21cm COLOR TFT-LCD MODULE (8.4 TYPE) Toshiba Mobile Display Co., Ltd LTA084C272F (p-Si TFT) PRODUCT INFORMATION All information is subject to change without notice. Please read bottom notes. FEATURES (1) 8.4" SVGA color display with High Brightness (2) Built in Long Life CCFLs (MTBF:50,000 h). ( Conditions / Ta:25C IFL:6.0mA (rms)(continuing lighting), fFL:40kHz ) (3) Replaceable structure of lamp units. (4) Mounting compatible with LTM08C351 series. (5) Resistance type touch panel assemble(4 wire, Except controller) TENTATIVE RoHS compatible MECHANICAL SPECIFICATIONS Item Dimensional Outline (Typ.) Number of Pixels Active Area Pixel Pitch Weight (approximately) Backlight Specifications 199.5 (W) x 149.5 (H) x 13.0 (D) mm 800 (W) x 600 (H) pixels 170.4 (W) x 127.8 (H) mm 0.213 (W) x 0.213 (H) (540g) Sidelight ( 2 CCFLs ) ABSOLUTE MAXIMUM RATINGS Item Supply Voltage (VDD) (VFL) (fFL) (VIN) FL Driving Frequency Input Signal Voltage Operating Temperature Storage Temperature Storage Humidity (Max. wet bulb temp. = 39C) Min. -0.3 0 ---0.3 -20 -30 Max. 4.0 2.0 100 VDD+0.3 70 80 Unit V kV(rms) kHz V C C 10 90 %(RH) ELECTRICAL SPECIFICATION (RECOMMENDED OPERATION CONDITION) Item Supply Voltage FL Start Voltage Differential Input Voltage Common Mode Input Voltage High Level Input Voltage Low Level Input Voltage Current Consumption Min. 3.0 --1300 0.1 1.0 2.0 0 --4.0 --- (VDD) (VFL) (VSFL) (VID) (VCM) (VIH) (VIL) (IDD) *1 (IFL) *2 Power Consumption*1*2 Typ. 3.3 430 ----1.25 ----225 6.0 5.9 Max. 3.6 --1600 0.6 2.4-(VID)/2 VDD 0.8 --6.5 --- Unit V V(rms) V(rms) V V V V mA mA(rms) W Remarks IFL=6.0 mA(rms) Ta=0C REV REV IFL=6.0 mA(rms) *1 : 8 color bars pattern *2 : Excepting the efficiency FL inverter OPTICAL SPECIFICATION (Ta=25C) Item Contrast Ratio (CR) Viewing Angle (Upper+Lower) (CR 10) (Left+Right) Response Time (tON) (tOFF) Luminance (L) 3 4 Lamp Life Time (MTBF)* * Min. 250 --------250 Typ. 450 100 120 8 17 320 50,000 Max. ------------- Unit -- ms ms cd/m2 h Remarks Without T/P Without T/P Without T/P IFL=6.0mA(rms) *3 : Conditions ;Ta=25C, IFL=6.0mA(rms), continuous lighting *4 : Definitions of failure ; 1) Lcd luminance becomes half of the minimum value. 2) Lamp doesn't light normally. *The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by Toshiba Mobile Display Co., Ltd or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Toshiba Mobile Display Co., Ltd or others. *The information contained herein may be changed without prior notice. It is therefore advisable to contact Toshiba Mobile Display Co., Ltd before proceeding with the design of equipment incorporating this product. (1/12) 2009-05-25 (Ver.0.6R) LTA084C272F <Touch Panel Condition> Recommended Operating Conditions Item Supply Voltage VTP Min. --- Typ. 5.0 Max. 7.0 Unit V Z Min. 20 Typ. --- Max. --- Unit MOhm Rx 200 --- 1500 Ohm Ry 100 --- 1200 Ohm - ----- ----- 4.0 15 % msec Min. 0.05 3 Typ. ----- Max. 0.8 --- Unit N H Remarks Electrical Specifications Item Insulation Resistance Resistance #1 - #3(X) between #2 - #4(Y) Terminals Linearity Chattering Remarks DC25V Measured at connector pin(including conductor resistance). Mechanical Specifications Item Operating Starting Force Surface Hardness (2/12) Remarks Finger input 2009-05-25 (Ver.0.6R) 1+/-0.15 INSERTION INSPECTION MARK 0.45MAX 24.4 104.9 12.95 5+/-0.1 (YD) 6.3 141.1(T/P) 127.8(active area) (76.85) 10.75 149.5 Circuit Diagram 4.0Min.(Support Board) 3.0Min.(Contact) 1.3 (XL) 132.2(Bezel Opening) (XR) 76.85(T/P FPC) A 80+/-1 14.55 191.7 183.7(T/P) 3.9 7.9 7.9 12.35 14.55 (99.75) 199.5 (99.75) 80+/-10 193.6 191.6 4-5.5 4-8.5 13.0(with T/P) CN2 170.4(T/P Active Area) 170.4(LCD Active Area) 174.8(Bezel Opening) TENTATIVE DETAIL A(2:1) 3.7+/-0.3 3+/-0.05 1+/-0.15 1+/-0.05 2R0. 4 (3/12) (72.65) (XR) (YU) (XL) (YD) 12.95 127.8(T/P ACTIVE AREA) DIMENSIONAL OUTLINE (front) 0.3+/-0.05 (4.5) (YU) LTA084C272F Unit : mm Standard tolerance : 0.5 2009-05-25 (Ver.0.6R) LTA084C272F TENTATIVE Unit : mm (11) Standard tolerance : 0.5 CN1 (103.85) DIMENSIONAL OUTLINE (rear) (4/12) 2009-05-25 (Ver.0.6R) LTA084C272F Connector BLOCK DIAGRAM CCFL Backlight CCFL Backlight CN2 I/F Connector CN1 Y-Driver IC DC/DC Converter Gray Scale Manipulation Voltage Generation Circuit LCD Panel 800 x 600 pixels CN3 With Touch Panel Panel Controller X-Driver IC 800 pixels 1,1 1,2 X,1 X,2 800,1 800,2 1,Y X,Y 800,Y 1,600 X,600 800,600 600 pixels SEQUENCE OF POWER SUPPLIES AND SIGNALS 10ms (max.) 0.5ms (min.) 100ms (max.) 0.1ms (min.) 3.0V V DD 0.2V 500ms (min.) 3.0 V 40ms (max.) 0ms (min.) 0.2 V 40ms (max.) 0ms (min.) CLK+/RxIN0+/RxIN1+/RxIN2+/- VCM 250ms(min.) 3sec(min.) 0.2V |VID | 0ms(min.) VSFL FL Input Voltage VFL 10% VSFL 10% VFL Note ) When turn VDD on and turn it off, the form of voltage should be input with no ripple signal. (5/12) 2009-05-25 (Ver.0.6R) (6/12) X ,1 X ,2 X ,3 X ,4 t3 RGB Da ta ENAB NC LK 1 ,Y2 ,Y 3 ,Y4 ,Y 5 ,Y6 ,Y7 ,Y t5 (2 ) Ho r izon ta l T m i ing RGB Da ta ENAB NC LK (1 ) Ve r t ica l T m i ing X ,Y t4 t3 X ,Y t2 t1 798 ,Y 797 ,Y 800 ,Y 799 ,Y X ,598 X ,599 X ,600 t3 LTA084C272F TIMING CHART 2009-05-25 (Ver.0.6R) LTA084C272F TIMING SPECIFICATION 1) 2) 3) 4) 5) 6) Item Frame Period Symbol t1 Min. 604 x t3 600 x t3 Typ. 628 x t3 16.58 600 x t3 Max. 677 x t3 17.86 600 x t3 Unit --ms --- Vertical Display Term One Line Scanning Time Horizontal Display Term Clock Period t2 t3 t4 944 x t5 26.3 800 x t5 1056 x t5 26.4 800 x t5 1064 x t5 --800 x t5 --s --- t5 24.7 25.0 27.8 ns Remarks Note 1) Refer to "TIMING CHART" and LVDS (THC63LVDF84A) specifications by THine Electronics,Inc. Note 2) If ENAB is fixed to "H" or "L" level for certain period while NCLK is supplied, the panel displays black with some flicker. Note 3) Don't fix NCLK to "H" or "L" level while the VDD is supplied. If NCLK is fixed to "H" or "L" level for certain period while ENAB is spplied, the panel may be damaged. When It holds on, DC voltage supplies to liquid crystal materials and It may cause damage to liquid crystal materials. Note 4) Please adjust LCD operating signal timing and FL driving frequency, to optimize the display quality. There is a possibility that flicker is observed by the interference of LCD operating signal timing and FL driving condition (especially driving frequency), even if the condition satisfies above timing specifications and recommended operating conditions shown on page 1. Note 5) Do not make t1, t2 and t3 fluctuate. If t1, t2 and t3 are fluctuate, the panel displays black. Note 6) Keep constant the number of clock within one line scanning time and the number of scanning line within one flame period. (7/12) 2009-05-25 (Ver.0.6R) LTA084C272F CONNECTOR PIN ASSIGNMENT FOR INTERFACE CN1 INPUT SIGNAL Connector : 20268-020E-03F / I-PEX CO., LTD. Mating Connector : 20230-020B-F or 20230-T20-F or 20230-W20B-F / I-PEX CO.,LTD. DF19G-20S-1C(Plug), DF19-2830SCFA(Crimp contact) / HIROSE ELECTRIC CO., LTD. Terminal No. Symbol Function 1 VDD +3.3V POWER SUPPLY 2 VDD +3.3V POWER SUPPLY 3 GND*1 4 GND*1 5 RxIN0Negative LVDS differential data input (R0-R5, G0)*3 6 RxIN0+ Positive LVDS differential data input (R0-R5, G0) *3 1 7 GND* 8 RxIN1Negative LVDS differential data input (G1-G5, B0-B1) *3 9 RxIN1+ Positive LVDS differential data input (G1-G5, B0-B1) *3 1 10 GND* 11 RxIN2Negative LVDS differential data input (B2-B5, HS, VS, DE) *3 12 RxIN2+ Positive LVDS differential data input (B2-B5, HS, VS, DE) *3 1 13 GND* 14 CLKClock Signal (-) 15 CLK+ Clock Signal (+) 1 16 GND* 17 REV Display Reverse("L" level or Open;Normal, "H" l evel; Reverse) 18 GND*1 19 NC*2 Non Connection (open) 20 GND*1 *1 Please connect GND pin to ground. Don't use it as no-connect nor connection with high impedance. *2 Please connect NC pin to nothing. Don't connect it to ground nor to other signal input. *3 Refer to next page. CN2 CCFL POWER SOURCE Connector : BHR-04VS-1/JAPAN SOLDERLESS TERMINAL MFG CO., LTD. 4 Mating Connector * : SM04(4.0)B-BHS-1-TB/JAPAN SOLDERLESS TERMINAL MFG CO., LTD. Terminal No. Symbol Function 1 VFLH CCFL POWER SUPPLY (HIGH VOLTAGE) 2 VFLH CCFL POWER SUPPLY (HIGH VOLTAGE) 3 NC *2 4 VFLL CCFL POWER SUPPLY (LOW VOLTAGE) *4 Take away terminal No.3 of the mating connector. If does not take away, it may cause smoke burn of Electrical parts by high voltage. CN3 TOUCH PANEL FPC: 1.0mm pitch, Gold plating Mating connector: FC1S004HA1 / JAE Terminal No. Symbol Function 1 XR Touch Panel XR Terminal 2 YU Touch Panel YU Terminal 3 XL Touch Panel XL Terminal 4 YD Touch Panel YD Terminal (8/12) 2009-05-25 (Ver.0.6R) LTA084C272F RECOMMENDED TRANSMITTER (THC63LVDF63A, THC63LVDM63A by THine Electronics, Inc.) TO LTA084C272F INTERFACE ASSIGNMENT Case1: 6bit Transmitter THC63LVDF63A, THC63LVDM63A Input Terminal No. Symbol TA0 TA1 TA2 TA3 TA4 TA5 TA6 TB0 TB1 TB2 TB3 TB4 TB5 TB6 TC0 TC1 TC2 TC3 TC4 TC5 TC6 CLK IN Terminal 44 45 47 48 1 3 4 6 7 9 10 12 13 15 16 18 19 20 22 23 25 26 Symbol R0 R1 R2 R3 R4 R5 G0 G1 G2 G3 G4 G5 B0 B1 B2 B3 B4 B5 HSYNC VSYNC DE NCLK Input Signal (Graphics controller output signal) Function Red Pixels Display Data (LSB) Red Pixels Display Data Red Pixels Display Data Red Pixels Display Data Red Pixels Display Data Red Pixels Display Data (MSB) Green Pixels Display Data (LSB) Green Pixels Display Data Green Pixels Display Data Green Pixels Display Data Green Pixels Display Data Green Pixels Display Data (MSB) Blue Pixels Display Data (LSB) Blue Pixels Display Data Blue Pixels Display Data Blue Pixels Display Data Blue Pixels Display Data Blue Pixels Display Data (MSB) H-Sync V-Sync Compound Synchronization Signal Data Sampling Clock Note 1) Please connect NC pin to nothing. R x IN 0 R x IN 1 R x IN 2 Output Signal Symbol LTA084C272F Interface (CN1) Terminal Symbol TATA+ No.5 No.6 RxIN0RxIN0+ TBTB+ No.8 No.9 RxIN1RxIN1+ TCTC+ No.11 No.12 RxIN2RxIN2+ TCLKTCLK+ No.14 No.15 CLKCLK+ Don't connect it to ground nor to other signal input. TA 6 TA 5 TA 4 TA 3 TA 2 TA 1 TA 0 G0 R5 R4 R3 R2 R1 R0 TB 6 TB 5 TB 4 TB 3 TB 2 TB 1 TB 0 B1 B0 G5 G4 G3 G2 G1 TC 6 TC 5 TC 4 TC 3 TC 2 TC 1 TC 0 DE VSYNC HSYNC B5 B4 B3 B2 (9/12) 2009-05-25 (Ver.0.6R) LTA084C272F RECOMMENDED TRANSMITTER (THC63LVDM83D, THC63LVDM83R by THine Electronics, Inc.) TO LTA084C272F INTERFACE ASSIGNMENT Case2: 8bit Transmitter Input Terminal No. Symbol TA0 TA1 TA2 TA3 TA4 TA5 TA6 TB0 TB1 TB2 TB3 TB4 TB5 TB6 TC0 TC1 TC2 TC3 TC4 TC5 TC6 TD0 TD1 TD2 TD3 TD4 TD5 TD6 CLK IN Terminal 51 52 54 55 56 3 4 6 7 11 12 14 15 19 20 22 23 24 27 28 30 50 2 8 10 16 18 25 31 THC63LVDM83D,THC63LVDM83R Input Signal (Graphics controller output signal) Symbol Function R0 Red Pixels Display Data (LSB) R1 Red Pixels Display Data R2 Red Pixels Display Data R3 Red Pixels Display Data R4 Red Pixels Display Data R5 Red Pixels Display Data (MSB) G0 Green Pixels Display Data(LSB) G1 Green Pixels Display Data G2 Green Pixels Display Data G3 Green Pixels Display Data G4 Green Pixels Display Data G5 Green Pixels Display Data(MSB) B0 Blue Pixels Display Data (LSB) B1 Blue Pixels Display Data B2 Blue Pixels Display Data B3 Blue Pixels Display Data B4 Blue Pixels Display Data B5 Blue Pixels Display Data (MSB) HSYNC H-Sync VSYNC V-Sync DE Compound Synchronization Signal NC*1 Non Connection (open) NC*1 Non Connection (open) NC*1 Non Connection (open) NC*1 Non Connection (open) NC*1 Non Connection (open) NC*1 Non Connection (open) NC*1 Non Connection (open) NCLK Data Sampling Clock Note 1) Please connect NC pin to nothing. R x IN 0 R x IN 1 R x IN 2 R x IN 3 Output Signal Symbol LTA084C272F Interface (CN1) Terminal Symbol TATA+ No.5 No.6 RxIN0RxIN0+ TBTB+ No.8 No.9 RxIN1RxIN1+ TCTC+ No.11 No.12 RxIN2RxIN2+ No.14 No.15 CLKCLK+ TDTD+ TCLKTCLK+ Don't connect it to ground nor to other signal input. TA 6 TA 5 TA 4 TA 3 TA 2 TA 1 TA 0 G0 R5 R4 R3 R2 R1 R0 TB 6 TB 5 TB 4 TB 3 TB 2 TB 1 TB 0 B1 B0 G5 G4 G3 G2 G1 TC 6 TC 5 TC 4 TC 3 TC 2 TC 1 TC 0 DE VSYNC HSYNC B5 B4 B3 B2 TD 6 TD 5 TD 4 TD 3 TD 2 TD 1 TD 0 NC NC NC NC NC NC NC (10/12) 2009-05-25 (Ver.0.6R) LTA084C272F 256k (k=1024) COLORS COMBINATION TABLE Basic Color Display Black Blue Green Light Blue Red Purple Yellow White Black Gray Scale of Red Dark Light Red Black Gray Scale of Green Dark Light Green Black Gray Scale of Blue Dark Light Blue Black Gray Scale of White & Black Dark Light White R5 L L L L H H H H L L L R4 L L L L H H H H L L L R3 R2 L L L L L L L L H H H H H H H H L L L L L L : : R1 L L L L H H H H L L H R0 G5 G4 L L L L L L L H H L H H H L L H L L H H H H H H L L L H L L L L L H H H H L H H H H H H L H H H H H H L L L L L L L L L L L L L L L L L L : : L L L L L L L L L L L L H H H L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L H H L H H H L L L L L L L L L L L L L L L : : H H H H L H H H H H H L H H H H H H L L L L L L L L L L L L L L L L L H L L L L H L B5 B4 B3 B2 B1 B0 L L L L L L H H H H H H L L L L L L H H H H H H L L L L L L H H H H H H L L L L L L H H H H H H L L L L L L L L L L L L L L L L L L : : L L L L L L L L L L L L L L L L L L : : : : L L L L L L G3 G2 G1 G0 L L L L L L L L H H H H H H H H L L L L L L L L H H H H H H H H L L L L L L L L L L L L : : H H H L L L L L L L L L L L L L L L L L L L L L L L L L L L L L H L L L L H L L61 L62 Green L63 L0 L1 L2 L3... L60 L61 L62 L63 L0 L1 L2 L3... L60 H H L H H H H L H H H H L L L L L L L L L L L L : : L L L L L L L L L L L L L L L L H L H H H L L L H H H L H H H H H L H H H H H L L L L L L L L L H L L L H L : : H H L H H H H L H H H H H H H H H H L H H H H H L H H H H H L L L L L L (11/12) Red : : L L L L L H L L L L L L L L L L L L : : : : H H H Gray Scale Level ----------------L0 L1 L2 L3... L60 Blue L61 L62 L63 L0 L1 L2 L3... L60 L61 L62 White L63 2009-05-25 (Ver.0.6R) LTA084C272F ! FOR SAFETY LCD module is generally designed with precise parts to achieve light weighted thin mechanical dimensions. In using our Modules, make certain that you fully understand and put into practice the warnings and safety precautions detailed in Engineering Information No.EE-N001,"CAUTIONS AND INSTRUCTIONS FOR TOSHIBA LCD MODULES". Refer to individual specifications and TECHNICAL DATA sheets (hereinafter called "TD") for more detailed technical information. 1) SPECIAL PURPOSES A) Toshiba Mobile Display Co., Ltd 's Standard LCD Modules have not been customized for operation in extreme environments or for use in applications where performance failures could be life-threatening or otherwise catastrophic. B) Since Toshiba Mobile Display Co., Ltd 's Standard LCD Modules have not been designed for operation in extreme environments, they must never be used in devices that will be exposed to abnormally high levels of vibration or shock which exceed Toshiba Mobile Display Co., Ltd 's published specification limits. C) In addition, since Toshiba Mobile Display Co., Ltd Standard LCD Modules have not been designed for use in applications where performance failures could be life-threatening or catastrophic, they must never be installed in aircraft navigation control systems (such as, but not limited to Traffic Collision Avoidance System and Air Traffic Indicator), in military defense or weapons systems, in critical industrial process-control systems (e.g., those involved in the production of nuclear energy), or in critical medical device or patient life-support systems. 2) DISASSEMBLING OR MODIFICATION DO NOT DISASSEMBLE OR MODIFY the module. It may damage sensitive parts inside LCD module, and may cause scratches or dust on the display. Toshiba Mobile Display Co., Ltd doses not warrant the module, if customer disassembled or modified it. 3) BREAKAGE OF LCD PANEL DO NOT INGEST liquid crystal material, DO NOT INHALE this material, and DO NOT CONTACT the material with skin, if LCD panel is broken and liquid crystal material spills out. If liquid crystal material comes into mouth or eyes, rinse mouth or eyes out with water immediately. If this material contact with skin or cloths, wash it off immediately with alcohol and rinse thoroughly with water. 4) GLASS OF LCD PANEL BE CAREFUL WITH CHIPS OF GLASS that may cause injuring fingers or skin, when the glass is broken. 5) ELECTRIC SHOCK DISCONNECT POWER SUPPLY before handling LCD module. DO NOT TOUCH the parts inside LCD module and the fluorescent lamp's connector or cables in order to prevent electric shock, because high voltage is supplied to these parts from the inverter unit while power supply is turned on. 6) ABSOLUTE MAXIMUM RATINGS AND POWER PROTECTION CIRCUIT DO NOT EXCEED the absolute maximum rating values under the worst probable conditions caused by the supply voltage variation, input voltage variation, variation in parts' constants, environmental temperature, etc., otherwise LCD module may be damaged. Employ protection circuit for power supply, whenever the specification or TD specifies it. Suitable protection circuit should be applied for each system design. 7) RECOMMENDED OPERATION CONDITIONS The performance and quality of the LCD panel are warranted only when the LCD panel is used within "the recommended operation conditions". Toshiba Mobile Display Co., Ltd. never warrants the performance and quality of the LCD panel when you use the LCD panel over "the recommended operation conditions", although within "the absolute maximum rating". To use the LCD panel over "the recommended operation conditions" may have bad influence on the characteristics and reliability of the LCD panel and may shorten the life of the LCD panel. Therefore, when designing the whole set, not to be over "the recommended operation conditions", you should fully take care of supply voltage change, characteristic of connection parts, serge of input-and-output line, and surrounding temperature. 8) DISPOSAL When dispose LCD module, obey to the applicable environmental regulations. (12/12) 2009-05-25 (Ver.0.6R)