APPLICATION NOTE ATAK43001-V1 Development Kit for the ATA664251 Atmel IC ATAN0063 Introduction The development kit for the Atmel(R) ATA664251 IC consists of the PC interface board (ATAB0004A-V2.0) and the Atmel ATA664251 application board (ATAB664251A-V1.0) attached together as one unit. The kit provides users with a quick start guide for prototyping and testing new LIN designs with the Atmel ATA664251 IC. Figure 1. Atmel ATAK43001-V1 Development Kit The Atmel ATA664251 is a system-in-package (SiP) product, which is especially well suited for complete LIN-bus node applications. It is designed specifically for LIN switch applications and includes nearly the complete LIN node. It consists of two ICs in one package supporting highly integrated solutions for in-vehicle LIN networks. The first chip is the ATA664151 LIN system basis chip (SBC), which has an integrated LIN transceiver, a 5V regulator (80mA), a window watchdog, an 8-channel high voltage switch interface with high-voltage current sources and a 16-bit SPI for configuration and diagnosis. The second chip is an Atmel automotive microcontroller from the AVR 8-bit microcontroller series featuring advanced RISC architecture, the Atmel ATtiny167 with 16 Kbytes of Flash memory. All the LIN SBC pins as well as all the AVR microcontroller pins are bonded out to provide customers with the same flexibility for their applications they have when using discrete parts. 9300D-AUTO-03/15 The Atmel(R) LIN SBC ATA664251 has the following features: SBC: LIN master and slave operation possible 3x PWM inputs for direct control of the switch interface sources Up to 40V supply voltage Operating voltage VS = 5V to 27V 8-channel HV switch interface with HV current sources Internal voltage divider for VBattery sensing (2%) 16-bit serial interface (daisy-chain-capable) for configuration and diagnosis Typically 8A supply current during sleep mode Typically 35A supply current in active low-power mode 5V 2% linear low-drop voltage regulator, up to 80mA current capability VCC undervoltage detection (5ms reset time) and watchdog reset logical combined at NRES open drain output LIN high-speed mode for transmission rates up to 200kBit/s Watchdog timer adjustable via external resistor Negative trigger input for watchdog LIN physical layer complies with LIN 2.1 specification and SAE J2602-2 Wake-up capability via LIN bus and CL15 Bus pin is overtemperature and short-circuit protected versus GND and battery Advanced EMC and ESD performance System-level ESD performance conforming with OEM "Hardware Requirements for LIN in Automotive Applications Rev. 1.2" AVR microcontroller: High-performance, low-power AVR(R) 8-bit microcontroller Advanced RISC architecture 123 powerful instructions - in most cases single clock cycle execution 32 x 8 general purpose working registers Fully static operation Non-volatile program and data memories 16 Kbytes of in-system programmable (ISP) program memory flash 512 bytes in-system programmable EEPROM Endurance: 100,000 write/erase cycles 512 bytes internal SRAM Programming lock for self-programming Flash program and EEPROM data security Peripheral features LIN 2.1 and LIN 1.3 controller or 8-bit UART 8-bit asynchronous timer/counter0 2 Endurance: 10,000 write/erase cycles 10-bit clock prescaler One output compare or 8-bit PWM channel 16-bit synchronous timer/counter1 10-bit clock prescaler External event counter Two output compare units or 16-bit PWM channels each driving up to four output pins ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 Master/slave SPI serial interface Universal serial interface (USI) with start condition detector (master/slave SPI, TWI, ...) 10-bit ADC 11 single-ended channels Eight differential ADC channel pairs with programmable gain (8x or 20x) On-chip analog comparator with selectable voltage reference 100A 10% current source (LIN node identification) On-chip temperature sensor Programmable watchdog timer with separate on-chip oscillator Special microcontroller features Dynamic clock switching (external/internal RC/watchdog clock) for power control, EMC reduction DebugWIRE on-chip debug (OCD) system Hardware in-system programmable (ISP) via SPI port External and internal interrupt sources Interrupt and wake-up on pin change Low-power idle, ADC noise reduction, and power-down modes Enhanced power-on reset circuit Programmable brown-out detection circuit Internal calibrated RC oscillator 8MHz 4MHz to 16MHz and 32kHz crystal/ceramic resonator oscillators I/O Speed grade 16 programmable I/O lines 0MHz to 16MHz at 4.5V to 5.5V (automotive temperature range: -40C to +125C) This document has been developed to provide users with start-up information about the Atmel ATAK43001-V1 development kit. For more information about the use of the devices themselves, see the appropriate datasheet. ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 3 1. Development Kit Features The development kit for the Atmel(R) ATA664251 IC has the following features, starting with the features of the Atmel ATA664251 (ATAB664251A-V1) board: All necessary components to put the Atmel ATA664251 into operation are included to simulate and test the real application LEDs connectable to all HV ports Easily adaptable watchdog times by replacing a single resistor 1x RGB LED 8x push-buttons 8x rotary switches Easy access to all pins ISP connector for on-chip ISP (in-system programming) Possibility of selecting between master or slave operation (mounting D2 and R1) Push button included for creating a local wake-up after entering sleep mode Easily adaptable current level of the current sources by replacing a single resistor Ground coulter clip for connecting probes easily when measuring with the oscilloscope The interface board (Atmel ATAB0004A) has the following features: Easy connection to a PC (AT90USB1287 on board) 4 USB interface to PC SBC functions easily configurable via PC GUI ISP connector for in-chip ISP (in-system programming) JTAG connector for on-chip debugging Buzzer On-board RESET button On-board boot loader button to force AVR(R) into DFU mode at reset 16MHz crystal for system clock ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 2. Getting Started The development kit for the Atmel(R) ATA664251 is shipped with the default jumper settings and all accessories required for immediate use. Figure 2-1. Atmel ATAK43001-V1 Development Kit with Reference Points The IC mounted on the PC interface board (AT90USB1287) is preprogrammed with firmware which facilitates testing and gaining familiarity with the basic functions of the kit. The microcontroller within the Atmel ATA664251 (Atmel ATtiny167) is held in reset via jumper J12 and the SCB is controlled via the PC interface board and the demo GUI. First of all the USB drivers and the GUI software have to be installed (please see Section 2.2 "USB Driver Installation" on page 8 and Section 2.1 "GUI Software Installation" on page 7 for more information). After correctly connecting an external 12V DC power supply (reference point 1) to the power connector and connecting the PC interface board to the PC via the supplied USB cable, the kit is ready to use. The Atmel ATA664251 IC starts in active mode, with the VCC voltage regulator, the window watchdog switched on (the latter depends on the VDIV pin, see Section 5.7 "Watchdog Section" on page 39), the AVR core is in reset (reset pin (pin 2) is connected by default to GND via jumper J12). The status of all pins is shown in Table 2-1 on page 6. ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 5 Table 2-1. 6 Overview of Pin Status at Power-Up of the Development Kit Test Point Expected Behavior NTRIG 5V TXD 5V RXD 5V NRES 5ms reset pulse with 165ms period, because the watchdog is not triggered NIRQ 0V MISO 0V MOSI 0V SCK 0V NCS 5V PWM1 0V PWM2 0V PWM3 0V VDIV 0V LIN 12V CL15 0V J16 5.1V J2 5ms reset pulse with 165ms period, because the watchdog is not triggered Additional Information Dependent on the supply voltage (VBAT-0.7V) If jumper J1 (controller board) is set, this jumper should be open. J1 5.1V Default setting, otherwise 3.3V Jxx 0V Default setting: connected to GND VCC (pin 14) 5V Voltage regulator is ON PA0...7 0V AVR is in reset --> I/Os in tristate PB0...7 0V AVR is in reset --> I/Os in tristate CS1...8 0V Switch interface is OFF ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 2.1 GUI Software Installation To install the GUI, execute the setup.exe file and follow the instructions to complete the installation. Select the directory where you want to install the demo and click "Next." Figure 2-2. Selecting the Directory ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 7 After the installation is done, press "Finish." Figure 2-3. Completing the Installation 2.2 USB Driver Installation After connecting the PC interface board to a PC the first time, the required USB drivers must be installed before the kit can be used. Be sure to install the GUI first before installing the USB driver (see Section 2.1 "GUI Software Installation" on page 7). As soon as the PC has detected a new hardware device, the "Hardware Wizard" appears. Select "No, not this time" and then click "Next." Figure 2-4. Selecting "No, not this time" 8 ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 Select "Install from a list or specific location" and then click "Next." Figure 2-5. Selecting "Install from a list or specific location (advanced)" Select "Don't search. I will choose the driver to install." and then click "Next." Figure 2-6. Selecting "Don't search. I will choose the driver to install." ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 9 If more than one driver is found, be sure to select the "Destiny National Instruments" driver and then click "Next." Figure 2-7. Selecting the "Destiny National Instruments" Driver Figure 2-8. Installing the Driver 10 ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 After successfully installing the driver, press the "Finish" button. Figure 2-9. Selecting "Finish" ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 11 2.3 Quick Start User Guide 1. To start working with the kit, execute the Atmel(R) ATA6641_Demo.exe. This can be done either from the "Start" menu or from the folder containing the kit files (see Section 2.1 "GUI Software Installation" on page 7). Before starting the GUI, make sure the correct USB driver (see Section 2.2 "USB Driver Installation" on page 8 for more information) and GUI software are installed and that the power supply and USB are properly connected. The following window is opened so that the user can set up and test all the features of the SBC. Figure 2-10. Atmel ATA664251 Demo GUI at Start-up After starting up the GUI, as standard the SBC is set to low-power mode. This is indicated in Section 5.1 "SBC Section" on page 34 (yellow LED - ActiveLP is ON) in the GUI and on the PC interface board (LED - LD2 is ON (reference point 21)) as well (see Figure 2-12). 2. 12 A quick check to determine everything is working properly can be done by clicking the "Active Mode" button in the SBC section where all "Bit Buttons" in Section 5.5 "I/O Ports Section" on page 36 are checked (please see Figure 2-11) and the following LEDs on the ATAB664251A board (please see Figure 2-12) are turned on: LD1-3 (indicate that CS1 is set to low-side ON) LD7-9 (indicate that CS4 is set to low-side ON) LD13-15 (indicate that CS3 is set to low-side ON) LD19-33 (indicate that CS4-8 are ON) ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 Figure 2-11. Atmel ATA664251 Demo GUI after "Active Mode" Button Is Pressed Figure 2-12. Atmel ATAK43001-V1 Kit LEDs in Active Mode In active mode, the watchdog and a valid trigger signal (35ms) are activated. In addition, the LIN interface is enabled and a default frequency of 10kHz (20kBit/s) is generated on the TXD pin. In order to have a LIN signal approximating a real LIN network, a master pull-up and a master diode (reference point 4) are populated on the board (see Section 3.6.3 "Configuring the Atmel ATAK43001-V1 Kit as a Master or a Slave Node" on page 30). 3. It is relatively easy to change the mode of the SBC. Click one of the three mode buttons in Section 5.1 "SBC Section" on page 34. The current mode is indicated in the GUI (3x LEDs in Section 5.1 "SBC Section" on page 34) and on the PC interface board (reference point 21; LEDs - LD2, LD4, LD4) as well. For more information about the different modes, see Section 5.1 "SBC Section" on page 34 or the ATA664251 datasheet. ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 13 Figure 2-13. Mode Change 4. To better understand the features of the high-voltage I/O ports, try changing various settings for the I/O ports by: Enabling/disabling a specific CSx port (select/deselect the CSE bit and click the appropriate "Configure CSx" button) Configure CS1...3 as low-side or high-side by selecting/deselecting the CSSSM bit and click the appropriate "Configure CS1...3" button Configure one of the CS1...8 ports to be controlled either by PWM signal or not: Select/deselect the CSC bit and click the appropriate "Configure CS1...8" button. Make sure the dedicated PWM1...3 signals in the corresponding section of the GUI have been enabled (for more information, see Section 5. "Atmel ATA664251 Demo GUI Description" on page 33). Double/halve the current of the CS1...8 ports by selecting either "x100" or "x50" for the IMUL bit. Figure 2-14. CSx Port Setting 14 ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 5. The VBattery voltage or the voltage on the I/O ports can be easily measured (one at a time) at the VDIV pin. To do so, select the desired source in the "Voltage Divider" section (at the upper right side of the GUI) that has to be measured and press the "Continual" button for continuous measurement of the selected source. Figure 2-15. Selecting the Voltage Measurement Source 6. For testing purposes and to become familiar with the system, it may be helpful to see the behavior when the watchdog is not triggered correctly. This can be done in two different ways without changing the firmware of the IC: Disable NTRIG frequency (click on the "NTRIG ON/OFF" button) No trigger signal reaches the watchdog and the watchdog generates a reset directly after the lead time td (51k) = 155ms has expired. Re-program the fuse bit Changing the CKDIV8 fuse bit to be programmed changes the microcontroller's internal clock from 16MHz to 2MHz. Because of this the trigger signal generated from the microcontroller does not meet the open window from the window watchdog and a reset is generated. In this case the watchdog generates resets ( 5ms reset pulse with 165ms period) on the NRES pin (displayed also in the GUI in the "Current SBC Status" section). ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 15 3. Hardware Description 3.1 Pin Description - ATAB664251A Board In the following sections, the external elements required for some of the pins are shown and described. See the relevant datasheet for more information about this topic. Note: 3.1.1 The Atmel(R) ATA664251's AVR(R) is held in reset (J12 connected to GND) and it is not supplied (J16 is open). Power Supply In order to get the Atmel ATAB664251A development board running, an external 5V to 27V DC power supply has to be connected to the power connector. The input circuit is protected against inverse polarity with the protection diode D7, resulting in a difference of approximately 0.7V between the VBAT supply voltage and the voltage at the VS pin. In order to avoid false bus messages, undervoltage detection is implemented to disable data transmission via the LIN bus and the switch interface if VVS falls below VVSth. After switching on VS, the IC starts in active mode (for more information, please see also Section 4.1 "Active Mode" in the Atmel ATA664251 datasheet) with the VCC voltage regulator and the window watchdog switched on. 3.1.2 Voltage Regulator (VCC) The internal 5V voltage regulator is capable of driving loads up to 80mA for supplying the microcontroller and other loads. It is protected against overloads by means of current limitation and overtemperature shutdown. In addition, the output voltage is monitored and causes a reset signal at the NRES output pin if it drops below a defined threshold VVCCthun. A safe operating area (SOA) is defined for the voltage regulator because the power dissipation caused by this block might exceed the system's thermal budget (please see the Atmel ATA664251 datasheet for more detailed information). 3.1.3 The Window Watchdog (NTRIG, WD_OSC, and NRES) The watchdog anticipates a trigger signal from the microcontroller at the NTRIG input (negative edge) within a defined time window. If no correct trigger signal is received during the open window, a reset signal (active low) is generated at the NRES output. During silent mode or sleep mode the watchdog is switched off to reduce current consumption. The timing basis of the watchdog is provided by the internal oscillator, whose time period tOSC can be adjusted via the external resistor R2 at the WD_OSC pin. All watchdog-specific timings (t1, t2, td, ...) are based on the value of this resistor. There is a resistor with a value of 51k mounted on the development board by default, resulting in the timing sequence for the integrated watchdog in Figure 3-1. Figure 3-1. Watchdog Timing Sequence with R2 = 51k VCC 5V Undervoltage Reset NRES Watchdog Reset tnres = 4ms treset = 4ms td = 155ms t1 t1 = 20.6ms t2 = 21ms twd NTRIG ttrig > 200ns 16 ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 t2 Replacing the resistor R2 results in a frequency change of the internal oscillator. This in turn results in different watchdog timing. The following formula demonstrates how the frequency of the internal oscillator depends on the value of the resistor R2. For more information, see the Atmel ATA664251 datasheet. The resistor Rwd_osc in the datasheet corresponds to resistor R2 on the board: tOSC [RWD_OSC] = 0.405 RWD_OSC - 0.0004 (RWD_OSC)2 tOSC in s RWD_OSC in k With the values given in the datasheet, all relevant watchdog times (such as the open window and closed window) can be calculated using tOSC. In general, the AT90USB1287 is shipped with an oscillator start-up time of 65ms. Due to the extra-long lead time of 155ms it should be possible in almost all cases to meet the first open window of the watchdog. If more time is needed, the 65ms default start-up time of the microcontroller can be reduced via the fuse bits to 4.1ms or even 0ms. The IC mounted on the board is shipped preset to a start-up time of 65ms. 3.1.4 The LIN Interface (LIN, TXD, and RXD) A low-side driver with internal current limitation and thermal shutdown, and an internal pull-up resistor in compliance with the LIN 2.1 specification are implemented. The allowed voltage range is from -30V to +40V. Reverse currents from the LIN bus to VS are suppressed, even in the event of GND shifts or battery disconnection. The LIN receiver thresholds are compatible with the LIN protocol specification. The fall time from recessive to dominant bus state and the rise time from dominant to recessive bus state are slope-controlled. For higher bit rates the slope control can be switched off by setting the SPI-bit LSME. Then the slope time of the LIN falling edge is < 2s. The slope time of the rising edge is highly dependent on the capacitive load and the pull-up resistance at the LIN line. To achieve a high bit rate Atmel recommends using a small external pull-up resistor (500) and a small capacitor. This allows very fast data transmission of up to 200kBit/s, e.g., for electronic control tests of the ECU, microcontroller programming, or data download. In this high-speed mode superior EMC performance is not guaranteed. Note: The internal pull-up resistor is only switched on in active mode and when the LIN transceiver is activated by the LINE bit (active mode with LIN bus transceiver). Because the two TXD and RXD pins on the LIN SBC are controlled by the microcontroller's LIN/UART, they are connected to the corresponding TXD and RXD pins on the microcontroller and can be monitored at these pins. Test points have been provided on the development board. 3.1.4.1 TXD Input Pin (LIN SBC) The TXD pin is the microcontroller interface for controlling the state of the LIN output. TXD must be pulled to ground in order to keep the LIN bus in the dominant state. If TXD is high or not connected (internal pull-up resistor), the LIN output transistor is turned off and the bus is in recessive state. If configured, an internal timer prevents the bus line from being constantly driven in the dominant state. If TXD is forced to low for longer than tDOM, the LIN bus driver is switched back to recessive state. TXD has to be switched to high for at least tTOrel to reactivate the LIN bus driver (by resetting the time-out timer). As mentioned above, this time-out function can be disabled via the SPI configuration register in order to achieve any long dominant state on the connected line (such as PWM transmission or low bit rates). ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 17 3.1.4.2 RXD Output Pin (LIN SBC) This output pin reports the state of the LIN bus to the microcontroller. SLIN high (recessive state) is reported by a high level, LIN low (dominant state) is reported by a low level at RXD. The output has push-pull characteristics, meaning no external time-defining measures are required. The RXD pin is at high level during disabled LIN-PHY states (configuration bit "LINE" = 0). Please note that the signal on the RXD pin is not valid for a certain period of time upon activation of the LIN transceiver (tRXDinvalid). Figure 3-2. RXD Timing upon Transceiver Enable NCS SPI word with LINE = 1 RXD X LIN bus state 0 = DOM --- 1 = REC tRXDinvalid RXD is switched off in sleep and unpowered mode. 3.1.5 Interrupt Request Output Pin (NIRQ) The interrupt request output pin is an open drain output and switches to low whenever a chip-internal event occurs that is set up to trigger an interrupt. A power-up, a wake-up over LIN bus, a change in a switch state, or an overtemperature condition are examples of such events. The pin remains at ground until the end of the next SPI command, at which point the interrupt source is passed to the SPI master. 3.1.6 CL_15 (LIN SBC) This CL15 pin is a high-voltage input that can be used to wake up the device from sleep mode. It is an edge-sensitive pin (low-to-high transition). Thus, even if CL15 pin is at high voltage (VCL15 > VCL15th), it is possible to switch to sleep mode. The CL 15 pin is usually connected to the ignition for generating a local wake-up in the application if the ignition is switched on. If not needed, the CL15 pin should be tied directly to ground. A debounce timer with a value tdebCL15 of typically 160s is implemented. The pin state (CL15 ON or OFF) can be read out through the SPI interface. 3.1.7 VBATT Pin The VBATT is a high-voltage input pin for performing measurements using a voltage divider. The latter provides a lowvoltage signal at the VDIV pin that is linearly dependent on the input voltage. In an application with battery voltage monitoring, this pin is connected in series to VBattery via a 51 resistor and a 10nF capacitor to GND. The divider ratio is 1:4. This ratio results in maximum output voltages on the VDIV pin when 20V is reached at the input. 3.1.8 NRES Output Pin (LIN SBC) and PB6/Reset Input Pin (Microcontroller at the PC Interface Board) The NRES reset output pin is an open-drain output and switches to low during a VCC undervoltage event or a watchdog timing window failure. Please note the reset hold time of typically 4ms has disappeared after the undervoltage condition. The PB6/reset input pin already has a pull-up resistor included with resistance between 30k and 60k. The NRES output pin of the LIN SBC is connected by default to the PB6 input pin of the microcontroller at the PC Interface board. The NRES pin can be connected to the reset pin of the microcontroller via the JP2 jumper (PC interface board). An additional 10k pull-up resistor is included on the development board to have a defined value of the NRES output in case the PJ2 is left open. Because the NRES output is an open-drain output, it is not necessary to remove the J2 jumper (only if placed on position 1 and 2) during programming or debugging of the microcontroller. 18 ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 3.1.9 VDIV Input/Output Pin This pin handles two different functions. During the VCC start-up and watchdog reset phase (pin NRES driven to LOW), the pin acts as the input and determines the setting of the WDD bit within the SPI configuration register (see Figure 3-3). In other words, if the window watchdog operation were disabled directly after power-up (e.g., for microcontroller programming or debugging purposes), the VDIV pin would have to be tied to the HIGH level until the reset phase ends (pin NRES has a positive slope from LOW to HIGH). In other cases, such as when the VDIV pin is not driven actively by the application, the signal is assessed as LOW and the WDD bit (watchdog disable) is thus also low and the window watchdog is operational (see Figure 3-3). Figure 3-3. WDD Configuration Bit Setup During VCC Start-up NRES "LOW" from VCC startup VDIV (driven externally) WDD config bit state Logic Level "A" X Z (high imp.) Logic Level "A" During normal operation, this pin provides a low-voltage signal for the ADC such as for a microcontroller. It is sourced either by the VBATT pin or one of the switch input pins CS1 to CS8. An external ceramic capacitor is recommended for low-pass filtering of this signal (10nF mounted on the board by default; depending on the timings in the current application, this value should be adjusted). If selected in the configuration register of the SPI, this pin guarantees a voltage- and temperature-stable output ratio of the selected test input and is available in all modes except sleep mode. Please note that the current consumption values in the active low-power mode of the Atmel ATA664251 indicated in the electrical characteristics lose their validity if the VDIV output pin is being used in this low-power mode. The voltage on this pin is actively clamped to VCC if the input value would lead to higher values. 3.1.10 IREF Output Pin This pin is the connection for an external resistor toward ground. It provides regulated voltage which causes a resistordependent current to be used as reference for the current sources in the switch interface I/O ports. Fail-safe circuitry detects if the resistor is missing or if there is a short circuit toward ground or VCC on this pin. An internal fail-safe current is generated in this event. 3.1.11 CS1 to CS8 High-Voltage Input/Output Pins These pins are intended for contact monitoring and/or constant current sourcing. A total of eight I/Os (pins CS1 through CS8) are available, of which three (CS1, CS2, and CS3) can be configured either as current sources (such as for switches toward ground) or as current sinks (such as for switches toward battery). The other five pins (CS4 to CS8) have current sourcing capability. Apart from a high-voltage (HV) comparator for simple switches, the I/Os are also equipped with a voltage divider to enable analog voltage measurements on HV pins by using the ADC of the application's microcontroller. Also, each input can trigger an interrupt upon state change even while low-power mode is active. ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 19 3.1.12 PWM1...3 Input Pins These pins can be used to control the switch interface current sources directly, such as for pulse width-modulated load control or for pulsed switch scanning. For example, they accept logic level signals from the microcontroller and are equipped with pull-down structures so that the input is well defined in case of an open connection. For more information, see the "Switch Interface Unit" section in the Atmel ATA664251 datasheet. The assignment of the current sources to the three PWM input pins is shown in Table 3-1. Table 3-1. CSx Port Configuration Table PWM Port CS1 CS2 CS3 CS4 CS5 CS6 CS7 CS8 PWM1 x - - - - - x X PWM2 - x - - x x - - PWM3 - - x x - - - - 3.1.13 PA0...7 Input/Output Pins All I/O pins are easily accessible - PA0...7 on Header X2. Most of the I/O ports are hardwired to the corresponding pins of the SBC. Table 3-4 on page 29 shows the connection between the Atmel ATtiny167 and the SBC. Cut-straps are available to remove the connection between the AVR and the SBC. For more information about the function of the I/O pins, please see the datasheet of the Atmel ATA664251. 3.1.14 PB0...7 Input/Output Pins All I/O pins are easily accessible - PB0...7 on header X3a and X3b. Most of the I/O ports are hardwired to the corresponding pins of the SBC. Table 3-2 shows the connection between the Atmel ATtiny167 and the SBC. A cut-straps are available to remove the connection between the AVR and the SBC. For more information about the function of the I/O pins, please see the Atmel ATA664251 datasheet. Table 3-2. 20 Hardwire Connections between the Atmel ATtiny167 and the SBC Table ATtiny167 SBC PA0 RXD PA1 TXD PA2 To switch S21 PA3 VDIV PA4 To switch S20 PA5 To switch S20 PA6 NCS PA7 Over C300 (100nF) to GND PB0 To switch S21 PB1 To switch S20 PB2 To switch S20 PB3 NTRIG PB4 PWM3 PB5 PWM2 PB6 NIRQ PB7 To jumper J12 ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 3.2 Pin Description - Atmel ATAB0004A Board (PC Interface Board) 3.2.1 PD4 to PD6 and PC5 Three LEDs are connected to PD4 - PD6 and are used for indicating the status of the SBC: Green LED connected to PD4, ON when the SBC is in active mode Yellow LED connected to PD5, ON when the SBC is in low active mode Red LED connected to PD6, ON when the SBC is in sleep mode A buzzer is connected to PC5. Currently not used, but if needed can easily be activated via software for any sound indication. 3.2.2 JTAG Header The JTAG header allows users to upload and debug their application with the JTAG programmer. Figure 3-4. The JTAG Header 3.2.3 ISP Header The ISP header can be used to program the Atmel(R) AT90USB1287 through in-system programming. Figure 3-5. 6-Pin ISP Connector Pinout ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 21 3.2.4 Reset Button The "RESET" push button resets the target AVR(R) device when pushed. Figure 3-6. Reset Button 3.2.5 Boot Loader Button The "HWB" push button is used to switch the AVR to DFU mode (boot loader). The HWB mode of this pin is active only when the HWBE fuse is enabled. The following steps enable DFU mode: 1. Press and hold the "HWB" push button. 2. Press the "RESET" push button. 3. Release the "RESET" push button. 4. Release the "HWB" push button. Figure 3-7. Boot Loader Button 3.2.6 Other Pins All remaining pins not described in this section do not have any special external circuitry and/or are used as described in detail in the next section. 22 ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 3.3 Summary of the Pin Connection As already described in detail in the previous sections, there are some pins tied together on the development board. The pin connection of the Atmel ATAB664251A board and ATAB0004A board is summarized in Table 3-3. Table 3-3. Summary of the Hardwired Pins on the Atmel ATA664251 Kit Connector Pin No. (PC Interface Board) Microcontroller Pin (AT90USB1287) Connected to Atmel ATA664251 Connector Pin No. (PC Interface Board) 1 PC1 NIRQx 1 2 PC6 NCSx 18 3 PC4 PWM2 2 4 PD2 RXD 17 5 PB5 PWM1 3 6 PE5 NTRIG 16 7 PD0 PWM3 4 8 PE4 NIRQ 15 9 PB1 SCK 5 10 PD3 TXD 14 11 PB0 NCS 6 12 PB3 MISO 13 13 PF0 VDIV 7 14 PB2 MOSI 12 15 GND GND 8 16 PB6/Reset NRES 11 17 PF1 VDIVx 9 18 VCC_AVR VCC_SBC 10 The three connections marked in bold are made via jumpers and the other connections are hardwired with a test point for easy access. ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 23 3.4 Jumper Description In order to be more flexible and to meet as many requirements as possible, some jumpers are provided on the development board. With the help of these jumpers, users have the opportunity to work with the system itself in order to test some features and/or to modify the system to meet their requirements. In the following sections all jumpers on the development board are briefly described. Figure 3-8. Jumpers on the Atmel ATAK43001-V1 Kit 3.4.1 Jumper VCC - J1 (PC Interface Board) There are three different ways to supply the microcontroller: Directly from the USB bus (5V supply) (jumper between 2 and 3) Via an on-board voltage regulator (3.3V supply) (jumper between 1 and 2) or Via the voltage regulator of the Atmel ATA664251 device (5V); jumper JP1 should be left unconnected and jumper JP16 should be set (left side). By default, this jumper is set connecting the microcontroller to the USB bus supply. Changing the position of this jumper causes the microcontroller to be supplied via the on-board 3.3V voltage regulator. To supply the microcontroller (AT90USB1287) from the voltage regulator of the Atmel ATA664251 device, remove this jumper and set jumper J16 (left side). 3.4.2 Jumper Reset - J2 (PC Interface Board) By default, this jumper is set connecting the NRES output of the LIN SBC and PB6 input of the microcontroller. If desired or needed, or when simply changing the position of this jumper, the NRES could be connected to the reset input of the microcontroller. This means the microcontroller is reset in the event of watchdog failure or undervoltage at the voltage regulator output. It is helpful to leave the jumper in the default position for testing purposes, debugging, etc. 3.4.3 Jumper Reset - J12 (Atmel ATAB664251A Board) By default, this jumper is set with the NRES output of the Atmel ATtiny167 and GND connected, thus holding the microcontroller inside the Atmel ATA664251 device in reset. In this case the SBC is controlled from GUI via the AT90USB1287 (on the PC interface board). To enable the ATtiny167 move this jumper to the left position or leave it open and make sure that the jumper J16 is also set in the left position. Setting the jumper J12 in the left position connects the reset pin of the Atmel ATtiny167 with the NRES pin of the SBC. This means the ATtiny167 is reset in the event of watchdog failure or undervoltage at the voltage regulator output. It is helpful to leave the jumper open for testing purposes, debugging, etc. 24 ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 3.4.4 Jumper SBC VCC - J16 (Atmel ATAB664251A Board) By default, this jumper is not set and the microcontroller (AT90USB1287) is supplied either from the USB or from 3.3V external voltage regulator. To supply the microcontroller (AT90USB1287) via the voltage regulator of the Atmel ATA664251 this jumper has to be set on the left side and the jumper J1 (PC interface board) has to be removed. Setting this jumper on the right side the Atmel ATtiny167 within the Atmel ATA664251 device powers it. In this case please make sure that neither the jumper J12 is set to the right side (GND) nor the PC interface board is plugged to the ATAB664251A board. 3.4.5 Jumper Settings for the CSx Ports (Atmel ATAB664251A Board) The I/Os pins are intended for contact monitoring and/or constant current sourcing. For maximum flexibility there are various components that can be easily connected to the HV I/O ports. The following sections provide a detailed description of how the CSx port hardware can be configured. 3.4.5.1 Jumpers of CS1...3 Jumper JP1...3 With the jumper header JP1...3 the user can select whether an RGB LED, three simple LEDs (connected in series), rotary switch, or a push button is connected to the respective CSx port. Figure 3-9. Jumpers JP1...3 By default, this jumper is set so that the CS1...3 ports are connected to the three simple LEDs (red) - LD1...3, LD7...9 and LD13...15. Those LEDs are hardwired to VBAT so that the LEDs are turned on when one or all of the CS1...3 ports are configured as low-side and are enabled. For demonstration purposes a second jumper (in addition to the default jumper) could be set, connecting the three green LEDs, showing that by only changing one bit the CS1...3 ports can be configured as high-side or low-side. In the case the supply voltage has to be lower than 10V (see Figure 8-2 on page 46). If customer-specific circuitry needs to be connected to one or all of the CS1...3 ports, the jumper has to be disconnected and the customer circuitry can then be connected to one of the pins on the upper side of the pin headers PJ1...3. ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 25 Jumper JP9...JP11 The I/Os pins CS1 to CS3 can be configured either as current sources (such as for switches toward ground) or as current sinks (such as for switches toward battery). With the jumpers JP9...11 the user can specify if the particular CSx port should be connected to ground or the VBAT. By default, these jumpers are set connecting the CS1...3 ports with VBAT. 3.4.5.2 Jumper of CS4...8 - JP4...8 With the jumper header JP4...8 the user can select whether three simple LEDs (connected in series), a rotary switch, or a push button is connected to a given CSx port. By default, this jumper is set so that the CS4...8 ports are connected to the three simple LEDs (green) - LD19...33. If customer-specific circuitry needs to be connected to one or all of the CS4...8 ports, the jumper has to be disconnected and the customer circuitry can then be connected to one of the pins on the upper side of the pin headers PJ4...8. Figure 3-10. Jumpers JP4...8 26 ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 3.5 LEDs Description Figure 3-11. LEDs on the Atmel ATAK43001-V1 Kit 3.5.1 Power LED (PC Interface Board) The blue USB power LED is connected directly to the VCC pin of the USB connector (see Figure 3-11, reference point 19). The SBC power LED is always lit when power is available at the USB connector. 3.5.2 Power LED (Atmel ATAB664251A Board) The blue SBC power LED is connected directly to the VS pin of the Atmel ATA664251 device (see Figure 3-11, reference point 24). The SBC power LED is always lit when power is available at the VBAT and GND connector (reference point 1). For current consumption measuring purposes the SBC power LED and the VCC SBC LED might have to be disabled. To do so, the resistors R38 and R39 have to be desoldered. 3.5.3 Mode Status LEDs (PC Interface Board) There are 3 LEDs (see Figure 3-11, reference point 21) on the PC interface board. The preprogrammed firmware in the Atmel AT90USB1287 uses these 3 LEDs to display the current mode of the Atmel ATA664251: LD4 (green) - active mode LD3 (red) - sleep mode LD2 (yellow) - active low-power mode These 3 LEDs can be used for any indication or debug purposes. 3.5.4 VCC SBC LED (Atmel ATAB664251A Board) The green VCC SBC LED on the Atmel ATA66xA board is connected directly to the VCC pin of the Atmel ATA664251 device (see Figure 3-11, reference point 19). This LED is always lit when the Atmel ATA664251 is in active mode. The voltage regulator of the Atmel ATA664251 device is only on in active mode; in all other modes it is off. ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 27 3.5.5 RGB LED (Atmel ATAB664251A Board) An RGB LED is mounted on the Atmel ATA664251 board to demonstrate that the Atmel ATA664251 is capable of driving RGB LEDs. The RGB LED is connected via jumpers J1...J3 to the CSx ports as follows: CS1 - blue CS2 - red CS3 - green The RGB LED is hardwired to GND. Therefore, when using the RGB LED (see Section "Jumper JP1...3" on page 25 for correct jumper settings), the CS1...3 ports have to be high-side configured. The RGB LED can be permanently driven with the selected constant current (see Section 3.6.6 "Changing the Current Level of the Current Sources" on page 31) from the CS1...3 ports or with PWM signals fed on the PWM1...3 pins of the Atmel ATA664251 device (for more information, see Section 5. "Atmel ATA664251 Demo GUI Description" on page 33 and the Atmel ATA664251 datasheet). 3.5.6 Low-Side LEDs (Atmel ATAB664251A Board) The red LEDs LD1...3, LD7...9 and LD13...15 are hardwired to VBAT and via the jumpers JP1...JP3 to the CS1...3 ports of the Atmel ATA664251 device. When one or all of the CS1...3 ports is/are configured as low-side and enabled, and the jumpers JP1...3 are set so that the red LEDs are connected to the CS1...3 ports (see Section "Jumper JP1...3" on page 25 for correct jumper settings), then the red LEDs are lit. 3.5.7 High-Side LEDs (Atmel ATAB664251A Board) The green LEDs LD4...6, LD10...12 and LD16...33 are hardwired to VBAT and via the jumpers JP1...JP8 to all CS1...8 ports of the Atmel ATA664251 device. When one or all of the CS1...8 ports is/are enabled (CS1...3 have to be configured as low-side) and the jumpers JP1...8 are set so that the green LEDs are connected to the CS1...8 ports (see Section "Jumper JP1...3" on page 25 and Section 3.4.5.2 "Jumper of CS4...8 - JP4...8" on page 26 for correct jumper settings), then the green LEDs are lit. 3.6 Other Components The development board for the Atmel ATA664251 comes with some additional components which can be replaced in order to adapt the LIN node to user-specific requirements. These components are shown and described in the following sections. 3.6.1 Push Buttons (Atmel ATAB664251A Board) There are eight push buttons on the Atmel ATA664251 board demonstrating the switch scanning/monitoring capability of the Atmel ATA664251. The push buttons S1...3 can be connected to GND or VBAT via the jumpers JP9...11. The push buttons 4...8 are hardwired to GND. All 8 push buttons are connected to the CS1...8 ports via the jumpers JP1...8 (see Section "Jumper JP1...3" on page 25 and Section 3.4.5.2 "Jumper of CS4...8 - JP4...8" on page 26 for correct jumper settings). 28 ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 3.6.2 Rotary Switches (Atmel ATAB664251A Board) Eight rotary switches are mounted on the Atmel ATAB664251A board to simulate coded switches. The rotary switches S can be connected to GND or VBAT via the jumpers JP9...11. The rotary switches S10, S12, S14, and S16 are hardwired to GND. All eight rotary switches are connected to the CS1...8 ports via the jumpers JP1...8 (see Section "Jumper JP1...3" on page 25 and Section 3.4.5.2 "Jumper of CS4...8 - JP4...8" on page 26 for correct jumper settings). Figure 3-12. Rotary Switches S2, S4, and S6 Figure 3-13. Rotary Switches S10, S12, S14, and S16 Table 3-4. Coding of the Rotary Switches Position 0 1 2 3 4 5 6 7 8 Code 4 X 2 1 X X X X X X X X X 8 9 X X X ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 X 29 When one or all of the CS1...8 ports is/are enabled and the jumpers JP1...8 are set so that the rotary switches are connected to the CS1...8 ports (see Section "Jumper JP1...3" on page 25 and Section 3.4.5.2 "Jumper of CS4...8 - JP4...8" on page 26 for correct jumper settings), a different voltage value resulting from the CSx output current, dependent on the position of the rotary switch, can be measured (and displayed in the GUI) on the VDIV pin (see also Section 5.6 "Voltage Divider Section" on page 38). 3.6.3 Configuring the Atmel ATAK43001-V1 Kit as a Master or a Slave Node Both the LIN2.0 and LIN2.1 specifications specify that the master node in a LIN network has to be set up as shown below. Figure 3-14. External Circuitry for a LIN Master Node The difference between a master node and a slave node with regard to the hardware is the additional diode Dser_master together with a serial 1k pull-up resistor between Vsup and the LIN line. The two components D1 and R42 on the ATA66B4251A board required for LIN master applications are shown in Figure 3-15. Figure 3-15. The Diode and Resistor Required for LIN Master Applications 30 ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 3.6.4 Generating a Local Wake-Up on CL15 A positive edge at pin CL15 followed by a high-voltage level for a given time period (> tCL15deb) results in a local wake-up request and the device switches to active mode. The debounce time ensures that no transients at CL15 create a wake-up. In order to show this function easily a switch is implemented between the CL15 pin and VS. When the device is in sleep mode, pressing the S115 switch generates a wake-up pulse. The local wake-up request is indicated by a low level at the NIRQ pin, generating an interrupt for the microcontroller, which is displayed in the GUI. Figure 3-16. Button for Local Wake-Up on CL15 3.6.5 Changing the Watchdog Timings On the Atmel ATA66B4251A board, the watchdog timing is generated by default with the help of the 51k resistor R2 connected between the WD_OSC pin and ground. In order to change these timings, the resistor R2 has to be changed. A description of how the R2 resistor influences the watchdog timing can be found in Section 5.7 "Watchdog Section" on page 39 (NTRIG, WD_OSC, and NRES) and in the Atmel ATA664251 datasheet. 3.6.6 Changing the Current Level of the Current Sources The current sources are available in active mode. They deliver a current level derived from a reference value measured at the IREF pin. This pin is voltage-stabilized (VIREF = 1.23V typ.) so that the reference current is directly dependent on the externally applied resistor (R3) connected between the IREF pin and ground. The resulting current at the CSx- pins is (1.23V/RIref) rICS. By default, a 12k resistor is mounted between IREF and GND; therefore the resulting current at the CSx pins is 10mA (assumed IMUL = '0' => rICS_H = 100). Both a missing and a short-circuited resistor are detected. In this case, an internally generated reference current IIREFfs is used instead to maintain fail-safe functionality. 3.6.7 Using the ATAB664251A Board Stand-Alone The Atmel ATA664251 kit allows users to learn more about Atmel ATA664251 device features by using the demo GUI but also to build their own applications and write own software using the kit. Only a few steps are needed to prepare the kit before creating your own applications. First, disconnect the PC interface board from the ATAB664251A board, then remove the J12 jumper (for debug and test purposes it should be left open) and set the J16 jumper to the right side. Now after powering up the board the Atmel ATA664251 (the ATtiny167 and the SBC) device is ready for use. The Atmel ATtiny167 can be programmed and debugged with an appropriate programming tool via the ISP1 connector. For applications where the 3x different PWM signals have to be generated to control the CS1...8 HV I/O ports (for example, RGB LED control), the Atmel ATtiny167 and the SBC have to be interconnected in a different way because the timers of the Atmel ATtiny167 are available on certain I/O pins only. The SPI pins (MISO, MOSI, and SCK) have an alternate function which is needed to generate PWM signal. That is why instead of the SPI the USI interface has to be used for communicating with the SBC. Two SMD DIP switches are included on the board to facilitate quick rerouting of the MISO, MOSI, and SCK SBC lines to the corresponding Atmel ATtiny167 I/O pins. ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 31 4. Programming and Debugging The easiest way to program and to debug the Atmel(R) AT90USB1287 is to use the Atmel Studio environment together with the STK500/600 or the JTAG-ICE MkII from Atmel. Atmel Studio is an integrated development platform (IDP) for writing and debugging AVR applications in Windows(R) 9x/Me/NT/2000/XP/7 environments. Atmel Studio provides a project management tool, source file editor, chip simulator, and in-circuit emulator interface for the powerful AVR 8-bit RISC family of microcontrollers. 4.1 Programming Connect the selected hardware (STK500/600 or JTAG-ICE MkII) to the ISP or JTAG header of the ATAB0004A board respectively. Pin "1" is marked with two small triangles on the board. In the Atmel Studio select the Atmel AT90USB1287. For more information about using the STK500/600, the JTAG-ICE MkII, or the Atmel Studio, see the relevant documentation available on the Internet. 4.2 Debugging Combined with Atmel Studio, the JTAGICE MkII can perform on-chip debugging on all AVR 8-bit RISC microcontrollers with a JTAG or debugWIRE interface. The Atmel AT90USB1287 comes with a debugWIRE interface so only a minimum of three wires is required for communication between the JTAGICE MkII and the board. These signals are RESET, VCC, and GND. The debugWIRE on-chip debug system uses a one-wire bidirectional interface to control the program flow, execute AVR instructions in the CPU, and to program the different non-volatile memories. For debugging via debugWIRE, the reset line is used and the NRES jumper has to be removed because the JTAG ICE mkII requires exclusive access to this line. For more detailed information about debugging via the debugWIRE interface, see the relevant documentation available on the Internet. 32 ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 5. Atmel ATA664251 Demo GUI Description The Atmel(R) ATA664251 demo GUI (graphical user interface) is a software tool for configuring and demonstrating the Atmel ATA664251 device using the Atmel ATAK43001-V1 kit. The Atmel ATA664251 demo GUI was designed to minimize the learning curve for using the Atmel ATA664251 device in the user application. It is divided into 11 main sections: SBC: general SBC settings and mode status Current SBC Status: displays the current SBC status (16-bit status register) Command Builder: builds a specific command and sends to the SBC SPI-Log-Window: the complete SPI communication is logged in here I/O Ports: configuration settings for all high-voltage I/O ports Voltage Divider: voltage divider settings and display of the currently measured voltage Watchdog: watchdog settings LIN: LIN interface settings PWMx: PWM test settings for the three different PWM inputs Figure 5-1. Atmel ATA664251 Demo GUI In the following section the Atmel ATA664251 demo GUI sections are described in detail, including some examples showing how to configure the Atmel ATA664251 device. ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 33 5.1 SBC Section After executing the Atmel ATA6641xx_Demo.exe file, the Atmel ATA664251 is automatically set to active low-power mode. This is indicated in the GUI: Figure 5-2 (yellow LED - ActiveLP is ON) and on the PC interface board (LED - LD2 is ON (reference point 21)) as well (please see Figure 2-12 on page 13). In this mode, only the VCC voltage regulator is active and can therefore supply the application's microcontroller. All other functions of the Atmel ATA664251 are disabled in the configuration register or inhibited by the PWM pins for the CSx pin current sources. This reduces the current consumption of the chip itself to a low-power range typically below 50A. Note that this is only valid if the chip select input of the SPI, NCS, is also kept at a high level. If it is pulled to ground, SPI communication is enabled, causing higher current consumption. The Atmel ATA664251 can easily be set to active mode (simply press the "Active Mode" button) with all peripherals/functions enabled, or set to sleep mode (simply press the "Go to Sleep" button), which switches off all peripherals, i.e., the LIN transceiver, the watchdog, the voltage dividers, the switch interface unit, and the VCC voltage regulator. The overall supply current on the VS pin is then reduced to a minimum (typ. 8A). In sleep mode the GUI is also disabled and no changes can be made as long as the device is in sleep mode. Two wake-up mechanisms are possible for leaving the sleep mode again: wake-up via LIN and wake-up via CL15. A wakeup via CL15 is easily generated by pressing the S115 switch. The SPI data rate can be modified; it is 4MHz by default. Figure 5-2. SBC Section 5.2 Current SBC Status Section Section 5.2 "Current SBC Status Section" on page 34 indicates the status of the Atmel ATA664251. The 16 bits of the status register, NRES, and NIRQ are displayed where the 16 status bits are updated after a new SPI command. This means, for example, that if you enable the watchdog with an SPI command, the status "Watchdog Active" is not reported in this data transmission but in the next one. Depending on the setting of the VDIVE bit, the bits 15 to 12 in the status register have a different meaning: VDIVE=0: bits 15 to 12 show the overtemperature status of different peripherals. Figure 5-3. Current SBC Status Section VDIVE=0 34 ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 VDIVE=1: bits 15 to 12 show the selected source for the voltage monitor (VBATT or CS1...8). Figure 5-4. Current SBC Status Section VDIVE=1 For more information on the single bits, see Table 7-4 in the Atmel ATA664251 datasheet. 5.3 Command Builder Section Section 5.3 "Command Builder Section" on page 35 gives the user the ability to create and send any command to the Atmel ATA664251 device. There are two possible ways to create a command: either by selecting the desired bits or just typing a sixteen-bit value into the "Data to Send" field (press "Enter" to activate the typed value). In order to avoid false watchdog disabling, the configuration bit (WDD) needs to be written twice. Therefore two consecutive SPI words are sent in order to alter the WDD bit to `1'. Depending on the setting of the CSPE bit, bit 1 in the configuration register has a different function: CSPE=0: bit #1 enables/disables the slope control of the CS ports Figure 5-5. Command Builder Section CSPE=0 CSPE=1: bit #1enables interrupt from addressed switch input (CS1...8) Figure 5-6. Command Builder Section CSPE=1 For more information on the single bits, see Table 7-1 in the Atmel ATA664251 datasheet. ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 35 5.4 SPI Log Window Section The complete communication to and from the Atmel ATA664251 device is logged into the "SPI Log Window." If a specific command has to be resent, just copy and paste it into the "Data to Send" field in Figure 5-7 and press "Send." Figure 5-7. Command Builder Section 5.5 I/O Ports Section A total of eight high-side current sources with high-voltage comparators and voltage dividers are available. Note that three of them (CS1, CS2, and CS3) can also be switched to low-side current sinks. All eight high-voltage I/O ports can be configured separately with the three or four configuration bits: CSE: Enable/disable addressed current source (CS1...CS8) CSC: Control of addressed current source (CS1...CS8) - controlled either by PWMy input or internally by CSE CSIE: Enable/disable from interrupt from addressed switch input (CS1...CS8) CSSSM: Switch between source/sink mode (CS1...CS3 only) The output current level can be divided by 2 using the IMUL bit. With the default setting of IMUL = `x100' the resulting current at the CSx- pins is (1.23V/R3) x 100 = 10mA (default value for R3 is 12k). The CSSCD bit is the one common control bit for all current sources. With this bit, the slope control of all eight sources can be disabled. By default, the slope control is activated and all currents are switched on and off smoothly. When setting this bit to `1' the current sources are enabled and disabled without transition times. In order to change the configuration of a certain current source via SPI, it must be addressed and the current source programming CSPE bit must be set to `1' (in the GUI this is done automatically). 36 ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 Figure 5-8. I/O Port Section Example 1: Enabling a particular current source and controlling it via the CSC bit or via the PWMy input: In this example, the CS1 port is connected to the green/red LEDs (the following is valid for CS1...8). Set the J1 jumper to the second position (counted from left to right). Then all that has to be done in the GUI is to select the corresponding CSE bit and CSC bit (for internal control) and press the "Configure CS1" button. Now the CS1 port is enabled as indicated by illuminated green LEDs and configured as the high-side current source and controlled by the internal logic. The control of the current source can be easily changed to be PWM-controlled by deselecting the CSC bit and pressing the "Configure CS1" button again; this turns off the LEDs. The PWM1 pin is assigned to the CS1 port. By default the PWM mode in the GUI is set to static-low, meaning the PWM1 input is actively kept to low. To turn on the LED the PWM must be changed to static-high, which is equal to CSC=1, or "pulsed" selected where the signal with default period (1ms) and pulse width (100s) is to be generated on the PWM1 pin. To adjust the brightness of the LEDs, simply change the period and the pulse width as desired. To configure the CS1 port as the low-side current source (this is only valid for CS1...3), simply set the CSSSM bit and set the jumper at the very first position on the left side. Example 2: Connecting a switch to a specific current source (Contact Monitoring): Now the CS1 port is connected to a tactile switch (S1) (the following is valid for CS1...8). Change the jumper setting of J1 to the second position from the right, with jumper J9 connecting the middle and right pin (the tactile switch is connected toward GND). Configure and enable a high-side current source for the CS1 port (set CSE and CSC bits and press "Configure CS1" button). From the voltage divider section, select the CS1 port as ADC source and activate continuous voltage measurement. By pressing the tactile switch (S1) the measured voltage in the voltage divider section changes to 0V because the CS1 port is then (when S1 is pressed) connected directly to GND. This status change is also indicated with the CS1CS bit in the status register. Please note that the status bits in the "Current SBC Status" section are updated only after an SPI command has been sent. Now the interrupt from the CS1 port is enabled and the CS1 port to be PWM1-controlled is configured. To do this, set the CSIE bit and deselect the CSC bit. Finally, press the "Configure CS1" button and set the pulsed mode in the PWM1 section. ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 37 Now the output state of the HV comparator is sampled with each falling edge of the PWMy or CSC signal. As soon as the sampled state changes (S1 pressed), an interrupt request is generated and reported by a low level on the NIRQ pin (automatically displayed in the "Current SBC Status" section). Please bear in mind that the NIRQ pin remains at ground until the end of the next SPI command. The same can be done when the CS1 port is configured as low-side current source (enable the CSSSM bit and change the setting of the J9 jumper to the left) (this is only valid for CS1...3). 5.6 Voltage Divider Section The VDIV pin provides a low-voltage signal for the microcontroller's ADC which is linearly dependent on the input voltage. It is sourced either by the VBATT pin or one of the switch input pins CS1 to CS8.The divider ratio of the measured input voltage for the Atmel ATA664251 is 1:4. This results in maximum output voltages on the VDIV pin when reaching 20V at the input. The voltage on this pin is actively clamped to VCC if the input value would lead to higher values. Figure 5-9. Voltage Divider Section The displayed voltage value in the voltage divider section is the result of the following equation: Input_Voltage = (Divider_Ratio VDIV_Value Reference_Voltage)/1023 Input_Voltage is the measured and displayed voltage. Divider_Ratio is 4. VDIV_Value is the measured voltage at the VDIV pin. Reference_Voltage is the internal reference voltage of the microcontroller, which is dependent on the microcontroller's supply voltage (for setting jumper J1 and J16, see Section 3.4.1 "Jumper VCC - J1 (PC Interface Board)" on page 24 and Section 3.4.4 "Jumper SBC VCC - J16 (Atmel ATAB664251A Board)" on page 25). Because the supply voltage of the microcontroller is not measured precisely, a fixed values of 5.0V for the Reference_Voltage is used. If a more precise display of the measured voltage is desired, the real supply voltage of the microcontroller has to be measured and typed in the "Ref. Voltage" field. This value is used in the equation above to calculate the input voltage only when the button is pressed. The input voltage can be measured continuously or at intervals. 38 ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 5.7 Watchdog Section The watchdog expects a trigger signal from the microcontroller at the NTRIG (negative edge) input within a time window of twd = tNTRIG. The trigger signal must exceed a minimum time ttrigmin > 7s. If a triggering signal is not received, a reset signal will be generated at output NRES. The timing basis of the watchdog is provided by the internal watchdog oscillator. Its time period, tWDosc, is adjustable between 20ms and 64ms using the external resistor R2 (34k ...120k; the default value is 51k). During sleep mode the watchdog is switched off to reduce current consumption. The GUI offers the option of experimenting with trigger values (simply change the tNTRIG value) or even disabling the trigger signal in order to gain a better understanding of how the watchdog works. Figure 5-10. Watchdog Section In order to avoid false watchdog disabling, this configuration bit (WDD) needs to be written twice. Therefore two consecutive SPI words are sent in order to alter the WDD bit to `1'. To disable the watchdog directly after power-up (e.g., for microcontroller programming or debugging purposes) (i.e., after external power-up or after sleep mode), the VDIV pin has to be tied to VCC until the start-up time treset of typ. 4ms has elapsed. The minimum time for the first watchdog pulse is required after the undervoltage reset at NRES disappears. It is defined as lead time td = 155ms (for more information, please see Section 10 in the Atmel ATA664251 datasheet). After wake-up from sleep mode, the lead time td starts with the positive edge of the NRES output. 5.8 LIN Section The LIN interface of the Atmel ATA664251 device has to be activated via an SPI command. This is done with the GUI by simply pressing the "LIN Interface" button. Figure 5-11. LIN Section The slope control of the LIN transceiver can be switched off to achieve higher bit rates (up to 200kBit/s). Then the slope time of the LIN falling edge is < 2s. The slope time of the rising edge greatly depends on the capacitive load and the pull-up resistance at the LIN line. To achieve a high bit rate Atmel recommends using a small external pull-up resistor (500) and a small capacitor. Superior EMC performance is not guaranteed in this high-speed mode. For test purposes a test signal (10Hz - 200kHz) can be generated at the TXD pin and if the LIN interface is enabled, the same signal can be observed at the LIN pin. In order to achieve any long dominant state on the pin LIN (such as PWM transmission or low bit rates), the time-out function can be easily disabled by pressing the "TXD Time-Out" button. ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 39 5.9 PWMy Section There are three PWM sections in the GUI where a specific PWM signal can be generated at the corresponding PWM inputs of the Atmel ATA664251 device. Figure 5-12. PWM Section The switch interface current sources can be controlled directly via the PWMy input pins, such as for pulse-width-modulated load control or for pulsed switch scanning. The assignment of the current sources to the three PWM input pins is shown in Table 5-1. Table 5-1. CSx Port Configuration Table PWM Port CS1 CS2 CS3 CS4 CS5 CS6 CS7 CS8 PWM1 x - - - - - x x PWM2 - x - - x x - - PWM3 - - x x - - - - To enable the external control functionality of a given current source the relevant CSC bit should be disabled (please see Section 5.5 "I/O Ports Section" on page 36). External PWM signals could be applied at the PWMy input pins or the GUI could be used to generate a PWM signal on the PWMy input pins. In the PWM 1...3 sections in the GUI three independent PWM signals can be generated; just type in the desired period and pulse width and select "pulsed" as the PWM mode. The PWM 3 signal is generated by using the 8 bit timer of the AT90USB1287 (PC Interface board), therefore fine settings for the "PWM3-Pulsewidth" are not possible like for the PWM 1 and PWM 2, where 16 bit timers are used to generate the PWM pulses. 40 ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 6. Operation Using the Default Software 6.1 Standalone Demonstration Quick Start User Guide As the SiP on the Atmel(R) ATAB664251A-V1.0 includes an Atmel ATtiny167 AVR(R) 8-bit microcontroller, the Atmel ATAB664251A-V1.0 board can operate "standalone" without the PC interface board connected. The following sections describe standalone operation with the default software programmed in the Atmel AVR 8-bit microcontroller. 6.1.1 6.1.2 Configuration for Standalone Operation 1. Disconnect the PC interface board 2. Configure the jumpers and switches Jumper reset - J12 (Atmel ATAB664251A board) Jumper J12 controls the reset signal to the Atmel ATtiny167 microcontroller. Remove jumper J12 or set jumper J12 in left side (NRES) for standalone operation. Refer to Section 3.4.3 "Jumper Reset - J12 (Atmel ATAB664251A Board)" on page 24 for additional information concerning this jumper. Jumper SBC VCC - J16 (Atmel ATAB664251A board) Jumper J16 controls the supply voltage to the Atmel ATtiny167 microcontroller. Set jumper J16 to the right side (VCC microcontroller) for standalone operation. Refer to Section 3.4.4 "Jumper SBC VCC - J16 (Atmel ATAB664251A Board)" on page 25 for additional information concerning this jumper. Jumper J1 to J3 Set jumpers J1, J2 and J3 each to the left-most position to connect the constant current source to the RGB LED (LD36). Jumper J4 Set jumpers J4 to the right-most position to connect to the push button S7. Jumper J5 to J8 Set jumpers J5, J6, J7 and J8 each to the left-most position to connect the constant current source to the green LED's (LD22 through LD33). Switch S20 and S21 Switches S20 and S21 are used to select the peripheral used for the SPI communication between the Atmel ATtiny167 microcontroller and the Atmel ATA664151 LINSBC. If both switches S20 and S21 are in the right position, the USI peripheral in the Atmel ATtiny167 microcontroller is used to communicate with the LINSBC. If both switches S20 and S21 are in the left position, the SPI peripheral in the Atmel ATtiny167 microcontroller is used to communicate with the LINSBC. For standalone operation with the default software programmed in the Atmel AVR 8-bit microcontroller, switches S20 and S21 should be set in the right position (USI). Header X4 Apply 12V power and ground to header X4. Standalone Demonstration Operation After applying power to header X4, the blue power LED (LD34) and green VCC SBC LED (LD35) should be on indicating power is supplied to the Atmel ATtiny167 microcontroller. The RGB LED (LD36) should show blue, the LEDs assigned to CS5 (LD22-LD24) should flash approximately 0.5 seconds on - 0.5 seconds off, and the LEDs connected to CS6 (LD25-LD27) should be on. After powering up, subsequent presses of the push button (S7) connected to CS4 will cycle LED's in the following manner, demonstrating the capabilities of the device to interface to switch type inputs and drive outputs: RGB LED (LD36): RED GREEN WHITE OFF BLUE RED ... LEDs connected to CS6-CS8 (LD25-LD33): Cycle through binary codes for 2 3 4 5 6 7 0 1 ... (LEDs connected to CS6 represent the least significant bit of the binary code) The LEDs connected to CS5 (LD22-LD24) should continue to blink on-off at the same rate. ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 41 6.2 LIN Slave Node Demonstration Quick Start User Guide The default standalone demonstration software also includes the capability for the Atmel(R) ATAB664251A board to operate as a LIN slave node responding to messages from a LIN master node. Among other things, the standalone demonstration illustrates the use of the LIN SIP for ambient lighting applications by controlling the RGB LED based on messages received from a LIN master node. 6.2.1 Configuration for Ambient Lighting LIN Slave Node The Atmel ATAB664251A board should be configured as described in Section 6.1.1 "Configuration for Standalone Operation" on page 41. In addition, the LIN BUS from the LIN master node should be connected to header X5. The Atmel AT32UC3C-EK evaluation kit (available separately) can be utilized as the LIN Master. Software is available from Atmel for this kit to configure it to send ambient lighting messages over the LIN bus in response to actions on the kit's user interface, allowing the user to send different RGB values to each of several ambient lighting slave nodes. Each slave node should respond only to the ambient lighting messages directed to its slave node address. 6.2.2 Ambient Lighting LIN Slave Node Operation The ambient lighting slave node address of the Atmel ATAB664251A board is selected using the push button (S7) connected to CS4. Successive presses of this push button increment the slave node addresses from 1 through 7; after address 7, a press of the push button selects an invalid slave address (meaning the board will not respond to any ambient lighting messages). A subsequent press of the push button after this starts the sequence again with a slave address of 1. The selected slave address is displayed in binary code on the LEDs connected to CS6-CS8 (LD25-LD33) with the LEDs connected to CS6 representing the least significant bit of the binary code. The invalid slave address is indicated by all the LEDs (LD25-LD33) being off. The Atmel ATAB664251A board will respond to ambient lighting messages targeted to its slave node address, allowing the RGB LED on the board to be controlled from a LIN master node. 6.2.3 LIN Messages Supported in the Default Software In addition to the LIN messages used for ambient lighting control, several other LIN messages are supported in the default software on the Atmel ATAB664251A board. These LIN messages allow for complete control of the LIN SBC features from a LIN master node. Table 6-1. LIN Messages Message Set SBC configuration register 0x23 Direction(1) Data Receive 2 bytes: Bit 15 to Bit 0: Set PWM period and duty 0x25 Receive 8 bytes: Bit 15 to Bit 0: Bit 31 to Bit 16: Bit 47 to Bit 32: Bit 63 to Bit 48: Set watchdog trigger period 0x26 Receive 1 byte: Bit 7 to Bit 0: Receive 4 bytes: Bit 7 to Bit 0: Bit 15 to Bit 8: Bit 23 to Bit 16: Bit 31 to Bit 24: Ambient lighting Note: 1. 0x2C Configuration register PWM Period PWM-1 duty cycle PWM-2 duty cycle PWM-3 duty cycle Trigger period Slave node address Red duty cycle Green duty cycle Blue duty cycle Notes 1 - The received value is transferred over SPI to the LIN SBC. 2 - Ambient lighting operation will not work properly after this message is received. Period and duty cycles are in terms of microseconds (us); 1 count = 1s. Watchdog trigger period is in terms of milliseconds (ms); 1 count = 1 ms. A period of 0 will not generate a trigger. Duty cycles are scaled to 255 counts; 255 counts = 100% duty cycle. 4 bytes: The transmitted value is the value Status register Bit 15 - Bit 0: obtained over SPI from the LIN SBC. VDIV A/D reading Bit 31 - Bit 16: Direction is relative to the Atmel ATAB664251A board configured by default software as a LIN slave Get SBC status register and VDIV 42 PID 0x24 Transmit ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 6.3 Default Software Overview The following depicts an overview of the default software programmed in the Atmel(R) ATtiny167 AVR(R) 8-bit microcontroller. Figure 6-1. Overview of the Default Software Reset Timer0 Overflow Interrup Periodic at 256s Rate AtaDevMCU_I ni t(): - 8MHz operat ion w/ int ernal clock AtaDevTi mer_I ni t(): Timer0: 1Mhz clock, overf low int errupt enabled. Provides syst em int errupt every 256s and "virt ual" 16 Bit PWM1 out put t o Swit chLI N SBC - Timer1: 8MHz clock, no int errupt s. Provides PWM2 and PWM3 out put s t o Swit chLI N SBC AtaDevAnal og_I ni t(): - Sof t ware t riggered conversion of VDI V input AtaDevSwi tchLI N_I ni t(): - Conf igure USI t o provide SPI int erf ace t o Swit chLI N SBC I ni ti al i ze PWM Duty Cycl es I ni ti al i ze Swi tchLI N SBC Confi gurati on I ni ti al i ze LI N Stack Enabl e I nterrupts Manage "virtual" 16 Bit (max) PWM generation for PWM1 output Provide 5ms scheduler tick for background Manage SwitchLIN SBC watchdog timer every 1ms Timer1 Compare A Interrup At PWM3 Period Completion and Duty Cycle Completion Manage PWM Generation for PWM3 Output AtaDevVDIV_Sample(): Start VDIV sampling Timer1 Compare B Interrup At PWM3 Period Completion and Duty Cycle Completion AtaDevSwitchLIN_GetStatusReg(): Read status register from SwitchLIN SBC Buffer Status Register for LIN Transmit AtaDevVDIV_Get(): Read VDIV from ADC Buffer VDIV for LIN transmission Manage PWM Generation for PWM2 Output Note: Through the Timer0 overflow interrupt and the Timer1 compare A/B interrupts, the software supports generation of the 3 PWM outputs at 3 different/ independent frequencies 5ms? LIN Transfer Complete LIN_Periodic_Tasks(): Manage LIN slave stack Process Received LIN Messages - If Set SBC Configuration Register Mesage: Update SwitchLIN SBC Configuration Register - If Set PWM Period and Duty Message: Update PWM period and duty - If Set Watchdog Trigger Period Message: Update SwitchLIN SBC watchdog trigger period - If Ambient Lighting Message: If for this node address then recale and update PWM period and duty At LIN Transfer Complete Event Manage LIN Communication LIN Error At LIN Error Event Manage LIN Communication Errors DebounceCS4_Switch(): Read CS4 push button input LIN Bus Active? Default SBC Configuration? USwitch Lin Standalone Demo(): If CS4 push button pressed, update PWM1 - 3 duty cycles in sequence AmbientLightingAddrUpdate(): If CS4 push button pressed, update node address and address LED Indicators Flash CS5 LED Manage SwitchLIN SBC Watchdog Trigger ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 43 7. Tools In combination with the STK500 and JTAG ICE MkII, Atmel Studio is a powerful tool for programming and debugging the AVR(R) microcontroller family in general. Furthermore, Atmel(R) provides cost-effective software support for the development of a LIN network. These can easily be used together with the development board. A LIN1.3 ANSI C software library for the AVR microcontroller family is available. The software library allows programming of protocol handling for LIN slave nodes. This library can be downloaded at http://www.atmel.com/Images/doc1637.pdf Many OEMs demand that their suppliers use certified third-party LIN protocol stacks. To meet this requirement there are LIN2.0 as well as LIN2.1 protocol stacks available for the large number of AVR microcontrollers from Mentor Graphics(R), Vector Informatik, Warwick Control Technologies, Dunasys, and from IHR. Warwick Control Technologies offers the NETGEN configuration and autocoder tool. For testing purposes and to provide a quick start to using Atmel products, there is a limited but free version available. The demo version is available at http://www.warwickcontrol.com/ For more information about the certified LIN stacks, please contact the third-party suppliers directly. 44 ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 8. Schematics of the Atmel ATAK43001-V1 Kit Figure 8-1. Schematics of the PC Interface Board ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 45 Figure 8-2. Schematics of the Atmel ATAB664251A Board 46 ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 9. Board Layout Figure 9-1. PC Interface Board Component Placement; Top Side, Top View Figure 9-2. PC Interface Board Component Placement; Bottom Side, Top View (as if PCB was Transparent) ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 47 Figure 9-3. PC Interface Board; Top Side, Top View Figure 9-4. PC Interface Board; Middle Layer 1, Top View (as if PCB was Transparent) 48 ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 Figure 9-5. PC Interface Board; Middle Layer 2, Top View (as if PCB was Transparent) Figure 9-6. PC Interface Board; Bottom Side, Top View (as if PCB was Transparent) ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 49 Figure 9-7. Atmel ATAB664251A Board Component Placement; Top Side, Top View Figure 9-8. Atmel ATAB664251A Board; Top Side, Top View Figure 9-9. Atmel ATAB664251A Board; Bottom Side, Top View (as if PCB is Transparent) 50 ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 10. Atmel ATA664251 Kit BOM Table 10-1. PC Interface Board BOM # Designator Quantity Value 1 C1, C2, C4, C6, C11, C12, C16 4 2 C3 1 3 C5, C17 5 C7 6 7 8 C13, C15 9 C14 11 D3 12 Voltage Tolerance Manufacturer and Part Number Description Footprint 100nF CAP 0402 0402_C 1F CAP 0603 0603_C 1 10F CAP 0603 0603_C 1 150pF CAP 0402 0402_C C8 1 15nF CAP 0402 0402_C C9, C10 2 22pF CAP 0402 0402_C 2 1F CAP 0402 0402_C 1 10nF CAP 0402 0402_C 1 BAS516 SOD523_D RS No: 508-282; Mfg P/N: BAS516 ISP1 1 Header, 3-Pin, Dual Row HDR2X3_CEN 2.54mm Samtec TSW-105-24-S-D 13 J1, J2 2 Header, 3-Pin Jumper 1x3 1.27mm Samtec - MTMS-103.51S-S-130 14 JTAG1 1 HDR 5X2 100MIL HDR2X5_ JTAG 2.54mm Samtec 15 L1 1 IND 0603 EMI 0603_L Mouser No: 875MI0603J601R-10 16 L2 1 10H Class Inductor 0603_L Wurth: 744 796 8 0603_LED_BL RS No: 700-8026 17 LD1 1 Typical BLUE GaAs LED 18 LD2 1 Typical YELLOW GaAs LED 0603_LED_GE 19 LD3 1 Typical RED GaAs LED 0603_LED_rt RS No: 466-3728P 20 LD4 1 Typical GREEN GaAs LED 0603_LED_gn RS No: 466-3706P 21 Q1 1 16MHz Crystal Unit SMD 2.5x2.0mm CX2520 Kyocera - CX2520SB 22 R3, R4 2 22R RES 0402 1k 5% 0.1W 0402_R 23 R6 1 1k RES 0402 1k 5% 0.1W 0402_R 24 R7, R8, R9 3 825R RES 0402 1k 5% 0.1W 0402_R 25 R10 1 180R RES 0402 1k 5% 0.1W 0402_R 26 R15, R16 2 47k RES 0402 0 5% 0.1W 0402_R 27 R20, R21, R22 3 nc 28 S1, S2 2 Tact Switch Vertical SMD B3U-1000P RS No: 682-1421 29 Sp1 1 Buzzer, e.g., BST5523SA Buzzer_BST Mouser No: 665SMT0540SR 30 T1 1 High-Voltage NPN Transistor SOT23-3 RS No: 545-0438P; Mfg P/N: MMBTA42LT1G 0603_R ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 51 Table 10-1. PC Interface Board BOM (Continued) Description Footprint Manufacturer and Part Number 1 Header, 4-Pin, Dual Row HDR2X4_CEN Samtec QFN64_5x5 Atmel - AT90USB1287 # Designator Quantity 31 TFT1 Value Class Voltage Tolerance 32 U1 1 8-bit Microcontroller with 64/128Kbytes of ISP Flash and USB Controller 33 U2 1 VREG, 3.3V, 500A MLF 6-Pin DigiKey No: 576-2768-1ND; MIC5219 34 X1 1 Mini USB Connector USB-micro Samtec UUSB_B_S_S_SM_TR 35 X2 1 Header, 9-Pin, Dual Row BCS-109-X-DHE Samtec BCS-109-X-D-HE Description Footprint Manufacturer and Part Number Table 10-2. Atmel ATAB664251A Board BOM # Designator Quantity Value 1 U1 1 - ATA664251 QFN32 5x5mm 47nF Surface-Mount Ceramic Multilayer Capacitor RC-0402 100nF Surface-Mount Ceramic Multilayer Capacitor RC-0402 100nF 50V Surface-Mount Ceramic Multilayer Capacitor RC-0603 50V 10% Surface-Mount Ceramic Multilayer Capacitor R3225 5% Surface-Mount Ceramic Multilayer Capacitor RC-0603 5% Surface-Mount Ceramic Multilayer Capacitor RC-0402 5% Surface-Mount Ceramic Multilayer Capacitor RC-0402 Diode RC-1608 Jumper 1x3 2mm J12 2 C3 3 C7, C10, C11, C300 4 5 6 7 C5 C6 C8 C2, C4 4 4 1 1 1 2 10F 2.2F 10nF X7R Voltage COG COG COG 50V (C2 only) Atmel ATA664251 Mouser No: 81GRM32ER71H106KA2L C1 1 9 D1, D7 2 10 J12 1 11 J16 1 - Jumper 1x3 2mm Samtec 12 J9, J10, J11 3 - Jumper 1x3 2mm Samtec MTMM-103-04-T-S-140 ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 50V Tolerance 8 52 220pF Class BAV302 Table 10-2. Atmel ATAB664251A Board BOM (Continued) Value Class Voltage Tolerance Description Footprint Manufacturer and Part Number # Designator Quantity 13 J1, J2, J3 3 Jumper 2x5 2mm Samtec 14 J4, J5, J6, J7, J8 5 Jumper 2x3 2mm Samtec MTMM-103-04-T-D-140 15 X1 Header 2x9 2,54mm Samtec TSW-109-08-L-D-RA 16 X2 Header 2x4 2.54mm 17 LD34 1 LED Blue RC-0603 RS No: 700-8026 LD1, LD2, LD3, LD7, LD8, LD9, 18 LD13, LD14, LD15, 9 LED Red RC-0603 RS No: 466-3728P LD4, LD5, LD6,LD10, LD11, LD12, LD16, LD17, LD18, LD19, LD20, 19 LD21, LD22, LD23, LD24, LD25, LD26, LD27, LD28, LD29, LD30, LD31, LD32, LD33, LD35 25 LED Green RC-0603 RS No: 466-3706P 20 LD36 1 RGB-LED P-LCC-6 RS No: 708-0747P 21 GND 1 Messbuegel 22 VB, GND, CL15, LIN 2 MessPin 1x2 2.54mm 23 R3 1 12k Chip Resistor Surface Mount RC-0402 24 R39 1 430R Chip Resistor Surface Mount RC-0402 25 R40, R41 1 10k Chip Resistor Surface Mount RC-0402 26 R42 1 1k Chip Resistor Surface Mount R2012 27 R36, R42 2 47k Chip Resistor Surface Mount RC-0402 28 R2 1 51k Chip Resistor Surface Mount RC-0402 29 R38 1 1k Chip Resistor Surface Mount RC-0402 30 R37 1 56R Chip Resistor Surface Mount RC-0402 31 R4, R8, R12, R16, R20, R27, R31, R35 8 820R Chip Resistor Surface Mount RC-0402 32 R5, R9, R13, R17, R21, R26, R30, R34 8 200R Chip Resistor Surface Mount RC-0402 33 R6, R10, R14, R18, R22, R25, R29, R33 8 100R Chip Resistor Surface Mount RC-0402 34 R7, R11, R15, R19, R23, R24, R28, R32 8 390R Chip Resistor Surface Mount RC-0402 ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 53 Table 10-2. Atmel ATAB664251A Board BOM (Continued) # Designator Quantity 35 S1, S3, S5, S7, S9, S11, S13, S15, S115 36 Class Footprint 9 Tact Switch Vertical SMD TL1015 Mouser No: 612-TL1015AF S2, S4, S6, S8, S10, S12, S14,S16 8 Rotary Switch SMR_SW RS No:702-3381P 37 S20, S21 2 SMD DIP Switch 38 X3a, X3b 2 Header 2x2 2.54mm 39 ISP1 1 Header 2x3 2.54mm ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 Voltage Tolerance Manufacturer and Part Number Description 54 Value 11. Revision History Please note that the following page numbers referred to in this section refer to the specific revision mentioned, not to this document. Revision No. History 9300D-AUTO-03/15 Put document in the latest template ATAN0063 [APPLICATION NOTE] 9300D-AUTO-03/15 55 XXXXXX Atmel Corporation 1600 Technology Drive, San Jose, CA 95110 USA T: (+1)(408) 441.0311 F: (+1)(408) 436.4200 | www.atmel.com (c) 2015 Atmel Corporation. / Rev.: 9300D-AUTO-03/15 Atmel(R), Atmel logo and combinations thereof, Enabling Unlimited Possibilities(R), AVR(R), and others are registered trademarks or trademarks of Atmel Corporation in U.S. and other countries. Other terms and product names may be trademarks of others. DISCLAIMER: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. SAFETY-CRITICAL, MILITARY, AND AUTOMOTIVE APPLICATIONS DISCLAIMER: Atmel products are not designed for and will not be used in connection with any applications where the failure of such products would reasonably be expected to result in significant personal injury or death ("Safety-Critical Applications") without an Atmel officer's specific written consent. Safety-Critical Applications include, without limitation, life support devices and systems, equipment or systems for the operation of nuclear facilities and weapons systems. Atmel products are not designed nor intended for use in military or aerospace applications or environments unless specifically designated by Atmel as military-grade. Atmel products are not designed nor intended for use in automotive applications unless specifically designated by Atmel as automotive-grade. Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Atmel: ATAK43001-V1