54F169,74F169 54F169 74F169 4-Stage Synchronous Bidirectional Counter Literature Number: SNOS161A 54F/74F169 4-Stage Synchronous Bidirectional Counter General Description Features The 'F169 is a fully synchronous 4-stage up/down counter. The 'F169 is a modulo-16 binary counter. Features a preset capability for programmable operation, carry lookahead for easy cascading and a U/D input to control the direction of counting. All state changes, whether in counting or parallel loading, are initiated by the LOW-to-HIGH transition of the clock. Y Package Number Military Y Asynchronous counting and loading Built-in lookahead carry capability Presettable for programmable operation e Commercial Y Package Description N16E 16-Lead (0.300x Wide) Molded Dual-In-Line J16A 16-Lead Ceramic Dual-In-Line 74F169SC (Note 1) M16A 16-Lead (0.150x Wide) Molded Small Outline, JEDEC 74F169SJ (Note 1) M16D 16-Lead (0.300x Wide) Molded Small Outline, EIAJ et 74F169PC 54F169DM (Note 2) Note 1: Devices also available in 13x reel. Use suffix e SCX and SJX. bs ol Note 2: Military grade device with environmental and burn-in processing. Use suffix e DMQB. Logic Symbols IEEE/IEC 'F169 O TL/F/9488 - 3 TL/F/9488 - 9 TRI-STATEE is a registered trademark of National Semiconductor Corporation. C1995 National Semiconductor Corporation TL/F/9488 RRD-B30M75/Printed in U. S. A. 54F/74F169 4-Stage Synchronous Bidirectional Counter November 1994 Connection Diagrams Pin Assignment for DIP, SOIC and Flatpak Pin Assignment for LCC TL/F/9488-1 TL/F/9488 - 2 54F/74F U.L. HIGH/LOW Input IIH/IIL Output IOH/IOL Count Enable Parallel Input (Active LOW) Count Enable Trickle Input (Active LOW) Clock Pulse Input (Active Rising Edge) Parallel Data Inputs Parallel Enable Input (Active LOW) Up-Down Count Control Input Flip-Flop Outputs Terminal Count Output (Active LOW) 1.0/1.0 1.0/2.0 1.0/1.0 1.0/1.0 1.0/1.0 1.0/1.0 50/33.3 50/33.3 20 mA/b0.6 mA 20 mA/b1.2 mA 20 mA/b0.6 mA 20 mA/b0.6 mA 20 mA/b0.6 mA 20 mA/b0.6 mA b 1 mA/20 mA b 1 mA/20 mA bs ol CEP CET CP P0 - P3 PE U/D Q0 - Q3 TC Description et Pin Names e Unit Loading/Fan Out Functional Description CET is LOW, when a counter reaches zero in the Count Down mode or reaches 15 for the 'F169 in the Count Up mode. The TC output state is not a function of the Count Enable Parallel (CEP) input level. Since the TC signal is derived by decoding the flip-flop states, there exists the possibility of decoding spikes on TC. For this reason the use of TC as a clock signal is not recommended (see logic equations below). 1) Count Enable e CEP # CET # PE The 'F169 uses edge-triggered J-K type flip-flops and has no constraints on changing the control or data input signals in either state of the clock. The only requirement is that the various inputs attain the desired state at least a setup time before the rising edge of the clock and remain valid for the recommended hold time thereafter. The parallel load operation takes precedence over other operations, as indicated in the Mode Select Table. When PE is LOW, the data on the P0 - P3 inputs enters the flip-flops on the next rising edge of the clock. In order for counting to occur, both CEP and CET must be LOW and PE must be HIGH; the U/D input then determines the direction of counting. The Terminal Count (TC) output is normally HIGH and goes LOW, provided that O 2) Up: ('F169): TC e Q0 # Q1 # Q2 # Q3 # (Up) # CET 3) Down: TC e Q0 # Q1 # Q2 # Q3 # (Down) # CET 2 Logic Diagram bs ol et e 'F169 TL/F/9488 - 5 Please note that these diagrams are provided only for the understanding of logic operations and should not be used to estimate propagation delays. Mode Select Table PE CEP CET U/D Action on Rising Clock Edge L H H H H X L L H X X L L X H X H L X X Load (Pn x Qn) Count Up (Increment) Count Down (Decrement) No Change (Hold) No Change (Hold) State Diagram O 'F169 TL/F/9488 - 7 3 H e HIGH Voltage Level L e LOW Voltage Level X e Immaterial Absolute Maximum Ratings (Note 1) Recommended Operating Conditions If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/Distributors for availability and specifications. Storage Temperature b 65 C to a 150 C Ambient Temperature under Bias Junction Temperature under Bias Plastic b 55 C to a 125 C Free Air Ambient Temperature Military Commercial b 55 C to a 125 C 0 C to a 70 C Supply Voltage Military Commercial b 55 C to a 175 C b 55 C to a 150 C a 4.5V to a 5.5V a 4.5V to a 5.5V VCC Pin Potential to Ground Pin b 0.5V to a 7.0V b 0.5V to a 7.0V Input Voltage (Note 2) b 30 mA to a 5.0 mA Input Current (Note 2) Voltage Applied to Output in HIGH State (with VCC e 0V) b 0.5V to VCC Standard Output b 0.5V to a 5.5V TRI-STATEE Output Current Applied to Output in LOW State (Max) twice the rated IOL (mA) e Note 1: Absolute maximum ratings are values beyond which the device may be damaged or have its useful life impaired. Functional operation under these conditions is not implied. DC Electrical Characteristics Symbol 54F/74F Parameter Min VIH Input HIGH Voltage VIL Input LOW Voltage VCD Input Clamp Diode Voltage VOH Output HIGH Voltage 54F 10% VCC 74F 10% VCC 74F 5% VCC VOL Output LOW Voltage 54F 10% VCC 74F 10% VCC IIH Input HIGH Current IBVI et Note 2: Either voltage limit or current limit is sufficient to protect inputs. 2.0 Typ Units VCC Conditions Max V Recognized as a HIGH Signal V Recognized as a LOW Signal bs ol 0.8 V Min IIN e b18 mA V Min IOH e b1 mA IOH e b1 mA IOH e b1 mA 0.5 0.5 V Min IOL e 20 mA IOL e 20 mA 54F 74F 20.0 5.0 mA Max VIN e 2.7V Input HIGH Current Breakdown Test 54F 74F 100 7.0 mA Max VIN e 7.0V ICEX Output HIGH Leakage Current 54F 74F 250 50 mA Max VOUT e VCC VID Input Leakage Test 74F V 0.0 IID e 1.9 mA All Other Pins Grounded IOD Output Leakage Circuit Current 74F 3.75 mA 0.0 VIOD e 150 mV All Other Pins Grounded IIL Input LOW Current b 0.6 b 1.2 mA Max VIN e 0.5V (except CET) VIN e 0.5V (CET) IOS Output Short-Circuit Current b 150 mA Max VOUT e 0V ICCL Power Supply Current 52 mA Max VO e LOW O b 1.2 2.5 2.5 2.7 4.75 b 60 35 4 'F169 AC Electrical Characteristics Symbol Parameter 74F 54F 74F TA e a 25 C VCC e a 5.0V CL e 50 pF TA, VCC e Mil CL e 50 pF TA, VCC e Com CL e 50 pF Min Typ Max Min Max Min Max fmax Maximum Count Frequency 90 tPLH tPHL Propagation Delay CP to Qn (PE HIGH or LOW) 3.0 4.0 6.5 9.0 8.5 11.5 3.0 4.0 12.0 16.0 3.0 4.0 9.5 13.0 ns tPLH tPHL Propagation Delay CP to TC 5.5 4.0 12.0 8.5 15.5 12.5 5.5 4.0 20.0 15.0 5.5 4.0 17.5 13.0 ns tPLH tPHL Propagation Delay CET to TC 2.5 2.5 4.5 8.5 6.5 11.0 2.5 2.5 9.0 12.0 2.5 2.5 7.0 12.0 ns tPLH tPHL Propagation Delay U/D to TC 3.5 4.0 8.5 8.0 11.5 12.0 3.5 4.0 16.0 14.0 3.5 4.0 12.5 13.0 ns AC Operating Requirements ts(H) ts(L) th(H) th(L) ts(H) ts(L) th(H) th(L) ts(H) ts(L) th(H) th(L) ts(H) ts(L) Setup Time, HIGH or LOW Pn to CP tw(H) tw(L) 74F TA, VCC e Mil TA, VCC e Com Min Min Min 4.0 4.0 Max Max 4.5 4.5 4.5 4.5 Hold Time, HIGH or LOW Pn to CP 3.0 3.0 3.5 3.5 3.5 3.5 Setup Time, HIGH or LOW CEP or CET to CP 7.0 5.0 8.0 8.0 8.0 6.5 Hold Time, HIGH or LOW CEP or CET to CP 0 0.5 0 1.0 0 0.5 Setup Time, HIGH or LOW PE to CP 8.0 8.0 10.0 10.0 9.0 9.0 Hold Time, HIGH or LOW PE to CP 1.0 0 1.0 0 1.0 0 Setup Time, HIGH or LOW U/D to CP 11.0 7.0 14.0 12.0 12.5 8.5 Hold Time, HIGH or LOW U/D to CP 0 0 0 0 0 0 4.0 7.0 6.0 9.0 4.5 8.0 O th(H) th(L) Parameter 54F TA e a 25 C VCC e a 5.0V bs ol Symbol CP Pulse Width HIGH or LOW MHz et 74F 70 e 60 Units 5 Units Max ns ns ns ns ns Ordering Information The device number is used to form part of a simplified purchasing code where the package type and temperature range are defined as follows: 74F 169 S Temperature Range Family 74F e Commercial 54F e Military C X Special Variations X e Devices shipped in 13x reels QB e Military grade device with environmental and burn-in processing shipped in tubes Device Type Package Code P e Plastic DIP D e Ceramic DIP S e Small Outline Package SOIC JEDEC SJ e Small Outline SOIC EIAJ Temperature Range C e Commercial (0 C to a 70 C) M e Military (b55 C to a 125 C) bs ol et e Physical Dimensions inches (millimeters) O 16-Lead Ceramic Dual-In-Line Package (D) NS Package Number J16A 6 et e Physical Dimensions inches (millimeters) (Continued) O bs ol 16-Lead (0.150x Wide) Molded Small Outline Package, JEDEC (S) NS Package Number M16A 16-Lead (0.300x Wide) Molded Dual-In-Line Package (P) NS Package Number N16E 7 e et 16-Lead (0.300x Wide) Molded Small Outline Package, EIAJ (SJ) NS Package Number M16D bs ol 54F/74F169 4-Stage Synchronous Bidirectional Counter Physical Dimensions inches (millimeters) (Continued) LIFE SUPPORT POLICY O NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation 2900 Semiconductor Drive P.O. Box 58090 Santa Clara, CA 95052-8090 Tel: 1(800) 272-9959 TWX: (910) 339-9240 National Semiconductor GmbH Livry-Gargan-Str. 10 D-82256 F4urstenfeldbruck Germany Tel: (81-41) 35-0 Telex: 527649 Fax: (81-41) 35-1 National Semiconductor Japan Ltd. Sumitomo Chemical Engineering Center Bldg. 7F 1-7-1, Nakase, Mihama-Ku Chiba-City, Ciba Prefecture 261 Tel: (043) 299-2300 Fax: (043) 299-2500 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Hong Kong Ltd. 13th Floor, Straight Block, Ocean Centre, 5 Canton Rd. Tsimshatsui, Kowloon Hong Kong Tel: (852) 2737-1600 Fax: (852) 2736-9960 National Semiconductores Do Brazil Ltda. Rue Deputado Lacorda Franco 120-3A Sao Paulo-SP Brazil 05418-000 Tel: (55-11) 212-5066 Telex: 391-1131931 NSBR BR Fax: (55-11) 212-1181 National Semiconductor (Australia) Pty, Ltd. Building 16 Business Park Drive Monash Business Park Nottinghill, Melbourne Victoria 3168 Australia Tel: (3) 558-9999 Fax: (3) 558-9998 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated