

±1kV

10 Vr.m.s

EN61000-4-2, Criteria B

EN61000-4-3, Criteria A

EN61000-4-4, Criteria A

EN61000-4-5, Criteria B

EN61000-4-6, Criteria A

PD-6 REV.: 1/2016 www.recom-power.com

DC/DC Converter

Speciﬁcations measured at Ta = 25°C, nominal input voltage, full load otherwise noted

RP30-EW

Series

Input

Fuse

C2C1

+VIN

+VOUT

-VOUT

-VIN

LOAD

+VIN

+VOUT

COM

-VOUT

-VIN

LOADLOAD

Input

Fuse

C2C1

+VIN

+VOUT

-VOUT

-VIN

LOAD

+VIN

+VOUT

COM

-VOUT

-VIN

LOADLOAD

EMI Filtering Class A

MODEL C1 C2 C3/C4

RP30-24xxSEW

RP30-24xxDEW

6.8µF/50V

1812 MLCC N/A 1000pF/2kV

1808 MLCC

RP30-48xxSEW

RP30-48xxDEW

2.2µF/100V

1812 MLCC

2.2µF/100V

1812 MLCC

1000pF/2kV

1808 MLCC

Input

Fuse

C3C2C1

+VIN

+VOUT

-VOUT

-VIN

LOAD

+VOUT

COM

-VOUT

LOADLOAD

+VIN

+VOUT

-VOUT

-VIN

Input

Fuse

C3C2C1

Input

Fuse

C3C2C1

+VIN

+VOUT

-VOUT

-VIN

LOAD

+VOUT

COM

-VOUT

LOADLOAD

+VIN

+VOUT

-VOUT

-VIN

Input

Fuse

C3C2C1

EMI Filtering Class B

MODEL C1 C2 C3 C4 C5/C6 L1

RP30-24xxSEW

RP30-24xxDEW

6.8µF/50V

1812 MLCC N/A 6.8F/50V

1812 MLCC N/A 1000pF/2kV

1808 MLCC

CMC: 450µH

ref.: WE 7448227005

ref.: CMC-05

RP30-48xxSEW

RP30-48xxDEW

2.2µF/100V

1812 MLCC

2.2µF/100V

1812 MLCC

2.2µF/100V

1812 MLCC

2.2µF/100V

1812 MLCC

1000pF/2kV

1808 MLCC

CMC: 450µH

ref.: WE 7448227005

ref.: CMC-05

Notes:

Note12: The standard modues meet EMI Class A or Class B with external components, see ﬁlter suggestions below.

Note13: An external input ﬁlter capacitor is required if the module has to meet EN61000-4-4, EN61000-4-5. The ﬁlter

capacitor Recom suggests: Nippon chemi-con KY series, 220µF/100V

DC/DC Converter

Speciﬁcations measured at Ta = 25°C, nominal input voltage, full load otherwise noted

RP30-EW

Series

PD-7

REV.: 1/2016www.recom-power.com

DIMENSIONS and PHYSICAL CHARACTERISTICS

Parameter Type Value

Material

Case

Base

Potting

Nickel coated copper

FR4 PCB

Epoxy (UL94-V0)

Package Dimensions (LxWxH) without Heat-sink

with Heat-sink

50.8 x 40.6 x 10.2mm

56.8 x 40.6 x 17.0mm

Package Weight without Heat-sink

with Heat-sink

48g

69.06g

Pin Connections

Pin # Single Dual

1 +Vin +Vin

2 -Vin -Vin

4 CTRL CTRL

5 No Pin +Vout

6 +Vout Com

7 -Vout -Vout

8 Trim Trim

Pin Pitch Tolerance ±0.25mm

Pin Dimension Tolerance ±0.1mm

Tolerance: X.X ±0.5mm

X.XX ±0.25mm

Dimension Drawing (mm)

40.6

5.60

50.8

10.2

Ø1.00

45.70

17.8015.20

5.10

10.20

12.7017.80

Bottom View

Dimension Drawing (mm) with Heat-sink

5.60

17.0

10.2

ø1.00

56.8

37.25

50.00

5.85

1.40 1.60

1.40 1.40

Top View

40.6

PD-8 REV.: 1/2016 www.recom-power.com

DC/DC Converter

Speciﬁcations measured at Ta = 25°C, nominal input voltage, full load otherwise noted

RP30-EW

Series

PACKAGING INFORMATION

Parameter Type Value

Packaging Quantity without Heat-sink

with Heat-sink

Tube

Tray

5pcs.

15pcs.

Storage Temperature Range -55°C to +125°C

Storage Humidity 5% - 95% RH

The product information and speciﬁcations are subject to change without prior notice. RECOM products are not authorized for use in safety-critical applications (such as life support) without RECOM’s explicit written

consent. A safety-critical application is deﬁned as an application where a failure of a RECOM product may reasonably be expected to endanger or cause loss of life, inﬂict bodily harm or damage property. The buyer

shall indemnify and hold harmless RECOM, its afﬁliated companies and its representatives against any damage claims in connection with the unauthorized use of RECOM products in such safety-critical applications.

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

RECOM:

RP30-2405SEW RP30-2405SEW/N RP30-2405SEW/N-HC RP30-2405SEW-HC RP30-2412DEW RP30-

2412DEW/N RP30-2412DEW/N-HC RP30-2412DEW-HC RP30-2412SEW RP30-2412SEW/N RP30-2412SEW/N-

HC RP30-2412SEW-HC RP30-2415DEW RP30-2415DEW/N RP30-2415DEW/N-HC RP30-2415DEW-HC RP30-

2415SEW RP30-2415SEW/N RP30-2415SEW/N-HC RP30-2415SEW-HC RP30-243.3SEW RP30-243.3SEW/N

RP30-243.3SEW/N-HC RP30-243.3SEW-HC RP30-4805SEW RP30-4805SEW/N RP30-4805SEW/N-HC RP30-

4805SEW-HC RP30-4812DEW RP30-4812DEW/N RP30-4812DEW/N-HC RP30-4812DEW-HC RP30-4812SEW

RP30-4812SEW/N RP30-4812SEW/N-HC RP30-4812SEW-HC RP30-4815DEW RP30-4815DEW/N RP30-

4815DEW/N-HC RP30-4815DEW-HC RP30-4815SEW RP30-4815SEW/N RP30-4815SEW/N-HC RP30-4815SEW-

HC RP30-483.3SEW RP30-483.3SEW/N RP30-483.3SEW/N-HC RP30-483.3SEW-HC