Advance Information IDT71P71204 IDT71P71104 IDT71P71804 IDT71P71604 18Mb Pipelined DDRTMII SRAM Burst of 2 Features Description 18Mb Density (2Mx8, 2Mx9, 1Mx18, 512kx36) Common Read and Write Data Port Dual Echo Clock Output 2-Word Burst on all SRAM accesses Multiplexed Address Bus One Read or One Write request per clock cycle DDR (Double Data Rate) Data Bus - Two word bursts data per clock Depth expansion through Control Logic HSTL (1.5V) inputs that can be scaled to receive signals from 1.4V to 1.9V. Scalable output drivers Can drive HSTL, 1.8V TTL or any voltage level from 1.4V to 1.9V. Output Impedance adjustable from 35 ohms to 70 ohms 1.8V Core Voltage (VDD) 165-ball, 1.0mm pitch, 13mm x 15mm fBGA Package JTAG Interface The IDT DDRIITM Burst of two SRAMs are high-speed synchronous memories with a double-data-rate (DDR), bidirectional data port. This scheme allows maximization of the bandwidth on the data bus by passing two data items per clock cycle. The address bus operates at single data rate speeds, allowing the user to fan out addresses and ease system design while maintaining maximum performance on data transfers. The DDRII has scalable output impedance on its data output bus and echo clocks, allowing the user to tune the bus for low noise and high performance. All interfaces of the DDRII SRAM are HSTL, allowing speeds beyond SRAM devices that use any form of TTL interface. The interface can be scaled to higher voltages (up to 1.9V) to interface with 1.8V systems if necessary. The device has a VDDQ and a separate Vref, allowing the user to designate the interface operational voltage, independent of the device core voltage of 1.8V VDD. The output impedance control allows the user to adjust the drive strength to adapt to a wide range of loads and transmission lines. Clocking The DDRII SRAM has two sets of input clocks, namely the K, K clocks and the C, C clocks. In addition, the DDRII has an output "echo" clock, CQ, CQ. The K and K clocks are the primary device input clocks. The K clock is used to clock in the control signals (LD, R/W and BWx or NWx), the address, and the first word of the data burst during a write operation. Functional Block Diagram DATA REG (Note 1) K K C 18M MEMORY ARRAY (Note1) (Note4) OUTPUT SELECT (Note3) CTRL LOGIC (Note2) OUTPUT REG LD R /W BWx ADD REG SENSE AMPS SA SA 0 WRITE/READ DECODE WRITE DRIVER (Note2) CLK GEN (Note1) DQ CQ CQ SELECT OUTPUT CONTROL C 6112 drw 16 Notes 1) Represents 8 data signal lines for x8, 9 signal lines for x9, 18 signal lines for x18, and 36 signal lines for x36 2) Represents 20 address signal lines for x8 and x9, 19 address signal lines for x18, and 18 address signal lines for x36. 3) Represents 1 signal line for x9, 2 signal lines for x18, and four signal lines for x36. On x8 parts, the BW is a "nibble write" and there are 2 signal lines. 4) Represents 16 data signal lines for x8, 18 signal lines for x9, 36 signal lines for x18, and 72 signal lines for x36. MAY 2004 1 (c)2003 Integrated Device Technology, Inc. "QDR SRAMs and Quad Data Rate RAMs comprise a new family of products developed by Cypress Semiconductor, IDT, and Micron Technology, Inc. " DSC-6112/00 IDT71P71204 (2M x 8-Bit), 71P71104 (2M x 9-Bit), 71P71804 (1M x 18-Bit) 71P71604 (512K x 36-Bit) Advance Information 18 Mb DDR II SRAM Burst of 2 Commercial Temperature Range The K clock is used to clock in the control signals (BWx or NWx), and the second word of the data burst during a write operation. The K and K clocks are also used internally by the SRAM. In the event that the user disables the C and C clocks, the K and K clocks will also be used to clock the data out of the output register and generate the echo clocks. The C and C clocks may be used to clock the data out of the output register during read operations and to generate the echo clocks. C and C must be presented to the SRAM within the timing tolerances. The output data from the DDRII will be closely aligned to the C and C input, through the use of an internal DLL. When C is presented to the DDRII SRAM, the DLL will have already internally clocked the first data word to arrive at the device output simultaneously with the arrival of the C clock. The C and second data word of the burst will also correspond. Single Clock Mode The DDRII SRAM may be operated with a single clock pair. C and C may be disabled by tying both signals high, forcing the outputs and echo clocks to be controlled instead by the K and K clocks. DLL Operation The DLL in the output structure of the DDRII SRAM can be used to closely align the incoming clocks C and C with the output of the data, generating very tight tolerances between the two. The user may disable the DLL by holding Doff low. With the DLL off, the C and C (or K and K if C and C are not used) will directly clock the output register of the SRAM. With the DLL off, there will be a propagation delay from the time the clock enters the device until the data appears at the output. Echo Clock The echo clocks, CQ and CQ, are generated by the C and C clocks (or K, K if C, C are disabled). The rising edge of C generates the rising edge of CQ, and the falling edge of CQ. The rising edge of C generates the rising edge of CQ and the falling edge of CQ. This scheme improves the correlation of the rising and falling edges of the echo clock and will improve the duty cycle of the individual signals. The echo clock is very closely aligned with the data, guaranteeing that the echo clock will remain closely correlated with the data, within the tolerances designated. signals can be used to prevent writing any byte or individual nibbles, or combined to prevent writing one word of the burst. The x18 and x36 DDRll devices have the ability to address to the individual word level using the SA0 address, but the burst will continue in a linear sequence and wrap back on itself. The address will not increment to the next higher burst address location, but instead will return to it's own lower words within the burst location. Similarly when reading x18 and x36 DDRll devices, the read burst will begin at the designated address, but if the burst is started at any other position than the first word of the burst, the burst will wrap back on itself and read the first locations before completing. Output Enables The DDRII SRAM automatically enables and disables the DQ[X:0] outputs. When a valid read is in progress, and data is present at the output, the output will be enabled. If no valid data is present at the output (read not active), the output will be disabled (high impedance). The echo clocks will remain valid at all times and cannot be disabled or turned off. During power-up the DQ outputs will come up in a high impedance state. Programmable Impedance An external resistor, RQ, must be connected between the ZQ pin on the SRAM and Vss to allow the SRAM to adjust its output drive impedance. The value of RQ must be 5X the value of the intended drive impedance of the SRAM. The allowable range of RQ to guarantee impedance matching with a tolerance of +/- 10% is between 175 ohms and 350 ohms, with VDDQ = 1.5V. The output impedance is adjusted every 1024 clock cycles to correct for drifts in supply voltage and temperature. If the user wishes to drive the output impedance of the SRAM to it's lowest value, the ZQ pin may be tied to VDDQ. Read and Write Operations Read operations are initiated by holding Read/Write control input (R/W) high, the load control input (LD) low and presenting the read address to the address port during the rising edge of K, which will latch the address. The data will then be read and will appear at the device output at the designated time in correspondence with the C and C clocks. Write operations are initiated by holding the Read/Write control input (R/W) low, the load control input (LD) low and presenting the write address to the address port during the rising edge of K, which will latch the address. On the following rising edge of K, the first word of the two word burst must be present on the data input bus DQ[x:O], along with the appropriate byte write or nibble write (BW or NW) inputs. On the following rising edge of K, the second half of the data write burst will be accepted at the device input with the designated (BW or NW) inputs. DDRII devices internally store two words of the burst as a single, wide word and will retain their order in the burst. The x8 and x9 DDRII devices do not have the ability to address to the single word level or reverse the burst order; however the byte and nibble write 6.42 2 IDT71P71204 (2M x 8-Bit), 71P71104 (2M x 9-Bit), 71P71804 (1M x 18-Bit) 71P71604 (512K x 36-Bit) Advance Information 18 Mb DDR II SRAM Burst of 2 Commercial Temperature Range Pin Definitions Symbol Pin Function Description Input/Output Synchronous Data I/O s ignals. Data inputs are sampled on the rising edge of K and K during valid write operations. Data outputs are driven during a valid read operation. The outputs are aligned with the rising edge of both C and C during normal operation. When operating in a single clo ck mode (C and C tied high), the outputs are aligned with the rising edge of both K and K. When a Read operation is not initiated or LD is high (deselected) during the rising edge of K, DQ[X:O] are automatically driven to high impedance after any previous read operation in progress completes. 2M x 8 -- DQ[7:0] 2M x 9 -- DQ[8:0] 1M x 18 -- DQ[17:0] 512K x 36 -- DQ[35:0] BW0, BW1, BW2, BW3 Input Synchronous Byte Write Select 0, 1, 2, and 3 are active LOW. Sampled on the rising edge of the K and again on the rising edge of K clocks d uring write operations. Used to select which byte is writte n into the device during the current portion of the write operations. Bytes not written remain unaltered. All the byte writes are sampled on the same edge as the d ata. Deselecting a Byte Write Select will cause the corre sponding b yte of data to be ignored and not written in to the device. 2M x 9 -- BW0 controls DQ[8:0] 1M x 18 -- BW0 controls DQ[8:0] and BW1 controls DQ[17:9] 512K x 36 -- BW0 controls DQ[8:0], BW1 controls DQ[17:9], BW2 controls DQ[26:18] and BW3 controls DQ[35:27] NW0, NW1 Input Synchronous Nibble Write Select 0 and 1 are active LOW. Available only on x8 bit parts instead of Byte Write Selects. Sampled on the rising edge of the K and K clocks during write operations. Used to select which nibble is written into the device during the current portion of the write operations. Nibbles not written remain unaltered. All the nibble writes are s ampled on the same edge as the data. Dese lecting a Nibble Write Select will cause the corresponding nibble of data to be ignored and not written in to the device. SA Input Synchronous Address Inputs. Address es are sampled on the rising edge of K cloc k during active read or write operations. SA0 Input Synchronous Burst count address bit on x18 and x36 DDRll devices. This bit allows reversing the burs t order in read or write operations, or addressing to the individual word of a burst. LD Input Synchronous Load Control Logic: Sampled on the rising edge of K. If LD is low, a two word burst read or write operation will initiate as designated by the R/ W inp ut. If LD is high during the rising edge of K, operations in progress will complete, but new operations will not be initiated. R/W Input Synchronous Read or Write Control Log ic. If LD is low during the rising edge of K, the R/W indicates whether a new operation should be a read or write. If R/ W is high, a read op eration will be initiated, if R/ W is low, a write operation will be initiated. If the LD input is high during the rising e dge of K, the R/ W input will be ignored. C Input Clock Positive Output Clock Input. C is used in conjunction with C to clock out the Read data fro m the device. C and C can be used toge ther to deskew the flight times of various devices on the board back to the controller. See application example for further details. C Input Clock Negative Output Clock Input. C is used in conjunction with C to clock out the Read data from the device. C and C can be used toge ther to deskew the flight times of various devices on the board back to the controller. See application example for further details. K Input Clock Positive Input Clock. The rising ed ge of K is used to capture synchronous inputs to the device and to drive out data through DQ[X:0] when in single clock mode. All accesses are initiated on the rising edge of K. Input Clock Negative Input Clock. K is used to capture synchronous inputs being presented to the device and to drive out data through DQ[X:0] when in single clock mode. DQ[X:0] K CQ, CQ Output Clock ZQ Input Synchronous Echo clock outputs. The rising edges of these outputs are tightly matched to the synchronous data outputs and can be used as a data valid indication. These signals are free running and do not stop when the output data is three stated. Output Impedance Matching Input. This input is used to tune the device outputs to the system data bus impedance. DQ[X:0] output impedance is set to 0.2 x RQ, where RQ is a resistor connected between ZQ and ground. Alternately, this pin can be connected directly to V DDQ, which enables the minimum impedance mode. This pin cannot be connec ted directly to GND or left unconnected. 6112 tbl 02a 6.42 3 IDT71P71204 (2M x 8-Bit), 71P71104 (2M x 9-Bit), 71P71804 (1M x 18-Bit) 71P71604 (512K x 36-Bit) Advance Information 18 Mb DDR II SRAM Burst of 2 Commercial Temperature Range Pin Definitions continued Symbol Pin Function Description DLL Turn Off. When low this input will turn off the DLL inside the device. The AC timings with the DLL turned off will be different from those listed in this data sheet. There will be an increased propagation delay from the incidence of C and C to DQ, or K and K to DQ as configured. The propagation delay is not a tested parameter, but will be similar to the propagation delay of other SRAM devices in this speed grade. Doff Input TDO Output TDO pin for JTAG TCK Input TCK pin for JTAG. TDI Input TDI pin for JTAG. An internal resistor will pull TDI to V DD when the pin is unconnected. TMS Input TMS pin for JTAG. An internal resistor will pull TMS to V DD when the pin is unconnected. NC No Connect No connects inside the package. Can be tied to any voltage level VREF Input Reference Reference Voltage input. Static input used to set the reference level for HSTL inputs and outputs as well as AC measurement points. VDD Power Supply Power supply inputs to the core of the device. Should be connected to a 1.8V power supply. VSS Ground Ground for the device. Should be connected to ground of the system. VDDQ Power Supply Power supply for the outputs of the device. Should be connected to a 1.5V power supply for HSTL or scaled to the desired output voltage. 6112 tbl 02b 6.42 4 IDT71P71204 (2M x 8-Bit), 71P71104 (2M x 9-Bit), 71P71804 (1M x 18-Bit) 71P71604 (512K x 36-Bit) Advance Information 18 Mb DDR II SRAM Burst of 2 Commercial Temperature Range Pin Configuration 2M x 8 1 2 3 4 5 6 7 8 9 10 11 A CQ VSS/ SA (2) SA R/W NW1 K NC LD SA VSS/ SA (1) CQ B NC NC NC SA NC K NW0 SA NC NC DQ3 C NC NC NC VSS SA SA SA V SS NC NC NC D NC NC NC VSS VSS VSS VSS V SS NC NC NC E NC NC DQ4 V DDQ VSS VSS VSS VDDQ NC NC DQ2 F NC NC NC V DDQ VDD VSS VDD VDDQ NC NC NC G NC NC DQ5 V DDQ VDD VSS VDD VDDQ NC NC NC H Doff V REF VDDQ V DDQ VDD VSS VDD VDDQ VDDQ VREF ZQ J NC NC NC V DDQ VDD VSS VDD VDDQ NC DQ1 NC K NC NC NC V DDQ VDD VSS VDD VDDQ NC NC NC L NC DQ6 NC V DDQ VSS VSS VSS VDDQ NC NC DQ0 M NC NC NC VSS VSS VSS VSS V SS NC NC NC N NC NC NC VSS SA SA SA V SS NC NC NC P NC NC DQ7 SA SA C SA SA NC NC NC R TDO TCK SA SA SA C SA SA SA TMS TDI 6112 tbl 12 165-ball FBGA Pinout TOP VIEW NOTES: 1. A10 is reserved for the 36Mb expansion address. 2. A2 is reserved for the 72Mb expansion address. 6.42 5 IDT71P71204 (2M x 8-Bit), 71P71104 (2M x 9-Bit), 71P71804 (1M x 18-Bit) 71P71604 (512K x 36-Bit) Advance Information 18 Mb DDR II SRAM Burst of 2 Commercial Temperature Range Pin Configuration 2M x 9 1 2 3 4 5 6 7 8 9 10 11 A CQ VSS/ SA (2) SA R/W NC K NC LD SA VSS/ SA (1) CQ B NC NC NC SA NC K BW SA NC NC DQ3 C NC NC NC VSS SA SA SA VSS NC NC NC D NC NC NC VSS VSS VSS VSS VSS NC NC NC E NC NC DQ4 VDDQ VSS VSS VSS VDDQ NC NC DQ2 F NC NC NC VDDQ VDD VSS VDD VDDQ NC NC NC G NC NC DQ5 VDDQ VDD VSS VDD VDDQ NC NC NC H Doff VREF VDDQ VDDQ VDD VSS VDD VDDQ VDDQ VREF ZQ J NC NC NC VDDQ VDD VSS VDD VDDQ NC DQ1 NC K NC NC NC VDDQ VDD VSS VDD VDDQ NC NC NC L NC DQ6 NC VDDQ VSS VSS VSS VDDQ NC NC DQ0 M NC NC NC VSS VSS VSS VSS VSS NC NC NC N NC NC NC VSS SA SA SA VSS NC NC NC P NC NC DQ7 SA SA C SA SA NC NC DQ8 R TDO TCK SA SA SA C SA SA SA TMS TDI 6112 tb l 12a 165-ball FBGA Pinout TOP VIEW NOTES: 1. A10 is reserved for the 36Mb expansion address. 2. A2 is reserved for the 72Mb expansion address. 6.42 6 IDT71P71204 (2M x 8-Bit), 71P71104 (2M x 9-Bit), 71P71804 (1M x 18-Bit) 71P71604 (512K x 36-Bit) Advance Information 18 Mb DDR II SRAM Burst of 2 Commercial Temperature Range Pin Configuration 1M x 18 1 2 3 4 5 6 7 8 9 10 11 A CQ VSS/ SA (2) SA R/W BW1 K NC LD SA VSS/ SA (1) CQ B NC DQ9 NC SA NC K BW0 SA NC NC DQ8 C NC NC NC VSS SA SA0 SA V SS NC DQ7 NC D NC NC DQ10 VSS VSS VSS VSS V SS NC NC NC E NC NC DQ11 V DDQ VSS VSS VSS VDDQ NC NC DQ6 F NC DQ12 NC V DDQ VDD VSS VDD VDDQ NC NC DQ5 G NC NC DQ13 V DDQ VDD VSS VDD VDDQ NC NC NC H Doff V REF VDDQ V DDQ VDD VSS VDD VDDQ VDDQ VREF ZQ J NC NC NC V DDQ VDD VSS VDD VDDQ NC DQ4 NC K NC NC DQ14 V DDQ VDD VSS VDD VDDQ NC NC DQ3 L NC DQ15 NC V DDQ VSS VSS VSS VDDQ NC NC DQ2 M NC NC NC VSS VSS VSS VSS V SS NC DQ1 NC N NC NC DQ16 VSS SA SA SA V SS NC NC NC P NC NC DQ17 SA SA C SA SA NC NC DQ0 R TDO TCK SA SA SA C SA SA SA TMS TDI 6112 tbl 12b 165-ball FBGA Pinout TOP VIEW NOTES: 1. A10 is reserved for the 36Mb expansion address. This must be tied or driven to Vss on the 1M x 18 DDRII Burst of 2 (71P71804) devices. 2. A2 is reserved for the 72Mb expansion address. This must be tied or driven to VSS on the 1M x 18 DDRII Burst of 2 (71P71804) devices. 6.42 7 IDT71P71204 (2M x 8-Bit), 71P71104 (2M x 9-Bit), 71P71804 (1M x 18-Bit) 71P71604 (512K x 36-Bit) Advance Information 18 Mb DDR II SRAM Burst of 2 Commercial Temperature Range Pin Configuration 512K x 36 1 2 3 4 5 6 7 8 9 10 11 A CQ VSS/ SA (3) NC/ SA (1) R/W BW2 K BW1 LD SA VSS/ SA (2) CQ B NC DQ27 DQ18 SA BW3 K BW0 SA NC NC DQ8 C NC NC DQ28 VSS SA SA0 SA VSS NC DQ17 DQ7 D NC DQ29 DQ19 VSS VSS VSS VSS VSS NC NC DQ16 E NC NC DQ20 VDDQ VSS VSS VSS VDDQ NC DQ15 DQ6 F NC DQ30 DQ21 VDDQ VDD VSS VDD VDDQ NC NC DQ5 G NC DQ31 DQ22 VDDQ VDD VSS VDD VDDQ NC NC DQ14 H Doff VREF VDDQ VDDQ VDD VSS VDD VDDQ VDDQ VREF ZQ J NC NC DQ32 VDDQ VDD VSS VDD VDDQ NC DQ13 DQ4 K NC NC DQ23 VDDQ VDD VSS VDD VDDQ NC DQ12 DQ3 L NC DQ33 DQ24 VDDQ VSS VSS VSS VDDQ NC NC DQ2 M NC NC DQ34 VSS VSS VSS VSS VSS NC DQ11 DQ1 N NC DQ35 DQ25 VSS SA SA SA VSS NC NC DQ10 P NC NC DQ26 SA SA C SA SA NC DQ9 DQ0 R TDO TCK SA SA SA C SA SA SA TMS TDI 6112 tb l 12c 165-ball FBGA Pinout TOP VIEW NOTES: 1. A3 is reserved for the 36Mb expansion address. 2. A10 is reserved for the 72Mb expansion address. 3. A2 is reserved for the 144Mb expansion address 6.42 8 IDT71P71204 (2M x 8-Bit), 71P71104 (2M x 9-Bit), 71P71804 (1M x 18-Bit) 71P71604 (512K x 36-Bit) Advance Information 18 Mb DDR II SRAM Burst of 2 Commercial Temperature Range Linear Burst Sequence Table (1,2) Write Descriptions(1,2) BW0 BW1 BW2 BW3 NW0 NW1 Write Byte 0 L X X X X X Write Byte 1 X L X X X Write Byte 2 X X L X Write Byte 3 X X X Write Nibble 0 X X Write Nibble 1 X X Signal SA0 a b X 0 0 1 X X 1 1 0 L X X X X L X X X X L 6112 tbl 22 NOTE: 1. SA0 is the address presented giving the burst sequence a,b. 2. SA0 is only available on the x18 and x36-bit devices. 6112 tbl 09 NOTES: 1) All byte write (BWx) and nibble write (NWx) signals are sampled on the rising edge of K and again on K. The data that is present on the data bus in the designated byte/nibble will be latched into the input if the corresponding BWx or NWx is held low. The rising edge of K will sample the first byte/nibble of the two word burst and the rising edge of K will sample the second byte/nibble of the two word burst. 2) The availability of the BWx or NWx on designated devices is described in the pin description table. 3) The DDRII Burst of two SRAM has data forwarding. A read request that is initiated on the cycle following a write request to the same address will produce the newly written data. 6.42 9 IDT71P71204 (2M x 8-Bit), 71P71104 (2M x 9-Bit), 71P71804 (1M x 18-Bit) 71P71604 (512K x 36-Bit) Advance Information 18 Mb DDR II SRAM Burst of 2 Commercial Temperature Range Application Example SRAM #1 SRAM #4 R=250 R=250 ZQ ZQ Vt DQ SA LD R/W BW0 BW1 C C K K DQ SA R LD R/W BW0 BW1 C C K K Vt Data Bus R Address R LD R/W BWx/NWx R R R MEMORY CONTROLLER Return CLK Source CLK Return CLK Source CLK Vt Vt Vt R=50 Vt =VREF 6112 drw 20 6.42 10 Vt IDT71P71204 (2M x 8-Bit), 71P71104 (2M x 9-Bit), 71P71804 (1M x 18-Bit) 71P71604 (512K x 36-Bit) Advance Information 18 Mb DDR II SRAM Burst of 2 Commercial Temperature Range Capacitance (TA = +25C, f = 1.0MHz)(1) Absolute Maximum Ratings(1) (2) S ym bol Value Unit S up p ly Vo ltag e o n V DD with Re s p e ct to G ND -0.5 to + 2.9 V V TERM S up p ly Vo ltag e o n V DDQ with Re s p e ct to G ND -0.5 to V DD+ 0.3 V TERM Vo lta g e o n Inp ut te rm inals with re s p e c t to G ND V TERM Vo ltag e o n O utp ut and I/O te rm inals with re s p e c t to G ND. T B IA S V TERM Rating Symbol Parameter C IN Inp ut Cap acitance V C CLK Clo ck Inp ut Capacitance -0.5 to V DD + 0.3 V CO -0.5 to V DDQ + 0.3 V Te m p e rature Und e r B ias -55 to + 125 C T S TG S to rag e Te m p e rature -65 to + 150 C IOUT Co ntinuo us Curre nt into O utp uts + 20 mA NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. VDDQ must not exceed VDD during normal operation. Recommended DC Operating and Temperature Conditions Parameter Min. Typ. Max. Unit VDD Power Supply Voltage 1.7 1.8 1.9 V VDDQ I/O Supply Voltage 1.4 1.5 1.9 V VSS Ground 0 0 0 V VREF Input Reference Voltage 0.68 V DDQ/2 0.95 V TA Ambient Temperature (1) 0 +70 o _ NOTE: 1. During production testing, the case temperature equals the ambient temperature. V DD = 1.8V V DDQ = 1.5V Max. Unit 5 pF 6 pF 7 pF 6112 tb l 06 NOTE: 1. Tested at characterization and retested after any design or process change that may affect these parameters. 6 112 tb l 0 5 Symbol Outp ut Cap acitance Conditions c 6112 tbl 04 6.42 11 IDT71P71204 (2M x 8-Bit), 71P71104 (2M x 9-Bit), 71P71804 (1M x 18-Bit) 71P71604 (512K x 36-Bit) Advance Information 18 Mb DDR II SRAM Burst of 2 Commercial Temperature Range DC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range (VDD = 1.8 100mV, VDDQ = 1.4V to 1.9V) Param eter Sym bol Test Conditions Min Max Unit Inp ut Le ak ag e Curre nt IIL V DD = M ax V IN = V SS to V DD Q -10 +10 A Outp ut Le akag e Curre nt IOL Outp ut Dis ab le d -10 +10 A 333M H Z - TBD 300M H Z - TBD 250M H Z - TBD 200M Hz - TBD 167M Hz - TBD 333M H Z - TBD 300M H Z - TBD 250M H Z - TBD 200M Hz - TBD 167M Hz - TBD Op e rating Curre nt (x36,x18,x 9,x 8): DDR Stand b y Curre nt: NOP IDD IS B1 V DD = M ax , IO UT = 0mA (o utp uts o p e n), Cyc le Tim e > tKH K H M in De vice De se le cte d (in NOP state ), IO UT = 0mA (o utp uts o p e n), f=M ax, All Inp uts <0.2V o r > V DD -0.2V Note mA 1 mA 2 Outp ut Hig h Vo ltag e V O H1 RQ = 250, IOH = -15m A V DD Q /2-0.12 V DD Q /2+0.12 V 3,7 Outp ut Lo w Vo ltag e V OL1 RQ = 250, IOH = 15mA V DD Q /2-0.12 V DD Q /2+0.12 V 4,7 Outp ut Hig h Vo ltag e V O H2 IOH = -0.1m A V DD Q -0.2 V DD Q V 5 Outp ut Lo w Vo ltag e V OL2 IOL = 0.1m A V SS 0.2 V 6 NOTES: 1. Operating Current is measured at 100% bus utilization. 2. Standby Current is only after all pending read and write burst operations are completed. 3. Outputs are impedance-controlled. IOH = -(VDDQ/2)/(RQ/5) and is guaranteed by device characterization for 175 < RQ < 350. This parameter is tested at RQ = 250, which gives a nominal 50 output impedance. 4. Outputs are impedance-controlled. IOL = (VDDQ/2)/(RQ/5) and is guaranteed by device characterization for 175 < RQ < 350. This parameter is tested at RQ = 250, which gives a nominal 50 output impedance. 5. This measurement is taken to ensure that the output has the capability of pulling to the VDDQ rail, and is not intended to be used as an impedance measurement point. 6. This measurement is taken to ensure that the output has the capability of pulling to Vss , and is not intended to be used as an impedance measurement point. 7. Programmable Impedance Mode. 6.42 12 6112 tb l 10 c IDT71P71204 (2M x 8-Bit), 71P71104 (2M x 9-Bit), 71P71804 (1M x 18-Bit) 71P71604 (512K x 36-Bit) Advance Information 18 Mb DDR II SRAM Burst of 2 Commercial Temperature Range Input Electrical Characteristics Over the Operating Temperature and Supply Voltage Range (VDD = 1.8 100mV, VDDQ = 1.4V to 1.9V) PARAMETER SYMBOL MIN MAX UNIT NOTES Input High Voltage, DC VIH (DC) VREF +0.1 VDDQ +0.3 V 1,2 Input Low Voltage, DC VIL (DC) -0.3 VREF -0.1 V 1,3 Input High Voltage, AC VIH (AC) VREF +0.2 - V 4,5 Input Low Voltage, AC VIL (AC) - VREF -0.2 V 4,5 6112 tbl 10d NOTES: 1. These are DC test criteria. DC design criteria is V REF + 50mV. The AC VIH/V IL levels are defined separately for measuring timing parameters. 2. VIL (Min) DC = -0.3V, VIL (Min) AC = -0.5V (pulse width <20% tKHKH (min)) 3. VIH (Max) DC = VDDQ+0.3, VIH (Max) AC = VDD +0.5V (pulse width <20% tKHKH (min)) 4. This conditon is for AC function test only, not for AC parameter test. 5. To maintain a valid level, the transitioning edge of the input must: a) Sustain a constant slew rate from the current AC level through the target AC level, VIL(AC) or V IH(AC) b) Reach at leaset the target AC level. c) After the AC target level is reached, continue to maintain at least the target DC level, V IL(DC) or VIH (DC) Undershoot Timing Overshoot Timing 20% tKHKH (MIN) VIH VDD +0.5 VDD +0.25 VSS VDD VSS-0.25V VSS-0.5V VIL 6112 drw 22 20% tKHKH (MIN) 6112 drw 21 AC Test Conditions AC Test Load Parameter VR E F VD D Q /2 OUTPUT Device Under Test ZQ Z0 =50 RL = 50 Symbol Value Unit Core Power Supply Voltage VDD 1.7-1.9 V Output Power Supply Voltage V DDQ 1.4-1.9 V Input High/Low Level VIH/VIL 1.25/0.25 V Input Reference Level VREF VDDQ/2 V Input Rise/Fall Time TR/TF 0.3/0.3 ns VDDQ/2 V Output Timing Reference Level 6112 tbl 11a RQ = 250 VD D Q /2 NOTE: 1. Parameters are tested with RQ=250 6112 drw 04 1.25V 0.75V 0.25V 6112 drw 06 6.42 13 IDT71P71204 (2M x 8-Bit), 71P71104 (2M x 9-Bit), 71P71804 (1M x 18-Bit) 71P71604 (512K x 36-Bit) Advance Information 18 Mb DDR II SRAM Burst of 2 Commercial Temperature Range AC Electrical Characteristics (VDD = 1.8 100mV, VDDQ = 1.4V to 1.9V, TA =0 to 70C) (3,8) 333MHz Symbol Parameter 300MHz 250MHz 200MHz 167MHz Min. Max Min. Max Min. Max Min. Max Min. Max Unit 3.00 3.47 3.30 5.25 4.00 6.30 5.00 7.88 6.00 8.40 ns - 0.20 - 0.20 - 0.20 - 0.20 - 0.20 Notes Clock Parameters tKHKH Average clock cycle time (K,K,C,C) tKC var Cycle to Cycle Period Jitter (K,K,C,C) ns 1,5 tKHKL Clock High Time (K,K,C,C) 1.20 - 1.32 - 1.60 - 2.00 - 2.40 - ns 9 tKLKH Clock LOW Time (K,K,C,C) 1.20 - 1.32 - 1.60 - 2.00 - 2.40 - ns 9 tKHKH Clock to clock (KK,CC) 1.35 - 1.49 - 1.80 - 2.20 - 2.70 - ns 10 10 tKHKH Clock to clock (KK,CC) 1.35 - 1.49 - 1.80 - 2.20 - 2.70 - ns tKHCH Clock to data clock (KC,KC) 0.00 1.30 0.00 1.45 0.00 1.80 0.00 2.30 0.00 2.80 ns tKC lock DLL lock time (K, C) 1024 - 1024 - 1024 - 1024 - 1024 - cycles tKC reset K static to DLL reset 30 - 30 - 30 - 30 - 30 - ns 2 Output Parameters tCHQV C,C HIGH to output valid - 0.45 - 0.45 - 0.45 - 0.45 - 0.50 ns tCHQX C,C HIGH to output hold -0.45 - -0.45 - -0.45 - -0.45 - -0.50 - ns 3 3 tCHCQV C,C HIGH to echo clock valid - 0.45 - 0.45 - 0.45 - 0.45 - 0.50 ns 3 tCHCQX C,C HIGH to echo clock hold -0.45 - -0.45 - -0.45 - -0.45 - -0.50 - ns 3 tCQHQV CQ,CQ HIGH to output valid - 0.25 - 0.27 - 0.30 - 0.35 - 0.40 ns tCQHQX CQ,CQ HIGH to output hold -0.25 - -0.27 - -0.30 - -0.35 - -0.40 - ns tCHQZ C HIGH to output High-Z - 0.45 - 0.45 - 0.45 - 0.45 - 0.50 ns 3,4,5 tCHQX1 C HIGH to output Low-Z -0.45 - -0.45 - -0.45 - -0.45 - -0.50 - ns 3,4,5 Set-Up Times tAVKH Address valid to K,K rising edge 0.40 - 0.40 - 0.50 - 0.60 - 0.70 - ns 6 tIVKH Control inputs valid to K,K rising edge 0.40 - 0.40 - 0.50 - 0.60 - 0.70 - ns 7 tDVKH Date-in valid to K, K rising edge 0.30 - 0.30 - 0.35 - 0.40 - 0.50 - ns Hold Times tKHAX K,K rising edge to address hold 0.40 - 0.40 - 0.50 - 0.60 - 0.70 - ns 6 tKHIX K,K rising edge to control inputs hold 0.40 - 0.40 - 0.50 - 0.60 - 0.70 - ns 7 tKHDX K, K rising edge to data-in hold 0.30 - 0.30 - 0.35 - 0.40 - 0.50 - ns 6112 tbl 11 NOTES: 1. Cycle to cycle period jitter is the variance from clock rising edge to the next expected clock rising edge, as defined per JEDEC Standard No.65 (EIA/JESD65) pg.10 2. Vdd slew rate must be less than 0.1V DC per 50 ns for DLL lock retention. DLL lock time begins once Vdd and input clock are stable. 3. If C,C are tied High, K,K become the references for C,C timing parameters. 4. To avoid bus contention, at a given voltage and temperature tCHQX1 is bigger than tCHQZ. The specs as shown do not imply bus contention because tCHQX1 is a MIN parameter that is worse case at totally different test conditions (0C, 1.9V) than tCHQZ, which is a MAX parameter (worst case at 70C, 1.7V) It is not possible for two SRAMs on the same board to be at such different voltage and temperature. 5. This parameter is guaranteed by device characterization, but not production tested. 6. All address inputs must meet the specified setup and hold times for all latching clock edges. 7. Control signals are R, W,BW 0,BW 1 and (NW0,NW1, for x8) and (BW2,BW3 also for x36) 8. During production testing, the case temperature equals TA. 9. Clock High Time (tKHKL) and Clock Low Time (tKLKH) should be within 40% to 60% of the cycle time (tKHKH). 10. Clock to clock time (tKHKH) and Clock to clock time (tKHKH) should be within 45% to 55% of the cycle time (tKHKH). 6.42 14 IDT71P71204 (2M x 8-Bit), 71P71104 (2M x 9-Bit), 71P71804 (1M x 18-Bit) 71P71604 (512K x 36-Bit) Advance Information 18 Mb DDR II SRAM Burst of 2 Commercial Temperature Range Timing Waveform of Combined Read and Write Cycles NOP Read A 0 (b u rs t o f 2 ) 2 1 Read A1 (b u rs t o f 2 ) 3 NO P (N o te 1 ) 5 NOP 4 W rite A 2 (b u rs t o f 2 ) 6 W rite A 3 (b u rst o f 2 ) 7 Read A4 (b u rs t o f 2 ) 8 10 9 K tKHKL tKLKH tKH KH tKHKH K (N O T E 2 ) LD tIVKH tKHIX (N O T E 1) R/ W SA A0 A1 A2 A4 A3 tA VKH tKHAX tKHDX tKHDX tD VKH tDVKH DQ Q00 Q x1 Q 01 Q10 Q11 D 20 D 21 D 30 D31 Q40 tKH CH tC HQ V tKHC H tCQH QV tCHQZ tC HQ V tCH QX tCHQX tCH QX1 tC Q H Q X C tKH KL tKLK H tKHK H tKH K H C tC HCQ V tCHC QX CQ tC HCQ V tCH CQX CQ 6112 drw09 NOTE: 1. If a R/W is low on the next rising edge of K after a read request, the device automatically performs a NOP (No Operation.) 2. The second NOP cycle is not necessary for correct device operation; however, at high clock frequencies, it may be required to prevent the bus contention. 6.42 15 Q41 IDT71P71204 (2M x 8-Bit), 71P71104 (2M x 9-Bit), 71P71804 (1M x 18-Bit) 71P71604 (512K x 36-Bit) Advance Information 18 Mb DDR II SRAM Burst of 2 Commercial Temperature Range IEEE 1149.1 TEST ACCESS PORT AND BOUNDARY SCAN-JTAG This part contains an IEEE standard 1149.1 Compatible Test Access Port (TAP). The package pads are monitored by the Serial Scan circuitry when in test mode. This is to support connectivity testing during manufacturing and system diagnostics. In conformance with IEEE 1149.1, the SRAM contains a TAP controller, Instruction register, Bypass Register and ID register. The TAP controller has a standard 16-state machine that resets internally upon power-up; therefore, the TRST signal is not required. It is possible to use this device without utilizing the TAP. To disable the TAP controller without interfacing with normal operation of the SRAM, TCK must be tied to VSS to preclude a mid level input. TMS and TDI are designed so an undriven input will produce a response identical to the application of a logic 1, and may be left unconnected, but they may also be tied to VDD through a resistor. TDO should be left unconnected. JTAG Instruction Coding JTAG Block Diagram IR2 SR AM CO RE TDI BYP ASS R eg. TDO IR1 IR0 Instruction TDO Output Notes 0 0 0 E XTE ST B ound ary S can Reg is te r 0 0 0 IDCODE Id e ntific ation reg is te r 2 0 1 0 S AM P LE-Z B ound ary S can Reg is te r 1 0 1 1 RES E RVE D Do No t Us e 5 1 0 0 1 0 1 RES E RVE D Do No t Us e 5 1 1 0 RES E RVE D Do No t Us e 5 1 1 1 B Y PA S S B yp as s Reg is te r 3 S A MP LE/PRE LOA D B ound ary S can re giste r 4 Identification Reg. Instruction Reg . 6 112 tb l 1 3 C ontrol S ignals TMS TCK NOTE: 1. Places DQs in Hi-Z in order to sample all input data regardless of other SRAM inputs. 2. TDI is sampled as an input to the first ID register to allow for the serial shift of the external TDI data. 3. Bypass register is initialized to Vss when BYPASS instruction is invoked. The Bypass Register also holds serially loaded TDI when exiting the Shift DR states. 4. SAMPLE instruction does not place output pins in Hi-Z. 5. This instruction is reserved for future use. TAP C ontroller 6112 drw 18 TAP Controller State Diagram Test Logic Reset 1 0 Run Test Idle 1 Select DR 0 1 Select IR 1 1 Capture DR Shift DR Shift IR 0 1 Exit 1 DR Pause DR Exit 2 DR 1 Update DR 0 Exit 1 IR 0 0 1 0 1 1 1 Capture IR 0 0 1 1 0 0 Pause IR 0 0 0 1 Exit 2 IR 0 1 Update IR 0 1 6112 drw 17 6.42 16 IDT71P71204 (2M x 8-Bit), 71P71104 (2M x 9-Bit), 71P71804 (1M x 18-Bit) 71P71604 (512K x 36-Bit) Advance Information 18 Mb DDR II SRAM Burst of 2 Commercial Temperature Range Scan Register Definition Part Instrustion Register Bypass Register ID Register Boundary Scan 512K x36 3 bits 1 bit 32 bits 107 bits 1Mx18 3 bits 1 bit 32 bits 107 bits 2Mx8/x9 3 bits 1 bit 32 bits 107 bits 6112 tbl 14 Identification Register Definitions INSTRUCTION FIELD Revision Number (31:29) Device ID (28:12) IDT JEDEC ID CODE (11:1) ID Register Presence Indicator (0) ALL DEVICES 000 0 0000 0010 0101 0100 0 0000 0010 0101 0101 0 0000 0010 0101 0110 0 0000 0010 0100 0111 000 0011 0011 1 DESCRIPTION PART NUMBER Revision Number 512Kx36 1Mx18 2Mx9 2Mx8 DDRII BURST OF 2 71P71604S 71P71804S 71P71104S 71P71204S Allows unique identification of SRAM vendor. Indicates the presence of an ID register. 6112 tbl 15 6.42 17 IDT71P71204 (2M x 8-Bit), 71P71104 (2M x 9-Bit), 71P71804 (1M x 18-Bit) 71P71604 (512K x 36-Bit) Advance Information 18 Mb DDR II SRAM Burst of 2 Commercial Temperature Range Boundary Scan Exit Order (2M x 8-Bit, 2M x 9-Bit) ORDER PIN ID ORDER PIN ID ORDER PIN ID 1 6R 37 10D 73 3E 2 6P 38 9E 74 2C 3 6N 39 10C 75 1D 4 7P 40 11D 76 2E 5 7N 41 9C 77 1E 6 7R 42 9D 78 2F 7 8R 43 11B 79 3F 8 8P 44 11C 80 2G 3G 9 9R 45 9B 81 10 11P 46 10B 82 1F 11 10P 47 11A 83 1G 12 10N 48 Internal 84 1J 13 9P 14 10M 50 8B 15 11N 51 7C 49 9A 16 9M 52 6C 17 9N 53 8A 18 11L 54 7A 19 11M 55 7B 20 9L 56 6B 21 10L 57 6A 22 11K 58 5B 23 10K 59 5A 24 9J 60 4A 5C 25 9K 61 26 10J 62 4B 27 11J 63 3A 28 11H 64 2A 29 10G 65 1A 30 9G 66 2B 31 11F 67 3B 32 11G 68 33 9F 34 10F 35 36 85 2J 86 3K 87 3J 88 3L 89 2L 90 1K 91 2K 92 1M 93 1L 94 3N 95 3M 96 2N 97 3P 98 2M 99 1N 100 2P 101 1P 102 3R 103 4R 104 4P 1C 105 5P 69 1B 106 5N 70 3D 107 5R 11E 71 3C 10E 72 2D 6112 tbl 16a 6112 tbl 18a 6112 tbl 17a 6.42 18 IDT71P71204 (2M x 8-Bit), 71P71104 (2M x 9-Bit), 71P71804 (1M x 18-Bit) 71P71604 (512K x 36-Bit) Advance Information 18 Mb DDR II SRAM Burst of 2 Commercial Temperature Range Boundary Scan Exit Order (1M x 18-Bit) ORDER PIN ID ORDER PIN ID ORDER PIN ID 1 6R 37 10D 73 2C 2 6P 38 9E 74 3E 3 6N 39 10C 75 2D 4 7P 40 11D 76 2E 9C 77 1E 2F 5 7N 41 6 7R 42 9D 78 7 8R 43 11B 79 3F 8 8P 44 11C 80 1G 9 9R 45 9B 81 1F 10 11P 46 10B 82 3G 2G 11 10P 47 11A 83 12 10N 48 Internal 84 1J 13 9P 49 9A 85 2J 14 10M 50 8B 86 3K 15 11N 51 7C 87 3J 16 9M 52 6C 88 2K 17 9N 53 8A 89 1K 18 11L 54 7A 90 2L 11M 55 7B 91 3L 20 9L 56 6B 92 1M 21 10L 57 6A 93 1L 3N 3M 19 22 11K 58 5B 94 23 10K 59 5A 95 4A 96 1N 2M 24 60 9J 25 9K 61 5C 97 26 10J 62 4B 98 3P 27 11J 63 3A 99 2N 28 11H 64 1H 100 2P 29 10G 65 1A 101 1P 30 9G 66 2B 102 3R 31 11F 67 3B 103 4R 32 11G 68 1C 104 4P 33 9F 69 1B 105 5P 10F 70 3D 106 5N 35 11E 71 3C 107 5R 36 10E 72 1D 34 6112 tbl 18 6112 tbl 17 6112 tbl 16 6.42 19 IDT71P71204 (2M x 8-Bit), 71P71104 (2M x 9-Bit), 71P71804 (1M x 18-Bit) 71P71604 (512K x 36-Bit) Advance Information 18 Mb DDR II SRAM Burst of 2 Commercial Temperature Range Boundar y Scan Exit Order (512K x 36-Bit) ORDER PIN ID ORDER PIN ID ORDER PIN ID 1 6R 37 10D 73 3C 2 6P 38 10E 74 3E 3 6N 39 11C 75 1E 4 7P 40 9D 76 2E 5 7N 41 9C 77 2D 7R 42 11D 78 3F 11B 79 1F 10B 80 1G 6 7 43 8R 8 8P 44 9 9R 45 9B 81 2F 10 11P 46 10C 82 3G 2J 11 9P 47 11A 83 12 10N 48 Internal 84 1J 13 10P 49 9A 85 2G 14 11M 50 8B 86 3K 15 9N 51 7C 87 1K 16 9M 52 6C 88 2K 17 11N 53 8A 89 3J 18 11L 54 7A 90 3L 19 10L 55 7B 91 1L 20 9L 56 6B 92 1M 21 10M 57 6A 93 2L 11K 58 5B 94 3N 2M 22 23 9K 59 5A 95 24 9J 60 4A 96 1N 3M 25 10K 61 5C 97 26 11J 62 4B 98 3P 3A 99 1P 100 2P 27 63 9G 28 11H 64 1H 29 10G 65 1A 101 2N 30 10J 66 3B 102 3R 31 11F 67 1B 103 4R 32 10F 68 1C 104 4P 9F 69 2B 105 5P 11G 70 3D 106 5N 35 11E 71 2C 107 5R 36 9E 72 1D 33 34 6112 tbl 18b 6112 tbl 17b 6112 tbl 16b 6.42 20 IDT71P71204 (2M x 8-Bit), 71P71104 (2M x 9-Bit), 71P71804 (1M x 18-Bit) 71P71604 (512K x 36-Bit) Advance Information 18 Mb DDR II SRAM Burst of 2 Commercial Temperature Range JTAG DC Operating Conditions Parameter Symbol Min Typ Max Unit Output Power Supply VDDQ 1.4 - 1.9 V Power Supply Voltage VDD 1.7 1.8 1.9 V Input High Level VIH 1.3 - VDD+0.3 V Input Low Level VIL -0.3 - 0.5 V Output High Voltage (IOH = -1mA) VOH VDDQ - 0.2 - VDDQ V 1 Output Low Voltage (IOL = 1mA) VOL VSS - 0.2 V 1 NOTE: 1. The output impedance of TDO is set to 50 ohms (nominal process) and does not vary with the external resistor connected to ZQ. Note 6112 tbl 19 JTAG AC Test Conditions Parameter Symbol Min Unit Input High/Low Level VIH/V IL 1.3/0.5 V Input Rise/Fall Time TR/TF 1.0/1.0 ns VDDQ/2 V Inp ut and Output Timing Reference Level Note 1 NOTE: 1. See AC test load on page 12. 6112 tbl 20 JTAG AC Characteristics Parameter Symbol Min Max Unit TCK Cycle Time tCHCH 50 - ns TCK High Pulse Width tCHCL 20 - ns TCK Low Pulse Width tCLCH 20 - ns TMS Input Setup Time tMVCH 5 - ns TMS Input Hold Time tCHMX 5 - ns TDI Input Setup Time tDVCH 5 - ns TDI Input Hold Time tCHDX 5 - ns SRAM Input Setup Time tSVCH 5 - ns SRAM Input Hold Time tCHSX 5 - ns Clock Low to Output Valid tCLQV 0 10 ns Note 6112 tbl.21 JTAG Timing Diagram TC K tC H C L tC H C H tM V C H tC H M X tD V C H tC H D X tS V C H tC H S X tC L C H TM S TD I/ SRAM Inp u ts S RA M O u tp u ts tC L Q V TDO 61 1 2 drw 1 9 6.42 21 IDT71P71204 (2M x 8-Bit), 71P71104 (2M x 9-Bit), 71P71804 (1M x 18-Bit) 71P71604 (512K x 36-Bit) Advance Information 18 Mb DDR II SRAM Burst of 2 Commercial Temperature Range Package Diagram Outline for 165-Ball Fine Pitch Grid Array 6.42 22 IDT71P71204 (2M x 8-Bit), 71P71104 (2M x 9-Bit), 71P71804 (1M x 18-Bit) 71P71604 (512K x 36-Bit) Advance Information 18 Mb DDR II SRAM Burst of 2 Commercial Temperature Range Ordering Information IDT 71P71XXX Device Type S XXX BQ Power Speed Package BQ 333 300 250 200 167 165 Fine Pitch Ball Grid Array (fBGA) Clock Frequency in MegaHertz IDT71P71204 IDT71P71104 IDT71P71804 IDT71P71604 2M x 8 DDR II SRAM Burst of 2 2M x 9 DDR II SRAM Burst of 2 1M x 18 DDR II SRAM Burst of 2 512K x 36 DDR II SRAM Burst of 2 6112 drw 15 CORPORATE HEADQUARTERS 2975 Stender Way Santa Clara, CA 95054 for SALES: 800-345-7015 or 408-727-6116 fax: 408-492-8674 www.idt.com for Tech Support: sramhelp@idt.com 800-544-7726 "QDR SRAMs and Quad Data Rate RAMs comprise a new family of products developed by Cypress Semiconductor, IDT, and Micron Technology, Inc. " 6.42 23 IDT71P71204 (2M x 8-Bit), 71P71104 (2M x 9-Bit), 71P71804 (1M x 18 x -Bit) 71P71604 (512K x 36-Bit) Advance Information 18 Mb DDR II SRAM Burst of 2 Commercial Temperature Range Revision History REVISION 0 DATE 05/31/04 PAGES DESCRIPTION 1-23 Initial Advance Information Data Sheet Release