EE1001 - OMRON - Product.Network

CSM_EE-SPX303N_403N_DS_E_3_3

Broad Slot-type Photomicrosensor

EE-SPX303N/403N

A Wide Slot Width of 13 mm and

Superior Resistance to Light

Interference and Noise.

•

Noise resistance equivalent to photomicrosensors with built-in amplifiers.

• Resistance to common noise at least 30 times that of previous models.

• Resistance to inverter noise at least 10 times that of previous models.

• Reverse polarity protection built in.

Be sure to read Safety Precautions on

page 3.

For the most recent information on models that have been certified for

safety standards, refer to your OMRON website.

Ordering Information

Sensors

Accessories (Order Separately)

Note: Refer to Accessories for details.

* EE-1009- or EE-1010-series Connectors have a builtin locking mechanism to prevent cable disconnection when only the cable is pulled. To remove the Connector

from the Sensor, grip the top and bottom of the Connector firmly and push into the Sensor once before pulling out. The locking mechanism prevents the Connector

from being removed by pulling on the cable only and enables removal only when the Connector (housing) is pulled.

Appearance Sensing method Sensing distance

(slot width) Output type Output

configuration Model

Through-beam type

(with slot) NPN output

Dark-ON EE-SPX303N

Light-ON EE-SPX403N

Type Cable length Model

Connector EE-1001

EE-1009 *

Connector with

Cable

1 m EE-1006 1M

EE-1010 1M *

2 m EE-1006 2M

EE-1010 2M *

Connector with

Robot Cable

1 m EE-1010-R 1M *

2 m EE-1010-R 2M *

NPN/PNP Conversion Connector 0.46 m (total length) EE-2002

Infrared light

13 mm

(slot width)

EE-SPX303N/403N

Ratings and Specifications

Engineering Data (Reference Value)

Sensing Position Characteristics

EE-SPX303N

Item Models EE-SPX303N, EE-SPX403N

Sensing distance 13 mm (slot width)

Sensing object Opaque: 2.2 × 0.5 mm min.

Differential distance 0.05 mm max.

Light source Infrared LED (pulse lighting) with a peak wavelength of

940 nm

Indicator Light indicator (red)

Supply voltage 12 to 24 VDC ±10%, ripple (p-p): 5% max.

Current consumption 15 mA max.

Control output

NPN voltage output:

Load power supply voltage: 12 to 24 VDC

Load current: 80 mA max.

OFF current: 0.5 mA max.

80 mA load current with a residual voltage of 2.0 V max.

10 mA load current with a residual voltage of 1.0 V max.

Protection circuits Power supply reverse polarity protection,

Output reverse polarity protection

Response frequency *100 Hz min.

Ambient illumination 3,000 lx max. with incandescent light or sunlight on the surface of

the receiver.

Ambient temperature

range

Operating: −10 to +55°C

Storage: −25 to +65°C

Ambient humidity range Operating: 5% to 85%

Storage: 5% to 95%

Vibration resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 h each

in X, Y, and Z directions

Shock resistance Destruction: 500 m/s2 for 3 times each in X, Y, and Z directions

Degree of protection IEC IP50

Connecting method Special connector (soldering not possible)

Weight Approx. 4 g

Material Polycarbonate

* The response frequency was measured by

detecting the following rotating disk.

2 mm

Disk

2 mm

0 1 2 3 4 5 6

Distance d

(

)

Tr ON

Tr OFF

Dark-ON

0 1 2 3 4 5 6

Distance d

(

)

Tr ON

Tr OFF

Dark-ON

EE-SPX303N/403N

I/O Circuit Diagrams

NPN Output

Safety Precautions

Refer to Warranty and Limitations of Liability.

This product is not designed or rated for ensuring

safety of persons either directly or indirectly.

Do not use it for such purposes.

Make sure that this product is used within the rated ambient

environment conditions.

● Wiring

•Connection is made using a connector. Do not solder to the pins

(leads). The pins (leads) are soldered to the internal board of the

Sensor. Therefore, direct soldering of the pins (leads) may result in

an internal disconnection causing malfunction.

•When extending the cable, use an extension cable with conductors

having a total cross-section area of 0.3 mm2. The total cable length

must be 2 m maximum.

•To use a cable length longer than 2 m, attach a capacitor with a

capacitance of approximately 10 μF to the wires as shown below.

The distance between the terminal and the capacitor must be within

2 m. (Use a capacitor with a dielectric strength that is at least twice

the Sensor's power supply voltage.)

•Make sure the total length of the power cable connected to the

product is less than 10 m even if a capacitor is inserted.

Model Output

configuration Timing charts Output circuit

EE-SPX403N Light-ON

EE-SPX303N Dark-ON

Incident

Interrupted

OFF

Operates

Releases

Light indicator

(red)

Output

transistor

Load 1

(relay)

Load 2

Light

indicator

(red) 1.5 to

3 mA Load 1

Load 2

Main

circuit

OUT

∗

* Voltage output (when the sensor is connected to a transistor circuit)

12 to 24 VDC

Incident

Interrupted

OFF

Operates

Releases

Light indicator

(red)

Output

transistor

Load 1

(relay)

Load 2

WARNING Precautions for Correct Use

OUT

Extension cabl

A capacitance of

10 μF min.

−

12 to 24 VDC

0 V

2 m max.

EE-SPX303N/403N

(Unit: mm)

Dimensions Tolerance class IT16 applies to dimensions in this datasheet unless otherwise specified.

Sensors

Accessories (Order Separately)

*Refer to Accessories for details.

7.4

0.3 0.7

3.2

2-3.7

5.08

19.5

2.54

Four, R1.6

Indicator window

Sensing window

(0.5 × 2.2)

EE-SPX303N, EE-SPX403N

Terminal Arrangement

(1) +Vcc

(2) OUT OUTPUT

(3) −GND (0 V)

Terms and Conditions Agreement

Read and understand this catalog.

Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you

have any questions or comments.

Warranties.

(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship

for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron

disclaims all other warranties, express or implied.

(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT

NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER

ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE

PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.

Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the

Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at

Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or

replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount

equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty,

repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products

were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate

modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall

not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or

electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice,

recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above

warranty.

See http://www.omron.com/global/ or contact your Omron representative for published information.

Limitation on Liability; Etc.

OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,

LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,

WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.

Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.

Suitability of Use.

Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the

combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable

third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself

is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine,

system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product

with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.

NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE

QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,

AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE

OVERALL EQUIPMENT OR SYSTEM.

Programmable Products.

Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence

thereof.

Performance Data.

Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining

suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate

it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.

Change in Specifications.

Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our

practice to change part numbers when published ratings or features are changed, or when significant construction changes are

made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers

may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at

any time to confirm actual specifications of purchased Product.

Errors and Omissions.

Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is

assumed for clerical, typographical or proofreading errors or omissions.

2016.12

In the interest of product improvement, specifications are subject to change without notice.

OMRON Corporation

Industrial Automation Company

http://www.ia.omron.com/