Current Transducer HAX 1200-S Current Transducer HAX 500..2500-S ( ( ) ) ( ( ) For the electronic) measurement of currents: DC, AC, pulsed, mixed, with a galvanic isolation between the primary circuit (high power) and the secondary circuit (electronic circuit). IPN = 1200 A ==500..2500 A VIPN 4V out 46138 Electrical data Electrical data IPN Primary rms rms Primary current 1200 A nominal Type 5) IPM 3600 A current rms measuring range VC ( 5 %) 5) 15 V IPN (A) IPM (A) IC 15 mA IP At 500 1500 HAX30,000 500-S R IS @ @ 500 VDC 1800 1000 MW 600 HAX>600-S VOUT @ IPN, RL = 10 kW k2550 W, TA = 25C 4 V 40 mV 850 @ HAX850-S ROUT 100 W 1000 3000 HAX 1000-S RL 1 kW 1500 4500 HAX>1500-S 2000 5500 HAX 2000-S 2500 Accuracy-Dynamic performance data 5500 HAX 2500-S X @ @ I , T = 25C ( ()) VC Supply voltage2)PN( 5A %) 4) (0 .. I ) PN IC L Current consumption V @ TA = 25C IP OE Overload capability V @ IP = 0, 1 x IPN RIS OH Isolation resistance @ 500 VDC TCVOE VOE VOUT Output voltage @ IPN, RL = 10kW, TA = 25C TCVOUT VOUT (% (% of reading) ROUT Output internal resistance approx. tr @ @ 90% of IPN RL Load resistance di/dt di/dt 3) performance data Accuracy - Dynamic BW (0 .. - 3 dB) <1 % 15 V < 1 % of IPN < +20/-15 mA < 20 mV 30,000 At < 30 mV > 1000 MW <1 mV/K 4 V < 0.1 %/K 100 W <5 s > 1 kW > 50 A/ A/ s DC .. 25 kHz X < 1 % < 1 % of IPN < 20 - 25 .. + 85mVC Accuracy @ I , T = 25C (excluding offset) L VT OE A VT OH PN A General 1) Linearity error (0 .. Idata ) PN Electrical offset voltage @ TA = 25C Hysteresis offset voltage @ IP = 0; S after an excursion of 1 x IPN m TCVOE Temperature coefficient of VOE 4) TCVOUT Temperature coefficient of VOUT (% of reading) tr Response time to 90% of IPN step Isolation characteristics di/dt di/dt accurately followed BW Frequency bandwidth 2) (- 3 dB) V b - 25 .. + 85 C < 30 mV g 450 < 1 mV/K EN 50178: 1997 < 0.1 %/K < 5 s > 50 A/s DC .. 25 kHz V 500 1) * Features * Hall effect measuring principle * Galvanic isolation between * UL94V0 UL94V0 primary and secondary circuit Low power consumption Isolated plastic case recognized according to UL 94-V0 * * Advantages * Easy installation Small size and space savings * Only one design for wide current ratings range High immunity against external interference * * Applications * AC motor speed control * Battery supplied applications Uninterruptible Power Supplies (UPS) Power supplies for welding, cable TV and telecommunication * applications. Application domain Industrial Vd , AC50Hz, 1 min 5 kV General , data dCp 8.5 mm TA Ambient operating temperature - 25 .. + C 85 a TS Ambient storage temperature - 25 .. + 85 C m Mass approx. 450 g Standards 3) EN 50178: 1997 : 1) Pollution class 2, category Notes : 1)2)Linearity data exclude the electrical offset. 2)3) Please refer to derating curves in the technical file to avoid excessive 4) 5)core heating at high frequency 12V 12V 3) Please consult characterisation report for more technical details and application advice. 4) Operating at 12V Vc < 15V will reduce the measuring range. 080402/1 110527/17 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice. Page 1/2 Page 1/3 www.lem.co.jp www.lem.com Current Transducer HAX 500..2500-S Isolation characteristics Vd Ve Vw dCp dCI CTI Rms voltage for AC isolation test, 50 Hz, 1 min 5.0 Partial discharge extinction voltage rms @ 10 pC > 660 Impulse withstand voltage 1.2/50 s 8.3 Creepage distance >8.5 Clearance distance >8.5 Comparative Tracking Index (group IIIa) >275 kV Vrms kV mm mm Applications examples According to EN 50178 and IEC 61010-1 standards and following conditions: Over voltage category OV 3 Pollution degree PD2 Non-uniform field EN 50178 IEC 61010-1 Rated insulation voltage Nominal voltage Basic insulation 800 V 800V Reinforced insulation 400V 300V dCp, dCI,Vw Safety This transducer must be used in electric/electronic equipment with respect to applicable standards and safety requirements in accordance with the manufacturer's operating instructions. Caution, risk of electrical shock When operating the transducer, certain parts of the module can carry hazardous voltage (eg. primary busbar, power supply). Ignoring this warning can lead to injury and/or cause serious damage. This transducer is a built-in device, whose conducting parts must be inaccessible after installation. A protective housing or additional shield could be used. Main supply must be able to be disconnected. Page 2/3 110527/17 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice. www.lem.com Dimensions HAX 500..2500-S (in mm. 1 mm = 0.0394 inch) HAX 500 to 2500-S Dimensions (in mm) 56 18.5 18.5 11 d 5.5 10 11 25 46 18 d 5.5 Max 5 Positive Current Flow 108 62 4 21 12 64 17 4 45 4 1 1 MOLEX Connector 5045-04A 1 126 144 Fixation by base-plate or on bus bar with M5 screws Pins arrangement: 1 2 3 4 (+) (-) Output 0V Mechanical characteristics General tolerance 1.0 mm Page 3/3 110527/17 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice. www.lem.com