TEA1762T/N2,118 - NXP Semiconductors / Philips Semiconductors

1. General description

The TEA1762T is a member of the new generation of Synchronous Rectiﬁer (SR)

controller ICs for switched mode power supplies. Its high level of integration allows the

design of a cost-effective power supply with a very low number of external components.

The TEA1762T is a controller IC dedicated for synchronous rectiﬁcation on the secondary

side of discontinuous conduction mode and quasi resonant ﬂyback converters. Besides

electronics for synchronous rectiﬁcation, it also has integrated circuitry for output voltage

and output current regulation.

The TEA1762T is fabricated in a Silicon On Insulator (SOI) process. This NXP SOI

process makes possible a wide range of operation.

2. Features

2.1 Distinctive features

nCombined synchronous rectiﬁcation and primary feedback control functionality

nWide supply voltage range (8.6 V to 38 V)

nHigh level of integration, resulting in a very low external component count

nWide opto output voltage range (3.5 V to 38 V)

nAccurate internal voltage reference for voltage control (within 1 %)

nSeparate sense ground for accurate voltage sensing

nHigh driver output voltage of 10 V to drive all MOSFET brands to the lowest RDSon

nReference voltage output pin

2.2 Green features

nLow current consumption

nHigh system efﬁciency from no load to full load

2.3 Protection features

nUndervoltage protection

nInternal over-temperature protection

nGeneral purpose protection input pin

TEA1762T

GreenChip synchronous rectiﬁer controller

Rev. 02 — 25 April 2007 Product data sheet

Product data sheet Rev. 02 — 25 April 2007 2 of 15

NXP Semiconductors TEA1762T

GreenChip synchronous rectiﬁer controller

3. Applications

nThe TEA1762T is intended for adapters. The device can also be used in all other

discontinuous conduction mode and quasi resonant ﬂyback systems that demand a

highly efﬁcient and cost-effective solution.

4. Ordering information

5. Block diagram

Table 1. Ordering information

Type number Package

Name Description Version

TEA1762T SO14 plastic small outline package; 14 leads; body width 3.9 mm SOT108-1

Fig 1. TEA1762T block diagram

014aaa059

50 mV

OVER

TEMPERATURE

PROTECTION

VCC

OPTOPROT

ISENSE

5, 12, 13

n.c.

SENSEGND

SRSENSE 1

2.5 V

OPTOREG VSENSE

VREF

810

1.25 V

DRIVER

control

PROTECT

POWERGND

TIMER

2 µs

2.2 µs −310 mV −12 mV −55 mV

Product data sheet Rev. 02 — 25 April 2007 3 of 15

NXP Semiconductors TEA1762T

GreenChip synchronous rectiﬁer controller

6. Pinning information

6.1 Pinning

6.2 Pin description

7. Functional description

The TEA1762T is the controller for synchronous rectiﬁcation to be used in discontinuous

conduction mode and quasi resonant ﬂyback converters. Besides controlling the

SR MOSFET, the TEA1762T contains the voltage reference and ampliﬁers to regulate and

control the output voltage and output current of the power supply.

Fig 2. Pin conﬁguration TEA1762T

TEA1762T

SRSENSE VCC

POWERGND n.c.

SENSEGND n.c.

PROTECT ISENSE

n.c. VSENSE

DRIVER VREF

OPTOPROT OPTOREG

001aae773

7 8

Table 2. Pin description for SO14

Symbol Pin Description

SRSENSE 1 synchronous timing input

POWERGND 2 power ground

SENSEGND 3 sense ground

PROTECT 4 general purpose protection input

n.c. 5 not connected

DRIVER 6 driver output for SR MOSFET

OPTOPROT 7 opto coupler driver output for current protection

OPTOREG 8 opto coupler driver output for voltage regulation

VREF 9 reference voltage output

VSENSE 10 sense input for voltage control

ISENSE 11 sense input for current control

n.c. 12 not connected

n.c. 13 not connected

VCC 14 supply voltage

Product data sheet Rev. 02 — 25 April 2007 4 of 15

NXP Semiconductors TEA1762T

GreenChip synchronous rectiﬁer controller

7.1 Start-up and undervoltage lock-out

The IC leaves the under-voltage lock-out state and activates the synchronous rectiﬁer

circuitry and also the voltage/current sense circuitry as soon as the voltage on the VCC pin

is above 8.6 V (typical). As soon as the voltage drops below 8.1 V (typical), the

under-voltage lock-out state is re-entered and the SR driver output is actively kept low and

also the opto driver outputs are disabled.

7.2 Synchronous rectiﬁcation

After a negative voltage (−310 mV typical) is sensed on the SRSENSE pin, the driver

output voltage is made high and the external MOSFET is switched on. As soon as the

SRSENSE voltage rises to −55 mV, the driver output voltage is regulated to maintain the

−55 mV on the SRSENSE pin. As soon as the SRSENSE voltage is above −12 mV, the

driver output is pulled to ground. After switch-on of the SR MOSFET, the input signal on

the SRSENSE pin is blanked for 2 µs (typical). This will eliminate false switch-off due to

high frequency ringing at the start of the secondary stroke.

Because the driver output voltage is reduced as soon as the voltage on the SRSENSE pin

is −55 mV, the external power switch can be switched off fast when the current through the

switch reaches zero. With this zero-current switch off, no separate standby mode is

needed to maintain high efﬁciency during no-load operation. The zero current is detected

by sensing a −12 mV level on the SRSENSE pin. See Figure 3.

If the secondary stroke of the ﬂyback converter is shorter than 2 µs (typical), the driver

output is disabled. This will guarantee stable operation for very low duty cycles. When the

secondary stroke increases above 2.2 µs (typical), the driver output is again enabled.

Fig 3. Synchronous rectiﬁcation

014aaa057

0 V

−12 mV

−55 mV

−310 mV

0 A

0 V

VSRSENSE

VDRIVER

Primary

current

Secondary

current

Product data sheet Rev. 02 — 25 April 2007 5 of 15

NXP Semiconductors TEA1762T

GreenChip synchronous rectiﬁer controller

7.3 SMPS output voltage and current regulation

The output voltage of the ﬂyback Switched Mode Power Supply (SMPS) can be controlled

by sensing the output voltage via the VSENSE pin. The feedback loop via the primary

controller can regulate the output voltage of the switched mode power supply by

regulating the voltage on the VSENSE pin to 2.5 V above the voltage on pin SENSEGND.

Also the output current of the ﬂyback SMPS can be controlled or limited. The voltage on

the ISENSE pin is regulated or limited to 50 mV above the voltage on pin POWERGND.

7.4 Opto outputs

The opto output is intended to drive an opto coupler (see Figure 5). The opto outputs have

an open drain output conﬁguration. The maximum sink current is internally limited to 5 mA

(typical). The outputs are linearly controlled via the VSENSE and ISENSE input pins. An

over-temperature situation will switch the protection opto output (OPTOPROT) to its

maximum sink current.

During start-up (VCC <V

startup) and undervoltage lock-out the outputs are disabled.

7.5 Protection input

The PROTECT pin is a general purpose input pin which can be used for additional

protection of the switched mode power supply. With a Negative Temperature Coefﬁcient

(NTC) thermistor external temperature protection can be provided, e.g. the external power

switches and transformer can be protected against high temperatures. With a Zener diode

a secondary overvoltage protection can be made.

7.6 Reference voltage output

The reference voltage output pin can be used for supplying external circuitry. The

maximum output current must be limited to 1 mA.

The reference voltage is activated as soon as the start-up voltage is reached on the VCC

pin and switched off again after the VCC pin voltage drops below the VCC stop level.

7.7 Supply management

All (internal) reference voltages are derived from a temperature compensated, on-chip

band gap circuit. The reference voltage is trimmed to an accuracy within 1 %.

7.8 OverTemperature Protection (OTP)

The IC provides an accurate internal overtemperature protection of 150 °C (typical). The

IC will maximize the current of pin OPTOPROT as soon as the internal temperature limit is

reached. The opto signal can be used on the primary side of the ﬂyback controller to

activate the SMPS protection or limit the output power. As soon as the overtemperature

condition is solved, normal operation will resume.

Product data sheet Rev. 02 — 25 April 2007 6 of 15

NXP Semiconductors TEA1762T

GreenChip synchronous rectiﬁer controller

7.9 Driver

The driver circuit to the gate of the external power MOSFET has a source capability of

typically 250 mA and a sink capability of typically 2.7 A. This permits fast turn-on and

turn-off of the power MOSFET for efﬁcient operation. The output voltage of the driver is

limited to 10 V (typical). This high output voltage will drive all MOSFET brands to the

minimum on-state resistance.

During start-up conditions (VCC <V

startup) and undervoltage lock-out the driver output

voltage is actively pulled low.

7.10 Power ground and sense ground

The TEA1762T has two ground connections. The sense ground ensures an increased

accuracy of the output voltage of the switched mode power supply and can also be used

to compensate for cable losses on the output of the converter. The grounds are internally

connected via two anti-parallel diodes.

8. Limiting values

Table 3. Limiting values

In accordance with the Absolute Maximum Rating System (IEC 60134). All voltages are measured with respect to power

ground (pin 2); positive currents ﬂow into the chip. The voltage ratings are valid provided other ratings are not violated; current

ratings are valid provided the maximum power rating is not violated.

Symbol Parameter Conditions Min Max Unit

Voltages

VCC supply voltage continuous −0.4 +38 V

VOPTOREG voltage on pin OPTOREG continuous −0.4 +38 V

VOPTOPROT voltage on pin OPTOPROT continuous −0.4 +38 V

VSRSENSE voltage on pin SRSENSE continuous - +120 V

VVSENSE voltage on pin VSENSE continuous −0.4 +5 V

VISENSE voltage on pin ISENSE −0.4 +5 V

VPROTECT voltage on pin PROTECT −0.4 +5 V

VSENSEGND voltage on pin SENSEGND [1] −0.4 +0.4 V

Currents

IOPTOREG current on pin OPTOREG - +6 mA

IOPTOPROT current on pin OPTOPROT - +6 mA

IDRIVER current on pin DRIVER duty cycle < 10 % −0.8 +3 A

IVREF current on pin VREF −2- mA

ISRSENSE current on pin SRSENSE −3- mA

General

Ptot total power dissipation Tamb <80°C - 0.65 W

Tstg storage temperature −55 +150 °C

Tjjunction temperature −20 +150 °C

Product data sheet Rev. 02 — 25 April 2007 7 of 15

NXP Semiconductors TEA1762T

GreenChip synchronous rectiﬁer controller

[1] Voltages on pin SENSEGND less than +1.0 V will not damage the IC when the duration is limited to 100 µs, but voltages on pin

SENSEGND larger than +0.4 V may lead to disturbed IC operation.

[2] Equivalent to discharging a 100 pF capacitor through a 1.5 kΩ series resistor.

[3] Equivalent to discharging a 200 pF capacitor through a 0.75 µH coil and a 10 Ω resistor.

9. Thermal characteristics

The graph in Figure 4 shows the relationship between junction temperature and VSENSE

voltage.

ESD

VESD electrostatic discharge voltage class 2

human body model [2] - 2000 V

machine model [3] - 200 V

charged device model - 500 V

Table 3. Limiting values

…continued

In accordance with the Absolute Maximum Rating System (IEC 60134). All voltages are measured with respect to power

ground (pin 2); positive currents ﬂow into the chip. The voltage ratings are valid provided other ratings are not violated; current

ratings are valid provided the maximum power rating is not violated.

Symbol Parameter Conditions Min Max Unit

Table 4. Thermal characteristics

Symbol Parameter Conditions Typ Unit

Rth(j-a) thermal resistance from

junction to ambient in free air 100 K/W

Fig 4. Typical regulated VSENSE voltage versus junction temperature

junction temperature (°C)

−50 150100050

001aae779

2480

2520

2440

2600

regulated

VSENSE

voltage

(mV)

2400

Product data sheet Rev. 02 — 25 April 2007 8 of 15

NXP Semiconductors TEA1762T

GreenChip synchronous rectiﬁer controller

10. Characteristics

Table 5. Characteristics

amb

=25

C; V

= 20 V; all voltages are measured with respect to sense ground (pin 3); currents are positive when ﬂowing

into the IC; unless otherwise speciﬁed.

Symbol Parameter Conditions Min Typ Max Unit

Supply voltage management (pin VCC)

Vstartup start-up voltage 8.35 8.6 8.85 V

Vhys hysteresis voltage [1] - 0.5 - V

ICC(oper) operating supply current VCC =8V; V

CC <V

startup -1-mA

under normal operation;

no load on pin DRIVER - 1.4 - mA

Synchronous rectiﬁcation sense input (pin SRSENSE)

Vact(drv) driver activation voltage w.r.t. power ground −340 −310 −280 mV

Vreg(drv) driver regulation voltage w.r.t. power ground −65 −55 −45 mV

Vdeact(drv) driver deactivation voltage w.r.t. power ground −12 mV

td(act)(drv) driver activation delay time 125 ns

tact(sr)(min) minimum synchronous rectiﬁcation

active time Short time 1.5 2 2.5 µs

Long time 1.7 2.2 2.7 µs

Driver (pin DRIVER)

Isource source current VCC = 15 V; voltage on pin

DRIVER=2V −0.3 −0.25 −0.2 A

Isink sink current VCC =15V

voltage on pin DRIVER = 2 V 1 1.4 - A

voltage on pin DRIVER = 9.5 V 2.2 2.7 - A

Vo(max) maximum output voltage VCC =15V - 10 12 V

Opto output (pin OPTOREG and OPTOPROT)

IO(max) maximum output current VOPTO >5V 456mA

VO(min) minimum output voltage IOPTO = 4 mA 3.5 V

Voltage sense (pin VSENSE)

Vreg(VSENSE) regulation voltage on pin VSENSE See Figure 4 2.475 2.5 2.525 V

II(VSENSE) input current on pin VSENSE VVSENSE =V

reg(VSENSE) −100 0 +100 nA

gmtransconductance VVSENSE to IOPTOREG 40 A/V

GB gain bandwidth product RL=1kΩ1 MHz

Reference voltage (pin VREF)

VVREF voltage on pin VREF 2.465 2.5 2.535 V

IVREF current on pin VREF −1mA

CVREF(max) maximum capacitance on pin

VREF 40 pF

Current sense (pin ISENSE)

Vreg(ISENSE) regulation voltage on pin ISENSE w.r.t. power ground;

VPOWERGND >−0.4 V 46 50 54 mV

II(reg)(ISENSE) regulation input current on pin

ISENSE VISENSE =V

reg(ISENSE) −200 −100 0 nA

gmtransconductance VISENSE to IOPTOPROT 8 A/V

Product data sheet Rev. 02 — 25 April 2007 9 of 15

NXP Semiconductors TEA1762T

GreenChip synchronous rectiﬁer controller

[1] The VCC stop voltage is Vstartup − Vhys.

GB gain bandwidth product RL=1kΩ1 MHz

Protection input (pin PROTECT)

Vth(PROTECT) threshold voltage on pin

PROTECT 1.15 1.25 1.35 V

Vhys hysteresis voltage 15 30 45 mV

II(PROTECT) input current on pin PROTECT VPROTECT = Vth(PROTECT) −100 −50 −5nA

Temperature protection

Tpl(max) maximum protection level

temperature 140 150 - °C

Tpl(hys) protection level hysteresis

temperature -12-°C

Table 5. Characteristics

…continued

amb

=25

C; V

= 20 V; all voltages are measured with respect to sense ground (pin 3); currents are positive when ﬂowing

into the IC; unless otherwise speciﬁed.

Symbol Parameter Conditions Min Typ Max Unit

Product data sheet Rev. 02 — 25 April 2007 10 of 15

NXP Semiconductors TEA1762T

GreenChip synchronous rectiﬁer controller

11. Application information

A switched mode power supply with the TEA1762T consists of a primary side

discontinuous conduction mode ﬂyback controller, a transformer, and an output stage with

a feedback circuit. In the output stage a MOSFET (Qsec) is used for low conduction

losses. The MOSFET is controlled by the TEA1762T. The output voltage and/or current is

also controlled by the TEA1762T via the opto coupler connection to the primary side. See

Figure 5.

The output voltage is set by resistors Rfb1 and Rfb2. The output current is controlled by the

resistor Risense. The timing for the synchronous rectiﬁer switch is derived from the voltage

sensed on the SRSENSE pin. The resistor in the SRSENSE connection is needed to

protect the TEA1762T from excessive voltages. The SRSENSE resistor should typically

be 1 kΩ. Higher values might impair correct timing, lower values may not provide sufﬁcient

protection.

During output short circuit or load connection, the limiting values on pin SENSEGND must

not be exceeded.

Fig 5. Application example TEA1762T

014aaa058

DRIVER

SRSENSE

OPTOPROT VCC OPTOREG

VSENSE

Vout

ISENSEPOWERGND

TEA1762T

PRIMARY

SIDE

CONTROLLER

OPTO1

OPTO2

Vin

Qprim Qsec

Ropto

Rfb1

−t

Rfb2

Cout

Cfb

Rsrsense

Risense

SENSEGND

PROTECT

VREF

Product data sheet Rev. 02 — 25 April 2007 11 of 15

NXP Semiconductors TEA1762T

GreenChip synchronous rectiﬁer controller

12. Test information

12.1 Quality information

The

General Quality Speciﬁcation for Integrated Circuits, SNW-FQ-611

is applicable.

Product data sheet Rev. 02 — 25 April 2007 12 of 15

NXP Semiconductors TEA1762T

GreenChip synchronous rectiﬁer controller

13. Package outline

Fig 6. Package outline SOT108-1 (SO14)

UNIT A

max. A1A2A3bpcD

(1) E(1) (1)

ELL

pQZywv θ

REFERENCES

OUTLINE

VERSION EUROPEAN

PROJECTION ISSUE DATE

IEC JEDEC JEITA

inches

1.75 0.25

0.10 1.45

1.25 0.25 0.49

0.36 0.25

0.19 8.75

8.55 4.0

3.8 1.27 6.2

5.8 0.7

0.6 0.7

0.3 8

0.25 0.1

DIMENSIONS (inch dimensions are derived from the original mm dimensions)

Note

1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included.

1.0

0.4

SOT108-1

detail X

vMA

(A )

076E06 MS-012

pin 1 index

0.069 0.010

0.004 0.057

0.049 0.01 0.019

0.014 0.0100

0.0075 0.35

0.34 0.16

0.15 0.05

1.05

0.041

0.244

0.228 0.028

0.024 0.028

0.012

0.01

0.25

0.01 0.004

0.039

0.016

99-12-27

03-02-19

0 2.5 5 mm

scale

SO14: plastic small outline package; 14 leads; body width 3.9 mm SOT108-1

Product data sheet Rev. 02 — 25 April 2007 13 of 15

NXP Semiconductors TEA1762T

GreenChip synchronous rectiﬁer controller

14. Revision history

Table 6. Revision history

Document ID Release date Data sheet status Change notice Supersedes

TEA1762T_2 20070425 Product data sheet - TEA1762T_1

Modiﬁcations: •Updated limiting values for ISRSENSE in Table 3.

•Updated characteristic values for Isource,I

sink, GB (voltage and current sense) and Tpl(max) in

Table 5.

•Soldering section removed.

•The format of this data sheet has been redesigned to comply with the new identity guidelines

of NXP Semiconductors.

•Legal texts have been adapted to the new company name where appropriate.

TEA1762T_1 20060331 Objective data sheet - -

Product data sheet Rev. 02 — 25 April 2007 14 of 15

NXP Semiconductors TEA1762T

GreenChip synchronous rectiﬁer controller

15. Legal information

15.1 Data sheet status

[1] Please consult the most recently issued document before initiating or completing a design.

[2] The term ‘short data sheet’ is explained in section “Deﬁnitions”.

[3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status

information is available on the Internet at URL http://www.nxp.com.

15.2 Deﬁnitions

Draft — The document is a draft version only. The content is still under

internal review and subject to formal approval, which may result in

modiﬁcations or additions. NXP Semiconductors does not give any

representations or warranties as to the accuracy or completeness of

information included herein and shall have no liability for the consequences of

use of such information.

Short data sheet — A short data sheet is an extract from a full data sheet

with the same product type number(s) and title. A short data sheet is intended

for quick reference only and should not be relied upon to contain detailed and

full information. For detailed and full information see the relevant full data

sheet, which is available on request via the local NXP Semiconductors sales

ofﬁce. In case of any inconsistency or conﬂict with the short data sheet, the

full data sheet shall prevail.

15.3 Disclaimers

General — Information in this document is believed to be accurate and

reliable. However, NXP Semiconductors does not give any representations or

warranties, expressed or implied, as to the accuracy or completeness of such

information and shall have no liability for the consequences of use of such

information.

Right to make changes — NXP Semiconductors reserves the right to make

changes to information published in this document, including without

limitation speciﬁcations and product descriptions, at any time and without

notice. This document supersedes and replaces all information supplied prior

to the publication hereof.

Suitability for use — NXP Semiconductors products are not designed,

authorized or warranted to be suitable for use in medical, military, aircraft,

space or life support equipment, nor in applications where failure or

malfunction of a NXP Semiconductors product can reasonably be expected to

result in personal injury, death or severe property or environmental damage.

NXP Semiconductors accepts no liability for inclusion and/or use of NXP

Semiconductors products in such equipment or applications and therefore

such inclusion and/or use is at the customer’s own risk.

Applications — Applications that are described herein for any of these

products are for illustrative purposes only. NXP Semiconductors makes no

representation or warranty that such applications will be suitable for the

speciﬁed use without further testing or modiﬁcation.

Limiting values — Stress above one or more limiting values (as deﬁned in

the Absolute Maximum Ratings System of IEC 60134) may cause permanent

damage to the device. Limiting values are stress ratings only and operation of

the device at these or any other conditions above those given in the

Characteristics sections of this document is not implied. Exposure to limiting

values for extended periods may affect device reliability.

Terms and conditions of sale — NXP Semiconductors products are sold

subject to the general terms and conditions of commercial sale, as published

at http://www.nxp.com/proﬁle/terms, including those pertaining to warranty,

intellectual property rights infringement and limitation of liability, unless

explicitly otherwise agreed to in writing by NXP Semiconductors. In case of

any inconsistency or conﬂict between information in this document and such

terms and conditions, the latter will prevail.

No offer to sell or license — Nothing in this document may be interpreted

or construed as an offer to sell products that is open for acceptance or the

grant, conveyance or implication of any license under any copyrights, patents

or other industrial or intellectual property rights.

15.4 Trademarks

Notice: All referenced brands, product names, service names and trademarks

are the property of their respective owners.

GreenChip — is a trademark of NXP B.V.

16. Contact information

For additional information, please visit: http://www.nxp.com

For sales ofﬁce addresses, send an email to: salesaddresses@nxp.com

Document status[1][2] Product status[3] Deﬁnition

Objective [short] data sheet Development This document contains data from the objective speciﬁcation for product development.

Preliminary [short] data sheet Qualiﬁcation This document contains data from the preliminary speciﬁcation.

Product [short] data sheet Production This document contains the product speciﬁcation.

NXP Semiconductors TEA1762T

GreenChip synchronous rectiﬁer controller

For more information, please visit: http://www.nxp.com

For sales office addresses, please send an email to: salesaddresses@nxp.com

Date of release: 25 April 2007

Document identifier: TEA1762T_2

Please be aware that important notices concerning this document and the product(s)

described herein, have been included in section ‘Legal information’.

17. Contents

1 General description. . . . . . . . . . . . . . . . . . . . . . 1

2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

2.1 Distinctive features . . . . . . . . . . . . . . . . . . . . . . 1

2.2 Green features . . . . . . . . . . . . . . . . . . . . . . . . . 1

2.3 Protection features . . . . . . . . . . . . . . . . . . . . . . 1

3 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

4 Ordering information. . . . . . . . . . . . . . . . . . . . . 2

5 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 2

6 Pinning information. . . . . . . . . . . . . . . . . . . . . . 3

6.1 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

6.2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3

7 Functional description . . . . . . . . . . . . . . . . . . . 3

7.1 Start-up and undervoltage lock-out . . . . . . . . . 4

7.2 Synchronous rectiﬁcation . . . . . . . . . . . . . . . . . 4

7.3 SMPS output voltage and current regulation . . 5

7.4 Opto outputs. . . . . . . . . . . . . . . . . . . . . . . . . . . 5

7.5 Protection input. . . . . . . . . . . . . . . . . . . . . . . . . 5

7.6 Reference voltage output . . . . . . . . . . . . . . . . . 5

7.7 Supply management. . . . . . . . . . . . . . . . . . . . . 5

7.8 OverTemperature Protection (OTP) . . . . . . . . . 5

7.9 Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

7.10 Power ground and sense ground . . . . . . . . . . . 6

8 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 6

9 Thermal characteristics. . . . . . . . . . . . . . . . . . . 7

10 Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . 8

11 Application information. . . . . . . . . . . . . . . . . . 10

12 Test information. . . . . . . . . . . . . . . . . . . . . . . . 11

12.1 Quality information . . . . . . . . . . . . . . . . . . . . . 11

13 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 12

14 Revision history. . . . . . . . . . . . . . . . . . . . . . . . 13

15 Legal information. . . . . . . . . . . . . . . . . . . . . . . 14

15.1 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 14

15.2 Deﬁnitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

15.3 Disclaimers. . . . . . . . . . . . . . . . . . . . . . . . . . . 14

15.4 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 14

16 Contact information. . . . . . . . . . . . . . . . . . . . . 14

17 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15