REVISIONS LTR DESCRIPTION Added suggested sources of supply; made editorial changes. Added suggested sources of supply. Deleted and added suggested sources of supply. Editorial changes throughout. Added suggested sources of supply. Changes to manufacturer PIN. Changes to paragraphs 3.2.2, 3.2.6, and 6.1. Editorial changes throughout. Changes in accordance with NOR 5910-R004-96 Revised sources of supply, added alternate marking method, made editorial changes, and converted references to MIL-PRF-49467. Moved solderability testing from group A to group B. Updated suggested sources of supply. Removed suggested source of supply. Added note 4 to figure 1. Added capacitor tolerance note to 3.2.9. Added suggested source of supply. Changed Johanson Dielectrics CAGE code. Updated name and address of vendor C. Added Johanson Dielectrics as a suggested source of supply. Added CalRamic Technologies as a suggested source of supply. Changed drawing type to Source Control with approved sources. Added manufacturer eligibility criteria, paragraph 3.14. Added new paragraph 6.3. Added an approved source. A B C D E F G H J K L M N DATE APPROVED 25 Sep 87 D. Moore 11 May 88 D. Moore 8 Oct 92 D. Moore 23 Feb 94 D. Moore 23 May 96 A. Ernst 5 April 99 J. Crum 10 April 00 Kendall A. Cottongim 16 January 01 Kendall A. Cottongim 12 September 01 Kendall A. Cottongim 4 November 02 Kendall A. Cottongim 18 August 2004 Kendall A. Cottongim 19 April 2007 Michael A. Radecki 21 October 2010 Michael A. Radecki CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Prepared in accordance with ASME Y14.100 REV STATUS OF PAGES PMIC N/A Source control drawing REV N N N N N N N N N PAGES 1 2 3 4 5 6 7 8 9 PREPARED BY ROBERT E. GRILLOT DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OH 45444-5000 Original date of drawing 1 April 1987 CHECKED BY EDWARD H. BACK APPROVED BY DAVID E. MOORE SIZE A REV AMSC N/A TITLE CAPACITORS, CERAMIC, MULTILAYER, HIGH VOLTAGE, X7R, 1,000 V DC CODE IDENT. NO. 14933 DWG NO. N PAGE 87043 1 OF 9 5910-E475 1. SCOPE 1.1 Scope. This drawing and MIL-PRF-49467 describe the requirements for high voltage multilayer ceramic capacitors. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 87043 | | Drawing number -XX | | Dash number (see table I) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-49467 - Capacitor, Fixed, Ceramic, Multilayer, High Voltage (General Purpose), Established Reliability, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-202 MIL-STD-1285 - Test Methods Standard Electronics and Electrical Component Parts. Marking of Electrical and Electronic Parts. (Copies of these documents are available online at https://assist.daps.dla.mil/quicksearch/ or https://www.assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. The interface and physical dimensions shall be as specified in MIL-PRF-49467 and herein (see figure 1). 3.1.1 Leads. Leads shall be solder coated. Tin-lead (Sn-Pb) finishes are acceptable provided that the minimum lead content is 3 percent. 3.1.2 Case. Epoxy, conformally coated. 3.1.3 Operating temperature range. The operating temperature range shall be -55C to +125C. 3.2 Electrical characteristics. 3.2.1 Rated voltage. The rated voltage shall be 1,000 volts dc. 3.2.2 Dielectric type. X7R. DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 87043 REV N PAGE 2 Case code A B C D E F G Width (W) .250 .320 .370 .470 .570 .670 .770 Sizes (max.) Height Thickness (H) (T) .220 .280 .300 .400 .500 .600 .720 .200 .250 .250 .270 .270 .270 .270 Inches .002 .025 .030 .170 .200 .220 .250 .270 .275 .280 .300 .320 .370 Lead spacing .030 (S) .170 .220 .275 .375 .475 .575 .675 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. H dimension includes meniscus. 4. S dimension shall be maintained from chip body to end of leads. mm 0.05 0.64 0.76 4.32 5.08 5.59 6.35 6.86 6.99 7.11 7.62 8.13 9.40 Inches .375 .400 .470 .475 .500 .570 .575 .600 .670 .675 .720 .770 1.250 mm 9.53 10.16 11.94 12.07 12.70 14.48 14.61 15.24 17.02 17.15 18.29 19.56 31.75 FIGURE 1. Case dimensions and configuration. DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 87043 REV N PAGE 3 3.2.3 Temperature coefficient. 15 percent. (For MIL-PRF-49467 group B voltage temperature limits, use step a through step d only.) 3.2.4 Capacitance. See table I. Measured in accordance with method 305 of MIL-STD-202, 1 kHz at 1.0 V rms at +25C. 3.2.5 Dissipation factor (+25C). 2.5 percent maximum (measured under the same conditions as capacitance). 3.2.6 Insulation resistance. Measured in accordance with method 302 of MIL-STD-202. At +25C, 500 V dc: 100,000 megohms or 1,000 megohms microfarad, whichever is less. At +125C, 500 V dc: 10,000 megohms or 100 megohms microfarad, whichever is less. 3.2.7 Dielectric withstanding voltage. 1.2 times rated voltage. 3.2.8 Aging rate. -2.0 percent maximum per decade-hour. 3.2.9 Capacitance tolerance. K = 10 percent, M = 20 percent. K tolerance parts may be substituted for M tolerance parts, with acquiring activity approval. 3.3 Solderability of terminals. In accordance with MIL-PRF-49467. 3.4 Vibration. In accordance with MIL-PRF-49467. 3.5 Shock. In accordance with MIL-PRF-49467. 3.6 Immersion cycling. In accordance with MIL-PRF-49467. 3.7 Moisture resistance. In accordance with MIL-PRF-49467. 3.8 Life. One hundred percent of rated voltage applied at +125C for 1,000 hours. Resistors with a high value such as 1 megohm may be used in series with each part under test in lieu of fuses. 3.9 Thermal shock. Method 107, MIL-STD-202, test condition B except low temperature is -55C. 3.10 Voltage conditioning. In accordance with MIL-PRF-49467, 100 percent of rated voltage. Resistors with a high value such as 1 megohm may be used in series with each part under test in lieu of fuses. 3.11 Terminal strength. In accordance with MIL-PRF-49467. 3.12 Marking. Marking shall be in accordance with MIL-STD-1285 except the capacitors shall be marked with the PIN as specified in 1.2, the manufacturer's name or Commercial and Government Entity (CAGE) code, and date lot code as a minimum. Case codes A, B, and C (at the option of the manufacturer) may be marked as indicated below with full marking on the package. Front Back Last 3 digits of drawing number---- 043 XYZ ------ Manufacturer's trademark Dash number -------------------------- -49 430 ------ Date code FIGURE 2. Alternate marking method for A, B, and C case codes. 3.13 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.14 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on the MIL-PRF-49467 Qualified Products Database for at least one part, or provide data as requested by DLA Land and Maritime - VAT. 3.15 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approved source of supply. DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 87043 REV N PAGE 4 3.16 Workmanship. Capacitors shall be uniform in quality and free from any defects that will affect life, serviceability, or appearance. TABLE I. Electrical characteristics DSCC drawing 8704301 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 Capacitance Capacitance tolerance Case code K M K M K M K M K M K M K M K M K M K M K M K M K M K M K M K M K M K M K M K M K M K M K A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A 100 pF 100 pF 120 pF 120 pF 150 pF 150 pF 180 pF 180 pF 220 pF 220 pF 270 pF 270 pF 330 pF 330 pF 390 pF 390 pF 470 pF 470 pF 560 pF 560 pF 680 pF 680 pF 820 pF 820 pF 1000 pF 1000 pF 1200 pF 1200 pF 1500 pF 1500 pF 1800 pF 1800 pF 2200 pF 2200 pF 2700 pF 2700 pF 3300 pF 3300 pF 3900 pF 3900 pF 4700 pF 4700 pF 5600 pF 5600 pF 6800 pF DSCC drawing 8704346 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 Capacitance Capacitance tolerance Case code 6800 pF 8200 pF 8200 pF .01 F .01 F .012 F .012 F .015 F .015 F .018 F .018 F .022 F .022 F .027 F .027 F .033 F .033 F .039 F .039 F .047 F .047 F .056 F .056 F .068 F .068 F .082 F .082 F .10 F .10 F .12 F .12 F .15 F .15 F .18 F .18 F .22 F .22 F .27 F .27 F .33 F .33 F .39 F .39 F .47 F .47 F M K M K M K M K M K M K M K M K M K M K M K M K M K M K M K M K M K M K M K M K M K M K M A A A A A B B B B B B B B C C D D D D D D D D D D E E E E E E E E F F F F F F G G G G G G DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 87043 REV N PAGE 5 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection is not required. 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of all tests specified in group A and group B inspections of MIL-PRF-49467, provided they are listed in this drawing. PPM testing and calculation is not applicable. Solderability testing shall be performed as a separate subgroup of group B inspection with a sample size of 3 units and 0 defectives permitted. 4.2.2 Certification. The acquiring activity, at its discretion, may accept a certificate of compliance with group B requirements in lieu of performing group B tests (see 6.2d). 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Point's packaging activities within the Military Service or Defense Agency, or within the military service's system commands. Packaging data retrieval is available from the managing Military Department's or Defense Agency's automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. Capacitors conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not available for original equipment manufacturer application. This drawing is intended exclusively to prevent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog listings. When a military specification exists and the product covered by this drawing has been qualified for listing, this drawing becomes obsolete and will not be used for new design. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. d. Whether the manufacturer performs the group B tests or provides certification of compliance with group B requirements. e. Requirements for notification of change of product to procuring activity, if applicable. 6.3 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM B545 (Standard Specification for Electrodeposited Coating of Tin). 6.4 Replaceability. Capacitors covered by this drawing will replace the same commercial device covered by contractor prepared specification or drawing. 6.5 Users of record. Coordination of this document for future revisions is coordinated only with the approved sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing should be in writing to: DLA Land and Maritime, ATTN: VAT, Post Office Box 3990, Columbus, OH 43218-3990 or e-mailed to capacitorfilter@dla.mil also by telephone (614) 692-4709 or DSN 850-4709. DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 87043 REV N PAGE 6 DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 REV N DWG NO. 87043 PAGE 1/ DSCC drawing PIN 8704301 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 Vendor A similar vendor type Vendor B similar vendor type Vendor C and J similar vendor type Vendor D similar vendor type Vendor E Vendor F similar similar vendor type vendor type SV01AC101KHA SV01AC101MHA SV01AC121KHA SV01AC121MHA SV01AC151KHA SV01AC151MHA SV01AC181KHA SV01AC181MHA SV01AC221KHA SV01AC221MHA SV01AC271KHA SV01AC271MHA SV01AC331KHA SV01AC331MHA SV01AC391KHA SV01AC391MHA SV01AC471KHA SV01AC471MHA SV01AC561KHA SV01AC561MHA SV01AC681KHA SV01AC681MHA SV01AC821KHA SV01AC821MHA SV01AC102KHA SV01AC102MHA SV01AC122KHA SV01AC122MHA SV01AC152KHA SV01AC152MHA SV01AC182KHA SV01AC182MHA SV01AC222KHA SV01AC222MHA SV01AC272KHA SV01AC272MHA SV01AC332KHA SV01AC332MHA SV01AC392KHA SV01AC392MHA SV01AC472KHA SV01AC472MHA SV01AC562KHA SV01AC562MHA SV01AC682KHA SV01AC682MHA SV01AC822KHA SV01AC822MHA 1515CX101KA102 1515CX101MA102 1515CX121KA102 1515CX121MA102 1515CX151KA102 1515CX151MA102 1515CX181KA102 1515CX181MA102 1515CX221KA102 1515CX221MA102 1515CX271KA102 1515CX271MA102 1515CX331KA102 1515CX331MA102 1515CX391KA102 1515CX391MA102 1515CX471KA102 1515CX471MA102 1515CX561KA102 1515CX561MA102 1515CX681KA102 1515CX681MA102 1515CX821KA102 1515CX821MA102 1515CX102KA102 1515CX102MA102 1515CX122KA102 1515CX122MA102 1515CX152KA102 1515CX152MA102 1515CX182KA102 1515CX182MA102 1515CX222KA102 1515CX222MA102 1515CX272KA102 1515CX272MA102 1515CX332KA102 1515CX332MA102 1515CX392KA102 1515CX392MA102 1515CX472KA102 1515CX472MA102 1515CX562KA102 1515CX562MA102 1515CX682KA102 1515CX682MA102 1515CX822KA102 1515CX822MA102 102H42W101KQ3H 102H42W101MQ3H 102H42W121KQ3H 102H42W121MQ3H 102H42W151KQ3H 102H42W151MQ3H 102H42W181KQ3H 102H42W181MQ3H 102H42W221KQ3H 102H42W221MQ3H 102H42W271KQ3H 102H42W271MQ3H 102H42W331KQ3H 102H42W331MQ3H 102H42W391KQ3H 102H42W391MQ3H 102H42W471KQ3H 102H42W471MQ3H 102H42W561KQ3H 102H42W561MQ3H 102H42W681KQ3H 102H42W681MQ3H 102H42W821KQ3H 102H42W821MQ3H 102H42W102KQ3H 102H42W102MQ3H 102H42W122KQ3H 102H42W122MQ3H 102H42W152KQ3H 102H42W152MQ3H 102H42W182KQ3H 102H42W182MQ3H 102H42W222KQ3H 102H42W222MQ3H 102H42W272KQ3H 102H42W272MQ3H 102H42W332KQ3H 102H42W332MQ3H 102H42W392KQ3H 102H42W392MQ3H 102H42W472KQ3H 102H42W472MQ3H 102H42W562KQ3H 102H42W562MQ3H 102H42W682KQ3H 102H42W682MQ3H 102H42W822KQ3H 102H42W822MQ3H UTC4124-01 UTC4124-02 UTC4124-03 UTC4124-04 UTC4124-05 UTC4124-06 UTC4124-07 UTC4124-08 UTC4124-09 UTC4124-10 UTC4124-11 UTC4124-12 UTC4124-13 UTC4124-14 UTC4124-15 UTC4124-16 UTC4124-17 UTC4124-18 UTC4124-19 UTC4124-20 UTC4124-21 UTC4124-22 UTC4124-23 UTC4124-24 UTC4124-25 UTC4124-26 UTC4124-27 UTC4124-28 UTC4124-29 UTC4124-30 UTC4124-31 UTC4124-32 UTC4124-33 UTC4124-34 UTC4124-35 UTC4124-36 UTC4124-37 UTC4124-38 UTC4124-39 UTC4124-40 UTC4124-41 UTC4124-42 UTC4124-43 UTC4124-44 UTC4124-45 UTC4124-46 UTC4124-47 UTC4124-48 126449-01 126449-02 126449-03 126449-04 126449-05 126449-06 126449-07 126449-08 126449-09 126449-10 126449-11 126449-12 126449-13 126449-14 126449-15 126449-16 126449-17 126449-18 126449-19 126449-20 126449-21 126449-22 126449-23 126449-24 126449-25 126449-26 126449-27 126449-28 126449-29 126449-30 126449-31 126449-32 126449-33 126449-34 126449-35 126449-36 126449-37 126449-38 126449-39 126449-40 126449-41 126449-42 126449-43 126449-44 126449-45 126449-46 126449-47 126449-48 See footnote at end of table. PCI1556-01 PCI1556-02 PCI1556-03 PCI1556-04 PCI1556-05 PCI1556-06 PCI1556-07 PCI1556-08 PCI1556-09 PCI1556-10 PCI1556-11 PCI1556-12 PCI1556-13 PCI1556-14 PCI1556-15 PCI1556-16 PCI1556-17 PCI1556-18 PCI1556-19 PCI1556-20 PCI1556-21 PCI1556-22 PCI1556-23 PCI1556-24 PCI1556-25 PCI1556-26 PCI1556-27 PCI1556-28 PCI1556-29 PCI1556-30 PCI1556-31 PCI1556-32 PCI1556-33 PCI1556-34 PCI1556-35 PCI1556-36 PCI1556-37 PCI1556-38 PCI1556-39 PCI1556-40 PCI1556-41 PCI1556-42 PCI1556-43 PCI1556-44 PCI1556-45 PCI1556-46 PCI1556-47 PCI1556-48 Vendor G similar vendor type Vendor H similar vendor type 1515N101K102LEXH 1515N101M102LEXH 1515N121K102LEXH 1515N121M102LEXH 1515N151K102LEXH 1515N151M102LEXH 1515N181K102LEXH 1515N181M102LEXH 1515N221K102LEXH 1515N221M102LEXH 1515N271K102LEXH 1515N271M102LEXH 1515B331K102LEXH 1515B331M102LEXH 1515B391K102LEXH 1515B391M102LEXH 1515B471K102LEXH 1515B471M102LEXH 1515B561K102LEXH 1515B561M102LEXH 1515B681K102LEXH 1515B681M102LEXH 1515B821K102LEXH 1515B821M102LEXH 1515B102K102LEXH 1515B102M102LEXH 1515B122K102LEXH 1515B122M102LEXH 1515B152K102LEXH 1515B152M102LEXH 1515B182K102LEXH 1515B182M102LEXH 1515B222K102LEXH 1515B222M102LEXH 1515B272K102LEXH 1515B272M102LEXH 1515B332K102LEXH 1515B332M102LEXH 1515B392K102LEXH 1515B392M102LEXH 1515B472K102LEXH 1515B472M102LEXH 1515B562K102LEXH 1515B562M102LEXH 1515B682K102LEXH 1515B682M102LEXH 1515B822K102LEXH 1515B822M102LEXH 10HV01B101KM 10HV01B101MM 10HV01B121KM 10HV01B121MM 10HV01B151KM 10HV01B151MM 10HV01B181KM 10HV01B181MM 10HV01B221KM 10HV01B221MM 10HV01B271KM 10HV01B271MM 10HV01B331KM 10HV01B331MM 10HV01B391KM 10HV01B391MM 10HV01B471KM 10HV01B471MM 10HV01B561KM 10HV01B561MM 10HV01B681KM 10HV01B681MM 10HV01B821KM 10HV01B821MM 10HV01B102KM 10HV01B102MM 10HV01B122KM 10HV01B122MM 10HV01B152KM 10HV01B152MM 10HV01B182KM 10HV01B182MM 10HV01B222KM 10HV01B222MM 10HV01B272KM 10HV01B272MM 10HV01B332KM 10HV01B332MM 10HV01B392KM 10HV01B392MM 10HV01B472KM 10HV01B472MM 10HV01B562KM 10HV01B562MM 10HV01B682KM 10HV01B682MM 10HV01B822KM 10HV01B822MM 7 DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 REV N 1/ DSCC drawing PIN 8704349 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 Vendor A similar vendor type Vendor B similar vendor type Vendor C and J similar vendor type Vendor D similar vendor type Vendor E Vendor F similar similar vendor type vendor type SV01AC103KHA SV01AC103MHA SV02AC123KHA SV02AC123MHA SV02AC153KHA SV02AC153MHA SV02AC183KHA SV02AC183MHA SV02AC223KHA SV02AC223MHA SV03AC273KHA SV03AC273MHA SV05AC333KHA SV05AC333MHA SV05AC393KHA SV05AC393MHA SV05AC473KHA SV05AC473MHA SV05AC563KHA SV05AC563MHA SV05AC683KHA SV05AC683MHA SV07AC823KHA SV07AC823MHA SV07AC104KHA SV07AC104MHA SV07AC124KHA SV07AC124MHA SV07AC154KHA SV07AC154MHA SV08AC184KHA SV08AC184MHA SV08AC224KHA SV08AC224MHA SV08AC274KHA SV08AC274MHA SV09AC334KHA SV09AC334MHA SV09AC394KHA SV09AC394MHA SV09AC474KHA SV09AC474MHA 1515CX103KA102 1515CX103MA102 2020CX123KA102 2020CX123MA102 2020CX153KA102 2020CX153MA102 2020CX183KA102 2020CX183MA102 2020CX223KA102 2020CX223MA102 2520CX273KA102 2520CX273MA102 3530CX333KA102 3530CX333MA102 3530CX393KA102 3530CX393MA102 3530CX473KA102 3530CX473MA102 3530CX563KA102 3530CX563MA102 3530CX683KA102 3530CX683MA102 4540CX823KA102 4540CX823MA102 4540CX104KA102 4540CX104MA102 4540CX124KA102 4540CX124MA102 4540CX154KA102 4540CX154MA102 5550CX184KA102 5550CX184MA102 5550CX224KA102 5550CX224MA102 5550CX274KA102 5550CX274MA102 6560CX334KA102 6560CX334MA102 6560CX394KA102 6560CX394MA102 6560CX474KA102 6560CX474MA102 102H42W103KQ3H 102H42W103MQ3H 102H46W123KQ3H 102H46W123MQ3H 102H46W153KQ3H 102H46W153MQ3H 102H46W183KQ3H 102H46W183MQ3H 102H46W223KQ3H 102H46W223MQ3H 102H47W273KQ3H 102H47W273MQ3H 102H51W333KQ3H 102H51W333MQ3H 102H51W393KQ3H 102H51W393MQ3H 102H51W473KQ3H 102H51W473MQ3H 102H51W563KQ3H 102H51W563MQ3H 102H51W683KQ3H 102H51W683MQ3H 102H62W823KQ3H 102H62W823MQ3H 102H62W104KQ3H 102H62W104MQ3H 102H62W124KQ3H 102H62W124MQ3H 102H62W154KQ3H 102H62W154MQ3H 102H66W184KQ3H 102H66W184MQ3H 102H66W224KQ3H 102H66W224MQ3H 102H66W274KQ3H 102H66W274MQ3H 102H70W334KQ3H 102H70W334MQ3H 102H70W394KQ3H 102H70W394MQ3H 102H70W474KQ3H 102H70W474MQ3H UTC4124-49 UTC4124-50 UTC4124-51 UTC4124-52 UTC4124-53 UTC4124-54 UTC4124-55 UTC4124-56 UTC4124-57 UTC4124-58 UTC4124-59 UTC4124-60 UTC4124-61 UTC4124-62 UTC4124-63 UTC4124-64 UTC4124-65 UTC4124-66 UTC4124-67 UTC4124-68 UTC4124-69 UTC4124-70 UTC4124-71 UTC4124-72 UTC4124-73 UTC4124-74 UTC4124-75 UTC4124-76 UTC4124-77 UTC4124-78 UTC4124-79 UTC4124-80 UTC4124-81 UTC4124-82 UTC4124-83 UTC4124-84 UTC4124-85 UTC4124-86 UTC4124-87 UTC4124-88 UTC4124-89 UTC4124-90 126449-49 126449-50 126449-51 126449-52 126449-53 126449-54 126449-55 126449-56 126449-57 126449-58 126449-59 126449-60 126449-61 126449-62 126449-63 126449-64 126449-65 126449-66 126449-67 126449-68 126449-69 126449-70 126449-71 126449-72 126449-73 126449-74 126449-75 126449-76 126449-77 126449-78 126449-79 126449-80 126449-81 126449-82 126449-83 126449-84 126449-85 126449-86 126449-87 126449-88 126449-89 126449-90 PCI1556-49 PCI1556-50 PCI1556-51 PCI1556-52 PCI1556-53 PCI1556-54 PCI1556-55 PCI1556-56 PCI1556-57 PCI1556-58 PCI1556-59 PCI1556-60 PCI1556-61 PCI1556-62 PCI1556-63 PCI1556-64 PCI1556-65 PCI1556-66 PCI1556-67 PCI1556-68 PCI1556-69 PCI1556-70 PCI1556-71 PCI1556-72 PCI1556-73 PCI1556-74 PCI1556-75 PCI1556-76 PCI1556-77 PCI1556-78 PCI1556-79 PCI1556-80 PCI1556-81 PCI1556-82 PCI1556-83 PCI1556-84 PCI1556-85 PCI1556-86 PCI1556-87 PCI1556-88 PCI1556-89 PCI1556-90 Vendor G similar vendor type Vendor H similar vendor type 1515B103K102LEXH 1515B103M102LEXH 2020B123K102LEXH 2020B123M102LEXH 2020B153K102LEXH 2020B153M102LEXH 2020B183K102LEXH 2020B183M102LEXH 2020B223K102LEXH 2020B223M102LEXH 2520B273K102LEXH 2520B273M102LEXH 3530B333K102LEXH 3530B333M102LEXH 3530B393K102LEXH 3530B393M102LEXH 3530B473K102LEXH 3530B473M102LEXH 3530B563K102LEXH 3530B563M102LEXH 3530B683K102LEXH 3530B683M102LEXH 4540B823K102LEXH 4540B823M102LEXH 4540B104K102LEXH 4540B104M102LEXH 4540B124K102LEXH 4540B124M102LEXH 4540B154K102LEXH 4540B154M102LEXH 5550B184K102LEXH 5550B184M102LEXH 5550B224K102LEXH 5550B224M102LEXH 5550B274K102LEXH 5550B274M102LEXH 6560B334K102LEXH 6560B334M102LEXH 6560B394K102LEXH 6560B394M102LEXH 6560B474K102LEXH 6560B474M102LEXH 10HV01B103KM 10HV01B103MM 10HV02B123KM 10HV02B123MM 10HV02B153KM 10HV02B153MM 10HV02B183KM 10HV02B183MM 10HV02B223KM 10HV02B223MM 10HV03B273KM 10HV03B273MM 10HV04B333KM 10HV04B333MM 10HV04B393KM 10HV04B393MM 10HV04B473KM 10HV04B473MM 10HV04B563KM 10HV04B563MM 10HV04B683KM 10HV04B683MM 10HV05B823KM 10HV05B823MM 10HV05B104KM 10HV05B104MM 10HV05B124KM 10HV05B124MM 10HV05B154KM 10HV05B154MM 10HV06B184KM 10HV06B184MM 10HV06B224KM 10HV06B224MM 10HV06B274KM 10HV06B274MM 10HV07B334KM 10HV07B334MM 10HV07B394KM 10HV07B394MM 10HV07B474KM 10HV07B474MM 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. DWG NO. 87043 PAGE 8 6.6 Approved sources of supply. Approved sources of supply are listed herein. Additional sources will be added as they become available. For assistance in the use of this drawing, contact DLA Land and Maritime, ATTN: VAT, Post Office Box 3990, Columbus, OH 43218-3990 or e-mailed to capacitorfilter@dla.mil also by telephone (614) 692-4709 or DSN 850-4709. Vendor Vendor CAGE Vendor name and address A 96095 Olean Advanced Products A Division of AVX Corporation 1695 Seneca Avenue Olean NY 14760-3736 B 63980 Wright Capacitors Incorporated 2610 South Oak Street Santa Ana CA 92707-3720 C 07EN1 Advanced Monolythic Ceramics, Incorporated 3101 Constitution Avenue, Suite 100 Olean NY 14760-1867 D 0YBX7 Union Technology Corporation 718 Monterey Pass Road Monterey Park CA 91754-3607 E 0LR95 Spectrum Control Technology Incorporated 1900 West College Avenue State College, PA 16801 F 60212 Presidio Components Incorporated 7169 Construction Court San Diego CA 92121-2615 G 65238 Novacap 25136 Anza Drive Valencia CA 91355-3415 H 3H3G4 CalRamic Technologies LLC 5462 Louie Lane Reno, NV 89511 J 29454 Johanson Dielectrics, Inc 15191 Bledsoe Avenue Sylmar, CA 91342 DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 87043 REV N PAGE 9