ScopeMeter(R) Test Tool Innovation Introducing the complete 190 Series II Technical Data New 4-channel 500 MHz 190 Series II ScopeMeter Portable Oscilloscopes--the first high-performance scopes built for harsh industrial environments Introducing the first high-performance portable oscilloscopes with 2 or 4 independently insulated input channels, an IP51 dust- and dripwater proof rating and a CAT III 1000 V/CAT IV 600 V safety rating. Choose from 500 MHz, 200 MHz, 100 MHz or 60 MHz bandwidth models. Now plant maintenance engineers can take a 2- or 4-channel scope into the harsh world of industrial electronics. 190 Series II--a new generation of Fluke ScopeMeter Oscilloscopes QU AL RT IF 90 01 EM ST ANAGEMENT S YM Y IT CE The 190 Series II include these capabilities: * Up to four independent floating isolated inputs, up to 1000 V * Up to 5 GS/s real time sampling (depending on model and channels used) * Deep memory: 10,000 points per trace waveform capture (scope mode) * CAT III 1000 V/CAT IV 600 V safety rated instrument for industrial environments * Up to seven hours of battery operation using BP291 * Isolated USB host port for direct data storage to a USB memory device; USB device port for easy PC communication * Easy access battery door for quick battery swaps in the field * Compact and only 2.2 kg (4.8 lb) * Security slot: lock down oscilloscope with Kensington(R) lock while unattended * IP51 rating, dust- and drip-proof * Connect-and-ViewTM triggering for intelligent, automatic triggering on fast, slow and even complex signals * Frequency spectrum using FFT-analysis * Automatic capture and REPLAY of 100 screens * ScopeRecordTM Roll mode gives 30,000 points per input channel for low frequency signal analysis * TrendPlotTM paperless recorder mode with deep memory for long-term automatic measurements * 5,000 count DMM included in the 2-channel models IE D TO MEET IS O Oscilloscope modes 190-062 190-102 190-202 190-104 190-204 190-504 Vertical deflection Number of channels Bandwidth Rise time Number of scope inputs Channel architecture 2 2 2 4 4 60 MHz 100 MHz 200 MHz 100 MHz 200 MHz 5.8 ns 3.5 ns 1.7 ns 3.5 ns 1.7 ns 2 input channels plus external trigger 4 input channels All inputs fully insulated from each other and from ground Inputs may be activated in any combination AC or DC, with ground level indicator 2 mV/div to 100 V/div, plus variable attenuation User selectable: 10 kHz, or full bandwidth On each input channel, switched separately CAT III 1000 V/CAT IV 600 V rated, see General Specifications for further details 8 bit (2.1 % of reading + 0.04 x range/div) @ 5 mV/div to 100 V/div 1 M 1 % // 14 pF 2 pF 4 500 MHz 0.7 ns Maximum real-time sample rate (sampled simultaneously) 625 MS/s for each channel 5 GS/s (single channel) or 1.25GS/s per channel Record length Time base range Up to 10,000 samples per channel 10 ns/div 5 ns/div 2 ns/div 5 ns/div 2 ns/div 1 ns/div to 4 s/div to 4 s/div to 4 s/div to 4 s/div to 4 s/div to 4 s/div Time base in a 1-2-4-sequence Slower time/division settings using ScopeRecordTM Roll mode (see `Recorder mode') 10,000 samples per channel in scope mode 30,000 points per channel in ScopeRecordTM Roll mode (see `Recorder mode') (0.01 % of reading + 1 pixel) 8 ns peak detect on each channel (using real time sampling and data compression, at any timebase setting) Input coupling Input sensitivity Bandwidth limiter Normal/invert/variable Input voltage Vertical resolution Accuracy Input impedance Horizontal Maximum record length Timing accuracy Glitch capture 1.25 GS/s for each channel 2.5 GS/s (2ch) 1.25 GS/s for for each channel each channel 2.5 GS/s (2ch) 1.25 GS/s (4ch) Display and acquisition Display Display modes Visible screen width Digital persistence modes Waveform mathematics Acquisition modes 153 mm (6 in) full-color LCD with LED backlight Any combination of channels; average on/off; replay 12 divisions horizontally in scope mode off/short/medium/long/infinite and envelope mode One mathematical operation on any 2 input channels: add/subtract/multiply; X-Y-mode Frequency Spectrum using FFT analysis Normal, Averaged, Auto, Single Shot, ScopeRecordTM roll, glitch capture, waveform compare with automatic "Pass/Fail testing"; Replay Trigger and delay Source Modes Connect-and-ViewTM Video triggering (on ch. A) High-res, non-interlaced video Pulse width triggering (on channel A) Time delay Dual slope triggering N-cycle triggering 2 Fluke Corporation Input A, B or External (via meter input) Input A, B, C or D Automatic Connect-and-ViewTM, free run, single shot, edge, delay, dual slope, video, video line, selectable pulsewidth (channel A only), N-cycle Advanced automatic triggering that recognizes signal patterns, automatically sets up and continuously adjusts triggering, time base and amplitude. Automatically displays stable waveforms of complex and dynamic signals like motor drive and control signals. Can be switched off if preferred. NTSC, PAL, PAL+, SECAM; Includes field 1, field 2 and line select Non-interlaced video with line-select, for line frequencies in the range 14 kHz up to 65 kHz Pulse width qualified by time Allows for triggering <t, >t, =t, t, where t is selectable in minimum steps of 0.01 div or 50 ns 1 full screen of pre-trigger view or up to 100 screens (=1,200 divisions) of post-trigger delay Triggers on both rising and falling edges alike Triggers on N-th occurrence of a trigger event; N to be set in the range 2 to 99 ScopeMeter 190 Series II Automatic capture of 100 screens When in oscilloscope mode, the instrument ALWAYS memorizes the last 100 screens--no specific user setup required. When an anomaly is seen, the REPLAY button can be pressed to review the full sequence of screen events over and over. Instrument can be set up for triggering on glitches or intermittent anomalies and will operate in "baby-sit" mode capturing 100 specified events. Replay Manual or continuous replay. Displays the captured 100 screens as a "live" animation, or under manual control. Each screen has date and time-stamp. Replay storage Two sets of 100 screens each can be saved internally for later recall and analysis. Direct storage of additional sets on external flash memory drive through USB host port. FFT--frequency spectrum analysis Shows frequency content of oscilloscope waveform using Fast Fourier Transform Window Automatic, Hamming, Hanning or None Automatic window Digitally re-samples acquired waveform to get optimum frequency resolution in FFT resultant Vertical scale Linear/Logarithmic (in volts or amps) Frequency axis Frequency range automatically set as a function of timebase range of oscilloscope Waveform compare and pass/fail testing Waveform Compare Pass/Fail Testing Provides storage and display of a reference waveform for visual comparison with newly acquired waveforms. Reference is derived from an acquired waveform and can be modified in the oscilloscope. In waveform compare mode, the oscilloscope can be set up to store only matching ("Pass") or only non-matching ("Fail") acquired waveforms in the replay memory bank for further analysis. Automatic scope measurements V dc, V ac rms, V ac+dc, Vpeak max, Vpeak min, Vpeak to peak, A ac, A dc, A ac+dc, frequency (in Hz), rise time (using cursors), fall time (using cursors), Power Factor (PF), Watts, VA, VA reactive, phase (between any 2 inputs), pulse width (pos./neg.), duty cycle (pos./neg.), temperature C, temperature F (not for Japan), dBV, dBm into 50 I and 600 I, VPWM ac and VPWM(ac+dc) for measurement on pulse width modulated motor drives and frequency inverters, V/Hz ration (190-xx2 only) Advanced power and motor drive V/Hz ratio, Power Factor (PF), Watts, VA, VA reactive, VPWMac and VPWM (ac+dc) for measurement on functions pulsewidth modulated motordrives and frequency inverters Advanced functions mA*s (current-over-time, between cursors) V*s (voltage over time, between cursors) W*s (energy, between cursors) Cursor measurements Source Dual horizontal lines Dual vertical lines Single vertical line ZOOM On any input waveform or on mathematical resultant waveform (excl. X-Y-mode) Voltage at cursor 1 and at cursor 2, voltage between cursors Time between cursors, 1/T between cursors (in Hz), voltage between markers, risetime with markers, falltime with markers; Vrms between cursors, Watts between cursors Min-Max and Average voltage at cursor position; frequency and rms-value of individual frequency component in the FFT Resultant Ranges from full record overview to zoom in up to sample level, at any record length ScopeMeter 190 Series II Fluke Corporation 3 Meter modes 190-062 190-102 190-202 190-104 190-204 Meter inputs Via 4 mm banana inputs, fully isolated from scope inputs and scope ground Via BNC scope inputs Number of readings Maximum resolution Input impedance Advanced meter functions One at a time Up to 4 simultaneously 5,000 counts 999 counts 1 M 1 % // 14 pF 1.5pF 1 M 1 % // 15 pF 2 pF Auto/manual ranging, relative measurements (Zero reference), TrendPlotTM recording The specified accuracy is valid over the temperature range 18 C to 28 C Add 10 % of specified accuracy for each degree C below 18 C or above 28 C Voltage V dc accuracy V ac true rms accuracy 15 Hz to 60 Hz: 60 Hz to 1 kHz: 60 Hz to 20 kHz: V ac+dc true rms accuracy 15 Hz to 60 Hz: 60 Hz to 1 kHz: 60 Hz to 20 kHz: Voltmeter ranges (0.5 % + 5 counts) (1.5 % + 5 counts) (1 % + 10 counts) (2.5 % + 15 counts) (1.5 % + 10 counts) (2.5 % + 15 counts) (1 % + 10 counts) (2.5 % + 15 counts) (1.5 % + 10 counts) (2.5 % + 15 counts) 500 mV, 5 V, 50 V, 500 V, 1,000 V Resistance Ranges Accuracy 500 , 5 k, 50 k, 500 k, 5 M, 30 M (0.6 % + 5 counts) -- -- Other meter functions Continuity Diode test Current (A) Temperature 4 Fluke Corporation Beeper on < 50 ( 30 ) -- Up to 2.8 V -- A dc, A ac, A ac+dc using an optional current clamp or shunt Scaling factors: 0.1 mV/A, 1 mV/A to 100 V/A and 400 mV/A With optional accessories. Scale factors 1mV/C or 1mV/F ScopeMeter 190 Series II 190-504 Recorder modes 190-062 ScopeRecordTM 190-102 190-202 190-104 190-204 190-504 Roll Mode Dual or multiple input waveform storage mode, using deep memory Source and display Input A, Input B, Dual All channels sampled simultaneously Memory depth Min/max values Recording modes Stop-on-trigger Horizontal scale Zoom Memory Any combination of inputs, up to 4 channels All channels sampled simultaneously 30,000 data points, each holding min/max pair of information Min/max values are created at samples that are measured at high sample rate ensuring capture and display of glitches. Single sweep, continuous roll Single sweep, continuous roll Start-on-Trigger (through external) Start-on-Trigger (through any channel) Stop-on-Trigger (through external) Stop-on-Trigger (through any channel) ScopeRecord mode can be stopped by an individual trigger event, or by an interruption of a repetitive trigger signal, through any input channel (through External on 190-XX2 Series) Time from start, time of day Ranges from full record overview to zoom in up to sample level, at any record length Two multiple input ScopeRecord waveforms can be saved internally for later recall and analysis Direct storage on external flash memory drive through USB host port ScopeRecordTM Roll mode sample rate and recording timespan Time base range Recorded timespan Time/division in `view all' mode Glitch capture Sample rate Resolution 5 ms/div ~ 2 min/div 6 sec ~ 40 hr 0.5 s/div ~ 4 h/div 8 ns 125 MS/s 200 sec ~ 4.8 sec TrendplotTM Recording Multiple channel electronic paperless recorder. Graphically plots, displays and stores results of up to four automatic scope measurements or a DMM-reading over time. Source and display Any combination of scope measurements, made on any of the input channels, or DMM reading (2-channel instruments) Memory depth 19,200 points (sets) per measurement. Each recorded sample point contains a minimum, a maximum and an average value, plus a date- and time-stamp. Ranges Normal view: 5 s/div to 30 min/div In view-all mode: 5 min/div to 48 hr/div (overview of total record) Recorded time span Up to 22 days, with a resolution of 102 seconds Recording mode Continuous recording, starting at 5 s/div with automatic record compression Measurement speed Three automatic measurements per second or more Horizontal scale Time from start, time of day Zoom Up to 64x zoom-out for full record overview, up to 10x zoom-in for maximum detail Memory Two multiple input TrendPlot records can be saved internally for later recall and analysis Direct storage on external flash memory drive through USB host port Cursor measurements--all recorder modes Source Dual vertical lines Any waveform trace in any waveform display mode (Scope, ScopeRecord or TrendPlot) Cursors may be used to identify Min, Max or Average value of any datapoint in a record, with time between cursors, time from start or absolute time. ScopeMeter 190 Series II Fluke Corporation 5 General Specifications 190-062 190-102 190-202 190-104 190-204 190-504 Input voltage range Rated maximum floating voltage Probe input voltage VPS410 Probe input voltage VPS510 Maximum BNC input voltage Maximum voltage on meter input CAT III 1000 V/CAT IV 600 V (maximum voltage between any contact and earth-ground voltage level) CAT III 1000 V/CAT IV 600 V (Maximum voltage between 10:1 probe tip and reference lead) CAT III 300 V (Maximum voltage between 10:1 probe tip and reference lead) CAT IV 300 V (maximum voltage on BNC input directly) CAT III 1000 V/CAT IV 600 V -- (safety designed banana input connectors) Memory save and recall Memory locations (internal) 30 waveform memories plus 10 recording memories plus 9 screen copy memories 15 waveform memory locations Stores scope-trace waveform data (2 or 4 traces each) plus screen-copy plus corresponding setup Two recording memories Each may contain: * a 100 Screen Replay sequence, or * a ScopeRecord Roll-mode recording (2 or 4 traces), or * a TrendPlot recording of up to 4 measurements External data storage * On PC, using FlukeViewTM Software, or * Direct storage on external flash memory drive (maximum 2 GB) through USB host port Screencopies * On PC, using FlukeViewTM Software, or * Internally (in instrument) which can be copied on to external flash memory drive as .BMP-file, through USB host port Volatility Measurement data is initially stored in RAM, which is maintained by the main battery with a 30 seconds back-up when battery is exchanged. When storing data, this is written in non-volatile flash-ROM. Real-time clock Provides date and time stamp information for ScopeRecord, for 100 Screen Replay sequences and for TrendPlot recordings. Case Design Drip and dust proof Shock and vibration Display size Resolution Contrast and brightness Brightness Rugged, shock-proof with integrated protective holster. Handstrap and hangstrap included as standard Kensington lock supported to lock down instrument when left unattended. IP 51 according to IEC60529 Shock 30 g, vibration (sinusoidal) 3 g according to MIL-PRF-28800F Class 2 127 mm x 88 mm (153 mm/6.0 in diagonal) LCD 320 x 240 pixels User adjustable, temperature compensated 200 cd/m2 typical using power adapter, 90 cd/m2 typical using battery power Mechanical data Size Weight (including battery) 265 mm x 190 mm x 70 mm (10.5 in x 7.5 in x 2.8 in) 2.1 kg (4.6 lb) 2.2 kg (4.8 lb) Power Line power Battery power Battery type (incl.) and capacity [+opt. battery] Battery charge indicator Battery operating time (with backlight low) Battery charging time Battery power saving functions Mains adapter/battery charger BC190 included, version depending of country Re-chargeable double capacity Li-Ion battery (included). Battery swappable through easily accessible battery door at the rear of the instrument BP290: 2400 mAh BP291: 4800 mAh [BP291 (4800 mAh) optional] Battery has built-in status indicator for use with external charger, next to battery status indicator on instrument screen. Up to four hours using BP290 (included), Up to seven hours using BP291 (included) Up to eight hours using BP291 (optional) 21/2 hours using BP290; 5 hours using BP291 Five hours BP291 Auto `power down' with adjustable power down time Auto `Display off' with adjustable power down time On-screen battery power indicator Safety Compliance 6 Fluke Corporation EN61010-1-2001, Pollution Degree 2; CAN/CSA C22.2, No. 61010-1-04, with approval; UL61010B; ANSI/ISA-82.02.01 ScopeMeter 190 Series II Environmental Operating temperature Storage temperature Humidity Maximum operating altitude Maximum storage altitude Electro-MagneticCompatibility (EMC) Interfaces Probe calibration output Warranty 190-062 190-102 190-202 190-104 190-204 190-504 0 C ~ +40 C; 0 C ~ +50 C excluding battery -20 C ~ +60 C +10 C ~ +30 C: 95 % RH non-condensing +30 C ~ +40 C: 75 % RH non-condensing +40 C ~ +50 C: 45 % RH non-condensing Up to 2,000 m (6666 ft) for CAT IV 600 V/CAT III 1000 V Up to 3,000 m (10,000 ft) for CAT III 600 V/CAT II 1000 V 12 km (40,000 ft) EN 61326 (2005-12) for emission and immunity Two USB-ports provided. Ports are fully insulated from instrument's floating measurement circuitry USB-host port directly connects to external flash memory drive (up to 2 GB) for storage of waveform data, complete datasets in which data and setup information is included, instrument settings and screen copies A mini-USB-B is provided which allows for interconnection to PC for remote control and data transfer under PC-control. Dedicated probe-cal output with reference contact provided, fully insulated from any measurement input channel. Three years (parts and labor) on main instrument, one year on accessories Included accessories Battery charger/mains adapter Li-Ion battery pack Voltage probe sets (Each set includes ground lead, hook clip, ground spring and probe tip insulation sleeve) Test leads Other BC190 BP290 (2400 mAh) VPS410-x (one red, one blue) BP291 (4800 mAh) VPS410-x (one red, one grey, one blue, one green) TL175 (one red, one black) with test pins -- Li-Ion battery (BP290 or BP291, see above), Battery charger (BC190), Hangstrap, Handstrip (user selectable for left- or right hand use), Multi-language users manuals on CD-ROM, FlukeView(R) demo package (with restricted functionality), and USB interface cable for PC connectivity ScopeMeter 190 Series II Fluke Corporation 7 Ordering information Models Fluke 190-504 Color ScopeMeter, 500 MHz, 4 channels Fluke 190-504/S Color ScopeMeter, 500 MHz, 4 channels with SCC-290 kit included Fluke 190-204 Color ScopeMeter, 200 MHz, 4 channels Fluke 190-204/S Color ScopeMeter, 200 MHz, 4 channels, with SCC-290 kit included Fluke 190-104 Color ScopeMeter, 100 MHz, 4 channels Fluke 190-104/S Color ScopeMeter, 100 MHz, 4 channels, with SCC-290 kit included Fluke 190-202 Color ScopeMeter, 200 MHz, 2 channels plus DMM/Ext.input Fluke 190-202/S Color ScopeMeter, 200 MHz, 2 channels plus DMM/Ext.input, with SCC-290 kit included Fluke 190-102 Color ScopeMeter, 100 MHz, 2 channels plus DMM/Ext.input Fluke 190-102/S Color ScopeMeter, 100 MHz, 2 channels plus DMM/Ext.input, with SCC-290 kit included Fluke 190-062 Color ScopeMeter, 60 MHz, 2 channels plus DMM/Ext.input Fluke 190-062/S Color ScopeMeter, 60 MHz, 2 channels plus DMM/Ext.input, with SCC-290 kit included Accessories BC190 BP290 BP291 EBC290 HH290 VPS510-R VPS510-G VPS510-B VPS510-V VPS410-G VPS410-R VPS410-B VPS410-V VPS420-R VPS420-G VPS420-B VPS420-V SW90W C290 SCC290 TL175 TRM50 AS400 RS400 RS500 Mains adapter/battery charger Li-ion battery pack, 2400 mAh Li-ion battery pack, 4800 mAh External battery charger for BP290 and BP291 (uses BC190 mains adapter) Hanging Hook for 190 Series II instruments Electronic Voltage Probe set, 10:1, 500 MHz, one set red Electronic Voltage Probe set, 10:1, 500 MHz, one set grey Electronic Voltage Probe set, 10:1, 500 MHz, one set blue Electronic Voltage Probe set, 10:1, 500 MHz, one set green Industrial Voltage Probe set, 10:1, one set grey Industrial Voltage Probe set, 10:1, one set red Industrial Voltage Probe set, 10:1, one set blue Industrial Voltage Probe set, 10:1, one set green High working voltage ruggedized probe set, 100:1, 150 MHz (bicolored, red/black) High working voltage ruggedized probe set, 100:1, 150 MHz (bicolored, grey/black) High working voltage ruggedized probe set, 100:1, 150 MHz (bicolored blue/black) High working voltage ruggedized probe set, 100:1, 150 MHz (bicolored green/black) FlukeView ScopeMeter Software package (full version) Hard shell protective carrying case for 190 Series II FlukeView ScopeMeter Software package (full version) and C290 Carrying Case kit for 190 Series II TwistGuardTM safety designed test leads set (1 red, 1 black) BNC Feedthrough 50 terminator (set of 2 pieces, black) Probe Accessory Extension Set for VPS400-series probes Probe Accessory Replacement Set for VPS400-series probes Probe Accessory Replacement Set for VPS500-series probes Fluke. The Most Trusted Tools in the World. Fluke Corporation PO Box 9090, Everett, WA 98206 U.S.A. Fluke Europe B.V. PO Box 1186, 5602 BD Eindhoven, The Netherlands For more information call: In the U.S.A. (800) 443-5853 or Fax (425) 446-5116 In Europe/M-East/Africa +31 (0) 40 2675 200 or Fax +31 (0) 40 2675 222 In Canada (800)-36-FLUKE or Fax (905) 890-6866 From other countries +1 (425) 446-5500 or Fax +1 (425) 446-5116 Web access: http://www.fluke.com (c)2012-2014 Fluke Corporation. Specifications subject to change without notice. Printed in U.S.A. 1/2014 3801685F_EN Pub_ID: 11967-eng Rev 01 Modification of this document is not permitted without written permission from Fluke Corporation. 8 Fluke Corporation ScopeMeter 190 Series II