60373899 - WAGO - Product.Network

CRCW...C e3

www.vishay.com Vishay

Revision: 02-Nov-17 1Document Number: 28773

For technical questions, contact: ff3aresistors@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Lead (Pb)-free Thick Film, Rectangular

Commodity Chip Resistors

FEATURES

• High volume product suitable for commercial

applications

• Stability (R/R  1 % for 1000 h at 70 °C)

• Lead (Pb)-free solder contacts on Ni barrier

layer

• Metal glaze on ceramic

• Material categorization: for definitions of compliance

please see www.vishay.com/doc?99912

Notes

• These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over

operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifetime

• Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material

Note

(1) The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the

printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceeded

STANDARD ELECTRICAL SPECIFICATIONS

MODEL

CASE

SIZE

INCH

CASE

SIZE

METRIC

POWER RATING

P70 °C

LIMITING

ELEMENT

VOLTAGE

MAX. V 

TEMPERATURE

COEFFICIENT

ppm/K

TOLERANCE

RESISTANCE

RANGE



E-SERIES

CRCW0402...C 0402 RR 1005M 0.063 50 ± 100 ± 1 1R0 to 10M E24; E96

± 200 ± 5 1R0 to 10M E24

Zero-Ohm-Resistor: Rmax. = 20 m, Imax. at 70 °C = 1.5 A

CRCW0603...C 0603 RR 1608M 0.10 75 ± 100 ± 1 1R0 to 10M E24; E96

± 200 ± 5 1R0 to 10M E24

Zero-Ohm-Resistor: Rmax. = 20 m, Imax. at 70 °C = 2.0 A

CRCW0805...C 0805 RR 2012M 0.125 150 ± 100 ± 1 1R0 to 10M E24; E96

± 200 ± 5 1R0 to 10M E24

Zero-Ohm-Resistor: Rmax. = 20 m, Imax. at 70 °C = 2.5 A

CRCW1206...C 1206 RR 3216M 0.25 200 ± 100 ± 1 1R0 to 10M E24; E96

± 200 ± 5 1R0 to 10M E24

Zero-Ohm-Resistor: Rmax. = 20 m, Imax. at 70 °C = 3.5 A

TECHNICAL SPECIFICATIONS

PARAMETER UNIT CRCW0402...C CRCW0603...C CRCW0805...C CRCW1206...C

Rated dissipation at 70°C (1) W 0.063 0.10 0.125 0.25

Limiting element voltage

Umax. AC/DC V 50 75 150 200

Insulation voltage Uins. (1 min) V > 75 > 100 > 200 > 300

Insulation resistance > 109

Category temperature range °C - 55 to + 155

Failure rate h-1 0.1 x 10-9

Weight/1000 pieces g 0.65 2 5.5 10

CRCW...C e3

www.vishay.com Vishay

Revision: 02-Nov-17 2Document Number: 28773

For technical questions, contact: ff3aresistors@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

DIMENSIONS

Note

(1) The rated dissipation applies only if the permitted film temperature is not exceeded. Furthermore, a high level of ambient temperature or of

power dissipation may raise the temperature of the solder joint, hence special solder alloys or board materials maybe required to maintain

the reliability of the assembly. Specified power rating above 125 °C requires dedicated heat-sink pads, which depend on board materials.

The given solder pad dimensions reflect the considerations for board design and assembly as outlined e.g. in standards IEC 61188-5-x, or

in publication IPC-7351. They do not guarantee any supposed thermal properties, particularly as these are also strongly influenced by many

other parameters. Still the given solder pad dimensions will be found adequate for most general applications

PART NUMBER AND PRODUCT DESCRIPTION

PART NUMBER: CRCW0603562RFKECC

MODEL/SIZE VALUE TOLERANCE TCR PACKAGING SPECIAL

CRCW0402

CRCW0603

CRCW0805

CRCW1206

R = decimal

K = thousand

M = million

0000 = jumper

F = ± 1.0 %

J = ± 5.0 %

Z = jumper

K = ± 100 ppm/K

N = ± 200 ppm/K

0 = jumper

EA, EB,

EC, ED,

Up to 2 digits

C = commodity

PRODUCT DESCRIPTION: CRCW0603-C 100 562R 1 % ET6 E3

CRCW0603-C 100 562R 1 % ET6 e3

MODEL TCR RESISTANCE

VALUE TOLERANCE PACKAGING LEAD (Pb)-FREE

CRCW0402-C

CRCW0603-C

CRCW0805-C

CRCW1206-C

± 200 ppm/K

± 100 ppm/K

10R = 10 

562R = 562 

10K = 10.0 k

1M = 1 M

0R0 = jumper

± 5 %

± 1 %

ET1, ET5,

ET6, ET7,

EF4

e3 = pure tin

termination

finish

PACKAGING

TYPE / SIZE CODE QUANTITY PACKAGING STYLE WIDTH PITCH PACKAGING

DIMENSIONS

CRCW0402…C ED = ET7 10 000

Paper tape acc. to

IEC 60286-3, Type 1a 8 mm

2 mm Ø 180 mm/7"

EE = EF4 50 000 Ø 330 mm/13"

CRCW0603…C

EA = ET1 5000

4 mm

Ø 180 mm/7"

EB = ET5 10 000 Ø 254 mm/10"

EC = ET6 20 000 Ø 330 mm/13"

CRCW0805…C

EA = ET1 5000

4 mm

Ø 180 mm/7"

EB = ET5 10 000 Ø 254 mm/10"

EC = ET6 20 000 Ø 330 mm/13"

CRCW1206…C

EA = ET1 5000

4 mm

Ø 180 mm/7"

EB = ET5 10 000 Ø 254 mm/10"

EC = ET6 20 000 Ø 330 mm/13"

SIZE DIMENSIONS (in millimeters) SOLDER PAD DIMENSIONS (1) (in millimeters)

REFLOW SOLDERING WAVE SOLDERING

INCH METRIC L W H T1 T2 a b l a b l

0402 1005 1.0 ± 0.10 0.5 ± 0.05 0.30 ± 0.05 0.25 ± 0.10 0.2 ± 0.1 0.4 0.6 0.5

0603 1608 1.60 ± 0.10 0.80 ± 0.10 0.45 ± 0.10 0.3 ± 0.2 0.3 ± 0.2 0.5 0.9 1.0 0.9 0.9 1.0

0805 2012 2.0 ± 0.10 1.25 ± 0.15 0.50 ± 0.10 0.35 ± 0.15 0.35 ± 0.2 0.7 1.3 1.2 0.9 1.3 1.3

1206 3216 3.05 ± 0.10 1.55 ± 0.10 0.55 + 0.10

- 0.05 0.35 ± 0.15 0.45 ± 0.2 0.9 1.7 2.0 1.1 1.7 2.3

C R C W 0 6 0 3 5 6 2 R F K E C C

CRCW...C e3

www.vishay.com Vishay

Revision: 02-Nov-17 3Document Number: 28773

For technical questions, contact: ff3aresistors@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

FUNCTIONAL PERFORMANCE

TEST PROCEDURES AND REQUIREMENTS

EN 60115-1

CLAUSE

IEC 60068-2

TEST

METHOD

TEST PROCEDURE

REQUIREMENTS PERMISSIBLE

CHANGE (R)

STABILITY

CLASS 1

OR BETTER

STABILITY

CLASS 2

OR BETTER

Stability for product types:

CRCW...C e3 1  to 10 M1  to 10 M

4.5 - Resistance - ± 1 % ± 5 %

4.8.4.2 - Temperature

coefficient

(20/- 55/20) °C and

(20/125/20) °C ± 100 ppm/K ± 200 ppm/K

4.13 - Short time

overload U = 2.5 x  2 x Umax.; 5 s ± (2 % R + 0.1 )

4.17.5 58 (Td) Solderability

Pre-aging

4 h at 155 °C,

dryheat

Solder bath method;

Sn60Pb40

non activated flux;

(235 ± 5) °C

(2 ± 0.2) s

Good tinning ( 95 % covered)

no visible damage

Solder bath method;

Sn96.5Ag3Cu0.5

non activated flux;

(245 ± 5) °C

(3 ± 0.3) s

Good tinning ( 95 % covered)

no visible damage

4.18.2 58 (Td) Resistance to

soldering heat

Solder bath method

(260 ± 5) °C; (10 ± 1) s ± (1% R + 0.05 )

4.19 14 (Na) Rapid change

of temperature

30 min. at - 55 °C;

30 min. at 125 °C;

5 cycles

± (0.25 % R + 0.05 ) ± (0.5 % R + 0.05 )

4.24 78 (Cab) Damp heat,

steady state

(40 ± 2) °C;

56 days;

(93 ± 3) % RH

± (1 % R + 0.05 )± (2 % R + 0.1 )

4.36 - Operation at low

temperature -55 °C, 1 h ± (1 % R + 0.05 )

4.25.1 - Endurance

at 70 °C

U =  Umax.;

1.5 h on; 0.5 h off;

70 °C; 1000 h ± (1 % R + 0.05 )± (2 % R + 0.1 )

70 °C; 8000 h ± (2 % R + 0.1 )± (4 % R + 0.1 )

4.25.3 -

Endurance at

upper category

temperature

155 °C, 1000 h ± (1 % R + 0.05 )± (2 % R + 0.1 )

- 55 - 25 0 2 55 0 75 100 125 155175

120

100

Ambient Te mperature in °C 70

R ated Power in %

Derating

P70 x R

CRCW...C e3

www.vishay.com Vishay

Revision: 02-Nov-17 4Document Number: 28773

For technical questions, contact: ff3aresistors@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

APPLICABLE SPECIFICATIONS

• EN 60115-1 Generic specification

• EN 140400 Sectional specification

• EN 140401-802 Detail specification

• IEC 60068-2-X Variety of environmental test procedures

• IEC 60286-3 Packaging of SMD components

Legal Disclaimer Notice

www.vishay.com Vishay

Revision: 01-Jan-2019 1Document Number: 91000

Disclaimer

ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE

RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.

Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,

“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other

disclosure relating to any product.

Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or

the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all

liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,

consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular

purpose, non-infringement and merchantability.

Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of

typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding

statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a

particular product with the properties described in the product specification is suitable for use in a particular application.

Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over

time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s

technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,

including but not limited to the warranty expressed therein.

Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining

applications or for any other application in which the failure of the Vishay product could result in personal injury or death.

Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk.

Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for

such applications.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document

or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.