Cat.No.P16E-18
Murata
Manufacturing Co., Ltd.
Ceramic Resonators
(CERALOCKr)
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
for EU RoHS Compliant
• All the products in this catalog comply with EU RoHS.
• EU RoHS is "the European Directive 2002/95/EC on the Restriction of the Use
of Certain Hazardous Substances in Electrical and Electronic Equipment".
• For more details, please refer to our website 'Murata's Approach for EU RoHS'
(http://www.murata.com/info/rohs.html).
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
1
2
3
4
5
6
7
1
2
3
4
5
6
7
Selection Guide 2
Part Numbering 3
MHz Chip Type -Tight Frequency Tolerance for Automotive- 4
Application Circuits Utilization 6
MHz Chip Type -Standard Frequency Tolerance for Automotive- 7
Application Circuits Utilization 11
MHz Chip Type Notice (Soldering and Mounting) for Automotive 12
MHz Chip Type Notice for Automotive 13
MHz Chip Type Packaging for Automotive 14
MHz Chip Type -Tight Frequency Tolerance for General Usage- 16
Application Circuits Utilization 20
MHz Chip Type -Standard Frequency Tolerance for General Usage- 21
Application Circuits Utilization 26
MHz Lead Type -Standard Frequency Tolerance for General Usage- 28
kHz Chip Type -Standard Frequency Tolerance for General Usage- 30
kHz Lead Type -Standard Frequency Tolerance for General Usage- 32
MHz Chip Type Notice (Soldering and Mounting) for General Usage 34
MHz Chip Type Notice for General Usage 38
MHz Lead Type Notice for General Usage 39
kHz Type Notice for General Usage 40
MHz Chip Type Packaging for General Usage 43
MHz Lead Type Packaging for General Usage 46
kHz Type Packaging for General Usage 49
CERALOCKr and "CERALOCK" in this catalog are
the trademarks of Murata Manufacturing Co., Ltd.
CONTENTS
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Recycled Paper
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
2
Start
Applications
FunctionsFunctions
Frequencies
SMDSMDSMDSMD LeadedSMDLeadedSMD
Consumer Automotive
Full Speed USB
(high-precision)
Automotive
Network
(high-precision)
Card
(small, low-profile) General Usage
MHz
kHz
Other
Automotive Usage
CSBFB_J
430–519kHz
CSBLA_E
375–429kHz
CSTCC_G
2.00–3.99MHz
CSTLS_G
3.40–10.00MHz
CSTCR_G15L
pp
6.00MHz
CSTCE_G
8.00–13.99MHz
CSTCC_G_A
2.00–3.99MHz
CSTCR_G15C
pp
4.00–7.99MHz
CSBFB_J
700–1250kHz
CSBLA_E
430–509kHz
CSTCR_G
4.00–7.99MHz
CSTLS_X
16.00–70.00MHz
CSTCE_G15L
pp
12.00MHz
CSTCE_V
14.00–20.00MHz
CSTCR_G_B
4.00–7.99MHz
CSTCE_G15C
pp
8.00–13.99MHz
CSBLA_E
510–699kHz
CSTCE_G
8.00–13.99MHz
CSALS_X
16.00–70.00MHz
CSTCE_V13L
pp
16.00MHz
CSTCG_V
20.00–33.86MHz
CSTCE_G_A
8.00–13.99MHz
CSBLA_J
700–1250kHz
CSTCE_V
14.00–20.00MHz
CSTCW_X
20.01–70.00MHz
CSACW_X
20.01–70.00MHz
The kHz resonators have
only two terminals.
(Two Terminals)
(Two Terminals)
CSTCW_X11
ppp
24.00MHz
CSTCZ_X12R
pp
48.00MHz
CSTCE_V13C
pp
14.00–20.00MHz
CSTCW_X_M
25.00–48.00MHz
CSTCV_X_Q
20.01–70.00MHz
CSACV_X_Q
20.01–70.00MHz
(Two Terminals)
CSTCE_V_C
14.00–20.00MHz
p
: Alphanumerics express individual specification
SMD
High Speed USB
(high-precision)
CSTCE_XT
pppp
24.00–27.20
/30.00MHz
Notice) "CERALOCKr for general usage" and "CERALOCKr for automotive" is different in the specification of Operating Temperature Range, Environmental Characteristics,
Physical Characteristics and so on. Please choose either "for general usage" or "for automotive" according to the required specification.
Selection Guide
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
3
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
o Part Numbering
qProduct ID
wFrequency/Capacitance
eStructure/Size
tDesign
oPackaging
CERALOCKr (MHz)
CS Ceramic Resonators
Gpp
T/Vpp
Xpp
A
T
MHz No capacitance built-in
MHz Built-in Capacitance
LS
CC
CR/CE/CG
CV
CW/CZ
Round Lead Type
Cap Chip Type
Small-cap Chip Type
Monolithic Chip Type
Small Monolithic Chip Type
Thickness Shear mode
Thickness Expander mode
Thickness Expander mode (3rd overtone)
Three-digit alphanumerics express
"Individual Specification".
Structure/Size
-B0
-A0
-R0
-R1
Packaging
Product ID
Code
Code
Code
iIndividual Specification
***
Code
Frequency/Capacitance
Design
Individual Specification
Code
(Part Number)
rNominal Center Frequency
Expressed by four-digit alphanumerics. The unit is in hertz (Hz).
Decimal point is expressed by capital letter "M".
With standard products, "iIndividual Specification" is omitted, and
"oPackaging" is carried up.
Bulk
Radial Taping H0=18mm
Plastic Taping ø=180mm
Plastic Taping ø=330mm
yInitial Frequency Tolerance
5
3
2
1
H
K
Design
Code
±0.5%
±0.3%
±0.2%
±0.1%
±0.07%
-0.025/0.02%
uLoad Capacity
1
2
3
4
5
6
Design
Code
3/5/6pF
10pF
15pF
22pF
30/33/39pF
47pF
e
CE
w
T
r
16M0
q
CS
pp indicates initial frequency tolerance and load capacity.
Radial taping is applied to lead type and plastic taping to chip type.
i
***
t
V
y
5
u
3
o
-R0
y
***
e
FB
w
B
r
500K
t
J58
u
-R1
q
CS
qProduct ID
wFrequency/Capacitance
eStructure/Size
rNominal Center Frequency
tDesign
uPackaging
CERALOCKr (kHz)
CS Ceramic Resonators Epp
Jpp
BkHz No capacitance built-in
LA
FB
Two-Terminal Lead Type
SMD Type
Area Expansion mode
Area Expansion mode (Closed Type)
Three-digit alphanumerics express
"Individual Specification".
Structure/Size
-B0
-R1
Packaging
Product ID
Code
Code
Code
yIndividual Specification
***
Code
Frequency/Capacitance
Design
Individual Specification
Code
(Part Number)
Expressed by four-digit alphanumerics. The unit is in hertz (Hz).
Capital letter "K" following three figures expresses the unit of
"kHz". In case of 1.0MHz (1000kHz) or above, expressed by
three figures and capital letter "M" for decimal point.
With standard products, "yIndividual Specification" is omitted, and
"uPackaging" is carried up.
Bulk
Plastic Taping ø=330mm
pp indicates initial frequency tolerance and load capacitance.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
4
1
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Ceramic Resonators (CERALOCKr)
MHz Chip Type -Tight Frequency Tolerance for Automotive-
Chip type "CERALOCK" with built-in load capacitors in
an extremely small package provides high accuracy.
MURATA's frequency adjustment and package technology
expertise has enabled the development of the chip
"CERALOCK" with built-in load capacitors.
Chip "CERALOCK" for automotive has achieved importance
in the worldwide automotive market. This diverse
series owes its development to MURATA's original mass
production techniques and high reliability.
■ Features
1. The series are high accuracy resonators whose total
tolerance is available for less than +-3,000ppm.
2. The series has high reliability and is available
for wide temperature range.
3. Oscillation circuits do not require external load
capacitors.
4. The series is available for a wide temperature range.
5. The resonators are extremely small and have a low
profile.
6. No adjustment is necessary for oscillation circuits.
■ Applications
1. Cluster panel and Control panel
2. Safety control
(Anti-lock Brake System, Electronic Stability
Control, Airbag, etc.)
3. Engine ECU, Electronic Power Steering, Immobilizer,
etc.
4. Car Air-conditioner, Power window, Remote Keyless
Entry system, etc.
5. Intelligent Transportation System
(Lane Keeping System, Millimeter wave radar, etc.)
6. Battery control for hybrid car
4.5±0.1
4.1 max.
0.4 (ref.)
0.4±0.1 0.4±0.1
0.4±0.1
(3) (2) (1)
0.6±0.05
0.75±0.1 1.5±0.1 1.5±0.1
0.4 (ref.)
0.4 (ref.)
0.2±0.2
0.30±0.20
2.0±0.1
1.1±0.1
1.4 max.
∗: EIAJ Monthly
Code
(in mm)
∗
CSTCR_G15C
4.00-7.99MHz
3.2±0.15
1.3±0.15
0.50 (ref.) 0.50 (ref.)
0.50 (ref.)
3.0 max.
0.10±0.10
0.4±0.1
0.4±0.1 1.2±0.1 1.2±0.1
(1)(2)(3)
0.1±0.1
1.1 max.
0.4±0.1
0.70±0.10
0.4±0.1 0.4±0.1
(in mm)
∗
CSTCE_G15C
8.00-13.99MHz
3.2±0.15
0.10±0.10
0.1±0.1
1.3±0.15
1.1 max.
0.4±0.1
0.5 (ref.) 0.5 (ref.)
0.9±0.1
3.0 max.
0.4±0.1 (1)(2)(3)
0.4±0.1 1.2±0.1 1.2±0.1
0.4±0.10.4±0.1
0.5 (ref.)
(in mm)
∗: EIAJ Monthly
Code
∗
CSTCE_V13C
14.00-20.00MHz
Part Number Oscillating
Frequency
(MHz)
Initial
Tolerance Temp. Stability
(%)
Temperature
Range
(°C)
CSTCR_G15C 4.00 to 7.99 ±0.1% ±0.13 -40 to 125
CSTCE_G15C 8.00 to 13.99 ±0.1% ±0.13 -40 to 125
CSTCE_V13C 14.00 to 20.00 ±0.1% ±0.13 -40 to 125
Irregular or stop oscillation may occur under unmatched circuit conditions. Please check the actual conditions prior to use.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
5
1
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
■ Oscillation Frequency Measuring Circuit
VDD
Rf To Frequency Counter
5pF
1MΩ
Rd
C1 C2
(1) (3)
(2)
■ Standard Land Pattern Dimensions
CSTCR_G15C
2.6
0.4
1.5 1.5
1.1
0.4 0.41.1
Land Pattern
(in mm)
CSTCE_G15C
0.4
1.90 ~ 2.10
0.4 0.40.8
Land Pattern
0.8
1.2 1.2
(in mm)
CSTCE_V13C
0.4
1.90 ~ 2.10
0.4 0.40.8
Land Pattern
0.8
1.2 1.2
(in mm)
■ Oscillation Frequency Temperature Stability
CSTCR_G15C
-60 -40 -20 0 +20 +40 +60 +80 +100 +120 +140
Oscillating Frequency Shift (%)
+0.2
+0.1
0
-0.1
-0.2
Temperature (°C)
CSTCE_G15C
-60 -40 -20 0 +20 +40 +60 +80 +100 +120 +140
Oscillating Frequency Shift (%)
Temperature (°C)
+0.2
+0.1
0
-0.1
-0.2
CSTCE_V13C
-60 -40 -20 0 +20 +40 +60 +80 +100 +120 +140
Oscillating Frequency Shift (%)
+0.2
+0.1
0
-0.1
-0.2
Temperature (°C)
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
Application Circuits Utilization
6
1
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
■ TMP92CD54IF (Toshiba)
16-bit Microcomputer
H1
0.1µF
74 72 L
IC : TMP92CD54IF
Vcc3=3.3V
CERALOCKr
C1C2CERALOCKr: CSTCE10M0G15Cpp-R0
C1=33pF (Typ.)
C2=33pF (Typ.)
H2
Vcc5=5.0V
V2V1
H1: 36, 68, 86
H2: 2, 4, 15, 40, 50, 61, 75
L: 1, 3, 13, 38, 51, 63, 73, 88
■ MB90F387 (Fujitsu)
16-bit Microcomputer
H
0.1µF
28 27 L26
IC : MB90F387
Vcc=5.0V
CERALOCKr
C1C2CERALOCKr: CSTCE8M00G15Cpp-R0
C1=33pF (Typ.)
C2=33pF (Typ.)
V2V1
H: 1, 2, 21, 22, 24
L: 20, 23, 25, 48
■ MC68HC908AZ60AVFU (Freescale)
8-bit Microcomputer
59 58 GND
EVALUATION BOARD
IC : MC68HC908AZ60AVFU
Vdd=5.0V
CERALOCKr: CSTCE16M0V13C-R0
C1=15pF (Typ.)
C2=15pF (Typ.)
CERALOCKr
C1C2
V2V1
1MΩ
■ ST72F561 (HS) (ST Microelectronics)
8-bit Microcomputer
H 60
1 2 L
IC : ST72F561 (HS)
Vdd=5.0V
H: 9, 25, 41, 57, 58
L: 8, 24, 40, 55, 56
CERALOCKr
C1C2CERALOCKr: CSTCE8M00G15App-R0
C1=33pF (Typ.)
C2=33pF (Typ.)
V2V1
■ uPD70F3283YGC (NEC Electronics)
32-bit Microcomputer
H 14
12 13 L10
4.7µF
IC : µPD70F3283YGC
Vdd=3.3V
10kΩ
H: 1, 5, 9, 34, 70
L: 2, 8, 11, 15, 33, 69
CERALOCKr
C1C2CERALOCKr: CSTCE10M0G15Cpp-R0
C1=33pF (Typ.)
C2=33pF (Typ.)
V2V1
■ M30842MCT-XXXGP (Renesas)
16-bit Microcomputer
H 19
22 20 L
IC : M30842MCT-XXXGP (High*)
H: 23, 24, 37, 39, 59, 74, 91, 118, 122,
132, 142, 143
L: 15, 16, 21, 36, 41, 57, 76, 93,
110~113, 120, 121, 130, 140
CERALOCKr
C1C2CERALOCKr: CSTCE8M00G15Cpp-R0
C1=33pF (Typ.)
C2=33pF (Typ.)
V2V1
Vcc=5.0V
*High: XIN-XOUT Drive Capacity Select Bit
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
7
2
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Ceramic Resonators (CERALOCKr)
MHz Chip Type -Standard Frequency Tolerance for Automotive-
Chip type "CERALOCK" with built-in load capacitors in
an extremely small package provides high accuracy.
MURATA's frequency adjustment and package technology
expertise has enabled the development of the chip
"CERALOCK" with built-in load capacitors.
Chip "CERALOCK" for automotive has achieved importance
in the worldwide automotive market. This diverse
series owes its development to MURATA's original mass
production techniques and high reliability.
■ Features
1. The series has high reliability and is available
for wide temperature range.
2. Oscillation circuits do not require external load
capacitors.
3. The series is available in a wide frequency range.
4. The resonators are extremely small and have a low
profile.
5. No adjustment is necessary for oscillation circuits.
■ Applications
1. Cluster panel and Control panel
2. Safety control
(Anti-lock Brake System, Electronic Stability
Control, Airbag, etc.)
3. Engine ECU, Electronic Power Steering, Immobilizer,
etc.
4. Car Air-conditioner, Power Window, Remote Keyless
Entry system, etc.
5. Electronic Toll Collection system, Car Navigation,
etc.
0.45
(Ref.)
1.2±0.2
6.6 max.
(3) (2) (1)
0.3±0.3 0.5±0.05
2.5±0.1 2.5±0.1
1.1±0.1
7.2±0.2
3.0±0.2
t
0.45±0.3
∗
∗ : EIAJ code
t : 1.75±0.05
(2.00—2.99MHz)
t : 1.55±0.05
(3.00MHz—)
1.4±0.2 1.2±0.2
0.45
(Ref.) 0.45
(Ref.)
2.1 max.
(in mm)
CSTCC_G_A
2.00-3.99MHz
4.5±0.1
∗
4.1 max.
0.8±0.1
0.75±0.1 1.5±0.1 1.5±0.1
0.4±0.1 0.4±0.1 0.4±0.1
0.8±0.1 0.8±0.1
0.4 (ref.)0.4 (ref.)0.4 (ref.)
0.4±0.05
0.2±0.2
0.3±0.2
2.0±0.1
1.4 max.
(2) (1)(3)
1.15±0.05
∗ : EIAJ Monthly
Code
(in mm)
CSTCR_G_B
4.00-7.99MHz
3.2±0.15
1.3±0.15
0.50 (ref.) 0.50 (ref.)
0.50 (ref.)
3.0 max.
0.10±0.10
0.4±0.1
0.4±0.1 1.2±0.1 1.2±0.1
(1)(2)(3)
0.1±0.1
1.1 max.
0.4±0.1
0.70±0.10
0.4±0.1 0.4±0.1
(in mm)
∗
CSTCE_G_A
8.00-13.99MHz
3.2±0.15
0.10±0.10
0.1±0.1
1.3±0.15
1.1 max.
0.4±0.1
0.5 (ref.) 0.5 (ref.)
0.9±0.1
3.0 max.
0.4±0.1 (1)(2)(3)
0.4±0.1 1.2±0.1 1.2±0.1
0.4±0.10.4±0.1
0.5 (ref.)
(in mm)
∗: EIAJ Monthly
Code
∗
CSTCE_V_C
14.00-20.00MHz
M
∗
∗
3.7±0.2
3.1±0.2
1.3±0.1
(0.5)
(3)
0.4±0.2
0.5 0.50.5 0.4±0.20.5±0.2
(0.5)
(1)
(0.5)
(2)
1.6±0.2
1.85±0.3 1.6±0.2
Terminals (1) and (3) are
interchangeable.
Terminal (2) should be soldered
only to fix the resonator onto P.C.B.
Terminal (2) should be electrically
floating so it cannot be connected
anywhere.
: EIAJ Monthly Code
(in mm)
Thickness varies
with frequency.
CSACV_X_Q
20.01-70.00MHz
Continued on the following page.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
8
2
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Continued from the preceding page.
M
∗
3.7±0.2
3.1±0.2
1.3±0.1
(0.7)
(3)
0.4±0.2
0.5 0.50.5 0.4±0.20.5±0.2
(0.7)
(1)
(0.9)
(2)
1.6±0.2
1.85±0.3 1.6±0.2 (in mm)
Thickness varies
with frequency and
built-in capacitance.
*: EIAJ code
CSTCV_X_Q
20.01-70.00MHz
Part Number Oscillating
Frequency
(MHz)
Initial
Tolerance Temp. Stability
(%)
Temperature
Range
(°C)
CSTCC_G_A 2.00 to 3.99 ±0.5% ±0.4
[-0.6% to +0.3%:Built-in Capacitance 47pF type within Freq.2.00 to 3.49MHz] -40 to 125
CSTCR_G_B 4.00 to 7.99 ±0.5% ±0.15 -40 to 125
CSTCE_G_A 8.00 to 13.99 ±0.5% ±0.2 -40 to 125
CSTCE_V_C 14.00 to 20.00 ±0.5% ±0.15 -40 to 125
CSACV_X_Q 20.01 to 70.00 ±0.5% ±0.3 -40 to 125
CSTCV_X_Q 20.01 to 70.00 ±0.5% ±0.3 -40 to 125
Irregular or stop oscillation may occur under unmatched circuit conditions. Please check the actual conditions prior to use.
■ Oscillation Frequency Measuring Circuit
CSTCC_G_A
Rf
Rd
VDD
C1 C2
To Frequency counter
(1) (3)
(2)
CSTCE_G_A/CSTCE_V_C/CSTCR_G_B/CSTCV_X_Q
VDD
Rf To Frequency Counter
5pF
1MΩ
Rd
C1 C2
(1) (3)
(2)
CSACV_X_Q
VDD
Rf
CL1 CL2
To Frequency Counter
22µF
0.01µF
+
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
9
2
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
■ Standard Land Pattern Dimensions
CSTCC_G_A
3.8~4.4
1.2 1.2
2.5 2.5
1.4 1.2 1.2
Land Pattern (in mm)
CSTCR_G_B
2.6
1.6
0.8
0.4
1.5 1.5
0.4 0.4
0.8 0.8
0.70.7
Land Pattern
(in mm)
CSTCE_G_A
0.4
1.90 ~ 2.10
0.4 0.40.8
Land Pattern
0.8
1.2 1.2
(in mm)
CSTCE_V_C
0.4
1.90 ~ 2.10
0.4 0.40.8
Land Pattern
0.8
1.2 1.2
(in mm)
CSTCV_X_Q
0.5 1.1 0.5 1.1 0.5
1.6 1.6
1.0
3.1±0.2
1.0
0.50.5
Land Pattern
(in mm)
CSACV_X_Q
0.5 1.1 0.5 1.1 0.5
1.6 1.6
1.0
3.1±0.2
1.0
0.5
0.5
Land Pattern
(in mm)
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
10
2
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
■ Oscillation Frequency Temperature Stability
CSTCC_G_A
-60 -40 -20 0 +20 +40 +60 +80 +100 +120 +140
Oscillating Frequency Shift (%)
Temperature (°C)
+0.2
+0.1
0
-0.1
-0.2
CSTCR_G_B
-60 -40 -20 0 +20 +40 +60 +80 +100 +120 +140
Oscillating Frequency Shift (%)
+0.2
+0.1
0
-0.1
-0.2
Temperature (°C)
CSTCE_G_A
-60 -40 -20 0 +20 +40 +60 +80 +100 +120 +140
Oscillating Frequency Shift (%)
Temperature (°C)
+0.2
+0.1
0
-0.1
-0.2
CSTCE_V_C
-60 -40 -20 0 +20 +40 +60 +80 +100 +120 +140
Oscillating Frequency Shift (%)
+0.2
+0.1
0
-0.1
-0.2
Temperature (°C)
CSTCV_X_Q
-60 -40 -20 0 +20 +40 +60 +80 +100 +120 +140
Oscillating Frequency Shift (%)
Temperature (°C)
+0.2
+0.1
0
-0.1
-0.2
CSACV_X_Q
-60 -40 -20 0 +20 +40 +60 +80 +100 +120 +140
Oscillating Frequency Shift (%)
Temperature (°C)
+0.2
+0.1
0
-0.1
-0.2
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
Application Circuits Utilization
11
2
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
■ uPD78F9222MC-5A4 (NEC Electronics)
8-bit Microcomputer
H
2 3
10kΩ
L8
IC : µPD78F9222MC-5A4
Vdd=5.0V
H: 5, 20
L: 1
CERALOCKr
C1C2CERALOCKr: CSTCR6M00G55B-R0
C1=39pF (Typ.)
C2=39pF (Typ.)
6
V'dd=7.0V
V2V1
■ M30260F8AGP (Renesas)
16-bit Microcomputer
H 7
23 24 L
IC : M30260F8AGP (High*)
Vcc=5.0V
H: 11, 46, 47, 48
L: 4, 9, 44
*High: XIN-XOUT Drive Capacity Select Bit
CERALOCKr
C1C2CERALOCKr: CSTCE10M0G55A-R0
C1=33pF (Typ.)
C2=33pF (Typ.)
V2V1
■ MB90F347D (Fujitsu)
16-bit Microcomputer
H
93 92 L
IC : MB90F347D
Vcc=5.0V
CERALOCKr
C1C2CERALOCKr: CSTCE8M00G55A-R0
C1=33pF (Typ.)
C2=33pF (Typ.)
V2V1
H: 15, 32, 65, 90
L: 16, 35, 44, 66, 91
■ MC68HC908AZ60AVFU (Freescale)
8-bit Microcomputer
59 58 GND
EVALUATION BOARD
IC : MC68HC908AZ60AVFU
Vdd=5.0V
CERALOCKr: CSTCE16M0V53C-R0
C1=15pF (Typ.)
C2=15pF (Typ.)
CERALOCKr
C1C2
V2V1
1MΩ
■ ST72F324J6T3 (MS) (ST Microelectronics)
8-bit Microcomputer
H
42 41 L
IC : ST72F324J6T3 (MS)
Vdd=5.0V
CERALOCKr
C1C2CERALOCKr: CSTCR4M00G55B-R0
C1=39pF (Typ.)
C2=39pF (Typ.)
V2V1
H: 13, 21, 32, 43
L: 14, 22, 33, 39, 40
■ PIC12F675-I/P (HS) (Microchip)
8-bit Microcomputer
2 3 L
IC : PIC12F675-I/P(HS)
Vdd=5.0V
CERALOCKr: CSTCE8M00G52A-R0
C1=10pF (Typ.)
C2=10pF (Typ.)
CERALOCKr
C1C2
V2V1
1MΩ
H
H: 1
L: 4, 8
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
One heat stress, shown in the profile at right, is applied to
resonator; then, after being placed in natural conditions
for 1 hour, the resonator is measured.
(a) Pre-heating conditions should be +150 to +180°C for
60 to 120 seconds. Ascending time up to +150°C
should be longer than 30 seconds.
(b) Heating conditions should be within 40 seconds at
+230°C min., but peak temperature should be Iower
than +260°C.
1. Soldering Conditions
(1) Reflow
HCFC, Isopropanol, Tap water, Demineralized water,
Cleanthrough750H, Pine alpha 100S, Techno care FRW
2. Wash
3. Notice for Mounting
(1) Cleaning Solvents
dT<=60°C (dT=Component-solvent)
*1 ex. In case the component at +90°C immerses into
cleaning solvent at +60°C, then dT=30°C.
(2) Temperature Difference : dT *1
5 minutes max. by air blow at +80°C max.
(4) Drying
(a) Total washing time should be within 10 minutes.
(b) The component may be damaged if it is washed with
chlorine, petroleum, or alkali cleaning solvent.
(a) The component is recommended for use with
placement machines which employ optical placement
capabilities. The component might be damaged by
excessive mechanical force. Please make sure to
evaluate by using placement machines before going
into mass production. Do not use placement
machines which utilize mechanical positioning. Please
contact Murata for details beforehand.
(b) Please insure the component is thoroughly evaluated
in your application circuit.
(c) Please do not apply excess mechanical stress to the
component and terminals during soldering.
(5) Others
(a) Ultrasonic Wash
1 minute max. in above solvent at +60°C max.
(Frequency: 28kHz, Output: 20W/l)
(b) Immersion Wash
5 minutes max. in above solvent at +60°C max.
(c) Shower or Rinse Wash
5 minutes max. in above solvent at +60°C max.
(3) Conditions
Components shall be measured after soldering on PCB
at +350±5°C for 3.0±0.5 seconds and leaving in natural
condition for 24 hours. The soldering iron shall not touch
the components while soldering.
(2) Soldering Iron
150
230
180
30 sec.
min. 40 sec.
max.
Peak
(260˚C max.)
Pre-heating
(150-180˚C)
Heating
(230˚C)
Gradual
Cooling
120 sec.
min.
60-120 sec.
Temperature (˚C)
■ CSTCC/CSTCR/CSTCE_V/CSTCE_G/CSTCV/CSACV Series
MHz Chip Type Notice (Soldering and Mounting) for Automotive
12
2
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
MHz Chip Type Notice for Automotive
13
2
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
■ Notice (Storage and Operating Conditions)
■ Notice (Rating)
The component may be damaged if excess mechanical
stress is applied.
■ Notice (Handling)
"CERALOCK" may stop oscillating or oscillate
irregularly under improper circuit conditions.
1. Product Storage Condition
Please store the products in room where the
temperature/humidity is stable. And avoid
such places where there are large temperature
changes. Please store the products under the
following conditions:
Temperature: -10 to + 40 degrees C
Humidity: 15 to 85% R.H.
2. Expire Date on Storage
Expire date (Shelf life) of the products is six
months after delivery under the conditions of a
sealed and an unopened package. Please use the
products within six months after delivery. If you
store the products for a long time (more than six
months), use carefully because the products may
be degraded in the solderability and/or rusty.
Please confirm solderability and characteristics
for the products regularly.
3. Notice on Product Storage
(1) Please do not store the products in a chemical
atmosphere (Acids, Alkali, Bases, Organic gas,
Sulfides and so on), because the characteristics
may be reduced in quality, and/or be degraded in
the solderability due to the storage in a
chemical atmosphere.
(2) Please do not put the products directly on the
floor without anything under them to avoid damp
places and/or dusty places.
(3) Please do not store the products in the places
such as: in a damp heated place, in a place where
direct sunlight comes in, in place applying
vibrations.
(4) Please use the products immediately after the
package is opened, because the characteristics
may be reduced in quality, and/or be degraded in
the solderability due to storage under the poor
condition.
(5) Please do not drop the products to avoid cracking
of ceramic element.
4. Others
Conformal coating of the component is acceptable.
However, the resin material, curing temperature, and
other process conditions should be evaluated to
confirm that stable electrical characteristics are
maintained.
Please be sure to consult with our sales representative
or engineer whenever and prior to using the products.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
MHz Chip Type Packaging for Automotive
14
2
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
■ Minimum Quantity
(in mm)
(pcs.)
a b
CSTCC_G_A
CSTCR_G_B
CSTCR_G15C
CSTCE_G_A
CSTCE_G15C
CSTCE_V_C
CSTCE_V13C
CSTCV_X_Q
CSACV_X_Q
Part Number Plastic Tape ø180mm Plastic Tape ø330mm Bulk Dimensions
2,000
3,000
3,000
3,000
3,000
3,000
3,000
2,000
2,000
6,000
9,000
9,000
9,000
9,000
9,000
9,000
6,000
6,000
500
500
500
500
500
500
500
500
500
a
a
a
b
b
b
b
a
a
Trailer Leader
Empty Components
Cover Film
2.0±0.5
160-190
13.0
+1.0
0
0
–1.5
17.0±1.0
(ø180 )
0
–1.5
(ø180 )
ø13.0±0.2
400-560
Empty
160 min.
Trailer
160-190
Empty
160 min.
400-560
Cover Film
Leader
Empty Components
ø13.0±0.2 2.0±0.5
13.0±1.0
c Dimensions of Reel
The order quantity should be an integral multiple of the "Minimum Quantity" shown above.
+1.0
0
9.0
■ Dimensions of Taping
CSTCR_G15C
(in mm)
4.0±0.1 2.0±0.05
(9.5)
4.0±0.1
(3) (2) (1)
ø1.5W0.1
Y0
ø1.5W0.1
Y0
12.0±0.2
5.5±0.05 1.75±0.1
4.7±0.1
0.3±0.05
1.25±0.05
(1.85 max.)
2.2±0.1
Direction of Feed
3˚ max.
10˚ Cover Film
The cover film peel strength force 0.1 to 0.7N
The cover film peel speed 300mm/min.
CSTCE_G15C
(in mm)
2.0±0.05
4.0±0.1
3° max.
3.5±0.05
8.0±0.2
1.75±0.1
0.25±0.05
0.90±0.10
(1.30 max.)
10°
(5.2)
Cover Film
Direction of Feed
The cover film peel strength force 0.1 to 0.7N
The cover film peel speed 300mm/min.
4.0±0.1
1.50±0.1
ø1.5 -0.0
+0.1
ø1.0 -0.0
+0.2
3.40±0.1
(3) (2) (1)
Continued on the following page.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
MHz Chip Type Packaging for Automotive
15
2
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Continued from the preceding page.
■ Dimensions of Taping
CSTCE_V13C
Dimensions of Carrier Tape
(in mm)
4.0±0.1
Cover Film
4.0±0.1
2.0±0.05
8.0±0.2
ø1.5
+0.1
-0.0
ø1.0
+0.1
-0.0
3.5±0.05 1.75±0.1
3.45±0.1
Direction of Feed
0.25±0.05
(1.40 max.)
1.10±0.05
3˚ max.
1.50±0.1
The cover film peel strength force 0.1 to 0.7N
The cover film peel speed 300mm/min.
10˚
(5.2)
(2)(3) (1)
CSTCC_G_A
(in mm)
4.0±0.1 2.0±0.05
+0.3
-0.0
ø1.55±0.05
ø1.5
1.75±0.1
5.5±0.05
12.0±0.2
7.6±0.1
4.0±0.1
(9.5)
3.3±0.1
The cover film peel strength force 0.1 to 0.7N
The cover film peel speed 300mm/min. Cover film
10˚
3˚max.
1.85±0.05
0.3±0.05
(2.45 max.)
Direction of Feed
(3) (2) (1)
CSTCR_G_B
(in mm)
4.0±0.1 2.0±0.05
(9.5)
4.0±0.1
(3) (2) (1)
ø1.5W0.1
Y0
ø1.5W0.1
Y0
12.0±0.2
5.5±0.05 1.75±0.1
4.7±0.1
0.3±0.05
1.25±0.05
(1.85 max.)
2.2±0.1
Direction of Feed
3˚ max.
10˚ Cover Film
The cover film peel strength force 0.1 to 0.7N
The cover film peel speed 300mm/min.
CSTCE_G_A
(in mm)
2.0±0.05
4.0±0.1
3° max.
3.5±0.05
8.0±0.2
1.75±0.1
0.25±0.05
0.90±0.10
(1.30 max.)
10°
(5.2)
Cover Film
Direction of Feed
The cover film peel strength force 0.1 to 0.7N
The cover film peel speed 300mm/min.
4.0±0.1
1.50±0.1
ø1.5 -0.0
+0.1
ø1.0 -0.0
+0.2
3.40±0.1
(3) (2) (1)
CSTCE_V_C
Dimensions of Carrier Tape
(in mm)
4.0±0.1
Cover Film
4.0±0.1
2.0±0.05
8.0±0.2
ø1.5
+0.1
-0.0
ø1.0
+0.1
-0.0
3.5±0.05 1.75±0.1
3.45±0.1
Direction of Feed
0.25±0.05
(1.40 max.)
1.10±0.05
3˚ max.
1.50±0.1
The cover film peel strength force 0.1 to 0.7N
The cover film peel speed 300mm/min.
10˚
(5.2)
(2)(3) (1)
CSTCV_X_Q
(in mm)
Thickness of CERALOCKr
∗1, ∗2 : Dimensions vary with product thickness of CERALOCKr
Cover Film
The cover film peel strength force 0.1 to 0.7N
The cover film peel speed 300mm/min.
Direction of Feed
1.50–1.40 1.30–1.20 1.10–1.00
t1 ∗1
t2 ∗21.65±0.1
2.0 max. 1.45±0.1
1.8 max. 1.2±0.1
1.5 max.
4.0±0.1
4.0±0.1
10°
2.0±0.1
12.0±0.2
5.5±0.1
4.1±0.1 1.75±0.1
W0.1
Y0.0
ø1.5
W0.3
Y0.0
ø1.5
t1 ∗1
t2 ∗2
0.3±0.1
(9.5)
W0.1
Y0.05
3.35
3° max.
(3)(2)(1)
CSACV_X_Q
(in mm)
Thickness of CERALOCKr
∗1, ∗2 : Dimensions vary with product thickness of CERALOCKr
Cover Film
The cover film peel strength force 0.1 to 0.7N
The cover film peel speed 300mm/min.
Direction of Feed
1.50–1.40 1.30–1.20 1.10–1.00
t1 ∗1
t2 ∗21.65±0.1
2.0 max. 1.45±0.1
1.8 max. 1.2±0.1
1.5 max.
4.0±0.1
4.0±0.1
10°
2.0±0.1
12.0±0.2
5.5±0.1
4.1±0.1 1.75±0.1
W0.1
Y0.0
ø1.5
W0.3
Y0.0
ø1.5
t1 ∗1
t2 ∗2
0.3±0.1
(9.5)
W0.1
Y0.05
3.35
3° max.
(3)(2)(1)
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
16
3
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Ceramic Resonators (CERALOCKr)
MHz Chip Type -Tight Frequency Tolerance for General Usage-
Chip type "CERALOCK" with built-in load capacitors in
an extremely small package provides high accuracy.
MURATA's frequency adjustment and package technology
expertise has enabled the development of the chip
"CERALOCK" with built-in load capacitors.
High-density mounting can be realized because of the
small package and the elimination of the need for an
external load capacitor.
■ Features
1. High accuracy resonator realizes initial tolerance
of +-250ppm.
2. Oscillation circuits do not require external load
capacitors.
3. The series is available in a wide frequency range.
4. The resonators are extremely small and have a low
profile.
5. No adjustment is necessary for oscillation circuits.
■ Applications
1. Clock oscillators for USB (High-speed and Full-speed)
controller ICs
2. Storage devices with SATA interface
(HDD, Optical storage device, etc.)
3. Audio equipment and musical instrument, etc.
4. Other applications for replacement from Crystal
Oscillators
4.5±0.1
∗
4.1 max.
0.8±0.1
0.75±0.1 1.5±0.1 1.5±0.1
0.4±0.1 0.4±0.1 0.4±0.1
0.8±0.1 0.8±0.1
0.4 (ref.)0.4 (ref.)0.4 (ref.)
0.4±0.05
0.2±0.2
0.3±0.2
2.0±0.1
1.4 max.
(2) (1)(3)
1.15±0.05
∗ : EIAJ Monthly
Code
(in mm)
CSTCR_G15L
4.00-7.99MHz
3.2±0.15
1.3±0.15
0.50 (ref.) 0.50 (ref.)
0.50 (ref.)
3.0 max.
0.10±0.10
0.4±0.1
0.4±0.1 1.2±0.1 1.2±0.1
(1)(2)(3)
0.1±0.1
1.1 max.
0.4±0.1
0.70±0.10
0.4±0.1 0.4±0.1
(in mm)
∗
CSTCE_G15L
8.00-13.99MHz
3.2±0.15
0.10±0.10
0.1±0.1
1.3±0.15
1.1 max.
0.4±0.1
0.5 (ref.) 0.5 (ref.)
0.9±0.1
3.0 max.
0.4±0.1 (1)(2)(3)
0.4±0.1 1.2±0.1 1.2±0.1
0.4±0.10.4±0.1
0.5 (ref.)
(in mm)
∗: EIAJ Monthly
Code
∗
CSTCE_V13L
14.00-20.00MHz
3.2±0.15
1.3±0.15
0.50 (ref.) 0.50 (ref.)
0.50 (ref.)
3.0 max.
0.10±0.10
0.4±0.1
0.4±0.1 1.2±0.1 1.2±0.1
(1)(2)(3)
0.1±0.1
1.1 max.
0.4±0.1
1.00±0.10
0.4±0.1 0.4±0.1
(in mm)
∗
CSTCE_XK, CSTCE_XT
24.00-27.20/30.00MHz
2.5T0.2 1.4 max.
Thickness varies
with frequency and
built-in capacitance.
*: EIAJ code
0.5T0.2 0.5T0.2
0.5T0.2
1.0T0.21.0T0.2
1.25T0.2
(0.5)
(3) (0.5)
(1)
(0.5)
(2)
0.05+0.10
-
0.05 0.05+0.10
-
0.05
0.4 +0.3
-
0.2
0.4 +0.3
-
0.2
0.4 +0.3
-
0.2
*
2.0T0.2
(in mm)
CSTCW_X11
20.01-29.99MHz
Continued on the following page.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
17
3
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Continued from the preceding page.
2.00T0.05 0.75T0.10
(0.45)(0.45)
(0.60)
(3) (1)(2)
1.60T0.05
(in mm)
0.3+0.20
-0.15
0.3+0.20
-0.15
0.3+0.20
-0.15
*
0.78T0.20
1.00T0.20
0.43T0.10 0.55T0.10 0.43T0.10
0.78T0.20
Thickness varies
with frequency and
built-in capacitance.
*: EIAJ code
CSTCZ_X12R
30.00-48.00MHz
Part Number Oscillating
Frequency
(MHz)
Initial
Tolerance Temp. Stability
(%)
Temperature
Range
(°C)
CSTCR_G15L 4.00 to 7.99 ±0.1% ±0.08 0 to 70
CSTCE_G15L 8.00 to 13.99 ±0.1% ±0.08 0 to 70
CSTCE_V13L 14.00 to 20.00 ±0.1% ±0.08 0 to 70
CSTCW_X11 20.01 to 29.99 ±0.1% ±0.1 0 to 70
CSTCE_XK 24.00 to 27.20
/30.00 +0.02
/-0.025% ±0.015 0 to 70
CSTCE_XT 24.00 to 27.20
/30.00 ±0.027% ±0.015 0 to 70
CSTCZ_X12R 30.00 to 48.00 ±0.15% ±0.05
[0 to 70°C:±0.03%] -30 to 85
CSTCE_XK: Available Frequency is 24.00 to 27.20MHz and 30.00MHz.
CSTCE_XT: Initial tol. Includes freq. aging. Please contact us in case temp. range exceeds 0 to 70 degrees C.
Irregular or stop oscillation may occur under unmatched circuit conditions. Please check the actual conditions prior to use.
■ Oscillation Frequency Measuring Circuit
CSTCR_G15/CSTCE_G15L/CSTCE_V13L
VDD
Rf To Frequency Counter
5pF
1MΩ
Rd
C1 C2
(1) (3)
(2)
CSTCE_XK, CSTCE_XT
Rf
VDD
C1 C2
To Frequency Counter
(1) (3)
(2)
Continued on the following page.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
18
3
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Continued from the preceding page.
■ Oscillation Frequency Measuring Circuit
CSTCW_X11
Rf
Rd
VDD
C1 C2
To Frequency counter
(1) (3)
(2)
CSTCZ_X12R
Rf
VDD
C1 C2
To Frequency Counter
(1) (3)
(2)
■ Standard Land Pattern Dimensions
CSTCR_G15L
2.6
0.4
1.5 1.5
1.1
0.4 0.41.1
Land Pattern
(in mm)
CSTCE_G15L
0.4
1.90 ~ 2.10
0.4 0.40.8
Land Pattern
0.8
1.2 1.2
(in mm)
CSTCE_V13L
0.4
1.90 ~ 2.10
0.4 0.40.8
Land Pattern
0.8
1.2 1.2
(in mm)
CSTCE_XK, CSTCE_XT
0.4
1.90 ~ 2.10
0.4 0.40.8
Land Pattern
0.8
1.2 1.2
(in mm)
CSTCW_X11
0.5 0.50.50.5
1.0 1.0
0.80.8
2.0T0.2
0.30.3
0.5
Land Pattern
(in mm)
CSTCZ_X12R
0.3
2.0
1.6
0.3 0.30.650.65
0.95 0.95
(in mm)
Land Pattern
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
19
3
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
■ Oscillation Frequency Temperature Stability
CSTCR_G15L
-60 -40 -20 0 +20 +40 +60 +80 +100 +120 +140
Oscillating Frequency Shift (%)
+0.2
+0.1
0
-0.1
-0.2
Temperature (°C)
CSTCE_G15L
-60 -40 -20 0 +20 +40 +60 +80 +100 +120 +140
Oscillating Frequency Shift (%)
Temperature (°C)
+0.2
+0.1
0
-0.1
-0.2
CSTCE_V13L
-60 -40 -20 0 +20 +40 +60 +80 +100 +120 +140
Oscillating Frequency Shift (%)
+0.2
+0.1
0
-0.1
-0.2
Temperature (°C)
CSTCE_XK, CSTCE_XT
-60 -40 -20 0 +20 +40 +60 +80 +100 +120 +140
Oscillating Frequency Shift (%)
Temperature (°C)
+1000
+500
0
-500
-1000
CSTCW_X11
Oscillating Frequency Shift (%)
Temperature (°C)
-40 -20 0 +20 +40 +60 +80 +100
+0.2
+0.1
0
-0.1
-0.2
CSTCZ_X12R
Oscillating Frequency Shift (%)
Temperature (°C)
-40 -20 0 +20 +40 +60 +80 +100
+0.2
+0.1
0
-0.1
-0.2
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
Application Circuits Utilization
20
3
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
■ M66291GP (Renesas)
USB Transceiver
14 13 GND
EVALUATION BOARD
IC : M66291GP
Vset=3.3V
CERALOCKr: CSTCR6M00G15ppp-R0
C1=39pF (Typ.)
C2=39pF (Typ.)
V1
220Ω
1MΩ
CERALOCKr
C1C2
V2
■ MN102HF74GHL (Panasonic)
16-bit Microcontroller
H 82 18
Fout
23 24 L
IC : MN102HF74GHL
Vdd=3.3V
H: 1~17, 22, 25, 26~42, 54, 58~60, 66~81, 83~91
L: 19, 20, 43~53, 55~57, 61~65, 82, 92~100
CERALOCKr
C1C2CERALOCKr: CSTCE12M0G15Lpp-R0
C1=33pF (Typ.)
C2=33pF (Typ.)
V2V1
■ LC87F1964A (Sanyo)
8-bit Microcontroller
6 7 LL1
IC : LC87F1964A
Vdd=5.0V
CERALOCKr: CSTCE12M0G15Lpp-R0
C1=33pF (Typ.)
C2=33pF (Typ.)
H H1
V2V1
470Ω
CERALOCKr
C1C2
H: 8, 19, 39
L: 5, 20, 40
H1: 31, 33
L1: 29, 30, 32, 34~36
10kΩ
10kΩ
■ TUSB2046B (Texas Insturuments)
USB 4-port HUB
H
30 29 GND
IC : TUSB2046B
Vcc=3.3V
CERALOCKr
C1C2CERALOCKr: CSTCR6M00G15ppp-R0
C1=39pF (Typ.)
C2=39pF (Typ.)
V2V1
1MΩ
H: 3, 25
L: 7, 28
■ ISP1181BDGG (Philips)
USB Controller
H
48 47 GND
EVALUATION BOARD
IC : ISP1181BDGG
Vset=3.3V
CERALOCKr
C1C2CERALOCKr: CSTCR6M00G15ppp-R0
C1=39pF (Typ.)
C2=39pF (Typ.)
V2V1
■ uPD720114 (NEC Electronics)
USB2.0 (Hi-speed) HUB Controller
VDD
10 11 GND
IC : µPD720114
Vdd=3.3V
CERALOCKr
C1C2CERALOCKr: CSTCE30M0XK1ppp-R0
C1=5pF (Typ.)
C2=5pF (Typ.)
V2V1
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
21
4
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Ceramic Resonators (CERALOCKr)
MHz Chip Type -Standard Frequency Tolerance for General Usage-
Chip type "CERALOCK" with built-in load capacitors
provides extremely small package.
MURATA's package technology expertise has enabled the
development of the Chip "CERALOCK" with built-in load
capacitors.
High-density mounting can be realized because of the
small package and the elimination of the need for an
external load capacitor.
■ Features
1. Oscillation circuits do not require external load
capacitors.
2. The series is available in a wide frequency range.
3. The resonators are extremely small and have a low
profile.
4. No adjustment is necessary for oscillation circuits.
■ Applications
1. Clock oscillators for microprocessors
2. Small electronic equipment such as hand held phone,
digital video camcorder (DVC), digital still camera
(DSC), portable audio player, etc.
3. Storage media and memory
(HDD, Optical storage device, FDD, Flash memory
card, etc.)
4. Office automation equipment
(Mobile PC, Mouse, Keyboard, etc.)
5. Audio-visual applications
(TV, DVD-HDD recorder, Audio equipment, Remote
controller, etc.)
6. Home appliances
(Air conditioner, Microwave oven, Refrigerator,
Washing machine, etc.)
0.45
(Ref.)
1.2±0.2
6.6 max.
(3) (2) (1)
0.3±0.3 0.5±0.05
2.5±0.1 2.5±0.1
1.1±0.1
7.2±0.2
3.0±0.2
t
0.45±0.3
∗
∗ : EIAJ code
t : 1.75±0.05
(2.00—2.99MHz)
t : 1.55±0.05
(3.00MHz—)
1.4±0.2 1.2±0.2
0.45
(Ref.) 0.45
(Ref.)
2.1 max.
(in mm)
CSTCC_G
2.00-3.99MHz
4.5±0.1
∗
4.1 max.
0.8±0.1
0.75±0.1 1.5±0.1 1.5±0.1
0.4±0.1 0.4±0.1 0.4±0.1
0.8±0.1 0.8±0.1
0.4 (ref.)0.4 (ref.)0.4 (ref.)
0.4±0.05
0.2±0.2
0.3±0.2
2.0±0.1
1.4 max.
(2) (1)(3)
1.15±0.05
∗ : EIAJ Monthly
Code
(in mm)
CSTCR_G
4.00-7.99MHz
3.2±0.15
1.3±0.15
0.50 (ref.) 0.50 (ref.)
0.50 (ref.)
3.0 max.
0.10±0.10
0.4±0.1
0.4±0.1 1.2±0.1 1.2±0.1
(1)(2)(3)
0.1±0.1
1.1 max.
0.4±0.1
0.70±0.10
0.4±0.1 0.4±0.1
(in mm)
∗
CSTCE_G
8.00-13.99MHz
3.2±0.15
0.10±0.10
0.1±0.1
1.3±0.15
1.1 max.
0.4±0.1
0.62 (ref.) 0.62 (ref.)
0.9±0.1
3.0 max.
0.6±0.10.4±0.1 0.6±0.1
(1)(2)(3)
0.65±0.1 0.95±0.1 0.95±0.1
0.45 (ref.)
(in mm)
CSTCE_V
14.00-20.00MHz
0.52 (ref.) 0.41 (ref.) 0.52 (ref.)
2.0±0.15
1.3±0.15
0.85±0.1
1.1 max.
0.10±0.10
0.075±0.075 0.4±0.1
1.85 max.
0.5±0.1
0.3±0.1 0.7±0.1 0.7±0.1
0.3±0.1 0.5±0.1
(1)(2)(3)
(in mm)
CSTCG_V
20.00-33.86MHz
(Ultra Small)
Continued on the following page.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
22
4
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Continued from the preceding page.
2.5T0.2 1.2 max.
Thickness varies
with frequency.
*: EIAJ code
0.5T0.2 0.5T0.2
1.0T0.21.0T0.2
1.25T0.2
(0.5) (0.5) 0.05+0.10
-
0.05
0.05+0.10
-
0.05
0.4 +0.3
-
0.2
0.4 +0.3
-
0.2
*
2.0T0.2
(in mm)
CSACW_X
20.01-70.00MHz
2.5T0.2 1.4 max.
Thickness varies
with frequency and
built-in capacitance.
*: EIAJ code
0.5T0.2 0.5T0.2
0.5T0.2
1.0T0.21.0T0.2
1.25T0.2
(0.5)
(3) (0.5)
(1)
(0.5)
(2)
0.05+0.10
-
0.05 0.05+0.10
-
0.05
0.4 +0.3
-
0.2
0.4 +0.3
-
0.2
0.4 +0.3
-
0.2
*
2.0T0.2
(in mm)
CSTCW_X
20.01-70.00MHz
2.5T0.2 0.65 max.
0.5T0.2 0.5T0.20.5T0.2
1.0T0.21.0T0.2
1.25T0.2
(0.5) (0.5)(0.5)
(3) (1)(2)
0.05+0.10
-0.05 0.05+0.10
-0.05
*
2.0T0.2
(in mm)
0.4+0.3
-0.2
0.4+0.3
-0.2
0.4+0.3
-0.2
Thickness varies
with frequency and
built-in capacitance.
ex.) 48.00MHz: 0.44±0.03mm
*: EIAJ code
CSTCW_X_M
25.00-48.00MHz
(Urtra Thin)
Part Number Oscillating
Frequency
(MHz)
Initial
Tolerance Temp. Stability
(%)
Temperature
Range
(°C)
CSTCC_G 2.00 to 3.99 ±0.5% ±0.3
[±0.4%:Built-in Capacitance 47pF type within Freq.2.00 to 3.49MHz] -20 to 80
CSTCR_G 4.00 to 7.99 ±0.5% ±0.2 -20 to 80
CSTCE_G 8.00 to 13.99 ±0.5% ±0.2 -20 to 80
CSTCE_G_Z 8.00 to 13.99 ±0.5% ±0.2 -40 to 125
CSTCE_V 14.00 to 20.00 ±0.5% ±0.3 -20 to 80
CSTCG_V 20.00 to 33.86 ±0.5% ±0.3 -20 to 80
CSACW_X 20.01 to 70.00 ±0.5% ±0.2 -20 to 80
CSTCW_X 20.01 to 70.00 ±0.5% ±0.2 -20 to 80
CSTCW_X_M 25.00 to 48.00 ±0.5% ±0.2 -20 to 80
Irregular or stop oscillation may occur under unmatched circuit conditions. Please check the actual conditions prior to use.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
23
4
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
■ Oscillation Frequency Measuring Circuit
CSTCR_G/CSTCE_G/CSTCE_V/CSTCG_V
VDD
Rf To Frequency Counter
5pF
1MΩ
Rd
C1 C2
(1) (3)
(2)
CSTCC_G/CSTCW_X
Rf
Rd
VDD
C1 C2
To Frequency counter
(1) (3)
(2)
CSACW_X
Rf
Rd
VDD
CL2CL1
To Frequency counter
CSTCW_X_M
Rf
VDD
C1 C2
To Frequency Counter
(1) (3)
(2)
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
24
4
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
■ Standard Land Pattern Dimensions
CSTCC_G
3.8~4.4
1.2 1.2
2.5 2.5
1.4 1.2 1.2
Land Pattern (in mm)
CSTCR_G
2.6
1.6
0.8
0.4
1.5 1.5
0.4 0.4
0.8 0.8
0.70.7
Land Pattern
(in mm)
CSTCE_G
0.4
1.90 ~ 2.10
0.4 0.40.8
Land Pattern
0.8
1.2 1.2
(in mm)
CSTCE_V
Land Pattem
0.3 0.30.65 0.30.65
0.95 0.95
1.6
(in mm)
CSTCG_V
Land Pattem
0.3 0.30.5 0.30.5
0.8 0.8
1.6
(in mm)
CSACW_X
0.5 0.5
2.0
0.80.8
2.0T0.2
0.30.3
Land Pattern
(in mm)
CSTCW_X
0.5 0.50.50.5
1.0 1.0
0.80.8
2.0T0.2
0.30.3
0.5
Land Pattern
(in mm)
CSTCW_X_M
0.5 0.50.50.5
1.0 1.0
0.80.8
2.0
0.30.3
0.5
Land Pattern
(in mm)
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
25
4
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
■ Oscillation Frequency Temperature Stability
CSTCC_G
Oscillating Frequency Shift (%)
Temperature (°C)
-40 -20 0 +20 +40 +60 +80 +100
+0.2
+0.1
0
-0.1
-0.2
CSTCR_G
-60 -40 -20 0 +20 +40 +60 +80 +100 +120 +140
Oscillating Frequency Shift (%)
+0.2
+0.1
0
-0.1
-0.2
Temperature (°C)
CSTCE_G
-60 -40 -20 0 +20 +40 +60 +80 +100 +120 +140
Oscillating Frequency Shift (%)
Temperature (°C)
+0.2
+0.1
0
-0.1
-0.2
CSTCE_V
-60 -40 -20 0 +20 +40 +60 +80 +100 +120 +140
Oscillating Frequency Shift (%)
+0.2
+0.1
0
-0.1
-0.2
Temperature (°C)
CSTCG_V
-60 -40 -20 0 +20 +40 +60 +80 +100 +120 +140
Oscillating Frequency Shift (%)
Temperature (°C)
+0.2
+0.1
0
-0.1
-0.2
CSACW_X
Oscillating Frequency Shift (%)
Temperature (°C)
-40 -20 0 +20 +40 +60 +80 +100
+0.2
+0.1
0
-0.1
-0.2
CSTCW_X
Oscillating Frequency Shift (%)
Temperature (°C)
-40 -20 0 +20 +40 +60 +80 +100
+0.2
+0.1
0
-0.1
-0.2
CSTCW_X_M
Oscillating Frequency Shift (%)
Temperature (°C)
-40 -20 0 +20 +40 +60 +80 +100
+0.2
+0.1
0
-0.1
-0.2
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
Application Circuits Utilization
26
4
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
■ uPD78F0533GB (NEC Electronics)
8-bit Microcomputer
H 6
11 10 L12
0.1µF
IC : µPD78F0533GB
Vdd=5.0V
10kΩ
H: 15, 16, 47
L: 9, 13, 14, 48
CERALOCKr
C1C2CERALOCKr: CSTCR4M00G55-R0
C1=39pF (Typ.)
C2=39pF (Typ.)
V2V1
■ M38235G6HP (Renesas)
8-bit Microcomputer
H 25
28 29 L
M38235G6HP
Vcc=5.0V
H: 71
L: 30, 73
CERALOCKr
C1C2CERALOCKr: CSTLS8M00G53-B0
C1=15pF (Typ.)
C2=15pF (Typ.)
V2V1
■ TMP19A43FDXBG (Toshiba)
32-bit Microcomputer
A14 A15 GND
EVALUATION BOARD
IC : TMP19A43FDXBG
Vcc=1.5V
Xin: A14
Xout: A15
CERALOCKr
C1C2CERALOCKr: CSTCE10M0G52-R0
C1=10pF (Typ.)
C2=10pF (Typ.)
Vcc'=2.5V Vcc''=3.3V
V2V1
■ MN103SFC2D (Panasonic)
32-bit Microcomputer
H
14 13 LVdd2
10µF
IC : MN103SFC2D
Vdd=5.0V
H: 9, 17, 34
L: 7, 15, 36
Vdd2: 16, 38
CERALOCKr
C1C2CERALOCKr: CSTCR5M00G55Z-R0
C1=39pF (Typ.)
C2=39pF (Typ.)
V2V1
■ MB95F128H (Fujitsu)
8-bit Microcomputer
H
56 55 L
IC : MB95F128H
Vcc=5.0V
H: 3, 28, 51, 79
L: 4, 29, 54, 57
CERALOCKr
C1C2CERALOCKr: CSTCE8M00G52-R0
C1=10pF (Typ.)
C2=10pF (Typ.)
V2V1
■ PIC16F716-I/SO (Microchip)
8-bit Microcomputer
H
16 15 GND
EVALUATION BOARD
IC : PIC16F716-I/SO(HS)
Vdd=5.0V
CERALOCKr
C1C2CERALOCKr: CSTCE12M0G52A-R0
C1=10pF (Typ.)
C2=10pF (Typ.)
V2V1
1MΩ
Continued on the following page.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
Application Circuits Utilization
27
4
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Continued from the preceding page.
■ HD64F36077GH (Renesas)
16-bit Microcomputer
H
11 10 L6
0.1µF
IC : HD64F36077GH
Vcc=5.0V
H: 3, 7, 12
L: 8, 9
CERALOCKr
C1C2CERALOCKr: CSTCE8M00G52-R0
C1=10pF (Typ.)
C2=10pF (Typ.)
V2V1
■ LC87F5G32A (Sanyo)
8-bit Microcomputer
26 H' H 2
6 7 LL'
10kF
2.2kF
IC : LC87F5G32A
Vdd=5.0V
10kΩ10kΩ100pF
47000pF510Ω
H: 8, 19, 39
L: 5, 20, 40
H': 29, 31, 35
L': 30, 32~34, 36
CERALOCKr
C1C2CERALOCKr: CSTLS5M00G53-B0
C1=15pF (Typ.)
C2=15pF (Typ.)
V2V1
■ uPD70F3215HYGC (NEC Electronics)
32-bit Microcomputer
H 14
12 13 L10
IC : µPD70F3215HYGC
Vdd=5.0V
H: 1, 5, 9, 34, 70
L: 2, 8, 11, 33, 69
CERALOCKr
C1C2CERALOCKr: CSTCR5M00G55-R0
C1=39pF (Typ.)
C2=39pF (Typ.)
V2V1
10µF
■ ATmega128 (Atmel)
8-bit Microcomputer
H
24 23 L
IC : ATmega128
Vcc=5.0V
H: 21, 52, 64
L: 22, 53, 63
CERALOCKr
C1C2CERALOCKr: CSTCE8M00G52-R0
C1=10pF (Typ.)
C2=10pF (Typ.)
V2V1
■ ST7FLITE29F2B6 (ST Microelectronics)
8-bit Microcomputer
H 18
15 14 L
IC : ST7FLITE29F2B6
Vdd=5.0V
H: 17
L: 16
CERALOCKr
C1C2CERALOCKr: CSTCE16M0V53-R0
C1=15pF (Typ.)
C2=15pF (Typ.)
V2V1
■ TMS320F2810PBKA (Texas Insturumets)
32-bit Microcomputer
58 57 L
IC : TMS320F2810PBKA
Vdd1=1.8V
CERALOCKr: CSTCE15M0V53-R0
C1=15pF (Typ.)
C2=15pF (Typ.)
Vdd2=3.3V
H1 H2
V2V1
100Ω
CERALOCKr
C1C2
H1: 20, 29, 42, 56, 63, 74, 82, 94, 99,
100, 102, 110, 114
H2: 1, 13, 14, 25, 49, 52, 83, 104, 118
L: 12, 15, 17, 26, 30, 39, 53, 59, 62, 73,
88, 95, 103, 109, 115, 117, 128
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
28
5
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Ceramic Resonators (CERALOCKr)
MHz Lead Type -Standard Frequency Tolerance for General Usage-
MURATA's ceramic resonator, "CERALOCK" with built-in
load capacitors, has been widely applied as the most
suitable component for clock oscillators in a broad
range of microprocessors.
The CSTLS series can be used in the design of
oscillation circuits not requiring external load
capacitors, enabling both high-density mounting and
cost reduction.
■ Features
1. Oscillation circuits do not require external load
capacitors.
There is some variation in built-in capacitance
values applicable to various IC (except for CSALS
series).
2. The series is stable over a wide temperature range.
3. The resonators are compact, lightweight and exhibit
superior shock resistance performance.
4. They enable the design of oscillator circuits
requiring no adjustment.
5. The series is inexpensive and available in stable
supply.
■ Applications
1. DTMF generators
2. Clock oscillators for microcomputers
3. Remote control units
4. Automated office equipment
∗∗∗
∗∗∗ : Weekly Date Code
(in mm)
8.0±1.0 3.0±1.0
5.5±0.5
3.5±0.3
ø0.48±0.05
2.5±0.2
2.5±0.2
0.7 (Ref.)
0.7 (Ref.)0.7 (Ref.)7.0 (Ref.)(3) (2) (1)
CSTLS_G
3.40-10.00MHz
∗
5.5±1.0
2.5±0.2 2.5±0.2
(in mm)
6.5±0.53.5±0.3φ0.48±0.05
T∗1
T∗1
(3) (2) (1) : 3.5±1.0 (16.00—32.99MHz)
3.0±1.0 (33.00—70.00MHz)
∗ : EIAJ Monthly Code
CSTLS_X
16.00-70.00MHz
∗
5.5±1.0 T∗1
T : 3.5±1.0 (16.00—32.99MHz)
3.0±1.0 (33.00—70.00MHz)
∗1
5.0±0.3
6.5±0.53.5±0.3φ0.48±0.05
(in mm)
∗ : EIAJ Monthly Code
CSALS_X
16.00-70.00MHz
Part Number Oscillating
Frequency
(MHz)
Initial
Tolerance Temp. Stability
(%)
Temperature
Range
(°C)
CSTLS_G 3.40 to 10.00 ±0.5% ±0.2
[-0.4% to +0.2%:Built-in Capacitance 47pF type] -20 to 80
CSALS_X 16.00 to 70.00 ±0.5% ±0.2 -20 to 80
CSTLS_X 16.00 to 70.00 ±0.5% ±0.2 -20 to 80
Irregular or stop oscillation may occur under unmatched circuit conditions. Please check the actual conditions prior to use.
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the packaging page.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
29
5
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
■ Oscillation Frequency Measuring Circuit
CSTLS_G/CSTLS_X
Rf
Rd
VDD
C1 C2
To Frequency counter
(1) (3)
(2)
CSALS_X
Rf
Rd
VDD
CL2CL1
To Frequency counter
■ Oscillation Frequency Temperature Stability
CSTLS_G
Oscillating Frequency Shift (%)
Temperature (°C)
Y40
W0.50
W0.25
0
Y0.25
Y0.50
0 40 80 120
CSTLS_X
Temperature (˚C)
Oscillating Frequency Shift (%)
0.3
0.2
0.1
0.0
−0.1
−0.2
−0.3
−50 −30 −10 10 30 50 70 90 110 130
CSALS_X
Temperature (˚C)
Oscillating Frequency Shift (%)
0.3
0.2
0.1
0.0
−0.1
−0.2
−0.3
−50 −30 −10 10 30 50 70 90 110 130
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
30
6
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Ceramic Resonators (CERALOCKr)
kHz Chip Type -Standard Frequency Tolerance for General Usage-
MURATA's original package technologies have enabled
the development of the kHz band "CERALOCK".
The series is perfect in miniature remote control
units and AV modules.
"CERALOCK" can be reflow soldered and mounted by
automatic placers.
■ Features
1. The series withstands reflow soldering.
2. The series is mountable by automatic placers.
3. No adjustment is necessary for oscillation circuits.
■ Applications
1. Clock oscillators for microprocessors
2. OA equipment
3. AV modules
7.5±0.3
1.1±0.1
0.9±0.1
3.3±0.3
0.15±0.05
1.0 max.
0.15 max.
2.0±0.5
8.5±0.3
1.0±0.5
5.0±0.2
0+0.1
-0.4
∗ : EIAJ code
(in mm)
CSBFB_J
430-519kHz
5.0±0.3
0.8±0.2
0.7±0.2
2.5±0.2
2.3±0.2
0.15±0.05
0.10±0.03
1.0 max.
6.0±0.3
2.0±0.5
1.0±0.3
0.15 max.
0+0.1
−0.4
∗ : EIAJ code
(in mm)
CSBFB_J
700-1250kHz
Part Number Oscillating Frequency
(kHz) Initial Tolerance Temp. Stability
(%) Temperature Range
(°C)
CSBFB_J 430 to 519, 700 to 1250 ±0.5% ±0.3 -20 to 80
Irregular or stop oscillation may occur under unmatched circuit conditions. Please check the actual conditions prior to use.
■ Oscillation Frequency Measuring Circuit
Rf
Rd
VDD
CL2CL1
To Frequency counter
■ Oscillation Frequency Temperature Stability
Y40 8040 120
W0.5
0
Y0.5
Temperature (˚C)
0
Oscillating Frequency Shift (%)
Continued on the following page.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
31
6
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Continued from the preceding page.
■ Standard Land Pattern Dimensions
CSBFB_J (430-519kHz)
3.3
1.7 1.7
2.0 0.5
(in mm)
CSBFB_J (700-1250kHz)
1.0
1.5 1.5
3.0 0.5
(in mm)
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
32
7
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Ceramic Resonators (CERALOCKr)
kHz Lead Type -Standard Frequency Tolerance for General Usage-
The CSBLA series ceramic resonators owe their
development to MURATA's innovative expert technologies
and the application of mass production techniques
typically utilized in the manufacture of piezoelectric
ceramic components. Because of their high mechanical Q
and consistent high quality, the CSBLA series are
ideally suited to microprocessor and remote control
unit applications.
■ Features
1. The series is stable over a wide temperature range
and with respect to long-term aging.
2. The series comprises fixed, tuned, solid-state
devices.
3. The resonators are miniature and lightweight.
4. They exhibit excellent shock resistance performance.
5. Oscillating circuits requiring no adjustment can be
designed by utilizing these resonators in
conjunction with transistors or appropriate ICs.
■ Applications
1. Square-wave and sine-wave oscillators
2. Clock generator for microprocessors
3. Remote control systems
7.9±0.3 3.6±0.3
0.8±0.1
1.1±0.1
5.0±0.2
1.8±0.3
0.1±0.03
0.25±0.1
4.3±0.5 9.3±0.3
1.5 max.
∗ : EIAJ code
(in mm)
CSBLA_E
375-429kHz
7.0±0.3 3.5±0.3
0.8±0.1
1.1±0.1
5.0±0.2
1.75±0.5 3.5±0.5 9.0±0.3
0.1±0.03
0.25±0.1 1.5 max.
∗ : EIAJ code
(in mm)
CSBLA_E
430-509kHz
7.0±0.3 3.5±0.3
0.8±0.1
1.1±0.1
5.0±0.2
1.75±0.5 3.5±0.5 9.0±0.3
0.1±0.03
0.25±0.1 1.5 max.
∗ : EIAJ code
(in mm)
CSBLA_E
510-699kHz
1.5 max.
5.0±0.3 2.2±0.2
6.0±0.3
3.5±.0.5
0.8±0.2
2.5±0.2
1.1±0.2
0.6±0.2
0.15±0.05
0.1±0.03
∗ : EIAJ code
in mm
CSBLA_J
700-1250kHz
Part Number Oscillating Frequency
(kHz) Initial Tolerance Temp. Stability
(%) Temperature Range
(°C)
CSBLA_E 375 to 699 - ±0.3 -20 to +80
CSBLA_J 700 to 1250 ±0.5% ±0.3 -20 to 80
Irregular or stop oscillation may occur under unmatched circuit conditions. Please check the actual conditions prior to use.
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the packaging page.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
33
7
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
■ Oscillation Frequency Measuring Circuit
Rf
Rd
VDD
CL2CL1
To Frequency counter
■ Oscillation Frequency Temperature Stability
Y40 8040 120
W0.5
0
Y0.5
Temperature (˚C)
0
Oscillating Frequency Shift (%)
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
One heat stress, shown in the profile at right, is applied to
resonator; then, after being placed in natural conditions
for 1 hour, the resonator is measured.
(a) Pre-heating conditions should be +150 to +180°C for
60 to 120 seconds. Ascending time up to +150°C
should be longer than 30 seconds.
(b) Heating conditions should be within 40 seconds at
+230°C min., but peak temperature should be Iower
than +260°C.
1. Soldering Conditions
(1) Reflow
HCFC, Isopropanol, Tap water, Demineralized water,
Cleanthrough750H, Pine alpha 100S, Techno care FRW
Some series do not withstand washing.
Please check the list at right before use.
2. Wash
3. Notice for Mounting
(1) Cleaning Solvents
dT<=60°C (dT=Component-solvent)
*1 ex. In case the component at +90°C immerses into
cleaning solvent at +60°C, then dT=30°C.
(2) Temperature Difference : dT *1
5 minutes max. by air blow at +80°C max.
(4) Drying
(a) Total washing time should be within 10 minutes.
(b) The component may be damaged if it is washed with
chlorine, petroleum, or alkali cleaning solvent.
(a) The component is recommended for use with
placement machines which employ optical placement
capabilities. The component might be damaged by
excessive mechanical force. Please make sure to
evaluate by using placement machines before going
into mass production. Do not use placement
machines which utilize mechanical positioning. Please
contact Murata for details beforehand.
(b) Please insure the component is thoroughly evaluated
in your application circuit.
(c) Please do not apply excess mechanical stress to the
component and terminals during soldering.
(5) Others
(a) Ultrasonic Wash
1 minute max. in above solvent at +60°C max.
(Frequency: 28kHz, Output: 20W/l)
(b) Immersion Wash
5 minutes max. in above solvent at +60°C max.
(c) Shower or Rinse Wash
5 minutes max. in above solvent at +60°C max.
(3) Conditions
Components shall be measured after soldering on PCB
at +350±5°C for 3.0±0.5 seconds and leaving in natural
condition for 24 hours. The soldering iron shall not touch
the components while soldering.
(2) Soldering Iron
CSTCC (Except 2.00 - 3.49MHz)
CSTCC (Only 2.00 - 3.49MHz)
Series Wash
Available
Not Available
150
230
180
30 sec.
min. 40 sec.
max.
Peak
(260˚C max.)
Pre-heating
(150-180˚C)
Heating
(230˚C)
Gradual
Cooling
120 sec.
min.
60-120 sec.
Temperature (˚C)
■ CSTCC Series
MHz Chip Type Notice (Soldering and Mounting) for General Usage
34
7
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
One heat stress, shown in the profile at right, is applied to
resonator; then, after being placed in natural conditions
for 1 hour, the resonator is measured.
(a) Pre-heating conditions should be +150 to +180°C for
60 to 120 seconds. Ascending time up to +150°C
should be longer than 30 seconds.
(b) Heating conditions should be within 40 seconds at
+230°C min., but peak temperature should be Iower
than +260°C.
1. Soldering Conditions
(1) Reflow
Please contact us in case you need washable component.
2. Wash
3. Notice for Mounting
(a) The component is recommended for use with
placement machines which employ optical placement
capabilities. The component might be damaged by
excessive mechanical force. Please make sure to
evaluate by using placement machines before going
into mass production. Do not use placement machines
which utilize mechanical positioning. Please contact
Murata for details beforehand.
(b) Please insure the component is thoroughly evaluated
in your application circuit.
(c) Please do not apply excess mechanical stress to the
component and terminals during soldering.
Components shall be measured after soldering on PCB
at +350±5°C for 3.0±0.5 seconds and leaving in natural
condition for 24 hours. The soldering iron shall not touch
the components while soldering.
(2) Soldering Iron
150
230
180
30 sec.
min. 40 sec.
max.
Peak
(260˚C max.)
Pre-heating
(150-180˚C)
Heating
(230˚C)
Gradual
Cooling
120 sec.
min.
60-120 sec.
Temperature (˚C)
■ CSTCR/CSTCE_V/CSTCG/CSTCE_G/CSTCE_XK Series
MHz Chip Type Notice (Soldering and Mounting) for General Usage
35
7
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
One heat stress, shown in the profile at right, is applied to
resonator; then, after being placed in natural conditions
for 1 hour, the resonator is measured.
(a) Pre-heating conditions should be +150 to +180°C for
60 to 120 seconds. Ascending time up to +150°C
should be longer than 30 seconds.
(b) Heating conditions should be within 40 seconds at
+230°C min., but peak temperature should be Iower
than +260°C.
1. Soldering Conditions
(1) Reflow
HCFC, Isopropanol, Tap water, Demineralized water,
Cleanthrough750H, Pine alpha 100S, Techno care FRW
2. Wash
3. Notice for Mounting
(1) Cleaning Solvents
dT<=60°C (dT=Component-solvent)
*1 ex. In case the component at +90°C immerses into
cleaning solvent at +60°C, then dT=30°C.
(2) Temperature Difference : dT *1
5 minutes max. by air blow at +80°C max.
(4) Drying
(a) Total washing time should be within 10 minutes.
(b) The component may be damaged if it is washed with
chlorine, petroleum, or alkali cleaning solvent.
(a) The component is recommended for use with
placement machines which employ optical placement
capabilities. In some cases, placement machines
which utilize mechanical positioning may apply
excessive mechanical force which might result in
damage to the ceramic resonator. Please contact
Murata before mounting this product using placement
machines which use mechanical positioning.
(b) Please insure the component is thoroughly evaluated
in your application circuit.
(c) Please do not apply excess mechanical stress to the
component and terminals during soldering.
(5) Others
(a) Ultrasonic Wash
1 minute max. in above solvent at +60°C max.
(Frequency: 28kHz, Output: 20W/l)
(b) Immersion Wash
5 minutes max. in above solvent at +60°C max.
(c) Shower or Rinse Wash
5 minutes max. in above solvent at +60°C max.
(3) Conditions
Components shall be measured after soldering on PCB
at +350±5°C for 3.0±0.5 seconds and leaving in natural
condition for 24 hours. The soldering iron shall not touch
the components while soldering.
(2) Soldering Iron
150
230
180
30 sec.
min. 40 sec.
max.
Peak
(260˚C max.)
Pre-heating
(150-180˚C)
Heating
(230˚C)
Gradual
Cooling
120 sec.
min.
60-120 sec.
Temperature (˚C)
■ CSTCV/CSACV Series
MHz Chip Type Notice (Soldering and Mounting) for General Usage
36
7
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
One heat stress, shown in the profile at right, is applied to
resonator; then, after being placed in natural conditions
for 1 hour, the resonator is measured.
(a) Pre-heating conditions should be +150 to +180°C for
60 to 120 seconds. Ascending time up to +150°C
should be longer than 30 seconds.
(b) Heating conditions should be within 40 seconds at
+230°C min., but peak temperature should be Iower
than +260°C.
1. Soldering Conditions
(1) Reflow
Please contact us in case you need washable component.
2. Wash
3. Notice for Mounting
(a) Please insure the component is thoroughly evaluated
in your application circuit.
(b) Please do not apply excess mechanical stress to the
component and terminals during soldering.
Components shall be measured after soldering on PCB
at +350±5°C for 3.0±0.5 seconds and leaving in natural
condition for 24 hours. The soldering iron shall not touch
the components while soldering.
(2) Soldering Iron
150
230
180
30 sec.
min. 40 sec.
max.
Peak
(260˚C max.)
Pre-heating
(150-180˚C)
Heating
(230˚C)
Gradual
Cooling
120 sec.
min.
60-120 sec.
Temperature (˚C)
■ CSACW/CSTCW/CSTCZ Series
MHz Chip Type Notice (Soldering and Mounting) for General Usage
37
7
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
MHz Chip Type Notice for General Usage
38
7
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
■ Notice (Storage and Operating Conditions)
■ Notice (Rating)
The component may be damaged if excess mechanical
stress is applied.
■ Notice (Handling)
"CERALOCK" may stop oscillating or oscillate
irregularly under improper circuit conditions.
1. Product Storage Condition
Please store the products in room where the
temperature/humidity is stable. And avoid
such places where there are large temperature
changes. Please store the products under the
following conditions:
Temperature: -10 to + 40 degrees C
Humidity: 15 to 85% R.H.
2. Expire Date on Storage
Expire date (Shelf life) of the products is six
months after delivery under the conditions of a
sealed and an unopened package. Please use the
products within six months after delivery. If you
store the products for a long time (more than six
months), use carefully because the products may
be degraded in the solderability and/or rusty.
Please confirm solderability and characteristics
for the products regularly.
3. Notice on Product Storage
(1) Please do not store the products in a chemical
atmosphere (Acids, Alkali, Bases, Organic gas,
Sulfides and so on), because the characteristics
may be reduced in quality, and/or be degraded in
the solderability due to the storage in a
chemical atmosphere.
(2) Please do not put the products directly on the
floor without anything under them to avoid damp
places and/or dusty places.
(3) Please do not store the products in the places
such as: in a damp heated place, in a place where
direct sunlight comes in, in place applying
vibrations.
(4) Please use the products immediately after the
package is opened, because the characteristics
may be reduced in quality, and/or be degraded in
the solderability due to storage under the poor
condition.
(5) Please do not drop the products to avoid cracking
of ceramic element.
4. Others
Conformal coating or washing of the component is not
acceptable because it is not hermetically sealed.
Please be sure to consult with our sales representative
or engineer whenever and prior to using the products.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
MHz Lead Type Notice for General Usage
39
7
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
■ Notice (Soldering and Mounting)
1. Soldering Conditions
(1) Reflow
The component cannot withstand reflow soldering.
(2) Soldering Iron
(a) Lead terminals are immersed up to 1.5 mm from
components body in soldering bath of +260+-5
degrees C for 10+-1.0 seconds, and then
components shall be left in natural condition
for 1 hour.
(b) Lead terminal is directly contacted with the tip
of soldering iron of +350+-5 degrees C
for 3.0+-0.5 seconds, and then components shall
be left in natural condition for 1 hour.
(3) Please do not apply excessive mechanical stress to
the component and lead terminals during soldering.
2. Wash
The component cannot withstand washing.
■ Notice (Storage and Operating Conditions)
■ Notice (Rating)
The component may be damaged if excess mechanical
stress is applied.
■ Notice (Handling)
"CERALOCK" may stop oscillating or oscillate
irregularly under improper circuit conditions.
1. Product Storage Condition
Please store the products in room where the
temperature/humidity is stable. And avoid
such places where there are large temperature
changes. Please store the products under the
following conditions:
Temperature: -10 to + 40 degrees C
Humidity: 15 to 85% R.H.
2. Expire Date on Storage
Expire date (Shelf life) of the products is six
months after delivery under the conditions of a
sealed and an unopened package. Please use the
products within six months after delivery. If you
store the products for a long time (more than six
months), use carefully because the products may
be degraded in the solderability and/or rusty.
Please confirm solderability and characteristics
for the products regularly.
3. Notice on Product Storage
(1) Please do not store the products in a chemical
atmosphere (Acids, Alkali, Bases, Organic gas,
Sulfides and so on), because the characteristics
may be reduced in quality, and/or be degraded in
the solderability due to the storage in a
chemical atmosphere.
(2) Please do not put the products directly on the
floor without anything under them to avoid damp
places and/or dusty places.
(3) Please do not store the products in the places
such as: in a damp heated place, in a place where
direct sunlight comes in, in place applying
vibrations.
(4) Please use the products immediately after the
package is opened, because the characteristics
may be reduced in quality, and/or be degraded in
the solderability due to storage under the poor
condition.
(5) Please do not drop the products to avoid cracking
of ceramic element.
4. Others
Conformal coating or washing of the component is not
acceptable because it is not hermetically sealed.
Please be sure to consult with our sales representative
or engineer whenever and prior to using the products.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
One heat stress, shown in the profile at right, is applied to
resonator; then, after being placed in natural conditions
for 1 hour, the resonator is measured.
(a) Pre-heating conditions should be +150 to +180°C for
60 to 120 seconds. Ascending time up +150°C should
be longer than 30 seconds.
(b) Heating conditions should be within 40 seconds at
+230°C min., but peak temperature should be lower
than +260°C.
1. Soldering Conditions
(1) Reflow
HCFC, Isopropanol, Tap water, Demineralized water,
Cleanthrough750H, Pine alpha 100S, Techno care FRW
2. Wash
3. Notice for Mounting
(1) Cleaning Solvents
dT<=60°C (dT=Component-solvent)
*1 ex. In case the component at +90°C immerses into
cleaning solvent at +60°C, then dT=30°C.
(2) Temperature Difference : dT *1
5 minutes max. by air blow at +80°C max.
(4) Drying
(a) Total washing time should be within 10 minutes.
(b) The component may be damaged if it is washed with
chlorine, petroleum, or alkali cleaning solvent.
(c) Ultrasonic cleaning of the component is acceptable.
However, the size of bath, size and thickness of PCB
should be evaluated to confirm stable electrical
characteristics are maintained.
(5) Others
(a) Ultrasonic Wash
1 minute max. in above solvent at +60°C max.
(Frequency: 28kHz, Output: 20W/l)
(b) Immersion Wash
5 minutes max. in above solvent at +60°C max.
(c) Shower or Rinse Wash
5 minutes max. in above solvent at +60°C max.
(3) Conditions
Components shall be measured after soldering on PCB
at +350±5°C for 3.0±0.5 seconds and leaving in natural
condition for 24 hours. The soldering iron shall not touch
the components while soldering.
(2) Soldering Iron
(a) Please insure the component is thoroughly evaluated
in your application circuit.
(b) Please do not apply excess mechanical stress to the
component and lead terminals during soldering.
(c) In the case of the bulk component, dry heating
treatment (130°C. for 5 hours min.) is required before
reflow soldering. Then, the component should be
soldered within 48 hours after dry heating treatment.
150
230
180
30 sec.
min. 40 sec.
max.
Peak
(260˚C max.)
Pre-heating
(150-180˚C)
Heating
(230˚C)
Gradual
Cooling
120 sec.
min.
60-120 sec.
Temperature (˚C)
■ Notice (Soldering and Mounting)
CSBFB_J (430-519kHz/700-1250kHz)
kHz Type Notice for General Usage
40
7
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
kHz Type Notice for General Usage
41
7
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
■ Notice (Soldering and Mounting)
CSBLA_E
1. Soldering Conditions
(1) Reflow
The component cannot withstand reflow soldering.
(2) Soldering Iron
(a) Lead terminals are immersed up to 1.5 mm from
components body in soldering bath of +260+-5
degrees C for 10+-1.0 seconds, and then
components shall be left in natural condition
for 1 hour.
(b) Lead terminal is directly contacted with the tip
of soldering iron of +350+-5 degrees C
for 3.0+-0.5 seconds, and then components shall
be left in natural condition for 1 hour.
(3) Please do not apply excessive mechanical stress to
the component and lead terminals during soldering.
2. Wash
The component cannot withstand washing.
■ Notice (Soldering and Mounting)
CSBLA_J
■ Notice (Storage and Operating Condition)
CSBFB_J/CSBLA_J
Continued on the following page.
1. Product Storage Condition
Please store the products in room where the
temperature/humidity is stable. And avoid
such places where there are large temperature
changes. Please store the products under the
following conditions:
Temperature: -10 to + 40 degrees C
Humidity: 15 to 85% R.H.
2. Expire Date on Storage
Expire date (Shelf life) of the products is six
months after delivery under the conditions of a
sealed and an unopened package. Please use the
products within six months after delivery. If you
store the products for a long time (more than six
months), use carefully because the products may
be degraded in the solderability and/or rusty.
Please confirm solderability and characteristics
for the products regularly.
3. Notice on Product Storage
(1) Please do not store the products in a chemical
atmosphere (Acids, Alkali, Bases, Organic gas,
Sulfides and so on), because the characteristics
may be reduced in quality, and/or be degraded in
the solderability due to the storage in a
chemical atmosphere.
(2) Please do not put the products directly on the
floor without anything under them to avoid damp
places and/or dusty places.
(3) Please do not store the products in the places
such as: in a damp heated place, in a place where
direct sunlight comes in, in place applying
vibrations.
(4) Please use the products immediately after the
package is opened, because the characteristics
may be reduced in quality, and/or be degraded in
the solderability due to storage under the poor
condition.
(5) Please do not drop the products to avoid cracking
of ceramic element.
(1) Cleaning Solvents
HCFC, Isopropanol, Tap water, Demineralized water,
Cleanthrough750H, Pine alpha 100S, Techno care
FRW.
(2) Temperature Difference: dT *1
dT<=30 C. (dT=Component-solvent)
*1 ex. In case the component at +90 degrees C. immerses
into cleaning solvent at +60 degrees C., then
dT=30 degrees C.
(3) Conditions
1. Ultrasonic Wash
1 minute max. in above solvent at +60 degrees C. max.
(Frequency: 28kHz, Output: 20W/L)
2. Immersion Wash
5 minutes max. in above solvent at +60 degrees C. max.
3. Shower or Rinse Wash
5 minutes max. in above solvent at +60 degrees C. max.
(4) Drying
5 minutes max. by air blow at +80 degrees C. max.
(5) Others
1. Total washing time should be within 10 minutes.
2. Please insure the component is thoroughly
evaluated in your application circuit.
3. The component may be damaged if it is washed
with alkali cleaning solvent.
4. Please do not apply excess mechanical stress to
the component and lead terminals during soldering.
5. Ultrasonic cleaning of the component is acceptable.
However, the size of bath, size and thickness of
PBC should be evaluated to confirm stable electrical
characteristics are maintained.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
kHz Type Notice for General Usage
42
7
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Continued from the preceding page.
■ Notice (Storage and Operating Condition)
CSBLA_E
■ Notice (Rating)
The component may be damaged if excess mechanical
stress is applied.
■ Notice (Handling)
"CERALOCK" may stop oscillating or oscillate
irregularly under improper circuit conditions.
4. Others
Conformal coating of the component is acceptable.
However, the resin material, curing temperature, and
other process conditions should be evaluated to
confirm that stable electrical characteristics are
maintained.
Please be sure to consult with our sales representative
or engineer whenever and prior to using the products.
1. Product Storage Condition
Please store the products in room where the
temperature/humidity is stable. And avoid
such places where there are large temperature
changes. Please store the products under the
following conditions:
Temperature: -10 to + 40 degrees C
Humidity: 15 to 85% R.H.
2. Expire Date on Storage
Expire date (Shelf life) of the products is six
months after delivery under the conditions of a
sealed and an unopened package. Please use the
products within six months after delivery. If you
store the products for a long time (more than six
months), use carefully because the products may
be degraded in the solderability and/or rusty.
Please confirm solderability and characteristics
for the products regularly.
3. Notice on Product Storage
(1) Please do not store the products in a chemical
atmosphere (Acids, Alkali, Bases, Organic gas,
Sulfides and so on), because the characteristics
may be reduced in quality, and/or be degraded in
the solderability due to the storage in a
chemical atmosphere.
(2) Please do not put the products directly on the
floor without anything under them to avoid damp
places and/or dusty places.
(3) Please do not store the products in the places
such as: in a damp heated place, in a place where
direct sunlight comes in, in place applying
vibrations.
(4) Please use the products immediately after the
package is opened, because the characteristics
may be reduced in quality, and/or be degraded in
the solderability due to storage under the poor
condition.
(5) Please do not drop the products to avoid cracking
of ceramic element.
4. Others
Conformal coating or washing of the component is not
acceptable because it is not hermetically sealed.
Please be sure to consult with our sales representative
or engineer whenever and prior to using the products.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
MHz Chip Type Packaging for General Usage
43
7
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
■ Minimum Quantity
(in mm)
a b
CSTCC_G
CSTCR_G
CSTCR_G15L
CSTCE_G
CSTCE_G15L
CSTCE_V
CSTCE_V13L
CSTCE_XK
CSTCE_XT
CSTCG_V
CSTCZ_X12R
CSTCW_X
CSTCW_X11
CSTCW_X_M
CSACW_X
Part Number Plastic Tape ø180mm Plastic Tape ø330mm Bulk Dimensions
2,000
3,000
3,000
3,000
3,000
3,000
3,000
3,000
3,000
3,000
3,000
3,000
3,000
3,000
3,000
6,000
9,000
9,000
9,000
9,000
9,000
9,000
9,000
9,000
9,000
9,000
9,000
9,000
9,000
9,000
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
a
a
a
b
b
b
b
b
b
b
b
b
b
b
b
(ø180 )
17.0±1.0
ø13.0±0.2 2.0±0.5
160-190
Trailer Leader
Empty
400-560
Cover Film
Components
Trailer
160-190
Empty
160 min.
Empty
160 min.
400-560
Cover Film
Leader
Empty Components
ø13.0±0.2 2.0±0.5
+1.0
–0
9.0
13.0±1.0
(pcs.)
c Dimensions of Reel
The order quantity should be an integral multiple of the "Minimum Quantity" shown above.
13.0
+1.0
0
0
–1.5
(ø180 )
0
–1.5
■ Dimensions of Taping
CSTCR_G15
(in mm)
4.0±0.1 2.0±0.05
(9.5)
4.0±0.1
(3) (2) (1)
ø1.5W0.1
Y0
ø1.5W0.1
Y0
12.0±0.2
5.5±0.05 1.75±0.1
4.7±0.1
0.3±0.05
1.25±0.05
(1.85 max.)
2.2±0.1
Direction of Feed
3˚ max.
10˚ Cover Film
The cover film peel strength force 0.1 to 0.7N
The cover film peel speed 300mm/min.
CSTCE_G15L
(in mm)
2.0±0.05
4.0±0.1
3° max.
3.5±0.05
8.0±0.2
1.75±0.1
0.25±0.05
0.90±0.10
(1.30 max.)
10°
(5.2)
Cover Film
Direction of Feed
The cover film peel strength force 0.1 to 0.7N
The cover film peel speed 300mm/min.
4.0±0.1
1.50±0.1
ø1.5 -0.0
+0.1
ø1.0 -0.0
+0.2
3.40±0.1
(3) (2) (1)
Continued on the following page.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
MHz Chip Type Packaging for General Usage
44
7
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Continued from the preceding page.
■ Dimensions of Taping
CSTCE_V13L
Dimensions of Carrier Tape
(in mm)
4.0±0.1
Cover Film
4.0±0.1
2.0±0.05
8.0±0.2
ø1.5
+0.1
-0.0
ø1.0
+0.1
-0.0
3.5±0.05 1.75±0.1
3.45±0.1
Direction of Feed
0.25±0.05
(1.40 max.)
1.10±0.05
3˚ max.
1.50±0.1
The cover film peel strength force 0.1 to 0.7N
The cover film peel speed 300mm/min.
10˚
(5.2)
(2)(3) (1)
CSTCE_XK, CSTCE_XT
(in mm)
2.0±0.05
4.0±0.1
3° max.
3.5±0.05
8.0±0.2
1.75±0.1
0.25±0.05
1.15±0.1
(1.50 max.)
10°
(5.2)
Cover Film
Direction of Feed
The cover film peel strength force 0.1 to 0.7N
The cover film peel speed 300mm/min.
4.0±0.1
1.50±0.1
ø1.5 -0.0
+0.1
ø1.0 -0.0
+0.2
3.40±0.1
(3) (2) (1)
CSTCW_X11
(in mm)
Thickness of CERALOCKr
∗1, ∗2 : Dimensions vary with product thickness of CERALOCKr
1.40–1.20 1.15–1.00 0.95–0.90
t1 ∗1
t2 ∗21.48±0.1
2.1 max. 1.30±0.1
1.9 max. 1.12±0.1
1.7 max.
4.0±0.1
2.8±0.1
3.5±0.1 1.75±0.1
(1)(3) (2)
8.0±0.2
0.2±0.1
t2
t1
∗2
∗1
(5.5)
2.0±0.1
4.0±0.1
3° max.
10°Cover Film
The cover film peel strength force 0.1 to 0.7N
The cover film peel speed 300mm/min.
+0.1
-
0.0
ø1.5
+0.1
-
0.05
2.3
+0.2
-
0.0
ø1.0
Direction of Feed
CSTCZ-X12R
(in mm)
4.0±0.1
2.2±0.1
3.5±0.1 1.75±0.1
(1)(3) (2)
8.0±0.2
0.2±0.1
1.6 max.
1.10±0.1
(5.5)
2.0±0.1
4.0±0.1
3° max.
10°Cover Film
The cover film peel strength force 0.1 to 0.7N
The cover film peel speed 300mm/min.
+0.1
-0.0
ø1.5
1.8±0.1
+0.2
-0.0
ø1.0
Direction of Feed
CSTCC_G less than 3.00MHz
(in mm)
4.0±0.1 2.0±0.05
+0.3
-0.0
ø1.55±0.05
ø1.5
1.75±0.1
5.5±0.05
12.0±0.2
7.6±0.1
4.0±0.1
(9.5)
3.3±0.1
The cover film peel strength force 0.1 to 0.7N
The cover film peel speed 300mm/min. Cover film
10˚
3˚max.
1.85±0.05
0.3±0.05
(2.45 max.)
Direction of Feed
(3) (2) (1)
CSTCC_G more than 3.00MHz
(in mm)
4.0±0.1 2.0±0.05
+0.3
-0.0
φ1.55±0.05
φ1.5
1.75±0.1
5.5±0.05
12.0±0.2
7.6±0.1
4.0±0.1
(9.5)
(1)(2)(3)
3.3±0.1
The cover film peel strength force 0.1 to 0.7N
The cover film peel speed 300mm/min. Cover film
10˚
3˚max.
1.65±0.05
0.3±0.05
(2.25 max.)
Direction of Feed
Continued on the following page.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
MHz Chip Type Packaging for General Usage
45
7
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Continued from the preceding page.
■ Dimensions of Taping
CSTCR_G
(in mm)
4.0±0.1 2.0±0.05
(9.5)
4.0±0.1
(3) (2) (1)
ø1.5W0.1
Y0
ø1.5W0.1
Y0
12.0±0.2
5.5±0.05 1.75±0.1
4.7±0.1
0.3±0.05
1.25±0.05
(1.85 max.)
2.2±0.1
Direction of Feed
3˚ max.
10˚ Cover Film
The cover film peel strength force 0.1 to 0.7N
The cover film peel speed 300mm/min.
CSTCE_G
(in mm)
2.0±0.05
4.0±0.1
3° max.
3.5±0.05
8.0±0.2
1.75±0.1
0.25±0.05
0.90±0.10
(1.30 max.)
10°
(5.2)
Cover Film
Direction of Feed
The cover film peel strength force 0.1 to 0.7N
The cover film peel speed 300mm/min.
4.0±0.1
1.50±0.1
ø1.5 -0.0
+0.1
ø1.0 -0.0
+0.2
3.40±0.1
(3) (2) (1)
CSTCE_V
Dimensions of Carrier Tape
(in mm)
4.0±0.1
Cover Film
4.0±0.1
2.0±0.05
8.0±0.2
ø1.5
+0.1
-0.0
ø1.0
+0.1
-0.0
3.5±0.05 1.75±0.1
3.45±0.1
Direction of Feed
0.25±0.05
(1.40 max.)
1.10±0.05
3˚ max.
1.50±0.1
The cover film peel strength force 0.1 to 0.7N
The cover film peel speed 300mm/min.
10˚
(5.2)
(2)(3) (1)
CSTCG_V
(in mm)
4.0±0.1
Dimensions of Carrier Tape
Cover Film
4.0±0.1
2.0±0.05
8.0±0.2
ø1.5
+0.1
-0.0
ø1.0
+0.1
-0.0
3.5±0.05 1.75±0.1
2.2±0.05
Direction of Feed
0.25±0.05
(1.30 max.)
1.00±0.05
3˚ max.
1.50±0.1
The cover film peel strength force 0.1 to 0.7N
The cover film peel speed 300mm/min.
10˚
(5.2)
(2)(3) (1)
CSACW_X
(in mm)
Thickness of CERALOCKr
∗1, ∗2 : Dimensions vary with product thickness of CERALOCKr
1.40–1.20 1.15–1.00 0.95–0.90
t1 ∗1
t2 ∗21.48±0.1
2.1 max. 1.30±0.1
1.9 max. 1.12±0.1
1.7 max.
4.0±0.1
2.8±0.1
3.5±0.1 1.75±0.1
8.0±0.2
0.3±0.1
t2
t1
(5.5)
2.0±0.1
4.0±0.1
3° max.
10°Cover Film
The cover film peel strength force 0.1 to 0.7N
The cover film peel speed 300mm/min.
+0.1
-
0.0
ø1.5
+0.1
-
0.05
2.3
+0.2
-
0.0
ø1.0
Direction of Feed
∗1
∗2
CSTCW_X
(in mm)
Thickness of CERALOCKr
∗1, ∗2 : Dimensions vary with product thickness of CERALOCKr
1.40–1.20 1.15–1.00 0.95–0.90
t1 ∗1
t2 ∗21.48±0.1
2.1 max. 1.30±0.1
1.9 max. 1.12±0.1
1.7 max.
4.0±0.1
2.8±0.1
3.5±0.1 1.75±0.1
(1)(3) (2)
8.0±0.2
0.2±0.1
t2
t1
∗2
∗1
(5.5)
2.0±0.1
4.0±0.1
3° max.
10°Cover Film
The cover film peel strength force 0.1 to 0.7N
The cover film peel speed 300mm/min.
+0.1
-
0.0
ø1.5
+0.1
-
0.05
2.3
+0.2
-
0.0
ø1.0
Direction of Feed
CSTCW_X_M
(in mm)
∗1, ∗2 : Dimensions vary with product thickness of CERALOCKr
1.40–1.20 1.15–1.00 0.95–0.70
t1 ∗1
t2 ∗21.48±0.1
2.1 max. 1.30±0.1
1.9 max. 1.12±0.1
1.7 max.
4.0±0.1
2.8±0.1
3.5±0.1 1.75±0.1
(1)(3) (2)
8.0±0.2
0.2±0.1
t2
t1
∗2
∗1
(5.5)
2.0±0.1
4.0±0.1
3° max.
10°Cover Film
The cover film peel strength force 0.1 to 0.7N
The cover film peel speed 300mm/min.
+0.1
-0.0
ø1.5
2.3±0.1
+0.2
-0.0
ø1.0
Thickness of CERALOCKr
Direction of Feed
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
MHz Lead Type Packaging for General Usage
46
7
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
■ Minimum Quantity
Part Number Ammo Pack
(pcs.)
The order quantity should be an integral multiple of the "Minimum Quantity" shown above.
Bulk
500
500
CSTLS_G (3.40 to 10.0MHz) 2,000
CSTLS_X (16.00 to 70.00MHz) 2,000
■ Tape Dimensions of CSTLS_G
(in mm)
Width of diameter
Height of resonator
Dimensions of terminal
Lead length under the hold down tape
Pitch of component
Pitch of sprocket hole
Length from sprocket hole center to lead
Length from sprocket hole center to
component center
Lead spacing (I)
Lead spacing (II)
Slant forward or backward
Width of carrier tape
Width of hold down tape
Position of sprocket hole
Gap of hold down tape and carrier tape
Distance between the center of
sprocket hole and lead stopper
Total height of resonator
Diameter of sprocket hole
Total tape thickness
Body tilt
Item Code Dimensions Tolerance Remarks
D
A
d
L1
P
P0
P1
P2
F1
F2
dh
W
W0
W1
W2
H0
H1
D0
t
dS
8.0
5.5
ø0.48
5.0 min.
12.7
12.7
3.85
6.35
2.5
2.5
0
18.0
6.0 min.
9.0
0
18.0
23.5
ø4.0
0.6
0
±1.0
±0.5
±0.05
–
±0.5
±0.2
±0.5
±0.5
±0.2
±0.2
±1.0
±0.5
–
±0.5
±0.5
±1.0
±0.2
±0.2
±1.0
Tolerance for Pitches 10xP0=127±1
1mm max.
Hold down tape does not exceed the carrier tape.
W0.5
Y0
M∗M∗∗ ∗∗ ∗
P2
D
A
P
dS
W
H0
H1
W1
W0
L1
W2
D0
t
P0
P1F1F2
Direction of Feed
dh dh
d
Continued on the following page.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
MHz Lead Type Packaging for General Usage
47
7
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Continued from the preceding page.
■ Tape Dimensions of CSTLS_X
(in mm)
Width of diameter
Height of resonator
Dimensions of terminal
Lead length under the hold down tape
Pitch of component
Pitch of sprocket hole
Length from sprocket hole center to lead
Length from sprocket hole center to
component center
Lead spacing (I)
Lead spacing (II)
Slant forward or backward
Width of carrier tape
Width of hold down tape
Position of sprocket hole
Gap of hold down tape and carrier tape
Distance between the center of
sprocket hole and lead stopper
Total height of resonator
Diameter of sprocket hole
Total tape thickness
Body tilt
Item Code Dimensions Tolerance Remarks
D
A
d
L1
P
P0
P1
P2
F1
F2
dh
W
W0
W1
W2
H0
H1
D0
t
dS
5.5
6.5
ø0.48
5.0 min.
12.7
12.7
3.85
6.35
2.5
2.5
0
18.0
6.0 min.
9.0
0
18.0
24.5
ø4.0
0.6
0
±1.0
±0.5
±0.05
–
±0.5
±0.2
±0.5
±0.5
±0.2
±0.2
±1.0
±0.5
–
±0.5
±0.5
±1.0
±0.2
±0.2
±1.0
Tolerance for Pitches 10xP0=127±1
1mm max.
Hold down tape does not exceed the carrier tape.
W0.5
Y0.0
D dS
d
P2P
A
W0
L1
W1
W2
H0
H1
P1
P0t
F1F2
W
D0
dh dh
Direction of Feed
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
MHz Lead Type Packaging for General Usage
48
7
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
■ Minimum Quantity
CSALS_X (16.00 to 70.00MHz)
Part Number Ammo Pack
2,000
Bulk
500
(pcs.)
The order quantity should be an integral multiple of the "Minimum Quantity" shown above.
■ Tape Dimensions of CSALS
(in mm)
Width of diameter
Height of resonator
Dimensions of terminal
Lead length under the hold down tape
Pitch of component
Pitch of sprocket hole
Length from sprocket hole center to lead
Length from sprocket hole center to
component center
Lead spacing
Slant forward or backward
Width of carrier tape
Width of hold down tape
Position of sprocket hole
Gap of hold down tape and carrier tape
Distance between the center of
sprocket hole and lead stopper
Total height of resonator
Diameter of sprocket hole
Total tape thickness
Body tilt
Item Code Dimensions Tolerance Remarks
D
A
d
L1
P
P0
P1
P2
F
dh
W
W0
W1
W2
H0
H1
D0
t
dS
5.5
6.5
ø0.48
5.0 min.
12.7
12.7
3.85
6.35
5.0
0
18.0
6.0 min.
9.0
0
18.0
24.5
ø4.0
0.6
0
±1.0
±0.5
±0.05
———
±0.5
±0.2
±0.5
±0.5
±0.3
±1.0
±0.5
———
±0.5
±0.5
±1.0
±0.2
±0.2
±1.0
Tolerance for Pitches 10xP0=127±1
1mm max.
Hold down tape does not exceed the carrier tape.
+0.5
-0
D dS
d
P2P
A
W0
L1
W1
W2
H0
H1
P1
P0t
F
W
D0
dh dh
Direction of Feed
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
kHz Type Packaging for General Usage
49
7
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
■ CSBFB Series Minimum Quantity
(in mm)
CSBFB_J (430 to 519kHz)
CSBFB_J (700 to 1250kHz)
Part Number BulkPlastic Tape ø330mm
1,500
3,000
500
1,000
ø13.0±0.2
2.0±0.5
(ø80±1.0)
(ø330±2.0)
17.5±0.5
21.5±1.0
(pcs.)
The order quantity should be an integral multiple of the "Minimum Quantity" shown above.
c Dimensions of Reel
■ Dimensions of Taping
CSBFB_J 430-519kHz
(in mm)
4.0±0.1
13.3±0.1
11.4±0.1
t0.3
3.5±0.1
(4.6max.)
7.5±0.1
16.0±0.3
1.75±0.1
2.0±0.1
12.0±0.1
8.05±0.1
Direction of Feed
Cover Film 3˚ max.
10˚
ø1.5±0.1
The cover film peel strength force 0.1 to 0.7N
The cover film peel speed 300mm/min.
CSBFB_J 700-1250kHz
(in mm)
4.0±0.1
13.3±0.1
8.8±0.1
t0.3
2.7±0.1
(3.07max.)
7.5±0.1
16.0±0.15
1.75±0.15
2.0±0.1
8.0±0.1
5.45±0.1
Direction of Feed
Cover Film 3˚ max.
10˚
ø1.5±0.1
The cover film peel strength force 0.1 to 0.7N
The cover film peel speed 300mm/min.
■ CSBLA Series Minimum Quantity
CSBLA_E
CSBLA_J
Part Number Magazine
50
100
Bulk
500
1,000
(pcs.)
The order quantity should be an integral multiple of the "Minimum Quantity" shown above.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note P16E.pdf
08.3.3
