DATA SHEET SKY77149 PA Module for CDMA / PCS (1850-1910 MHz) Applications * Personal Communications Services (PCS) * Wireless Local Loop (WLL) Features * Low voltage positive bias supply - 3.2 V to 4.2 V * Low VREF - 2.85 V, nominal * Low IREF - less than 1 mA * Good linearity * High efficiency * Large dynamic range * 8-pin package - 3 x 3 x 1.2 mm * Power down control The SKY77149 System SmartTM Power Amplifier Module (PAM) is a fully matched 8-pin surface mount module developed for Code Division Multiple Access (CDMA) / Personal Communications Service (PCS) and Wireless Local Loop (WLL) applications. This small and efficient module packs full 1850-1910 MHz bandwidth coverage into a single compact package. The SKY77149 meets the stringent spectral linearity requirements of Code Division Multiple Access (CDMA) PCS transmission, with high power added efficiency for power output of up to 28 dBm. A low current pin (VCONT) is provided to improve efficiency for the low RF power range of operation. The single Gallium Arsenide (GaAs) Microwave Monolithic Integrated Circuit (MMIC) contains all active circuitry in the module. The MMIC contains on-board bias circuitry, as well as input and interstage matching circuits. The output match is realized off-chip within the module package to optimize efficiency and power performance into a 50-ohm load. This device is manufactured with Skyworks' GaAs Heterojunction Bipolar Transistor (HBT) process that provides for all positive voltage DC supply operation while maintaining high efficiency and good linearity. Primary bias to the SKY77149 is supplied directly from a three-cell Ni-Cd, a single-cell Li-Ion, or other suitable battery with an output in the 3.2 to 4.2 volt range. Power down is accomplished by setting the voltage on the low current reference pin to zero volts. No external supply side switch is needed as typical "off" leakage is a few microamperes with full primary voltage supplied from the battery. * Dynamic bias control * InGaP * IS95/CDMA2000/EVDO * Full U.S. PCS coverage MODULE MMIC VREF (1) Skyworks offers lead (Pb)-free "environmentally friendly" packaging that is RoHS compliant (European Parliament for the Restriction of Hazardous Substances). VCONT (2) VCC2 (5) Power Stage Bias Driver Stage Bias VCC1 (4) RF_IN (3) Input Match DA Inter-Stage Match PA Output Match (6) RF_OUT GND (7, 8) 103062_001 Figure 1. Functional Block Diagram Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 103062B * Skyworks Proprietary and Confidential Information. * Products and product information are subject to change without notice. * November 6, 2006 1 DATA SHEET * SKY77149 PA MODULE FOR CDMA / PCS (1850-1910 MHz) Electrical Specifications The following tables list the electrical characteristics of the SKY77149 Power Amplifier. Table 1 lists the absolute maximum ratings, while Table 2 shows the recommended operating conditions to achieve the performance characteristics listed in Table 4. Table 3 presents a truth table for the power settings. Table 1. Absolute Maximum Ratings 1 Parameter Symbol Minimum Nominal Maximum Unit RF Input Power PIN -- 0 5 dBm Supply Voltage VCC -- 3.4 6.0 Volts Reference Voltage VREF -- 2.85 3.0 Volts Control Voltage VCONT -- 1.25 3.0 Volts Operating TC -30 25 +110 Storage -55 -- +125 Case Temperature 2 TSTG 1 No damage assuming only one parameter is set at limit at a time with all other parameters set at nominal value. 2 Case Operating Temperature refers to the temperature of the GROUND PAD at the underside of the package. C Table 2. Recommended Operating Conditions Parameter Minimum Nominal Maximum Unit PO -- -- 28.0 dBm Operating Frequency FO 1850.0 1880.0 1910.0 MHz Supply Voltage VCC 3.2 3.4 4.2 Volts Reference Voltage VREF 2.75 2.85 2.95 Volts Control voltage VCONT 1.0 1.25 2.0 Volts Case Operating Temperature TC -30 +25 +85 C Power Output Symbol Table 3. Power Range Truth Table 1 VREF VCONT Output Power High Power Power Setting 2.85 V 2.0 V 28 dBm Low Power 2.85 V < 1.3 V 0 dBm Shut Down 0.0 V 0.0 V -- 1 In the output power range between -10 dBm and +28 dBm, VCONT can be continuously adjusted to minimize current consumption while meeting required linearity specification. Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 2 November 6, 2006 * Skyworks Proprietary and Confidential Information. * Products and product information are subject to change without notice. * 103062B PA MODULE FOR CDMA / PCS (1850-1910 MHz) DATA SHEET * SKY77149 Table 4. Electrical Specifications for CDMA Nominal Operating Conditions 1 Characteristics Symbol GLOW Gain conditions GMID GHIGH Gain Sensitivity Power Added Efficiency for Optimal VCONT Setting (VCC = 3.4 V) Total Supply current for Optimal VCONT Setting Quiescent current Condition VCONT 1.3 V PO < 0 dBm 1.3 V VCONT < 2.0 V PO = 16 dBm VCONT = 2.0 V PO = 28 dBm Minimum Typical Maximum 19 22 23 23 26 28 26 28 30 5 8 15 Unit dB GSEN All conditions fixed, except VCONT dB/Volt PAELOW PO = 0 dBm 0.5 0.7 PAEHIGH PO = 28 dBm 37.0 40.0 ICC_LOW PO = 0 dBm 40 60 ICC_HIGH PO = 28 dBm 450 500 IQ_LOW VCONT = 1.25 V 15 35 47 IQ_HIGH VCONT = 2.0 V 65 95 130 0.5 1.5 mA % mA mA Reference Current IREF Control Current ICTRL VCONT = 2.0 V 100 250 A IPD VCC = 3.4 V VREF = 0 V 2.0 5.0 A ACP1_LOW VCONT 1.3 V PO 0 dBm -63.0 -50.0 ACP1_HIGH PO 28 dBm -50.0 -48.0 VCONT 1.3 V PO 0 dBm -80.0 -60.0 ACP2_HIGH PO 28 dBm -55.0 -53.5 Second FO2 -56.0 -35.0 Third FO3 -45.0 -40.0 Total Supply current in Power-down Mode 1.25 MHz offset Adjacent Channel Power for Optimal VCONT Setting 2,3 ACP2_LOW 1.98 MHz offset Harmonic Suppression dBc PO 28 dBm dBc Noise Power in RX Band 1930-1990 MHz RxBN PO 28 dBm -138.0 dBm/Hz Noise Figure NF -- 4.0 dB Input Voltage Standing Wave Ratio (VSWR) VSWR -- -- 2.5:1 -- Stability (Spurious output) S 5:1 VSWR All phases -- -70.0 dBc Ruggedness 4 Ru Turn On Time 5 Turn Off Time 5 PO 28 dBm 10:1 -- PO = 29 dBm 5:1 -- DC TONDC 40 RF TONRF 5 DC TOFFDC 40 RF TOFFRF 5 VSWR -- s s 1 Per Table 2 over dynamic range up to 28 dBm output power, unless otherwise specified 2 ACP is specified per IS95 as the ratio of the total in-band power (1.23 MHz BW) to adjacent power in a 30 kHz BW. 3 For CDMA2000 test configured as [PCH @ -3.75 dB, DCCH-9600 bps @ 0 dB; SCHO-9600 bps @ 0 dB] and other test configurations that yield a peak-to-average up to 4.5 dB for CCDF = 1%, up to 1. dB power back off from the maximum listed for IS95 may be required to meet specified maximum ACP performance under worst-case conditions. 4 All phases, time = 10 seconds; VCC = 4.2 V; Freq. = 1850 MHz, 1880 MHz, 1910 MHz; TCASE = -30 C, +25 C, +85 C; PO set using 50 load, PIN held constant during mismatch. 5 TONDC is time required to reach stable quiescent bias (10%) after VREF is switched high. TOFFDC is time required for battery to decrease to < 100 A after VREF is switched low. After ICQ is stable, The TONRF is time to reach final output power (1 dB) once RF input is applied. TOFFRF is time required for PO to drop 30 dB once RF input is removed. Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 103062B * Skyworks Proprietary and Confidential Information. * Products and product information are subject to change without notice. * November 6, 2006 3 DATA SHEET * SKY77149 PA MODULE FOR CDMA / PCS (1850-1910 MHz) Characterization Data The following graphs illustrate the characteristics of a typical SKY77149 power amplifier designed for operation in the cellular frequency band (824-849 MHz). This amplifier was selected by characterizing a group of devices and then selecting a part with average electrical performance for both nominal and the full range of recommended operating conditions, including worst case limits. Figure 2 through 8 illustrate the digital signal characteristics of the SKY77149. Shown are power sweep characteristics for key performance parameters, over temperature and frequency, up to 28.5 dBm output power. The data was taken up to and including 8 dBm output power with the bias mode control pad setting of VCONT = 1.25 volts and from 10 dBm to 16 dBm output power with the bias mode control pad setting of VCONT = 1.55 V. Beyond 16 dBm output power, VCONT was set to 2.0 V. 31 29 27 Gain (dB) 25 23 VCONT = 2.0 V 21 19 VCONT = 1.55 V VCONT = 1.25 V 17 15 0 2 4 6 8 10 12 14 16 18 POUT (dBm) 20 22 24 26 28 30 103062_002 Figure 2. Gain vs. Output Power Legend 1850 MHz @ -30 C 1850 MHz @ +25 C 1850 MHz @ +85 C 1880 MHz @ -30 C 1880 MHz @ +25 C 1880 MHz @ +85 C 1910 MHz @ -30 C 1910 MHz @ +25 C 1910 MHz @ +85 C Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 4 November 6, 2006 * Skyworks Proprietary and Confidential Information. * Products and product information are subject to change without notice. * 103062B PA MODULE FOR CDMA / PCS (1850-1910 MHz) DATA SHEET * SKY77149 800 700 600 VCONT = 2.0 V ICC (mA) 500 VCONT = 1.55 V 400 VCONT = 1.25 V 300 200 100 0 0 2 4 6 8 10 12 14 16 18 POUT (dBm) 20 22 24 26 28 30 103062_003 Figure 3. Supply Current vs. Output Power 50 45 40 35 PAE (%) 30 VCONT = 2.0 V 25 20 VCONT = 1.55 V 15 VCONT = 1.25 V 10 5 0 0 2 4 6 8 10 12 14 16 18 POUT (dBm) 20 22 24 26 28 30 103062_004 Figure 4. Power Added Efficiency vs. Output Power Legend 1850 MHz @ -30 C 1850 MHz @ +25 C 1850 MHz @ +85 C 1880 MHz @ -30 C 1880 MHz @ +25 C 1880 MHz @ +85 C 1910 MHz @ -30 C 1910 MHz @ +25 C 1910 MHz @ +85 C Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 103062B * Skyworks Proprietary and Confidential Information. * Products and product information are subject to change without notice. * November 6, 2006 5 DATA SHEET * SKY77149 PA MODULE FOR CDMA / PCS (1850-1910 MHz) 65 VCONT = 1.25 V VCONT = 1.55 V VCONT = 2.0 V 60 ACPR1 55 50 45 40 35 30 0 2 4 6 8 10 12 14 16 18 POUT (dBm) 20 22 24 26 28 30 103062_005 Figure 5. Adjacent Channel Power Ratio 1 vs. Output Power 85 VCONT = 1.25 V VCONT = 1.55 V VCONT = 2.0 V 80 75 ACPR2 (dB) 70 65 60 55 50 45 40 0 2 4 6 8 10 12 14 16 18 POUT (dBm) 20 22 24 26 28 30 103062_006 Figure 6. Adjacent Channel Power Ratio 2 vs. Output Power Legend 1850 MHz @ -30 C 1850 MHz @ +25 C 1850 MHz @ +85 C 1880 MHz @ -30 C 1880 MHz @ +25 C 1880 MHz @ +85 C 1910 MHz @ -30 C 1910 MHz @ +25 C 1910 MHz @ +85 C Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 6 November 6, 2006 * Skyworks Proprietary and Confidential Information. * Products and product information are subject to change without notice. * 103062B PA MODULE FOR CDMA / PCS (1850-1910 MHz) 64 DATA SHEET * SKY77149 VCONT = 1.25 V VCONT = 1.55 V VCONT = 2.0 V 62 60 58 2F0 (dB) 56 54 52 50 48 46 44 42 40 0 2 4 6 8 10 12 14 16 18 POUT (dBm) 20 22 24 26 28 30 103062_007 Figure 7. Second Harmonic vs. Output Power 65 60 VCONT = 1.25 V VCONT = 1.55 V VCONT = 2.0 V 3F0 (dBc) 55 50 45 40 35 30 0 2 4 6 8 10 12 14 16 18 POUT (dBm) 20 22 24 26 28 30 103062_008 Figure 8. Third Harmonic vs. Output Power Legend 1850 MHz @ -30 C 1850 MHz @ +25 C 1850 MHz @ +85 C 1880 MHz @ -30 C 1880 MHz @ +25 C 1880 MHz @ +85 C 1910 MHz @ -30 C 1910 MHz @ +25 C 1910 MHz @ +85 C Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 103062B * Skyworks Proprietary and Confidential Information. * Products and product information are subject to change without notice. * November 6, 2006 7 DATA SHEET * SKY77149 PA MODULE FOR CDMA / PCS (1850-1910 MHz) Evaluation Board Description The evaluation board is a platform for testing and interfacing design circuitry. To accommodate the interface testing of the SKY77149, the evaluation board schematic and diagrams are 1 VREF included for preliminary analysis and design. Figure 9 shows the basic schematic of the board for the 1850 MHz to 1910 MHz range. VREF GND VCONT GND 8 C3 1000 pF 2 VCONT 7 C1 1000 pF RF_IN RF_OUT 3 4 VCC1 RF_IN RF_OUT VCC1 VCC2 6 5 VCC2 A C6 330 pF C2 A 330 pF C5 1000 pF C4 10 F A Place caps at closest proximity to PA module with the capacitor grounds directly connected to the PAM grounds. 103062_009 Figure 9. Evaluation Board Schematic P1 RF_IN J2 SKYWORKS SOLUTIONS, INC. J1 C1 GND GND C2 VCC1 1 U1 VCONT C3 GND C5 VCC2 C6 VREF GND C4 EN17 - D435 - 001 REV. 00 06/11/03 RF_OUT P2 COMPONENTS C1 1000 pF C2 330 pF C3 1000 pF C4 10 F C5 1000 pF C6 330 pF 103062_010 Figure 10. Evaluation Board Assembly Diagram Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 8 November 6, 2006 * Skyworks Proprietary and Confidential Information. * Products and product information are subject to change without notice. * 103062B PA MODULE FOR CDMA / PCS (1850-1910 MHz) DATA SHEET * SKY77149 Package Dimensions and Pin Descriptions The SKY77149 is a multi-layer laminate base, overmold encapsulated modular package designed for surface mount solder attachment to a printed circuit board. Figure 11 is a mechanical drawing of the pad layout for this package and Figure 12 is a PCB Symbol diagram of the 3x3 mm SKY77149. Figure 13 shows the pin names and the pin numbering convention, which starts with pin 1 in the upper left and increments counter-clockwise around the package. Figure 14 illustrates typical case markings. METAL PAD EDGES 0.05 A B C B 3 C 2X 0.4 PIN 1 INDICATOR SOLDER MASK EDGES 0.1 A B C METAL PAD EDGES 0.05 A B C 0.1 DETAIL A PAD SCALE: 2X 2X THIS ROTATION 2X ROTATED 180 0.1 0.1 3 SOLDER MASK EDGES 0.1 A B C 2X 0.4 1X 1X 1X 1X DETAIL B PAD SCALE: 2X THIS ROTATION ROTATED 90 CCW ROTATED 90 CW ROTATED 180 0.1 A B C TOP VIEW (1.35) 2X 1.325 2X 0.7 METAL PAD PIN 1 4X 0.4 (1.35) A B 4X 1.2 A 1.15 0.1 SOLDER MASK OPENING 0.1 4X R0.2 SIDE VIEW 0.15 A B C BOTTOM VIEW 103062_011 ALL DIMENSIONS ARE IN MILLIMETERS. Figure 11. SKY77149 Package Drawing Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 103062B * Skyworks Proprietary and Confidential Information. * Products and product information are subject to change without notice. * November 6, 2006 9 DATA SHEET * SKY77149 PA MODULE FOR CDMA / PCS (1850-1910 MHz) PCB SYMBOL FOR 3.0 x 3.0 mm PACKAGE CX77149 & CX77154 SPECIFIC 1.2 0.6 0.6 0.4 1.3 0.4 0.7 2.3 0.8 TYP 0.15 0.8 TYP 3.2 3.2 STENCIL APERTURE TOP VIEW APPROACH 1 COMMON GROUND PAD 0.6 COMPONENT OUTLINE COMPONENT OUTLINE COMPONENT OUTLINE COMPONENT OUTLINE STENCIL APERTURE TOP VIEW APPROACH 2 0.7 4 X R0.5 0.4 0.5 0.05 ALL AROUND 2.55 0.25 0.8 TYP 0.8 TYP 0.25 3.2 METALLIZATION Thermal Via Array O0.3 mm on 0.5 mm Pitch Additional Vias will improve thermal performance. NOTE: Thermal Vias Should be Tented and Filled with Solder Mask 30-35 m Cu Plating Recommended. 1.3 3.3 SOLDER MASK OPENING TOP VIEW TOP VIEW All dimensions are in millimeters. Figure 12. Phone PCB Layout Footprint Diagram for 3 x 3 mm, 8-Pin Package - SKY77149 Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 10 November 6, 2006 * Skyworks Proprietary and Confidential Information. * Products and product information are subject to change without notice. * 103062B 103062_012 PA MODULE FOR CDMA / PCS (1850-1910 MHz) DATA SHEET * SKY77149 VREF 1 8 GND VCONT 2 7 GND RF_IN 3 VCC1 4 GROUND PAD 6 RF_OUT 5 VCC2 Pad layout as seen from top view looking through the package. GROUND PAD is package underside. 103062_013 Figure 13. SKY77149 Pin Names and Configuration (Top View) Part Number Pin 1 Identifier Lot Number Year of Manufacture Week Package Sealed 77149-N XXXXX.X YYWW MX Revision Number Country Code 103062_014 details on attachment techniques, precautions, and handling procedures recommended by Skyworks, please refer to Skyworks Application Note: PCB Design and SMT Assembly/Rework, Document Number 101752. Additional information on standard SMT reflow profiles can also be found in the JEDEC Standard J-STD-020. Production quantities of this product are shipped in the standard tape-and-reel format. For packaging details, refer to Skyworks Application Note: Tape and Reel Information - RF Modules, Document Number 101568. Electrostatic Discharge Sensitivity The SKY77149 is a Class 2 device. Figure 15 lists the Electrostatic Discharge (ESD) immunity level for each non-ground pin of the SKY77149 product. The numbers in Figure 15 specify the ESD threshold level for each pin where the I-V curve between the pin and ground starts to show degradation. The ESD testing was performed in compliance with MIL-STD-883E Method 3015.7 using the Human Body Model. If ESD damage threshold magnitude is found to consistently exceed 2000 volts on a given pin, this so is indicated. If ESD damage threshold below 2000 volts is measured for either polarity, numbers are indicated that represent worst case values observed in product characterization. Various failure criteria can be utilized when performing ESD testing. Many vendors employ relaxed ESD failure standards, which fail devices only after "the pin fails the electrical specification limits" or "the pin becomes completely nonfunctional". Skyworks employs most stringent criteria and fails devices as soon as the pin begins to show any degradation on a curve tracer. Figure 14. Typical Case Markings Package and Handling Information Because of its sensitivity to moisture absorption, this device package is baked and vacuum-packed prior to shipment. Instructions on the shipping container label must be followed regarding exposure to moisture after the container seal is broken, otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. The SKY77149 is capable of withstanding an MSL3/250 C solder reflow. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. If the part is attached in a reflow oven, the temperature ramp rate should not exceed 3 C per second; maximum temperature should not exceed 250 C. If the part is manually attached, precaution should be taken to insure that the part is not subjected to temperatures exceeding 250 C for more than 10 seconds. For VREF > + 2 kV < - 2 kV VCONT > + 2 kV < - 2 kV RF_IN > + 2 kV < - 2 kV VCC1 > + 2 kV < - 2 kV 1 8 GND 2 7 GND 3 6 4 GROUND PAD 5 RF_OUT > + 2 kV < - 2 kV VCC2 > + 2 kV < - 2 kV Pad layout as seen from top view looking through the package. 103062_015 Figure 15. ESD Sensitivity Areas (Top View) Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 103062B * Skyworks Proprietary and Confidential Information. * Products and product information are subject to change without notice. * November 6, 2006 11 DATA SHEET * SKY77149 To avoid ESD damage, both latent and visible, it is very important that the product assembly and test areas follow the Class-1 ESD * Personnel Grounding - Wrist Straps - Conductive Smocks, Gloves and Finger Cots - Antistatic ID Badges * Protective Workstation - Dissipative Table Top - Protective Test Equipment (Properly Grounded) - Grounded Tip Soldering Irons - Solder Conductive Suckers - Static Sensors PA MODULE FOR CDMA / PCS (1850-1910 MHz) handling precautions listed below. * Facility - Relative Humidity Control and Air Ionizers - Dissipative Floors (less than 109 to GND) * Protective Packaging and Transportation - Bags and Pouches (Faraday Shield) - Protective Tote Boxes (Conductive Static Shielding) - Protective Trays - Grounded Carts - Protective Work Order Holders Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 12 November 6, 2006 * Skyworks Proprietary and Confidential Information. * Products and product information are subject to change without notice. * 103062B Ordering Information Model Number Manufacturing Part Number SKY77149 SKY77149 Product Revision Package Operating Temperature 3x3LM-10 -30 C to +85 C Revision History Revision Level Date Description A May 8, 2006 Initial Release B November 6, 2006 Revise: Table 4 References Application Note: PCB Design and SMT Assembly/Rework, Document Number 101752. Application Note: Tape and Reel Information - RF Modules, Document Number 101568 Standard SMT Reflow Profiles: JEDEC Standard J-STD-020 Copyright (c) 2003-2006, Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. ("Skyworks") products. These materials are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials. Skyworks may make changes to its documentation, products, specifications and product descriptions at any time, without notice. Skyworks makes no commitment to update the information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from future changes to its documentation, products, specifications and product descriptions. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by or under this document. Except as may be provided in Skyworks Terms and Conditions of Sale for such products, Skyworks assumes no liability whatsoever in association with its documentation, products, specifications and product descriptions. THESE MATERIALS ARE PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED OR OTHERWISE, RELATING TO SALE AND/OR USE OF SKYWORKS PRODUCTS INCLUDING WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. SKYWORKS FURTHER DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THESE MATERIALS WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. The following are trademarks of Skyworks Solutions, Inc.: Skyworks(R), the Skyworks logo, and Breakthrough Simplicity(R). Product names or services listed in this publication are for identification purposes only, and may be trademarks of Skyworks or other third parties. Third-party brands and names are the property of their respective owners. Additional information, posted at www.skyworksinc.com, is incorporated by reference.