TSOP752..W, TSOP754..W www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES * Very low supply current * Photo detector and preamplifier in one package * Internal filter for PCM frequency * Supply voltage: 2.5 V to 5.5 V * Improved immunity against ambient light * Capable of side or top view * Low profile 2.35 mm * Insensitive to supply voltage ripple and noise * Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 DESCRIPTION DESIGN SUPPORT TOOLS The TSOP75...W series are miniaturized SMD IR receiver modules for infrared remote control systems. Two PIN diodes and a preamplifier are assembled on a leadframe, the epoxy package contains an IR filter. click logo to get started Models Available The demodulated output signal can be directly connected to a microprocessor for decoding. MECHANICAL DATA The TSOP754..W series devices are optimized to suppress almost all spurious pulses from energy saving lamps like CFLs. The AGC4 used in the TSOP754..W may suppress some data signals. The TSOP752..W series are provided primarily for compatibility with old AGC2 designs. New designs should prefer the TSOP754..W series containing the newer AGC4. Pinning: 1, 4 = GND, 2 = VS, 3 = OUT ORDERING CODE Taping: TSOP75...WTT - top view taped These components have not been qualified according to automotive specifications. TSOP75...WTR - side view taped PARTS TABLE AGC LEGACY, FOR LONG BURST REMOTE CONTROLS (AGC2) RECOMMENDED FOR LONG BURST CODES (AGC4) TSOP75230W TSOP75430W 30 kHz Carrier frequency 33 kHz TSOP75233W TSOP75433W 36 kHz TSOP75236W TSOP75436W (1)(2)(3) 38 kHz TSOP75238W TSOP75438W (4)(5) 40 kHz TSOP75240W TSOP75440W 56 kHz TSOP75256W TSOP75456W (6)(7) Package Heimdall no lens Pinning 1, 4 = GND, 2 = VS, 3 = OUT Dimensions (mm) 6.8 W x 3.0 H x 2.35 D Mounting SMD Application Best choice for Rev. 1.9, 26-Apr-2018 Remote control (1) RC-5 (2) RC-6 (3) Panasonic 1 (4) NEC (5) Sharp (6) r-step (7) Thomson RCA Document Number: 82496 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP752..W, TSOP754..W www.vishay.com Vishay Semiconductors BLOCK DIAGRAM APPLICATION CIRCUIT 2 17170-11 VS 3 Input Band pass AGC IR receiver VS OUT Demodulator C OUT 1, 4 PIN + VS C1 Circuit 30 k R1 Transmitter with TSALxxxx VO GND GND GND Control circuit R1 and C1 recommended to reduce supply ripple for VS < 2.8 V 20445-1 ABSOLUTE MAXIMUM RATINGS PARAMETER Supply voltage Supply current Output voltage Output current Junction temperature Storage temperature range Operating temperature range Power consumption TEST CONDITION SYMBOL VS IS VO IO Tj Tstg Tamb Ptot Tamb 85 C VALUE -0.3 to +6 3 -0.3 to (VS + 0.3) 5 100 -25 to +85 -25 to +85 10 UNIT V mA V mA C C C mW Note * Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified) PARAMETER Supply voltage TEST CONDITION Ev = 0, VS = 3.3 V Ev = 40 klx, sunlight Ev = 0, test signal see Fig. 1, IR diode TSAL6200, IF = 200 mA IOSL = 0.5 mA, Ee = 0.7 mW/m2, test signal see Fig. 1 Pulse width tolerance: tpi - 5/fo < tpo < tpi + 6/fo, test signal see Fig. 1 tpi - 5/fo < tpo < tpi + 6/fo, test signal see Fig. 1 Angle of half transmission distance Supply current Transmission distance Output voltage low Minimum irradiance Maximum irradiance Directivity SYMBOL VS ISD ISH MIN. 2.5 0.27 - TYP. 0.35 0.45 MAX. 5.5 0.45 - UNIT V mA mA d - 30 - m VOSL - - 100 mV Ee min. - 0.25 0.5 mW/m2 Ee max. 1/2 30 - 75 - W/m2 deg TYPICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified) Optical Test Signal 1.0 (IR diode TSAL6200, IF = 0.4 A, 30 pulses, f = f0, t = 10 ms) tpo - Output Pulse Width (ms) Ee t tpi * T 10/f0 is recommended for optimal function * tpi VO Output Signal 1) VOH 2) 16110 7/f0 < td < 15/f0 tpi - 5/f0 < tpo < tpi + 6/f0 Output Pulse Width 0.9 0.8 Input Burst Length 0.7 0.6 0.5 0.4 0.3 = 950 nm, Optical Test Signal, Fig.1 0.2 0.1 0 0.1 VOL td 1) tpo 2) t 21583 Fig. 1 - Output Active Low Rev. 1.9, 26-Apr-2018 1 10 102 103 104 105 Ee - Irradiance (mW/m) Fig. 2 - Pulse Length and Sensitivity in Dark Ambient 2 Document Number: 82496 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP752..W, TSOP754..W www.vishay.com Optical Test Signal 600 s Ee min. - Threshold Irradiance (mW/m) Ee Vishay Semiconductors t 600 s t = 60 ms 94 8134 Output Signal, (see Fig. 4) VO VOH VOL t on 4 Correlation with Ambient Light Sources: 3.5 10 W/m = 1.4 kLx (Std. illum. A, T = 2855 K) 10 W/m = 8.2 kLx (Daylight, T = 5900 K) 3 2.5 2 1 0.5 0 0.01 t t off 0.6 Toff 0.4 0.3 = 950 nm, Optical Test Signal, Fig. 3 0.1 0 0.1 21584 1 10 102 103 104 105 Ee - Irradiance (mW/m) 100 2.5 f = f0 f = 30 kHz f = 10 kHz f = 100 Hz 2.0 1.5 1.0 0.5 0 1 10 100 1000 VS RMS - AC Voltage on DC Supply Voltage (mV) Fig. 4 - Output Pulse Diagram Fig. 7 - Sensitivity vs. Supply Voltage Disturbances 1.2 1.0 0.9 1.0 Max. Envelope Duty Cycle Ee min./Ee - Relative Responsivity 10 3.0 Ee min. - Threshold Irradiance (mW/m2) Ton, Toff - Output Pulse Width (ms) Ton 0.2 1 Fig. 6 - Sensitivity in Bright Ambient 0.8 0.5 0.1 Ee - Ambient DC Irradiance (W/m) 21585 Fig. 3 - Output Function 0.7 Wavelength of Ambient Illumination: = 950 nm 1.5 0.8 0.6 0.4 f = f0 5 % f(3 dB) = f0/10 0.2 0.8 0.7 0.6 0.5 TSOP752..W 0.4 0.3 TSOP754..W 0.2 0.1 0.0 f = 38 kHz, Ee = 2 mW/m 0 0.7 16925 0.9 1.1 0 1.3 21588 f/f0 - Relative Frequency Fig. 5 - Frequency Dependence of Responsivity Rev. 1.9, 26-Apr-2018 20 40 60 80 100 120 Burst Length (number of cycles/burst) Fig. 8 - Max. Envelope Duty Cycle vs. Burst Length 3 Document Number: 82496 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP752..W, TSOP754..W Vishay Semiconductors 0.6 0 d rel - Relative Transmission Distance Ee min. - Threshold Irradiance (mW/m2) www.vishay.com 0.5 0.4 0.3 0.2 0.1 0 -30 -10 10 30 50 70 40 0.9 50 0.8 60 70 0.7 80 0.6 21580 0.4 0.2 0 Fig. 12 - Vertical Directivity 0.60 1.0 0.9 Ee min. - Sensitivity (mW/m2) S () rel - Relative Spectral Sensitivity 30 1.0 Fig. 9 - Sensitivity vs. Ambient Temperature 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 750 0.50 0.40 0.30 0.20 0.10 0.00 800 850 900 950 1000 1050 1100 1150 1 - Wavelength (nm) 21425 0 10 2 3 4 5 VS - Supply Voltage (V) Fig. 10 - Relative Spectral Sensitivity vs. Wavelength d rel - Relative Transmission Distance 20 90 Tamb - Ambient Temperature (C) 21581 10 20 Fig. 13 - Sensitivity vs. Supply Voltage 30 40 1.0 50 0.9 60 0.8 70 80 0.7 0.6 0.4 0.2 0 Fig. 11 - Horizontal Directivity Rev. 1.9, 26-Apr-2018 4 Document Number: 82496 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP752..W, TSOP754..W www.vishay.com Vishay Semiconductors SUITABLE DATA FORMAT Axis Title This series is designed to suppress spurious output pulses due to noise or disturbance signals. The devices can distinguish data signals from noise due to differences in frequency, burst length, and envelope duty cycle. The data signal should be close to the device's band-pass center frequency (e.g. 38 kHz) and fulfill the conditions in the table below. 10000 7 6 When a data signal is applied to the product in the presence of a disturbance, the sensitivity of the receiver is automatically reduced by the AGC to insure that no spurious pulses are present at the receiver's output. 1000 1st line 2nd line 2nd line IR Signal Amplitude 5 4 3 100 2 1 Some examples which are suppressed are: 10 0 * DC light (e.g. from tungsten bulbs sunlight) 0 5 15 20 Time (ms) 16920 * Continuous signals at any frequency 10 Fig. 14 - IR Disturbance from Fluorescent Lamp With Low Modulation * Strongly or weakly modulated patterns from fluorescent lamps with electronic ballasts (see Fig. 14 or Fig. 15) Axis Title 10000 40 1000 0 1st line 2nd line 2nd line IR Signal Amplitude 20 -20 100 -40 10 -60 0 5 10 15 20 Time (ms) 16921 Fig. 15 - IR Disturbance from Fluorescent Lamp With High Modulation TSOP752..W TSOP754..W Minimum burst length 10 cycles/burst 10 cycles/burst After each burst of length a minimum gap time is required of 10 to 70 cycles 10 cycles 10 to 35 cycles 10 cycles For bursts greater than a minimum gap time in the data stream is needed of 70 cycles > 4 x burst length 35 cycles > 10 x burst length Maximum number of continuous short bursts/second 1800 1500 NEC code Yes Preferred RC5 / RC6 code Yes Preferred Thomson 56 kHz code Yes Preferred Sharp code Yes Preferred Mild disturbance patterns are suppressed (example: signal pattern of Fig. 14) Complex and critical disturbance patterns are suppressed (example: signal pattern of Fig. 15 or highly dimmed LCDs) Suppression of interference from fluorescent lamps Notes * For data formats with short bursts please see the datasheet for TSOP753..W * For Sony 12, 15, and 20 bit IR codes please see the datasheet of TSOP75S40FW Rev. 1.9, 26-Apr-2018 5 Document Number: 82496 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP752..W, TSOP754..W www.vishay.com Vishay Semiconductors PACKAGE DIMENSIONS in millimeters 6.8 6.6 0.1 Center of sensitive area (3.25) Mold residue 2.35 (1.8) 1.2 0.2 3 0.8 Mold residue (0.635) (1) 1.27 (3 x) 0.5 0.1 (4 x) technical drawings according to DIN specifications 3 x 1.27 = 3.81 Marking area 2.05 Not indicated tolerances 0.15 (1.5) Tool separation line (2.2) Proposed pad layout from component side (for reference only) 3 x 1.27 = 3.81 Pick and place area 1.8 1.27 Drawing-No.: 6.550-5300.01-4 Issue: 4; 13.09.11 0.8 22609 ASSEMBLY INSTRUCTIONS Reflow Soldering Manual Soldering * Reflow soldering must be done within 72 h while stored under a max. temperature of 30 C, 60 % RH after opening the dry pack envelope * Use a soldering iron of 25 W or less. Adjust the temperature of the soldering iron below 300 C * Set the furnace temperatures for pre-heating and heating in accordance with the reflow temperature profile as shown in the diagram. Exercise extreme care to keep the maximum temperature below 260 C. The temperature shown in the profile means the temperature at the device surface. Since there is a temperature difference between the component and the circuit board, it should be verified that the temperature of the device is accurately being measured * Handle products only after the temperature has cooled off * Finish soldering within 3 s * Handling after reflow should be done only after the work surface has been cooled off Rev. 1.9, 26-Apr-2018 6 Document Number: 82496 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP752..W, TSOP754..W www.vishay.com Vishay Semiconductors VISHAY LEAD (Pb)-FREE REFLOW SOLDER PROFILE max. 260 C 255 C 240 C 2nd line Temperature (C) 250 245 C 217 C 1000 200 max. 20 s 150 max. 120 s max. 100 s 100 100 Max. ramp up 3 C/s 50 Max. ramp down 6 C/s Max. 2 cycles allowed 10 0 50 0 100 150 200 250 300 Time (s) 19800 3.6 0.3 TAPING VERSION TSOP..TR DIMENSIONS in millimeters 16 1.75 7.5 O 1.5 4 Direction of feed 8 2 O 1.5 technical drawings according to DIN specifications Drawing-No.: 9.700-5342.01-4 Issue: 2; 12.06.13 Rev. 1.9, 26-Apr-2018 7 Document Number: 82496 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP752..W, TSOP754..W www.vishay.com Vishay Semiconductors 3 0.3 TAPING VERSION TSOP..TT DIMENSIONS in millimeters 16 1.75 7.5 O 1.5 4 Direction of feed 8 2 O 1.5 min. technical drawings according to DIN specifications Drawing-No.: 9.700-5341.01-4 Issue: 3; 06.10.15 Rev. 1.9, 26-Apr-2018 8 Document Number: 82496 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP752..W, TSOP754..W www.vishay.com Vishay Semiconductors REEL DIMENSIONS in millimeters 16734 LEADER AND TRAILER DIMENSIONS in millimeters Trailer no devices Leader devices no devices End Start min. 200 min. 400 96 11818 COVER TAPE PEEL STRENGTH LABEL According to DIN EN 60286-3 Standard bar code labels for finished goods 0.1 N to 1.3 N The standard bar code labels are product labels and used for identification of goods. The finished goods are packed in final packing area. The standard packing units are labeled with standard bar code labels before transported as finished goods to warehouses. The labels are on each packing unit and contain Vishay Semiconductor GmbH specific data. 300 10 mm/min. 165 to 180 peel angle Rev. 1.9, 26-Apr-2018 9 Document Number: 82496 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP752..W, TSOP754..W www.vishay.com Vishay Semiconductors VISHAY SEMICONDUCTOR GmbH STANDARD BAR CODE PRODUCT LABEL (finished goods) PLAIN WRITING ABBREVIATION LENGTH INO SEL BATCH COD PTC QTY ACC PCK MIXED CODE xxxxxxx+ TYPE N N X N TYPE X N X - 18 8 3 10 3 (YWW) 2 8 Company logo LENGTH 8 2 3 8 21 LENGTH 3 3 10 1 17 Item-description Item-number Selection-code LOT-/serial-number Data-code Plant-code Quantity Accepted by Packed by Mixed code indicator Origin LONG BAR CODE TOP Item-number Plant-code Sequence-number Quantity Total length SHORT BAR CODE BOTTOM Selection-code Data-code Batch-number Filter Total length DRY PACKING In case of moisture absorption, the devices will recover to the former condition by drying under the following condition: The reel is packed in an anti-humidity bag to protect the devices from absorbing moisture during transportation and storage. 192 h at 40 C + 5 C / - 0 C and < 5 % RH (dry air / nitrogen) or 96 h at 60 C + 5 C and < 5 % RH for all device containers or 24 h at 125 C + 5 C not suitable for reel or tubes. Aluminum bag Label An EIA JEDEC(R) standard J-STD-020 level 4 label is included on all dry bags. LEVEL CAUTION Reel This bag contains MOISTURE-SENSITIVE DEVICES 15973 4 1. Shelf life in sealed bag: 12 months at < 40 C and < 90 % relative humidity (RH) FINAL PACKING 2. After this bag is opened, devices that will be subjected to soldering reflow or equivalent processing (peak package body temp. 260 C) must be 2a. Mounted within 72 hours at factory condition of < 30 C/60 % RH or 2b. Stored at < 5 % RH The sealed reel is packed into a cardboard box. RECOMMENDED METHOD OF STORAGE 3. Devices require baking befor mounting if: Humidity Indicator Card is > 10 % when read at 23 C 5 C or 2a. or 2b. are not met. Dry box storage is recommended as soon as the aluminum bag has been opened to prevent moisture absorption. The following conditions should be observed, if dry boxes are not available: 4. If baking is required, devices may be baked for: 192 hours at 40 C + 5 C/- 0 C and < 5 % RH (dry air/nitrogen) or 96 hours at 60 C 5 C and < 5 % RH for all device containers or 24 hours at 125 C 5 C not suitable for reels or tubes Bag Seal Date: (If blank, see barcode label) * Storage temperature 10 C to 30 C * Storage humidity 60 % RH max. Note: Level and body temperature defined by EIA JEDEC Standard J-STD-020 After more than 72 h under these conditions moisture content will be too high for reflow soldering. Rev. 1.9, 26-Apr-2018 22522 EIA JEDEC standard J-STD-020 level 4 label is included on all dry bags 10 Document Number: 82496 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP752..W, TSOP754..W www.vishay.com Vishay Semiconductors VISHAY SEMICONDUCTORS STANDARD BAR CODE LABELS ESD PRECAUTION Proper storage and handling procedures should be followed to prevent ESD damage to the devices especially when they are removed from the antistatic shielding bag. Electrostatic sensitive devices warning labels are on the packaging. The Vishay Semiconductors standard bar code labels are printed at final packing areas. The labels are on each packing unit and contain Vishay Semiconductors specific data. 22178 Rev. 1.9, 26-Apr-2018 11 Document Number: 82496 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SMD Tape and Reel www.vishay.com Vishay Semiconductors Tape and Reel Standards for Surface-Mount IR Receiver Modules NUMBER OF COMPONENTS Vishay Semiconductor surface-mount IR receivers are packaged on tape and reel. The following specification is based on IEC publication 286, which takes the industrial requirements for automatic insertion into account. A. Panhead: quantity per reel: TT, top view package, 1190 pcs TR, side view package, 1120 pcs Absolute maximum ratings, mechanical dimensions, optical and electrical characteristics for taped devices are identical to the basic catalog types and can be found in the specifications for untaped devices. B. Heimdall: quantity per reel: TT, top view package, 2200 pcs TR, side view package, 2300 pcs C. Heimdall without lens: quantity per reel: PACKAGING WTT, top view package, 2200 pcs The tapes of components are available on reels. Each reel is marked with labels which contain the following information: WTR, side view package, 2300 pcs D. Belobog: quantity per reel: - Vishay TT1, top view package, 1800 pcs - Type - Group E. Belobog with shield: quantity per reel: - Tape code, normally part of type name TT1, top view package, 1500 pcs - Production code F. Minimold DF1P: quantity per reel: - Quantity DF1P, 1100 pcs G. TVCastSMD TR1: quantity per reel: MISSING COMPONENTS TR1, side view package, 2000 pcs Up to 3 consecutive components may be missing if the gap is followed by at least 6 components. A maximum of 0.5 % of the components per reel quantity may be missing. At least 5 empty positions are present at the start and the end of the tape to enable tape insertion. ORDER DESIGNATION Tensile strength of the tape: > 15 N Example: The type designation of the device is extended by TT or TT1 for top view or TR for side view. TSOP6238TR (reel packing) TSOP75238TR (reel packing) TSOP75338WTT (reel packing) TSOP57438TT1 (reel packing) TSOP57238HTT1 (reel packing) TSOP39438TR1 (reel packing) Rev. 2.5, 08-Mar-18 1 Document Number: 80125 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SMD Tape and Reel www.vishay.com Vishay Semiconductors REEL DIMENSIONS FOR PANHEAD, HEIMDALL, AND TVCASTSMD TR in millimeters 16734 Note * The body structure of the reel can vary Rev. 2.5, 08-Mar-18 2 Document Number: 80125 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SMD Tape and Reel www.vishay.com Vishay Semiconductors TAPING VERSION TSOP..TT (TOP VIEW) DIMENSIONS in millimeters A. Panhead (TSOP36...TT, TSSP....TT, TSOP6...TT, TSOP16...TT, TSOP96...TT) 16584 Rev. 2.5, 08-Mar-18 3 Document Number: 80125 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SMD Tape and Reel www.vishay.com Vishay Semiconductors TAPING VERSION TSOP..TT (TOP VIEW) DIMENSIONS in millimeters 3.65 0.3 B. Heimdall (TSOP75...TT, TSOP77...TT, TSSP77...TT, TSOP15...TT, TSOP95...TT) 16 1.75 7.5 O 1.5 4 8 Direction of feed 2 O 1.5 technical drawings according to DIN specifications Drawing-No.: 9.700-5338.01-4 Issue: 4; 12.06.13 Rev. 2.5, 08-Mar-18 4 Document Number: 80125 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SMD Tape and Reel www.vishay.com Vishay Semiconductors TAPING VERSION TSOP..TT (TOP VIEW) DIMENSIONS in millimeters 3 0.3 C. Heimdall without lens (TSOP75...WTT, TSOP77...WTT, TSSP77...WTT, TSOP15...WTT, TSOP95...WTT) 16 1.75 7.5 O 1.5 4 Direction of feed 8 2 O 1.5 min. technical drawings according to DIN specifications Drawing-No.: 9.700-5341.01-4 Issue: 3; 06.10.15 Rev. 2.5, 08-Mar-18 5 Document Number: 80125 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SMD Tape and Reel www.vishay.com Vishay Semiconductors TAPING VERSION TSOP..TT1 (TOP VIEW) DIMENSIONS in millimeters D. Belobog (TSOP37...TT1, TSOP57...TT1, TSOP17...TT1, TSOP97...TT1) Tape and reel dimensions: O 60 min. Unreel direction Reel size "Y" TT1 O 180 2 = 1800 pcs. Tape position coming out from reel 2 OY 0 .5 O 21 0.8 O 13 0.2 Label posted here (12.4) 18.4 max. Parts mounted Empty leader 400 mm min. 100 mm min. with cover tape Leader and trailer tape: Empty trailer 200 mm min. Direction of pulling out Technical drawings according to DIN specifications (O 1.5) (2) (5.5) (0.3) (4) Drawing-No.: 9.700-5347.01-4 Issue: 2; 07.03.18 Rev. 2.5, 08-Mar-18 12 0.3 (8) (1.2) (1.75) X 2:1 Not indicated tolerances 0.1 6 Document Number: 80125 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SMD Tape and Reel www.vishay.com Vishay Semiconductors TAPING VERSION TSOP..TT1 (TOP VIEW) DIMENSIONS in millimeters E. Belobog with shield (TSOP37...HTT1, TSOP57...HTT1, TSOP17...HTT1, TSOP97...HTT1) Tape and reel dimensions: Reel size "Y" TT1 O 180 2 = 1500 pcs. X 2 O 60 min. Unreel direction Tape position coming out from reel OY 0.5 O 21 0.8 O 13 0.2 Label posted here (12.4) 18.4 max. Parts mounted Empty leader 400 mm min. 100 mm min. with cover tape Leader and trailer tape: Empty trailer 200 mm min. Direction of pulling out Technical drawings according to DIN specifications (O 1.5) (2) (5.5) (0.3) (4) Drawing-No.: 9.700-5380.01-4 Issue: 3; 07.03.18 Rev. 2.5, 08-Mar-18 (12) (8) (1.75) X 2:1 Not indicated tolerances 0.1 7 Document Number: 80125 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SMD Tape and Reel www.vishay.com Vishay Semiconductors TAPING VERSION TSOP..DF1P (SIDE VIEW) DIMENSIONS in millimeters F. Minimold DF1P (TSOP33...DF1P, TSOP53...DF1P, TSOP13...DF1P, TSOP93...DF1P) +3 -0 Technical drawing according to DIN specifications Form of the leave open of the wheel is supplier specific. Dimensions according to IEC EN 60 286-3 O 12 .8 m 1.5 in. mi n. O 60 min. O 330 +0 -4 24.4 Tape width: 24 20 .2 Reel hub 2:1 n. (2) (1.55) B (0.4) (12) (1.5 min.) A A (11.75) (24) (11.5) (4) Drawing-No.: 9.800-5052.V3-4 Issue: 1; 17.12.02 mi (1.75) O (5.25) B B-B A-A Drawing-No.: 9.700-5399.01-4 Issue: 1; 30.06.16 Rev. 2.5, 08-Mar-18 (6.08) 8 Document Number: 80125 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SMD Tape and Reel www.vishay.com Vishay Semiconductors TAPING VERSION TSOP..TR (SIDE VIEW) DIMENSIONS in millimeters G. TVCastSMD TR1 (TSOP59...TR1, TSOP39...TR1, TSOP19...TR1, TSOP99...TR1) (1.7) (9.75) (2.85) A-A (2 : 1) (16) (7.5) B-B (2 : 1) (1.75) (7.05) B B A (2) (O 1) Direction of feed (4) (12) A O 1.5 Technical drawings according to DIN specification. Drawing-No.: GO-100220.10_Z Issue B: 08.02.17 Rev. 2.5, 08-Mar-18 9 Document Number: 80125 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SMD Tape and Reel www.vishay.com Vishay Semiconductors TAPING VERSION TSOP..TR (SIDE VIEW) DIMENSIONS in millimeters A. Panhead (TSOP36...TR, TSSP6...TR, TSOP6...TR, TSOP16...TR, TSOP96...TR) 16585 Rev. 2.5, 08-Mar-18 10 Document Number: 80125 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SMD Tape and Reel www.vishay.com Vishay Semiconductors TAPING VERSION TSOP..TR (SIDE VIEW) DIMENSIONS in millimeters 0.3 3.6 B. Heimdall (TSSP7...., TSOP75...TR, TSOP77...TR, TSSP7....TR, TSOP15...TR, TSOP95...TR) 16 7.5 1.75 1.34 ref. O 1.5 4 Direction of feed 8 2 O 1.5 min. technical drawings according to DIN specifications Drawing-No.: 9.700-5337.01-4 Issue: 2; 06.10.15 Rev. 2.5, 08-Mar-18 11 Document Number: 80125 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SMD Tape and Reel www.vishay.com Vishay Semiconductors TAPING VERSION TSOP..TR (SIDE VIEW) DIMENSIONS in millimeters 3.6 0.3 C. Heimdall without lens (TSOP75...WTR, TSOP77...WTR, TSSP...WTR, TSOP15...WTR, TSOP95...WTR) 16 1.75 7.5 O 1.5 4 Direction of feed 8 2 O 1.5 technical drawings according to DIN specifications Drawing-No.: 9.700-5342.01-4 Issue: 2; 12.06.13 Rev. 2.5, 08-Mar-18 12 Document Number: 80125 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SMD Tape and Reel www.vishay.com Vishay Semiconductors LEADER AND TRAILER DIMENSIONS in millimeters Trailer no devices Leader devices no devices End Start min. 200 min. 400 96 11818 COVER TAPE REEL STRENGTH LABEL According to DIN EN 60286-3 Standard bar code labels for finished goods 0.1 N to 1.3 N The standard bar code labels are product labels and used for identification of goods. The finished goods are packed in final packing area. The standard packing units are labeled with standard bar code labels before transported as finished goods to warehouses. The labels are on each packing unit and contain Vishay Semiconductor GmbH specific data. 300 mm/min. 10 mm/min. 165 to 180 peel angle VISHAY SEMICONDUCTOR GmbH STANDARD BAR CODE PRODUCT LABEL (finished goods) PLAIN WRITING ABBREVIATION LENGTH Item-description - 18 INO 8 Item-number Selection-code SEL 3 BATCH 10 Data-code COD 3 (YWW) Plant-code PTC 2 Quantity QTY 8 Accepted by ACC - Packed by PCK - MIXED CODE - xxxxxxx+ Company logo TYPE LENGTH LOT-/serial-number Mixed code indicator Origin LONG BAR CODE TOP Item-number N 8 Plant-code N 2 Sequence-number X 3 Quantity N 8 Total length - 21 TYPE LENGTH Selection-code X 3 Data-code N 3 Batch-number X 10 Filter - 1 Total length - 17 SHORT BAR CODE TOP Rev. 2.5, 08-Mar-18 13 Document Number: 80125 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SMD Tape and Reel www.vishay.com Vishay Semiconductors DRY PACKAGING The reel is packed in an anti-humidity bag to protect the devices from absorbing moisture during transportation and storage. LEVEL CAUTION This bag contains MOISTURE-SENSITIVE DEVICES Aluminum bag 4 1. Shelf life in sealed bag: 12 months at < 40 C and < 90 % relative humidity (RH) 2. After this bag is opened, devices that will be subjected to soldering reflow or equivalent processing (peak package body temp. 260 C) must be 2a. Mounted within 72 hours at factory condition of < 30 C/60 % RH or 2b. Stored at < 5 % RH Label 3. Devices require baking befor mounting if: Humidity Indicator Card is > 10 % when read at 23 C 5 C or 2a. or 2b. are not met. 4. If baking is required, devices may be baked for: 192 hours at 40 C + 5 C/- 0 C and < 5 % RH (dry air/nitrogen) or 96 hours at 60 C 5 C and < 5 % RH for all device containers or 24 hours at 125 C 5 C not suitable for reels or tubes Reel Bag Seal Date: (If blank, see barcode label) 15973 Note: Level and body temperature defined by EIA JEDEC Standard J-STD-020 22522 RECOMMENDED METHOD OF STORAGE EIA JEDEC standard JSTD-020 level 4 label is included on all dry bags Dry box storage is recommended as soon as the aluminum bag has been opened to prevent moisture absorption. The following conditions should be observed, if dry boxes are not available: ESD PRECAUTION Proper storage and handling procedures should be followed to prevent ESD damage to the devices especially when they are removed from the antistatic shielding bag. Electrostatic sensitive devices warning labels are on the packaging. * Storage temperature 10 C to 30 C * Storage humidity 60 % RH max. After more than 72 h under these conditions moisture content will be too high for reflow soldering. VISHAY SEMICONDUCTORS STANDARD BAR CODE LABELS In case of moisture absorption, the devices will recover to the former condition by drying under the following condition: The Vishay Semiconductors standard bar code labels are printed at final packing areas. The labels are on each packing unit and contain Vishay Semiconductors specific data. 192 h at 40 C + 5 C / - 0 C and < 5 % RH (dry air / nitrogen) or 96 h at 60 C + 5 C and < 5 % RH for all device containers or 24 h at 125 C + 5 C not suitable for reel or tubes. An EIA JEDEC(R) standard JSTD-020 level 4 label is included on all dry bags. 16962 OUTER PACKAGING The sealed reel is packed into a pizza box. CARTON BOX DIMENSIONS in millimeters Length Thickness Width 22127 Pizza box (SMD and heimdall) (taping in reels) Rev. 2.5, 08-Mar-18 THICKNESS WIDTH LENGTH 50 340 340 14 Document Number: 80125 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. (c) 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 08-Feb-17 1 Document Number: 91000 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Vishay: TSOP75233WTR TSOP75240WTR TSOP75430WTR TSOP75433WTR TSOP75440WTR TSOP75456WTR TSOP75438WTT TSOP75238WTT TSOP75436WTT TSOP75236WTT TSOP75230WTT TSOP75233WTT TSOP75240WTT TSOP75256WTT TSOP75430WTT TSOP75433WTT TSOP75440WTT TSOP75456WTT