16
11.10
Metallized Polyester (PET)
SMD Film Capacitors with Box Encapsulation
Special Features Electrical Data
WIMA SMD-PET
˜ Size codes 1812, 2220, 2824,
4030, 5040 and 6054 with PET
and encapsulated
˜ Operating temperature up to 100° C
˜ Self-healing
˜ According to RoHS 2002/95/EC
Typical Applications
For general DC-applications e.g.
˜ By-pass
˜ Blocking
˜ Coupling and decoupling
˜ Timing
Construction
Dielectric:
Polyethylene-terephthalate (PET) film
Capacitor electrodes:
Vacuum-deposited
Internal construction:
Plastic film
Vacuum-deposited
electrode
Metal contact layer
(schoopage)
Terminating plate
Encapsulation:
Solvent-resistant, flame-retardant plastic
case, UL 94 V-0
Terminations:
Tinned plates.
Marking:
Box colour: Black.
Capacitance range:
0.01 mF to 6.8 mF
Rated voltages:
63 VDC, 100 VDC, 250 VDC, 400 VDC,
630 VDC, 1000 VDC
Capacitance tolerances:
±20%, ±10% (±5% available subject
to special enquiry)
Operating temperature range:
–55+ C to +100+ C
Climatic test category:
55/100/21 according to IEC
for size codes 1812 to 2824
55/100/56 according to IEC
for size codes 4030 to 6054
Insulation resistance at +20+ C:
Ur Utest C 0.33 mF 0.33 mF < C 6.8 mF
63 VDC 50 V 3.75 x 103 M¸ 1250 sec (M¸ x mF)
100 VDC 100 V (mean value: 1 x 104 M¸) (mean value: 3000 sec)
250 VDC
100 V 1 x 104 M¸ 3000 sec (M¸ x mF)
(mean value: 5 x 104 M¸) (mean value: 10 000 sec)
Measuring time: 1 min.
Dissipation factors at +20) C: tan d
at f C 0.1 mF 0.1 mF < C 1.0 mF C > 1.0 mF
1 kHz 8 x 10-3 8 x 10-3 10 x 10-3
10 kHz 15 x 10-3 15 x 10-3 –
100 kHz 30 x 10-3 – –
Maximum pulse rise time: for pulses equal to the rated voltage
Capacitance Pulse rise time V/msec
mF max. operation/test
63 VDC 100 VDC 250 VDC 400 VDC 630 VDC 1000 VDC
0.01 ... 0.022 30/300 35/350 40/400 35/350 40/400 50/500
0.033 ... 0.068 20/200 20/200 40/400 21/210 25/250 32/320
0.1 ... 0.22 10/100 10/100 12/120 14/140 17/170 –
0.33 ... 0.68 8/80 6/60 9/90 10/100 – –
1.0 ... 2.2 3.5/35 4/40 7/70 – – –
3.3 ... 6.8 3/30 3/30 – – – –
Test voltage: 1.6 Ur, 2 sec.
Voltage derating:
A voltage derating factor of 1.25 % per K
must be applied from +85) C for DC
voltages and from +75) C for AC
voltages
Reliability:
Operational life 300 000 hours
Failure rate 2 fit (0.5 x Ur and 40+ C)
Dip Solder Test/Processing
Resistance to soldering heat:
Test Tb in accordance with DIN IEC
60068-2-58/DIN EN 60384-19.
Soldering bath temperature max. 260+ C.
Soldering duration max. 5 sec.
Change in capacitance DC/C 5 %.
Soldering process:
Wave soldering and re-flow soldering
(see temperature/time graphs page 12).
Packing
Available taped and reeled in 12 mm
blister pack.
Detailed taping information and graphs
at the end of the catalogue.
For further details and graphs please
refer to Technical Information.
D
17
11.10
Continuation
General Data
D
WIMA SMD-PET
63 VDC/40 VAC* 100 VDC/63 VAC* 250 VDC/160 VAC*
Capacitance Size H Part number Size H Part number Size H Part number
code ± 0.3 code ± 0.3 code ± 0.3
0.01 mF 1812 3.0 SMDTC02100X100_ _ _ _ 1812 3.0 SMDTD02100X100_ _ _ _ 1812 4.0 SMDTF02100X200_ _ _ _
2220 3.5 SMDTC02100Y100_ _ _ _ 2220 3.5 SMDTD02100Y100_ _ _ _ 2220 3.5 SMDTF02100Y100_ _ _ _
2824 3.0 SMDTC02100T100_ _ _ _ 2824 3.0 SMDTD02100T100_ _ _ _ 2824 3.0 SMDTF02100T100_ _ _ _
0.015 „ 1812 3.0 SMDTC02150X100_ _ _ _ 1812 3.0 SMDTD02150X100_ _ _ _ 1812 4.0 SMDTF02150X200_ _ _ _
2220 3.5 SMDTC02150Y100_ _ _ _ 2220 3.5 SMDTD02150Y100_ _ _ _ 2220 3.5 SMDTF02150Y100_ _ _ _
2824 3.0 SMDTC02150T100_ _ _ _ 2824 3.0 SMDTD02150T100_ _ _ _ 2824 3.0 SMDTF02150T100_ _ _ _
0.022 „ 1812 3.0 SMDTC02220X100_ _ _ _ 1812 3.0 SMDTD02220X100_ _ _ _ 1812 4.0 SMDTF02220X200_ _ _ _
2220 3.5 SMDTC02220Y100_ _ _ _ 2220 3.5 SMDTD02220Y100_ _ _ _ 2220 3.5 SMDTF02220Y100_ _ _ _
2824 3.0 SMDTC02220T100_ _ _ _ 2824 3.0 SMDTD02220T100_ _ _ _ 2824 3.0 SMDTF02220T100_ _ _ _
0.033 „ 1812 3.0 SMDTC02330X100_ _ _ _ 1812 3.0 SMDTD02330X100_ _ _ _ 2220 3.5 SMDTF02330Y100_ _ _ _
2220 3.5 SMDTC02330Y100_ _ _ _ 2220 3.5 SMDTD02330Y100_ _ _ _ 2824 3.0 SMDTF02330T100_ _ _ _
2824 3.0 SMDTC02330T100_ _ _ _ 2824 3.0 SMDTD02330T100_ _ _ _ 4030 5.0 SMDTF02330K100_ _ _ _
0.047 „ 1812 3.0 SMDTC02470X100_ _ _ _ 1812 3.0 SMDTD02470X100_ _ _ _ 2220 3.5 SMDTF02470Y100_ _ _ _
2220 3.5 SMDTC02470Y100_ _ _ _ 2220 3.5 SMDTD02470Y100_ _ _ _ 2824 3.0 SMDTF02470T100_ _ _ _
2824 3.0 SMDTC02470T100_ _ _ _ 2824 3.0 SMDTD02470T100_ _ _ _ 4030 5.0 SMDTF02470K100_ _ _ _
0.068 „ 1812 3.0 SMDTC02680X100_ _ _ _ 1812 3.0 SMDTD02680X100_ _ _ _ 2220 3.5 SMDTF02680Y100_ _ _ _
2220 3.5 SMDTC02680Y100_ _ _ _ 2220 3.5 SMDTD02680Y100_ _ _ _ 2824 3.0 SMDTF02680T100_ _ _ _
2824 3.0 SMDTC02680T100_ _ _ _ 2824 3.0 SMDTD02680T100_ _ _ _ 4030 5.0 SMDTF02680K100_ _ _ _
0.1 mF 1812 3.0 SMDTC03100X100_ _ _ _ 1812 3.0 SMDTD03100X100_ _ _ _ 2220 3.5 SMDTF03100Y100_ _ _ _
2220 3.5 SMDTC03100Y100_ _ _ _ 2220 3.5 SMDTD03100Y100_ _ _ _ 2824 5.0 SMDTF03100T200_ _ _ _
2824 3.0 SMDTC03100T100_ _ _ _ 2824 3.0 SMDTD03100T100_ _ _ _ 4030 5.0 SMDTF03100K100_ _ _ _
0.15 „ 1812 3.0 SMDTC03150X100_ _ _ _ 1812 4.0 SMDTD03150X200_ _ _ _ 2220 4.5 SMDTF03150Y200_ _ _ _
2220 3.5 SMDTC03150Y100_ _ _ _ 2220 3.5 SMDTD03150Y100_ _ _ _ 2824 5.0 SMDTF03150T200_ _ _ _
2824 3.0 SMDTC03150T100_ _ _ _ 2824 3.0 SMDTD03150T100_ _ _ _ 4030 5.0 SMDTF03150K100_ _ _ _
0.22 „ 1812 3.0 SMDTC03220X100_ _ _ _ 1812 4.0 SMDTD03220X200_ _ _ _ 2220 4.5 SMDTF03220Y200_ _ _ _
2220 3.5 SMDTC03220Y100_ _ _ _ 2220 3.5 SMDTD03220Y100_ _ _ _ 2824 5.0 SMDTF03220T200_ _ _ _
2824 3.0 SMDTC03220T100_ _ _ _ 2824 3.0 SMDTD03220T100_ _ _ _ 4030 5.0 SMDTF03220K100_ _ _ _
0.33 „ 1812 4.0 SMDTC03330X200_ _ _ _ 2220 4.5 SMDTD03330Y200_ _ _ _ 2824 5.0 SMDTF03330T200_ _ _ _
2220 3.5 SMDTC03330Y100_ _ _ _ 2824 5.0 SMDTD03330T200_ _ _ _ 4030 5.0 SMDTF03330K100_ _ _ _
2824 3.0 SMDTC03330T100_ _ _ _ 4030 5.0 SMDTD03330K100_ _ _ _ 5040 6.0 SMDTF03330V100_ _ _ _
0.47 „ 1812 4.0 SMDTC03470X200_ _ _ _ 2220 4.5 SMDTD03470Y200_ _ _ _ 4030 5.0 SMDTF03470K100_ _ _ _
2220 3.5 SMDTC03470Y100_ _ _ _ 2824 5.0 SMDTD03470T200_ _ _ _ 5040 6.0 SMDTF03470V100_ _ _ _
2824 3.0 SMDTC03470T100_ _ _ _ 4030 5.0 SMDTD03470K100_ _ _ _
0.68 „ 2220 4.5 SMDTC03680Y200_ _ _ _ 2824 5.0 SMDTD03680T200_ _ _ _ 5040 6.0 SMDTF03680V100_ _ _ _
2824 3.0 SMDTC03680T100_ _ _ _ 4030 5.0 SMDTD03680K100_ _ _ _
4030 5.0 SMDTC03680K100_ _ _ _ 5040 6.0 SMDTD03680V100_ _ _ _
1.0 mF 2220 4.5 SMDTC04100Y200_ _ _ _ 2824 5.0 SMDTD04100T200_ _ _ _ 6054 7.0 SMDTF04100Q100_ _ _ _
2824 3.0 SMDTC04100T100_ _ _ _ 4030 5.0 SMDTD04100K100_ _ _ _
4030 5.0 SMDTC04100K100_ _ _ _ 5040 6.0 SMDTD04100V100_ _ _ _
1.5 „ 2824 5.0 SMDTC04150T200_ _ _ _ 4030 5.0 SMDTD04150K100_ _ _ _
4030 5.0 SMDTC04150K100_ _ _ _ 5040 6.0 SMDTD04150V100_ _ _ _
2.2 „ 2824 5.0 SMDTC04220T200_ _ _ _ 5040 6.0 SMDTD04220V100_ _ _ _
4030 5.0 SMDTC04220K100_ _ _ _
3.3 „ 4030 5.0 SMDTC04330K100_ _ _ _ 5040 6.0 SMDTD04330V100_ _ _ _
4.7 „ 5040 6.0 SMDTC04470V100_ _ _ _ 6054 7.0 SMDTD04470Q100_ _ _ _
6.8 „ 6054 7.0 SMDTC04680Q100_ _ _ _
* AC voltage: f =
50 Hz; 1.4 x Urms + UDC
Ur
Dims. in mm.
Rights reserved to amend design data without prior notification.
Part number completion:
Tolerance: 20 % = M
10 % = K
5 % = J
Packing: bulk = S
Lead length: none = 00
Taped version see page 126.
Continuation page 18
18
11.10
Continuation
General Data
D
WIMA SMD-PET
400 VDC/200 VAC* 630 VDC/300 VAC* 1000 VDC/400 VAC*
Capacitance Size H Part number Size H Part number Size H Part number
code ± 0.3 code ± 0.3 code ± 0.3
0.01 mF 2824 3.0 SMDTG02100T100_ _ _ _ 4030 5.0 SMDTJ02100K100_ _ _ _
4030 5.0 SMDTG02100K100_ _ _ _
0.015 „ 2824 3.0 SMDTG02150T100_ _ _ _ 4030 5.0 SMDTJ02150K100_ _ _ _ 5040 6.0 SMDTO12150V100_ _ _ _
4030 5.0 SMDTG02150K100_ _ _ _
0.022 „ 2824 3.0 SMDTG02220T100_ _ _ _ 5040 6.0 SMDTJ02220V100_ _ _ _ 5040 6.0 SMDTO12220V100_ _ _ _
4030 5.0 SMDTG02220K100_ _ _ _
0.033 „ 2824 5.0 SMDTG02330T200_ _ _ _ 5040 6.0 SMDTJ02330V100_ _ _ _ 5040 6.0 SMDTO12330V100_ _ _ _
4030 5.0 SMDTG02330K100_ _ _ _
0.047 „ 2824 5.0 SMDTG02470T200_ _ _ _ 5040 6.0 SMDTJ02470V100_ _ _ _ 6054 7.0 SMDTO12470Q100_ _ _ _
4030 5.0 SMDTG02470K100_ _ _ _
0.068 „ 4030 5.0 SMDTG02680K100_ _ _ _ 5040 6.0 SMDTJ02680V100_ _ _ _
5040 6.0 SMDTG02680V100_ _ _ _
0.1 mF 4030 5.0 SMDTG03100K100_ _ _ _ 6054 7.0 SMDTJ03100Q100_ _ _ _
5040 6.0 SMDTG03100V100_ _ _ _
0.15 „ 4030 5.0 SMDTG03150K100_ _ _ _ 6054 7.0 SMDTJ03150Q100_ _ _ _
5040 6.0 SMDTG03150V100_ _ _ _
0.22 „ 5040 6.0 SMDTG03220V100_ _ _ _ 6054 7.0 SMDTJ03220Q100_ _ _ _
0.33 „ 5040 6.0 SMDTG03330V100_ _ _ _
0.47 „ 6054 7.0 SMDTG03470Q100_ _ _ _
* AC voltage: f =
50 Hz; 1.4 x Urms + UDC
Ur
Dims. in mm.
The values of the WIMA SMD-PEN range according to
the main catalogue 2009 are still available on request.
Rights reserved to amend design data without prior notification.
Solder pad recommendation
Size L W d a b c
code ±0.3 ±0.3 min. min. max.
1812 4.8 3.3 0.5 1.2 3.5 3.5
2220 5.7 5.1 0.5 1.2 4 4.5
2824 7.2 6.1 0.5 1.2 4 6.5
4030 10.2 7.6 0.5 2.5 6 9
5040 12.7 10.2 0.7 2.5 6 11.5
6054 15.3 13.7 0.7 2.5 6 14
H
W
L
d
d
b
c
a
Bonding slit
Part number completion:
Tolerance: 20 % = M
10 % = K
5 % = J
Packing: bulk = S
Lead length: none = 00
Taped version see page 126.
12
11.10
D
Recommendation for Processing
and Application of SMD Capacitors
Layout Form
The components can generally be
positioned on the carrier material as
desired. In order to prevent soldering
shadows or ensure regular temperature
distribution, extreme concentration of
the components should be avoided. In
practice, it has proven best to keep a
minimum distance of the soldering
surfaces between two WIMA SMDs of
twice the height of the components.
Solder Pad Recommendation
H
W
L
d
d
b
c
a
Bonding slit
Size
code
L
± 0.3
W
± 0.3
d a
min.
b
min.
c
max.
1812 4.8 3.3 0.5 1.2 3.5 3.5
2220 5.7 5.1 0.5 1.2 4 4.5
2824 7.2 6.1 0.5 1.2 4 6.5
4030 10.2 7.6 0.5 2.5 6 9
5040 12.7 10.2 0.7 2.5 6 11.5
6054 15.3 13.7 0.7 2.5 6 14
The solder pad size recommendations
given for each individual series are to be
understood as minimum dimensions which
can at any time be adjusted to the layout
form.
Processing
The processing of SMD components
– assembling
– soldering
– washing
– electrical final inspection/ calibrating
must be regarded as a complete process.
The soldering of the printed circuit board,
for example, can constitute considerable
stress on all the electronic components.
The manufacturer‘s instructions on the pro-
cessing of the components are mandatory.
Due to the diverse procedures and the
varying heat requirements of the different
types of components, an exact processing
temperature for re-flow soldering processes
cannot be specified. The graph shows the
upper limits of temperature and time which
must not be exceeded when establishing
the solder profile according to your actual
requirements.
A max. temperature of T = 210° C inside
the component should not be exceeded
when processing WIMA SMD capacitors.
Soldering Process
WIMA SMD capacitors with plastic film
dielectric are generally suitable for hand-
soldering with a soldering iron where,
however, similar to automated soldering
processes, a certain duration and tempera-
ture should not be exceeded. These para-
meters are dependent on the physical size
of the components and the relevant heat
absorption involved.
The below data are to be regarded as
guideline values and should serve to avoid
damage to the dielectric caused by exces-
sive heat during the soldering process. The
soldering quality depends on the tool used
and on the skill and experience of the per-
son with the soldering iron in hand.
SMD Handsoldering
Size code Temperature ° C / ° F Time duration
1812 225 / 437 2 sec plate 1 / 5 sec off / 2 sec plate 2
2220 225 / 437 3 sec plate 1 / 5 sec off / 3 sec plate 2
2824 250 / 482 3 sec plate 1 / 5 sec off / 3 sec plate 2
4030 260 / 500 5 sec plate 1 / 5 sec off / 5 sec plate 2
5040 260 / 500 5 sec plate 1 / 5 sec off / 5 sec plate 2
6054 260 / 500 5 sec plate 1 / 5 sec off / 5 sec plate 2
Re-flow soldering
Temperature/time graph for the permissible processing temperature of the
WIMA SMD film capacitor for typical convection soldering processes.
11.10
13
D
Solder Paste
To obtain the best soldering performance
we suggest the use of following solder
paste alloy:
Lead free solder paste
Sn - Bi
Sn - Zn (Bi)
Sn - Ag - Cu
Solder paste with lead
Sn - Pb - Ag (Sn60-Pb40-A, Sn63-Pb37-A)
Washing
Basically, all plastic encapsulated compon-
ents, irrespective of the brand cannot be
considered as being hermetically sealed.
They are therefore only suitable for
industrial washing processes to a limited
extent. During the washing process,
washing agents can penetrate the interio
r
of the component by capillary action
through microcracks which might have
occurred. This is dependent on a number
of parameters e.g
- washing agents
- viscosity of the washing solvent
- temperature/time of the washing
process
- mechanical washing aids such as
ultrasonic
water pressure
rinsing and spraying pressure
The type of washing agent to be used is
largely specific to the individual user or is
often laid down by the manufacturer of the
washing equipment. The aggressiveness
of the washing agent to be used can thus
only be judged in appropriate test series
relating to each individual washing pro-
cess. By and large, the basic rule is that
the washing process should be carried out
as gently as possible.
Drying
During the washing process, aqueous
solutions can penetrate the component.
This can lead to changes of the electrical
parameters. Suitable drying measures
should ensure that no residual moisture or
traces of washing substances are left in
the component.
Initial Operation/Calibration
Due to the stress which the components
are subjected to during processing, rever-
sible parameter changes occur in almost
all electronic components. The capa-
citance recovery accuracy to be expected
with careful processing is within a scope of
DC/C 5 %.
For the initial operation of the device a
minimum storage time of
t 24 hours
is to be taken into account. With cali-
brated devices or when the application
is largely dependent on capacitance it is
advisable to prolong the storage time to
t 10 days
In this way ageing effects of the capacitor
structure can be anticipated. Parameter
changes due to processing are not to be
expected after this period of time
Humidity Protection Bags
Taped WIMA SMD capacitors are
shipped in humidity protection bags
according to JEDEC standard, level 1
(EMI/static-shielding bags conforming
to MIL-B 81705, Type 1, Class 1).
Under controlled conditions the
components can be stored two years
and more in the originally sealed bag.
Opened packing units should be
consumed instantly or resealed for specific
storage under controlled conditions.
Reliability
Taking account of the manufacturer‘s
guidelines and compatible processing,
the WIMA SMD stand out for the same
high quality and reliability as the
analogous through-hole WIMA series. The
technology of metallized film capacitors
used e.g. in WIMA SMD-PET achieves
the best values for all fields of application.
The expected value is about:
Û0 2 fit
Furthermore the production of all WIMA
components is subject to the regulations
laid down by ISO 9001:2008 as well as
the guidelines for component specifications
set out by IEC quality assessment system
(IECQ-CECC) for electronic components.
Electrical Characteristics and
Fields of Application
Basically the WIMA SMD series have the
same electrical characteristics as the ana-
logous through-hole WIMA capacitors.
Compared to ceramic or tantalum
dielectrics WIMA SMD capacitors have a
number of other outstanding qualities :
” favourable pulse rise time
” low ESR
” low dielectric absorption
” available in high voltage series
” large capacitance spectrum
” stand up to high mechanical
stress
” good long-term stability
As regards technical performance as well
as quality and reliability, the WIMA SMD
series offer the possibility to cover nearly
all applications of conventionally through-
hole film capacitors with SMD components.
Furthermore, the WIMA SMD series can
now be used for all the demanding
capacitor applications for which, in the
past, the use of through-hole components
was mandatory:
” measuring techniques
” oscillator circuits
” differentiating and integrating
circuits
” A/D or D/A transformers
” sample and hold circuits
” automotive electronics
With the WIMA SMD programme availa-
ble today, the major part of all plastic film
capacitors can be replaced by WIMA
SMD components. The field of application
ranges from standard coupling capacitors
to use in switch-mode power supplies as
filter or charging capacitors with high vol-
tage and capacitance values, as well as
in telecommunications e.g. the well-known
telephone capacitor 1mF/250VDC.
Recommendation for Processing
and Application of SMD Capacitors
(Continuation)
126
11.10
D
13 0.5
N 1.5
180/330+0
- 2
+2
- 0
W1
W max.2
P2
W0
T
F
K
D
0
D
1
P0
B0
B1
W
EG
A0A1
P
10 - 20 empty compartments 10 - 20 empty compartments min. 200 mm
Tape return Tape advance
Unwinding direction
Cover film advance
Size Code 1812 A0
± 0.1
A1B0
± 0.1
B1D0
+ 0.1
-0
D1
+ 0.1
-0
P
± 0.1
P0*
± 0.1
P2
± 0.05
E
± 0.1
F
± 0.05
G W
± 0.3
W0
± 0.2
K
± 0.1
T
± 0.1
taped
Reel
180 mm P
taped
Reel
330 mm P
bulk
Box size Code Mini Standard
4.8 x 3.3 x 3 X1 3.55 3.3 5.1 4.8 P1.5 P1.5 8 4 2 1.75 5.5 2.2 12 9.5 3.4 0.3 750 2500 1000 3000
4.8 x 3.3 x 4 X2 3.55 3.3 5.1 4.8 P1.5 P1.5 8 4 2 1.75 5.5 2.2 12 9.5 4.4 0.3 500 2000 1000 3000
Size Code 2220 A0
± 0.1
A1B0
± 0.1
B1D0
+ 0.1
-0
D1
+ 0.1
-0
P
± 0.1
P0*
± 0.1
P2
± 0.05
E
± 0.1
F
± 0.05
G W
± 0.3
W0
± 0.2
K
± 0.1
T
± 0.1
taped
Reel
180 mm P
taped
Reel
330 mm P
bulk
Box size Code Mini Standard
5.7 x 5.1 x 3.5 Y1 6.3 5.7 5.6 5.1 P1.5 P1.5 8 4 2 1.75 5.5 1.95 12 9.5 3.7 0.3 500 1800 1000 3000
5.7 x 5.1 x 4.5 Y2 6.3 5.7 5.6 5.1 P1.5 P1.5 8 4 2 1.75 5.5 1.95 12 9.5 4.7 0.3 400 1500 1000 3000
Size Code 2824 A0
± 0.1
A1B0
± 0.1
B1D0
+ 0.1
-0
D1
+ 0.1
-0
P
± 0.1
P0*
± 0.1
P2
± 0.05
E
± 0.1
F
± 0.05
G W
± 0.3
W0
± 0.2
K
± 0.1
T
± 0.1
taped
Reel
330 mm P
bulk
Box size Code Mini Standard
7.2 x 6.1 x 3 T1 6.6 6.1 7.7 7.2 P1.5 P1.5 12 4 2 1.75 5.5 0.9 12 9.5 3.4 0.3 1500 500 2000
7.2 x 6.1 x 5 T2 6.6 6.1 7.7 7.2 P1.5 P1.5 12 4 2 1.75 5.5 0.9 12 9.5 5.4 0.4 750 500 2000
Code
A0
± 0.1
A1B0
± 0.1
B1D0
+ 0.1
-0
D1
+ 0.1
-0
P
± 0.1
P0*
± 0.1
P2
± 0.05
E
± 0.1
F
± 0.05
G W
± 0.3
W0
± 0.2
K
± 0.1
T
± 0.1
taped
Reel
330 mm P
bulk
Mini Standard
Size Code 4030 K1 10.7 10.2 8.1 9.1 P1.5 P1.5 16 4 2 1.75 7.5 1.9 16 13.3 5.5 0.3 775 500 2000
Size Code 5040 V1 13.5 12.7 11 11.5 P1.5 P1.5 16 4 2 1.75 11.5 4.7 24 21.3 6.5 0.3 600 200 1000
Size Code 6054 Q1 17.0 16.5 15.6 15.0 P1.5 P1.5 20 4 2 1.75 11.5 2.95 24 21.3 7.5 0.3 450 100 500
* cumulative after 10 steps p 0.2 mm max.
Samples and pre-production needs on request or 1 Reel minimum.
All dims. in mm.
Type W2max W1± 2
0N ±1.5
1812 19 12.4 62
2220 19 12.4 62
2824 19 12.4 62
4030 22.4 16.4 60
5040 30.4 24.4 90
6054 30.4 24.4 90
Packing units
Tape reel: Tape advance and return:
Blister Tape Packaging and Packing Units
of the WIMA SMD Capacitors
W (Blister) P in mm Code
12 180 P
12 330 Q
16 330 R
24 330 T
Bulk Mini M
Bulk Standard S
Part number codes for SMD packing
125
11.10
D
A WIMA part number consists of 18 digits and is composed as follows:
Field 1 - 4: Type description
Field 5 - 6: Rated voltage
Field 7 - 10: Capacitance
Field 11 - 12: Size and PCM
Field 13 - 14: Special features (e.g. Snubber versions)
Field 15: Capacitance tolerance
Field 16: Packing
Field 17 - 18: Lead length (untaped)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
M K S 2 C 0 2 1 0 0 1 A 0 0 M S S D
MKS 2 63 VDC 0.01 mF 2.5 x 6.5 x 7.2 -20 %bulk 6 -2
WIMA Part Number System
The data on this page is not complete and serves only to explain the part number system. Part number information is listed on the
pages of the respective WIMA range.
Type description: Rated voltage: Capacitance: Size: Tolerance:
SMD-PET = SMDT 2.5 VDC = A1 22 pF = 0022 4.8 x 3.3 x 3 Size 1812 = X1 20 % = M
SMD-PPS = SMDI 4 VDC = A2 47 pF = 0047 4.8 x 3.3 x 4 Size 1812 = X2 10 % = K
FKP 02 = FKP0 14 VDC = A3 100 pF = 0100 5.7 x 5.1 x 3.5 Size 2220 = Y1 5 % = J
MKS 02 = MKS0 28 VDC = A4 150 pF = 0150 5.7 x 5.1 x 4.5 Size 2220 = Y2 2.5 % = H
FKS 2 = FKS2 40 VDC = A5 220 pF = 0220 7.2 x 6.1 x 3 Size 2824 = T1 1 % = E
FKP 2 = FKP2 5 VDC = A6 330 pF = 0330 7.2 x 6.1 x 5 Size 2824 = T2 ...
MKS 2 = MKS2 50 VDC = B0 470 pF = 0470 10.2 x 7.6 x 5 Size 4030 = K1
MKP 2 = MKP2 63 VDC = C0 680 pF = 0680 12.7 x 10.2 x 6 Size 5040 = V1
FKS 3 = FKS3 100 VDC = D0 1000 pF = 1100 15.3 x 13.7 x 7 Size 6054 = Q1 Packing:
FKP 3 = FKP3 160 VDC = E0 1500 pF = 1150 2.5 x 7 x 4.6 PCM 2.5 = 0B AMMO H16.5 340 x 340 = A
MKS 4 = MKS4 250 VDC = F0 2200 pF = 1220 3 x 7.5 x 4.6 PCM 2.5 = 0C AMMO H16.5 490 x 370 = B
MKP 4 = MKP4 400 VDC = G0 3300 pF = 1330 2.5 x 6.5 x 7.2 PCM 5 = 1A AMMO H18.5 340 x 340 = C
MKP 10 = MKP1 450 VDC = H0 4700 pF = 1470 3 x 7.5 x 7.2 PCM 5 = 1B AMMO H18.5 490 x 370 = D
FKP 4 = FKP4 600 VDC = I0 6800 pF = 1680 2.5 x 7 x 10 PCM 7.5 = 2A REEL H16.5 360 = F
FKP 1 = FKP1 630 VDC = J0 0.01 mF= 2100 3 x 8.5 x 10 PCM 7.5 = 2B REEL H16.5 500 = H
MKP-X2 = MKX2 700 VDC = K0 0.022 mF= 2220 3 x 9 x 13 PCM 10 = 3A REEL H18.5 360 = I
MKP-X2 R = MKXR 800 VDC = L0 0.047 mF= 2470 4 x 9 x 13 PCM 10 = 3C REEL H18.5 500 = J
MKP-Y2 = MKY2 850 VDC = M0 0.1 mF= 3100 5 x 11 x 18 PCM 15 = 4B ROLL H16.5 = N
MP 3-X2 = MPX2 900 VDC = N0 0.22 mF= 3220 6 x 12.5 x 18 PCM 15 = 4C ROLL H18.5 = O
MP 3-X1 = MPX1 1000 VDC = O1 0.47 mF= 3470 5 x 14 x 26.5 PCM 22.5 = 5A BLISTER W12 180 = P
MP 3-Y2 = MPY2 1100 VDC = P0 1 mF= 4100 6 x 15 x 26.5 PCM 22.5 = 5B BLISTER W12 330 = Q
MP 3R-Y2 = MPRY 1200 VDC = Q0 2.2 mF= 4220 9 x 19 x 31.5 PCM 27.5 = 6A BLISTER W16 330 = R
Snubber MKP = SNMP 1250 VDC = R0 4.7 mF= 4470 11 x21 x 31.5 PCM 27.5 = 6B BLISTER W24 330 = T
Snubber FKP = SNFP 1500 VDC = S0 10 mF= 5100 9 x 19 x 41.5 PCM 37.5 = 7A Bulk Mini = M
GTO MKP = GTOM 1600 VDC = T0 22 mF= 5220 11 x 22 x 41.5 PCM 37.5 = 7B Bulk Standard = S
DC-LINK MKP 4 = DCP4 2000 VDC = U0 47 mF= 5470 94 x 49 x 182 DCH_ = H0 Bulk Maxi = G
DC-LINK MKP C = DCPC 2500 VDC = V0 100 mF= 6100 94 x 77 x 182 DCH_ = H1 TPS Mini = X
DC-LINK HC = DCH_ 3000 VDC = W0 220 mF= 6220 ... TPS Standard = Y
SuperCap C = SCSC 4000 VDC = X0 1 F = A010 ...
SuperCap MC = SCMC 6000 VDC = Y0 2.5 F = A025
SuperCap R = SCSR 250 VAC = 0W 50 F = A500 Special features:
SuperCap MR = SCMR 275 VAC = 1W 100 F = B100 Standard = 00 Lead length (untaped)
300 VAC = 2W 110 F = B110 Version A1 = 1A 3.5 ±0.5 = C9
400 VAC = 3W 600 F = B600 Version A1.1.1 = 1B 6 -2 = SD
440 VAC = 4W 1200 F = C120 Version A1.2 = 1C 16 ±1 = P1
500 VAC = 5W ... ... ...
...
