NL17SG373 Low-Power D-Type Transparent Latch with 3-State Output The NL17SG373 MiniGateTM is an advanced high-speed CMOS D-Type Transparent Latch with 3-State Output in ultra-small footprint. The NL17SG373 input structures provide protection when voltages up to 5.5 V are applied, regardless of the supply voltage. This device is fully specified for partial power-down applications using IOFF. The IOFF circuitry disables the output, preventing the damaging backflow current through the device when it is powered down. http://onsemi.com MARKING DIAGRAMS 6 SC-88 DF SUFFIX CASE 419B 1 AG M G G Features * * * * * * 1 Wide Operating VCC Range: 0.9 V to 3.6 V High Speed: tPD = 2.4 ns (Typ) @ VCC = 3.0 V, CL = 15 pF Low Power Dissipation: ICC = 0.5 mA (Max) at TA = 25C 5.5 V Overvoltage Tolerant (OVT) Input Pins Ultra-Small Packages These Devices are Pb-Free and are RoHS Compliant AG M G = Device Code = Date Code* = Pb-Free Package (Note: Microdot may be in either location) *Date Code orientation and/or position may vary depending upon manufacturing location. PIN ASSIGNMENT Pin Figure 1. SC88 (Top View) Function 1 LE 2 GND 3 D 4 Q 5 VCC 6 OE ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 9 of this data sheet. Figure 2. Logic Symbol (c) Semiconductor Components Industries, LLC, 2014 June, 2014 - Rev. 1 1 Publication Order Number: NL17SG373/D NL17SG373 FUNCTION TABLE Input Output OE LE D Internal Latch Q L H L L L Enable and Read Register L H H H H (Transparent Mode) L L L L L Latch and Read Register L L H H H H X X X Z Operating Mode Latch Register and Disable Output MAXIMUM RATINGS Symbol Parameter Value Unit VCC DC Supply Voltage -0.5 to +5.5 V VIN DC Input Voltage -0.5 to +5.5 V -0.5 to VCC + 0.5 V VOUT DC Output Voltage IIK DC Input Diode Current VIN < GND -50 mA IOK DC Output Diode Current VOUT < GND, VOUT > VCC 50 mA IO DC Output Source/Sink Current 20 mA ICC DC Supply Current Per Supply Pin 50 mA IGND DC Ground Current per Ground Pin 50 mA TSTG Storage Temperature Range -65 to +150 C TL Lead Temperature, 1 mm from Case for 10 Seconds 260 C TJ Junction Temperature Under Bias 150 C MSL FR VESD ILATCHUP Moisture Sensitivity Level 1 Flammability Rating Oxygen Index: 28 to 34 UL 94 V-0 @ 0.125 in ESD Withstand Voltage Human Body Mode (Note 2) Machine Model (Note 3) Latchup Performance Above VCC and Below GND at 125C (Note 4) > 3000 > 200 V 100 mA Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 1. Measured with minimum pad spacing on an FR4 board, using 10 mm-by-1 inch, 2 ounce copper trace no air flow. 2. Tested to EIA / JESD22-A114-A. 3. Tested to EIA / JESD22-A115-A. 4. Tested to EIA / JESD78. RECOMMENDED OPERATING CONDITIONS Symbol Parameter Min Max Unit 0.9 3.6 V VCC Positive DC Supply Voltage VIN Digital Input Voltage 0 3.6 V Output Voltage Active Mode 0 VCC V -55 +125 C 0 10 nS/V VOUT TA Dt / DV Operating Free-Air Temperature Input Transition Rise or Fail Rate VCC = 3.3 V 0.3 V Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond the Recommended Operating Ranges limits may affect device reliability. http://onsemi.com 2 NL17SG373 DC ELECTRICAL CHARACTERISTICS TA = -555C to +1255C TA = 255C Symbol Parameter VIH High-Level Input Voltage VIL VOH VOL Conditions Low-Level Input Voltage High-Level Output Voltage Low-Level Output Voltage VIN = VIH or VIL VCC (V) Min Typ Max Min 0.9 VCC VCC 1.1 to 1.3 0.7 x VCC 0.7 x VCC 1.4 to 1.6 0.65 x VCC 0.65 x VCC 1.65 to 1.95 0.65 x VCC 0.65 x VCC 2.3 to 2.7 1.7 1.7 3.0 to 3.6 2.0 2.0 Max V 0.9 GND GND 1.1 to 1.3 0.3 x VCC 0.3 x VCC 1.4 to 1.6 0.35 x VCC 0.35 x VCC 1.65 to 1.95 0.35 x VCC 0.35 x VCC 2.3 to 2.7 0.7 0.7 3.0 to 3.6 0.8 0.8 IOH = -20 mA 0.9 0.75 0.75 IOH = -0.3 mA 1.1 to 1.3 0.75 x VCC 0.75 x VCC IOH = -1.7 mA 1.4 to 1.6 0.75 x VCC 0.75 x VCC IOH = -3.0 mA 1.65 to 1.95 VCC - 0.45 VCC - 0.45 IOH = -4.0 mA 2.3 to 2.7 2.0 2.0 IOH = -8.0 mA 3.0 to 3.6 2.48 2.48 Unit V V IOL = 20 mA 0.9 0.1 0.1 IOL = 0.3 mA 1.1 to 1.3 0.25 x VCC 0.25 x VCC IOL = 1.7 mA 1.4 to 1.6 0.25 x VCC 0.25 x VCC IOL = 3.0 mA 1.65 to 1.95 0.45 0.45 IOL = 4.0 mA 2.3 to 2.7 0.4 0.4 IOL = 8.0 mA 3.0 to 3.6 0.4 0.4 0 VIN 3.6 V 0 to 3.6 0.1 0.5 mA VIN = VIH or VIL V IIN Input Leakage Current ICC Quiescent Supply Current VIN = VCC or GND 3.6 0.5 10 mA IOZ 3-State Output Leakage Current VIN = VIH or VIL; VOUT = 0 to 3.6 V 0.9 to 3.6 0.1 1 mA Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be indicated by the Electrical Characteristics if operated under different conditions. http://onsemi.com 3 NL17SG373 AC ELECTRICAL CHARACTERISTICS (Input tr = tf = 3.0 ns) TA = -555C to +1255C TA = 25 5C Symbol Parameter Test Condition VCC (V) Min Typ Max Min Max Unit tPLH, tPHL Propagation Delay, D to Q CL = 10 pF, RL = 1 MW 0.9 - 15.3 - - - ns 1.1 to 1.3 - 6.3 12.3 1.0 14.4 1.4 to 1.6 - 4.4 8.1 1.0 9.4 1.65 to 1.95 - 3.6 6.2 0.5 6.7 2.3 to 2.7 - 2.6 3.9 0.5 4.4 3.0 to 3.6 - 2.1 3.1 0.5 3.7 0.9 - 17.7 - - - 1.1 to 1.3 - 7.1 13.6 1.0 15.6 1.4 to 1.6 - 5.0 9.2 1.0 10.4 1.65 to 1.95 - 4.1 6.9 1.0 7.1 2.3 to 2.7 - 2.9 4.4 0.5 5.0 3.0 to 3.6 - 2.4 3.4 0.5 3.9 0.9 - 29 - - - 1.1 to 1.3 - 9.3 17.3 1.0 21.2 1.4 to 1.6 - 6.4 11.6 1.0 12.6 1.65 to 1.95 - 5.3 9.1 1.0 9.6 2.3 to 2.7 - 4 5.7 1.0 6.1 3.0 to 3.6 - 3.3 4.4 1.0 4.8 0.9 - 15.3 - - - 1.1 to 1.3 - 6.3 12.3 1.0 14.4 1.4 to 1.6 - 4.4 8.1 1.0 9.4 1.65 to 1.95 - 3.6 6.2 0.5 6.7 2.3 to 2.7 - 2.6 3.9 0.5 4.4 3.0 to 3.6 - 2.1 3.1 0.5 3.7 CL = 15 pF, RL = 1 MW CL = 30 pF, RL = 1 MW tPLH, tPHL Propagation Delay, LE to Q CL = 10 pF, RL = 1 MW CL = 15 pF, RL = 1 MW CL = 30 pF, RL = 1 MW 0.9 - 17.7 - - - 1.1 to 1.3 - 7.1 13.6 1.0 15.6 1.4 to 1.6 - 5.0 9.2 1.0 10.4 1.65 to 1.95 - 4.1 6.9 1.0 7.1 2.3 to 2.7 - 2.9 4.4 0.5 5.0 3.0 to 3.6 - 2.4 3.4 0.5 3.9 0.9 - 29 - - - 1.1 to 1.3 - 9.3 17.3 1.0 21.2 1.4 to 1.6 - 6.4 11.6 1.0 12.6 1.65 to 1.95 - 5.3 9.1 1.0 9.6 2.3 to 2.7 - 4 5.7 1.0 6.1 3.0 to 3.6 - 3.3 4.4 1.0 4.8 http://onsemi.com 4 ns ns ns ns ns NL17SG373 AC ELECTRICAL CHARACTERISTICS (Input tr = tf = 3.0 ns) TA = -555C to +1255C TA = 25 5C Symbol Parameter Test Condition CL = 10 pF, RL = 5 kW tPZH, tPZL Output Enable Time, OE to Q CL = 15 pF, RL = 5 kW CL = 30 pF, RL = 5 kW CL = 10 pF, RL = 5 kW tPHZ, tPLZ Output Disable Time, OE to Q CL = 15 pF, RL = 5 kW CL = 30 pF, RL = 5 kW VCC (V) Min Typ Max Min Max 0.9 - 18.9 - - - 1.1 to 1.3 - 6.0 10.2 1 10.6 1.4 to 1.6 - 4.5 6.5 1 7.0 1.65 to 1.95 - 3.9 5.4 1 5.8 2.3 to 2.7 - 2.5 3.5 1 3.8 3.0 to 3.6 - 2.1 2.7 1 3 0.9 - 22 - - - 1.1 to 1.3 - 6.8 11.6 1 12.1 1.4 to 1.6 - 5.1 7.2 1 7.9 1.65 to 1.95 - 4.4 6.1 1 6.5 2.3 to 2.7 - 2.9 3.9 1 4.2 3.0 to 3.6 - 2.3 3 1 3.3 0.9 - 31.8 - - - 1.1 to 1.3 - 9.1 15.7 1 16.2 1.4 to 1.6 - 6.7 9.5 1 10.5 1.65 to 1.95 - 5.7 7.9 1 8.6 2.3 to 2.7 - 3.8 5 1 5.5 3.0 to 3.6 - 2.9 3.8 1 4.2 0.9 - 11.3 - - - 1.1 to 1.3 - 5.3 8.3 1 8.4 1.4 to 1.6 - 4.1 5.8 1 6.1 1.65 to 1.95 - 4.2 5.7 1 5.9 2.3 to 2.7 - 3.0 4 1 4.2 3.0 to 3.6 - 3.4 4.7 1 5 0.9 - 11 - - - 1.1 to 1.3 - 5.8 8.2 1 11 1.4 to 1.6 - 3.9 5.9 1 8 1.65 to 1.95 - 4.5 6.6 1 7.4 2.3 to 2.7 - 3.2 4.3 1 5.1 3.0 to 3.6 - 4.8 6.2 1 6.7 0.9 - 17.7 - - - 1.1 to 1.3 - 9.9 15.7 1 16 1.4 to 1.6 - 7.7 10.8 1 11.6 1.65 to 1.95 - 6 12.9 1 12.9 2.3 to 2.7 - 5 9.1 1 9.5 3.0 to 3.6 - 4 12.5 1 13 http://onsemi.com 5 Unit ns ns ns ns ns ns NL17SG373 AC ELECTRICAL CHARACTERISTICS (Input tr = tf = 3.0 ns) TA = -555C to +1255C TA = 25 5C Symbol Parameter CIN Input Capacitance CO Output Capacitance CPD Power dissipation Capacitance (Note 5) Min Typ Max Min Max Unit 0 to 3.6 1.5 - - - pF 0 3 - - - pF VCC (V) Test Condition VO = GND f =10 MHz; VI = GND to VCC 0.9 - 1.6 - - 1.1 to 1.3 - 1.7 - - 1.4 to 1.6 - 1.8 - - 1.65 to 1.95 - 1.9 - - 2.3 to 2.7 - 2.2 - - 3.0 to 3.6 - 2.7 - - pF 5. CPD is defined as the value of the internal equivalent capacitance which is calculated from the dynamic operating current consumption without load. Average operating current can be obtained by the equation ICC(OPR) = CPD * VCC * fin + ICC. CPD is used to determine the no-load dynamic power consumption: PD = CPD * VCC2 * fin + ICC * VCC. TIMING REQUIREMENTS (Input tr = tf = 3.0 ns; CL = 5 pF, 10 pF, 15 pF and 20 pF) TA = -555C to +1255C TA = 25 5C Symbol tW tSU tH Parameter Pulse Width, LE Set-Up Time, D to LE Hold Time D to LE Test Condition High High or Low High or Low VCC (V) Min Typ Max Min Max 0.9 - 4.0 - - - 1.1 to 1.3 - 0.7 - 2.1 - 1.4 to 1.6 - 0.5 - 1.3 - 1.65 to 1.95 - 0.4 - 1.0 - 2.3 to 2.7 - 0.3 - 0.8 - 3.0 to 3.6 - 0.2 - 0.8 - 0.9 - 2.1 - - - 1.1 to 1.3 - 0.5 - 2.7 - 1.4 to 1.6 - 0.3 - 1.5 - 1.65 to 1.95 - 0.3 - 1.2 - 2.3 to 2.7 - 0.2 - 0.9 - 3.0 to 3.6 - 0.2 - 0.7 - 0.9 - -2.8 - - - 1.1 to 1.3 - -0.7 - -0.1 - 1.4 to 1.6 - -0.4 - -0.1 - 1.65 to 1.95 - -0.4 - 0 - 2.3 to 2.7 - -0.3 - 0.2 - 3.0 to 3.6 - -0.4 - 0.3 - http://onsemi.com 6 Unit ns ns ns NL17SG373 Figure 3. Test Circuit Logic levels: VOL and VOH are typical output voltage levels that occur with the output load. Figure 4. tPLH, tPHL Waveforms (D to Q) Logic levels: VOL and VOH are typical output voltage levels that occur with the output load. Figure 5. tPLH, tPHL, tW Waveforms (LE to Q) http://onsemi.com 7 NL17SG373 Logic levels: VOL and VOH are typical output voltage levels that occur with the output load. Figure 6. tSU, tH Waveforms (D to LE) MEASUREMENT POINTS FOR FIGURES 4, 5 AND 6 Supply Voltage Input Output VCC VM VI tr = tf VM 0.9 V to 3.6 V 0.5 x VCC VCC 3.0 ns 0.5 x VCC Logic levels: VOL and VOH are typical output voltage levels that occur with the output load. Figure 7. tPLZ, tPHZ, tPZH, tPZL Waveforms (OE to Q) MEASUREMENT POINTS FOR FIGURE 7 Supply Voltage Input Output VCC VM VI tr = tf VM VX VY 0.9 V 0.5 x VCC VCC 3.0 ns 0.5 x VCC VOL + 0.1 V VOH - 0.1 V 1.1 V to 1.3 V 0.5 x VCC VCC 3.0 ns 0.5 x VCC VOL + 0.1 V VOH - 0.1 V 1.4 V to 1.6 V 0.5 x VCC VCC 3.0 ns 0.5 x VCC VOL + 0.1 V VOH - 0.1 V 1.65 V to 1.95 V 0.5 x VCC VCC 3.0 ns 0.5 x VCC VOL + 0.15 V VOH - 0.15 V 2.3 V to 2.7 V 0.5 x VCC VCC 3.0 ns 0.5 x VCC VOL + 0.15 V VOH - 0.15 V 3.0 V to 3.6 V 0.5 x VCC VCC 3.0 ns 0.5 x VCC VOL + 0.3 V VOH - 0.3 V http://onsemi.com 8 NL17SG373 ORDERING INFORMATION Device NL17SG373DFT2G Package Shipping SC-88 / SOT-363 / SC-70-6 (Pb-Free) 3000 / Tape & Reel For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 9 NL17SG373 PACKAGE DIMENSIONS SC-88/SC70-6/SOT-363 CASE 419B-02 ISSUE Y 2X aaa H D D H A D 6 5 GAGE PLANE 4 L L2 E1 E 1 2 DETAIL A 3 aaa C 2X bbb H D 2X 3 TIPS NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSIONS D AND E1 DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. MOLD FLASH, PROTRUSIONS, OR GATE BURRS SHALL NOT EXCEED 0.20 PER END. 4. DIMENSIONS D AND E1 AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY AND DATUM H. 5. DATUMS A AND B ARE DETERMINED AT DATUM H. 6. DIMENSIONS b AND c APPLY TO THE FLAT SECTION OF THE LEAD BETWEEN 0.08 AND 0.15 FROM THE TIP. 7. DIMENSION b DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 TOTAL IN EXCESS OF DIMENSION b AT MAXIMUM MATERIAL CONDITION. THE DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OF THE FOOT. e B 6X DIM A A1 A2 b C D E E1 e L L2 aaa bbb ccc ddd b ddd TOP VIEW M A2 C A-B D DETAIL A A 6X ccc C A1 C SIDE VIEW SEATING PLANE c MILLIMETERS MIN NOM MAX --- --- 1.10 0.00 --- 0.10 0.70 0.90 1.00 0.15 0.20 0.25 0.08 0.15 0.22 1.80 2.00 2.20 2.00 2.10 2.20 1.15 1.25 1.35 0.65 BSC 0.26 0.36 0.46 0.15 BSC 0.15 0.30 0.10 0.10 INCHES NOM MAX --- 0.043 --- 0.004 0.035 0.039 0.008 0.010 0.006 0.009 0.078 0.086 0.082 0.086 0.049 0.053 0.026 BSC 0.010 0.014 0.018 0.006 BSC 0.006 0.012 0.004 0.004 MIN --- 0.000 0.027 0.006 0.003 0.070 0.078 0.045 END VIEW RECOMMENDED SOLDERING FOOTPRINT* 6X 6X 0.30 0.66 2.50 0.65 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. MiniGate is a trademark of Semiconductor Components Industries, LLC (SCILLC). ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5817-1050 http://onsemi.com 10 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NL17SG373/D