Preliminary DN-900 Series - 900 MHz RS-232C, RS-485/RS-232C and USB Serial Modems - Optional 128-Bit AES Encryption - Point-to-point, Point-to-multipoint, Peer-to-peer and Tree-routing Network Capabilities - Frequency Hopping Spread Spectrum Transceiver - Transceiver Housed in a NEMA 4X/IP66 Waterproof Case - RF Data Rate Configurable from 38.4 to 500 kbps - Transmitter Power up to 1.58 W EIRP using Internal Antenna - FCC and Canadian IC Certified for Unlicensed Operation 900 MHz Wireless Serial Modems The DN-900 series 900 MHz serial modems provide ready-to-use solutions for robust wireless data communications in the 900 MHz ISM band. There are currently three products in the DN-900 series, the DN-900G, the DN-900I and the DN-900U. The DN-900G provides an RS-232C serial interface. The DN-900I offers a two-wire, multi-drop RS-485 interface plus a selectable RS-232C interface for configuration programming. The DN-900U provides a USB interface. DN-900 series modems are based on RFM's DNT900 frequency hopping spread spectrum (FHSS) transceiver, and can communicate with other DNT900-based RFM products as well as customer developed products. DN-900 series modems consist of a radio module in a NEMA 4X/IP66 waterproof case connected to a serial interface adapter by a power and signal cable that allows the radio module to be located remotely at a point of good RF propagation. DN-900 series modems are well-suited for serial data networks carrying moderate traffic that need robust communications in locations with non-ideal RF propagation and/or where RF interference or noise are present. DN-900 Series Absolute Maximum Ratings Rating Value Power Supply Input Voltage Range -0.5 to +24 Non-Operating Ambient Temperature Range -40 to +85 Units V o C DN-900 Series Specifications Characteristic Operating Frequency Range Hop Dwell Time Number of RF Channels in a Subband Modulation RF Data Transmission Rates Standard Antenna Sym Notes Minimum Maximum Units 902.75 Typical 927.25 MHz 5 200 ms 50 FSK 38.4, 115.2, 200 and 500 kbps Internal 2 dBi directional antenna Receiver Sensitivity through 2 dBi Antenna: 10-5 BER @ 38.4 kb/s -110 dBm -5 -100 dBm -5 -96 dBm 1.58, 15.8, 100, 395, 790, 1580 mW 1.58, 15.8, 135 mW 10 BER @ 200 kb/s 10 BER @ 500 kb/s EIRP Output Power Levels through 2 dBi Antenna: 38.4 to 200 kbps 500 kbps www.RFM.com E-mail: info@rfm.com (c) 2012 by RF Monolithics, Inc. Page 1 of 5 DN-900 Series - 07/30/12 DN-900 Series Specifications Characteristic Sym Notes Minimum Typical Maximum Optional External Antenna Connector Reverse TNC (RTNC) External Antenna Impedance 50 ohms, VSWR < 3:1 Units Direct Receiver Sensitivity through RTNC Connector: 10-5 BER @ 38.4 kb/s -108 dBm -5 -98 dBm -5 -94 dBm 1, 10, 63, 250, 500, 1000 mW 1, 10, 85 mW 10 BER @ 200 kb/s 10 BER @ 500 kb/s Direct Output Power Levels through RTNC Connector: 38.4 to 200 kbps 500 kbps Network Topologies Point-to-Point, Point-to-Multipoint, Peer-to-Peer, Tree-Routing Access Scheme Number of Remote Nodes, TDMA Mode TDMA/CSMA 1 16 Number of Remote Nodes, CSMA Mode Limited only by traffic density DN-900G RS-232C Configuration 9-pin connector, hardware flow control optional DN-900I RS-232C Configuration 3-wire, no hardware flow control DN-900I RS-485 Configuration 2-wire, multi-drop capable DN-900U USB Configuration Serial Port Baud Rates USB Type B connector 1.2, 2.4, 4.8, 9.6, 19.2, 28.8, 38.4, 57.6, 76.8, 115.2, 230.4, 460.8 kbps 4, 50, 100, 300 ft Signal Cable Length Options (see Ordering Guide on Page 5) DC Power Supply Voltage Range, up to 50 ft signal cable +6 +24 Vdc DC Power Supply Voltage Range, 50 ft to 300 ft cable +12 +24 Vdc DC Power Supply Ripple, 1.5 A load 250 mVP-P Peak Transmit Mode DC Power 6.8 W Average Receive Mode Power: Base, Continuous Data Stream 760 mW Remote, Linked, No Data 317 mW Remote, Continuous Data Stream, 9.6 kbps 345 mW Remote, Continuous Data Stream, 115.2 kbps 428 mW 3.85 x 1.70 x 0.85 inches ( 80 x 43 x 22 mm) Interface Adapter Nominal Dimensions Radio Module Case Rating NEMA 4X/IP66 outdoor enclosure 5.15 x 5.00 x 1.40 inches (131 x 127 x 36 mm) Radio Module Nominal Dimensions Radio Module Mounting Flange with pre-drilled mounting holes; mount flange to mast with bolts or hose clamps Operating Temperature Range -40 85 o Operating Relative Humidity Range, Non-condensing 10 90 % www.RFM.com E-mail: info@rfm.com (c) 2012 by RF Monolithics, Inc. C Page 2 of 5 DN-900 Series - 07/30/12 Figure 1 DN-900 Series Modem Operation The DN-900 series 900 MHz modems provide high performance, ready-to-use solutions for robust wireless data communications in the 900 MHz ISM band. There are currently three products in the DN-900 series, the DN-900G, the DN-900I, and the DN-900U. The DN-900G provides an RS-232C serial interface with optional flow control. The DN-900I offers a two-wire, multi-drop RS-485 interface plus a selectable three-wire RS-232C interface for configuration programming. The DN-900U provides a USB interface. DN-900 series modems are based on RFM's DNT900 frequency hopping spread spectrum (FHSS) transceiver, and can communicate with other DNT900-based RFM products, as well as customer developed products. As shown in Figure 1, DN-900 series modems consist of a radio module in a NEMA 4X/IP66 waterproof case with an internal 2 dBi directional antenna, a signal cable that carries power and data, and an interface adaptor that includes a power supply connector and the appropriate serial data connector. The radio module can optionally be provided with a RTNC antenna connector in lieu of the internal antenna (see Ordering Guide on Page 5). DN-900 serial modems with the RTNC connector are compatible with RFM's complete line of 900 MHz antennas, allowing extended operating range where allowed by local regulations. www.RFM.com E-mail: info@rfm.com (c) 2012 by RF Monolithics, Inc. DN-900 series modems are supplied with a 110/220 VAC wall-plug power supply that includes an international plug set. Optionally, DN-900 series modems can be powered from a user-supplied DC source as described in the specifications table. The signal cable can specified as 4, 50, 100 or 300 feet in length (see Ordering Guide on Page 5), which allows the radio module to be located remotely indoors or outdoors at a point of good RF propagation. DN-900 modems can transmit data from 38.4 to 500 kbps, and the transmitter output power can be set from 1.58 mW to 1.58 W EIRP when using the internal antenna. DN-900 series modems are well-suited for serial data networks carrying moderate traffic that need robust communications in locations with non-ideal RF propagation and/or where RF interference or noise are present. DN-900 serial modems can operate in point-to-point, point-to-multipoint, peer-to-peer and tree routing DNT900-based wireless networks. DN-900 data modems are shipped configured to transmit transparent data, which requires no protocol formatting. All that is required to set up a transparent point-to-point serial data link to configure one modem as a base unit using a simple PC-based utility. DN-900 series modems can also operate in protocol mode, which is supported by a rich set of configuration parameters that allow a wide range of network layouts and configurations to be optimized. Page 3 of 5 DN-900 Series - 07/30/12 DN-900G/DN-900U Power Connector and LED Description Ref Name I/O Description T +PWR I The center coaxial conductor (tip) is the positive DC power input. R GND - The outer coaxial conductor (ring) is the DC power ground. G PWR O Green LED indicates the unit is powered. A LINK O Amber LED indicates the unit is linked. DN-900G Serial Port DB9 Connector Description Pin Name I/O Description 1 DCD O This pin is an output indicating the modem is linked to the radio network. 2 RADIO_TXD O This pin is the DN-900G serial data output. 3 RADIO_RXD I This pin is the DN-900G serial data input. 4 DTR I This pin is the data terminal ready input from the DN-900G host. 5 GND - This pin is signal ground. 6 - - No connection. 7 HOST_RTS I This pin is the request to send input from the DN-900G host. 8 HOST_CTS O This pin is the clear to send output from the DN-900G. 9 - - No connection. DN-900I Serial Port Terminal Block Description Pin Name I/O Description 1 +PWR I This terminal is the positive power supply input, +6 to +24 V. 2 GND - This terminal is a power supply and signal ground. 3 485 EN I When this terminal is unconnected, serial operation is RS-232C. When this terminal is grounded to terminal 2 or 4, serial operation is RS-485. 4 GND - This terminal is a power supply and signal ground. 5 TX/A O This terminal transmits data to the host (RS-232C TxD or RS-485 A signal). 6 RX/B I This terminal receives data from the host (RS-232C RxD or RS-485 B signal). www.RFM.com E-mail: info@rfm.com (c) 2012 by RF Monolithics, Inc. Page 4 of 5 DN-900 Series - 07/30/12 D N -9 0 0 S e r ie s T r a n s c e iv e r C a s e = 1 .4 0 (3 6 ) 5 .0 0 (1 2 7 ) 4 .4 0 (1 1 2 ) 3 .2 0 (8 1 ) 5 .1 5 (1 3 1 ) D im e n s io n s in in c h e s a n d (m m ) 4 .8 0 (1 2 2 ) Figure 2 DN-900 Serial Modem Part Number Ordering Guide Cable Length, feet Serial Interface Antenna/Connector 4 50 100 300 RS-232C, DB9 Connector Internal 2 dBi Antenna DN-900G-4 DN-900G DN-900G-100 DN-900G-300 RS-232C, DB9 Connector RTNC Connector DN-900GX-4 DN-900GX DN-900GX-100 DN-900GX-300 RS-485/RS-232C, 6-Pin Terminal Block Internal 2 dBi Antenna DN-900I-4 DN-900I DN-900I-100 DN-900I-300 RS-485/RS-232C, 6-Pin Terminal Block RTNC Connector DN900IX-4 DN-900IX DN-900IX-100 DN-900IX-300 USB Type B Connector Internal 2 dBi Antenna DN900U-4 DN-900U DN-900U-100 DN-900U-300 USB Type B Connector RTNC Connector DN900UX-4 DN-900UX DN-900UX-100 DN-900UX-300 Note: Specifications subject to change without notice. Part # M-0900-5000, Rev A www.RFM.com E-mail: info@rfm.com (c) 2012 by RF Monolithics, Inc. Page 5 of 5 DN-900 Series - 07/30/12