SKY77149 - Skyworks Solutions, Inc.

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com

103062B • Skyworks Proprietary and Confidential Information. • Products and product information are subject to change without notice. • November 6, 2006 1

DATA SHEET

SKY77149 PA Module for CDMA / PCS (1850–1910 MHz)

Applications

• Personal Communications

Services (PCS)

• Wireless Local Loop (WLL)

Features

• Low voltage positive bias

supply

- 3.2 V to 4.2 V

• Low VREF

- 2.85 V, nominal

• Low IREF

- less than 1 mA

• Good linearity

• High efficiency

• Large dynamic range

• 8-pin package

- 3 x 3 x 1.2 mm

• Power down control

• Dynamic bias control

• InGaP

• IS95/CDMA2000/EVDO

• Full U.S. PCS coverage

Skyworks offers lead

(Pb)-free "environmentally

friendly" packaging

that is RoHS compliant

(European Parliament

for the Restriction of

Hazardous Substances).

The SKY77149 System Smart™ Power Amplifier Module (PAM) is a fully matched 8-pin surface

mount module developed for Code Division Multiple Access (CDMA) / Personal Communications

Service (PCS) and Wireless Local Loop (WLL) applications. This small and efficient module packs full

1850–1910 MHz bandwidth coverage into a single compact package. The SKY77149 meets the

stringent spectral linearity requirements of Code Division Multiple Access (CDMA) PCS transmission,

with high power added efficiency for power output of up to 28 dBm. A low current pin (VCONT) is

provided to improve efficiency for the low RF power range of operation.

The single Gallium Arsenide (GaAs) Microwave Monolithic Integrated Circuit (MMIC) contains all active

circuitry in the module. The MMIC contains on-board bias circuitry, as well as input and interstage

matching circuits. The output match is realized off-chip within the module package to optimize

efficiency and power performance into a 50-ohm load. This device is manufactured with Skyworks’

GaAs Heterojunction Bipolar Transistor (HBT) process that provides for all positive voltage DC supply

operation while maintaining high efficiency and good linearity. Primary bias to the SKY77149 is

supplied directly from a three-cell Ni-Cd, a single-cell Li-Ion, or other suitable battery with an output

in the 3.2 to 4.2 volt range. Power down is accomplished by setting the voltage on the low current

reference pin to zero volts. No external supply side switch is needed as typical “off” leakage is a few

microamperes with full primary voltage supplied from the battery.

MMIC MODULE

(6) RF_OUT

VCC1 (4)

VCC2 (5)

VREF (1)

GND (7, 8)

RF_IN (3) DA

Input

Match PA Output

Match

VCONT (2)

Driver

Stage Bias

Power

Stage Bias

Inter-Stage

Match

103062_001

Figure 1. Functional Block Diagram

DATA SHEET • SKY77149 PA MODULE FOR CDMA / PCS (1850–1910 MHz)

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com

2 November 6, 2006 • Skyworks Proprietary and Confidential Information. • Products and product information are subject to change without notice. • 103062B

Electrical Specifications

The following tables list the electrical characteristics of the

SKY77149 Power Amplifier. Table 1 lists the absolute maximum

ratings, while Table 2 shows the recommended operating

conditions to achieve the performance characteristics listed in

Table 4. Table 3 presents a truth table for the power settings.

Table 1. Absolute Maximum Ratings 1

Parameter Symbol Minimum Nominal Maximum Unit

RF Input Power PIN — 0 5 dBm

Supply Voltage VCC — 3.4 6.0 Volts

Reference Voltage VREF — 2.85 3.0 Volts

Control Voltage VCONT — 1.25 3.0 Volts

Operating TC –30 25 +110

Case Temperature 2

Storage TSTG –55 — +125

°C

1 No damage assuming only one parameter is set at limit at a time with all other parameters set at nominal value.

2 Case Operating Temperature refers to the temperature of the GROUND PAD at the underside of the package.

Table 2. Recommended Operating Conditions

Parameter Symbol Minimum Nominal Maximum Unit

Power Output PO — — 28.0 dBm

Operating Frequency FO 1850.0 1880.0 1910.0 MHz

Supply Voltage VCC 3.2 3.4 4.2 Volts

Reference Voltage VREF 2.75 2.85 2.95 Volts

Control voltage VCONT 1.0 1.25 2.0 Volts

Case Operating Temperature TC –30 +25 +85 °C

Table 3. Power Range Truth Table 1

Power Setting VREF VCONT Output Power

High Power 2.85 V 2.0 V 28 dBm

Low Power 2.85 V < 1.3 V ≤ 0 dBm

Shut Down 0.0 V 0.0 V —

1 In the output power range between –10 dBm and +28 dBm, VCONT can be continuously adjusted to minimize current consumption while

meeting required linearity specification.

PA MODULE FOR CDMA / PCS (1850–1910 MHz) DATA SHEET • SKY77149

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com

103062B • Skyworks Proprietary and Confidential Information. • Products and product information are subject to change without notice. • November 6, 2006 3

Table 4. Electrical Specifications for CDMA Nominal Operating Conditions 1

Characteristics Symbol Condition Minimum Typical Maximum Unit

GLOW VCONT ≤ 1.3 V

PO < 0 dBm 19 22 23

GMID 1.3 V ≤ VCONT < 2.0 V

PO = 16 dBm 23 26 28

Gain conditions

GHIGH VCONT = 2.0 V

PO = 28 dBm 26 28 30

Gain Sensitivity GSEN All conditions fixed, except VCONT 5 8 15 dB/Volt

PAELOW PO = 0 dBm 0.5 0.7

Power Added Efficiency for Optimal VCONT Setting (VCC = 3.4 V)

PAEHIGH PO = 28 dBm 37.0 40.0

ICC_LOW PO = 0 dBm 40 60

Total Supply current for Optimal VCONT Setting

ICC_HIGH PO = 28 dBm 450 500

IQ_LOW VCONT = 1.25 V 15 35 47

Quiescent current

IQ_HIGH VCONT = 2.0 V 65 95 130

Reference Current IREF 0.5 1.5 mA

Control Current ICTRL VCONT = 2.0 V 100 250 µA

Total Supply current in Power-down Mode IPD VCC = 3.4 V

VREF = 0 V 2.0 5.0 µA

ACP1_LOW VCONT ≤ 1.3 V

PO ≤ 0 dBm –63.0 –50.0

1.25 MHz offset

ACP1_HIGH PO ≤ 28 dBm –50.0 –48.0

ACP2_LOW VCONT ≤ 1.3 V

PO ≤ 0 dBm –80.0 –60.0

Adjacent Channel Power for Optimal VCONT Setting 2,3

1.98 MHz offset

ACP2_HIGH PO ≤ 28 dBm –55.0 –53.5

dBc

Second FO2 –56.0 –35.0

Harmonic Suppression

Third FO3

PO ≤ 28 dBm

–45.0 –40.0

dBc

Noise Power in RX Band 1930-1990 MHz RxBN PO ≤ 28 dBm –138.0 dBm/Hz

Noise Figure NF — 4.0 dB

Input Voltage Standing Wave Ratio (VSWR) VSWR — — 2.5:1 —

Stability (Spurious output) S 5:1 VSWR

All phases — –70.0 dBc

PO ≤ 28 dBm 10:1 —

Ruggedness 4 Ru

PO = 29 dBm 5:1 — —

VSWR

DC TONDC 40

Turn On Time 5

RF TONRF 5

µs

DC TOFFDC 40

Turn Off Time 5

RF TOFFRF 5

µs

1 Per Table 2 over dynamic range up to 28 dBm output power, unless otherwise specified

2 ACP is specified per IS95 as the ratio of the total in-band power (1.23 MHz BW) to adjacent power in a 30 kHz BW.

3 For CDMA2000 test configured as [PCH @ –3.75 dB, DCCH–9600 bps @ 0 dB; SCHO–9600 bps @ 0 dB] and other test configurations that yield a peak-to-average up to 4.5 dB for CCDF = 1%,

up to 1. dB power back off from the maximum listed for IS95 may be required to meet specified maximum ACP performance under worst-case conditions.

4 All phases, time = 10 seconds; VCC = 4.2 V; Freq. = 1850 MHz, 1880 MHz, 1910 MHz; TCASE = –30 °C, +25 °C, +85 °C; PO set using 50 Ω load, PIN held constant during mismatch.

5 TONDC is time required to reach stable quiescent bias (±10%) after VREF is switched high.

TOFFDC is time required for battery to decrease to < 100 µA after VREF is switched low.

After ICQ is stable, The TONRF is time to reach final output power (±1 dB) once RF input is applied.

TOFFRF is time required for PO to drop 30 dB once RF input is removed.

DATA SHEET • SKY77149 PA MODULE FOR CDMA / PCS (1850–1910 MHz)

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com

4 November 6, 2006 • Skyworks Proprietary and Confidential Information. • Products and product information are subject to change without notice. • 103062B

Characterization Data

The following graphs illustrate the characteristics of a typical

SKY77149 power amplifier designed for operation in the cellular

frequency band (824–849 MHz). This amplifier was selected by

characterizing a group of devices and then selecting a part with

average electrical performance for both nominal and the full

range of recommended operating conditions, including worst case

limits. Figure 2 through 8 illustrate the digital signal

characteristics of the SKY77149. Shown are power sweep

characteristics for key performance parameters, over temperature

and frequency, up to 28.5 dBm output power. The data was taken

up to and including 8 dBm output power with the bias mode

control pad setting of VCONT = 1.25 volts and from 10 dBm to

16 dBm output power with the bias mode control pad setting of

VCONT = 1.55 V. Beyond 16 dBm output power, VCONT was set

to 2.0 V.

0246810121416

18 20 22 24 26 28 30

OUT

(dBm)

Gain (dB)

103062_002

CONT

= 2.0 V

CONT

= 1.55 V

CONT

= 1.25 V

Figure 2. Gain vs. Output Power

Legend

1880 MHz @ –30 ˚C

1850 MHz @ –30 ˚C

1910 MHz @ –30 ˚C

1850 MHz @ +25 ˚C

1880 MHz @ +25

˚C

1910 MHz @ +25

˚C

1880 MHz @ +85 ˚C

1850 MHz @ +85 ˚C

1910 MHz @ +85 ˚C

PA MODULE FOR CDMA / PCS (1850–1910 MHz) DATA SHEET • SKY77149

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com

103062B • Skyworks Proprietary and Confidential Information. • Products and product information are subject to change without notice. • November 6, 2006 5

100

200

300

400

500

600

700

800

024681012141618202224262830

OUT

(dBm)

ICC (mA)

103062_003

CONT

= 2.0 V

CONT

= 1.55 V

CONT

= 1.25 V

Figure 3. Supply Current vs. Output Power

024681012141618202224262830

OUT

(dBm)

PAE (%)

CONT

= 2.0 V

CONT

= 1.55 V

CONT

= 1.25 V

103062_004

Figure 4. Power Added Efficiency vs. Output Power

Legend

1880 MHz @ –30 ˚C

1850 MHz @ –30 ˚C

1910 MHz @ –30 ˚C

1850 MHz @ +25 ˚C

1880 MHz @ +25

˚C

1910 MHz @ +25

˚C

1880 MHz @ +85 ˚C

1850 MHz @ +85 ˚C

1910 MHz @ +85 ˚C

DATA SHEET • SKY77149 PA MODULE FOR CDMA / PCS (1850–1910 MHz)

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com

6 November 6, 2006 • Skyworks Proprietary and Confidential Information. • Products and product information are subject to change without notice. • 103062B

0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30

POUT (dBm)

ACPR1

CONT

= 2.0 VV

CONT

= 1.55 V

CONT

= 1.25 V

103062_005

Figure 5. Adjacent Channel Power Ratio 1 vs. Output Power

103062_006

CONT

= 2.0 VV

CONT

= 1.55 VV

CONT

= 1.25 V

024681012141618202224262830

OUT

(dBm)

ACPR2 (dB)

Figure 6. Adjacent Channel Power Ratio 2 vs. Output Power

Legend

1880 MHz @ –30 ˚C

1850 MHz @ –30 ˚C

1910 MHz @ –30 ˚C

1850 MHz @ +25 ˚C

1880 MHz @ +25

˚C

1910 MHz @ +25

˚C

1880 MHz @ +85 ˚C

1850 MHz @ +85 ˚C

1910 MHz @ +85 ˚C

PA MODULE FOR CDMA / PCS (1850–1910 MHz) DATA SHEET • SKY77149

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com

103062B • Skyworks Proprietary and Confidential Information. • Products and product information are subject to change without notice. • November 6, 2006 7

024681012141618202224262830

OUT

(dBm)

(dB)

CONT

= 2.0 VV

CONT

= 1.55 VV

CONT

= 1.25 V

103062_007

Figure 7. Second Harmonic vs. Output Power

024681012141618202224262830

OUT

(dBm)

(dBc)

CONT

= 2.0 VV

CONT

= 1.55 VV

CONT

= 1.25 V

103062_008

Figure 8. Third Harmonic vs. Output Power

Legend

1880 MHz @ –30 ˚C

1850 MHz @ –30 ˚C

1910 MHz @ –30 ˚C

1850 MHz @ +25 ˚C

1880 MHz @ +25

˚C

1910 MHz @ +25

˚C

1880 MHz @ +85 ˚C

1850 MHz @ +85 ˚C

1910 MHz @ +85 ˚C

DATA SHEET • SKY77149 PA MODULE FOR CDMA / PCS (1850–1910 MHz)

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com

8 November 6, 2006 • Skyworks Proprietary and Confidential Information. • Products and product information are subject to change without notice. • 103062B

Evaluation Board Description

The evaluation board is a platform for testing and interfacing

design circuitry. To accommodate the interface testing of the

SKY77149, the evaluation board schematic and diagrams are

included for preliminary analysis and design. Figure 9 shows the

basic schematic of the board for the 1850 MHz to 1910 MHz

range.

1000 pF

330

330 pF

VCC1

VREF

GND

VCC1 VCC2

RF_IN

VCONT

RF_OUT

103062_009

RF_IN

CONT

VREF

RF_OUT

VCC2

1000 pF

10 µF

Place caps at closest proximity to PA module with the capacitor grounds directly connected to the PAM grounds.

1GND

Figure 9. Evaluation Board Schematic

J2 J1

GND

VCONT

GND

VREF

GND

VCC1

VCC2

GND

SKYWORKS

SOLUTIONS, INC.

EN17 - D435 - 001

REV. 00 06/11/03

COMPONENTS

C1 1000 pF

C2 330 pF

C3 1000 pF

C4 10 µF

C5 1000 pF

C6 330 pF

RF_OUT

RF_IN

103062_010

Figure 10. Evaluation Board Assembly Diagram

PA MODULE FOR CDMA / PCS (1850–1910 MHz) DATA SHEET • SKY77149

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com

103062B • Skyworks Proprietary and Confidential Information. • Products and product information are subject to change without notice. • November 6, 2006 9

Package Dimensions and Pin Descriptions

The SKY77149 is a multi-layer laminate base, overmold

encapsulated modular package designed for surface mount solder

attachment to a printed circuit board. Figure 11 is a mechanical

drawing of the pad layout for this package and Figure 12 is a PCB

Symbol diagram of the 3x3 mm SKY77149. Figure 13 shows the

pin names and the pin numbering convention, which starts with

pin 1 in the upper left and increments counter-clockwise around

the package. Figure 14 illustrates typical case markings.

ALL DIMENSIONS ARE IN MILLIMETERS.

PIN 1 INDICATOR

2X 1.325 2X 0.7

4X 0.4

(1.35)

METAL PAD

PIN 1

(1.35)

4X 1.2

0.1

1.15 ±0.1

0.1 ABC

0.15 ABC

SOLDER MASK OPENING

4X R0.2

SOLDER MASK EDGES

METAL PAD EDGES

0.1 ABC

0.1

0.1 2X 0.4

0.05 ABC

DETAIL

PAD

SCALE: 2X

1X THIS ROTATION

1X ROTATED 90˚ CCW

1X ROTATED 90˚ CW

1X ROTATED 180˚

DETAIL

PAD

SCALE: 2X

2X THIS ROTATION

2X ROTATED 180˚

0.1 ABC

2X 0.4

0.1

ABC

0.05

103062_011

SIDE VIEW

TOP VIEW

BOTTOM VIEW

Figure 11. SKY77149 Package Drawing

DATA SHEET • SKY77149 PA MODULE FOR CDMA / PCS (1850–1910 MHz)

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com

10 November 6, 2006 • Skyworks Proprietary and Confidential Information. • Products and product information are subject to change without notice. • 103062B

PCB SYMBOL FOR 3.0 x 3.0 mm PACKAGE CX77149 & CX77154 SPECIFIC

2.3

1.2

0.6

0.4

0.8 TYP

3.2

STENCIL APERTURE

TOP VIEW

APPROACH 1

0.6 COMMON GROUND

PAD

0.4

0.8 TYP

0.25

METALLIZATION

TOP VIEW

3.2

Thermal Via Array

Ø0.3 mm on 0.5 mm Pitch

Additional Vias will improve

thermal performance.

NOTE: Thermal Vias Should be

Tented and Filled with Solder Mask

30-35 µm Cu Plating Recommended.

0.6 1.3

0.7

0.15

3.2

0.8 TYP

0.4

STENCIL APERTURE

TOP VIEW

APPROACH 2

0.7

0.5

0.05 ALL AROUND

0.8 TYP

1.3

3.3

2.55

4 X R0.5

SOLDER MASK OPENING

TOP VIEW

COMPONENT

OUTLINE

COMPONENT

OUTLINE

COMPONENT

OUTLINE

COMPONENT

OUTLINE

All dimensions are in millimeters. 103062_012

Figure 12. Phone PCB Layout Footprint Diagram for 3 x 3 mm, 8-Pin Package – SKY77149

PA MODULE FOR CDMA / PCS (1850–1910 MHz) DATA SHEET • SKY77149

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com

103062B • Skyworks Proprietary and Confidential Information. • Products and product information are subject to change without notice. • November 6, 2006 11

VREF

VCONT

RF_IN

VCC1 VCC2

RF_OUT

GND

103062_013

Pad layout as seen from top view looking through the package.

GROUND PAD is package underside.

GROUND PAD

Figure 13. SKY77149 Pin Names and Configuration (Top View)

103062_014

77149-N

XXXXX.X

YYWW MX

Revision

Number

Pin 1

Identifier

Lot

Number

Country

Code

Part

Number

Year of

Manufacture

Week

Package

Sealed

Figure 14. Typical Case Markings

Package and Handling Information

Because of its sensitivity to moisture absorption, this device

package is baked and vacuum-packed prior to shipment.

Instructions on the shipping container label must be followed

regarding exposure to moisture after the container seal is broken,

otherwise, problems related to moisture absorption may occur

when the part is subjected to high temperature during solder

assembly.

The SKY77149 is capable of withstanding an MSL3/250 °C solder

reflow. Care must be taken when attaching this product, whether

it is done manually or in a production solder reflow environment.

If the part is attached in a reflow oven, the temperature ramp rate

should not exceed 3 °C per second; maximum temperature

should not exceed 250 °C. If the part is manually attached,

precaution should be taken to insure that the part is not subjected

to temperatures exceeding 250 °C for more than 10 seconds. For

details on attachment techniques, precautions, and handling

procedures recommended by Skyworks, please refer to Skyworks

Application Note: PCB Design and SMT Assembly/Rework,

Document Number 101752. Additional information on standard

SMT reflow profiles can also be found in the JEDEC Standard

J-STD–020.

Production quantities of this product are shipped in the standard

tape-and-reel format. For packaging details, refer to Skyworks

Application Note: Tape and Reel Information – RF Modules,

Document Number 101568.

Electrostatic Discharge Sensitivity

The SKY77149 is a Class 2 device. Figure 15 lists the Electrostatic

Discharge (ESD) immunity level for each non-ground pin of the

SKY77149 product. The numbers in Figure 15 specify the ESD

threshold level for each pin where the I-V curve between the pin

and ground starts to show degradation.

The ESD testing was performed in compliance with

MIL-STD-883E Method 3015.7 using the Human Body Model. If

ESD damage threshold magnitude is found to consistently exceed

2000 volts on a given pin, this so is indicated. If ESD damage

threshold below 2000 volts is measured for either polarity,

numbers are indicated that represent worst case values observed

in product characterization.

Various failure criteria can be utilized when performing ESD

testing. Many vendors employ relaxed ESD failure standards,

which fail devices only after “the pin fails the electrical

specification limits” or “the pin becomes completely non-

functional”. Skyworks employs most stringent criteria and fails

devices as soon as the pin begins to show any degradation on a

curve tracer.

103062_015

VREF

> + 2 kV

< – 2 kV

RF_IN

> + 2 kV

< – 2 kV

VCC1

> + 2 kV

< – 2 kV

RF_OUT

> + 2 kV

< – 2 kV

VCC2

> + 2 kV

< – 2 kV

VCONT

> + 2 kV

< – 2 kV

GROUND PAD

Pad layout as seen from top view looking through the package.

GND

Figure 15. ESD Sensitivity Areas (Top View)

DATA SHEET • SKY77149 PA MODULE FOR CDMA / PCS (1850–1910 MHz)

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com

12 November 6, 2006 • Skyworks Proprietary and Confidential Information. • Products and product information are subject to change without notice. • 103062B

To avoid ESD damage, both latent and visible, it is very important

that the product assembly and test areas follow the Class-1 ESD

handling precautions listed below.

• Personnel Grounding • Facility

- Wrist Straps - Relative Humidity Control and Air Ionizers

- Conductive Smocks, Gloves and Finger Cots - Dissipative Floors (less than 109 Ω to GND)

- Antistatic ID Badges

• Protective Workstation • Protective Packaging and Transportation

- Dissipative Table Top - Bags and Pouches (Faraday Shield)

- Protective Test Equipment (Properly Grounded) - Protective Tote Boxes (Conductive Static Shielding)

- Grounded Tip Soldering Irons - Protective Trays

- Solder Conductive Suckers - Grounded Carts

- Static Sensors - Protective Work Order Holders

Ordering Information

Model Number Manufacturing Part

Number Product Revision Package Operating Temperature

SKY77149 SKY77149 3x3LM–10 –30 °C to +85 °C

Revision History

Revision Level Date Description

A May 8, 2006 Initial Release

B November 6, 2006 Revise: Table 4

References

Application Note: PCB Design and SMT Assembly/Rework, Document Number 101752.

Application Note: Tape and Reel Information – RF Modules, Document Number 101568

Standard SMT Reflow Profiles: JEDEC Standard J–STD–020

Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products. These materials are provided by Skyworks as a service to its customers and may be

used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials. Skyworks may make changes to its documentation, products,

specifications and product descriptions at any time, without notice. Skyworks makes no commitment to update the information and shall have no responsibility whatsoever for conflicts,

incompatibilities, or other difficulties arising from future changes to its documentation, products, specifications and product descriptions.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by or under this document. Except as may be provided in Skyworks Terms and Conditions of

Sale for such products, Skyworks assumes no liability whatsoever in association with its documentation, products, specifications and product descriptions.

THESE MATERIALS ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED OR OTHERWISE, RELATING TO SALE AND/OR USE OF SKYWORKS PRODUCTS

INCLUDING WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER

INTELLECTUAL PROPERTY RIGHT. SKYWORKS FURTHER DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN

THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST

REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THESE MATERIALS WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH

DAMAGE.

Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications. Skyworks customers using or selling Skyworks products for use in such applications do so at their

own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale.

The following are trademarks of Skyworks Solutions, Inc.: Skyworks®, the Skyworks logo, and Breakthrough Simplicity®. Product names or services listed in this publication are for identification

purposes only, and may be trademarks of Skyworks or other third parties. Third-party brands and names are the property of their respective owners. Additional information, posted at